Construction of Directorate of Police Communication and Technical Services Centre at Maandal Bhangrotu Teshil Balh Distt Mandi HP SH Construction of Admn Block including internal WS SI development of site and Co 10000 litres capacity RWHT

Amount

Cutting in earth work in all heights / depths and in all kinds of soil such as kankar, moorum, shingle and decomposed or soft rock, hard rock i.e. their intermediate classification and chiselling / wedging out of rock including saturated soils and filling in embankments etc. where necessary and disposal of all excavated un-serviceable material through mechanical transportation and cost of dumping charges in all leads and lifts. Any damage to the private / public property during execution will be restored by the contractor whatsoever the nature of the same may be.The serviceable materials will be stacked in specified dimensions in all leads and lifts as per the direction of the Engineer -in- charge.

Excavation in foundations, trenches etc., in earth work, in all kind of soils such as pick work,jumper work and chiselling/wedging out of hard or soft rock up to all depths stacking the excavated soil not more then 3 meteres clear from the edge of excavation and then returning the stacked soil in 15 cms layers,when required in to plinths, sides of foundations etc. consolidating each deposited layer by ramming and watering and then disposing off all surplus excavated earth as directed by the Engineer -in-charge.

Excavation in earth work in all kinds of soils such as pirk work, juimper work and chiselling/wedging out of hard or soft rock and disposal of all excavated earth up to any leads and lifts disposed earth to be levelled and neatly dressed as directed by the Engineer-in-chargeincluding carriage of material in all leads and lifts.

Excavation in drains and channels etc. in earth work in all kinds of soil such as pick work, jumper work and chiseling/wedging out of hard or soft rock up to all heights including dressing of sides and bed and disposing of excavated earth up to all leads and lifts and disposed earth to be levelled and neatly dressed including carriage of material in all leads and lifts.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete including carriage of material in all leads & lifts

Providing form work with steel plates 3.15mm.thick welded with angle iron in frame 30x30x5mm. so as to give a fair finish including centring, shuutering,strutting and propping etc with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 Mtrs. and removal of the same for insitu-reinforced concrete & plain concrete work including carriage of material in all leads & lifts

Foundation , Footings basis of columns etc. and mass concrete.

Flat surfaces such as soffits of suspended floors, roofs, landings and the like.;-Floors etc.upto 200mm. In thickness

Columns, pillars, posts and struts Square, rectangular or polygonal in plan.

Beams, cantilever, girders and lintels. Sides and soffits of beams, beam haunchings, cantilevers,bressumers and lintels not exceeding 1 Mtr. in depth in all heights from floor.

Stair cases with sloping or stepped soffits excluding landing

Vertical surfaces such as walls (any thickness) partitions and the like including attached pillasters buttresses, plinth and string courses and the like including carriage of material in all leads & lifts.

Edges of slabs and breaks in floors and walls;-Under 20 cm. wide.

Providing and laying cement concrete 1:6:12 (1 cement:6 sand : 12 graded stone aggregate 40 mm nominal size) and curing complete excluding cost of centring and shuttering including carriage of material in all leads & lifts.;-Foundation and plinth

Providing and laying cement concrete 1:4:8 (1 cement:4 sand:8 graded stone aggregate 40mm nominal size) and curing complete excluding cost of form work including carriage of material in all leads & lifts.;-Foundation and plinth

Providing and Laying cement concrete 1:5:10 with 15% plams and curing complete including the cost of farmwork for plain/reinforced concrete in retaining walls, breast walls, the size of plum should be 150 to 300 mm as per drawing and HP.PWD technical specifications including carriage of material in all leads & lifts.

Providing and laying cement concrete having strength of M-20 mixed design aggregate mechanically mixed and vibrated and curing complete excluiding cost of form work and reinforcement for reinforced concrete work including carriage of material in all leads and lifts.

Foundations,footings bases of columns and the like and mass concrete.

Walls (any thickness but not less than 0.10 metre thickness) including attached pilasters buttersses , plinth and string courses etc. from top of foundation upto floor two level

Suspended Floor roofs , landing and shelves and their support balconies,beams,girders, bressumers and contilever upto floorall level

Columns, pillars, posts and struts, Square, rectangular or polygonal in plan.

