Construction of Taluka Library Building at Nakhatrana Dist. Kutch.

NAME OF WORK : Construction of Taluka Library Building at Nakhatrana Dist. Kutch.

Sr. Quantities Item of Work Estimated Unit Total

In Rupees In Words

Clearing and grubbing road land including uprooting rank vegetation grass

Rupees TwentyEight

bushes,shrubs,sapling and trees girth up to 300 mm removal of stumps of trees cut earlier and

1 0.35 28455.09 Thousand Four Hundred Hec

disposal of unserviceable materials (C) By mechanical means in area of light jungle

FiftyFive Paise Nine Only

Providing corrugated G.I. sheet of class-3 roofing fixed with glavanished iron J or L Hooks, Bolts

Rupees Seven Hundred

and nuts 8mm diameter with bitumen and G.I. limpet washer or G.I. limpet washer. filled with

2 110.00 734.19 ThirtyFour Paise Nineteen Sqm

white lead complete excluding the cost of purlins, Rafters and Trusses.(1) 0.80 mm thick sheet.

Excavation for foundation upto 1.5 m depth including sorting out and stacking of useful Rupees One Hundred

3 1707.90 materials and disposing off the excavated stuff upto 50 Meter lead.(A) Loose or soft 122.94 TwentyTwo Paise NinetyFour Cum

Excavation for foundation for depth from 1.5 m to 3.0 m including sorting out and stacking of

Rupees One Hundred Seventy

4 720.98 useful materials and disposing off the excavated stuff upto 50 Meter lead.(B) Dense or Hard soil 170.69 Cum

Paise SixtyNine Only

Filling available excavated earth (excluding rock) in trenches. plinth, sides of foundations etc. In Rupees One Hundred

5 1674.91 layers not exceeding 20 cm. in depth consolidating each disposited layer by ramming and 136.92 ThirtySix Paise NinetyTwo Cum

Filling in foundation and plinth with murrum or selected soil in layers of 20cm. thickness Rupees Two Hundred

6 3008.12 including watering, ramming and consolidating etc. complete. 269.75 SixtyNine Paise SeventyFive Cum

Filling in plinth with sand under floors including watering ramming, consolidating and dressing

Rupees Four Hundred

7 39.83 complete 481.8 Cum

EightyOne Paise Eighty Only

Applying general insecticide pest control treatment to floors, cupboards etc including labour

materials etc. complete. Using Imidacloprid 30.5 SCas Per IS 6313 part -II( (0.075%

Rupees NinetyOne Paise

8 386.35 concentration by mass) is recommended 10.5ml chemical diluted with 5 liters of water 91.63 Sqm

SixtyThree Only

application 0.5 litre chemical /Sqm of surface is recommended as per I.S.

P.C.C : Providing and laying cement concrete 1:2:4 (1-Cement : 2- Coarse sand : 4- graded stone Rupees Three Thousand Nine

9 360.86 aggregates 20 mm nominal size) and curing complete including cost of formwork in (A) 3910.99 Hundred Ten Paise Cum

Foundation and Plinth NinetyNine Only

Providing and laying controlled cement concrete M.250 concrete With all lead, including all

transportation, pumping, pouring, curing of concrete etc complete including the cost of Rupees Five Thousand

10 259.70 formwork but excluding the cost of reinforcement for reinforced concrete work in M250 all RCC 5052.37 FiftyTwo Paise ThirtySeven Cum

element like foundation, Only

(A) Footing, at all floor level from below plinth and above plinth level

Providing and laying controlled cement concrete M.250 concrete With all lead, including all

transportation, pumping, pouring, curing of concrete etc complete including the cost of

Rupees Six Thousand Eight

11 10.00 formwork but excluding the cost of reinforcement for reinforced concrete work in M250 all RCC 6840.06 Cum

