SPECIAL REPAIR TO OTM BLDG NOS P 91 NP 04 AND P 79 AT MIL STN DHRANGADHRA

Amount

M&L for plain cement concrete (1:2:4) type B-2, using 40 mm graded stone aggregate as in foundation, filling, Bed blocks and mass concrete complete all as specified and directed. Note:- Volume of column embedded in PCC shall be deducted for payment purpose.

M&L for plain cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate for bed block/padestal/coping around poles, including necessary form work, finishing even and smooth without using extra cement, all as specified and directed.

M&L for RCC 1:2:4 , type B-1 using 20mm graded stone aggregate suspended slabs supported on walls/columns, in floors, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Supply only, integral water proofing compound.

M&L for Brick work with old size, sub class 'B' bricks, straight or curved on plan exc. 6m mean radius built in cement mortar (1:6) complete all as specified and directed.

M&L for Brick work with old size, sub class 'B' bricks, straight or curved on plan any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed.

Cutting chases, pinning in, making good to facings in stone concrete block or slab walls where required and pointing in cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting exceeding 20 cm girth complete all as specified & directed.

M&L for walling of random rubble stone masonry, uncoarsed, well bonded, bedded and solidly hearted, built in cement mortar 1:6 complete all as specified and directed.

M&L for walling of random rubble stone masonry, brought up to courses, well bonded, bedded and solidly hearted, built in cement mortar 1:6 complete all as specified and directed.

Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints, as specified, of random rubble walling, uncoursed or brought upto course with maximum depression on face from straight edge held against the dressed surface not.exc. 20mm for sand stone complete all as specified and directed.

M&L for form work to chullah hoods, chajjas , troughs and simollar items including edges and rough finished surfaces of concrete all as specified and directed.

M&L for form work to sides and soffit of floor or roof beams, beams haunchingss, girders, brussummers, lintels, cantilevers, shelves including sup-ports, overhangs, etc and rough finished surfaces of concrete all as specified and directed.

M&L for plain fillets of 2nd class hardwood, square, rectangular or triangular in section exc 3cm but n.exc. 6cm, clean sawn, secured with nails or brads complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutter from the frames) exc. 1.5sq.m but not exc. 4sq.m each complete all as specified and directed.

S&F, solid PVC Double door frame of size 50mm x 95mm made out of 5mm Plain colour PVC sheet reinforced with M.S. tube, suppling & fixing in opening as per specification & drawing, fixed with wall usint 65/100mm MS screws through the frame by using fasteners with 4 nos screws in each vertical member & 02 Nos of screws in horizontal members etc. complete all as specified and directed.

S&F, factory made solid PVC moulded door shutter, with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed.

S&F, aluminium anodised, barrel tower bolts of extruded section with length of bolt 150 mm and fixed complete all as specified and directed

S&F, butt hinges 100mm long, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed complete all as specified and directed.

S&F, in repair, 150 mm size extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F, in repair, Mortice lock, brass, four lever, verticle type, size 75mm complete all as specified and directed.

S&F, continuous (piano) hinges, mild steel bright finish or electrogalvanised, width of flap 40 mm complete all as specified and directed.

S&F, hasp & staples 125mm in size, safety type alu. anodised fixed with screws complete all as specified.

S&F, in repair, aluminium (Die cast) body, Door closer, hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80kg and fixed.

S&F, galvanised mild steel wire cloth 0.63 mm nominal dia of wire and average width of aperture 1.40mm and fixed wth tinned tacks or galvanized wire staples or wooden bead complete all as specified and directed.

S&F, stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

M&L for mild steel framed work such as grills, gratings, etc. with ends of bars, shouldered and/or riveted, or forged into spikes, framed guard bars etc and similar work conforming to Fe-290 (Gde-E-165) including applying one shop coat of red oxide primer complete all as specified and directed

S&F, MS angle iron Fe-410-W (Gde-E-250) quality A in framed work for roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle channel or flat sections) including distance pieces, cleats etc incl one shop coat of zinc chrome primer complete all as specified and directed.

S&F, Aluminium anodised doors/windows/ventilators with one or more rebates including joining cleat for fixing etc complete with frame and shutter of size directed by Engineer-in-charge including handles, tower bolts, grills, etc complete all as specified and directed. Note:- Floor door spring, sheet glass, wire cloth, lock, rubber gasket, etc shall be measured and paid seperately.