Stair cases (except spiral stair cases) excluding landing but including preparing of the surface and finishing of nosing upto floor all level.

Providing and laying upto first floor two level reinforced cement concrete 1:2:4 (1 cement : 2 Sand :4 graded stone aggregate 20mm nominal size) to give a smooth and even surface including centring and shuttering etc. but excluding cost of reinforcement in including carriage of material in all leads and lifts.;-Moulding as in cornices, window sills etc. not xceeding 15cm. In girth.

Providing & laying cement concrete having strength of M-20 design mixed aggregate mechanically mixed and vibrated for reinforced concrete in chajjas upto any thickness upto all heights i/c finishing the exposed surfaces with cement mortar 1:3 (1 cement : 3 sand) to give a smooth and even surface i/c centering/form work and curing complete but excluding cost of reinforcement including carriage of material in all leads and lifts.

Providing tor steel reinforcement for RCC work including bending, binding and placing in position complete including cost of binding wire up to all flooe level including carriage of material in all leads and lifts.

Applying cement slurry on R.C.C. slab or cement concrete work using 2.75 kg. of cement per sq.metre of floor area before laying cement concrete flooring including roughening, cleaning of the concrete surfaces complete including carriage of material in all leads and lifts.

Providing and laying cement concrete 1:8:16 (1cement: 8sand:16graded stone aggregate 20mm. nominal size) and curing complete on slab and floor excluding the cost of form work screed laid under flooring.including carriage of material in all leads and lifts.

Applying a coat of hot bitumen (mexphalt 80/100 or equivalent) using 1.70 kg. per square metre on damp proof course after cleaning the surface with a piece of cloth lightly soaked with kerosene oil including carriage of material in all leads & lifts.

Brick work using Second Class common burnt clay building bricks in Super-structure above plinth level upto all floor level including carriage of material in all leads and lifts. Cement Mortar 1:6 (1 Cement : 6 Sand)

Half brick masonry using Second Class Bricks in common burnt clay building bricks in superstructure including carriage of material in all leads and lifts. Cement Mortar 1:4 (1 cement:4 sand)

Random rubble masonry/polygonal rubble masonry (uncoursed/brought to courses) with hard stones of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (1 cement :6 sand : 12 graded stone aggregate 20mm nominal size) at plinth level. including carriage of material in all leads and lifts;-Cement Mortar 1:6(1 cement:6 sand)

Boulder filling dry hand packed tightly as in and under floor including watering,ramming and consolidating complete including carriage of material in all leads and lifts.

Stone filling behind retaining walls.including carriage of material in all leads and lifts.

Providing weapholes in brick masonry / stone masonry /plain reinforced concrete abutment, wing wall, return wall with 100 mm dia PVC pipe extending through the full with of the structures with slop of 1(v):20(H) towards drawing face complete as per drawing and technical specification clauses 614, 709, 1204.3. including carriage of material in all leads and lifts.

Providing & fixing door frame of NCL, SECOOLAR abr carried from all formed section made of galvanised steel power coated (basic steel as per IS 513 D) quality galvanished as per 277 with zinc of 120 gms/ sqm powder coated with pure polyster power up to 50-60 with microns thick the overall size should be 125 mm x 60mm for double rebate including fixing in position as per the direction of Engineer-In-Charge including carriage of material within all leads & lifts.

Providing & fixing door frame of NCL, SECOOLAR abr carried from all formed section made of galvanised steel power coated (basic steel as per IS 513 D) quality galvanished as per 277 with zinc of 120 gms/ sqm powder coated with pure polyster power up to 50-60 with microns thick the overall size should be 150 mm x 60mm for single rebate including fixing in position as per the direction of Engineer-In-Charge including carriage of material within all leads & lifts.

Providing and fixing 40 mm thick frame with 12mm both side prelaminated board bwp phenol exterior /interior grade MATT finish flush door shutters including stainless steel bright finished butt hinges with necessary screws TREND MAKE DOOR SKIN MODEL NO. 247 including carriage of material in all leads and lifts :- Confirming to BIS Specification as per HIMUDA architectural drgs.

