Construction of Gplus2 Administrative building to accomodate O/o the DGM,Silchar TandT Circle,O/o the AGM Silchar TandC Division and O/o the AGM,Silchar TandT Division at 132 kV GSS Campus,Srikona,AEGCL

Amount

Civil Works

Site cleareance :- Jungle clearing,cutting and trimming of tree and removal of the tower angles, cable etc. or another other matterial by mannual or machinical means and stacking serviceable materials at a place specified by AEGCL and cleaning site etc. Complete as directed.

Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified. Up to a depth of 1.00 m below the existing ground level. In hard/ dense soil

Providing brick soling in foundation and under floor with stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete. (a) Brick on flat soling.

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately). In prop 1cement: 3 sand :6 coarse aggregate by volume

Supplying, fitting and fixing in position reinforcement bars conforming to relevant IS code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes ………………and placing in position with proper blocks, supports, chairs, spacers etc. complete. (up to 1st floor level). (a) From Primary Producer: TATA/SAIL/Esser Steel/ Jindal steel/Shyam steel/RINL . (i) TMT Corrosion resistant steel (CRS) reiforcement bar

Ground floor

First Floor

Second floor

Tarrace to Stair case head room Roof

Providing form work of 12mm thick Plywood Board so as to give a rough finish including centering, shattering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in situ reinforced concrete and plain concrete work in:

Upto first floor Columns, Pillars, Posts & Strut of square/ rectangular/ polygonal in plan or any shape like Tee/L etc. having plane vertical face

Upto first floor Sides and Soffits of Beams, beam haunchings, cantilever girders, bressumers, lintels and horizontal ties. For depth not exceeding 1.0M.

Upto first floor Flat Surfaces such as soffits of suspended floors, roofs, landings, cantelever slabs, chajjas, balconies and the like. Floors etc. upto 200mm in thickness.

First floor to 2nd Floor Columns, Pillars, Posts & Strut of square/ rectangular/ polygonal in plan or any shape like Tee/L etc. having plane vertical face

First floor to 2nd Floor Sides and Soffits of Beams, beam haunchings, cantilever girders, bressumers, lintels and horizontal ties. For depth not exceeding 1.0M.

First floor to 2nd Floor Flat Surfaces such as soffits of suspended floors, roofs, landings, cantelever slabs, chajjas, balconies and the like. Floors etc. upto 200mm in thickness.

At 2nd floor to Terrace Columns, Pillars, Posts & Strut of square/ rectangular/ polygonal in plan or any shape like Tee/L etc. having plane vertical face

At 2nd floor to Terrace Sides and Soffits of Beams, beam haunchings, cantilever girders, bressumers, lintels and horizontal ties. For depth not exceeding 1.0M.

At 2nd floor to Terrace Flat Surfaces such as soffits of suspended floors, roofs, landings, cantelever slabs, chajjas, balconies and the like. Floors etc. upto 200mm in thickness.

Tarrace to Head Room Top Slab Columns, Pillars, Posts & Strut of square/ rectangular/ polygonal in plan or any shape like Tee/L etc. having plane vertical face

Tarrace to Head Room Top Slab Sides and Soffits of Beams, beam haunchings, cantilever girders, bressumers, lintels and horizontal ties. For depth not exceeding 1.0M.

Tarrace to Head Room Top Slab Flat Surfaces such as soffits of suspended floors, roofs, landings, cantelever slabs, chajjas, balconies and the like. Floors etc. upto 200mm in thickness.

Providing and laying Plain/Reinforced cement concrete works in prop 1:2:4 including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete works (shuttering where necessary shall be measured and paid separately). Using mixture machine.

In substructure up to plinth level Foundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level. Without using admixture, plasticiser. M20 grade concrete or Prop. 1:1.5:3

in superstructure At Ground floor M20 grade concrete or Prop. 1:1.5:3

in superstructure at 1st floor M20 grade concrete or Prop. 1:1.5:3

in superstructure at 2nd floor M20 or Prop1:1.5:3

in superstructure at 3rd floor M20 or Prop1:1.5:3

230mm thick brick wall in cement morter with 1st class brick including racking out joints and curing complete as directed in structure (I) In Sub-structure upto plinth level including dewatering if necessary (c). In proportion 1:5.

Providing and laying 25mm thick damp proof course with cement concrete in prop 1:1.5:3 with graded stone agg. of 10mm down nominal size including providing approved damp proof admixture in proportion as recommended by the manufacturer including curing etc. complete as directed.

1st class brick nogged wall in cement mortar including racking out joints and curing complete as directed in super structure above plinth up to 1st floor level (protruding M.S rod/Tor steel of column to be embeded in cement mortar and will be measured and paid separately). 112mm thick brick wall. In cement mortar in proportion 1:5.