Hundred Fourty Paise Six Only

(B) Walls, from top of foundation level all floor level

Providing and laying controlled cement concrete M.250 concrete With all lead, including all

transportation, pumping, pouring, curing of concrete etc complete including the cost of Rupees Six Thousand Five

12 128.45 formwork but excluding the cost of reinforcement for reinforced concrete work in M250 all RCC 6584.84 Hundred EightyFour Paise Cum

element lik, © Slabs, landing, shelves, Balconies, Girders and Cantilever all floor level. EightyFour Only

Providing and laying controlled cement concrete M.250 concrete With all lead, including all

transportation, pumping, pouring, curing of concrete etc complete including the cost of Rupees Six Thousand Three

13 173.02 formwork but excluding the cost of reinforcement for reinforced concrete work in M250 all RCC 6326.49 Hundred TwentySix Paise Cum

element lik © Slabs, landing, shelves, Balconies, Lintels, Beams, Girders and Cantilever all floor FourtyNine Only

Providing and laying controlled cement concrete M.250 concrete With all lead, including all

transportation, pumping, pouring, curing of concrete etc complete including the cost of Rupees Seven Thousand

14 39.22 formwork but excluding the cost of reinforcement for reinforced concrete work in M250 all RCC 7342.52 Three Hundred FourtyTwo Cum

element lik © Landing, Stair case, Lintels, Copping, Beams, Girders, shelves,Balconies, and Paise FiftyTwo Only

Cantilever all floor level.

Providing and laying controlled cement concrete M.250 concrete With all lead, including all

transportation, pumping, pouring, curing of concrete etc complete including the cost of Rupees Five Thousand Nine

15 30.57 formwork but excluding the cost of reinforcement for reinforced concrete work in M250 all RCC 5982.51 Hundred EightyTwo Paise Cum

element lik (D) Columns, Pillars posts and struts, all floor level. FiftyOne Only

Providing and laying controlled cement concrete M.300 concrete With all lead, including all

transportation, pumping, pouring, curing of concrete etc complete including the cost of Rupees Six Thousand One

16 116.93 formwork but excluding the cost of reinforcement for reinforced concrete work in M300 all RCC 6141.1 Hundred FourtyOne Paise Ten Cum

element lik (D) Columns, Pillars posts and struts, all floor level. Only

GRADE SLAB (M200) : Providing and laying controlled cement concrete M.200 Concrete with all

Rupees Four Thousand Eight

lead, including all transportation, pumping, pouring, curing of concrete etc complete including

17 64.62 4829.77 Hundred TwentyNine Paise Cum

the cost of formwork but excluding the cost of reinforcement for reinforced concrete work in

SeventySeven Only

M200 Grade Slab

TRIMIX Road (M200) : Providing & Laying M200 grade controlled cement concrete without fly

ash trimix usinng P21 (water reducing concrete admixture at 100 ml per bag of cement & recon

3 s fiber at 125 gm per bag of cement including Cutting, Filling, Rolling, consolidating and

Shuttering of C channel required to maintain level, slope and thickness of the concrete road

leveling of placed concrete with surface vibrator and finishing with power floater & trowel light Rupees Six Thousand Three

18 115.10 brooming the surface & including Construction joints to be formed at every 5 mt distance by 6337.1 Hundred ThirtySeven Paise Cum

grooving with mechanical saw within 48 hrs. Groove/sawed joints shall be made of 5 mm width Ten Only

and depth min (1/3 rd depth of the pavement) as shown in the drawing and shall be filled with

ready to use PU sealant of UV gradecutting & filling of expansion joint as directed by Engineer in

Sr. Quantities Item of Work Estimated Unit Total

In Rupees In Words

Construction of granular sub-base by providing close graded Material conforming to

specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to

work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor Rupees Two Thousand Two

19 132.37 grader on prepared surface and compacting with vibratory power roller to achieve the desired 2299.7 Hundred NinetyNine Paise Cum

density, complete as per specifications and directions of Engineer-in-Charge. With material Seventy Only

conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR Value-30

Construction of granular sub-base by providing close graded Material conforming to

specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to

work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor Rupees Two Thousand Four