Providing and fixing steel glazed door window and ventilated of ECO 4000 series of NCL SECOOLOR colour coeted standard rolled sections size cuter frame 72x 55mm thick mullion 72x 50x 0.58 style frame 46x 20mmx 0.58mm thick section for glass bead sholud be of 12mmx 12mm x o.58mm thick section for mesh 40x 20x 58mm fixing should be 18mm x 0.6mm x .58mm thickness. the sectionof sash panel openable shutter shall be 55mm x20mm x 0.58mm(107) each glazed shutter should be provide with one set of SSP/VOT hinges make handle with receiver glazed shutter and fixed glass portion should be provided with 4mm thick glass window should be provided with grill made of 10mm MS square bar welded to 6mm x12mm ITS Flat Distance Between Bars should not be more 150mm centre to centre total grill unit should be fixed to window frame with screws and embeded in cement concrete block 15cm x 10cm x 10cm size of1:3:6 (1 cement: 3 sand:6 aggregate 20mm nominal size wooden plugs screws or plugs and fixing clips with bolts and nuts as required and non filling including fixing of glass with gaskit clips as per architectural specification and as per the direction of Engineer-In- Charge including carriage of material with in all leads & lifts.

Providing and fixing wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85 G. with wire of dia 0.56 mm for doors windows and clerestorey windows and chamfered edged beading 20X12mm including bright finished black enamelled iron hinges with necessary screws including carriage of material in all leads and lifts. 40mm thick 2nd class deodar wood.

Providing and fixing M.S. grills of required patterns in wooden frames of windows etc. with M.S. Flats, square or round bars with round headed bolts and nuts or by screws including carriage of material in all leads and lifts.

Providing and fixing 19mm thick commercial Board water proof shutters for cup boards including fixing with nickel plated piano hinges with screws etc complete including carriage of material in all leads and lifts.

Providing and fixing 19mm thick water proof commercial board in shelves for cup board with butt joints and fixing with nails & screws etc. complete including carriage of material in all leads and lifts.

Providing and fixing 1.00mm thick coloured or plain lamination sheet (sunmica) on boards/ply wood sheet with approved adhesive and nails etc. complete. Including carriage of material in all leads and lifts .

Providing and fixing 4mm thick water proof kit ply of standard quality ISI mark and approved shade and colour in wall linning including mitering at junction, butt jointing and nails complete (frame work for base to be measured and paid for separately) including carriage of material in all leads and lifts .

Providing and fixing 65x35mm special quality chromium plated brass cup board lock with six leavers including necessary screws etc. complete (Indian make) including carriage of material in all leads and lifts .

Providing and fixing oxidized aluminium sliding door bolts with nuts and screws etc. complete including carriage of material in all leads and lifts.

Providing and fixing oxidised aluminium tower bolts (barrel type) with necessary screws etc. complete including carriage of material in all leads and lifts.

Providing and fixing oxidized aluminium handles with the necessary screws etc. complete.including carriage of material in all leads and lifts.

Providing and fixing oxidized M.S. hooks and eyes including carriage of material in all leads and lifts ;-150mm

Providing and fixing 100mm bright finished brass floor door stopper with rubber cushion screws etc. to suit shutter thickness complete including carriage of material in all leads and lifts.

Providing and fixing bright finished brass handles with the necessary screws etc. complete.including carriage of material in all leads and lifts. 125mm

Providing and laying Duro stone vetrified tiles any size /coloured or of approved shade in flooring, treads of steps and landing laid on a bed of 12mm thick cement mortar 1:3 (1 cement : 3 sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete including carriage of material in all leads and lifts.

Providing and laying Duro stone vetrified tiles any size/coloured of required shade in skirting risers of steps and dados on12mm thick cement mortar 1:3 (1cement : 3 sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete including carriage of material in all leads and lifts

Providing and fixing 10mm thick anti skid water proof stain and impect resistent heavy duty vetrified tiles manufactured of approved shade and colour in flooring, treads of steps and landings laid over 12mm thick cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete including carriage of material in all leads and lifts.

Digital tiles in skirting risers of steps and dado 12 mm thick cement mortar 1:3 (1 cement :3 sand) and jointed with cement slurry including carriage of material in all leads and lifts

Providing and laying granite stone in flooring 20mm (average) thickness basae of cement mortar 1:3(1 cement:3 Sand ) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone including rubbing and polishing complete including carriage of material in all leads and lifts;-20mm thick.

