SPECIAL REPAIR TO OTM ACCN BUILDING NOS T 163 AND T 164 AT SUPPLY DEPOT AND MD ACCN BUILDING NOS P 19 P 20 AND P 21 OF 9 JAT AT DOGRA LINES IN THE AREA OF AGE BR III UNDER GE ROORKEE

Amount

Demolition of cement concrete (Un-reinforced) including tiles/kota etc in ground floors and paving n.exc. 15cm thickness (below or above ground level) and removal of rubbish outside defence land complete all as specified and directed.

M&L for grinding and polishing existing kota stone flooring / dado/ skirting to give mirror finish complete all as specified and directed.

M&L for 20 to 25 mm thick machine cut kota stone slab, laid over and including 15mm thick screed bed or bedding layer in cement mortar (1:6) in flooring, set and jointed with neat grey cement slurry and pointed with grey cement mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and directed.

M&L for 20 to 25 mm thick machine cut kota stone slab, laid over and including 10mm thick screed bed or bedding layer in cement mortar (1:4) in vertical surfaces as in steps, skirting, dado and the like, set and jointed with neat grey cement slurry and pointed with grey cement mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises and M&L Non - skid Ceramic coloured joint free tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, laid over and including 15mm thick screed bed in cement mortar (1:6) in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises andM&L for glazed ceramic colour joint free tiles in vertical surface size 450X 350X 7 mm/ 450x 300 x7mm thick as required, laid over and including 10mm thick backing coat in cement mortar (1:4), set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L for 18-20 mm thick granite stone slab (table rubbed and polished), laid over cooking platforms and the like over and including 15mm thick screed bed in cement mortar (1:6) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of marble slab including moulding of exposed edges and cutting chases in existing walls, if required, complete all as specified and directed.

M&L for 75 mm thick cement concrete (1:3:6) type C2, (using 40 mm graded stone aggregate) as in plinth protection, laid in panells n.exc 2.50 Sqm each and finishing the exposed surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for chequered cement concrete tiles of size 20cm x 20cm x 25mm thick with grey cement and no pigment, laid over and including 15mm thick screed bed or bedding layer in cement mortar(1:4), set and jointed in neat grey cement slurry and pointed in grey cement mixed with pigment to match the shade of tiles complete all as specified and directed.

Dismantling wall and ceiling board (fibre, pulp, insulation etc) or insulation boards/ slabs any thickness complete all as specified and directed.

M&L for providing and fixing tiled false ceiling of designer tiles(high pressure steam Cured) of 4mm thickness (as per IS:14862) of size 595x595mm and any one of the design ( Cascade or Electra or equivalent) in true horizontal level, suspended on inner locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grms, both side inclusive and black painted groove on all T webs) consisting of main “T” runner with suitably spaced joints to get required length and 15x32mm made from 0.3mm thick sheet, 1200mm long spaced between main “T” at 600mm C/C to form a grid of 1200x600mm and secondly cross “T” of length 600mm and size 15x32mm made of 0.30mm thick sheet to be interlocked at middle of 1200x600mm panel to form grids of 600x600mm and wall angle 15x20x0.36mm and laying false ceiling tiles in the grid including, required cutting / making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI soffit cleats fixed to existing RCC lintel with dash fasteners, GI adjustable rods of 3mm dia with galvanized butterfly level clips, spaced at 1200mm c/c along main “T”, bottom exposed width of 15mm of all “T” sections shall be pre-painted with polyester paint and black painted groove at center of size 4mm depth and 4.5 mm width, fixed at any height complete all as per directions of Engineer-in-Charge.

Dismantling asbestos cement (corrugated, semi corrugated etc) sheets in roof covering complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed

S&F for pre-painted galvalume aluminium zinc cozting GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed

M&L for rolled mild steel work in tubular trusses including special shaped washer etc using ERW or induction butt welded tubes conforming to IS-1161-1998 Grade St-240 complete all as specified and directed

Demolition of brick work or stone / boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facings / dressed stone work and precast concrete articles etc complete all as specified and directed

M&L for brick work with old size sub class 'B' bricks built in cement mortar (1:6), straight or curved on plan exc 6m mean radious complete all as specified and directed

M&L for brick work with old size sub class 'B' bricks in half brick thick walls, built in cement mortar (1:6), straight or curved on plan in any radius complete all as specified and directed.

Demolition of RCC of any description and in any position and M&L for precast cement concrete (1:2:4) type B1(using 20mm graded stone aggregate) in landings, cover slabs for manholes, kitchen platform and similar articles with plain fair faces including chamfers, weathering, throating etc and setting in cement mortar (1:6) with joints to match complete all as specified and directed.

M&L mild steel TMT bars 10 mm dia and over cut to length, bent to shape required including cranking, bending, hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L for cement concrete (1:2:4) type B0 (using 12.5mm graded stone aggrgate) in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed.

Taking down cement or cement lime plaster on brick or stone walls etc incl raking out joints, hacking for key, scrubbing down with water etc and M&L for 15 mm thick rendering in cement mortar (1:6) on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

Taking down cement or cement lime plaster on brick or stone walls etc incl raking out joints, hacking for key, scrubbing down with water etc and M&L for 15 mm thick rendering in cement mortar (1:4) on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar (1:6) on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L for 10mm thick plastering in cement mortar (1:4) on fair faces of concrete surfaces of ceiling complete all as specified and directed.

Taking up or down 15mm dia steel tubing and connections, including cleaning for refixing or removal to store and S&F new 15mm dia bore GI tubing (ISI marked) medium grade with all fittings and fixed to walls and ceiling or laid under floor including connection etc including cutting chases exc 10 cm but n.exc 20 cm in wall for concealing of pipe (if required) and making good in cement mortar (1:3) to match the existing surfaces complete all as specified and directed.

Taking up or down 20mm dia steel tubing and connections, including cleaning for refixing or removal to store and S&F new 20mm dia bore GI tubing (ISI marked) medium grade with all fittings and fixed to walls and ceiling or laid under floor including connection etc complete all as specified and directed.

Taking up or down 15mm dia steel tubing and connections and refixing in new or old position including cleaning for re-fixing or removal to store including replacement of unserviceable fittings and cutting chases and making good in cement mortar (1:3), if required to conceal the tubing complete all as specified and directed.

Taking up or down 20mm dia steel tubing and connections and refixing in new or old position including cleaning for re-fixing or removal to store including replacement of unserviceable fittings complete all as specified and directed.

S&F in repairs, 20 mm dia bore gun metal globe / gate valve with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed

Dismantling of water storage tank of any description of 1000 ltrs capacity and removing to store and S&F new 1000 ltrs Rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position including 20mm ball valve high pressure of PTMT with epoxy coated aluminium rod & high desity plastic ball (minium weight 20mm-210gms) and 20mm dia bore GI hexa nipple etc complete all as specified and directed.

Dismantling of water storage tank of any description of 500 ltrs capacity and removing to store and S&F new 500 ltrs Rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position including 20mm ball valve high pressure of PTMT with epoxy coated aluminium rod & high desity plastic ball (minium weight 20mm-210gms) and 20mm dia bore GI hexa nipple etc complete all as specified and directed.

S&F in repairs, vitreous china wash hand basin, white, flat back size 550x400mm (excluding taps, chain and plug) including a pair of MS bracket duly painted, 32 mm size brass CP waste coupling and 32 mm dia PVC waste pipe etc and fixied in position complete all as specified and directed.

S&F in repairs,15mm dia PVC connection 450mm long with PTMT nuts and nylon washers at both ends complete all as specified and directed.

S&F in repairs, 15 mm dia bore brass CP pillar tap (with Aerator) with long screwed shank & fly nut, capstan head, screwed down, high pressure with or without lettered hot or cold complete all as specified and directed.

S&F in repairs, 15mm dia bore stop/ angle cock, fancy type, chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both ends suitable for iron pipe of 15 mm bore complete all as specified and directed.

S&F in repairs, 15mm dia bore brass chromium plated stop/ angle cock, fancy type with long shank and cup (concealed type), screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or unions and fixed complete all as specified and directed.

S&F in repairs, 125 mm size brass chromium plated shower rose (single lever over head shower including shower arm casted 190 mm long flat shape with flange) suitable for 15 mm dia bore pipe complete all as specified and directed.

S&F in repairs, 15mm dia bore brass chromium plated bib tap (short body), fancy type with crutch or butterfly handle, screwed down high pressure complete all as specified and directed.

S&F in repairs, viterous china wash down water closet pan (Pedestal pattern) white with 'P' or 'S' trap and plastic water closet (EWC) seat cover white closed pattern and making good the disturbed surface to match with the existing complete all as specified and directed.