S&F, pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet, 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F, pre-painted galvalume aluminium zinc coating GI based plain steel sheet, 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F, in repair, false ceiling, at any height, 600 x 600mm grid with Armstrong 'Prelude XL 32' grid system and 16mm thick mineral fibre acoustic tile 'RH - 99 Classic lite' with suspension system complete all as specified and per manufacturer's instruction. Make : Armstrong or equivalent as approved by GE.

M&L for asbestos cement plain building boards, fixed to timber framework with screws complete all as specified and directed.

M&L for 25mm thick particle board, medium density, flat pressed, single layer type or three layer type with BWR type adhesive, fixed with screws to timber frame work complete all as specified and directed.

S&F, in repair, 18/19mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice laminations and other side balanceing white lamination, fixed with screws to timber frame work in cup boards, rebated or flat edged complete all as specified and directed.

M&L for 6mm thick external teak wood lipping fixed to18/19mm thick prelaminated particle boards with screws.

M&L for 18-20mm thick black granite stone slab machine cut in skirting/dado, cooking platform, jams, pillars, windows cills and the like laid over and including 10mm thick screed bed or backing coat in cement mortar (1:4) and jointed with grey cement slurry and pointed with white cement and with admixture or pigment to match the shade of granite stone including grinding and polishing complete all as specified and directed.

Rounding to edges of stone slabs one edge, such as steps, cooking plateform, and other similar situations complete all as specified and directed.

M&L for 50mm thick cement concrete 1:3:6 type C1, using 20mm graded stone aggregate as in plinth protection, finishing cement concrete surfaces even and smooth without using extra cement, Joints of plinth protection shall be filled with bitumen mastic (1:3) complete all as specified and as directed.

M&L for 75 mm thick cement concrete (1:3:6) type C-2 using 40 mm graded stone aggregate as in sub base of flooring/hard standing, path and finishing the surface even and fair without using extra cement complete all as specified and directed.

M&L for 25mm thick cement concrete 1:2:4 type B-0 using 12.5mm graded stone aggregate in sub base to receive floor finishes complete all as specified and directed.

M&L for roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. complete all as specified and directed.

M&L for Coloured glazed ceramic tiles of size 300 x 200 x 7mm thick, on vertical wall surface, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces over and including 10mm thick backing coat in CM 1:4 complete all as specified and directed.

M&L, Non-skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete as specified and directed.

M&L, Non-skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular), area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set & jointed in net cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete as specified and directed.

M&L, Non-skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular), area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm, as in skirting/dado etc. set & jointed in net cement slurry and pointed in white or coloured cement to match over and including 10mm thick screed bed in CM 1:4 complete as specified and directed.

M&L for heavy duty, exterior grade ceramic tiles (Durastone of Somany/Endura of jhonson or equivalent as approved by GE) of size 300 x300x 10mm thick, set, jointed and pointed in neat cement slurry in trades/risers, landing with white cement and pigment over and including screed bed or bedding layer of 15 mm thick cement mortar (1:6) complete all as specified and directed.

M&L for vitrified tiles, 10mm thick (minimum), (square/ rectangular) polished, area of each tiles exceeding 0.36 Sqm (including 600mmx600mm size) but not exceeding 0.42 Sqm, in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles and over and including 15mm thick screed bed in CM (1:6) complete all as specified and directed.

M&L for vitrified tiles, 10mm thick (minimum), (square/ rectangular) polished, area of each tiles exceeding 0.36 Sqm (including 600mmx600mm size) but not exceeding 0.42 Sqm, in skirting/dado, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles and over and including 10mm thick rendering in CM (1:4) complete all as specified and directed.

M&L, for machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size conforming to IS 15658- 2006 of 60mm thickness, M-35 grade including 25mm thick sand cushion below paver blocks complete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) and removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for rendering 10mm thick in cement mortar 1:6 on stone masonry surface or surface other than fair face of brick work finished surface even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar (1:4) on walls/ floors surfaces mixed with using water proofing compound @ 3% by weight of cement or as per manufacturer instructions, finished even and smooth without using extra cement to receive WPT complete all as specified and directed. Note:- Supply only water proofing compound shall be measured and paid separately.

M&L for rendering 15mm thick in cement mortar 1:6 on stone masonry surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick cement plaster 1:4 on stone masonry surface or surface other than fair face of brickwork surface finished even and smooth without using extra cement.

M&L for rendering 20mm thick in cement mortar 1:4 on stone masonry wall surface or surface other than fair face of brickwork surface finished even and smooth without using extra cement complete all as specified and directed.

Taking down cement plaster on brick or stone wall etc. including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed.