Ground level

First Floor

Second Floor

Third Floor

1st class brick nogged wall in cement mortar including racking out joints and curing complete as directed in super structure above plinth up to 1st floor level (protruding M.S rod/Tor steel of column to be embeded in cement mortar and will be measured and paid separately). 75 mm thick brick wall In cement mortar in proportion 1:5. (1 cement:5 sand)

Pre construction anti - termite treatment by applying in the entire levelled area after plinth filling and before laying floor by applying the emulsion @ 5 (five) litres per square meter of the surface to be spread with light rodding so as to ensure proper absorption by the filled up earth (supplying of necessary tools and accessories by the contractor) as per the direction of the Department complete.

Earth/ sand filling in plinth in layers not more than 150mm thick including necessary carriage, watering, ramming etc. complete as directed and specified including payment of land compensation, forest royalty, sales tax and other duties and taxes as may be necessary. (a) With earth or silt or sand obtained by head load with lead upto 90m and lift upto 2m

15mm thick cement plaster in single coat on rough side of single or half brick wall for interior plastering up to Ist floor level including arises, internal rounded angles, not exceeding 80mm in girth and finished even and smooth including curing complete as directed. (B) On Fair side (b) In proportion 1:4

20 mm thick Cement plaster in two coats on single or half brick walls for interior plastering up to 1st floor level including arises, internal rounded angles,chamfers and / or rounded angles not exceeding 80mm in girth and finished even and smooth including curing complete as directed. B) On fair side (backing coat 10 mm and finishing coat 10mm thick) b) In cement mortar 1:4

Supplying, fitting, fixing and painting where necessary (one coat primer and two coats of paint) suspended ceiling which includes G.I. perimeter channels of size 0.55mm thick (having one flange of 20mm and another flange of 30mm and a web of 27mm) along with perimeter of ceiling, screw fixed to brick wall/ partition with the help of nylon sleeves and screws, at 610mm c/c. Then suspending G.I. intermediate channels of size 45mm (0.9mm thick with two equal flanges of 15mm each) from the soffit at 1220mm c/c with ceiling angle of width 25mmx10mmx0.55mm thick fixed to soffit with G.I.cleat and steel expansion fasteners. Ceiling section of 0.55mm thickness having knurled web of 51.5mm and two equal flanges of 26mm each with lips of 10.5mm are then fixed to the intermediate channel with the help of connecting clip and in direction perpendicular to the intermediate channel at 298mm c/c.

Providing VITRIFIED floor tiles of approved quality of specified size, shape and thickness not less than 18mm on floors, skirtings, risers and treads of steps over 15 mm thick base of cement mortar in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf) / white cement slurry mixed with approved pigment to match shade of tiles, mixed with approved pigment to match the shade of the tiles, complete at all levels as specified and directed. (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department) a) Normal range ii) 600mmx600mm and above

Providing polished ceramic wall tiles of approved quality, size, shape and thickness not less than 8mm on walls and skirtings over cement mortar bed 10 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey / Sika / Pedelite / Rouf) /white cement slurry mixed with approved pigment to match shade of tiles complete at all levels as specified and directed. (Cement plastering to be measured and paid separately). (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department). (Walls means both interior and exterior walls). (a) Normal range (Somany/Orient/Nitco/Asian make) (ii) Sizes 200 mm x 300mm and above

Providing Antiskid Tiles of approved quality size, shape not less than 8mm on floor, skirting over a cement mortar bed 15mm thick of 1:3 (1 cement: 3 coarse sand) approved make fix with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf)/ white cement complete at all level as specified and directed. (A) CERAMIC i) Normal range (Sizes 300 mm x 300mm and above)

Providing polished granite tiles of approved quality, size, shape and thickness not less than 18 mm on floors, skirtings, risers and treads of steps over 15 mm thick base of cement mortar in prop. 1:3 (1 cement : 3 coarse sand) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf) / white cement slurry mixed with approved pigment to match shade of tiles, mixed with approved pigment to match the shade of the tiles, complete at all levels as specified and directed. (Cement plastering to be measured and paid separately). (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department) (i) With Fix-A-Tile (Choksey/Sika/Pedelite/Rouf)

Providing plinth protection with bricks flat laid in cement mortar 1: 4 and finished with 15mm thick cement plaster in prop. 1:2 with a floating coat of neat cement finish.