S&F in repairs, vitreous china squatting pan 'Orissa pattern' long pan of size 580x440mm white, with integral footrest & 'P' or 'S' trap including connection to trap, flushing pipe, anti-syphonage pipe etc and making good the floor to match with the existing surfaces complete (excluding flushing cistern and flush) complete all as specified and directed.

S&F in repairs, 10 ltrs PVC (White) valve less syphonic action type, flushing cistern low level with inlet ball valve float, handle, aluminium brackets for bottom support, fixing with gitties embeded in wall with drilling machine etc complete all as specified and directed.

S&F in repairs, stainless steel sink without draining board, made out of 1.00mm thick stainless steel sheet for kitchen or laboratory, overall size 915mm x 460mm with bowl size 410mm x 330mm x 160mm, with plug, waste fittings, waste pipe, washers including cantilever type cast iron brackets duly painted, connecting union etc complete all as specified and directed.

S&F in repairs, shelf of PTMT fixed with and including chromium plated brass screw and wooden /plastic cleats etc complete all as specified and directed.

S&F in repairs, towel rail 600mm long 20mm dia brass chromium plated with brackets,fixed with wooden guities embeded in cement mortar (1:3) with steel screws etc, complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) area n.exc 1.50 Sqm each complete all as specified and directed.

S&F steel window with side hung shutters including projecting/box type hinges with steel handle, tower bolt and steel peg stay complete with glazing bars dovetailed or welded complete all as specified and directed.

S&F steel window with side hung shutters including projecting / box type hinges with steel handle, tower bolt and steel peg stay without glazing bars complete all as specified and directed.

S&F Steel ventilator with top hunge shutters including hinges and steel peg stay with or without glazing bars dovetailed or welded complete all as specified and directed

S&F mild steel framed work such as grills, gratings with ends of bars shouldered and or riveted or forged into spikes, framed guard bar, barred iron door, ladders, hold fast, framed balusters, walk ways, railings, frame work of water tank and similar work conforming to Fe 290 Gde E165 complete all as specified and directed.

S&F 3 mm thick plain, ordinary quality sheet glass and glazing with oil putty or fixed with wooden beads in square not exc 0.5 Sqm in each pane complete all as specified and directed.

S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanised wire staples complete all as specified and as directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed in position complete all as specified and as directed.

M&L for preparing new steel and iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enemel paint over a coat of red oxide primer complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) area exc 1.50 Sqm but n.exc 4.00 Sqm each complete all as specified and directed.

Taking down shutters of any description exc 1.00 Sqm and n.exc 2.00 Sqm each complete all as specified and directed.

S&F pressed steel frame of size 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock / strike plate etc complete all as specified supplied and fixed.

M&L for cutting holes in brick walls exc half brick thick but n.exc one brick thick wall built in cement mortar or cement lime mortar and stone walls built in lime mortar for inserting holdfasts and making good dismantled portion in cement mortar (1:3 ) or cement concrete (1:2:4) type B1 as required complete all as specified supplied and fixed.

S&F 30 mm thick flush shutter, solid core construction with particle board core and plywood face panels, commercial type on both sides and fitted to chowkat complete all as specified and directed.

S&F factory made 35 mm thick 2nd class HW glazed and skeleton door shutters, open rebated and prepared to receive glass, gauze, etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc, sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed .

S&F factory made 35mm thick IInd class hard wood plain framed panelled shutter (any numbers of panels) with lock rail & panel of 9mm thick B.W.P. commercial ply or 12mm thick veneered particle board with commercial veneers on both faces. The size of rail as per IS: 1003 (Part-I), kiln seasoned & chemically pressure treated complete all as specified and directed.

S&F factory made solid PVC door frame of size 50 mm x47mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specification and shown on drawing complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. Frame for top and bottom rails . M.S. Frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail, and bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, supplying and fixing in the frame at site as per specifications and shown on drawing complete all as specified and directed.

S&F 150 mm long floor door stopper of aluminium alloy body tongue, anodised, with hard drawn steel spring fixed to door

S&F 125mm size butt hinge extruded aluminium alloy with galvanized mild steel hinge pin anodised and fixed complete all as specified and directed..

S&F 100mm size butt hinge extruded aluminium alloy with galvanized mild steel hinge pin anodised and fixed complete all as specified and directed..

S&F 125mm size aluminium alloy handle, fabricated type extruded section (ISI marked) complete all as specified and directed..

S&F 100mm size aluminium alloy handle, fabricated type extruded section (ISI marked) complete all as specified and directed..

S&F 200mm size aluminium anodized barrel tower bolt of extruded section and fixed complete all as specified and directed..