50mm thick Cement concrete flooring 1:2:4 (1 cement : 2 sand:4 graded stone aggregate 20 mm nominal size) laid in one layer finished with a floating coat of neat Cement including carriage of material in all leads and lifts.

Providing and laying heavy duty precast cement conrete inter locking paver blocks vibro compacted upto M- 50 grade i/c border or kurb block grey or coloured over sub-base of concrete with 25mm thick average thickness of cement mortar 1:4 (1 cement : 4 sand) laid over and jointed with neat cement slurry mixed with pigment to match the shade of blocks i/c curing rubbing & polishing complete (Sub base concrete floor to be paid for separatelly) including carriage of material in all leads and lifts ;- 60mm thick inter locking block.

Providing and fixing on wall faces PVC (D-Plast) for rain water pipes of working pressure not less than 4.5 kg/sqm including filling the joints with approved adhesive complete including carriage of material in all leads and lifts;- 150mm dia pipes

Providing and fixing m.s.holder bat clamps of approved design to C.I. or S.C.I pipes embeded in and including cement concrete blocks 10 x10x10 cm of 1:2:4:mix (1 cement 2 sand 4 stone graded stone aggregate 20 mm nominal size) and cost of cutting holes and making good the wal etcincluding carriage of material in all leads and lifts;-150 mm diametre for C.I./PVC pipe

Providing and fixing on wall faces PVC (D-Plast) accessories for rain water pipes including filling the joints with approved adhesive complete including carriage of material in all leads and lifts

PVC Plain bend 150mm dia

PVC shoe 150mm dia

Providing and fixing 0.60mm thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia metre with prepainted limpet and rubber washers complete with all accesoriees as required as per the direction of Engineer-in-charge

Providing and fixing ridges or hips 60 cm overall with 0.60mm thick prepainted steel sheets in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts & nuts 6mm dia & prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer in Charges including carriage of material in all leads and lifts.

Providing and fixing valley 60 cm overall 0.60mm thick prepainted steel sheet in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia with prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer-in-charge including carriage of material in all leads and lifts.

Providing and fixing 15 cm. wide 45 cm. overall semicircular plain G.I. sheetgutter with iron brackets 40x3mm size bolts and nuts and washers etc. including making necessary conections with rain water pipe complete as per design including carriage of material in all leads and lifts.;-0.63mm thick sheet.

Providing and fixing M.S. BP Sheet 1.66mm to 2mm thick in eaves board/facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-charge (Base members of steel work shall be measured & paid separtely) including carriage of material in all leads and lifts

Providing and fixing stainless steel railing mark-36 pipe size top 2" pipe, post pipe 1" and 3' height in staircases including necessary fitting and position as per design approved by the Engineer-in-Charge including carriage of material in all leads and lifts.

Steel work welded in built up sections,trusses and framed work,including cutting ,hoisting ,fixing in position and applying a priming coat of red lead paint including carriage of material in all leads and lifts.

In beams joists channels ,angles , tee ,flats with connecting plates or angle cleats as in main and cross beams,hip and jack rafters,purlins connected to common rafters and the like.

In gratings framed guard bars,ladders,railling,brackets and similar works.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops,dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete including carriage of material in all leads and lifts.

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its quarlied on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth complete including carriage of material in all leads and lifts.

Applying priming coat over new steel & other metal surfaces after & including preparing the surface by thoroughly cleaning oil grease dirt and other foreign matter and scoured with wire brushes fine steel wool scrapers and sand paper complete including carriage of material in all leads and lifts.;-With ready mixed priming paint brushing red lead,Red-oxide/zinc oxide chrome.

Painting two coats (excluding priming coat on new steel and other metal surfaces eith enamel paint brushin to give an even shade including cleaning the surface of all dirt,dust and other foregin matters including carriage of material in all leads and lifts;-Enamel white paint other than white.