M&L for preparing new plastered or un-plastered surfaces of walls and applying two coats of oil bound distemper over and including chalk whiting on walls complete all as specified and directed.

M&L for preparing new plastered or un-plastered surfaces of wall and applying two coats of oil bound distemper complete all as specified and directed.

M&L for preparation of old plastered surfaces of wall and applying one coat of cement base paint complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying two coat of cement base paint complete all as specified and directed.

M&L for preparing of new plastered or un-plastered wall surfaces and applying two coats of oil bound distemper over and including chalk whiting on plastered surfaces, preparatory to distempering complete all as specified and directed.

M&L for complete removal of existing treatment and preparation of old plastered or un-plastered surfaces and applying two coats of oil bound distemper over and including one coats of wall care putty complete all as specified and directed.

M&L for preparation of plastered surfaces of wall and applying two coats of weather proof exterior emulsion paint complete all as specified and directed. Make - Apex of Asian Paints or equivalent as approved by GE. (The work is to be carried at slant portion of OHR at the height of 20m).

M&L for preparation of new plastered or un-plastered surfaces of ceiling and applying two coats of oil bound distemper over a coat of primer and and including care putty complete all as specified and directed.

M&L for complete removal of existing treatment and preparation of old plastered or un-plastered surfaces of ceiling and applying two coats of oil bound distemper over one coat of primer including wall care putty complete all as specified and directed.

M&L for 4mm thick sheet glass, ordinary quality and glazing with oil putty in square not exc. 0.5sq.m in each pane complete all as specified and directed.

S&F, 4mm thick, sheet glass ordinary quality glass panes in square exc. 0.50 Sqm in each pane and fixed to aluminium doors/windows/vents with necessary rubber gaskets complete all as specified and directed.

S&F, 5mm thick, black tinted glass panes fixed to aluminium doors/windows/vents with necessary rubber gaskets complete all as specified and directed.

M&L for preparation of new steel surface of any description exc. 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

M&L for preparation of new steel surface of any description exc. 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

Taking up or down steel tubing and connections for 15mm bore of pipe complete all as specified and directed.

Taking up or down steel tubing and connections for 20mm bore of pipe complete all as specified and directed.

Taking up or down steel tubing and connections for 25mm bore of pipe complete all as specified and directed.

S&F, steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors for 15mm bore of pipe complete all as specified and directed.

S&F, steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors for 20mm bore of pipe complete all as specified and directed.

S&F steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors for 25mm bore of pipe complete all as specified and directed.

Refixing old serviceable steel tubing and connections in new or old position (walls, ceilings, floors etc.) for 15mm bore of pipe complete all as specified and directed.

Refixing old serviceable steel tubing and connections in new or old position (walls, ceilings, floors etc.) for 20mm bore of pipe complete all as specified and directed.

Refixing old serviceable steel tubing and connections in new or old position (walls, ceilings, floors etc.) for 25mm bore of pipe complete all as specified and directed.

S&F, in repair, 25mm dia, powder coated, fancy type, aluminium decorative tubular curtain rod with decorative ball type side brackets complete all as specified and directed.

S&F, brass chromium plated, tubular towel rail 20mm dia, D type, 600mm long complete all as specified and directed as per Cat No. ACN 1111NM of Make Jaquar or equivalent make as approved by GE from Appendix 'C'.

S&F, in repairs, 15mm brass chromium plated bib cock with wall fange, complete all as specified and directed as per Cat No. MQT-511 of ESSCO or equivalent make approved by GE from the make specified in Appx 'C'.

S&F, in repair, stop valve, angular, chromium plated for iron pipe or for unions and fixed to 15mm bore pipe complete all as specified and directed as per Cat No - MQT - 513A of Make : ESSCO or equivalent as approved by GE complete all as specified and directed.

S&F, in repair, concealed stop cock of 15mm, heavy body casted, chromium plated for iron pipe or for unions and fixed to 15mm bore pipe complete all as specified and directed as per Cat No - MQT - 514A of Make : ESSCO or equivalent as approved by GE complete all as specified and directed.

S&F, in repair, 8mm dia brass, chromium plated health faucet (Hand shower) with 01 meter long flexible tube and wall hook complete all as specified and directed. Make : Jaquar Cat No - ALD-573 or equivalent as approved by GE, complete all as specified and directed.

S&F, in repairs, 50mm bore, low density polyethelene pipe (HDPE) of pressure rating 6kgf/sq.cm fixed to walls, ceilings or in floors etc. complete all as specified and directed.

