SPL REPAIR TO BLDG NO T-137 AT SAND MODAL HILL LAILAPUR, STREET LIGHT CONVERSION OF OH LINE INTO UG CABLE FOR SECURITY LIGHTS FROM SAND MODEL TO BARAK HILLS, PROVN OF HANGER LIGHTS FOR MT, OTHER ALLIED WKS AT CIJW SCHOOL VAIRENGTE UNDER GE SILCHAR

B and R Division Items

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified & directed.

Demolition of cement concrete (reinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified & directed.

Demolition of brick/stone masonry, built in cement mortar including all quoins, arches, pillars etc but exluding ashlars facings, dressed stone work and pre-cast concrete articles all as directed.

Demolition of reed, lathing single or double including battens and plaster or chiken wire lathing

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises

Dismantling of wall and ceiling boards (fibre, pulp, insulation boards etc) any thickness including cover fillets.

Dismantling of Plain or corrugated steel sheeting, any gauge, thickness as in roof coverings, chajja, wall clading and the like complete all as specified and directed

Dismantlig timber scantling in any position unframed work 40sqcm and over in section complete all as specified & directed.

Taking down chowkats or frames with Shutters (without taking off shutters from the frame) not exc. 1.5 sq. m each complete all as specified & directed.

Taking down chowkats or frames with Shutters (without taking off shutters from the frame) exc. 1.5 sq. m but not exc. 4 sq. m each complete all as specified & directed.

Use and waste of formwork to edges of concrete flats, treads, window cills, floor and roofs n exc 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but not exc 20cm wide rough finished flat surfaces complete all as specified .

M & L for brickwork with subclass 'B' or locally available best quality old size bricks, straight or curved on plan exc 6 m mean raduis, built in CM (1:4} as half brick thick wall all as specified & directed.

M&L for RCC 1:1.5:3 type A-1 (using 20 mm graded stone aggregates) as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified & directed.

Material and labour for Rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar (1:6) on wall surface and finishing even and fair complete all as specified and directed

Material and labour for Rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar (1:4) on wall surface with top 5 mm layer mixed with water proofing compound and finishing even and fare complete all as specified and directed. NOTE : Water proofing compound shall be measured & paid separately.

Supply only integral water proofing compound.

M& L for Vetrified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust complete all as specified and as directed .

M&L for Coloured Glazed ceramic tiles in vertical surface 300x450x 7 mm thick joint free set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specified & directed.

Material and Labour for applying 1mm thick wall care putty on new or previously untreated plastered surfaces of walls, including preparation, to make the surface even and smooth all as specified and directed.

Material and Labour for applying 1mm thick weather proof wall care putty on new or previously untreated plastered surfaces of walls, including preparation, to make the surface even and smooth all as specified and directed.

Material and Labour for applying two coats of acrylic distemper over a coat of alkali resistant primer including preparation of newly plastered surfaces, all as specified and directed.

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified & directed.

Material and Labour for mild steel TMT bars 10mm dia and over cut to length bend to shape required including cranking bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or secruing with clips complete all as specified & directed.

Material and labour for Mild steel TMT bars of Fe 500 or Fe 500D, 6 mm dia and over upto and including 10 mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips complete all as specified and directed.

Supply and fix Steel work in trusses, purlins, posts and the like using tubular/ square hollow sections including special shaped washer etc. complete using ERW or induction butt welded tubes/SHS conforming to IS.1161 - 2014 / IS.4923 - 1997 grade St.-240 complete all as specified and directed

S&F Rolled Mild Steel Fe 410 -W (Gde- E- 250) quality- A in Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified & directed.

Supply & Fix Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors, railings, and similar work conforming to Fe.290.Gde-E-165 complete all as specified & directed.

Material and Labour for Plain cement concrete 1:3:6 type C-1 using 20 mm graded stone aggregate as in bed block or hold fast block complete all as specified and directed.

S&F for Pre-painted galvaume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed.

S&F for Pre-painted galvaume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed.

S&F 35mm thick plain framed 2nd cl hardwood panelled shutter (two panels ) with lock rail & panel of 9mm BWP commercial ply or 12mm veneered particle with commercial veneering on both face, the size of rail and style as per IS 1003 (Part-1) kiln seasoned and chemically pressed, treated complete incl 15 to 20 mm tapering bedding on one face of second cl hardwood fitted to chowkhats complete all as specified.