Applying priming coat over new wood and wood based surfaces after and including prepering the surface by thoroughly cleaning oil,grease,dirt and other foreign matter) sand papering and knotting including carriage of material in all leads and lifts;-Ready mixed paint brushing wood primer pink

Painting two coats(excluding priming coat) on new wood and wood based surface with enamel paint to give an even shade including cleaning the surface of dirt,dust and other foreign matter,sand papering & stoping including carriage of material in all leads and lifts;-With white enamel paint other than white

6mm Cement plaster to ceiling including carriage of material in all leads and lifts; - In Cement mortar 1:3(1Cement:3 Sand)

15mm cement plaster in single coat on fair side of brick/concrete/stone walls for interior plastering upto floor two level including arrises,internal rounded angles, chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth including carriage of material in all leads and lifts;-Cement Mortar 1:6 (1 cement:6 sand).

20mm Cement plaster in single coat on rough side of brick/stone masonry forinterior plastering upto floor two level including arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth including carriage of material in all leads and lifts;-

Cement Mortar 1:6 (1 Cement :6 sand).

Cement Mortar 1:3 (1 Cement :3 sand).

Distempering (two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth. Priming coat with distemper primer including carriage of material in all leads and lifts.

Distempering (two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated on ceiling and/or sloping roofs. surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth. Priming coat with distemper primer including carriage of material in all leads and lifts.

Providing plinth protection 50mm thick in cement concrete 1:3:6 (1 Cement : 3 Sand : 6 Graded stone aggregated 20mm nominal size)including carriage of material in all leads and lifts.

Providing under layer for plinth protection of 75mm thick (unconsolidated) bed dry brick/stone aggregated 40mm nominal size with rammed and consolidated and grouted with fine sand including preparation of ground including carriage of material in all leads and lifts.

Brick edging (Brick laid on edge) to plinth protection with bricks including grounting with cement mortar 1:4 (1 Cement : 4 Sand).;-With bricks size 22.9cmx11.2cm x7cm including carriage of material in all leads and lifts.

Constructing Course rubble hammer dressed 'U' shape open surface drain with side wall.15x22 cm in cement mortar 1:6 (1 Cement : 6 Sand) and inside plastring with cement plaster 1:3 (1 Cement:3 Sand) including earth work and laying 10 cm cement concrete in 1:5:10 (1 Cement : 5 Sand : 10 graded stone aggregate) of 40 mm nominal size) and 7.5 cm cement concrete 1:2:4 (1 Cement : 2 Sand : 4 Graded stone aggregate of 20 mm nominal size) and finished with a floating coat of neat cement complete as per standard design.) including carriage of material in all leads and lifts.

Providing chases 75mm wide 50mm deep (average size) in walls for conduit pipes and filling the same with cement concrete 1:3:6 (1 Cement : 3 Sand : 6 Graded stone aggregate 20 mm and down gauge) after the conduit pipe is laid (excluding the cost of conduit pipe)including carriage of material in all leads and lifts.

Providing and fixing to wall ceiling and floor Polyethylene- Aluminium- Polyethylene(PE-AL-PE) composit pressure pipes confirming to IS-15450, U.V. stablized with carbon black having thermal stability for hot and cold water supply, capable to withstand temprature up to 80 degree C, including all special fittings of .composite material (engineering plastic blend and brass inserts whereever required) e.g. elbows, tees, reducers, couplers and connectors etc; with clamps at 1.0 metre spacing. This includes testing of joints complete as per direction of the Engineer-In- charge, including carriage of material in all leads and lifts.

16mm outer dia.

20mm outer dia.

Providing and laying in trenches, galvanised mild steel tubes (medium grade), tube fittings (earth work in trenches to be measured and paid separately) including carriage of material in all leads and lifts:- 20mm nominal bore.

Making connection of galvanized steel distribution branch with galvanized mild steel main 20 to 40mm nominal bore by providing and fixing tee including cutting and threading the pipes complete including carriage of material in all leads and lifts.

Providing and fixing PVC water storage tank of ISI : 12701 marked, G.I. inlet and outlet connection, 15mm nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting up to all heights above ground level including carriage of material in all leads and lifts;-1000 litres net capacity tank

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete including carriage of material in all leads and lifts.

110 mm dia.

75 mm dia.

Providing and fixing PVC single equal branch with ovel access door, ISI marked insertion rubber washer 3mm thick bolts and nutscomplete including fixing with approved adhsive etc. complete including carriage of material in all leads and lifts.

