EMPANELMENT OF CONTRACTOR FOR THE WORK OF ANGANWADI AT DIFFERENT PLACES IN EAST ZONE IN AHMEDABAD

I Bill of Quantity 3-6

AHMEDABAD MUNICIPAL CORPORATION

NAME OF WORK :- “EMPANELMENT OF CONTRACTOR FOR THE WORK OF ANGANWADI AT

DIFFERENT PLACES IN EAST ZONE IN AHMEDABAD”

Quantity Rate Rs. Per Amount Rs.

CIVIL WORKS_ PART-(A)

1 Excavation for foundation upto 1.5 m depth including sorting

out and stacking of useful materials and disposing off the 85.13 115.92 Cmt.

excavated stuff upto 50 Meter lead.(A) Loose or soft soil

2 Filling available excavated earth (excluding rock ) in

trenches.plinth,sides of foundations etc.in layers not

exceeding 20cm.in depth consolidating each disposited layer 68.10 129.10 Cmt.

by ramming and watering.

3 Conveyance charge of earth ,lime,murrum, building rubbish,

manual garbage,sludge,excavated rock ,fly ash, aggregate of 50.00 235.51 Cmt

any kind etc. comp. Up to 5.0 Km. lead.

4 Providing and laying cement concrete 1:5:10 (1-Cement:5-

Coarsesand:10- hand brokenstone aggregates 40mm no

minalsize)and curing complete excluding cost of formwork in 15.37 2492.51 Cmt.

(A) Foundation and Plinth

5 Provdg. & laying ordinary cement concrete 1:1.5:3 (1 cement :

1.5 coarse sand : 3graded stone aggregates 20 mm nominal

size) for R.C.C. linted including finishing smooth with curing 21.03 4610.00 Cmt.

etc.complete including the cost of form work but excluding the

cost of reinforcement.

5.2 Providing and laying controlled cement concrete of M-

25 Grade and curing complete, Excluding the cost of

form work, Scaffolding, cost of reinforcement for

reinforced concrete work For any Height up to any

5.2.1 Foundations,Raft,Footings,Mass concrete 1.00 4238.04 Cmt.

5.2.2 Tie-Beam, Lintel , Beam- Bracket, Stair Case &

Landing, Coping ,Slab, balcony, weather shed, loft , any 1.00 4496.07 Cmt.

cantilever etc All Floor

Columns,Pillars, posts and struts at All Floor 1.00 4593.91 Cmt.

6 Providing TMT Bar FE 500D reinforcement for R.C.C. work

including bending, binding and placing in position complete 2523.60 75.46 kg

upto floor two level

7 Brick work using common burnt clay building bricks having

crushing strength not less than 35 kg./Sq.Cm. in foundation

and plinth in Cement Mortar 1:5. (1- Cement : 5 -fine sand)in 75.043 3981.21 Cmt.

foundation and plinth (B)Conventional

7_A Extra for brick work in superstructure above plinth level upto

floor two level (B) Conventional 30.00 272.25 Cmt.

8 Half brick masonry in common brunt clay building bricks

having crushing strength not less than 35 Kg/Sq.Cm.in

Cement mortar1:4(1-Cement:4-coarse sand) in foundation 4.50 593.90 Sqm

and plinth (B) Conventional

9 Providing and laying polished kota stone slab 25 mm thick in

risers of steps,skirting,Dedo and pillars laid on10 mm thick

cement mortar1:3 (1-Cement:3coarse sand) and jointed with 58.50 1176.03 Sqm

gray cement slury mixed with pigment to match the shade of

slab including rubbing and polishing etc.complete.

10 Providing and laying white glazed tiles 6mm thick in flooring

treads of steps and landing laid on a bed of 12mm thick

cement mortar 1:3 (1-cement : 3- coarse sand ) finishing with 30.30 908.17 Sqm

flush pointing in white cement.