20 132.37 grader on prepared surface and compacting with vibratory power roller to achieve the desired 2416.05 Hundred Sixteen Paise Five Cum

density, complete as per specifications and directions of Engineer-in-Charge. With material Only

conforming to Grade-II (size range 53 mm to 0.075 mm ) having CBR Value-25

Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to

mm ) to wet mix macadam (WMM) specification including premixing the material with water at

Rupees Two Thousand Four

OMC in for all leads & lifts, laying in uniform layers with mechanical averfinisher in sub- base /

21 115.10 2407.33 Hundred Seven Paise Cum

base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne

ThirtyThree Only

capacity to achievethe desired density, complete as per specifications and directions of

Engineer-in-Charge.

Providing TMT Bar FE 500D reinforcement for R.C.C. work including bending, binding and Rupees SeventySeven Paise

placing in position complete. upto floor two level TwentyNine Only

Brick work using common burnt clay building bricks having crushing strength not less than 35 Rupees Four Thousand Two

23 97.64 kg./Sq.Cm. in foundation and plinth, in Cement Mortar 1:6 (1- Cement : 6 -fine sand) (B) 4214.33 Hundred Fourteen Paise Cum

Conventional ThirtyThree Only

Masonry work with aerated light weight concrete Blocks having crushing strength @

kg/sqcm Fixing with ready-mixed mortar ('Fixoblock'of M/s Ultratech cement Ltd./Rapid

Rupees Five Thousand One

Fix/Lion) having tensile adhision strength >0.8 N/mm2 and compressive strength of

24 433.81 5184.67 Hundred EightyFour Paise Cum

>2N/mm2.The mortar is to be fixed in a thickness of 3mm to 5mm on the clean and leveled

SixtySeven Only

surface of blockmasonry using proper trowel. For all floor and lead and lift For superstructure.

Providing 10mm thick cement plaster in single coat on brick/concrete walls for interior Rupees One Hundred

25 1238.25 plastering upto floor two level and finished even and smooth in (ii) Cement mortar 1:4 (1- 122.26 TwentyTwo Paise TwentySix Sqm

cement :4-sand)(For all floor) Only

Providing 20 mm thick double coat mala cement plaster on interior and external brick /

concrete work for plastering comprising of base coat of 12 mm thick cement plaster in cement Rupees Two Hundred

26 2944.38 mortar (1 Cement : 4 coarse sand) in rough finishing and 8 mm thick top coat of cement mortar 283.95 EightyThree Paise NinetyFive Sqm

1:2 (1 Cement : 2 Coarse sand) finished with trovel including all level, scaffolding, curing, tools, Only

tackles etc complete. ( For all floor )

Providing 15mm thick cement plaster in single coat on Rough (Similar)side of single or half brick

walls for interior plastering upto floor two level and finished even and smooth in (iii) Cement Rupees One Hundred

27 1208.35 mortar 1:6 (1-cement:6-sand) interior plastering above floor two level for every additional 141.48 FourtyOne Paise FourtyEight Sqm

storey height. all type of scaffolding , tools, tackles etc complete. (For all floor) Only

Providing and applying external finish of average 2 to 2.5mm thick acrylic polymer based

texture and pattern with standard tool and applicator as specified by manufacturer on exterior

surfaces at all heights including scaffolding to give even shades including thoroughly brushing

the surfaces free from mortar droping and other foreign matter and sand paper smoothed etc.

Rupees Three Hundred One

28 2061.07 complete as per the manufacture specifications and up to the satisfaction of Engineer in- 301.99 Sqm

Paise NinetyNine Only

charge/ Architect. The rate includes making of grooves, pattas and finishing as directed by

Architect/ Engineer in-charge. Paint shall be measured and paid in seperate tender item. (Item

should be executed by approved applicator only.)