110 mm dia

75 mm dia

Providing and fixing PVC door bend with oval access door, insertion rubber washer 3 mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. complete including carriage of material in all leads and lifts.

110 mm dia.

75 mm dia.

Providing and fixing PVC collars ISI marked including fixing with approved adhesive etc. complete including carriage of material in all leads and lifts.

110 mm dia.

75 mm dia.

Providing and fixing PVC clamps ISI marked of approved design with steel screws and rawal plugs etc. complete including carriage of material in all leads and lifts.

110 mm dia

75 mm dia

Providing and fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete including carriage of material in all leads and lifts;-110 mm X 75 mm..

Providing and fixing vitreous china wash down, water closet (European type W.C. pan ) with integral 'P' or 'S' trap including jointing the trap with soil pipe in cement mortar 1:1 (1 cement ; 1 sand ) Seat and cover to be measured and paid for separately) including carriage of material in all leads and lifts;- Ordinary closet

Providing and fixing PTMT coloured/ white high density polyethylene / poly propylene 10 litres capacity ( full flush) European standard control low level flushing cistern with fittings with a pair of brackets with fittings such as lead valve, syphon, 15mm nominal size PVC ball valve with polythene float, with push button, couplings for connections with inlet, outlet and over flow pipe, 40mm dia C.P. flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (overflow pipe to be measured and paid for separately) including carriage of material in all leads and lifts

Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete including carriage of material in all leads and lifts.

110 mm dia

75 mm dia

Providing and fixing stainless steel kitchen sink of approved standard ISI make with drain board and C.P. waste with C.I. or M.S. Brackets painted white including cutting holes and making good the same but excluding fitting including carriage of material in all leads and lifts;-610X5100 mm with bowl depth 200mm.

Providing & fixing consealed stop cock including carriage of material in all leads and lifts:- 15mm

Providing and fixing vitreous China bowl pattern urinal including connection the urinal with waste pipe by means of white lead mixed with chopped hemp (waste pipe to be measurred and paid for separately) including carriage of material in all leads and lifts:-Flat back type of size 430mm x 260 mm x 350 mm.

Providing and fixing C.P. brass flush pipe/spreaders for urinal with fitting such as unions, clamps etc. (all in C.P. Brass) including cutting holes and making good the same including carriage of material in all leads and lifts:-15mm nominal bore

Providing and fixing Division Plate for Urinals 600mmx300 Vitreous China including carriage of material in all leads and lifts

Providing and fixing PTMT Coloured / white automatic flushing cistern with a pair of PVC / C.I. or M.S. bracket complete with fittings including PVC syphonic apparatus, mosquito proof lid, PVC union and coupling for connections with inlet, outlet and over flow pipes including cutting holes and making good the same ( over flow pipe to be measured and paid for separately) including carriage of material in all leads and lifts ;-5 litres net capacity

Providing and fixing P.V.C connection with brass unions including carriage of material in all leads and lifts:- 300/450mm length,15mm dia

Providing and fixing stoneware gully trap grade 'A' complete with C.I grating, brick masonry chamber in cement mortar 1:5 and water tight C. I. cover with frame of 300mmx300mm size (inside) the weight of cover to be not less than 4.53kg and frame to be not less than 2.72kg including carriage of material in all leads and lifts;- Square Mouth Traps , 100mmX100mm size P or R type.

Providing and fixing vitreous China wash basin with single/double hole for pillar tap with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fittings including carriage of material in all leads and lifts.;- Flat back 550mmx400mm.

Providing and fixing vitreous China pedestal for wash basin complete recessed at the back for the reception of pipes and fittings including carriage of material in all leads and lifts.

Providing and fixing C.P. Brass waste for wash basin or sink including carriage of material in all leads and lifts;-32mm dia

Providing and fixing C.P. Brass shower rose with 15mm or 20mm inlet including carriage of material in all leads and lifts ;-150mm dia

Providing and fixing 100mm dia chromium plated grating of superior quality for floor, gully or nahani trap including carriage of material in all leads and lifts

Providing and fixing G.I./M.I Union of following sizes (where not included in the items) including carriage of material in all leads and lifts

Providing and fixing 32 mm P.V.C. waste pipe for wash basin or sink including brass check nut including carriage of material in all leads and lifts.