Providing drain with brick work in cement mortar in proportion 1:5 with half brick thick side walls and 100mm thick C.C (1:3:6) base over one brick flat soling including 15mm thick cement plastering in prop. 1:3 finished with a floating coat of cement slurry as directed with necessary shttering for sides and earth work in excavation of foundation trenches and refilling the sides after completion of work etc. as specified. i). 300mm wide and average 150mm deep with bed slope 1 in 150 with initial depth of 100mm.

Providing two coats of Birla White Wall Care Putty (Water Resistant White Cement based putty for concrete/ mortar walls and ceiling both internal and external) after removing all loosely adhering material from the wall surface with the help of emery stone, putty blade or wire brush and moistening the wall with sufficient quantity of clean water as specified and directed by the department. (Total thickness of two coats is maximum 1.5mm) (ii)Thickness = 1.0mm thick

Applying one coat of cement primer of approved brand and manufacture on new wall surface after throughly brooming the surfaces free from mortar droppings and other foreign matter and including preparing the surface even and sand papered smooth.

Wall painting (two coats) with Plastic emulsion paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) on new surface to give an even shade after throughly brushing the surfaces free from mortar droppings and other foreign matter and sand papered smooth. (a).Plastic Emulsion Paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac)

Extra over item no 13.4.1 above for every subsequent coat of wall painting with acrylic emulsion paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac).

Finishing old/ new wall with water proofing weather coat smooth anti-fungal exterior painting of Nerolac Paints Limited of required shade on old/ new wall surface to give an even shade after cleaning and clearing the surface etc. including scaffolding complete as directed at all levels (two coats).

Painting two coats (excluding priming coat) on new steel and other metal surface with enamel paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J&N/ Nerolac) to give an even shade including cleaning the surface of all dirt, dust and other foreign matter. (i).Surfaces over 100mm in width or girth. a). General purpose (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac).

Providing and fixing rolling shutters (Meachanized) of approved make made of 80mm wide M.S. laths interlocked together through their entire lenth and jointed together at the ends by end-locks mounted on specially designed pipe shaft with bracket plates, guide channels and arrangements for inside and outside locking with push-pull operation complete including cost of wire, spring and hood cover for the shutters.

Supplying fitting and fixing M.S.angles, M.S. flat, M.S. bolts and nuts including painting with red lead paint one coat complete as directed.

Providing, fitting and fixing anodised aluminuim framed glazed doors with anodised aluminium frame made of 100mm x 45mm x 2.5mm section with door style of size 88mm x 45mm x 2.5mm, top rails 50mm x 45mm x 2mm and bottom rails 100mm x 45mm x 2.5mm fitted with glazing clip, special type rubber gasket complete etc complete with all necessary accessories such as godrej Lock, 18 " SS(304) handle ,5" SS(304) hinges,10" SS (304) L-Drop , screws, bolts etc. as complete as per drawing , specifications and direction of the Engineer In Charge. as specified and directed by the department at all levels. (a) with 12 mm thick toughened glass

Providing, fitting and fixing of Door made out of 30 mm thick Century block board with 1 mm thick matching Green land lamination pasted and 5.5 mm clear glass inserted with all necessary accessories such as godrej Lock, 18 " SS(304) handle , 5" SS(304) hinges,10" SS (304) L-Drop , screws, bolts etc. as complete as per drawing , specifications and direction of the Engineer In Charge.

Providing, fitting and fixing of Door made out of 30 mm thick Century block board with 1 mm thick matching lamination pasted with all necessary accessories such as godrej Lock, 18 " SS(304) handle ,5" SS(304) hinges,10" SS (304) L-Drop , screws, bolts etc. as complete as per drawing , specifications and direction of the Engineer In Charge.w complete as per drawing , specifications and direction of the Engineer In Charge.

Providing, fitting and fixing factory made wooden panelled doors with panel inserts of 75mm to 50mm width and 12mm to 20mm thickness,joined together with continous tongue and groove joints glued together with Movicol or other approved adhesive leaving a vertical groove of 7.5mm to 15mm between the inserts,the edges of panel inserts being feather tongue into styles and rails including providing three pairs of oxidised M.S butt hinges (100mm x75 mm x3.55mm) and furnishing with moulded timber beading of size 25mmx15mm around the panels complete as per drawing (moulded timber bead and all fittings except hinges to be paid separately). a) With Teak wood / Sissu wood. (i) 40 mm thick with panel inserts of 20mm thickness.

