SPECIAL REPAIR TO ROOFING AND EXTERNAL FINISHES TO BUILDING NO. P-1 (GOI) AND PROVISION OF CERTAIN MINOR/REVENUE WORKS AT MILITARY STATION KOTA

Amount

Demolition/Dismantling of existing normal roof treatment, any type from RCC roof slab including wire brushing and cleaning of foreign materials, loose dirt etc, complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and and in any position not otherwise specifically provided for and removing rubbish from premises, complete all as specified and directed.

Taking down cement plaster of any description and thickness on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed.

M&L brushing neat cement slurry with 3.00 kg cement per Sqm, complete all as specified and directed.

Supply only approved liquid water proofing compound, complete all as specified and directed.

M&L for PCC 1:2:4 mix type B-0 (Using 12.5 mm graded stone agg) for roof padding, leveling course to receive floor finishes etc and finishing the surfaces fair and even, complete all as specified and directed.

M&L for cleaning of roof slab including picking, sweeping clean and washing down with water to remove dust, dirt etc and Supply and fix APP polymeric water proofing membrane, minimum 3mm thick and weighing not less than 3.0 Kg/Sqm, black finish, reinforced with non-woven polyester mat with a thermo fusable finish, laid over compatible bitumen primer @ 0.40 Kg/Sqm, torching overlaps with propane or butane gas torch, with an overlap of 75mm at the sides and 100mm at the ends and sealing, complete all as per manufacturer’s instructions, specified and directed. Note: (i) Coved fillets in PCC(1:2:4) type B-0 using 12.5mm graded stone aggregate, of radius 75mm shall be provided at the junction of roof and parapet wall/mumty/chimney/other vertical surfaces and thereafter surface painted with hot paving bitumen of Grade 30/40 confirming to IS-73, [email protected] Kg/Sqm over a coat of bituminous primer confirming to IS-3384 applied @ 0.40 Kg/Sqm.

Item 7.00 Contd……. (ii) Polymeric membrane shall be taken to a height of 45cm (minimum) and then inserted inside the groove of parapet wall of brick masonry and shall be finished by a membrane flushing. (iii) The waterproofing treatment shall be got carried out by the manufacturer or their authorized applicators. (iv) In case of stone masonry parapet wall etc a groove of size 25mmx25mm(minimuim) shall be made in coved fillet at the junction of roof and parapet wall/mumty Chimney/other vertical surfaces and polymeric membrane shall be inserted in groove and sealed with paving bitumen. (v) Cost of these factors shall be deemed included in the unit rates.

Excavation in trenches not exc 1.5 m wide and not exc 1.5 m deep for foundation etc or for shafts, column footings or for laying pipes/cables etc not exc 10 Sqm on plan and getting out in soft/loose soil, complete all as specified and directed.

Excavation over areas not exc 1.5 m deep and getting out in soft/loose soil, complete all as specified and directed.

Excavation over areas exc 1.5 m but not exc 3.0 m deep and getting out in soft/loose soil, complete all as specified and directed.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil, complete all as specified and directed.

Surface dressing not exceeding 15 Cm deep in soft/loose soil, complete all as specified and directed.

Returning filling in soil including spreading, leveling, watering and well ramming in layers not exc 25 Cm, complete all as specified and directed.

Removing excavated materials (soil) not exc 50 m distance and depositing where directed at a level not exc 1.5 m above starting point complete all as specified and directed.

M&L hardcore (broken stone) of gauge not exc 63 mm, deposited spread and leveled in layers not exc 15 cm thick, watered and rammed to a true surface, complete all as specified and directed.

M&L mooram or red bajri filling in floors or pavings, hardstanding and in foundation etc, laid in layers not exc 15 cm thick, spread, leveled and rammed including watering, complete all as specified and directed.

M&L loose filling with broken bricks bats in soakage wells etc and the like, complete all as specified and directed.

M&L for PCC 1:3:6 mix type C-1 (Using 20mm graded stone agg) as in bed blocks for fixing hold fasts, bolts etc, complete all as specified and directed.

