REPAIR / REPLACEMENT OF JOINERY, FLOORING, PLINTH PROTECTION, CB SHUTTERS, STEEL WINDOW, ROOF TREATMENT, ATT, SANITARY FITTING, FLOOR/ WALL TILES, RAIN WATER PIPES, SUNKEN FLOOR TREATMENT ETC IN RESIDENTIAL AREA AT IRDE UNER GE(I) RND DEHRADUN

Amount

Taking down chowkats or frame of any description n.exc. 1.5 Sqm each (without taking off shutters from the frames) & remove off the premises complete all as specified and directed.

Taking down chowkats or frame of any description exc 1.5 Sqm each and n.exc 4Sqm (without taking off shutters from the frames) & remove off the premises complete all as specified and directed.

Taking down shutter exc. 1 Sqm and n.exc 2 Sqm each of any description complete all as specified and directed.

Taking down Shutters of any description exc 2 sq. m each of any description complete all as specified and directed.

Dismentling of wall and ceiling boards/ Alca panel /fibre/ pvc Board/PVC sheet panelling pulp, insulation etc or insulation boards/ slabs/blankets any thickness incl cover fillets, fittings, complete all as specified and directed

S&F factoty made 100% solid Wood Plastic composite (WPC) door frame of size 90mm x 45 mm made from wood plastic composite ( Single extruded Process ) materials with density 780 Kg/cum should be water proof,termite proof, fire retardant & having good screws holding capacity , complete all as specified and directed.

S&F Factory made wire gauzed PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles & plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panel will be of wire gauze. The wire gauze shall be wrapped on an additional square 8mm M.S Solid tube & this tube shall be welded to M.S tubes. The wire gauge shall be stretched to tighten firmly to be fitted in the M.S frame welded/ sealed to the stiles, & rails with suitable PVC sheet beading, & joined together with solvent cement, in the frame at site as per specification & drawing.

S&F factory made solid PVC flush shutters 32 mm thick ,made from co extruded three layer rigid PVC Sheet ( Single Extruded ) with density not less than 600 Kg/ Cum, outer layer ( 0.80-1 mm ) thick should be of rigid PVC with density of not less than 1400 Kg/ Cum Supplying and fixing in frame at site as per specifiecation & manufacture Instruction complete all as directed.

S&F factory made solid PVC moulded door shutters 28 to 30mm thick stiles), with 2,4 or 6 raised panel design with 2mm thick moulded PVC sheet on back face, with wood free EPS, Supplying and fixing in frame at site as per specifiecation & drawing shown in section 8 of SSR part-II complete all as directed.

S&F 35 mm thick second class hard wood factory made plain, framed panelled shutters (three Nos. of panel)with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and style as per IS-1003 (part-I), kiln seasoned and chemically pressure treated. complete all as specified and directed.

S&F 35 mm second class hard wood factory made glazed and skeleton shutters, open rebated and prepared to received glass, gauze, etc (without sash bars), edges of graming plain, chamfered or rounded, fitted with cut and mitred beads for securing glasss, etc : sizes of members of shutters as specified in SSR Part-I , Section 8, clause 8.24 (a) ; supplied and fitted to chowkats.

S&F 40 mm thick Flush shutters, solid core construction, with block board core & plywood face panels, commercial type on both sides complete all as specified and directed.

S&F powder coated aluminium sliding window three track with two glass shutters and one wire gauge shutter, aluminium powder coated section aluminium cleat, PVC track, bearing, handle locking arangement, rubber beading etc complte fittings as approved. Note Size of aluminium section shall be under :- (i) Three track top and vertical - Jindal or Equivalent main-2010 section No 20621 or equivalent (ii) Three track bottom- Jindal or Equivalent main-2010 section No 20620 or equivalent (iii) Shutter vertical section- Jindal or Equivalent main- 2010 Section 20606 or equivalent (iv) Shutter top and bottom - Jindal or Equivalent main-2010 Section 20604 or equivalent (v) Shutter vertical middle (interlock) -Jindal or Equivalent main-2010 section 20605 or equivalent

Dismantling wrought iron or mild steel work of any description not otherwise provided for

S & F framed work such as grills framed guard bars etc confirming to Fe-290, for guard bars .

