PROVN OF HARD STANDING IN QUARTER GUARD OF CERTAIN MIL UNIT, PROVN OF SCOOTER PARKING SHED FOR CERTAIN MIL UNIT, PROVN OF INCINERATOR FOR CERTAIN MIL UNIT, PROVN OF INCINERATOR FOR CERTAIN MIL UNIT, PROVN OF TOILETS AT QUARTER GUARD OF CERTAIN MI

Amount

Demolition of cement Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level all as specidied

M&L for Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified

Surface excavation n.exc (not exceeding) 7.50 cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified

Excavation in trenches, n exc 1.5 mtr wide and n exc 1.5 mtr in depth for foundation etc. or for shafts, wells, cesspits, manholes, pier holes etc. n exc 10 Sqm on plan and n exc 1.5 mtr in depth and getting out in soft/loose soil complete all as specified

Returning filling in including spreading levelling watering and well ramming in layers not exc 25 Cm complete all as specified

Removing excavated material (soil) n exc 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified

M&L PCC (1:4:8) type D2 (using 40 mm graded stone aggregate) for fdn/ mass concrete complete all as specified

M&L for RCC Type A-1,nominal mix (1:1.5:3) (20 mm graded aggregate) in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified.

M&L RCC Type A1,nominal mix (1:1.5:3) (20 mm graded aggregate) in Columns, pillars, piers, posts and struts complete all as specified.

M&L RCC Type A1, nominal mix (1:1.5:3) (20 mm graded aggregate) in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified.

M&L RCC Type A1, nominal mix (1:1.5:3) (20 mm graded aggregate) Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified.

M&L TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified

Ditto, but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders.

M&L TMT bars 6 to 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified

Use & waste of Formwork flat rough finished to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified.

Use & waste of Formwork flat rough finished surfaces to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. complete all as specified

Use & waste of Formwork square, rectangular or plougonal rough finished surfaces to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified.

M&L for Flyash Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in cement mortor 1:6 complete all as specified

M& L for Fly ash Brickwork with sub-class `B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM (1:4) complete all as specified

Use & waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (horizontal or sloping) etc. rough finished flat surfaces complete all as specified

Material and labour rendering 20mm thick cement plaster in CM 1:4 on fair faces of brick/concrete work surfaces in two layer 10mm each layer and top layer mixed with integral water proofing compound all as per manufacturer's instruction and as specified. Make: 'Plastocrete Plus' of Sika/ 'Pidiproof LW' of Pidilite for water proofing compound. Note: (i) WPC shall be measured and paid for separately as 'Supply only'. (ii) WPC to be mixed @200ml per 50 Kg bag of cement all as manufacturers instruction.

Supply only liquid water proofing compound all as specified.

M&L 15mm thick rendering in CM 1:6 on faces of stone brickwork or concrete surface walls finished even and smooth without using extra cement complete al as specified.

M&L 15mm thick rendering in CM 1:4 on faces of stone brickwork or concrete surface walls finished even and smooth without using extra cement complete al as specified.

M&L for preparing new plastered surfaces of wall with wall care putty and applying two coat of distemper oil emulsion over a coat of primer complete all as specified.

M&L for preparation new plaster surfaces of wall and applying two coats of cement base paint complete all as specified

M&L Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc.15 cm thick, watered and rammed to a true surface all as specified .

M&L sand filling under floors or in foundations including watering and consolidation, in cable trenches over & under the cable, with river washed coarse sand, as per standard practice with proper compactioncomplete all as specified (Punned thickness 18 cm shall be considered for payment as per para 19.75 of SSR Part-I).

M&L for providing 100mm thick PCC (1:3:6) type C2 using 40mm graded aggregate as in sub base of floor complete all as specified

M&L for providing 40mm thick PCC (1:2:4) type B1 using 20mm graded aggregate as in sub base of floor complete all as specified

M&L for coloured joint free non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors, skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with tile including 15mm thick screed bed in cement mortor 1:6 complete all as specified

M&L for glazed ceramic coloured joint free tiles 300x450x7 mm thick as on vertical surface of wall such as skirting, dado, riser etc. in Bath, WC, Kitchen and inside cupboards set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including 10 mm thick rendering in cement mortar 1:4 complete all as specified

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified

S&F Factory Made Solid PVC Moulded Door Shutter with wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm prelam PVC Sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified

S&F Stainless steel butt hinges medium weight 100mm long for PVC door complete all as specified

S&F Aluminium anodized barrel tower bolts, extruded section 200mm long complete all as specified

S&F Aluminium anodized handles, D type, 150mm long complete all as specified

S&F Steel ventilators with centre hung shutter including two pairs of brass cup pivots, catch spring and pulley wheel, complete all as specifed.