S&F 150mm size aluminium anodized barrel tower bolt of extruded section and fixed complete all as specified and directed.

S&F 250mm long alumnium alloy anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section complete all as specified and directed.

M&L for preparing new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enemelled paint over a coat of pink primer complete all as specified and directed.

S&F in repairs, 19 to 20mm dia bore stainless steel pipe fixed in required length as in curtain rod etc complete all as specified and directed.

S&F in repairs, coloured stainless steel curtain rod brackets and stainless steel knob, fancy type suitable for 19mm/20 mm dia bore curtain rod complete as specified and directed.

S&F in repairs, 20 mm dia mild steel pipe covered with PVC sleeves fancy type curtain rod with and including mild steel matching colour fancy type brackets, stops of suitable size and necessary rings, side caps etc complete all as specified and directed.

Taking down unservicable 100/110mm dia AC/PVC/CI pipes with all fittings and S&F new 110mm dia PVC (SWR) pipes single socketed, fixed to wall or laid in flooring in any length with rubber ring joints complete all as specified and directed.

Taking down unservicable 75mm dia AC/PVC/CI pipes with all fittings and S&F new 75mm dia PVC (SWR) pipes single socketed, fixed to wall or laid in flooring in any length with rubber ring joints complete all as specified and directed.

S&F in repairs, 110mm dia PVC (SWR) bends / elbow / tee / socket complete all as spd. And directed

S&F in repairs, 75mm dia PVC (SWR) bends / elbow / tee / socket complete all as spd. And directed

S&F in repairs, 100mm dia CI floor trap with CP grating including jointing to waste pipe complete all as directed.

M&L for complete removal of existing decorative treatment of any description of walls including washing, rubbing down and stopping and applying two coats of weather proof paint over one of primer complete all as specified and directed.

M&L for preparing newly plastered surfaces of wall and applying two coats of weather proof paint over one coat of primer complete all as specified and directed.

M&L for complete removal of existing decorative treatment of any description of walls including washing, rubbing down and stopping and applying two coats of oil bound distemper over one of primer complete all as specified and directed.

M&L for preparing newly plastered surfaces of walls and applying two coats of oil bound distemper over and including 1mm thick layer of wall care putty of apprved make complete all as specified and directed

M&L for preparation of newly plastered surfaces of ceiling and applying two coats of white wash complete all as specified and directed.

M&L for preparing newly plastered surface of walls and applying two coats cement base paint over one coat of alkali resistant priming paint complete complete all as specified and directed.

M&L for complete removal of existing decorative treatment of any description of walls including washing, rubbing down and applying two coats of cement base paint complete all as specified and directed.

M&L for complete removal of existing decorative treatment of any description of walls including washing, rubbing down and stopping and applying 1.5mm thick layer of wall care putty of approved make and two coats of oil bound distemper (White or tinted) complete all as specified and directed.

M&L for complete removal of existing decorative treatment of any description of ceiling including washing, rubbing down and applying two coats of white wash complete all as specified and directed.

M&L for roof treatment with polymeric membrance (APP based) with non woven polyster mat as reinforcement including removing of existing roof treatment with following:- (a) M&L for preparation of surface by removal of existing treatment of tarfelt and taking down plaster to ensure or clean smooth and dry surface. (b) Providing and laying a coat of cold applied bitumen 85/25 based primer on entire surface @ 0.30 Itr/sqm on dry and clean surface. (c) M&L for providing and laying APP based polymeric membrance of 3 mm thinkness of weight of 150 gm / sqm with non woven polyster mat as reinforcement on primed surface by torch application with side laps & joints over laps etc as per manufacturer instruction. (d) M&L for applying a coat of blown bitumen grade 85/25 @ 1.20 Kg/Sqm on top of APP memberane and finally finishing the top surface by applying a coat of aluminium paint as per manufacturer's instructions. Note:- (i) All the water proofing treatment works shall be got carried out through authorised applicator of the firm. In this regard prior written approval from GE shall be obtained

M&L for PCC (1:4:8) type D2 (using 40mm graded stone aggregate) as in foundation, fiiling, sub base of floor and mass concrete complete all as specified and directed.

M&L for 15mm thick plastering on flat concrete surfaces of roof slab in cement mortar (1:4) mixed with liquid water proofing compound as per manufacturer's instructions complete all as specified and directed. Note:- WPC shall be measured and paid for separately at supply only rates.