M&L PCC 1:4:8 type D-2, using 40 mm graded stone aggregate, as in foundation, filling, mass concreting etc, complete all as specified and directed.

M&L for cement concrete 1:4:8 type D-2 (using 40 mm graded stone aggregate) 75 mm thick as in sub base, finishing the surface even & rough to receive topping layer, complete all as specified and directed.

M&L for cement concrete 1:4:8 type D-2 (using 40 mm graded stone aggregate) 100 mm thick as in sub base, finishing the surface even & rough to receive topping layer, complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 (using 40mm graded stone aggregate), 75 mm thick as in plinth protection/Path/PCC paving etc including finishing the surface even & smooth without using extra cement, with and including all necessary formwork to divide the area in panels, finishing exposed edges fair or rounding or chamfering where directed and providing 6 mm wide joints throughout the thickness of plinth protection duly filled with mastic filling (one part of hot bitumen 85/25 and three parts of fine sand by weight), complete all as specified & directed.

M&L for RCC 1:1.5:3 type A-1 (using 20 mm graded stone aggregate) as in slabs supported on walls, beams and columns, in floors, roofs, landing balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed.

M&L for RCC 1:1.5:3 type A-1 (using 20 mm graded stone aggregate) as in beams, cantilevers, bressumers, lintels etc, complete all as specified and directed.

M&L for RCC 1:1.5:3 type A-1 (using 20 mm graded stone aggregate) as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns etc, under-reamed piles and mass concrete, complete all as specified and directed.

M&L for RCC 1:1.5:3 type A-1 (using 20 mm graded crushed stone aggregate), as in columns, pillars, piers, posts and struts etc, complete all as specified and directed.

M&L providing cast in situ cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed.

M&L PCC 1:3:6 type C-2 using 40 mm graded stone aggregate as in surface channel and drains, complete all as specified and directed.

a) Extra for forming fair finished drain or channel 30 cm inner girths in cement concrete using extra cement incl forms, moulds, mitered/stopped ends etc, complete all as specified and directed.

b) Add to or deduct therefrom for each additional 25 mm girth or part thereof.

M&L for 25mm thick plain cement concrete 1:2:4 type B-0 (using 12.50 mm graded stone aggregate) as in flooring/sub base finished rough to receive floor finishes/screed, complete all as specified and directed.

M&L brick work with pulverized fuel Ash-lime bricks (Fly ash bricks - non modular size), straight or curved on plan exc 6 m mean radius, built in CM 1:6, complete all as specified and directed.

M&L for brick work with pulverised fuel Ash-lime bricks (Fly ash bricks - non modular size), straight or curved on plan to any radius in half brick walls built in cement mortar 1:4, complete all as specified and directed.

M&L brick work with old size sub class 'B' bricks, straight or curved on plan exc 6 m mean radius, built in CM 1:4, complete all as specified and directed.

M&L for brickwork with old size sub class ‘B’ bricks in one brick thick honey comb walling, built in CM 1:4, complete all as specified and directed.

M&L walling of random rubble, uncoursed well bonded, bedded and solidly hearted, built in Cement Mortar 1:6, complete all as specified and directed.

Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints, as specified, of random rubble walling, uncoursed or brought upto courses, with maximum depression on face from straight edge held against the dressed surface not exceeding 40 mm; to block in course masonry (Lime or sand stone), complete all as specified and directed.

Formwork (rough finished surfaces) to soffits of suspended slabs such as roof slabs, floor slabs, landing and similar works, not exc 200 mm thick complete all as specified and directed.

Formwork (rough finished surfaces) to sides of concrete foundations, column footings, bases of columns, raft and raft beams, sides and soffits of plinth beams or other similar works, vertical or to batter for rough finished surfaces complete all as specified and directed.

Formwork (rough finished surfaces) to sides of columns, pillars, piers, posts, struts and stanchions etc, complete all as specified and directed.

Formwork (for fair finished surfaces) to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc., complete all as specified and directed.

Taking down Chowkats or frames with shutter (without taking off shutters from the frame) n. exc. 1.50 Sqm each complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement, complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplying & fixing in opening as per specification & drawing, complete all as specified and directed.

S&F aluminium anodised barrel tower bolt of extruded section 150 mm long and fixed, complete all as specified and directed.

S&F 250mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed, complete all as specified and directed.

S&F 100 mm size stainless steel butt hinges and fixed with stainless steel screws, complete all as specified and directed.

S&F extruded aluminium alloy handles, fabricated type, anodised 150 mm size, complete all as specified and directed.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips, complete all as specified and directed.

M&L for mild steel TMT bars 6 to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips, complete all as specified and directed.

~Ditto~ but 5 to 10 mm dia mild steel TMT bars as in stirrups, spacers and binders etc complete all as specified and directed.

S&F mild steel framed work as in grills, grating etc. with end of bars shouldered and/or riveted, or forged into spikes: framed guard bars: barred iron doors: ladders: frame balusters: walk ways: railing: frame work of water tanks and similar works conforming to Fe-290 Grade-E-165, complete all as specified and directed.

S&F for mild steel work as in bands, straps, hold fasts etc and similar small articles conforming to Fe-290 Gde-E-165, complete all as specified and directed.

M&L rolled mild steel door frames made of angle iron with and including hold fasts and FI thresh hold etc, and fixed to openings, conforming to Fe-290 Gde E-165, complete all as specified and directed.

M&L mild steel framed work as in doors or gates of angles or other section with gusset plates, rails braces etc complete drilled for fixing of steel sheeting or other covering doors etc to be prepared for hanging or sliding with including either hooks and hinges or steel hanging door fittings (excluding of steel sheeting or other covering running rails and guides) and hanging also fastening and fixing, conforming to Fe-290 Grade-E-165, complete all as specified and directed.

S&F 11 to 15 mm dia MS screw bolts (Machine made ) with hexagonal or square head at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washer and one hexagonal or square nut, length of bolt not exc 5 cm but n exc 15 cm long, complete all as specified and directed.

S&F welded steel wire fabric supplied and fixed complete to wood or steel members, weight per Sqm not exceeding 4.00 kg, complete all as specified and directed.

M&L precast RCC 1:2:4 type B-1 using 20 mm graded crushed stone aggregate as in manhole/drain cover slabs, landing slabs, shelves and similar articles with plain faces, set in CM 1:4, with and including necessary Formwork, complete all as specified and directed.

S&F steel windows/ventilators with top hung shutters including box type hinges with steel handle and steel peg stay, complete with glazing bars, dovetailed or welded including one shop coat of zinc chromate primer, complete all as specified and directed.

S&F steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, including one shop coat of zinc chromate primer, complete all as specified and directed.

M&L for joint free non skid ceramic coloured tiles, 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles, laid over and including 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L Glazed ceramic coloured tiles on vertical surfaces 350x 250x7 mm/450X350X7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match, laid over and including 10 mm thick rendering in CM 1:4, complete all as specified and directed.

M&L for laying anti skid fully vitrified paving tiles of size 300x300x15 mm thick suitable for exterior areas, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the colour of tiles, laid over and including 15 mm thick screed in CM 1:6, complete all as specified and directed.

M&L for 15 mm thick rendering on fair faces of RCC roof slab in CM 1:4 duly mixed with liquid water proofing compound as per manufacturer's instructions, finishing surfaces even and smooth without using extra shall be measured and pais separately.)

M&L for 15 mm thick rendering on fair faces of brick/concrete surfaces in CM 1:4 finishing surfaces fair and even, complete all as specified and directed.

M&L rendering 5 mm thick in CM 1:3 on concrete surfaces of ceiling, finished even and smooth without using extra cement, complete all as specified and directed.

M&L for 10 mm thick rendering on other than fair faces of brick work or stone masonry surfaces in CM 1:4 finishing surfaces even and smooth without using extra cement, complete all as specified and directed.