S&F factory made 2nd class 35 mm thick hardwood glazed and skelton shutters open rebated and prepared to receive glass / gauze etc ( with or without sash bars) divided into square with plain, chamfered or rounded fixed with cut : mitered beads for receiving gauge etc size of members of shutters as specified in SSR Part-I section 8 cluse 8.24(a) complete all as specified.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of apertue 1.40mm and fixed with stainless steel wire staples complete all as specified.

M & L for applying two coats of synthetic enamel paint over one coat of pink primer including preparation of new or previously untreated wood and wood based surfaces Surfaces of any description, not otherwise described, over 10cm width or girth

S&F 300 mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified & directed.

Supply and fix 100 mm size stainless steel butt hinges (ISI marked) with stainless steel screws all as specified and directed.

Supply and fix for 150mm extruded Aluminium alloy handles, cast type all as specified & directed.

Supply and fix for 200mm long Aluminium, anodised, barrel tower bolts of extruded section all as specified & directed.

S&F in repairs floor door stopper of aluminium alloy body and tongue,anodised,with hard drawn steel spring of 140 mm size with vulcanised rubber piece. complete all as specified and as directed by Engineer-in-Charge

Supply and fix 3 ways sliding anodized aluminium glazed window shutter with frame with the following specification all as specified & directed. (a) Window frame 3 track of size 95mmx25mmx1.5mm thick (b) Stiles and rails of size 35mmx25mmx1.5mm (c) 35mmx35x1.5mm T section mullion (d) PVC gasket with 4mm thick tinted glass, incl. aluminium handles with necessary locking arrangement for 02 Nos glazed shutter (e) Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire stapples incl. aluminium handles with necessary locking arrangement for 01 No gauzed shutter Note : Measurement to be taken as overall width and height of window. No shutter or frame to be measured separately. All necessary accessories including tinted glass and stainless steel wire cloth required for assembling and fixing window at proper place complete are deemed to be inclusive.

Supply and fix 2 way sliding anodized aluminium glazed ventilator shutter with frame consists of following specification all as specified & directed. (a) Ventilator frame 2 track of size 60mmx25mmx1.5mm thick (b) Stiles and rails of size 35mmx25mmx1.5mm (c) 35mmx35x1.5mm T section mullion (d) PVC gasket with 4mm thick tinted glass, incl. aluminium handles with necessary locking arrangement Note : Measurement to be taken as overall width and height of ventilator. No shutter or frame to be measured separately. All necessary accessories including tinted glass required for assembling and fixing window at proper place complete are deemed to be inclusive.

Providing & fixing false ceiling with semi perforated 12 mm thick micro tegular edged of 10 mm thick square eadge at all heights with GRG (glass fiber reinforced Gypsum ) false ceiling tiles of size 595/X595 of approved texture design and patter having moisture contain less than 2%, humidity resistance of 99%, NCR 0.50 to 0.75 as per IS 8225, 1987, non combustible as per BS 475 ( Part -IV1970 and light code description unit rate No 429 SUB HEAD 26.0 NEW TECHNOLOGIES AND MATERIAL reflectance of 85 % minimum to laid in true horizontal level suspended on interlocking metal T grid of hot dipped galvanized iron section of 0.33 mm thick ( galvanized @ 120 gms per sqm including both side comprising of main T runner of size 15X 32 mm of length of 3000 mm , cross T of size 15 X 32 mm of length 1200 mm and secondary intermediate crass T of size 15 X 32 of length of 600 mm to form grid module of size 600 X 600 mm suspended from ceiling using galvanized metal sheet item (galvanized @ 80 per sqm ie 50 mm long 8 mm outer dia meter M-6 , fasteners , 6 mm dia fully threaded hanger rod up to 1000 mm length and L shape level adjusters of size 85 X 25 galvanized iron perimeter wall angle of size 24 X24 X 0.40 mm of length 3000 mm to be fixed on perimeter of wall / partition with the help of plastic rawl pluhs at 450 mm centre to centre and 40 mm long dry wall screw . The work shall be carried out as per specification drg and as per direction of Engr-in-Charge.

Material and labour for preparation of new or previously un-treated steel or iron surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed.

Material and labour for providing PCC (1:3:6) type C1 using 40 mm graded aggregate as Plinth protection / Path finished the surface even & smooth with out using extra cement all as specified and directed.

