REPAIR TO STREET LIGHT IN AOR OF GE (A) AHMEDABAD

Amount

Excavation in soft / loose soil in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth and getting out in soft / loose soil complete all as specified and directed.

Returning filling with earth obtained from excavation including spreading watering and consolidation in layers not exceeding 25 cms thick complete all as specified and directed

Removing surplus soil to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed

S&F steel tubes light grade galvanized 40 mm bore ISI marked with all fittings fixed to walls / floors / road crossing, poles as required complete all as specified and directed

Supplying, laying or fixing or passing through pipe, testing and commissioning in renewal 1100 volts grade ISI marked XLPE insulated and PVC sheathed steel tape / wire armoured underground stranded aluminium conductor cable of size 10 sqmm 4 core complete all as specified and directed

Supply and erection in vertical position Steel tubular swaged poles complete with cast iron base plate, finial taper plug, bolts, nuts and screws, type 410 SP-31 (9.00 meter long) all as specified duly factory painted with two coats of black bituminous paint internally through out and externaly for embeded portion and painting with one coat of red oxide primer, applying two coats of synthetic enamel aluminium paint on remaining exposed surfaces after errection complete, painting with synthetic enamel paint of colours black and yellow alternate strips of 30cm width upto 1.5 mtr from the top of coping complete including making suitable holes where required all as specified and directed and including the following:-

Excavation in post holes in any type of soil not exceeding 0.6 cum each, getting out, returning filling in and ramming earth in layers not exceeding 25 cm thick watering and disposal of surplus soil to a distance not exceeding 50 m and making good surface complete.

PCC (1:4:8) type D2 using 40 mm graded stone aggregate in base (0.60 m x .60 m x 1.5 m height).

PCC (1:3:6) type C2 using 40 mm graded stone aggregate in foundation filling (0.60 m x .60 m x 1.5 m height).

PCC (1:2:4) type C2 using 40 mm graded stone aggregate in coping (0.60 m x 0.45 m height).

Pole cap 0.30 m long externally fitted on pole top duly welded with a light grade ISI marked GI pipe bracket 1.5 m long for mounting street light fitting.

Painting with aluminium paint one under coat, one finishing coat over a coat of red oxide primer and making alternate colour bands of black & white colours in 30 cms width upto a height of 1.5 m from pole coping with synthetic enamelled paint complete.

Dismantling unserviceable broken or damaged concrete poles, 9.00 m long complete all as specified and directed

Supply and laying sub class 'B' bricks of old size (230x115x75 mm) or of size locally available , laid along alignment of cable as protection to cable in trenches complete all as specified and directed by Engineer-in-Charge

M & L for good quality dry sand cushioning to under ground electric cable on layer of 8 cm thick before laying the cable and second layer of 15 cm thick after laying the cable all as specified in clause 19.75 of MES Schedule part-I (2009) Note : Sand shall be fined sand as specifed and punned thickness shall be measured and paid.

Taking down any type HPSV fittings andSupply, installation, testing and commissioning LED street light fitting including driver with energy saving and enviornmental friendly made up of pressure die cast aluminium housing with high power LED 70 Watt as lighting conforming to IS-10322 (Part 5/Section 3) 2012 and lens embedded PC cover having TOP Opening seperate driver compartment with IP66 protection and IK07 with 10KV inbuilt Surge protection device Reqmt of all sundry items ie three core copper wire 1.5 Sqmm PVC sheathed, insulation tape, screw, clamps, nuts and bolts for fixing of street light with dismantling are to be included in quoted rate. Make - Havells, Cat No Endura Cityliner Neo 70W/72W NDPD / Philips Crompton Cat No LST-70-CDL-M or equivalent GE lighting as approved by GE.

Taking down any type HPSV fittings andSupply, installation, testing and commissioning LED street light fitting including driver with energy saving and enviornmental friendly made up of pressure die cast aluminium housing with high power LED 90 Watt as lighting conforming to IS-10322 (Part 5/Section 3) 2012 and lens embedded PC cover having TOP Opening seperate driver compartment with IP66 protection and IK07 with 10KV inbuilt Surge protection device Reqmt of all sundry items ie three core copper wire 1.5 Sqmm PVC sheathed, insulation tape, screw, clamps, nuts and bolts for fixing of street light with dismantling are to be included in quoted rate. Note :- (i) Minimum 2 years gaurntee period of LED fittings (ii) Driver shall be IP 65 degree of protection potted seal type. (iii) System lumen output should be greater than 100 lum/watt(iv) LM79 &LM80 test report from NABL accredited lab should be submitted by contractor before incorporation of material. Make - Havells PEARLMAGNUMSL90WLED757PASYTOTG / Crompton Cat No LSTP-90-CDL-A or equivalent in Wipro as approved by GE.

M&L for taking down any type of unserviceable post top light and S&F of LED post top lantern energy saving, with symmetrical light distribution, spun aluminium canopy with clear acrylic diffuser, high power LED 25 watt and fixing accessories complete. Make - Havells / Crompton /C&S/Wipro.

Supply and fix in replacement LED flood light fitting 70 Watts, having Pressure die cast housing with IP66 Efficient , protection with heat resistant toughned glass with individual LED lenses(Non COB) complete,including MS Clamps,nut and bolt, making connection with street light box or OH line using PVC insulated and sheathed single core multi stranded alumn conductor cable of size 1.5 Sqmm all as directed by Engr-in-Charge. Make: Havells JETA FLARE 70 or equivalent inCrompton /Philips/ GE Lighting Note :- (i) Minimum 2 years gaurntee period of LED fittings (ii) Driver shall be IP 65 degree of protection potted seal type. (iii) System lumen output should be greater than 100 lum/watt(iv) LM79 &LM80 test report from NABL accredited lab should be submitted by contractor before incorporation of material.