M&L for 15 mm thick rendering on fair faces of brick work or stone masonry surfaces in two layers, consisting of 10 mm thick in CM 1:6 and over that 5 mm thick in Cm 1:4 using liquid water proofing compound as per manufacturer's instruction's, finishing surfaces even and smooth without using extra cement, complete all as specified and directed. Note: Water proofing compound shall be measured and paid separately.

M&L for 15 mm thick rendering on fair faces of brick/concrete surfaces in CM 1:6 finishing surfaces even and smooth without using extra cement, complete all as specified and directed.

M&L for 15 mm thick rendering on fair faces of brick/concrete surfaces in CM 1:4 finishing surfaces even and smooth without using extra cement, complete all as specified and directed.

M&L for 10 mm thick rendering on fair faces of brick/concrete surfaces in CM 1:4, finishing surfaces even and smooth without using extra cement, complete all as specified and directed.

M&L for 15 mm thick rendering on other than fair faces of brick work or stone masonry surfaces in CM 1:6 finishing surfaces even and smooth without using extra cement, complete all as specified and directed.

M&L struck pointing in Cement Mortar 1:4 to squared or rectangular rubble, coursed or uncoursed masonry, including cleaning and washing with water to existing wall and curing complete and painting to pointing lines with two coats of exterior grade weather proof paint, complete all as specified and directed. (Note: Unit rates quoted by the contractor shall be deemed inclusive of cost of scaffolding etc as required at site.)

M&L for applying three coats of white wash on ceiling including preparation of new or previously untreated surfaces, complete all as specified and directed.

M&L for applying three coats of white wash on walls including preparation of new or previously untreated surfaces, complete all as specified and directed.

M&L for applying two coats of cement based paint over a coat of primer on newly plastered surfaces of walls including preparation of surfaces, complete all as specified and directed.

M&L preparation of newly plastered surfaces of walls and applying 1 to 1.5 mm thick wall care putty as per manufacturer's instructions and over it applying two coats of distemper oil emulsion over a coat of primer, complete all as specified and directed.

M&L for figured glass, 3 mm thick, pin head type and glazing with oil putty in squares not exc. 0.50 Sqm in each pane complete all as specified and directed.

M&L for preparing new steel surfaces exceeding 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer, complete all as specified and directed.

Disconnecting existing tank exc 250 ltrs and not exc 500 ltrs capacity, setting aside (or lowering if required) for repairs and cleaning etc and hoisting if required, reconnecting and refixing in position after repair of building, complete all as specified and directed.

Disconnecting existing tank exc 500 ltrs and not exc 1000 ltrs capacity, setting aside (or lowering if required) for repairs and cleaning etc and hoisting if required, reconnecting and refixing in position after repair of building, complete all as specified and directed.

Dismantling water storage tank of any description of capacity exc. 250 ltr but n.exc. 500 ltr, complete all as specified and directed.

Dismantling water storage tank of any description of capacity exc. 500 ltr but n.exc. 1000 ltr, complete all as specified and directed.

S&F 20 mm dia ball brass valve, high pressure with polythene float and fly nut, screwed down for iron pipe, complete all as specified and directed.

Taking up or down steel tubing 15 mm bore and connections including cleaning for refixing or removal to store, complete all as specified and directed.

Taking up or down steel tubing 20 mm bore and connections including cleaning for refixing or removal to store, complete all as specified and directed.

S&F 15 mm dia GI tubing, medium grade, with all fittings and fixed complete to walls, ceilings and floors, complete all as specified and directed.

S&F 20 mm dia GI tubing, medium grade, with all fittings and fixed complete to walls, ceilings and floors, complete all as specified and directed.

S&F stop valve 15 mm nominal bore cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipes or for unions and fixed, complete all as specified and directed.

S&F gun metal globe or gate valve of size 20 mm bore with iron wheel head screwed both ends and for iron pipe & fixed, complete all as specified and directed.

S&F 75 mm dia cast iron soil, waste & vent pipes, with or without ears, in any length, with cement joints, fixed to walls, complete all as specified and directed.

S&F 75 mm cast iron bends with oval access door, any radius with diminishing pieces or tapers (larger bore measured), complete all as specified and directed.

