Loading
Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹21.9 LAccepted-AOC | L1 | Accepted-AOC L1 | |
| 2 | L2₹21.9 L+₹9,575.16 (0.44%)Rejected-AOC | L2 | Rejected-AOC L2 | |
| 3 | L3₹22.1 L+₹24,339.07 (1.11%)Rejected-Finance | L3 | Rejected-Finance L3 | |
| 4 | L4₹22.2 L+₹31,602.31 (1.45%)Rejected-Finance | L4 | Rejected-Finance L4 | |
| 5 | L5₹22.2 L+₹36,210.83 (1.66%)Rejected-Finance | L5 | Rejected-Finance L5 |
Tender Value
₹29.7 L
EMD Value
₹50,000
Closing Date
27 Jun 2023, 3:00 pmClosed
Executive Engineer
PWD Building Division Thrissur
DEPOSIT Providing Truss work over Superintendent office at Medical College Chest Hospital MG Kavu Thrissur work General Civil Work
2023_PWD_581370_1
14/2023-24/EE
Open Tender
Civil Works - Buildings
Item Rate
180 days
mulamkunnathukavu
Please refer Tender documents.
10 documents required · 10 mandatory
₹2,760
Yes
₹50,000
Yes
9 Aug 2023
13 Jun 2023
30 Jun 2023
13 Jun 2023
27 Jun 2023
13 Jun 2023
Amount
Truss work
4.3.1:Centering and shuttering including strutting, propping etc. and removal of form work for:Foundations, footings, bases for columns
50.4.1.1:Providing and laying in position cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size) up to floor five level excluding the cost of centering, shuttering, finishing for leveling coarse of floor and roof etc.
50.10.1:Steel work in built up G I tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete
50.10.2:Steel work for purlin/single section with G I pipes including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete
12.50:Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.
12.4.2:Providing ridges or hips width 60 cm overall width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete.0.63 mm thick with zinc coating not less than 275 gm/m2
13.61.1:Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work
OD3281/2022-2023:Supplying and fixing 160mm dia.PVC water gutter to fixing the end of slopped roof with MS clamps as per the direction of departmental officers at site
ANISH MATHEW
V M AZEEZ
P.O.ANTONY
MOHAMMED MUTHU IBRAHIM
Binu MG
Praveen Varghese
Mujeeb O M
K R PAULSON
dins joy
SHAJAN KP
VELAYUDHAN N R
Bidder Name
ANISH MATHEW
Binu MG
SHAJAN KP
K R PAULSON
V M AZEEZ
P.O.ANTONY
Praveen Varghese
Mujeeb O M
dins joy
VELAYUDHAN N R
IJAS C
MOHAMMED MUTHU IBRAHIM
stage.html
html • 0.07 MB
tech_eval.pdf
fin_eval.pdf
aoc.pdf
boq_comp_chart.xlsx
xlsx
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .