Repair to certain civil works to offrs md accn (RA line) at Mily station Kannur under AGE (I) Cannanore.

Amount

Demolition of brick or stone or PCC block masonry built in cement or cement lime mortar, including all quoins, arches, pillars etc. but excluding ashlar facings, dressed stone work and pre cast concrete articles and removing debris outside MD land all as directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) all as directed

M&L Reinforced cement concrete (1:1.5:3), type A1, (using 20mm graded stone aggregate) as in slabs supported on walls all as specified and directed.

M&L for use and waste of formwork to soffits of suspended slab, rough finished surfaces of concrete all as specified and directed.

M&L Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 5cm but n exc 10cm wide rough finished surface of concrete flat all as specified and directed.

S&F TMT bars 10 mm dia and over as in reinforcement, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips all as specified and directed.

All as per Sl item No 6 above, but 6 to 8mm dia bars as in stirrups, spacers and binders all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15cm thickness (below or above ground level) and removing debris outside MD land all as directed.

M&L for laterite stone masonry, regular coursed, well bonded and solidly hearted , built in CM (1:6) all as specified and directed.

Demolition of stone slab and tiles of any description and thickness in floors including cement mortar bedding (but not backing), and rubbish off the premises outside MD land and all as directed.

Taking down cement or cement lime plaster on brick/stone walls or in ceiling surfaces incl racking out joints hacking for key scrubbing down with water etc and removing rubbish outside MD land all as specified and directed.

M&L for rendering 15mm thick in cement mortar (1:6) on stone masonry surfaces, finished even and smooth without using extra cement all as specified and directed .

M&L for rendering 15mm thick in cement mortar (1:4) on stone masonry surfaces, finished even and smooth without using extra cement all as specified and directed .

M&L for rendering 5mm thick in cement mortar (1:3) on concrete ceiling surfaces, finished even and smooth without using extra cement all as specified and directed .

M&L for rendering 15mm thick in cement mortar (1:4) on other than fair faces of brick work or concrete surfaces including chajja, facia etc surfaces, finished even and smooth without using extra cement all as specified and directed .

Taking out and cleaning of existing roof treatment of any description by wire brushing and cleaning top surface with water and remove the rubbish to outside MD land etc. and brushing with neat cement slurry at 3 Kg per sqm on concrete surfaces. M& L for water proofing treatment to RCC roof with APP modified prefabricated five layer membrane of 4mm thick and weight not less than 4.00 Kg per Sqm reinforced with non woven polyster matt reinforcement 160g/sqm (weighing not less than 160gms/sqm) having softening point not less than 140 degree centigrade, longitudinal tensile strength not less than 800N/Sqcm tearing strength of 180Nm by torch application over a solvent based bitumen primer, Shalitex primer @ 0.20 Kg per Sqm of same manufacturere conf to IS 3384-1986. Membrane shall be laid including minimum 7.5cm side overlap and 10cm end lap. All cracks in roof shall be filled with cement putty using suitable bonding agent (Shalocrete 42) before laying cement plaster all as specified and directed.

M&L for 25mm thick plain cement concrete (1:2:4), type B0, using 12.5mm graded stone aggregate as in roof padding to achieve required slope and thickness, finished even and smooth without using extra cement mixed with water proofing compound all as specified and directed. Note Water proofing compound shall be measured and paid seperately.

Supply only Water proofing compound

S&F Doctor fixit pidifin 2k high performance 2 component flexible providing and laying water proofing treatment to sunken portion of WC,bathroom etc by applying cement slurry mixed with two components elasomeric acrylic based polymer modified cementitious composited compound coating of make Dr Fixit, pidilite or equivalant as follows :- (a) Applying Ist layer of cement @ 0.488 kg/sqm mixed with acrylic based polymer modified cementitious composited compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours (b) Second layer of slurry of cement @0.242 kg/sqm mixed with acrylic based polymer modified cementitious composited compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours (c) Providing 20mm thick cement screed 1:4 mixed with water proofing liquid as per manufacturer instructions complete all as specified and directed. Note : Cost of Water proofing liquid should be included in the rate.

M & L for plain cement concrete (1:5:10),type E2 using 40mm graded trap stone aggregate as in foundation, filling including necessary form work all as specified and directed

M&L 25mm thick PCC 1:2:4, Type B0 (using 12.5mm graded stone aggregate) as in flooring all as specified and directed.

M&L for coloured joint free non-skid ceramic tiles, 7 to 8mm thick, area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured / white cement to match laid over and including 20mm thick screed bed or bedding layer in cement mortar (1:6) all as specified and directed.

M&L for coloured glazed ceramic tiles 200X300X7mm or 250x350x7mm, as in skirting / dado, set and jointed in neat cement slurry and pointed in coloured / white cement to match laid over and including 10 mm thick backing on stone/brick masonry surfaces in cement mortar (1:4) all as specified and directed.