11 Providing and laying white glazed tiles 6mm thick in skrting

risers of steps and dedo on 10mm thick cement plaster 1:3 (1-

cement:3-coarsesand) and jointed with white cement slurry 20.75 1044.23 Sqm

12 Providing and layingCeramic tiles 6mm thick in skrting risers

of steps and dedo on 10mm thick cement plaster 1:3 (1- 20.15 1028.11 sqm

cement : 3-coarse sand) and jointed with white cement slurry

13 Providing and laying broken chine mosaic flooring for terrace

using 12mm to 20mm broken pieces of glazed tiles to be laid

over cement mortar1:3 top lain or slope and to be tempered to

bring mortar creme out up to surface using white cement 58.21 739.89 Sqm

including rounding off junctions and extending them upto

cm along the wall,clearing with water and oxalic acid etc.as

14 Providing 15mm thick cement plaster in single coat on Rough

(Similar) side of single or half brick walls for interior plastering

upto floor two level and finished even and smooth in (ii)

Cement mortar 1:3 (1-cement :3-sand)

15 20 mm thick sand faced cement plaster on walls upto height

10 meters above ground level consisting of 12 mm thick

backing coat of C.M.1:3 (1-cement : 3-Sand) amd 8 mm thick 121.67 297.68 sqm

finishing coat of C.M.1:1 (1-cement : 1-Sand) etc complete.

16 Finishing wall with weather proof exterior emulsion paint on

wall surface (two coats) to give an required shape even shade

after thoroughly brushing the surface to remove all dirt, and 121.67 113.40 sqm

remains of loose powdered materials .etc complete (Orange

Vision X110 & Soothing Sapphire_7326)

17 Wall painting (two coats) with plastic emulsion paint of

approved brand & manufacture on undercoated wall surface

to give an even shade including thoroughly brushing the 187.69 78.44 sqm

surface free from mortar droppings and other foreign matter

and sand papered smooth.

18 Applying two coats of putty & two coats of primer of approved

brand and manufacture on new wall surface to give an even

shade including thoroughly brushing the surface free from 187.69 40.19 sqm

mortrd ropping and other foreign matter and sand papered

19 Providing laying and jointing in true line and level -

dia.U.P.V.C.Pipe (SCH-40) for cold water including fittings

make PRINCE/SUPREME/ASTRAL/FINOLEX or equivalent

as approved by Engineer In Charge.Pipe shall be fixed on the

wall with the help of clamp at every two metre C/C or shall be

concelled as directed including necessary fittings etc.including

testing of pipe and joints and fixing the same with adhesive

solvent,including cost of all materials.

20 Making hole on existing CI/DI/MS water pipe line including

nacessary GI fittings item also includes necessary excavation,

dewatering and refilling as per instruction Engineer In charge

21 Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2

working pressure polythene pipes of the following outside Dia.

Low densidy, complete with special falnge compression type 5.00 274.68 Rmt

fittings, wall clipsetc. including making good the wall ceiling

and floor.(F) 75mm

22 Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2

working pressure polythene pipes of the following outside Dia.

Low densidy, complete with special falnge compression type 10.00 332.91 Rmt

fittings, wall clipsetc. including making good the wall ceiling

and floor.(G) 110mm

23 Providing and fixing water closets quatting pan (Indian type

W.C pan) size 580 mm (earth work,bed concrte,foot rests and

trap to be measured and paid for seperately)(A)Vitreous 1.00 926.10 Each

China (I) Long pattern white colour.