M&L for rendering 20 mm thick cement plaster in cement mortar (1:3) using waterproofing compound on fair faces of concrete surfaces of sunken slab and the like finished even and smooth w/o using extra cement and complete all as specified and directed. Note: WPC shall be measured and paid for separately at supply only rate..

Supply only liquid water proofing compound of approved quality complete all as specified and directed.

M&L for carryingout water proofing treatment to sunken slab with Epoxy coating as specified below:- (a) Cleaning the surface free from dust, loose material etc (b) Providing & fixing 12mm dia GI Nozzle @1.50 m c/c on the entire area of the sunken portion. Grouting / injecting chemical through the nozzles with cement slurry admixture with DURA EV (Non shrink Polymeric grouting compound) with 40 PSI Pressure pump. Sealing off the nozzles and cutting the protruding portion of nozzles after the grout has set prperly. (c) Making angular fillets or 'Gola' with cement mortar (1:3) admixed with diluted DURAKRIT (1 Durakrit: 3 Water) at the junctions of the wall and slab etc. (d) Wetting the entire surface with water to make it SSD condition. (e) Applying one coat of DURAKRIT- Acrylic Polymer Modified Cementatious (PMC) slurry coating as per manufacturer's specifications (1:2) (1 DURAKRIT : 2 cement) by weight on the sunken floor surface turned upto 100mm from FFL and finished. (f) Applying second coat of DURAKRIT - Acrylic Polymer Modified Cementatious slurry coating as per manufacturer's specifications (1:2) (1 DURAKRIT:2 cement) by weight over the first coat at right angles. The second coat is usually applied after first coat of slurry has been touch dried, usually after 4 hrs. (g) Ponding test for water leakage shall be carried out as per IS:3370 Part 1 for seven days as instructed. Note: (i) The treatment shall be carrieout by the authorised applicator of the manufacturer in close supervision of the Engineer-in-Charge. (ii) Guarantee money / security deposit to be retained as per terms & condtions of the contract.

M&L for applying a coat of bitumen 85/25 @ 1.20 Kg per Sqm for receiving APP Membrane for bituminous water proofing treatment complete all as specified and directed by Engr-in-Charge.

M&L for laying APP membrane of 3.0 Kg Per Sqm including overlapping and sealing by torch application complete all as specified and directed.

M&L for 18 to 19 mm thick particle board medium density flat pressed single layer type or three layer type with BWR type adhesive fixed with screws to timber frame work complete all as specified and directed.

S&F 125mm long aluminium anodised hasp and staple including bolt to hinge plate and fixed with screws complete all as specified and directed.

S&F 2nd class hard wood in clean sawn scantlings 40cm and above in cross section and fixed in any position complete all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) including all fitiings and fixtures such as switches, sockets, ceiling rose, pendants, regulators etc and removing materials to store for keeping in safe custody or for taking credit (Credit for above items should be as per conditions separately) and making good disturbed surfaces of walls, floors etc to match the existing surfaces complete all as specified and directed.

Taking down ceiling fan along with complete accessoreis and removing blades from its existing place and deposited to MES Fan Store of AGE E/M Roorkee complete all as directed by Engineer-in-Charge.

M&L for concealed point wiring with 1.5 Sqmm (Nominal area) PVC insulated and PVC unsheathed FRLS multi stranded copper conductor single core cable drawn through and including PVC non metallic conduit of 20 mm dia (ISI marked) with all accessories including sunk type mild steel terminal boxes made of 1.6mm thick galvanised mild steel sheet with 3 mm thick bakelite sheet top cover (ISI marked) with and including 1. Sqmm size PVC insulated and unsheathed single core multistranded copper conductor cable green in colour as earth continuity conductor, connected to common earth and earth dolly, cutting chases for concealed wirin and making good surfaces in cement mortar (1:3) including white wash or any type distemper to match the existing decorative treatment and colour of building complete all as specified and directed for the following :-

One light point controlled by one, one way switch

One fan point controlled by one, one way switch

One 3/5 pin socket outlet 5 Amps on the same board with other switches.

One 3/5 pin 5 Amps socket outlet on independent board.

One bell/buzzer point controlled by one bell push button.

One light point controlled by two, two way switches

All as per Srl Item No. 104.00 here-in-before but point wiring for 15 Amps 3/5 pin power socket with 2.5 Sqmm (nominal area) (FRLS) copper conductor including 2.5 Sqmm copper conductor green colour for earth continuity complete all as specified and directed.

S&F switch piano flush type polycarbonate single pole one way 5 Amps complete all as specified and directed.

S&F switch piano flush type polycarbonate single pole one way 15 Amps complete all as specified and directed .

S&F socket outlet polycarbonate 2 in 1, 3 pin 5 Amps flush type complete all as specified and directed.

S&F socket outlet polycarbonate 2 in 1, 3 pin 5/15 Amps flush type complete all as specified and directed.

S&F switch piano flush type polycarbonate single pole two way 5 Amps complete all as specified and directed.

S&F bell push, flush type polycarbonate single pole 5 Amps complete all as specified and directed.

S&F in replacement electric bell ding dong type single phase AC 230 Volts, 50 Hz complete all as specified and directed.

S&F ceiling rose in polycarbonate 3 terminal brass flush type 6 Amps, 250 Volts AC (ISI marked), fixing on and including 3 mm thick 75mm dia sunmica hylum plastic laminated round sheet complete all as specified and directed. Make: Havells (ROHS) Cat Part No. AHLHXCW000 or Anchor PC Cat Part No. 3907250916 or SSK Cat Part No. B07QS98JCQ

S&F angle holder, PVC/Polycarbonate type with and including 3 mm thick 75mm dia sunmica hylum plastic laminated round sheet back plate suitable for batten fittings, complete all as specified and directed. Make: Havells (ROHS) Cat Part No. AHLHXAW000 or equivalent in Anchor / Anchor PC Cat Part No. 3980051170 or SSK Cat Part No. 76

S&F electronic fan regulator 230 Volts , step type (5 steps) socket type, hum free 100/300 watt complete all as specified and directed.

S&F in repalcement, 12 Watt LED Lamp, B22 type, having 1200 lumen intensity, complete all as specified and directed.

S&F in replacement, 14/15 Watt LED bulb as per standard specification, suitbale for batten / angular holder complete all as spacified and directed .

Taking down old unserviceable sub main wiring of any description and S&F new sub main wiring with two runs of 4.0 Sqmm 1100 Volt grade single core PVC insulated and unsheathed (FRLS) LT cable having multi stranded copper conductor, drawn through and including PVC non metallic conduit of 20mm / appropriate dia with all accessories and one run of 4.0 Sqmm 1100 Volt grade single core PVC insulated and unsheathed (FRLS) LT cable having multi stranded copper conductor complete all as specified and directed by Engineer-in-Charge. Note:- (i) Two runs of cable, one run of earth wire and one run of PVC non metallic conduit shall be measured as one run length. (ii) Cable required for connection to DBs and MCBs shall be deemed included in quoted rates. (iii) Earth wire shall run inside the conduit pipe.

All as per srl item No. 124.00 here in before but submain wiring with two runs of 6.00 Sqmm FRLS copper conductor and one run of 6.0 Sqmm FRLS earth continuity conductor complete all as specified.

Taking down old unserviceable light fittings of any description and S&F new LED tube light fitting 1x20 Watt, box type industrial batten type with bipin holders connector block complete with all accessories, internally prewired including 01 No. 20 watt retrofit LED tube rod T8 polycabonate type and connecting up with and including three core single wire of suitable size, complete all as specified and directed . Make : Havells (Rod) Cat Part No. PHOTONULTRAE 2.01213T8SSTL20WLED865SPC Havells (Batten) Cat Part No. REGALBATTENT 8UPTO1X22WSSBSWH or Bajaj (Batten) Cat Part No. 112181 BLRB-DB 118, Bajaj (Rod) Cat Part No. 112481 BLRB 21W CWC or Crompton Batten Cat Part No. DMLN1LT8-16 + Rod Cat Part No. LT8-20-865-2.

Taking down old unserviceable light fitting of any description and S&F new LED bulk head light fitting, aluminium housing with milky diffuser of capacity 12 watt complete all as specified and directed.

Taking down old unserviceable DB of any description and S&F new Distribution Board (DB) made out of sheet metal enclosure (CRCA sheet) dust and vermin proof SPN 8 way IP 43 (double door) with 200 Amps rated copper bus bar neutral bar, earth bar, single pole and neutral 250 Volts, flush to wall complete all as specified and directed. MAKE-L&T Hagar Cat No. Y81082 or INDOASIAN Cat No. 811807 or LEGRAND Cat No. 507611