M&L for vitrified light shade ceramic tiles, 10mm thick, area of each tile exceeding 0.36 Sqm but not exceeding 0.42 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured / white cement to match laid over and including 20mm thick screed bed or bedding layer in cement mortar (1:6) all as specified and directed.

S&F in repairs Vitreous China squatting pan “Orissa” pattern, of size 580 x 440 mm white, with integral foot rests, (excluding flushing cistern and flush pipe), including provision of lime concrete bedding, connection to trap and to flushing pipe, anti-syphonage pipe, etc and joint between flushing pipe and socket of WC pan, complete and making good to the floor all as specified and directed.

S&F Vitreous China Wash down water closet pan (Pedestal pattern) white, (excluding flushing cistern and flush type) pedestal pan and trap including connection to drain (or outgoing pipe) and to flushing pipe, anti syphonage pipe, etc complete including plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminized hinging device as fixed in repairs all as specified and directed.

S&F in repairs PVC valveless, syphonic action type flushing cistern low level, 10 Litre capacity, white, with inlet, ball valve, float and handle including low or high density PVC flush pipe all as specified and directed.

S&F in repairs health faucet , brass chromium plated jet spray including LDPE flexible cable with jet of 100 mm long fixing to 15 mm dia pipe all as specified and directed.

S&F 1000 litres capacity rotational moulded polthylene water storage tanks (cylindrical vertical with closed top) of make Sintex/Polycon/Plasto hoisted and fixed in position including taking down unserviceable water tank all as specified in SSR Part I,2009 and directed.

S&F ball brass valves, high pressure, with polyethylene float and fly nut complete, screwed for iron pipe or brass ferrule of 20mm bore dia all as specified and directed.

S&F in repairs ball brass valves, high pressure, with polyethylene float and fly nut complete, screwed for iron pipe or brass ferrule of 20mm bore dia all as specified and directed.

Taking up or down steel tubing and connections including cleaning for removing to store of sizes upto 20mm bore all as directed.

Taking up or down LDPE pipes of any description of 32mm bore all as directed.

Dismantling and breaking up drain pipes 75/100mm bore (cast iron) set in cement mortar any dia of pipes and removing debris outside MD land

M&L PVC (SWR) pipe type 'B' 75mm bore single socketed with rubber ring joints laid in trenches or in floors all as specified and directed.

M&L PVC (SWR) pipe type 'B' 75mm bore single socketed with rubber ring joints fixed to wall all as specified and directed.

M&L PVC (SWR) pipe type 'B' 110mm bore single socketed with rubber ring joints laid in trenches or in floors all as specified and directed.

M&L PVC (SWR) pipe type 'B' 110mm bore single socketed with rubber ring joints fixed to wall all as specified and directed.

M&L PVC (SWR) vent cowl 75mm dia with solvent cement joints all as specified and directed.

S&F 75 mm bore, PVC (SWR) bends all as specified and directed

S&F 110 mm bore, PVC (SWR) bends all as specified and directed

S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement all as specified and directed.

M&L for 75mm diameter PVC (SWR) floor trap, plain with grating including jointing with solvent cement all as specified and directed.

Cutting chases for concealing water tubing and making good, in stone or concrete block or slab or walls, cutting not exc 10cm girth complete all as specified and as directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel ( ½ round or ¾ section) in cement concrete 1:2:4, type B1 using 20mm graded stone aggregate, smooth finished and reforming benching as required for internal dia of pipe 160mm ball as directed.

S&F grating square 150mm size of PTMT complete all as specified and as directed.

S&F for 15 mm bore UPVC pipes of pressure rating 10 kgf / cm2, fixed complete to walls, ceilings etc. all as specified and directed.

S&F for 20 mm bore UPVC pipes of pressure rating 10 kgf / cm2, fixed complete to walls, ceilings etc. all as specified and directed.

S&F in repair Vitreous China Wash basin, white, flat back, size 630 x 450 mm, including CI brackets, (but excl. pillar tap) cutting for and pinning in ends of brackets or erecting stand etc complete all as specified and directed.

S&F Stainless steel sinks 1mm thick with plugs, washers and waste; including bedding in cement mortar on to dwarf walls, or including fixing cantilever brackets and connecting union to waste pipe, overall size 495mm x 420mm, bowl size 410 x 330 x 160mm etc complete all as specified and directed.

S&F in repairs 32mm Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed all as specified and directed.

S&F in repairs 15mm pillar taps, cast copper alloy with capstan heads, chromium plated , screwed down high pressure ,with or without lettered hot or cold with long screwed shanks and fly nuts screwed for iron pipe and fixed all as specified and directed.

Supply and fix PVC connecton 45cm long with PTMT nuts for flush tank, wash basin, etc. all as specified and directed

S&F in repairs bib tap 15mm dia, chromium plated, fancy type, cast copper alloy, screwed down, screwed for iron pipe or ferrule and complete all as directed.