S&F 75 mm dia branch pieces, single (Equal/unequal) ordinary or inverted (spigot or socket type) or with parallel branches, complete all as specified and directed.

S&F CI cowl 75 mm bore fixed with cement joint, complete all as specified and directed.

S&F 75 mm dia cast iron floor trap, with CP grating including jointing to waste pipe and fixed in cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregate) complete all as specified and directed.

M&L Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc. and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting not exceeding 10 cm girth as in brick wall complete all as specified and directed.

Cutting existing steel tubing for alterations or additions and screwing the same for alterations or additions, 20 mm bore, complete all as specified and directed.

S&F bib taps, cast copper alloy, fancy type, chromium plated, with capstan head, screwed down, screwed for 15 mm bore GI pipe or for brass ferrule or to GI socket complete all as specified and directed.

S&F bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for 15 mm bore GI pipe or for brass ferrule or to GI socket, complete all as specified and directed.

S&F Angle valve, fancy type, chromium plated brass, screwed down, high pressure, screwed one end to iron pipe or union of dia 15 mm, complete all as specified and directed.

S&F pillar taps, cast copper alloy, with capston heads, chromium plated, screwed down high pressure with or without lettered 'Hot' or 'cold' with long screwed shanks and flynuts screwed for 15mm bore iron pipe and fixed, complete all as specified and directed.

S&F soap dish made of stainless steel, approx size 160x100 mmx 1 mm thick, fixed to walls with SS screws and PVC rawl plug, complete all as specified and directed.

S&F PVC connection, 15 mm size with two PTMT nuts, length of connection 450 mm, complete all as specified and directed.

S&F grating doom of 125 mm dia, made of stainless steel with or without waste hole, complete all as specified and directed.

S&F vitreous china squatting pan Orissa pattern size 580 x 440 mm white with front or back inlet, integral foot rest incl providing lime concrete bedding and connecting to flusing cistern, complete all as specified and directed.

S&F 10 Ltr vitreous china valveless syphonic action type flushing cistern, low level, coloured with inlet, ball valve, float and handle incl PVC flush pipe of 32 mm dia, fixed to wall, complete all as specified and directed.

S&F vitreous china wash hand basin white with flat back of size 550x400 mm, excluding chain and plug, taps and porcelain stopper but incl PVC waste pipe of 32 mm bore, one pair of 600 mm long cast iron brackets, complete all as specified and directed.

M&L cutting existing manholes for connecting new drain (for 150 mm bore pipe), making good to pipe and rendering, cutting out existing benching for forming branch channel (half round or 3/4 section) in cement concrete 1:2:4 type B-1 or smooth finishing, complete all as specified and directed.

M&L for 150 mm dia salt glazed stoneware drain pipes, laid in trenches and jointed in cement sand slurry in 1:2, complete all as specified and directed.

M&L PCC 1:4:8, type D-2 using 40 mm graded stone aggregate, as in concrete bed to drain pipes including packing under and haunching against the sides of 150 mm dia pipe, after they are laid and tested, complete all as specified and directed.

S&F vitreous china half stall type urinal, white with grating and union for discharge pipe, including providing and fixing plugs, bedding urinal against wall in CM 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back with white cement, complete all as specified and directed.

S&F 32mm dia waste coupling of PTMT (half or full threaded) minimum weight not less than 45 grams, complete all as specified and directed.

S&F urinal spreader of PTMT (Minimum weight 60 Gms), any colour for fixing with 20 mm dia pipe, complete all as specified and directed.

S&F vitreous china urinal partition, white, size 310x700 mm, fixed to wall and pointing around edges in white cement, complete all as specified and directed.

S&F white vitreous china wash down water closet pan (pedestal pattern) white including plastic seat cover white with flat bottom and mild steel chromium plated or aluminised hinging device, complete all as specified and directed.

S&F vitreous china wash hand basin coloured with flat back of size 560x430 mm provided with pedestal as per the sample approved by GE, excluding taps but including chain and plug, porcelain stopper, PVC waste pipe of 32 mm bore, one pair of 600 mm long cast iron brackets and CP waste coupling of 32 mm bore, complete all as specified and directed.