Taking down old unserviceable DB of any description and S&F new Distribution Board (DB) made out of sheet metal enclosure (CRCA sheet) dust and vermin proof SPN 12 way IP 43 (double door) with 200 Amps rated copper bus bar neutral bar, earth bar, single pole and neutral 250 Volts, flush to wall complete all as specified and directed. MAKE- L&T Hagar Cat No. Y81122 or INDOASIAN Cat No. 811808 or LEGRAND Cat No. 5076 12

Taking down old unserviceable DB of any description and S&F new Distribution Board (DB) made out of sheet metal enclosure (CRCA sheet) dust and vermin proof TPN 4 way IP 43 (double door) with 200 Amps rated copper bus bar neutral bar, earth bar, single pole and neutral 200 Volts, flush to wall complete all as specified and directed. MAKE- L&T Cat No. DBTPE004DD or INDOASIAN Cat No. 811841 or LEGRAND Cat No. 5078 85

Taking down old unserviceable MCBs of any description and S&F new MCB single pole 6 to 32 Amps 240 Volt 'C' curve 10 kA, IP 20 transparent lebel holder fully insulated safety shutters suitable for cable up to 35 Sqmm cross sectional area including copper Lugs of suitable size complete all as specified and directed.

Taking down old unserviceable MCBs of any descriptio and S&F new MCB DP 40 Amps 240 Volt 'C' curve 10 kA, IP 20 transparent lebel holder fully insulated safety shutters suitable for cable up to 35 Sqmm cross sectional area complete including copper Lugs of suitable size complete all as specified and directed.

Taking down old unserviceable MCBs of any descriptio and S&F new MCB SPN 40-63 Amps 240 Volts, 'C' curve 10 kA, IP 20 transparent lebel holder fully insulated safety shutters suitable for cable up to 35 Sqmm cross sectional area complete including copper Lugs of suitable size complete all as specified and directed.

Taking down old unserviceable MCBs of any descriptio and S&F new MCB FP 40-100 Amps, 415 Volts, 'C' curve 10 kA, IP 20 transparent lebel holder fully insulated safety shutters suitable for cable up to 35 Sqmm cross sectional area complete including copper Lugs of suitable size and connection, testing and commissioning complete all as specified and directed. Make: INDOASIAN Cat No. 811242, LEGRAND Cat No. 4087 02, L&T Cat No. BB40630C

S&F Single pole and neutral enclosure with two pin earth plug and socket complete with one single pole MCB 20 Amps, complete all as specified and directed. Make: Legrand Cat Part No. 5078 11 20A SP 2P+E or IndoAsian Cat No. 810386 or L&T Hagar Cat No. Y84120

Taking down care fully any type and sweep of fans and kept in the safe custody and refixing the same after servicing and including cost of painting of two coats and MES numbering of existing shade by spray painting including filling cavities with filler complete all as specified and directed by Engr-in-Charge.

Repair to ceiling fan along with complete accessoreis including fixing of minor spares like nuts, bolts, cotter pin, rubber bush bearing except rewinding complete all as directed by Engineer-in-Charge.

Taking down/up old unserviceable cable and S&F new 16 Sqmm 2 core cross sectional area XLPE insulated armoured heavy duty electric cable with stranded aluminum conductor 1100 Volt grade and fixed to wall / ceiling or laid in floor / trenches etc all as specified and directed.

Excavation in trenches n.exc 1.5 m wide and n.exc 1.5 m in depth for laying cable and getting out in soft / loose soil complete all as specified and directed by Engineer-in-Charge.

Returning, filling in trenches including spreading, leveling, watering and well ramming in layers n.exc 25 cm thick in soft / loose soil after laying and testing of cable complete all as specified and directed.

Removing excavated soil to a distance n.exc 50 m and depositing where directed at a level not more than 1.5 m above the starting point complete all as specified and directed

M&L for dry sand cushioning to underground cables with 8cm thick before laying of cables and 15cm thick after laying and stretching of cable all as specified and directed by Engr-in-Charge. Note:- Punning thickness of sand cushioning shall be measured as 18 cm

M&L for laying bricks in protection covers cables using sub class 'B' old size bricks complete all as specified and directed

Taking down old unserviceable 40mm dia GI tubing of any graded and S&F new 40mm dia bore GI tubing, light grade with all fittings for cable protection including GI clamps, nut & bolts and washer or burried in ground etc complete all as specified and directed.

Taking down old unserviceable light fittings of any description and S&F building security light 35 Watt, IP66 LED street-light with aluminium pressure die-cast housing including brackets made out of 40mm dia GI pipe light grade, bent to shape including 02 Nos flat iron clamps, nut & bolts and connection complete all as specified and directed.