M & L preparation of new steel or previously untreated surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as directed

S&F MS angle iron as in door frame work conforming to Fe 290(Gde E-165) including tie rod, hinges including one shop of red oxide primer etc. complete all as specified and directed.

S & F small articles of steel such as hold fasts, etc. of Gde Fe 410-O or Fe 310-O complete all as specified and directed.

M & L PCC 1:3:6 type C-1 as in coping, benching or bed blocks for hold fasts, etc complete all as specified and directed.

S&F 150mm size aluminium, anodised barrel tower bolt of extruded section.

S&F 300mm length, aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy.

S&F100mm size, butt hinges, medium weight, cold rolled mild steel.

S&F100mm size, butt hinges, Butt hinges, extruded brass, with mild steel hinge pin, bright polished and fixed, type B-11

S&F 150mm size extruded aluminium alloy handles, fabricated type.

S&F100mm size extruded aluminium alloy handles, fabricated type.

M&L for Preparation of new wooden surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer all as specifed and directed.

S&F in repair 24 mm thick solid factory made PVC board for cup board /cabinate ,shutter with one side prelaminated decorative lamination and other side balancing lamination sheet suitable fixed with & including suitable pvc frame,Stainless Screws, matching colured edge bonding tape to cover all edges , Magnetic catcher all as per specification & and manufacture instruction complete all as specified & directed.

S&F Brass handles 100mm size, cast type, polished bright as approved by Engr in Charge complete all as specified and directed

S&F 40 mm dia, brass, knobs for cupboard fixed with nut, screw and washer of mild steel, bright finised complete all as specified and directed.

S&F continuous (piano) hinges, mild steel, bright finish or electrogalvanised with width of flap (when open) 30 mm complete all as specified and directed.

S&F Brass Locks 2 levers, cupboard, grade I, size 50 mm complete all as specifed and directed.

S&F in repairs mild Steel 300mm, ordinary rat tail rod patttern springs including roller & roller plate complete fixed with screw or by welding complete all as specified and directed.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete.

S&F in repairs Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame incl punching or drilling out old glazing pins/spring clips and providing and fixing new ones.

M&L for 4mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 Sqm in each pane.

M&L for 4mm thick sheet figured glass, pin headed type and glazing with oil putty in square n exc 0.5 Sqm in each pane.

M&L for 4mm thick sheet glass, ordinary quality and glazing with oil putty in square or rectangular for Multistorey bldg upto G+5 storey with scafolding arrangments complete all as specified and directed

M&L for taking down/dismantling of existing roof treatment of any description such as PCC Padding/ Coba treatment/ mud phuska/Lime conc terracing including screed bed etc, Hessian base felt/tar felt etc. (any type and thickness) complete all as specified & directed.

Removal of demolished materials to a distance out side defence land at contractor own arrangement complete all as specified and directed .

M&L for rendering 15 mm thick in cement mortar 1:4 on roof surface including mixed with WPC as per manufacturer's instruction's and finishing the surfaces even and smooth without using extra cement complete all as specified and directed. Note :- WPC shall be measured and paid for separately as supply only under respectiveitem of sch 'A'.