Supply, hoisting, fixing in position and connecting, in repairs, 500 litres capacity rotational moulded polyethylene water storage tank double layered (cylindrical, vertical with closed top), ISI marked, including fixing arrangement for inlet/outlet/over flow and vent pipe of standard size all as specified in SSR Part-I complete all as specified and directed.

Supply only, pillar taps cast copper alloy with capstan head, chromium plated, fancy type, screwed down high pressure, with or without lettered ‘hot’ or ‘cold’ with long screwed shanks and fly nuts, screwed for iron pipes 15mm bore complete all as specified and directed.

S&F, in repairs, Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed all as specified and directed for 25 mm bores of pipe.

S&F, 20mm bore, ball valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed complete all as specified and directed.(Minimum weight -210 Gms)

S&F, PVC connection 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed.

S&F, 75mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints laid in trenches or floor complete all as specified and directed.

S&F, 110mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints laid in trenches or floor/walls complete all as specified and directed.

S&F, 110mm bore PVC (SWR) bend, any radius, with access door complete all as specified and directed.

S&F, 110mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed.

S&F, 110mm bore PVC (SWR), vent cowl complete all as specified and directed.

S&F, PVC (SWR) floor trap, with chromium plated grating including jointing with solvent cement, dia of outlet 75mm complete all as specified and directed.

S&F, PVC (SWR) gully trap 125/110mm, setting and jointing with solvent cement complete all as specified and directed.

S&F, in repair, 10 litres capacity, PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet ball valve, float and handle including brackets and connection to pipe or lever etc. complete all as specified and directed.

S&F, in repairs, vitreous china wash basin, white, flat back of size 550mm x 400mm including waste fitting and brackets grouted in cement mortar 1:2 in wall complete all as specified and directed. Note :- Supply only pillar taps, waste fittings, PVC connection, PVC waste pipe shall be measured and paid separately.

S&F, Brass chromium plated bottle traps, 32mm bore, for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed

S&F, in repair, vitreous china wash down water closet pan (Pedestal pattern), white with 'p' or 's' trap (excluding flushing cistern and flush pipe), including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe etc. with seat cover complete all as specified and directed.

Dismantling cross-arms of M.S channel or angle sections etc. complete all as specified and directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc. complete all as specified and directed.

Desmantling of stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floor and pavings n exc 15cm thickness (below or above ground level) complete as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified and directed.

Dismantling asbestos cement (corrugated, semi corrugated etc.) sheets in roof covering complete all as specified and directed.

Dismantling wall and ceiling boads (fibre, pulp, insulation etc.) or insulation boards/slab/ blankets, any thickness including cover fillets complete all as specified and directed.

Dismantling of cast iron, PVC or reinforced concrete drain pipes jointed in cement mortar and taking out of trenches if required for 110mm and 75mm bore of pipe complete all as specified and directed.

Taking down carefully unserviceable copper/aluminium point wiring (Light, fan, socket or power) complete including unserviceable fittings and fixtures such as switches, ceiling roses, pendents, regulators, sockets, lamp holders, brackets, except ceiling fittings, bulk head fittings, tube light fittings etc. and making good the disturbed surfaces of walls, floors, etc. complete all as specified and directed.

M&L for wiring with and including multistranded copper conductor 1.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed FRLS cable 1100 Volts grade, ISI marked with valied CML number drawn in and including medium grade PVC casing and capping double lock type 32mm in size, fire resistant, ISI marked including with its fittings and fixtures such as tees, bends, elbows, junction boxes, etc. including multistranded copper conductor 1.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed FRLS cable 1100 Volts grade, ISI marked with valied CML number as continuity earth wire and including pressed steel sunken concealed terminal box with 3mm thick industrial laminated sheet cover for mounting switches, sockets and fan regulators etc. complete all as specified and directed for the following :-

(a) One light/fan point controlled by one switch

(b) One 3 pin, 5 Amps, socket outlet on the same board controlled by another switch.

(c) One multi pin 5 Amps, socket outlet on Independent board.

M&L for wiring with and including multistranded copper conductor 2.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed FRLS cable 1100 Volts grade, ISI marked with valied CML number drawn in and including medium grade PVC casing and capping double lock type 32mm in size, fire resistant, ISI marked including with its fittings and fixtures such as tees, bends, elbows, junction boxes, etc. including multistranded copper conductor 1.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed FRLS cable 1100 Volts grade, ISI marked with valied CML number as continuity earth wire and including pressed steel sunken concealed terminal box with 3mm thick industrial laminated sheet cover for mounting switches, sockets and fan regulators etc. for one 3 pin, 15 Amps socket outlet point on independent board complete all as specified and directed.