24 Providing and fixing wash basin with single hole for pillar tap

with C.I.or M.S.brackets painted white including sutting holes

and making good the same but excluding fittings.(A) Vitreous 1.00 1400.18 Each

China:(ii) Flat Back wash basin 550mm x 400mm size.(i) In

25 Providing and fixing S.W.gully trap with C.I.grating brick

masonry chamber and water tight C.I.cover with frame of

mm x 300 mm size (inside) with standard weight.(i) Square 1.00 1234.57 No

mouth traps.(B)150 mm x 100 mm size P or R type

26 Providing erecting and fixing double coated Syntex

PVC.(ISI)water tank of required capacity each with all

necessary fittings and connection etc. complete on terrace. 1000.00 3.91 Litre

27 Providing and fixing screw down bib taps of following size.(A)

Brasss crew down bib tap polished bright. (i) 15mm dia. 4.00 184.98 Each

28 Providing and fixing cast iron (Spun) Nahni trap of the

following nominal diameter of self cleaning design with

C.I.screaed down or higned grating including cost of cutting 3.00 600.08 Each

and making good the walls and floor100 mm inlet and 50 mm

outlet.(C)100mm dia.

29 Providing and fixing chromium plated,bottle trap with

necessary couplings of approved quality for wash basin. 1.00 292.87 Each

30 Providing and fixing ball cock of approved.quality as

directed.(A) Copper Metal (i) 25mm dia. 1.00 131.57 Each

31 Provdg. & laying S.W. Gully trap with brick masonry chamber

& water tight G.T.Stone including fixing of covervSquare 3.00 1279.40 No.

mouth trap 100 mm x100 mm size P-Trap

32 Making connection to the ex.M.H.in running sewer incl.

Dewatering and other required machinery etc. of following dia

pipes at any convenient time. All damaged work shall be well 2.00 1195.79 No

repaired as per instructions. etc..complete.

33 Providing and jointing stoneware pipes including excavation

upto 2 Mt. refilling, transporting pipes to

worksite,unloading,lowering in trench,jointing material such as

cement,sand,hemp bitumen as directed,including watering the

trenches spreading and carting away of surplus material as

directed by engineer in charge.

(C) 230 mm. diameter. 25.00 357.63 Rmt

34 Constructing brick masonry chamber for under ground

C.I.Inspection chamber and bends with bricks having croshing

strength not less than 35 Kg.Cm 2 in C.M.1:5 C.I.cover with

frame (Light duty ) 455 mm x 610 mm intenal dimensions total

weight of cover with frame to be not less than 38 Kg.(Wt.of

cover 23 Kg.) and Wt.of frame15Kg.) (R.C.C.top slab

with1:2:4 mix (1-cement:2-coarse sand:4-graded stone 3.00 2903.89 Each

aggregate 20 mm size) foundation concrete1:5:10 in side

plaster15 mm thick with cement mortar1:3 finished smooth

with a floating coat of neat cement on walls and bed concrete

etc.complete.(i) Inside dimensions 455 mm x 610 mm and

mm deep for single pipe line.

Extra over items code 24016AA for every additional depth of

0.1M.of part there of beyond 450 mm depth for Brick masonry 0.00 239.99 Each

chamber.(i) for 455 mm x 610 mm size.

35 Constructing a sink (chowkedi) with C.C.1:2:4,12cm.thick over

B.B.masonry in C.M,(1:6 ) in front and dwarf wall 1.0 Mt.high

and 23 cm.thick cement plaster to masonry/in C.M.1:3) and 1.00 2235.66 No

cement concrete flooring in 1:2:4:mix 5 cm.dia.drain pipe

etc.complete.(at health dept and MH Dept)

36 Supplying and fixing of 380 mm H x 300 mm L x 200 mm

B Kerb Block for Central Verge in M-20 grade using

mm nominal size black trap aggregate of Sevaliya/Timba

or equivalent quality for pre-cast blocks, reasonably

exposed finish/ formwork, mould with well equipped with

vibratory system for kerb stones of approved design

including curing, etc. complete, including the cost of

formwork etc. complete. The rate shall also include

necessary cutting of asphalt, fixing the Kerb stones in

line and level on 5 cm thick sand bedding with necessary 35.00 431.96 Rmt

equipments and materials. The rate shall also include the

flush pointing in CM (1:3) for all joints of the kerbstones.

