PROVN OF TILING IN TOILET BATHROOM OF BLDG P-2 P-3 P-4 P-5 P-6 P-7 OF 2/8 GR DRAINAGE COVER FROM KSP TO KGBS OF 3/11 GR AND SPL REP TO BLDG T-52 AT 3/11 GR ATGHUNGHORA CANTT UNDER GE DEHRADUN

Amount

M&L for brick work with sub class 'B' brick straight or curved on plan exc. 6 m mean radius built in cement mortar 1:6 including demolition of existing old brick work or stone masonry built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed.

All as per Item No. 01 above but except brick complete. Note : Old serviceable brick obtained from demolition shall be reused. The rate quoted against this item is inclusive of necessary cleaning and stacking of bricks before incorporation in the work.

M&L for brick work with sub class 'B' brick straight or curved on plan to any radius built in cement mortar 1:4 as in half brick thick wall including demolition of existing brick work or stone masonry built in cement mortar including all quoins, arches, pillars etc. complete all as specified.

M&L for 15 mm thick rendering on brick work or concrete surface in cement mortar 1:6, surface finished even and fair complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar 1:6 on brick work or concrete surface, surface finished even and fair including taking down existing cement plaster including racking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed.

M&L for 15 mm thick rendering on brick work or concrete surface in cement mortar 1:4 mixed with water proofing compound, surface finished even and smooth including taking down existing cement plaster including racking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed. Note: Water proofing compound shall be measured and paid separately as supply only.

M&L for 15 mm thick rendering on brick work or concrete surface in cement mortar 1:4 mixed with water proofing compound, surface finished even and smooth complete all as specified and directed. Note : Water proofing compound shall be measured and paid separately as supply only.

Supply only integral water proofing compound complete all as specified.

M&L for applying 1 to 1.5 mm thick wall care putty for preparation of old/new surfaces of wall as per manufacturer’s instruction complete all as specified and directed.

M&L for applying two coats of oil bound distemper over a coat of primer on wall surfaces complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying two coat of cement base paint over one coat of primer complete all as specified and directed.

M&L for preparing of old decorated surfaces of wall, pilasters, cornices, AC sheet etc. by washing, rubbing down & stopping etc and applying one coat of cement based paint complete all as specified and directed.

M&L for PCC 1:2:4 type B-0 using 12.50 mm graded stone aggregate as in leveling course to floors complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in benching to drain, holdfast, padding to roof/chhajja, coping, bed block etc. and the like edge slightly rounded or chamfered including necessary use and waste of form work complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6 type C-1 using 20 mm graded stone aggregate as in plinth protection or similar places, laid in alternate bays and filling the joints with & including bitumen and sand 1:3 by weight, surface finished even and fair without using extra cement complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in foundation filling, mass concrete, sub base or leveling course of floor etc. complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in surface channel and drain including necessary use and waste of form work and not exc 15 cm thick in ground floor and paving below or above ground level complete all as specified.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds mitered or stopped ends etc. complete all as specified and directed.

M&L for 20-25mm thick machine cut Kota stone slab in flooring laid over and including 20mm thick cement screed base in CM 1:4, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for 18-20mm thick machine cut Kota stone in skirting laid over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab over and including 10 mm back coat in CM 1 :3, complete all as specified and directed.

Taking down chowkhats or frames n. exc 1.5 sqm each without taking off shutter from the frame complete all as specified and directed.

Taking down chowkhats or frames exc. 1.5 Sqm but not exceeding 4 Sqm each complete all as specified and directed.

S&F mild steel work as in holdfast, hooks for hanging fans and similar small articles conforming to Fe- 290 Gde-E-165 including necessary welding or fixing nuts and bolts complete all as specified and directed.

S&F mild steel framed work such as door frame, grills, grating etc. with ends of bar shoulder and/or riveted, or forged into spikes, framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 including necessary welding, drilling hole complete all as specified and directed.

S&F 35mm thick 2nd class hard wood factory made plain, framed paneled shutter (any number of panels) with panels of 12 mm made BWP grade BWR plywood. The rail and stile as per IS-1003 (Pat-I) kiln seasoned and chemically pressure treated complete all as specified.

S&F 35mm thick second class hardwood glazed and Skelton factory made door shutters, open rebated and prepared to receive glass/gauze etc divided into squares with plain, chamfered or rounded mitered and rebated sash bars, edges of framing plain, chamfered, fitting with cut and rebated beads for securing glass/ gauge complete all as specified in SSR Pt I-2009 section 8 clause 8.24 (a) and as directed.

S&F factory made steel window with side hung shutters including projecting/box/pin type hinges with steel handle, steel peg stay,tower bolt etc. complete with glazing bars, dovetailed or welded complete all as specified and directed.