M&L for wiring with and including multistranded copper conductor 4 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed FRLS cable 1100 Volts grade, ISI marked with valied CML number in and including medium grade PVC casing and capping double lock type 32mm in size, fire resistant, ISI marked including with its fittings and fixtures such as tees, bends, elbows, junction boxes, etc. including multistranded copper conductor 2.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed FRLS cable 1100 Volts grade, ISI marked with valied CML number as continuity earth wire and including pressed steel sunken concealed terminal box with 3mm thick industrial laminated sheet cover for mounting switches, sockets and fan regulators etc. for one 3 pin, 15 Amps socket outlet point on independent board complete all as specified and directed.

Supplying & laying, XLPE insulated, PVC inner sheathed, armoured with galvanised steel strip or wire heavy duty underground cable with aluminium multi stranded conductor, 1100 volt grade, laid in trenches/duct, passing through pipe/duct or fixed on pole and connecting and testing complete including taking down old unserviceable cable all as specified and directed of 16 Sqmm, 2 core sizes of cable.

Supplying & laying, XLPE insulated, PVC inner sheathed, armoured with galvanised steel strip or wire heavy duty underground cable with aluminium multi stranded conductor, 1100 volt grade, laid in trenches/duct, passing through pipe/duct or fixed on pole and connecting and testing complete including taking down old unserviceable cable all as specified and directed of 25 Sqmm, 4 core sizes of cable.

S&F, switch piano, flush button, single pole, one way, 5 Amps complete all as specified and directed

S&F, switch piano, flush button, single pole, one way 15 Amps complete all as specified and directed

S&F, in repair, 1x9 watts, bulk head luminaires deep drawn anodised body, epoxy white powder coated, heat resistant , prisamatic glass cover with specially designed gasket, including CFL lamp 9 Watt, and connecting up with twin core twisted flexible copper cable of suitable size and testing on completion all as specified and directed.

S&F, in repair, CFL light fitting, 1x11 w attractive wall/ceiling mounted type with metallic channel and white reflector, suitable for mirror fittings with ballasts, lamp holders, connector block, etc. complete with all accessories pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size.

S&F, socket outlet, 2 in 1, 3 pin, 15 Amps and 5 Amps flush type complete all as specified and directed

S&F, socket outlet, 2 in 1, 3 pin, 5 Amps, flush type complete all as specified and directed

S&F, in repairs, sheet metal enclosures single pole & neutral with a two pin & earth plug and socket complete with one single pole, MCB of 20 Amps, 10 KA, 240 volts complete all as specified and directed

S&F, in repairs, sheet metal distribution board, factory made and tested complete, protection class IP-42 suitable for mounting MCBs, isolator with 200 A tinned copper bus bar of capacity 200 Amps of SPN, 4 way 240 Volt complete all as specified and directed

S&F, in repairs, sheet metal distribution board, double door factory made and tested complete, protection class IP-42 suitable for mounting MCBs, isolator with 200 A tinned copper bus bar of capacity 200 Amps, SPN, 8 way 240 Volt complete all as specified and directed

S&F, ceiling rose, 3 terminal , any shade, of PVC/Polycarbonate, isolated body complete all as specified and directed

S&F, in repair, angle holder, insulated body with back plate for batten fitting including 12 W LED bulb complete all as specified and directed.

S&F, in repair/replacement, LED light fitting, batten type, 1 x 20 watt including lamp and connecting up complete with white PVC insulated and PVC sheathed round flexible twin core copper conductor cable of suitable size and testing on completion all as specified and directed. Make : Bajaj or equivalent make in Havells.

S&F, in repair, Surface and wall mounted LED batten, 1 x 20 W, extruded aluminium housing provided for efficient heat dissipation with poly carbonate diffuser & integrated electronic driver, 4 feet long. all as specified and directed. Make as approved by GE from the make specified in Appx 'C.

S&F, in repairs, LED light fitting, batten type, 1 x 18 or 1 x 20 watt with PVC insulated and PVC sheathed round flexible copper conductor cable of suitable size and tensting on completion all as specified and directed of make Bajaj or equivalent make as approved by GE from the makes specified under Appx 'C'.

Taking down carefully old unserviceable tube light fitting/holder/bulk head, including fixture and fitting such as ceiling roses etc. complete all as specified and directed.