Providing, fitting and fixing White ivory powder coated colour aluminium (1.5 mm thick) sliding windows and ventilators of standard sections of approved brand without horizontal glazing bars,joints mitred and welded (manufactured to relevant IS specifications) and providing and fixing handles, angle cleat, rubber gasket, roller, bolting device, locking arrangements, screws etc as as per drawing and design.complete as specified and directed for all levels. (a) 2track/3 track/4 track sliding window with both end fix (i)5mm frosted toughened glass

Providing, fitting and fixing coloured anodised aluminium sliding windows and ventilators of standard sections without horizontal glazing bars,joints mitred and welded (manufactured to relevant IS specifications) and providing and fixing handles, angle cleat, rubber gasket, roller, bolting device, locking arrangements, screws etc as required complete as specified and directed for all levels. (a) 2track sliding window (iii) 6 mm clear glass

Supply and installation of Structure Glazing glass(6mm Royale Blue ST-750 Emarald glaze Reflective toughened glass) with the support of 4"x2" (1.5 mm thick) colour anodised Ac-2 alluminium (Jindal make) section and the glass will be fitted in a subframe of 19mmx 19mm and the area will be packed by silicon sealeant etc complete as per drawing,design and direction of In- Engineer Incharge .

Providing and fixing stainless steel (grade 304) railing system(Ht- 900 mm) and post at a spacing of 900 mm made of hollow tubes 40 mm top (1.5 mm thick) and 12 mm middle(2 nos-1.5 mm thick) and 12 mm bottom (1.5 mm thick) etc including welding, grinding buffing, polishing and making curvatures (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete i.e. fixing the railing with necessary assessories and stainless steel dash fashtenners, stainless steel bolts etc. of required size on the top of the floor for the side of waist slab with suitable arrangement as per approval of Engineer In-Charge. no extra payment for fixing assessories i.e. nuts, bolts, fastenners etc. will be considered.

Supplying fitting & fixing of partition wall made of allunium hollow section (60 mm X38mm X1.8 mm) frame, on face of it 19 mm thick block board (century make )& 12 mm (century make ) ply board is fitted with 1 mm thick matching lamination ,10 mm toughened glass is also fixed on the top etc complete with all accessories to complete the job as per thedesiggn, drawing and as directed by the department

Providing, fitting, hoisting and fixing of roof trusses fabricated out of combination of any two or all of the following sections (i) Square section (ii) Rectangular Hollow section of specification RSH/SHS and (iii) M.S. circular hlollow section of Grade 210 including purlins, bottom runners and providing M.S. cleat, M.S. angle base plank, bolts and nuts with red oxide primer including fitting bottom runner and cleat etc. for fixing ceiling joist as per design complete as directed as per specifications. b) Using other ISI marked approved brand tube

Providing Pre Painted Galvanized Iron Sheet Roofing (PPGI) at all levels including fitting and fixing with self drilling, self tapping screws complete. (Roof trusses, purlins etc. to be measured and paid separately.) TATA Blue scope/ Dyna roof / Durakolor /Wonder Roof or equivalent as directed by the Departement (iii) 0.50 mm thick

1Nos. of Stainless Steel (304 grade ) Rose Gold sign board of height 2.5 ft.(30 Inches) Complete as per drawing and desing and as specified by Eng. In charge . 1x5 letter =5 letter

a) Supply, fitting and fixing

b) Transportation and Installation

Outer Development (Internal road and Parking Shed)

Earth work in excavation for foundation trenches of walls retaining walls, footings of column, steps, septic tank etc. including refilling the quantity as necessary after ……………….. removal of surplus earth with all lead and lifts as directed and specified. (A) Up to a depth of 2.00 m below the existing ground level. (b) In hard soil.

Surface dressing of ground including removing vegitation and/ or undulation of ground not exceeding 150mm deep and disposal of rubbish outside the periphery and lift up to 1800mm in all kinds of soil.

B) By mix place method ( Construction of granular sub-base by providing close graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per cl. 401 (with an initial lead of 5Km.) (Including cost of testing of materials at site and laboratory as directed by the deptt.) i) For grading-I material.

Water bound macadam (Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with vibratory roller 8-10 tonnes in stages to proper grade and camber, applying and brooming requisite type of screening/binding material to fillup the interstices of coarse aggregate, watering and compacting to the reqd. density (with initial lead of 5.0Km). A) By manual means b) Using screening Type-A (13.2mm Agg.)

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately). (a) In prop 1:3:6 aggregate by volume.