S&F factory made steel window with side hung shutters including projecting/box/pin type hinges with steel handle, steel peg stay, tower bolt etc. complete without glazing bars, dovetailed or welded complete all as specified and directed.

S&F 200 mm long aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 100 mm size butt hinges, medium weight, cold rolled mild steel complete all as specified and directed.

S&F 125 mm size aluminium handles cast type, anodised complete all as specified and directed.

S&F 300 mm mild steel sliding door bolt plate type, stove enameled black, with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed.

M&L for floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring, fixed to floor of size 150 mm complete all as specified and directed.

S&F 2nd class hardwood small fittings such as brackets of any type, latch and hinge block, shaped door and window stops and the like including all labours articles n. exc. 200 cucm each with 75 mm long hinge complete all as specified and directed.

S&F 300 mm mild steel, ordinary rat tail rod pattern spring including roller and roller plate complete all as specified and directed.

M&L for applying two coats of synthetic enamel paint on new wooden surfaces of any description over 10 cm width or girth over a coat of pink primer including preparation of surfaces complete all as specified and directed.

S&F galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm complete all as specified and directed.

S&F 3 mm thick plain sheet glass ordinary quality and glazing with oil putty or wooden beads in square area n. exc. 0.5 Sqm in each pane complete all as specified and directed.

Dismantling of AC sheet (corrugated or semi corrugated etc) including AC ridges as in roof covering complete all as specified and directed. Note:- Opening of existing wind tie where required for taking down of AC sheet is included in the rate quoted against this item.

S&F pre- painted galvalume aluminum zink coating GI based corrugated steel sheet 0.5 mm thick of an colour having tensile strength of 550 Mpa as in roof covering / cladding to wall , fixed with self tapping screw complete all as specified and directed. Note:- The profile of sheet shall be as per sample kept in GE's office.

S&F pre- painted galvalume aluminum zink coating GI based plain steel sheet 0.5 mm thick of an colour having tensile strength of 550 Mpa as in roof covering / cladding to wall , fixed with self tapping screw complete all as specified and directed. Note:- The profile of sheet shall be as per sample kept in GE's office.

Dismantling of timber scantling 40 Sqcm and over in section in any position complete all as specified.

Dismantling timber scantling as in fillets, rails, posts, rafters, purlins etc under 40 Sqcm in section complete all as specified and directed.

S&F mild steel work as in main and cross beam, hip and jack rafters, purlins etc. fixed with angle cleat or other connecting plate complete confirming to Fe – 410-O or Fe – 310-O complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulps, insulation etc.) or insulation boards/slabs/blanket, any thickness, including cover fillets complete all as specified and as directed.

S&F 600x600mmx4mm thick 'E' board class ic as in false ceiling including supply and fixing 'Tee" grid frame work made of special section of MS galvanized sheet 0.30mm thick, bottom portion painted with cellular nitro painting, consisting angle cleats of size 25mm wide 1.6mm thick with flag fixed to RCC ceiling with dash fastener or wraping the suspending wire around the existing wooden/steel purlin/rafter for suslpending grid frame work of size 600mmx600mm suspended with 02 Nos, 1.60mm dia GI wire @ 600mm C/C on main Tee and fixed to T-grid with the help of level clip or as per manufacturer direction. The section consisting of main Tee 37mm x24mmx0.60mm thick, cross runner tee 37mmx24mmx0.60mm and. Perimeter angle 24mmx24mmx0.50mm thick shall be fixed to wall with GI screw of 40mm long @ 450mm C/C along the perimeter of wall including or wall including applying two coats of distemper oil emulsion all as per manufacturer's instruction complete all as specified and directed.;

Dismantling structural/framed steel work of any description as in purlin, rafter, grills, grating &doors etc. complete all as specified and directed.

M&L for applying two coats of synthetic enamel paint on new or previously untreated steel surfaces of any description over 10 cm width or girth over a coat of red oxide primer including preparation of steel surfaces complete all as specified and directed.

M&L for applying one coat of synthetic enamel paint on old steel surfaces of any description over 10 cm width or girth over a coat of red oxide primer including preparation of steel surfaces complete all as specified and directed.

S&F MS drapery rod with wooden finish, decorative incl brackets, decorative finals at both ends & curtain rings 8 Nos (Minimum) complete all as specified.

S&F 600 x450 mm beveled edge mirror mounted on 6mm thick AC building board to fixed to wooden plug with CP brackets screw fixed, fixed in repair complete all as specified and directed.

Providing and injecting chemical emulsion for Post Constructional Anti-Termite Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement 2 coarse sand) to match the existing floors complete all as specified and directed.

Providing and injecting chemical emulsion for Post Constructional Anti-Termite Treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear meter including drilling and plugging holes etc in apron complete all as specified and directed.

M&L for RCC1:2:4 type B1 using 20 mm graded stone aggregate as in beam, cantilevers, lintel chajjas etc. Including demolition of existing old RCC complete all as specified and as directed.

Use and waste form work to sides and soffits of floor or roof beams, lintel, and cantilevers, shelves etc. including support of fair finished surfaces complete all as specified and as directed.

S&F mild steel TMT bar 8 to 10 mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed.

S&F mild steel TMT bar 6 to 8 mm dia as in stirrups cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed.

Demolition of cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L for 25 mm thick PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in leveling course to floors complete all as specified and directed.

M&L for Non skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

M&L for Glazed ceramic tiles in vertical surface 300x 200x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10 mm thick rendering in cement mortar 1:4 and including dismantling of existing wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified complete all as specified and directed.

Providing precast cement concrete type B1 (20mm graded aggregate) in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain face set in cement mortar 1:4 including necessary form work complete all as specified and directed.

Taking down carefully copper/Aluminum point wiring (light, fan socket and power) complete including switches, ceiling rose lamp holder and regulator etc and removing from site and making good disturbed surfaces of walls/floors etc complete all as specified and directed.

M&L for point wiring with 1.5 Sqmm. (nominal area) FRLS, single core PVC insulated 1100 Volts, grade multi stranded copper conductor unsheathed in and including concealed PVC conduit medium duty 20 mm dia or higher and heavy grade conduit fittings and heavy duty accessories with suitable size of sunk type cast iron or pressed steel terminal box 1.6mm thick for mounting of switches, sockets, fan regulator etc with 3 mm thick plastic laminated sheet as top cover, one green colour FRLS cable of same size as earth wire up to common earth and connected to earth dolly complete all as specified and directed. Note: The wiring to be done as per IE rule and maintain colour code accordingly.

One light point/ ceiling fan point/ Exhaust fan point controlled by one-one way switch.

One three pin 5 Amp socket on same board with other switches.

One three pin 5 Amp socket on independent board

All as per item No. 2.00 above but one 3 pin socket outlet 15 Amp independent, cable 2.5 Sqmm PVC insulated unsheathed multi stranded copper cable FRLS for phase & neutral, with 2.5Sqmm PVC insulated unsheathed multi stranded copper conductor cable FRLS as earth continuity conductor.

S&F switch piano flush, button type 5 Amp SP 250 V AC complete all as specified & directed.

S&F switch piano flush button type 15 Amps SP 250 V AC complete all as specified & directed.

S&F socket outlet multipurpose 3 Pin 5 Amp and 2 Pin 5 Amps 250 V AC complete all as specified & directed.

S&F socket outlet two in one three pin 5 Amp and 15 Amp 2 module 120 W flush type complete al as specified.

S&F step type regulator socket type double module 5 step for ceiling fan 1200/1400 mm size 230 volts 6 Ampds 400 watts complete all as specified & directed.

S&F ceiling rose, 3 terminal/PVC/polycarbonate, isolated body 250 V AC complete all as specified & directed.

M&L lamp holder insulated body with back plate suitable for angle and batten fitting complete all as specified & directed.

M&L sub main wiring with 2 Single core PVC insulated unsheathed FRLS cable 1100 Volts grade heavy duty copper conductor multi stranded of size 10 Sq.mm. (nominal area) drawing in and including 20 mm. dia or higher PVC concealed conduit heavy duty accessories and fittings. PVC insulated unsheathed FRLS cable copper conductor multi stranded of size 6 Sq. mm. as earth wire up to common earth and connected to earth dolly complete all as specified and directed.

S&F sheet metal enclosures 240 volt with 200 Amp rated bus bar for double door 8 way DB,s IP-43 IK 09 metal door suitable for one MCB SPN as incoming and 06 MCB SP as outgoing complete all as specified and directed.

S&F sheet metal enclosures triple pole and neutral double door 415 Volt 4 way DBs IP-43 IK- 09 Vertical type suitable for 200 Ams rated bus bar & one MCCB 100 Amp as incoming and 12 MCB SP as outgoing complete all as specified and directed.

S&F MCB double pole 240 Volt 10 KA 40 Amp 'B' series conforming to ISI marked complete all as specified and directed.

S&F MCB single pole and 240 volt 10 KA 5-32 Amp 'B' series conforming to ISI marked complete all as specified and directed.

S&F MCCB 415 Volt 16 KA 4 pole 63 Amp magnetic trip release & setting as incoming with fixing arrangement complete all as specified and directed.