S&F 15 mm bore CP brass centre hole basin mixer for mixing hot and cold water, screwed down for iron pipe and fixed, complete all as specified and directed.

S&F toilet jet spray made of stainless steel with minimum 1 m long PVC pipe and CP brass connector suitable for 15 mm bore stop cock, including all accessories, fixed to EWC, complete all as specified and directed.

S&F stainless steel toilet paper holder, fixed on wall with SS screws including PVC washer and PVC rawl plug, complete all as specified and directed.

SEF glass shelf of 5 mm thick glass and CP guards of approved quality and fixed to wall with SS screws including PVC rawl plug etc, complete all as specified and directed.

S&F salt glazed stone ware gully traps, square or round mouthed, type 'P', size 150x150 mm, with and including bedding in PCC 1:5:10 type E1 using 20 mm graded stone aggregate, complete all as specified and directed.

S&F shower rose, chromium plated brass, fancy type, 125 mm size with swivel joint, screwed to iron pipe or for union of 15 mm dia, complete all as specified and directed.

S&F 500 Ltrs capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position, complete all as specified and directed.

S&F 1000 Ltrs capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position, complete all as specified and directed.

S&F 20 mm dia ball brass valve, high pressure with polythene float and fly nut, screwed down for iron pipe, complete all as specified and directed.

S&F PVC (SWR) pipe 110 mm bore, single socketed, in any length with rubber ring joints and fixed to walls, complete all as specified and directed.

S&F PVC (SWR) bend 110 mm bore, any radius, incl jointing to waste pipe with solvent cement, complete all as required and as directed.

S&F PVC (SWR) bend 110 mm bore with oval access door, any radius, incl jointing to waste pipe with solvent cement, complete all as required and as directed.

S&F PVC (SWR) vent cowl 110 mm bore, incl jointing to waste pipe with solvent cement, complete all as specified and directed.

M&L Machine pressed precast concrete interlocking paver block any shape and size made with grey cement and pigment, confirming to IS 15658-2006 of 80 mm thickness, M-40 Grade, laid over and including 25 mm thick sand cushion, complete all as specified and directed.

M&L Machine pressed precast concrete interlocking paver block any shape and size made with grey cement and pigment, confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade, laid over and including 25 mm thick sand cushion, complete all as specified and directed.

M&L precast (factory casted) cement concrete kerb stone casted in PCC 1:2:4 type B-1 using 20 mm graded stone aggregate with plain or interlocking joints (as directed), making groove in ground of desired dimension, placing in position and set and jointed in CM 1:4, making good disturbed surface of ground, complete all as specified and directed.

S&F Prepainted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified, complete all as specified and directed.

M&L for cutting openings through walls for door, window and other openings or enlarging existing openings, etc., or cutting out defective masonry for underpinning including providing, fixing and removing, shoring, cleaning and stacking stone and removing surplus to store and rubbish off the premises, complete all as specified and directed.

Cutting holes into or through brick walls built in cement mortar exc. 150 Sqcm but not exc. 400 Sqcm and making good in CM 1:3 or cement concrete 1:2:4 type B-1(using 20 mm graded stone aggregate), complete all as specified and directed.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendents, regulators, sockets, light fittings etc removing materials to store for reuse or for taking credit and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

Dismantling unserviceable main switch/DBs incl wooden board and deposit to MES store yard including making good disturbed surface of wall complete all as specified and directed.

Taking down sub main wiring of any size/capacity complete all as specified and making good disturbed sufaces to match with the existing surface, complete all as specified and directed.

Disconnecting and taking down carefully ceiling fan/exhaust fan and refixing after cleaning, oiling/greasing and connecting with suitable size copper conductor cable, complete all as specified and directed.