Providing and fixing G.I. hexagonal chickenmesh of size 16 x24 of 22 gauge at junction of

concrete and brick work or between different materials after making "V" grove between two

different material surface and filled with rich cement mortar and @ 100mm on each side of Rupees Two Hundred

29 122.33 surfaces including necessary "U" nails / screws / washers with cleats for fixing, overlaps, 232.79 ThirtyTwo Paise SeventyNine Sqm

scaffolding at all floors / all levels / all heights / all shapes etc. complete as per drawing / Only

specifications and direction of Engineer-in-charge. For civil, plumbing, electrical & infrastructure

Providing and laying six courses water proofing treatment with bitumen felt over roofs

consisting of first, third and fifth course of blown bitumen 85/25 or 90/15 conforming to IS :

applied hot @ 1.45, 1.20 and 1.45 Kg per square metre of area respectively, second and fourth Rupees Six Hundred

30 383.80 courses of roofing felt type 3 grade I conforming to IS : 1322 (Hessian based self finished 681.75 EightyOne Paise SeventyFive Sqm

bitumen felt) , sixth and final course of stone grit 6 mm and down size or pea sized gravel Only

spread at 6 cubic decimeter per sqm including preparation of surface but excluding grading,

Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing

treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs,

podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc.,

prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for

vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal

surfaces and applying the same from negative (internal) side with the help of synthetic fiber

brush. The material shall meet the requirements as specified in ACI- 212-3R-2010 i.e by

Rupees Four Hundred Six

31 50.00 reducing permeability of concrete by more than 90% compared with control concrete as per 406.53 Sqm

Paise FiftyThree Only

DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry

shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out

all complete as per specification and the direction of the engineer-in-charge. The product

performance shall carry guarantee for 10 years against any leakage. For vertical surface two

coats @ 0.70 kg per sqm

Sr. Quantities Item of Work Estimated Unit Total

In Rupees In Words

Constructing Under Ground water tank with Providing and laying controlled cement concrete

M250 mix for R.C.C. work including reinforcement, boxing, centering, vibrating, curing and

mixed with approved water proofing cement compound or "CEMWET" or "PIDICRETE LW"

integral water proofing admixture as water proofing agent to be mixed with 50 kgs. bags shall

be as recommended by the manufacture of the water proofing material, concrete work for top,

bottom slab & side pardi, column, beam for under ground water tank item incl. 300mm Free

Board and Necessary excavation & refilling the available earth, raft thickness 250mm & wall

thickness 230mm, Sunctipn Pit size 600mmX600mmX600mm water proofing cement plaster Rupees Thirteen Paise

20mm thick Double Coat with smooth finishing & Glazes tile Dedo, vata 10cm X 10cm , 50mm FourtyFour Only

thick cement concrete flooring watering etc. Comp. to all face of tank. including locking

arrengement outlet, inlet, overflow and washout outlet pipe arrengement as necessary & C.I.

Cover 0.60 x 0.45 weight not less then 35 kg with locking arrengment.C.I. steps etc. comp as per

structural detail drawing Including thermo Mechanically treated bars (TMT BARS) Fe 500/500D

as directed by Eng-in-charge.

Providing erecting and fixing double coated ISI water tank of required capacity each with all Rupees Three Paise

necessary fittings and connection etc. complete on terrace NinetyFive Only

Providing and laying broken chine mosaic flooring for terrace using 12 mm to 20 mm

broken pieces of glazed tiles to be laid over cement mortar 1:3 to plain or slope and to be Rupees Seven Hundred

34 335.91 tempered to bring mortar creme out upto surface using white cement including rounding 779.7 SeventyNine Paise Seventy Sqm

off junctions and extending them upto 15 cm along the wall,clearing with water and oxalic acid Only

etc. as directed.