Taking down old unserviceable exhaust fan of any description and S&F new Exhaust fan of 300 mm sweep with louvers, metal body, 230 Volts, single phase including making connection, cutting holes of suitable size for exhaust fan in any type of wall and making good to match the existing surrounded wall complete all as directed by Engineer-in-Charge. Note: Old exhaust fan of any description shall be deposited in MES Fan Sotre of AGE E/M Roorkee

S&F PVC Ventilation (Exhaust) fan 250 mm sweep with louvers, AC 230 Volts, single phase including making connection cutting holes of suitable size for exhaust fan in any type of wall and making good to match the existing surrounded wall complete all as directed by Engineer-in-Charge.

S&F electric storage water heater of 25 Litre capacity BEE 5 Star rated including necessary grouting screws, non return valve and PVC connections for hot water and cold water complete all as specified and directed.

Dismantling house service brackets, any type complete all as specified and as directed

Taking down/up old unserviceable cable and S&F new 16 Sqmm 4 core cross sectional area XLPE insulated armoured heavy duty electric cable with stranded aluminum conductor 1100 Volt grade and fixed to wall / ceiling or laid in floor / trenches etc all as specified and directed.

Taking down old unserviceable 40mm dia GI tubing of any graded and S&F new 50mm dia bore GI tubing, light grade with all fittings for cable protection including GI clamps, nut & bolts and washer or burried in ground etc complete all as specified and directed.

M&L for hot water Tubes galvanized, duly insulated with glass wool aluminium cladding, "Medium grade " 15 mm bore supplied and laid or fixed to walls/floors complete including all fittings such as flanges, union ,reducers, sockets,reducing,bent, elbow, tee, checknut, caps etc, laid in trenches , complete all as specified and directed.

M&L for hot water Tubes galvanized, duly insulated with glass wool aluminium cladding, "Medium grade " 20 mm bore supplied and laid or fixed to walls/floors complete including all fittings such as flanges, union ,reducers, sockets,reducing,bent, elbow, tee, checknut, caps etc, laid in trenches , complete all as specified and directed.

Supply and fix CP brass stop valve , screwed,suitable for 15 mm dia pipe for hot water supply complete all as specified and directed.

Supply and fix CP brass stop valve , screwed,suitable for 20 mm dia pipe for hot water supply complete all as specified and directed.

S&F new 500 ltrs Rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position including 20mm ball valve high pressure of PTMT with epoxy coated aluminium rod & high desity plastic ball (minium weight 20mm-210gms) and 20mm dia bore GI hexa nipple etc complete all as specified and directed.

M&L for Framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc.complete all as specified and as directed.

M&L for solar water heating panel of capacity 200 LPD with all accessories (1 panel required for each 100 LPD capacity), complete all as specified and directed.

M&L for 3KW solar water heating element with all fitting accessories , complete all as specified and directed.

Descaling of solar water heating system of 700 LPD capacity, including replacement unserviceable minor elements complete all as specified and directed.

Dismantling existing unseviceable earthing of any description and M&L for new earthing complete with galvanized steel plate electrode 600 mm x 600 mm x 6 mm thick, burried directly in ground vertically in pit of depth not less than 2.25 metre below normal ground level with top edge of the earth plate at a depth not less than 1.5 metre below normal ground level surrounded from all sides with mixture of charcoal and common salt in alternate layers and electrode connected to GI earthing wire 4mm dia size by means of GI bolts, nuts, check nuts and washers, earthing wire protected by GI pipe 20 mm bore (light grade) connected to main switch board or any other electrical equipment all as shown in electrical plate No. 3 of SSR-2009 Part I and including necessary excavation and earth work in any type of soil, 20 mm bore medium grade GI pipe for watering, funnel with wire mesh, PCC (1:3:6) type C1 in chamber of size not less than 300x300x300mm (internal diamentions) with cover made of RCC (1:2:4), type B-1, reinforced with 8 mm dia TMT bars @ 15 cm C/C both ways and angle iron 40X40X5mm frame etc duly painted with two coats of synthetic enamel paint over a coat of red oxided primer on exposed surfaces complete all as specified and directed by Engineer-in-Charge. Note: The unit rate includes earthing wire and protection pipe upto maximum 7.5 metre from earth plate, earth point / test point.

G.H. INFRASTRUCTURE PRIVATE LIMITED

RAM PRAKASH AND ASSOCIATES

M/s MAA SHAKTI CONSTRUCTIONS AND SUPPLIERS