M & L for water proofing treatment on roof slab including picking ,sweeping ,clean and washing down with water to remove dust & providing water proofing treatment described as under :- (a) Surface preparation and treating construction joints, filling of honey combs,preparation of coving ( if required ) with Asian paints smartcare Repair Mortor and Asian Smartcare General purpose Grout of Asian paint or equivalent product of THERMAX / FOSROC . (b) Cleaning the surface and appling Asian PU Magnum primer Resin & hardner of Make Asian paints or eqivalent product of THERMAX / FOSROC on the cleaned surface. (c) Appling Asian Smartcare PU Magnum of Make Asian paints in Two ( 2 ) layers ( PU Magnum per coat should be minimum of 600 gms per Square meter or equivalent product of THERMAX / FOSROC. ( d). Ponding test of 72 Hrs and no leakage/ seepage observed. Any rectification to be done at the cost of contractor repeating above stepsof application. (e) . The work shall be carried out complete as per manufacturer's specification and application methodolgy. (f) . Execution to be done with authorised applicator of the manufacturer and company back gurantee to br given by the contractor after completion of water proofing work befor payment. work will be executed in Smart Assurance System of manufacturer company of Asian/ Epoxy/ Polymer chemicals.

Dismantling floor , hearth or wall tiling including cement mortar bedding (but not backing), removing debrish and rubbish off the premises and stacking serviceable tiles .

M&L for glazed coloured ceramic tiles, first quality (or approved class, colour and design/shade) of size 300x200x7mm thick in vertical surfaces, as in dado/skirting etc set & jointed in neat cement slurry & pointed in coloured cement to match with coloured tiles, over and including 10mm thick rendering in cement mortar 1:4 rough finish to receive the tiles complete all as specified and directed.

M&L for glazed coloured ceramic tiles, first quality (or approved class, colour and design/shade) of size 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match with coloured tiles in vertical surfaces, as in dado/skirting etc , over and including 10mm thick rendering in cement mortar 1:4 rough finish to receive the tiles complete all as specified and directed.

M&L for non-skid coloured ceramic tiles first quality (of approved class, colour and design/shade) 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0. 06 sqm but not exceeding 0.11 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles including 15 mm thick cement screed bed in cement mortar 1:6 for laying floor finishes. complete all as specified and directed

M&L for non-skid coloured ceramic tiles first quality (of approved class, colour and design/shade) 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles including 15 mm thick cement screed bed in cement mortar 1:6 for laying floor finishes. complete all as specified and directed

M&L for Granite ( of any type) tiles 18 mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including griding and polishing typesincl screed bed or bedding layer of mortar 15 mm thick for laying floor finishes in CM 1:6 complete all as specified and as directed .

M&L for post construction ATT along the external wall below concrete or masonary apron using chemical emulsion @ 2.25 litres per linear metre incl drilling and plugging holes etc in apron complete

M & L for treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement :2 coarse sand) to match the existing floors

M&L post construction ATT at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.50 litres/hole by driling 6 mm dia holes at a downward angle of 45 degree at 150 mm centre to centre and sealing the same complete

Taking down old curtain rods/ drapery rods of any description and S&F drapery rod 32 mm dia, high Strength aluminium rod with powder coated paint of thickness 40/60 microne of wood finish with minimum 8 rings in each metre length of rod of ABS Plastic in matching colour & installations brackets of galvanised steel, powder coated paint in matching colour with all accessories complete all as specified and directed.

Taking down cement or cement lime plaster of any description including racking out joints, hacking for keys , scrubbing down with water etc, complete all as specified and directed.

M&L for Rendering 15 mm thick on fair faces of concrete/brick surfaces in cement mortar 1:4 mixed with water proofing compound as per manufacturer's instruction, finished fair and even without using extra cement complete all as specified and directed. Note :- WPC shall be measured and paid for seprately as supply only under respective item of sch A.

M&L for Rendering 15 mm thick on fair faces of concrete/brick surfaces in cement mortar 1:6 finished fair and even without using extra cement complete all as specified and directed.

M & L for preparation of newly plastered surfaces of walls and applying two coats of cemend based paint over a coat of suitable primer complete all as specified and directed.

M & L for preparation of newly plastered surfaces of walls and applying two coat of distempered oil emulsion over a coat of suitable primer incl 3 mm thick wall care putty fall as directed by Engr-in-Charge .