Providing and fixing plastic seat (Solid / Hollow type) and cover for wash down water closet with C.P. Brass hinges and rubber buffers including carriage of material in all leads and lifts;-white plastic seat and cover.

Providing and fixing 600mm x 120 mm glass shelf with C.P. Brass bracket and guard rail complete, fixed to wooden plugs with C.P. Brass screws including carriage of material in all leads and lifts

Providing and fixing 600mm x 450 mm bevelled edge mirror of superior glass mounted on 6mm thick A.C. Sheet or plywood sheet and fixed to wooden plugs with C.P. Brass screws and washers including carriage of material in all leads and lifts

Providing and fixing C.P. Brass Towel rail complete with C.P. Brass brackets fixed towooden plugs with C.P. Brass screws including carriage of material in all leads and lifts;-600mmx20mm

Providing and fixing Mixer for kitchen sink with casted swinging spout at top including carriage of material in all leads and lifts

Providing and fixing brass full way valve with wheel including carriage of material in all leads and lifts.

15mm nominal bore

20mm nominal bore

Providing and fixing chromium plated brass soap dish with C.P. Brass brackets fixed to wooden cleats with C.P. Brass screws including carriage of material in all leads and lifts

Providing and fixing C,P brass pillar tap with capastan head including carriage of material in all leads and lifts;-15mm dia

Providing and fixing C,P brass bib tap Long body with capastan head including carriage of material in all leads and lifts;-15mm dia

Providing and fixing C,P brass bib tap short body with capastan head including carriage of material in all leads and lifts;-15mm dia

Providing and fixing PTMT jet spray of approved quality and colour with one metre tube including carriage of material in all leads and lifts

Providing and fixing C.P. brass angle valve 15mm without Nuts and pipe including carriage of material in all leads and lifts

Cutting holes through existing brick work including making good the same in cement mortar 1:6 (1 cement: 6 sand) per CMs. Depth of cutting including carriage of material in all leads and lifts;-Holes upto and including 400 Sq.cm in area.

Constructing manhole with RCC top slab in 1:2:4mix(1cement:2sand :4graded stone aggregate 20mm nominal size) foundation concrete 1:4:8(1cement:4sand:8graded stone aggregate40mm nominal size) inside plastering 15mm thick with cement mortar 1:3(1cement:3sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4mix (1cement:2sand:4graded stone aggregate 20mm nominal size)finished smooth complete including curing and testing including carriage of material in all leads and lifts:

Inside size 800mm x 800mm x 500mm deep including S.F.R.C cover with frame (light duty) total weight of frame and cover to be not less then 173 kg weight of frame 103 kg weight of cover 70 kg with 230 mm thick walls of brick masonry using common burnt clay building bricks in cement mortar 1:3(1cement:3sand). including carriage of material in all leads and lifts.

Inside size 800mm x 800mm x 1000mm deep including S.F.R.C cover with frame (light duty) total weight of frame and cover to be not less then 173 kg weight of frame 103 kg weight of cover 70 kg with 230 mm thick walls of brick masonry using common burnt clay building bricks in cement mortar 1:3(1cement:3sand). including carriage of material in all leads and lifts.

Extra over item No. above for every additional depth of 0.10 metre of part thereof of Manhole. From 0.5 metre up to 1.0 metre depth including carriage of material in all leads and lifts.

Providing and laying , jointing and testing in trenches centrifugally cast spun ductile iron pipes conforming to BIS 8329-2000 (latest with up to date amendments) in a lenght of 5.50 meters class K7 with cement mortar ning in side duty ISI marked including cost of Tyton (push or joints) fitting including testing of joints and rubber gasket (S&R quality) conforming to IS-92820-1989( Earth work in trenches to be measured and paid for separetely) including carriage of material in all leads and lifts;-150mm dia

Supplying and fixing cast iron cover with frame for manhole of internal diamensions 450x610mm rectangular C.I cover (light duty) single seal pattern-I, the weight of cover and frame to be not less than 38kg. (Weight of cover 23kg and weight of frame 15kg) including carriage of material in all leads and lifts.

NARAIN DASS NAIK

CHETAN VAIDYA

RAKESH GOEL