Filling of zari alone the sides of the kerb stone fixed with

Bituminous concrete mixed in proper position as directed

by Engineer in change to form a portable mixture. In any

case Gravel or such type of materials shall not be

allowed for productiona) Laying on 5 cm thick Sand

37 Providing and Laying of Rubber Moulded Paver Block

Grey/Coloured 60 mm thick, M-35 Grade of any size ; shape

(Usually Uni-Paver Blocks) using black trap good quality

aggragate of 20 mm nominal size for footpath, parking areas,

service lanes and other areas as mentioned in the

drawing/instruction of engineer in charge. Cost includes

formworks using rubber mould, Rate providing and laying

paver blocks as per required grading and specification. The

paver block shall be mechanically compacted. The work of

paving blocks shall be executed in line and level by skill 70.00 501.60 Smt

mason of flooring work only. It should be laid in such a way

that the no cutting of the paver block to be necessary. if

cutting of paver block necessary then it should be cut by

machine only and carting. The finished surface of the paver

block shall have resonably good, plain finished. Paver blocks

shall be compacted and shall be relaid if necessary. Gravel or

such type of materials shall not be allowed for production.

Laying on 5cms thick sand beddding.

38 Providing and fixing M.S. grills M.S. flats at required spacings

and frame alround, square or round bars with round headed 1000.00 100.17 kg.

bolts and nuts or by screws (A) Plain Grill.

39 Carring out plinth treatment to post construction / existing

structure by spraying chemical solution for termite control

treatment including labour and material consistment with I.S.I

specification. Using Chlordene and Chiorpurfiles 20 EC. As

Per 6131_paret-II Consentration Weight one percent is

recommended i.e one litre 20 EC chemical emulsion with

liter give 1 % concrentration inclusive of one litre chemical

emulsion appication at the rate of 5 Litre chemical / Sqm of

surface is recommended as per I.S

40 Marble Slab Polished granite stone 20 to 25mm thick black

41 Painting the kids picture chart & letter writting of different size

and shapes as per details/design etc.comp. as dire.by 1.00 5803.57 wall

engineer in charge

TOTAL PART-(A) CIVIL WORK Rs.

ELECTRICAL WORKS_PART-(B)

1 Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of

1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS

PVC insulated multi strand copper wires up to 10 mtr length

in below type of pipe erected with 6A Modular type switch /

bell push & accessories and earth continuity of following type,

erected on PVC / Metallic/Wooden box, single mounting base

frame covered with textured/metallic/white front plate

modules erected on / in wall

/ ceiling as per pipe erected, with necessary Lamp

holder/ceiling rose / H.D.Connector as

(e) in existing pipe erected flushed on wall/ceiling complete

Cat III 21.00 344.64 Pt.

2 Point wiring for FAN with 2-1.5 sq.mm & earth wire of

sq.mm (Green) both are of .ISI marked 1.1 KV Grade FRLS

PVC insulated multi strand copper wires up to 10 mtr length,

in below type of pipe erected with 6A Modular type switch

and hum free EME step type electronic fan regulator

mounted and accessories with earth continuity of following

type erected on PVC / Metallic/Wooden box, single mounting

base frame covered with textured/metallic/white front plate

modules erected on / in wall / ceiling as per pipe erected. with

necessary ceiling rose / H.D.Connector as directed.

(e) in existing pipe erected flushed on wall/ceiling complete

Cat III 9.00 483.93 Pt.

3 Point wiring for Individual Plug with & earth wire of 1.5 sq.mm

(Green) both are of ISI marked 1.1 KV grade FRLS PVC

insulated multi strand copper wires up to 10 mtr length, in

below type of pipe erected complete with Modular type switch

& 5 pin Plug erected on PVC / Metallic/Wooden box covered

with appropriate front plate modules erected on / in wall /

ceiling as per pipe erected with following type of accessories.

3.1 [I] For 6A Plug and 6 a switch with 2-1.5 sq.mm Cu. Wire

from nearby switchboard/mcb db

(e) in existing pipe erected flushed on wall/ceiling complete

3.2 [II] For 16A Plug and 16 amp switch with 2-2.5 sq.mm Cu.