Supply and fix in replacement LED flood light fitting 120 Watts, having Pressure die cast housing with IP66 Efficient , protection with heat resistant toughned glass with individual LED lenses(Non COB) complete,including MS Clamps,nut and bolt, making connection with street light box or OH line using PVC insulated and sheathed single core multi stranded alumn conductor cable of size 1.5 Sqmm all as directed by Engr-in-Charge. Make: Crompton Cat no LFLN-120- CDL or equivalent in Havells /Phillips / GE lighting Note :- (i) Minimum 2 years gaurntee period of LED fittings (ii) Driver shall be IP 65 degree of protection potted seal type. (iii) System lumen output should be greater than 100 lum/watt(iv) LM79 &LM80 test report from NABL accredited lab should be submitted by contractor before incorporation of material.

Taking down of HPSV/MV/MH flood light and Supply and fix in replacement LED flood light fitting 200 Watts, having Pressure die cast housing with IP66 Efficient , protection with heat resistant toughned glass with individual LED lenses(Non COB) complete,including MS Clamps,nut anf bolt, making connection with street light box or OH line using PVC insulated and sheathed single core multi stranded alumn conductor cable of size 1.5 Sqmm all as directed by Engr-in-Charge. Make: Crompton Cat no LSFO-200-CDL/60 or equivalent in Philips/ GE Lighting/Havells. Note :- (i) Minimum 2 years gaurntee period of LED fittings (ii) Driver shall be IP 65 degree of protection potted seal type. (iii) System lumen output should be greater than 100 lum/watt(iv) LM79 &LM80 test report from NABL accredited lab should be submitted by contractor before incorporation of material.

Supply and fix in repairs Polystyrene body IP 65 cable junction box with connector metric knockouts on all sides for cable entry including cable glands,sizeof junction box 200 x 160 x 98 mm as per Hensel cat ref no. K 9255 or equivalent duly fitted with followings:-

ELMEX or equivalent make end plate - 1 No

ELMEX or equivalent make end clamps - 2 Nos

Clamp made of 30x5 mm flat iron duly painted with two coats of aluminium paint over a coat of red oxide primer suitable for steel tubular swaged pole type 410 SP-31.

S&F in repairs street light bracket made of GI pipe light grade bend in shape of 40 mm dia, 1.5 m long and clamped with 2 pairs of 40 x 6 mm flat iron clamps, nuts / bolts / washers & painted with 2 coats of aluminium paint over a coat of red oxide primer on clamps complete all as specified and directed

Supply and fix Pole cap 0.30 m long externally fitted on pole top duly welded with a light grade ISI marked GI pipe bracket 1.5 m long for mounting street light fitting complete all as specified and directed

Supply only PVC insulated & sheathed, multistranded copper conductor industrial cable 1.5 sqmm three core 1100 volt grade from Junction box to street light fitting as required.

Painting of street light swaged poles 8.5 m / 9.0 m long including street light brackets/clamps etc with best quality aluminium paint, making alternate black & white colour bands of 30 cms width upto a height of 1.5 m from pole coping with synthetic enamelled paint complete all as specified and directed

Labour & tools for trimming tree branches upto 100 mm girth of any location around existing LT street light poles giving clearance of 1.5 m on all sides complete. (Note:- Trimming of tree branches irrespective in numbers in each tree shall be measured as one unit).

Labour and tools for rectification of defects in any type of street light fittings / security light fittings under GE (A) Ahmedabad cantonment including sundry items like insulation tapes, nuts, bolts, washers, holders of LED /HPSV/ MH/T5 fittings, LED driver, starters & bipin holders of tube light fittings as required. (Note :- Items other than sundry items mentioned above required for repair / renewal to make functional street lights shall be measured & paid separately against item no 19,24 & 25 as supply only but labour cost of their renewal is included in this item).

Supply only Electronic LED Driver Suitable for 45 Watt street/Flood lights fitting complete all as specified. Make: Crompton /Philips/Havells / Wipro.

Supply only Electronic LED Driver Suitable for 70 Watt street/Flood lights fitting complete all as specified. Make: Crompton /Phillips/Havells/Wipro

M&L for traffic light & alternate flasher/Traffic blinker LED more than 250 CDL & No of LED more than 108/12V solar plate charging current >= 500 MA, LED color yellow/Red/Green with battery backup 12V/7.5 AH 24 Hrs Atonomy, auto on/off function with high & low voltage cut off with dawn dusk function inbuilt and mounting on GI pole 80mm dia making necessary connection with suitable size of 4 sqmm cable. Make:- Intersolar or equivalent.

Taking down street light fitting or flood light fitting any type and any rating from poles, walls or any other indicated situation/location after disconnecting electrically. seggregating serviceable and unservicable fittings. Keeping aside serviceable for reuse at same location or any other location with in the zone and removing unserviceable from site.

Labour & tools for horizontal boring through road / path / floor for passing UG cables by using trench less technology for laying upto 100mm dia pipe complete all as required. Note : GI / DWC pipe will be measured and paid seperately.

S&F rigid non metallic PVC conduit 20mm dia medium grade ISI marked ivory colour alongwith accessories for fixing on pole/laying in garden including minor excavation for protection of service wire / cable complete all as directed.

S&F framed work such as grills, gratings etc, with ends of bars shouldered and/or reveted or forged into spikes, framed guard bars frame work of piller lights and similar work conforming to Fe 290, Gde E-165 complete all as directed.

M&L for fabrication of welded steel wire fabric supplied and fixed complete to steel members not exc to 4 kg per sqm size as per site requirement complete all as directed.

SATISH ELECTRICALS

Electricals India