Providing SUN ROCK CTS/DEVI paver block/ tiles of concrete grade M30 or above of approved quality, size, shape of specified thickness over a leveling, bedding layer of 30mm compacted sand over a base course of WBM or PCC (Base course to be paid seperately) including cutting where necessary finished with spreading, sweeping jointing sand and compacting the pavers using vibrating compactor as specified and directed. a) 80 mm thick

Providing, fitting, hoisting and fixing of roof trusses fabricated out of combination of any two or all of the following sections (i) Square section (ii) Rectangular Hollow section of specification RSH/SHS and (iii) M.S. circular hlollow section of Grade 210 including purlins, bottom runners and providing M.S. cleat, M.S. angle base plank, bolts and nuts with red oxide primer including fitting bottom runner and cleat etc. for fixing ceiling joist as per design complete as directed as per specifications. b) Using other ISI marked approved brand tube. (Use square hollow section of size 25mm×25mm and wall thickness of 2.6mm)

Providing Pre Painted Galvanized Iron Sheet Roofing (PPGI) at all levels including fitting and fixing with self drilling, self tapping screws complete. (Roof trusses, purlins etc. to be measured and paid separately.) TATA Blue scope/ Dyna roof / Durakolor /Wonder Roof or equivalent as directed by the Departement. (iii) 0.50 mm thick.

Construction of boundary wall

Earth work in excavation for foundation trenches of walls retaining walls, footings of column, steps, septic tank etc. including refilling the quantity as necessary after ……………….. removal of surplus earth with all lead and lifts as directed and specified. (A) Up to a depth of 1.00 m below the existing ground level. (b) In hard soil.

Providing brick soling in foundation and under floor with stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete. (a) Brick on flat soling.

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately). (a) In prop 1:3:6 aggregate by volume.

Supplying, fitting and fixing in position reinforcement bars conforming to relevant IS code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes ………………and placing in position with proper blocks, supports, chairs, spacers etc. complete. (up to 1st floor level). (b) Other ISI approved TMT reinforcement bar (SRMB/SAI/BISCON/Xtech) (For Assam Type Bldg., drain works,,retaining wall&boundary wall etc. . (i) TATA/SAIL

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0 M and removal of the same for in-situ reinforced concrete and plain concrete work in:

(i)Using 25mm thick plank(Raft)

(i)Using 25mm thick plank(Tie Beam)

(i)Using 25mm thick plank(Coloumn)

(i)Using 25mm thick plank(Top Beam)

Providing and laying Plain/Reinforced cement concrete works in prop 1:2:4 including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete works (shuttering where necessary shall be measured and paid separately). (I) Using mixture machine. (A) In sub structure up to plinth level. Foundation, footing, columns with base tie and plinth beam, pile cap, base, base slab…………. Not less than 100mm thick up to plinth level. (a) M15 or Prop 1:2:4

1st class brick nogged wall in cement mortar including racking out joints and curing complete as directed in super structure above plinth up to 1st floor level (protruding M.S rod/Tor steel of column to be embeded in cement mortar and will be measured and paid separately) (A) 112mm thick brick wall (a) In cement mortar in prop. 1:4

15mm thick cement plaster in single coat on rough side of single or half brick wall for interior plastering up to Ist floor level including arises, internal rounded angles, not exceeding 80mm in girth and finished even and smooth including curing complete as directed. (A) On Rough side (b) In proportion 1:4

Supplying fitting and fixing M.S.angles, M.S. flat, M.S. bolts and nuts including painting with red lead paint one coat complete as directed. a) M. S. Angles…… (50x50x5)

Providing & fixing concertina coil fencing with required dia 610mm (having 15 nos round per 6 meter length) up to 3.00m height of wall with existing angle iron Y shaped placed 2.4m or 3.00m apart and 9 horizontal RBT (Reinforced Barbed …………………………..wire of high tensile strength of 165 kg/sq.m with tape (0.52mm thicks and weight 43.478 8m/meter (cost of M.S angle, C.C. blocks shall be paid separately).

a) Applying one coat of cement primer of approved brand and manufacture on new wall surface after throughly brooming the surfaces free from mortar droppings and other foreign matter and including preparing the surface even and sand papered smooth.

Applying one self-priming coat of acrylic emulsion coating of Unicem "Rakshak" brand by thinning 1ltrs of paints with 1ltrs of water over freshly plastered wall surface after throughly brooming the surfaces free from mortar droppings and other foreign matter and including preparing the surface even and sand papered smooth as specified and directed by the department. b) Unichem rakchak

Painting two coats (excluding priming coat) on new steel and other metal surface with alluminium paint of approved brand and manufacture(Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) and brushing to give an even shade including cleaning the surface of all dirt, dust and other foreign matter. (i) Surfaces over 100mm in width or girth.

Sanitary and Water Supply

Supplying fixing PVC pipes of 6 kg/m2 9Supreme/Prince) or other I.S.I approved……. (a) In exposed or in trenches. (ii) 110 mm dia..

Supplying fitting & fixing 87.5 degree PVC bend of supreme/panel or other I.S.I approved. (a) In exposed or in trenches. (ii) 110 mm dia…..