S/F mild steel,chromium plated curtain rods with brackets, including fixing stops,rollers bracket etc with harrison rails complete all as specified and directed by Engr-in-Charge

S & F in repairs for 4mm dia GI wire fixed to both ends of wall by means of necessary fastening bolts or T-shape nut & bolt for hold the wire complete all as specified & directed.

M& L for forming Construction joint 30mm deep x 10mm wide filled with sealing compound grade 'A' complete all as specified and directed by Engr-in-Charge

E and M Division Items

Dismantling cross-arm of M.S channel or angle sections etc. Complete and setting aside for re-use witin 50 m. All as specified ans as directed.

Dismantling of ACSR or AAC conductor. All as specified and as directed.

Dismantling of unserviceable XLPE LT Cable of any size /Type all as specified and as directed

Taking down old unserviceable junction boxes of any size/type.

M&L for point wiring with two single core 1.5 Sq.mm size multistranded FRLS copper conductor PVC insulated cables and one single core 1.5 Sq.mm size green colour PVC insulated,multistranded copper conductor PVC cable as earth continuity conductor,1100 volts grade, complete drawn in and including PVC Non metatilicconcealed Conduit and conduit accessories,confirming to IS Specifications,concealed in wall, fixing on ceiling /trusses with suitable clamps , screws etc, including 1.22 mm thick MS terminal boxes with 3 mm thick plastic laminated sheet top cover fixed with cadmium plated iron screws for mounting switches, sockets, fan regulators etc.,including connecting up and testing , all as specified and as directed for (a) One light point controlled by one switch.

M&L for point wiring with two single core 1.5 Sq.mm size multistranded FRLS copper conductor PVC insulated cables and one single core 1.5 Sq.mm size green colour PVC insulated,multistranded copper conductor PVC cable as earth continuity conductor,1100 volts grade, complete drawn in and including PVC Non metatilicconcealed Conduit and conduit accessories,confirming to IS Specifications,concealed in wall, fixing on ceiling /trusses with suitable clamps , screws etc, including 1.22 mm thick MS terminal boxes with 3 mm thick plastic laminated sheet top cover fixed with cadmium plated iron screws for mounting switches, sockets, fan regulators etc.,including connecting up and testing , all as specified and as directed for (b) One fan/ exhaust fan point controlled by one switch.

M&L for point wiring with two single core 1.5 Sq.mm size multistranded FRLS copper conductor PVC insulated cables and one single core 1.5 Sq.mm size green colour PVC insulated,multistranded copper conductor PVC cable as earth continuity conductor,1100 volts grade, complete drawn in and including PVC Non metatilicconcealed Conduit and conduit accessories,confirming to IS Specifications,concealed in wall, fixing on ceiling /trusses with suitable clamps , screws etc, including 1.22 mm thick MS terminal boxes with 3 mm thick plastic laminated sheet top cover fixed with cadmium plated iron screws for mounting switches, sockets, fan regulators etc.,including connecting up and testing , all as specified and as directed for (c) One switch socket out let point 5 Amps on independent board

M&L for point wiring with two single core 1.5 Sq.mm size multistranded FRLS copper conductor PVC insulated cables and one single core 1.5 Sq.mm size green colour PVC insulated,multistranded copper conductor PVC cable as earth continuity conductor,1100 volts grade, complete drawn in and including PVC Non metatilicconcealed Conduit and conduit accessories,confirming to IS Specifications,concealed in wall, fixing on ceiling /trusses with suitable clamps , screws etc, including 1.22 mm thick MS terminal boxes with 3 mm thick plastic laminated sheet top cover fixed with cadmium plated iron screws for mounting switches, sockets, fan regulators etc.,including connecting up and testing , all as specified and as directed for (d) One switch socket out let point 5 Amps on same board

M&L for point wiring with two single core 4.0 Sq.mm size multistranded FRLS copper conductor PVC insulated cables and one single core 4.0 Sq.mm size green colour PVC insulated,multistranded copper conductor PVC cable as earth continuity conductor,1100 volts grade, complete drawn in and including PVC Non metatilicconcealed Conduit and conduit accessories,confirming to IS Specifications,concealed in wall, fixing on ceiling /trusses with suitable clamps , screws etc, including 1.22 mm thick MS terminal boxes with 3 mm thick plastic laminated sheet top cover fixed with cadmium plated iron screws for mounting switches, sockets, fan regulators etc.,including connecting up and testing complete all as specified and as directed for one 3 pin 15 Amp switch socket outlet

Supply and fixing for ceiling rose surface bakelite 65 x 50 mm three terminal complete all as specified and directed.