S&F in repairs stop cock 15mm bore cast copper alloy, chromium plated, fancy type, screwed both ends for iron pipe or for unions and screwed down, high pressure with long shank & cup complete all as specified and directed

Taking down wooden door shutters of any description n exc 1 Sqm each all as directed.

Taking down wooden door shutters of any description exceeding 1 Sqm and not exceeding 2 Sqm each all as directed.

Taking down door shutters of any description exceeding 1 Sqm and not exceeding 2 Sqm each and refixing the same opening after easing and adjusting and refixing/renewal of builders hardware with screws all as directed.

M&L for mild steel flat iron of size 25 x 3mm for holdfasts for securing new wooden frames and similar articles conforming to Fe-290 Gde-E-165 all as specified and directed.

M&L for PCC 1:2:4, type B1 using 20mm graded stone aggregate for fixing hold fast including necessary form works all as specified and directed.

M&L for second class hardwood, plain, solid straight chowkats & frames wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joints all as specified and directed.

S&F 30mm thick second class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc; (with out sash bars), edges of framing, fitted with cut and mitered beads for securing glass, etc sizes of members of shutters as specified in SSR Part-I, Section 8, Clause 8.24 (a) all as specified and directed.

M&L for second class hardwood, panelled shutter 35mm thick (any number of panel) with lock rail and panel of 9mm BWP, 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated all as specified and directed.

S&F mild steel framed work such as grills gratings, etc, with ends of bars shouldered and / or riveted, or forged into spikes; framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, frame work of water tanks and similar work conforming to Fe-290 Gde E-165 all as specified and directed.

M&L in repair 18/19mm thick block board , grade I quality, exterior grade decorative type with decorative face veneer on one faces complete all as specified and directed.

S&F mild steel Continuous (piano) hinges, , bright finish or electrogalvanised with width of flaps (When open) 30 mm fixed with screws to timber frame work complete all as specified and directed by Engineer-in-Charge

Hacking out old broken glass (any thickness, size, quality or description) n exc 1.5 sqm from wooden or metal frames including beads all as directed.

S&F 3mm thick plain sheet glass, ordinary quality and glazing with oil putty in squares not exc 0.50 Sqm in each pane all as specified and directed.

S&F 3mm thick figured glass, ordinary quality and glazing with oil putty in squares not exc 0.50 Sqm in each pane all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples all as specified and directed.

S&F for second class hard wood, plain fillets, square, rectangular or triangular in section, clean sawn, sectional area n. exc. 3 sqcm secured with nails or brads all as specified and directed.

S&F stainless steel butt hinges medium weight; 100mm size as per IS 21817 fixed with stainless steel screws all as specified.

S&F stainless steel butt hinges medium weight; 75mm size as per IS 21817 fixed with stainless steel screws all as specified.

S&F 100mm long aluminum anodized barrel tower bolts of extruded section fixed with stainless steel screws all as specified.

S&F 200mm long aluminum anodized barrel tower bolts of extruded section fixed with stainless steel screws all as specified.

S&F aluminium anodised sliding door bolts 300mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and directed

S&F extruded aluminum alloy anodized handle fabricated type 100mm size all as specified.

S&F extruded aluminum alloy anodized handle fabricated type 150mm size all as specified.

M&L preparing new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel painting over a coat of pink primer all as specified and directed.

M&L for preparation of new or old untreated steel surfaces of any description not other wise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified & directed.

M&L preparing old treated wooden surfaces of any description over 10 cm width or girth and applying a coat of synthetic enamel painting all as specified and directed.

M&L preparing old treated steel surfaces of any description over 10 cm width or girth and applying a coat of synthetic enamel painting all as specified and directed.

M&L solid PVC door frame of sizes 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, all as specified and directed.

S&F factory made solid PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain coloured PVC “C” channel having a PVC sheet strip of 20mm width stock inside with solvent cement for stiles and plain colour PVC sheet for top rails, lock rails and bottom rails on either side and as gap insert for top rail & bottom rail on either side and as gap insert for top rail and bottom rail, paneling of plain colour of PVC sheet fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement etc. Details as peer specification and drawings and all as directed.

M & L for 75 mm thick plain cement concrete 1:3:6, type C2 using 40mm graded aggregate as in plinth protection etc including necessary form work complete all as specified and directed

M & L for plain cement concrete 1:3:6, type C1 using 20mm graded aggregate as in surface channel and drain etc including necessary form work complete all as specified and directed

M & L for preparation of newly plastered surfaces of wall and applying 1mm thick acrylic wall care putty and making the surface smooth and even including sanding each layer to receive next new layer, one coat of wall primer and applying two coats of oil emulsion distemper and all as specified and as directed.

M&L for preparation of new plastered ceiling surfaces and applying three coats of white wash all as specified and directed.

M&L for preparation of new plastered surfaces and applying three coats of white wash on walls surfaces all as specified and directed.

M&L preparation of new plastered surfaces of wall and applying two coats of cement base paint over a coat of primer all as specified and as directed.

JESWIN BUILDERS

RS ENTERPRISES

KDR CONSTRUCTION