Supplying fiting and fixing 87.5 degree PVC bend with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. (a) In exposed or in trenches. (ii) 110 mm dia…..

Supplying fiting and fixing 45degree PVC bend of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. (a) In exposed or in trenches. (ii) 110 mm dia…..

Supplying fiting and fixing PVC Plain single tee of (Supreme/ Prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. (a) In exposed or in trenches. (ii) 110 mm dia…..

Supplying fiting and fixing PVC single tee with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. (a) In exposed or in trenches. (ii) 110 mm dia…..

Supplying fiting and fixing PVC socket plug of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. in exposed surface or trences as necessary complete at all levels including below G.L. as directed and specified. (a) In exposed or in trenches. (ii) 110 mm dia…..

Providing fitting & fixing PVC cowel of I.S.I make… (iv) 75 mm dia P.V.C cowel……..

Supply fitting and fixing pipes with all necessary fitting in exposed or in trenches including trenching and refilling the same etc. Complete as directed (B) uPVC with uPVC fitting( Using uPVC high pressure pipe) (Using Supreme/Prince.....) (v) 40 mm dia…..

Supplying fitting & fixing Cpvc pipecfor hot & cold water…………………..at all level as directed & specified (ii) Concealed by chiselling or breaking brick wall/C.C/R.C.C and making good to damages

Supplying and fitting CPVC BALL VALVE as specified and directed. a) 50mm dia

25 mm dai

50 mm dia.

Providing fitting and fixing vitreous china pedestal type water closet (European type W.C pan 400mm high ) with seat and lead ,CP brass hinges and rubber buffers , CI/MS brackets , 40 mm dia flush band with fittings including painting of fittings and brackets, required. (Flushing Cistern to be paid separately) A) parryware make a)White iii) Universal.... closet P Trap (Cat No C0272)(Inclusive of seat cover)

Supplying, fiting and fixing PVC flushing cistern with all internal fittings with CI brackets including fitting and fixing standard size CP flush pipe, union clamps etc. compete as directed and specified (pipes will be measured separately A) parryware make a)White i) Economy Single flush .......(Cat No C8090/C8055)

Providing fitting and fixing vitreous china flat back type lipped front urinal basin with standard flush pipe and CP brass spreader and brass unions, etc. complete including painting of fittings and brackets, cutting and making good the walls & Floors wherever required. (A) Parryware Make (a) White (i) New Magnum (Cat. No. C0575)

Supplying fiting and fixing vitreous china division plate including fitting and fixing compete as directed and specified. (A) Parryware Make (a) White (i)Partion Magnum/Large (Cat. No. C0571/07)

Providing fitting & fixing stainless steel kitchen sink of Parryware make with CI/MS brackets, C.P. brass chain with rubber plug, PVC waste pipe etc. complete including painting the fittings ,cutting &making good the walls wherever required. (Sink cock, stop cocks, waste coupling are to be paid separately (B) Nirali (viii) 355 x 355……….

Wall Hang Basin Providing vitreous China wash basin with CI/MS brackets, C.P brass chain with plug,PVC waste pipe including painting of fittings and brackets, cutting and making good the walls wherever required. (Pillar cock, stop cocks, waste coupling are to be paid separately) b) Hindware a) White ii) Corel 520 Dia. (Cat. No10097)

Table Top Basin Providing vitreous China wash basin with CI/MS brackets, C.P brass chain with plug,PVC waste pipe including painting of fittings and brackets, cutting and making good the walls wherever required. (Pillar cock, stop cocks, waste coupling are to be paid separately) b) Hindware a) White ii) Corel 520 Dia. (Cat. No10067)

Supplying fitting and fixing C.P. bib cock 15mm dia of approved brand directed and specified. (G.I. & C.P pipes will be measured separately) v) Crabtree Frattini brand ( For V.I.P. use) (C.P.) b) Florence Beauty ………………. ii) C.P. 2-way bibcock double handle with flange Cat No.21017

Supplying and fitting fixing C.P. pillar cock of 15mm dia of approved brand as specified and directed. iv) Crabtree Frattini b) Florence Beauty i) pillar cock Cat no 21001

Providing fitting & fixing decorative mirror complete as directed .. (b) Size 600 x 450 mm………..