Supply & fixing of Galvanised steel wire cloth. 0.63 mm nominal dia of wire and average width of aperture 1.40mm complete all specified.

M&L for 75MM thickPCC 1:3:6 type C-1 using 20 mm graded stone agg as in plinth protection complete all as specified

S&F of 4 mm thick Sheet glass frosted , ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified

M&L for two coat of synthetic enamel paint over a coat of yellow primer including preparation on steel surfaces of any description over 10 cm width or girth complete all as specified

S/F vitreous wash down water closet pan pedestal pattern white ncluding connection in drain and in flushing pipe complete including p or s trap and including plastic water closet cseat cover with flat bottom and cover with ms chromium plated hinge device isi marked complete all as specified and directed Make: Prayag model GLECY No 4022 for pan and 518 for seat cover or equivalent as in the list of makes complete all as specified

S/F in 10 litres cap PVC low level valve less symphonic action type flushing cistern white with inlet, ball valve, float and handle including brackets and flushing pipe, complete all as specified .Make: Prayag model Gracia No 701 or equivalent as in the list of makes complete all as specified

S&F Vitreous China wash basin white, flat back size 560X415X820 mm including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipeincluding brackets, complete all as specified Make: Prayag model ROLLIN NO. 4602 or equivalent as in the list of makes complete all as specified

S& F Vitreous China bowl urinal flat back, sizeof 330 x 250 x 445 mm white (minimum),with grating and union for discharge pipe(excluding flushing cistern, flush pipe and waste pipe), complete including providing and fixing plugs, bedding urinals gainst wall in cement mortar1:2, securing urinal to plugs withand including 60mmlong brassscrews, pointing around urinal back in cement; fixing automatic flushing cistern with brackets,flush pipe, grating and Union fordischarge pipe complete all as specified and directed.Make: Prayag model 4999 or equivalent as in the list of makes complete all as specified

S&F for 20mm bore tube medium grade galvanized with all fitting and fixed to wall, ceiling or laid in floor and trench complete all as specified

S&F for 15mm bore tube medium grade galvanized with all fitting and fixed to wall, ceiling or laid in floor and trench complete all as specified

S&F 15mm bore Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified Make: Prayag model Matrix 6502 or equivalent as in the list of makes complete all as specified

S&F 15 mm dial PVC connection 450 mm long, complete all as specified

S&F waste coupling of PTMT (half of full threaded) complete all as specified

S&F Grating doom 100mm dia of PTMT (Minimum weight 25gms) complete all as specified.

S&F 15mm bore Bib taps, cast copper alloy fancy type chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified

S&F 15 mm bore Stop valves, cast copper alloy, fancy type chromium plated screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified

S&F Towel Rail 450mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 170gms) complete all as specified

M&L for PVC Floor trap 75 mm outlet, plain with grating including joning with solvent cement complete all as specified

M&L PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified

M&L for 110 mm bore PVC (SWR) pipes ' type A'single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified

Ditto as above but in wall complete all as specified.

M&L for 75 mm bore PVC (SWR) pipes ' type A' single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified

M&L for 110 mm bore PVC (SWR) vent cowl complete all as specified

M&L PVC (SWR) bends with access door of 110mm bore any radius complete all as specified.

Material and labour for hoisting and fixing rotational moulded polyethylene(double layer cylindrical vertical) LLDPE water storage tanks 1000 lit capacity ISI marked(IS-12701:1996) hoisted and fixed in position including inlet, oulet and over flow connection etc complete all as specified.

Supply and laying 3mm thick five layered polymeric APP membrane (weight not less than 3 Kg per Sqm) reinforced with non-woven polyester matt of central core 90 micron thick (weight not less than 150gms/sqm) high density polythene film, protected on both sides with high quality polymeric asphaltic mix protected on both sides with thermo-fusible HM HDPE film laid on primed surface using oil based bituminous primer @0.40Kg/sqm by torch application all as per manufacturer’s specification complete all as specified Make: “Torchshield P2160” of Pidilite/ “Super thermolay: of STP or equivalent. Note: (i) Membrane shall be laid using butane torch and sealing all joints etc all as per Para 11.44.5 of SSR Part-I.