M&L for Point wiring with PVC insulated (FRLS) unsheathed multi stranded copper conductor cable of size 1.5 Sqmm with PVC insulated (FRLS) unsheathed multi stranded copper conductor cable of size 1.5 Sqmm as earth continuity wire to be drawn in and including PVC casing capping not less than 20 mm width with all accessories and fittings, fixed on surface including making good disturbed surface all as specified and directed for the following: - One light/ceiling fan/exhaust fan/bell buzzer point controlled by one, one way switch of 5/6 Amps.

One 5 Pin, 5/6 amps socket outlet point on independent board, controlled by one, one way 5/6 Amp switch.

One 5 Pin, 5/6 amps socket outlet point on same board, controlled by one, one way 5/6 Amp switch.

One light point controlled by two, two way 5/6 Amp switches.

M&L Point wiring with PVC insulated (FRLS) unsheathed multi stranded copper conductor cable of size 2.5 Sqmm, with PVC insulated (FRLS) unsheathed multi stranded copper conductor cable FRLS of size 2.5 Sqmm as earth continuity wire to be drawn in and including PVC casing capping not less than 20 mm width with all accessories and fittings, fixed on surface for one socket outlet 15 amp on independent board including making good disturbed surface, complete all as directed and specified.

S&F switch piano flush type 5/6 Amps, 230 volts, single pole, one way, ISI marked, complete all as specified & directed.

S&F switch piano flush type 5/6 Amps, 230 volts, single pole, two way, ISI marked, complete all as specified & directed.

Supply and fixing switch socket combination, 5/6 and 15/16 Amps, 230 volt, multi pin, flush type universal, complete all as specified and directed.

Supply and fixing switch socket combination, 5/6 Amps, 230 volt, multi pin, flush type universal, complete all as specified and directed.

Supply and fixing socket outlet, 5/6 Amps, 230 volt, multi pin, flush type universal, complete all as specified and directed.

S&F stepped type electronic fan regulator, flush type, 230 volts AC, single pole, humming free, fixed on the existing phenolic laminated sheet, complete all as specified and directed.

S&F ceiling rose surface type PVC/Polycarbonate isolated body, 65x 20mm, 3 terminals, complete all as specified & directed.

S&F LED Tube light fittings, batten type with bipin holders, powder coated steel with retrofit 20 watt LED tube, internally prewired, complete all as specified and directed.

S&F PVC/polycarbonate lamp holder, angular/batten type with back plate, complete all as specified & directed.

S&F MCB, 6 to 32 Amps, Single Pole, 240 Volt, 10 KA 'B' curve including all accessories, complete all as specified and directed.

S&F MCB, 6 to 32 Amps, Single Pole & Neutral, 240 Volt, 10 KA 'B' curve including all accessories, complete all as specified and directed.

S&F MCB, 63 Amps, Triple Pole & Neutral, 415 Volt, 10 KA 'B' curve including all accessories, complete all as specified and directed.

M&L for MCB DB made of sheet steel phosphatised, powder painted with bus bar 200 A, neutral link, earth bar and Din rail, 415 Volts TPN with 4 ways, Double door, complete all as specified and directed.

M&L for MCB DB made of sheet steel phosphatised, powder painted with bus bar 200 A, neutral link, earth bar and Din rail, 240 Volts SPN with 8 ways, Double door, complete all as specified and directed. Note for item Nos 154 & 155 - (1) The unit rate includes for cutting the brick walls to accommodate DB to make it flush to wall. (2) The unit rate includes for making good the disturbed surfaces including finishes to match with the adjoining surface.

S&F of sub main wiring with two runs of single core PVC insulated and unsheathed FRLS multistranded copper conductor cable of size 6 Sqmm LT, 1100 volts grade, drawn through and including 25 mm dia PVC non metallic surface conduit with accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc. and fittings and one run of 6 sqmm single core multistranded FRLS copper conductor cable green colour as earth continuity conductor complete all as specified & as directed. NOTE:- (i) Two runs of cable one run of earth wire and one run of PVC non metallic conduit of 25mm dia shall be measured as one run length. Cable required for connection to DBs shall deemed to be included and shall not be measured separately. Earth wire shall run inside the PVC conduit. Cutting chases in walls shall not be measured and paid separately.