Supply and fixing lamp holder insulated body with back plate for batten fitting including necessary connection all as dirtected

Supply and fixing powder coated sheet metal enclosures DB, double door, single pole and neutral 8 way 240 Volt fitted with bus bar, DIN channel, neutral link and incoming contact.

Supply and fixing MCB SPN 6-32 Amps 240 volts complete all as specified and directed.

Supply and fixing MCB SP 6 Amps to 32 Amps 230 Volt complete all as specified and directed.

Supply and fixing switch piano flush type 5 Amp single pole, one way complete all as specified and directed.

Supply and fixing socket outlet 5 pin 5 Amps, flush type complete all as specified and directed.

Supply and fixing Socket outlet combination 2 in 1 3 pin 6 and 16 amp flush type universal complete all as specified and directed.

Supply and fixing Socket outlet combination 2 in 1 3 pin 6 flush type universal complete all as specified and directed.

S&F surface mounting batten tube light fitting, integrated polycarbonate LED channel with white acrylic cover complete suitable for and including lamp LED 1x20 Watt,(4 feet) fixed properly on wall surface and connecting complete from ceilling rose to fitting by three core copper conductor cable of overall sheathed size 2.5 Sqmm which shall be passed through PVC flexible conduit all as directed.

S&F building security light LED fitting 25/35 watt 230V AC outdoor type with high pressure die cast aluminum housing and heat resistant , epoxy powder coated dark graphite grey colour finish and prismatic polycarbonate cover with individual LED lences suitable for including lamp LED 25/35 watt, fixed / connect properly at directed location on building with IP 65/66 protection complete

Supply and fixing bracket for street light fittings of any size made out of GI pipe medium grade 25/32 mm dia 1.25 mtr length bend to required size and shape including provision of clamps and fittings in position and two coat of aluminum paint over a coat of red oxide primer all as specified and directed including taking down old bracket.

Taking down old fan and S&F Ceiling fan 1200mm sweep single phase 230 volts AC, min air delivery 210 CFM with service valve 6.00 BEE 5 star rating with brushless direct current motor (BLDC) with blade ,down roads electronic regulator and complete accessories complete fixed properly on wall surface with the provisioning of suitable sizes of rag bolts, nuts, washer and to connect by using cable PVC insulated copper stranded conductor of size 2.5 Sqmm 3 core and overall PVC sheathed which shall be passed through PVC flexible conduit of length not exceeding 0.50 mtr all as reqd and as directed by Engr-in-Charge.Note:- Taking down Old Ceiling fan deposit to AGE Vairengte E/M Store (not in Schedule of Credit)

M & L for building earthing complete with galvanised steel earth plate electrode 60 x 60x 6mm burried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edged of the plate not less than 1.5 mtr below normal ground level, connected to galavanised iron earth lead by means of bolt, nut, check nut and washer of galavanised iron wire 4mm as earthing lead as shown in Electrical Plate No 3 of SSR Part I connected to earthing test point all as specified or indicated including testing on completion including necessary excavation and earth work in hard/dence soil, earth pit in PCC 1:3:6 type C1 using 20mm stone aggreate, funnel, 20mm dia GI medium grade water pipe, 15mm dia GI light grade earth lead protection pipe, CI frame and cover, wire, copper lugs, wire mesh, charcoal or coke and common salt in alterative layer all around the earth electrode compacted thickness 15 cm including excavation and earth work pit cover including disposal of surplus soil to a distance not excessding 50m, complete testing on completion all complete as shown in electrical plate No 3 of SSR Part I 2009 all as directed by Engr-in-Charge

M&L for Fan hook fabricatedwith MS Flat 25X6mm 350mmlong 02 nos bend to shapedrilled with holes and MS nut, boltsandwasher of required as per side with one coatof primer and twocoatof paints as per site complete as per direction by Engr-in-Charge.

Excavating in trenches, n exec 1.5 m wide and n exec 1.5 m depth , for foundation ,etc or for shafts ,wells, cesspits, manholes, pier holes ,etc n exec 10 sq m on plain and n exec 1.5 m in depth and getting out soft or complete all as specified and directed by Engr-in-Chargeloose soil.