Providing, fitting and fixing Liquid soap dispenser and liquid soap container complete as directed and specified. (i) Jaquar Make(a) Continental (Cat.No.ACN-1135N) (with glass bottle)

Providing fixing C.P towel rail complete as directed.. (a)Jaquar make (ii) Continental 600 mm…………………

Supplying and placing plastic cylindrical vertical claused top (PCVC) tank of Sintex / Polycon / Patton make over the stagging with manhole cover with locking and cleaning arrangement including providing pads of size as required for inlet and outlet pipes (i) 2000 liters capacity, (a) Sintex make

Supplying ,fitting and fixing of health faucet with 8 mm dia 1.2 meter long flexible tube & wall hook.(Jaquar make)

Septic Tank

Earth work in excavation for foundation trenches of walls retaining walls, footings of column, steps, septic tank etc. including refilling the quantity as necessary after ……………….. removal of surplus earth with all lead and lifts as directed and specified. (A) Up to a depth of 1.00 m below the existing ground level. (b) In hard soil.

Providing brick soling in foundation and under floor with stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete. (a) Brick on flat soling.

Providing and laying plain/reinforced cement croncrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately) I) Using Mixer Machine A)In substructure up to plinth level Foundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level. N) Without using admixture, plasticiser I) M15 grade concrete or Prop. 1:2:4

Brick work in cement morter with 1st class brick including racking out joints and dewatering if necessary, and curing complete as directed in sub-structure up to plinth level. (b) In proportion 1:4.

Providing precast R.C.C slab over drain ,septic tank etc. in prop. 1:2:4 reinforced with 10mm M.S. bar @ 150mm centre both ways tying with 20 gauge black annealed wire with necessary shuttering , curing etc. complete including fixing in position as directed. a) 100 mm thick slab

Cement plaster skirting with cement mortar in prop. 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement including rounding of junctions with floor. (a) 15 mm thick

Supplying, fitting and fixing PVC pipes of 6 Kg/cm2 (Supreme/Prince) or other ISI approved including joining ,fitting and fixing wiyh clamps etc.as necessary complete at all levels including below G.L as directed and specified.

a) In exposed surfaces or in trenches (ii)110 mm dia

a) In exposed surfaces or in trenches (ii)75 mm dia

Supplying fiting and fixing 87.5 degree PVC bend with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches.

Supplying fiting and fixing PVC reducer of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. (iv)110mmx75mm

Providing fitting and fixing PVC cowel of ISI make complete as directed and specified. (iv)75 mm dia PVC cowel of ISI make

Construction of filter bed in soak pit including earth work in excavation of soil and then filling up of the trench with brick bats/Charcoal covered with earth over a layer of A.C. plain sheet above brick bat filling complete as directed. (sizes of soak pit may vary depending on the sizes and capacities of the septic tank as well as the number of users as mentioned in the table.

Construction of inspection pit inside measurement 450mm x450mm x450mm flush with 100mm diameter HCI/PVC pipes and cement concrete base in proportion 1:3:6 over flat brick soling, 12cm brick wall in cement mortar in proportion 1:4 finished with 13mm cement plaster in proportion 1:2 in side wall and floor. 450mm x450mm air tight C.I. inspection pit cover and frame complete including supplying of materials, necessary excavation of pit as directed.

Electrical Works

Supply and laying of following size PVC/XLPE insulated and PVC sheathed 1.1 KV G Solid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, Armour (Aluminium for single core up to 70 sq mm balance Aluminium strip, Galvanised for cables up to 2x10 sq mm.3x10 sq mm,4x6 sq mm balance all galvanised steel strip) , extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1) 1988 armoured U.G. cable U.G. cable laid in ground/partially in air (as required for termination over ground including excavation of cable trench up to depth of 75cm, refilling, protective brick covering, Sand cushioning etc complete handling of surplus spoil, debris et to proper place as specified and directed by the deptt. (Nicco/ Havells/ RPG/CCI/Polycab/Gloster/ Finolex make) . 321.2.3 10.00 Sq.mm 3 Core armoured U.G. cable

Supplying with fitting and fixing MCCB income and MCB outgoing sheet steel, phosphatised, powder painted single door surface mounting vertical TPN MCB DB incorporated with bas-bar, Neutral link, Earth bar up to 125A and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved, specified and directed by the deptt. 15.21.1.2. 8 way TPN (4+24) single door

Supplying with fitting and fixing sheet steel, phosphatised, powder painted dust & vermin proof Double door IP-43 double door surface mounting vertical TPN MCB DB incorporated with bas-bar 125A, Neutral link, Earth bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved, specified and directed by the deptt. 15.20.1.2. 8 way TPN (8+24) double door

Supplying with fitting and fixing sheet steel, phosphatised, powder painted Single door surface mounting MCB DB incorporated with bas-bar, Neutral link, Earth bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved, specified and directed by the deptt. 15.1.1. ABB, Schneider MG, legrand, Hager make 15.1.1.1. 4 way SPN single door