S&F in replacement wall mounted tube light fitting 1x20/22 watts extruded aluminium polycarbonate covers PF 0.9 and above operating voltage 140V-270V colour temp 6500K & lumen input output 95 Lumen per watt and connected to ceiling rose with required length of two core flexible copper cable 23/0.0076 fixed on wall/roof complete all as specified and directed. Make: Philips cat part No TMC 501P1xT LED 22WP-3241(Tube Batten) and MAS LE$D 1200mm 18W-865-T-81 (Tube) / Wipro Cat part No WI0922208 (Tube Batten) LL13-181-65SE (Tube)/ Havells Cat Part No LUMILINEPLUSBS20WLED865SPCSS (Tube Batten)CRYSTAL1213T8DSTL20WLED865SGLASS(TUBE DOUBLE SIDE)

S&F in replacement LED light fitting decorative wall mounting SS brush finish fixture with frosted glass suitable for up to 1x40 watt mini glass lamp with and including one no 12 watt LED lamp. complete with accessories and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed.

S&F mirror light decorative compact luminaries with decorative ends caps 9/10 Watt LED with all accessories and including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S & F high efficiency LED bulbs 1 X 12 watt that can be used as a ready replacement for existing GLS ad CFL direct fit in holder complete all as specified and directed.

Supply and Fixing Integral LED Street Light Luminaire comprising of pressure die cast aluminum housing heat resistant toughened glass with frame IP-65 protection road way luminaries with high power LED 60 watt with efficiency 100 lumen/watt at system level, CCT>5700K, with average life class 50,000 burning hours, including taking out old unserviceable street light complete all as specified and directed. Make:- Crompton model No. LSTP-45-CDL/Havells model No. ENDURAPEARLNEOSL 40WLED757PASYTOPC /Philips Cat Part No BRP409LED CW036MRFGIPSUGRand SYSKA, SSK-ST-40W.

S&F ceiling fans complete with blades, down rods, copper wound, double bearing without electronic regulator and accessories, AC, 230V, 1200mm sweep, min air delivery 210 CFM with service value 6.00 complete all as specified and directed

M&L for air ventilation fan metallic body 300mm, 900 RPM, single phase, 230V AC including necessary, making hole fixing arrangement on wall with frame hold fastener, bolt, washer etc including connection with twisted white three core flexible copper multi stranded conductor cable from ceiling rose to connector complete all as specified and directed. Note: old unserviceable fan shall be deposit in E/M yard.

M&L for excavation in trenches n. exc. 1.5 mtr wide and n. exc. 1.5 mtr in depth for laying of underground cable, foundation of pole and getting out in soft/loose soil complete all as specified and directed.

M&L for returning, filling in excavated soil in trenches including spreading, leveling, watering and well ramming in layers n. exc. 25 cm thick complete all as specified and directed.

M&L for removing of excavated soil to a distance n. exc. 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed.

Supply & laying Sand coarse dry as in cushioning of underground electric cable in trenches, laid to a uniform thickness of 23cm (15cm under the cable & 8cm over the cable ) and gently punned down to 18cm thickness all complete all as specified and directed. Note :- Only punned down sand thickness 18CM shall be measured and paid.

Supplying and laying old size bricks, laid flat ie length of brick shall be laid across the cable, common burnt clay building bricks sub class `B' designation 75 complete all as specified and directed and testing on completion complete all as specified and directed.

Supply, laying, jointing and testing of underground XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 25 Sqmm 4 Core laid in trenches/ducts/along poles/through pipe under road etc with new aluminium lugs of cable size all as specified and directed.

Supply and laying galvanised steel tubing 50 mm bore light grade laid in trenches or fixed to poles/walls etc for cable protection complete all as specified and directed.

Materials and Labour for earthing complete with galvanized steel earth plate electrode 600 mm x 600 mm x 6.0 mm thick buried directly in ground end vertically to a depth not less than 2.25 meter deep below ground level with top edge of the earth plate at a depth not less than 1.5 M below normal ground level connected to galvanized steel earth wire 4 mm dia by means of bolts, nuts check nuts and washers of galvanized steel and connected to main switch board or main control board as directed and including provision of concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1, cover slab 54 cm x 54 cm x 5 cm reinforced with 8 mm dia. TMT bars @ 150 mm c/c both ways, and with one handle for lifting made out of 10 mm dia MS round bar, provision of funnel, wire mesh, 20 mm bore galvanized steel tubing (Medium grade) for watering, charcoal or coke and salt in alternate layers, 15 mm bore galvanized steel tubing (light grade) for protection of earth lead connection, including necessary excavation and earth work in any type of soil and necessary testing complete all as shown on electrical plate No 3 of SSR Part –I (2009) and as directed.

M/s Pradeep Kumar

MOHAN LAL GUPTA

PAWAN KUMAR

M/s RP AGRAWAL

M/S C S AITHANI

Gupta Brothers

AYUSH CONSTRUCTION COMPANY