Returning,filling in including spreading ,levelling ,watering and well ramming in layers not exec 25 cm complete all as specified and directed by Engr-in-Charge

Removing excavated material n exec 50 m and depositing where directed ar a level n exec 1.5 m above starting point complete all as specified and directed by Engr-in-Charge

Material and labour for bricks sub-class 'B' laid in trenches for cable protection all as directed.

Material and labour for sand filling in trenches for cushioning of cable complete all as specified and directed.

M&L for PCC (1:2:4) type B2 (using 40mm graded stone as in PCC foundation complete all as specified and directed by Engr-in-Charge

M&L for PCC (1:3:6) type C-1, using 20 mm graded stone aggregate as in coping/collar for poles including necessary form work and finished to exposed surface even and fair without using extra cement complete all as specified and directed by Engr-in-Charge

Supply and fix DK thermoplastic cable junction boxes IP 65 with of size 260x210x116 of metric knockout for cable entry weather proof for outdoor installation and including glands and with 4 terminal for terminating one incoming and outgoing UG cable of size 16/35 sq mm 2/4 core and fixed to psc/steel poles by means of suitable size of clamps with nut and bolts and includin provn for fixing of one single pole MCB and MCB SPN 6-32 Amps 10 KA, 'B' series -01 no. inside the box complete all as specified and directed by Engr-in-Charge

Supply & fixing LED street light fitting 90 W 230 V AC Outdoor type with high pressure die cast aluminium housing and heat resistant complete with driver, lamp bracket with impact and corrossion resistant including thermal management in multiple optics complete with IP 65/66 protection complete.

S &F Moon (Opal) 9 W Decorative gate light made up of high grade unbreakable polycarbonate material suitable for 9 watt LED Bulb.all as specified and directed by Engr-in-Charge.

M & L taking down existing worn out GI brackets from pole and supply and fixing GI pipe bracket made out of 40mm dia GI pipe (light grade of length 1.5 meter) bent to the required shape for holding the fitting with proper angle including providing two pair of MS flat iron clamps of size 40mm x 6mm of required length duly drilled for bolt holes with required nuts, bolts and washers of suitable size, including applying two coats of aluminium paint over a coat of red oxide primer to clamps after perparation of surfaces complete all as specified and as directed.

S&F cable 2.5 sqmm PVC insulated FRLS multi standard copper conductor for connection from conductor to street light fitting complete all as specified and directed by Engr-in-Charge

Supply ,laying and testing in trenches or fixing on wall or passing through pipe 1100 volts grade heavy duty cable XLPE Insulated multi stranded aluminium conductor cross section area 16 sqmm 4.0 core served with an inner sheathing of PVC tape armoured with galvanised steel wire or strip and over PVC sheathed complete as per specification properly clamps on wall and connection at end point with all legs ,glands etc complete as per direction by Engr-in-Charge.

Supply fixing & testing of XLPE insulated, screened, PVC bedded,galvanised steel strip or wire armoured,electric power cables (heavyduty) with aluminium conductor, 1100volts, grade cross sectional area 50 sqmm 3-1/2 core complete all as specified and directed by Engr-in-Charge

Supply,fixing & testing of XLPE insulated, screened, PVC bedded,galvanised steel strip or wire armoured,electric power cables (heavyduty) with aluminium conductor, 1100volts, grade cross sectional area 16 sqmm 4.0 core complete all as specified and directed by Engr-in-Charge

Supply ,fixing & testing of XLPE insulated, screened, PVC bedded,galvanised steel strip or wire armoured,electric power cables (heavyduty) with aluminium conductor, 1100volts, grade cross sectional area 25 sqmm 3-1/2 core complete all as specified and directed by Engr-in-Charge

Supply laying and fixing 32mm medium grade, galvanised iron water tubes with screwed socket joint together with and including all GI fittings connection on waal or floor with clamps digging etc as per site requirement as per Engr-in-Charge

Supply laying and fixing 25mm medium grade, galvanised iron water tubes with screwed socket joint together with and including all GI fittings connection on waal or floor with clamps digging etc as per site requirement as per Engr-in-Charge

Supply & laying GI Tubes 40mm dia, 'light grade', galvanised, with all fitting; laid in trenches complete all as specified and directed by Engr-in-Charge