M&L for Earthing with galvanized steel earth plate electrode of size 600 mm x 600mm x 6.0 mm, buried directly in ground (earth plate not less than 2.25 Mtr below normal ground level) connected to galvanized earth wire of 4 dia mm by means of bolts, nuts, check nuts and washers of galvanized iron including 15 mm dia light grade GI tubing for protection of earth wire, MS sheet metal funnel with wire mesh, watering pipe medium grade 20 mm dia, charcoal or coke and common salt in alternative layer of 15 Cm compacted thickness all around the electrode with concrete earth pit of PCC 1:3:6 type 75 mm thick precast RCC (1:2:4) type B1 pit cover reinfored with 8 mm dia deformed bar and suitable handle made of 10 mm dia round bar and necessary excavation, earth work, in soft/loose soil and disposal of spolis to a distance not exc 50 Mtr and necessary connection and testing complete all as shown in electrical plate No. 3 and complete all as specified and directed. Notes: - (a) Irrespective of whatever is shown in plate No 5 of SSR, earth pit shall be casted in PCC (1:3:6) type C-1 and precast cover of RCC (1:2:4) type B-1 with suitable handle. (b) Item includes the cost of GI pipe for protection of earth wire/strip and earth strip upto 7.5 m. Any variation below or above shall be measured and paid for separately under relevant item of this Sch ‘A’.

S&F single pole & neutral enclosure, two pin and earth plug and socket complete with one double pole MCB 32 Amps, complete all as specified and directed.

S&F LED street light fitting, 25 watt, pressure die cast aluminium housing with IP 66 deg of protection, complete with 1.20 m long street light bracket made of 40 mm bore GI light grade tubing including necessary clamps, nuts, bolts, washers etc, complete all as specified and directed.

S&F PVC rectangular block for mounting switches, sockets, fan regulators etc with 3 mm thick plastic laminated sheet cover of size 100x100 mm and 50 mm deep, complete all as specified and directed.

S&F PVC rectangular block for mounting switches, sockets, fan regulators etc with 3 mm thick plastic laminated sheet cover of size 175x100 mm and 50 mm deep, complete all as specified and directed.

S&F PVC rectangular block for mounting switches, sockets, fan regulators etc with 3 mm thick plastic laminated sheet cover of size 200x150 mm and 50 mm deep, complete all as specified and directed.

S&F PVC rectangular block for mounting switches, sockets, fan regulators etc with 3 mm thick plastic laminated sheet cover of size 250x200 mm and 50 mm deep, complete all as specified and directed.

S&F LT 1100 volts grade UG cable XLPE insulated screened PVC bedded, galvanised steel strip or wire armoured electric power cable (heavy duty) with stranded aluminium conductor, 3.5 core 35 Sqmm, laid in trenches/ducts, fixed on wall/inside panel or drawn through pipe, complete all as specified and directed.

Supply, installing, commissioning and testing energy efficient BEE 5 star rated split type air conditioner with intelligent remote control, 220Volts AC, nominal capacity 1.5 TR, complete with copper condensing tubing designed for outside ambient temperature (summer 50 degree celcius, monsoon 32 degree celcius), relative humidity 50% to 60 %, number of air changes 3-4 per hour, copper refrigerant piping with insulation (EP foam pipe section) upto 3 metre from indoor unit to outdoor unit with copper power cables upto 4 mtr including supply, fixing/grouting a set of best quality mounting brackets for outdoor unit, complete all as specified and directed.

Supply, installing, testing and commissioning Voltage stablizer for automatic operation, single phase naturally air cooled, indoor type and designed for input voltage of 170-260 volts with out put voltage stablized at 220 volt with accuracy of +/-1.00%, capacity 5.0 KVA, mounted on wall with suitable arrangements, complete all as specified and directed.

SINGH ENTERPRISES

ANNAPURNA ENTERPRISES

SHREEKRISHNA INFRASTRUCTURE

Ganesh Contruction

L P Singh and Co.

M/s Prem Associates