M&L for PCC for concrete bed to drain pipe , 200 mm bore pipe including packing and under hunching against the sides of pipe after they are laid and tested in PCC (1:3:6) type C-2 using 40 mm graded stone aggreagate complete all as specified

M&L for 200 mm bore grade 'A' SGSW drain pipe laidin trenches and jointed in cement ,mortar (1:1) complete all as specified.

M&L 60 mm thick M-30 grade factory made vibratory compacted cement concrete rubber moulded, interlocking paver block any shape and size confiroming to IS 15658-2006 with grey cement and pigment as approved laid over and incl 50 mm thick consolidated sand cushion and joints filled with sand complete all as specified

M & L for PCC 1:2:4 type B-I ,(using 20 mm graded stone aggregate) as. in footpath coping /benching to sides of foot path fininished fair and even etc complete all as specified

S&F steel work in Trusses, purlins, posts and the like using tubular/ square hollow section including special shaped washer etc. complete using ERW or induction butt welded tubes/SHS conforming I.S.1161-2014/IS 4923-1977 grade St-240 complete all as specified

Supply and fix 0.50mm thick prepainted galvalume polyester coated (SMP coating) coloured metal roofing sheet trapezoidal profile having tensile strength 550Mpa as in roof covering fixed with self drilling screws with EPDM washer etc complete all as specified.

Ditto---- all as per item No 71.00 above but as in eaves board fixed with selp tapping screw as specified.

M&L for cement concrete type B-2, 1:2;4 (40 mm graded aggregate) 100mm thick complete all as specified

M&L for two coat of acrylic distember on new wall surface over a coat of primer including preperation of the surface all as directed and specified.

M&L Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in CM 1:4 complete all as specified

M&L for 75 mm Cement concrete type B- 2, 1:2:4 (40mm graded aggregate) complete all as specified

M&L for Flush pointing to brick walls in CM 1:4 complete all as specified

M&L Keyed pointing to brick walls in CM 1:4 complete all as specified

M&L for RCC Type B1, nominal mix 1:1.5:3 (20 mm graded aggregate) in chimney and shafts complete all as specified

M&L for, Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) Fe 410 -W (Gde-E- 250) quality- A complete all as specified

M&L for Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete Fe 410 -W (Gde-E- 250) quality- A complete all as specified

M&L 100 mm PCC (1:4:8) type D-2 using 40 mm graded stone agg as in sub base complete all as specified.

M&L 100 mm PCC (1:2:4) type D-2 using 40 mm graded stone agg as in sub base complete all as specified.

M&L for forming 12mm thick expansion joints filled with pre formed bituminous filler and top 30mm primed and sealed with sealing compond grade 'A'complete all as specified.

M&L Point wiring for one light point/fan point controlled by one switch with 1.5 sqmm PVC FRLSH insulated un-sheathed copper conductor single core multi strand flexible cable and 1.5 sqmm PVC FRLSH insulated un-sheathed copper conductor single core multi stranded flexible cable (green color) as earth lead in and including cable 1100 volts grade including concealed conduit (ISI marked) for one light/ fan point including rectangular sunken box open recessed cover with 3mm thick plastic laminated sheet cover including cutting chases to wall making good the disturbed surfaces to match with the existing specification complete all as specified

ALL as per item no. 85 but One ceiling fan / exhaust fan point controlled by one way switch 5/6 amps complete all as specified.

ALL as per item no. 85 but One socket out let 5/6 amps point on the same board complete all as specified.

ALL as per item no. 85 but One socket out let 5/6 amps point on the independent board complete all as specified.

All as per item no 85 here in above but copper conductor of size 2.5 sqmm for 15/16 Amp socket on independent board complete all as specified.

S&F Switch piano type flush 6 Amp Single pole one way ( ISI Marked) complete all as specified

S&F socket outlet 2 in 1, 3 pin 5 Amps complete all as specified

S & F Socket outlet 2 in 1,3 pin 15 Amp, flush type complete all as specified

S & F switch piano type one way, flush type 15 Amp complete all as specified

S & F Wall monted slim LED batten 20W, with extruded aluminium housing, with integrated LED driver fixed over 02 nos. of PVC square block surge suppressor of min 4 KV and lumen output min 120 limen per watt complete all as specified

M&L for street light bracket, made out of GI pipe medium grade) 32mm bore, 1.2 m long bend to shape and fixing/grouting with wall using 2 Nos 25 x 5 mm size MS FI clamps with bolts, nuts & washers complete including drilling as necessary and two coats of Aluminium paint over a coat of Red oxide primer all as specified

Supply and Fixing sheet metal enclosure, 8 way Distribution Boards Single door,240 volts grade single pole and neutral with 200 amps rated bus bar,IP 20 protection fixed to wall using nuts & bolts and washer of suitable dia and grouted to wall using suitable gutties complete all as specified

Supply and Fixing MCB DB double door, powder coated sheet metal enclosure, 4 way 240 volts grade single pole and neutral with 200 amps rated bus bar,IP 20 protection fixed to wall using nuts & bolts and washer of suitable dia and grouted to wall using suitable gutties complete all as specified

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size surge suppressor not less than 4 KV efficacy not less than 100 lumen per watt complete all as specified

Supply and fixing LED street Light fitting 35 watt 230 V AC outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver , lamp bracket with impact and corrosion ressistant including thermal management in multiple optics complete with IP 65/66 Protection having SPD not less than 5 KV lumen output > 120 lumen per watt complete all as specified . Note: includes GI Bracket, clamp and other fixing acessories .

-----Blank-----

S&F exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers complete with making hole in wall and fixing accordingly all as specified.

S&F ceiling rose surface backelite 65x50mm two to three terminal (ISI marked) complete all as specified .

S&F MCB 'C' series, SPN 240V, 32 Amp all as specified

S&F MCB 'C' series, single pole 240V , 6 to 32 Amp all as specified

S & F MCB DB confirming to IP 43 - IK 09 with acrylic door, 4 way double door complete with all connections -Phase, Neutral and Earthing bar and making good the disturbed surfaces.Complete all as specified

Earthing complete with galvanized steel earth plate electrode electrode 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less then 2.25m deep below normal ground level ) with top edge of plate not less than 1.5m below normal ground level connecting to the galvanized iron earth lead 4mm dia , by means of bolts , nuts, check nuts and washer of galvanized iron and 4mm dia GI earth wire protected by provision of GI medium grade pipe 15mm upto 7.5 mtr bore including provision of concrete pit in PCC (1:2:4) type B-1 using 20 mm graded stone aggregates with 40mm thick cover of RCC (1:1.5:3) Type A1 reinforced with XPM (weight not less than 4 kg/sqm) and frame of angle iron 25 x 25 x 3mm with lugs 02 Nos and ith 6mm dia MS bar handle made to shape , GI light grade 20mm bore pipe for watering perforated at bottom 1.75 mtr long placed on top edge of earth plate , common salt and charcoal filling , test point made out of bronze/Gun metal with fixing arrangements , funnel , wire mesh and excavation /earth work in hard dense soil , returning filling in and removal of surplus soil to a distance not exceeding 50 mtr , all as per electrical plate no 3 of SSR -2010 Part-I and connecting to earth test point all as specified or indicated including testing on complete all as specified

M & L for bricks; common burnt clay building bricks, sub-class ‘B’ Designation 75 complete all as specified

Supply laying & testing cable XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) with aluminium conductor, 11000 volts, (Earthed), grade cross sectional area 10 sq. mm, 2 core complete all as specified

M & L for laying of GI pipe light grade across road for cable protection complete of size 40mm complete all as specified

M & L for horizontal boring across the exsisting road without disturbing the road surface for inserting GI pipe complete all as specified and directed . Note:- (i) Removal of surplus soil shall be deemed to be include in the unit Rate . (ii) GI pipe will be measured and paid separately under relevant item complete all as specified

Supply and laying in Trenches GI water Tubing medium grade of 25 mm dia including all fittings such as sockets, bends, elbows, Union etc . Complete all as specified

Supply and laying for brick protection for protection of cable over sand cushioning cables inside the trench by using common brunt clay building bricks sub-class “B” old size brick and flat and width wise along the axis of the trench complete all as specified

Supply and fix Gun metal ,globe Gate Valves with iron wheel head of 25 mm dia bore complete with all accessories all as specified.

M& L for cutting existing GI pipe alteration or addition of 40/50 mm dia bore for inerstion of reducer Tee complete with all accessories all as specified

SHRI PRADEEP PARIK (BID ID -3339235)

BBKundu (BID ID -3340826)

R K AGARWAL (BID ID -3341201)

flexpro construction company (BID ID -3340577)

M/s. RAMPHAL GARG (BID ID -3341718)