Taking down carefully old unserviceable MCB/MCCB including fixture, complete all as specified and directed.

Taking down carefully old unserviceable DB Box of any type/size including fixture complete all as specified and directed.

S&F, Exhaust Fan, 350mm Sweep, single phase, 230 volts, 50 Hz, including making opening for exhaust fan including grouting nut , bolts and washer for fixing of fan and making good the disturbed surfaces all as per existing and mounting fan including connected with three core copper conductor cable 0.75mm complete all as specified and directed .

S&F, Exhaust Fan, 250mm Sweep, single phase, 230/240 volts, including making opening for exhaust fan including grouting nut, bolts and washer for fixing of fan and making good the disturbed surfaces all as per existing and mounting fan including connected with suitable three core copper conductor cable complete all as specified and directed. Make as approved by GE from the make specified in Appx 'C'.

Supplying, installation and testing of water storage heater (Geyser) 25 Ltr capacity, BEE, 5 star rated, energy saving, metal body with glasslined steel inner tank, verticle type, having autocut off system, including making necessry connection to inlet and outlet pipes with and including 15 Amps plug top and 3 core copper conductor multi stranded PVC insulated and sheathed cable of length 1.5 M complete all as specified and directed.

Taking down ceiling fan with single phase step type regulator, AC 230/240 Volts, 50 Hz, 1200mm sweep, with sealing cable end, and blades and refixing the fans complete all as specified and directed.

S&F, Isolator, type curve ‘C’ , 10 KA, SP, 6 to 40 Amps complete all as specified and directed.

S&F, Isolator, Single pole and neutral, type curve ‘C’ 10KA, 32-40 Amps 230 Volts. complete all as specified and directed.

M&L for hanging only ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan complete all as specified and directed.

S&F, in repairs, stepped type electronic fan regulators, 120W/280V complete all as specified and directed. Make- Anchor Cat No. 33070 or equivalent as approved by GE.

S&F, in repairs, sub-main wiring with 2 single core, 4 Sqmm PVC insulated, unsheathed, 1100 Volts grade, FRLS, copper multi stranded conductor drawn in and including PVC concealed conduit and conduit acessories including drawing one run of PVC insulated, unsheathed, 1100 Volts grade, FRLS, copper conductor multi stranded, 2.5 Sqmm size as continuous earth wire drawn through and connected to main switch/DB and testing on completion complete all as specified and directed. Note: (i) 2 runs of main conductor, one run of earth conductor and one run of PVC conduit and acessories shall be measured as one unit length.(ii) Rate quoted shall deemed to includes cuttings chases for consealing PVC conduit and making good the disturbed surfaces in CM 1:3 complete.

S&F, sub-main wiring with 2 single core, 6 Sqmm PVC insulated, unsheathed, 1100 Volts grade, FRLS, copper multi stranded conductor drawn in and including PVC casing and caping of 32mm size including drawing one run of PVC insulated, unsheathed, 1100 Volts grade, FRLS, copper conductor multi stranded, 4 Sqmm size as continuous earth wire drawn through and connected to main switch/DB and testing on completion complete all as specified and directed. Note: 2 runs of main conductor, one run of earth conductor and one run of PVC casing and caping shall be measured as one unit length.

M&L,earthing complete with galvanized steel earth plate electrode of 60 cm x 60 cm x 6mm thick buried directly in ground [earth pit not less than 2.25 metre deep below normal ground level] with top edge of the plate not less than 1.5 m below normal ground level, connected to galvanized earth wire of 4mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical plate No. 3 of MES SSR Part I all as specified and testing on completion including provision of earth lead protected by 15 mm dia light grade GI pipe & watering pipe shall be 20 mm bore medium grade GI pipe including all excavation and earth work in any type of soil, PCC pit with RCC cover, char coal, salt, funnel etc complete. Note : Rate quoted by tenderers shall be deemed to include for following provisions;-[i]. Excavation & earth work in any type of soil including removing of surplus material upto 50 M.[ii]. PCC 1:3:6 type C1 using 20mm graded stone aggregate in pit & 40mm thick precast RCC 1:2:4 type B1 cover 50x50 cm with 8mm TMT bars @ 10 cm C/C both ways with handles.[iii]. Main earthing lead from earth electrode to test point upto 7.5 mtr.[iv]. Funnel with watering pipe [GI pipe] 20mm bore [ISI marked] medium grade & copper lugs, charcoal & salt as reqd.[v]. GI protection pipe of size 15 mm bore light grade 7.5m.

partechengineers

nirman construction