Supply, Install, testing and commisioning of CPRI approved outdoor type LT feeder piller box of suitable size recommended by CPRI approved manufacturer cubical floor mounted type factory made totally enclosed, dust ad vermin proof made out of 3.15 mm thick MS sheet duly painted with powder coated both side in and out, having proper locking arrangment in both front and rear side aluminium bus bar of 400 amps rating duly drilled holes for connections and mounted on epoxy based post insulators for 3 phase, 4 wire, 16 Sqqmm, 500 volts, 50 HZ AC supply, hibling , cable entry boxes, cable gland incl iron angle frame (bottom portion of the panel), grouted by using foundation 1:2:4 type C1 with 20 mm graded stone aggregates totally tested as per IEC 61439-I with the following: Incoming : (a) MCCB 250 Amps, 4 pole, 25 KA, 415V - 01 Nos Outgoing: (a) MCCB 100 Amps, 4 pole, 16 KA, 415V - 02 Nos (b) MCB TPN 63 Amps 10KA - 02 Nos (c) Contractor 3 pole 32 amp -01 Nos (d) Toggle switch 6 amp-01 Nos (e) Timer(analog) with battery backup-01 Nos (f) Overload relay 2/3.5A-01 Nos (g) Phase indicator lamps (RYB) set of 3 - 01 Set Note : (a) Excavation for grouting and PCC foundation for LT Panel shall be deemed incl in quated rate.

Supply, installation, testing and commissioning LT Feeder pillar box CPRI Tested of Size 1000x800X500 mm suitable for 3 phase 415 Volts of suitable size out door made out 3.15mm thick CRCA sheet with angle iron frame of size 50x50x6mm cubical type complete with Aluminium bus bar 400Amp to accomodated to the following. INCOMING (a) MCCB 4 pole 250 Amp 25 KA Icu = 100%Ics (Make: ABB/L&T/Legrand/Schnider/ SIEMENS/ Indoasian) - 01 No - 01 No. (b) LED indicating lamp R-Y-B - 03 Nos. OUTGOING (a) Through Bus Bar

M & L for earthing complete with galvanized steel earth plate electrode 600mm x 600mm x 6 mm thick buried directly in ground vertically to a depth not less than 2.25 mtr deep below GL with top edge of the plate not less than 1.5 mtr below normal GL and connected to earth plate surrounded by 15 cm thick packed layers of charcoal dust and common salt and connected to earth lead GI wire 4mm dia by means of bolts, nuts, check nuts and washers of galvd iron or steel and thimbles and other end of the earth wire connected to DB and protected by galvd iron or steel pipe light grade 15 mm bore and water pipe 20 mm bore GI light grade with funnel and wire mesh, including all necessary excavation and earth and all shown in electrical plate No 5 of MES schedule Part I of 1991 complete all as specified and directed by Engr-in-Charge

Supply & fixing Saucer nextgen Highway light 120 W Energy saving, environmental friendly, long life, exclusive innovative die-cast aluminium IP66 flood light, suitable for highlighting architectural facade and general purpose lighting complete all as specified and directed by Engr-in-Charge. Cat No. SAUCERGENXPROHBP120WLED757P90DBOLTG of Havells or equivalent to Bajaj/Surya/Philips

Supply & fixing Rigid non-metallic 20 mm PVC conduit exclusive of boxes 9junction/terminal but inclusive of all tees,bends,elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock. Nuts, saddles, pipe hooks complete all as specified and directed by Engr-in-Charge

Materials & labour for submain wiring with two single core 2.5 sqmm (FRLS) copper conductor PVC unsheathed cable medium grade including PVC conduit (appropriate size) concealed in wall for sub main connection including 2.5 Sqmm PVC insulated multistranded unsheathed copper conductor used as a earth wire to common earth and connection to earth dolly complete all as specified and directed by Engr-in-Charge Notes: (i) 02 runs of 2.5sqmm main cable, 1 run of earth conductors of 2.5 sqmm and 1 run of PVC conduit dia 25mm shall be measured as one length (ii) Separate casing shall be used for each sub-main wiring circuit irrespective of numbers of wire (iii) The minimum size of conduit (appropriate size) concealed shall be as stipulated, however higher sizes shall be used as per number of cables passing through. The Engineer-in-charge shall ensure for proper size of casing as per requirement at site

Please Enable Macros to View BoQ information