Demolition of cement concrete (unreinforced) of any description as in ground floors and pavings not exceeding 15cm thickness (above or below ground floors) complete all as specified and directed

M & L for providing plain cement concrete, type E-2, 1:5:10 (using 40 mm graded brick aggregate) as in sunken, filling and mass concrete complete all as specified and directed.

M&L 25mm PCC 1:2:4 Type B-0 (Using 12:5mm stone agg) as in base floor , complete all as directed and specified .

M&L for waterproffing treatment to sunkin portion of WC, bathroom etc by applying cement slurry mixed with Acrylic Based Polymer modified cementation composited compound coating as under :- First layer of cement @ of 0.488 kg per sqmtr mixed with Acrylic Based Polymer modified cementation composited compound @ 0.253 kg per sqmtr. This layer will be allowed to air cure fro 4 hours and second layer of slurry of cement @ 0.242 kg per sqmtr mixed with Acrylic Based Polymer modified cementation composited compound @ 0.126 kg per sqmtr and allowed to be air cure for 4 hours including preparation of surfaces treated and sealing all joints , corner , juncation , pipes and masonory with Polymenr mixed slurry joints, corner, juncation , pipes and masonry with Polymer mixed slurry . (Treatment will be allowed with water curing for 48 hours ).

M&L for Running welding in repairs Thickness of metal to be welded n exc 6mm coplete .

S&F in repairs mild Steel 300mm, ordinary rat tail rod patttern springs including roller & roller plate complete fixed with screw or by welding complete all as specified and directed.

M/L for taking down existing steel window Z section shutter by cutting projected type MS hinges and refixing/ irrecting the same by welding box type MS hinge 2 Nos in each shutter including necessary arrangement for works upto 4th story.

Taking up or down 15 mm steel tubing and connections,including cleaning for refixing or removal to store complete all as specified.

S & F 15 mm bore of tube medium grade galvanized with all fittings & fixed complete to walls & ceiling or laid in floors.

M&L for refixing old steel tubing and connections in new or old position (walls, ceiling, floors, etc.) for 15 mm dia pipes with and including all new fittings complete all as specified and directed. Note:- GI pipe shall be reused, received under Item No.65 here in above.

Taking up or down 20 mm steel tubing and connections,including cleaning for refixing or removal to store complete all as specified.

S & F 20 mm bore of tube medium grade galvanized with all fittings & fixed complete to walls & ceiling or laid in floors.

M&L for refixing 20 mm dia (Nominal bore) galvanised iron water tubing 'medium grade' with and including all GI fittings such as unions, reducer sockets, socket reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed complete to walls and ceilings or laid in floors complete all as specified and directed.Note:- GI pipe shall be reused, received under Item No.68 here in above.

S&F in repair Galvanised sheet water tank covers including nut-bolt, hinges, Hasp & staple, handle etc suitable for water tanks of Cap 500 ltrs to 1000 ltr as per sample kept in AGE office complete all as specified and directed.

Disconnecting & taking down existing water tank of capacity exc 250 liter and not exc. 500 liter and removing from site complte and S&F rotational moulded polyethylene water storage tanks 500 lts capacity (cylindrical vertical with closed top) hoisted with and including 20 mm dia ball brass valves, high pressure with polythene float and fly nut complete screwed for iron pipe or for brass ferrule and fixed in position all as per SSR Part I complete all as specified & directed.

Disconnecting & taking down existing water tank of capacity exc 500 liter and not exc. 1000 liter and removing from site complte and S&F rotational moulded polyethylene water storage tanks 1000 lts capacity (cylindrical vertical with closed top) hoisted with and including 20 mm dia ball brass valves, high pressure with polythene float and fly nut complete screwed for iron pipe or for brass ferrule and fixed in position all as per SSR Part I complete all as specified & directed.

S&F in repair Ball valves 15mm bore high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe & fixed. (min. weight 15mm-142 gms)

Dismantling of cast iron, SGSW, PVC or reinforced concrete drain pipes jointed in neat cement mortor and taking out of trenches or floor or wall if required

S&F PVC (SWR) pipe 75 mm bore, single socketed , in any length with rubber ring joints and jointed with approved adhesive and laid in treanches or in floors complete all as specified and directed.