Wire from mcb db board.

(e) in existing pipe erected flushed on wall/ceiling complete

4 Point wiring for on board Looped Plug with 6A Modular type

switch & 5 pin socket erected on PVC / Metallic/Wooden

box, single mounting base frame covered with textured / 5.00 237.50 Pt.

metallic/white front plate modules erected on / in wall /

ceiling with following type accessories

5 Providing and erecting ISI mark Medium class RIGID PVC

PIPES of following size complete to be erected on/in wall or

ceiling erected with necessary PVC fittings & Junction boxes

fixed with adhesive solution & Clamps with following dia

of pipes, in approved manner as

6 Providing and erecting Mains with 1.1 KV grade FRLS PVC

insulated ISI marked stranded Copper conductor wire in

following type of pipe to be erected concealed in /flushed on

wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC

insulated stranded wire of green

colour for earth continuity of following size

(A) with medium class Rigid PVC pipe and accessories

7 Providing and erecting XLPE (IS:7098)(I)-88 ISI

armoured cable multistrand / Solid Aluminium conductor

for 1.1 KV. to be laid on wall with necessary clamps or

trench / pipe of following size of cables

(c)4 core 10.0 Sq. mm 10.00 142.86 Mtr

8 SITC of 14.2 mm dia 3 mtr long Earth electrode of High

tensile steel electrode with 250 micron copper bonding &

bag of Carbon fill Based environment friendly backfill tested

as per IEC 62561-7 in NABL accredited Laboratory and

suitable stainless Steel double sided clamp. Eco Friendly 1.00 6250.00

rust proof heavy duty weather proof Polyethylene Earth Pit

Chamber with following dimensions :254 mm dia (top),

mm dia (bottom) & 260 mm (height).

9 Supplying and erecting LED indoor fittings with LEDs of

wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB,

with housing used as a heat sink shall be made of thick sheet

Steel conforming to IS: 513/CRCA/aluminium pressure die

cast powder coated and high

U.V. & corrosion resistance with diffuser housed in

aluminium casted body with company mark/name

160V to 270V,Power Factor more than 0.9, THD < 15 %, CCT

Luminaire efficacy> 85 lumens/watt , LED driver efficiency >

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below

description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage

between the ranges shown.)

(A) Tube Light with integral driver (ii) 18-20 Watts, Surge -

2KV,IP-20, conventional 4 feet 15.00 339.29 Ea.

10 Supplying and erecting LED indoor fittings with LEDs of

wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB,

with housing used as a heat sink shall be made of thick sheet

Steel conforming to IS: 513/CRCA/aluminium pressure die

cast powder coated and high

U.V. & corrosion resistance with diffuser housed in

aluminium casted body with company mark/name

160V to 270V,Power Factor more than 0.9, THD < 15 %, CCT

Luminaire efficacy> 85 lumens/watt , LED driver efficiency >

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below

description have shown ranges

of Wattage capacity of LED fittings.The Engineer incharge

may select any wattage capacity between the ranges shown.)

(A) Square/ Circular shaped Surface/Recessed Mount

Downlight with provision for spring

loaded mounting clips complete.IP20

(i) 5-9 watts,Surge-2 KV Cat-lll 2.00 250.00 Ea.

10.2 (ii) 11-15 watts, Surge-2 KV Cat-lll 4.00 491.07 Ea.

11 providing and erecting Miniature circuit breaker single pole 6A

to 25A suitable to operate on 240 V A.C. system and having

breaking capacity 10 KA to be erected in existing 6.00 116.07 Ea.

box.confirming to IS 8828/1996 with ISI Mark

12 Providing & erecting 240 V MCB double pole switch for motor

& inductive load (C Curve)

having 10 KA breaking capacity & confirms to IS :

in existing box having following capacity

12.1 (a) 6 to 32 Amp. Cat.III 1.00 312.50 Ea.

