As per NIT

Amount

Dismantling & taking out LT burnt cable ends of any size from transformer/LT panel/LT feeder pillar/ street light pole box/trenches any type/size, for repair/making suitable for reconnection to cable, providing lugs to burnt end of cables, preparing fresh terminals and reconnection, fixing the removed portion of cable with transformer/in trenches/along pole/ panel/feeder pillar box, including excavation of loop & refilling complete using old bricks and sand returning filling the excavated soil complete all ss specified and directed.

S&F (in replacement) following items in the existing out door/ indoor LT panels and connection with using aluminum lugs/ferruls incl disconnection & connection of cable and making necessary alteration in panel/door using welding wk and cutting as required for proper fixing & connection complete all as specified and directed as below :- (Note :-Make of MCCB/MCB : Schneider/L&T/ABB)

(a) MCCB 4 Pole 63 amps rating, 16 KA breaking capacity, 415 Volt

(b) MCCB 4pole 100 amps rating, 16 KA breaking capacity with spreader at bothe side

(c) MCCB 4 pole150/160 amps rating, 36 KA breaking capacity with spreader at bothe side

(d) MCCB 4 pole 200 amps rating, 36 KA breaking capacity with spreader at bothe side

(e) MCCB 4 pole 250 amps rating, 36 KA breaking capacity with spreader at both side .

(f) MCCB 4 pole 400 amps rating, 36 KA breaking capacity with spreader at bothe side

(j) CTs of existing ratio and capacity fixed in LT panels and connect with ammeter .

(k) Indicator lamp, LED type incl 1.5 sqmm wire for connection to desired point of bus bar.

(l) MCB TPN 63 amps, 'C' series, 415 volt

M&L for boring under road horizontely of size 50/80 mm bore of GI pipe for passing of cable in road in hard/soft/ loose soil complete all as specified and directed.

Disconnecting & dismentling of damaged/unsv cable any type /make and Supply & laying (in repair) cable XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor using lugs bothe end of cable& wrapping pvc tape over XLPE insulation cable and testing complete all as directed for following size :- (Note :- Excavation & earth work, sand cushioning, bricks protection & GI pipe where required shall be measured & paid seperately)

(a) 240 Sqmm 3.5 core

(b) 16 Sqmm 4 core

(c) 70 Sqmm 3.5 core

Excavation in trenches in hard/dense soil not exceeding 1.50 Mtrs wide and not exc. 1.5 Mtr deep and getting out for taking out/laying cable, poles &stay etc complete all as specified and as directed by Engr-in-Charge.

Returning, filling in including spreading leveling, watering and well ramming in layers not exc 25 cm thick after the cable have been laid tested complete all as specified and as directed by Engineer-in-Charge.

Removal of excavated surplus soil to a distance not exc. 50 Mtrs and depositing where directed at a level not exc 1.5 Mtr above the starting point complete all as specified and as directed by Engr-in-charge.

M&L for sand cushioning to under ground cable provided with layer of sand (8cm deep before laying the cable and 15 cm deep after laying the cable ie total 23 cm.

M&L for brick laid in trenches for cable protection of burnt clay sub class ‘B’ complete laid dry flat.

M&L(in replacement) for laying of GI Pipe medium grade of 50 mm bore dia in trenches /under road crossing/fixed on pole/wall/under floor including suitable mild steel FI clamps of required size complete all as specified and as directed by Engineer-in-Charge

Servicing/overhauling of servo voltage stablizers of ranging from 30 KVA to 150 KVA capacity , detection of defective components, replacement of worn out parts and servicing/ cleaning of mechanical components after drawout of coil if required and Testing for smooth operation after caliberation of relay trough OEM of servo/ and resetting the system & setting for healthy system, complete all as specified and directed by Engr-in-Charge. Note: Worn out parts shall be deemed to be included in quoted rate and Major parts shall be measured and paid separately are as under:

Supply only spare parts for servo stablizers of any make (30 - 150 KVA) all as specified :-

Digital control card of servo as per existing make.

R C network of servo complete all as required and directed at site complete all as per sample.

Servo motor complete all as required and directed at site complete all as per sample.

Micro switches complete all as required and directed at site complete all as per sample.

Voltage regulating coil complete all as required and directed at site complete all as per sample.

M&L Servo stablizer oil having di-electric strength of 60 KV as per IS complete for top up/ replacement all as specified and as directed by Engr-in-Charge. (Oil should be supplied in sealed barrel) Note: oil shall be filled in the transformers/stabilizers to be repaired or installed at site at different locations.

Supply and fixing of 30HP Soft Starter with Wall Mounting Panel consist of following items as under : 1. MCB 4P 100 A -01 2. Soft starter, Altistart 480, 45 A, 208 to 690V AC, control supply 110 to 230V AC -01, 3.Contactor 65 A 4. Push Button and Indicator 5. MS Powder Coated Complete wired up Starter Panel Approx HWD 600*600*300 - 01

Supply and fixing in replacement of sheet metal encloser of 100 Amps capacity

Supply and fixing in replacement of sheet metal encloser of 63 Amps capacity

Material and labour for earthing complete with copper earth plate electrode 600 mm x 600 mm x 3.15 mm thick burried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of the plate not less than 1.5 metre below normal ground level connected to copper earth strip 20x3mm size (upto 7.5 metre from ground electrode) by means of copper/brass bolts, nuts, check nuts and washers all as shown in electrical plate No.3 of MES Schedule Part-I, connected to earth test terminal block and testing on completion with and including 40mm bore light grade GI protection pipe for strip upto plingth protection, PCC pit in mix 1:3:6 type C1, with RCC 1:2:4 type B-1, 40 mm thick cover, reinforced with 6 mm dia MS bars 3Nos. both ways with lifting hook made out of 6 mm dia bar, watering arrangement with funnel and wire mesh and 20 mm bore medium grade GI watering pipe, common salt and charcoal filling, necessary excavation and earth work complete.

Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised iron strip 25×4mm as earthing lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion as specified and directed at site

RAMSONS DEVELOPERS (BID ID -3351742)

JAGAT POWER ELCTRICAL (BID ID -3359485)

M/S BHATT ENTERPRISES (BID ID -3359449)

SONI ENTERPRISES (BID ID -3351148)