S&F PVC (SWR) pipe 110 mm bore, single socketed , in any length with rubber ring joints and jointed with approved adhesive and fixed to wall complete all as specified and directed.

S&F PVC (SWR) pipe 150 mm bore, single socketed , in any length with rubber ring joints and jointed with approved adhesive and fixed to wall complete all as specified and directed.

S&F PVC (SWR) pipe 200 mm bore, single socketed , in any length with rubber ring joints and jointed with approved adhesive and fixed to wall complete all as specified and directed.

S&FPVC (SWR) bend/shoe 75 mm dia, any radius as required and jointed with approved adhesive and fixed to floor complete all as specified and directed.

S&F PVC (SWR) Tee, Reducer/junction (single T) equal or unequal 75 mm dia, any radius as required and jointed with approved adhesive and fixed to floor complete all as specified and directed.

S&F PVC (SWR) bend/shoe 110 mm dia, any radius as required and jointed with approved adhesive and fixed to wall complete all as specified and directed.

S&F PVC (SWR) Tee, Reducer/junction (single T) equal or unequal 110 mm dia, any radius as required and jointed with approved adhesive and fixed to wall complete all as specified and directed.

S&F PVC (SWR) bend/shoe 150 mm dia, any radius as required and jointed with approved adhesive and fixed to wall complete all as specified and directed.

S&F in repair PVC (SWR) Tee, Reducer/junction (single T) equal or unequal 150 mm dia, any radius as required and jointed with approved adhesive and fixed to wall complete all as specified and directed.

S&F PVC (SWR) bend/shoe 200 mm dia, any radius as required and jointed with approved adhesive and fixed to wall complete all as specified and directed.

S&F in repair 75 mm dia PVC (SWR) floor trap , plain with grating including jointing with solvent cement .

Cleaning and removing all scale and dirt, etc. from tanks and form mouths of circulating pipes, etc., capacity of tank exc 250 & n exc 500 litres including writing date of cleaning on the tank with suitable synthetic enamel paint etc complete all as specified and directed.

Cleaning and removing all scale and dirt, etc. from tanks and form mouths of circulating pipes, etc., capacity of tank exc 500 & n exc 1000 litres including writing date of cleaning on the tank with suitable synthetic enamel paint etc complete all as specified and directed.

Supply only integral water proofing compound ISI marked complete all as specified and directed..

Taking down shutter n.exc 1 Sqm each of any description complete all as specified and directed.

S&F powder coated anodised aluminium frame for doors, windows, ventilators & partition with one or more rebates including joining cleat for fixing etc. complete all as specified

S&F powder coated anodised aluminium window and ventilator shutters, side hung type without sash, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing , anodised aluminium snap, rubber packing , anodised aluminium snap beading , screws , anodised aluminium fittings such as peg stays 150 mm long (1 No), hinges type B-21 100 mm long (2 No) suitable handle (1 No) complete all as specified and directed.

S&F Factory made fully louvred PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles & plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panel will be of fully louvred. The M.S frame welded/ sealed to the stiles, & rails with suitable PVC sheet beading, & joined together with solvent cement, in the frame at site as per specification & drawing.

M&L for coloured 3D/2D PVC vinyl wall cladding/ covering/wall paper minimum 3 mm /5 mm thick fixing on vertical surface/ horizontal surface on wall/ceiling with necessary adhesive/fitting, fixtures or as per manufacturer instructions complete all as specified and directed

S&Fof table top vitreous china wash basin 550 x 400 mm size, flat back including one number chromium plated waste fitting, 32 mm dia, brass with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed, with and including 32 mm dia PVC waste pipe with connector, MS brackets 2 numbers including cutting for and pinning in ends of brackets complete all as specified and directed.

Pantech Instruments and Services

Gaur Construction Co

Amit Associates