12.2 (b) 40 Amp. Cat.III 1.00 343.75 Ea.

13 Providing and erecting Sheet Steel powder coated

MCB distribution board - flush / surface mounted fitted with

busbar, neutral link, earth bar and DIN rail, confirming to IS

8623-1&3, and iec61439-1&3 without MCB to house

appropriate nos.of MCBs(The DBs should be used of same

company of MCB to be used) suitable for (A) single phase

incoming and horizontal single phase outgoing (IP-43)

13.1 (i) Single phase 4way SS Double door 1.00 655.36 Ea.

14 providing and erecting Approved make ELCBs / RCCBs

conforming to IS: 12640 and having sensitivity of 30 mA and

Short Circuit withstand capacity of 10 KA and suitable for

operation on single phase 240 V,50Hz. having characteristic

of quick action & tripping with all advance feature & do not

incorporate any electronic component. for following Max.

14.1 (ii) 40Amps. DP Cat. III 1.00 2330.36 Ea.

15 Supplying & erecting approved make low noise decorative

exhaust fan having size 200mm with 1350 RPM with square 4.00 1776.79 Ea.

frame ABS body with inbuilt lowers & square frame. CAT-III

16 Providing and erecting Approved make Ceiling fan with double

ball bearing ISI mark with condenser A.C. 23OV.50 c/s.1200

mm. sweep complete, canopy erected on existing hook or 5.00 1517.86 Ea.

clamp with earthing. [Make shall be approved by Engineer in

17 Supplying & erecting fan hook box of 10 mm M.S. round bar

bounded to the RCC bars up to 50mm length each side and

pierced through a 16 Gauge M.S. box / Heavy Duty PVC box

complete erected concealed in Ceiling with necessary

18 Supplying and erecting 19 / 20 mm. nominal bore Medium

Class M.S. Pipe down rod erected duly painted for fan 5.00 111.61 Ea.

complete with proper insulation without leakage and earthing.

19 Providing & erecting open well type horizontal mono block

pump set with stainless steel body having following

specification(A) 0.5 H.P. single phase open well motor pump

set having discharge of 115 LPM @ 15 mtr. head suitable for

32 mm dia. delivery pipe with control panel including 3core

flat cable ofrequired size of length 5 Mtr.

20 Supplying & erecting approved make Automatic liquid level

controller 6A. with sensor testing as per instruction of

Engineer in charge on site complete with wiring connection 1.00 2419.64 Ea.

with existing wires , with copper conductor from pump to

upper and lower tank.

TOTAL PART-(B) ELECTRICAL WORKS Rs

PART-(C ) DEMOLATION OF WORK OF EXISTING STRUCTURE

1 Demolition incl. stacking of serviceable materials & disposal of

unserviceable materials with all lead and lift.

(a) R.C.C. work 20.00 1047.38 Cmt.

(b) Brick work & Stone Masonary in Cement mortar 35.00 544.95 Cmt.

(c) Tiles or Stone flooring 100.00 47.25 Smt.

(d) Sheet roofing (G.I. ) 156.00 47.25 Smt.

(e) Doors,Windows ventilators (wood/steel) Not Exiding

2 Removing and scraping of old deteriorated plaster of any

thickness from wall / R.C.C member including stacking of

serviceable material and disposal of unserviceable from site of

work with all lead and lift

TOTAL PART-(C) DEMOLATION OF WORK OF EXISTING STRUCTURE Rs.

Total A + B + C

 Estimate for Construction of one new Typical Anganwadi is Rs, 13,20,086.06,

which may very as per site conditions. Total tender Value of Empanelments is Rs.

Note: Contractor Should quote unit rate mentioned as above. The payment will be made on

actual item wise execution as per the abstract attached here with and the same % rate

will be applicable for individual items as mention in abstract.

Contractor’s Quoted Rate: -

Net Quoted Tender Amount Rs.

Seal and Signature of the Bidder Addl. City Engineer

Date: ( East Zone)