Supplying with fitting and fixing panel mounting open execution 25 KA 415V 50Hz 3P MCCB (Ics=Icu, adjustable Ir setting 0.7) without enclosure of the following capacity complete with making necessary connection as approved by the Deptt. as specified and directed by the deptt. 16.13.1.) 25 KA 415V 50 Hz 3P MCCB (Schneider, legrand, Siemens make) 16.13.1.4.) 63A

Supplying with fitting and fixing TPN 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. 16.5.1. B Series (ABB, Schneider MG, legrand, Hager make) 16.13.1.4.) 63A

Supplying with fitting and fixing single Pole 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. 16.1.1.)B Series (Schneider MG, legrand, Hager make) 16.1.1.1.) 6 to 32A

Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) including earth continuity in surface/ recessed 20 mm. dia. 2mm thick/ heavy ISI marked IS: 9537 PART - III rigid PVC conduit wiring system. With 2 x 4 sq. mm. + earth continuity with 1x2.5 sq. mm. cable in 20 mm. dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit.

Wiring for light/fan/call bell point with 2x1.5 sq. mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) in surface/ recessed conduit wiring system with 20mm dia 2mm thick / heavy rigid PVC IS: 9537 Part - III conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) including 6 Amp flush type switch/ bell push (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.) GI/ MS switch board (ISI marked) with phenolic laminated sheet cover ,ceiling rose (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.) etc. complete

2.1.1.) Short point up to 3.00 metre. length.(gf to 2nd floor)

2.1.2.) Medium point up to 6.00 metre. Length..(gf to 2nd floor)

Wiring to 5 a pin 6 Amps plug point with 1.5 sq. mm P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) in surface/ recessed 2 mm thick/ heavy rigid ISI marked IS: 9537 PART - III rigid PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) wiring system including 5 pin 6 Amps flush type plug socket and 6 Amps F/T switch (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.), GI/ MS switch board (I.S.I. mark with phenolic laminated sheet cover including earth continuity with 1.5 sq. mm. cable to third pin of the plug socket etc. as required complete, when placed elsewhere. 1.2.1.) Short point up to 3.00 metre. length.

Wiring for 5/6 pin 16 Amps power plug point with 4 sq. mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) in surface/ recessed conduit wiring system including and fixing 5/6 pin 16 Amps flush type socket outlets and 16 Amps flush type switch ( Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.), GI/ MS switch board (I.S.I. mark with phenolic laminated sheet cover earth continuity with 2.5 sq. mm cable to the 3rd pin of the socket as required complete with 20 mm. dia. 2mm thick/ heavy ISI marked IS: 9537 PART - III rigid PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) 1.3.3.) Long point up to 10.00 metre. Length.

Supplying including fitting fixing of following A.C. Ceiling fan complete with all accessories like down rod, canopy etc. of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department [Without regulator]. 27.1.2.) Premium model 1200 mm Sweep (ORIENT PSPO make) / Premium model 1050 / 1200 mm Sweep SS-390 Deco Havells make)

Supplying including fitting fixing of following A.C. Exhaust fan in the existing hole on the wall of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department. 27.2.1.2.) Power Flow 225 mm sweep (ORIENT make)

Supplying fitting and fixing of ceiling fan regulator including connections etc complete as required. 27.6.2) electronic type

Supplying and fixing of Call bell (Buzzer) including 6 amp capacity flush type bell push switch including connection as approved by the Deptt.)as required.

Supply installation, testing of G.I earth station with perforated 40 mm dia and 4.5 m long heavy duty G.I pipe….directed..

Extra for using salt 5K and charcoal 64K in pipe earth station pit to provide low impedance ground in location of high soil resistivity as when required and specified by the deptt.

1 HP single Phase Centrifugal monoblock pump set (Crompton Greaves/ Aquatic/ CRI/ V-Guard make) with DOL Starter ( Crompton Greaves/ Control & Switch Gear/ BCH/ L& T / Siemens make) .

Supplying with fitting & fixing of the following Street light luminaries complete with lamp in the existing pole including making necessary connection as approved by the Deptt.)with 2 ×1.50 sq.mm F.R. multistrand and P.V.C. insulated single core copper cable as specified and directed by the department. 25.1.1. Philips make) Type TRC033 2xTL-D36W IC For lamp 2xTL-D36W/TL-40W./ Wipro make) : WSF 15240 For lamp 2x36/40W FTL (T8) / Crompton Greaves make) SFE1624HSBN For lamp 2x36/40W FTL / Havells make): LHRF 14204011 For lamp 2x36/40W FTL

SARAIGHAT ENGINEERS