Water proof plaster : Providing 15 mm thick water proof cement plaster in single coat on brick/

block masonry or RCC wall, at all heights, finished even and smooth in CM 1:3 (1 cement :

sand) including providing and mixing water proofing materials of approved make in Rupees One Hundred

35 50.00 recommended proportions by manufacturer and as directed by Engineer-in-charge and finishing 188.69 EightyEight Paise SixtyNine Sqm

the surface wired finish to receive the tiles/ smooth finish with a floating coat of neat cement Only

slurry at 2.75 Kg/ sqm etc. complete at floor

Vitrified Flooring (Type - 01) : P & L 24" x 24" vitrified 8 mm thick tile flooring over 20mm

(average) base of cement mortar 1:6 ( 1 cement: 6 coarse sand) on new surface or fixing on Rupees One Thousand Four

36 88.82 existing flooring by adhesive material including dismentaling of existing flooring and jointed 1467.72 Hundred SixtySeven Paise Sqm

with color cement slurry including finised with flush pointing & cleaning the surface etc. SeventyTwo Only

complete for antiskit

Providing and laying white glazed tiles 6mm/8mm thick in skrting risers of steps and dedo on Rupees One Thousand Five

37 68.54 10mm thick cement plaster 1:3 (1-cement : 3-coarse sand) and jointed with white cement slurry 1592.4 Hundred NinetyTwo Paise Sqm

Tactile : Providing and applying Tactile Polyurethane (PU) Flooring system of approved shade

and design over the existing finished surface, including surface preparation, cleaning, grinding,

and removal of dust, oil, or loose particles. The system shall comprise application of primer

coat, base coat, and tactile PU topcoat with anti-slip finish to form tactile indicators (warning

and directional tiles) for visually impaired persons, as per approved pattern and sample.Work Rupees Two Thousand Seven

38 15.00 includes all necessary surface levelling, repairing of undulations, masking, layout marking, and 2787.6 Hundred EightySeven Paise Sqm

application using manufacturer’s recommended tools and techniques to achieve a seamless, Sixty Only

uniform, and durable tactile flooring.All materials shall be of approved make (e.g., Sika, Fosroc,

Asian Paints, or equivalent), and applied strictly as per manufacturer’s specification and

engineer-in-charge direction

Providing and laying polished Kota stone slab flooring over 20mm (Average) thick base of

cement mortar 1:6 (1-cement : 6-coarse sand) or L.M. 1.1.5 (1-Lime putty :1.5 - coarse sand) Rupees One Thousand

39 23.65 laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab 1013.87 Thirteen Paise EightySeven Sqm

including rubbing and polishing etc. complete. (A) 25mm thick Only

Providing and laying polished kota stone slab 25mm thick in risers of steps,skirting Dedo and

Rupees One Thousand One

pillars laid on 10mm thick cement mortar 1:3 (1- Cement : 3 coarse sand) and jointed with gray

40 2.93 1144.15 Hundred FourtyFour Paise Sqm

cement slury mixed with pigment to match the shade of slab including rubbing and polishing

Providing and laying Granite slab (16 to 18 mm thick) one side polished flooring over 20 mm

Rupees Two Thousand Three

(average) base of cement mortar 1:6 ( 1 cement : 6 coarse sand) or L.M. 1:1.5 laid and jointed

41 544.77 2348.61 Hundred FourtyEight Paise Sqm

with grey cement slurry including rubbing & polishing complete, for all floors.

Providing and laying 16 to18 mm thick polished Granite stone slab machine cut in single

piece in risers of steps, dedo, pillar, sill and jambs or dedo laid on 10 mm thick cement mortar

: 3 ( 1 cement : 3 coarse sand ) laid over and jointed withgrey cement slurry incl. rubbing Rupees Two Thousand Four

42 271.79 and polishing etc complete. The rate includes lodding, unlodding, scaffolding, wastage, making 2478.88 Hundred SeventyEight Paise Sqm

hole, cutting/ chasing, rounding champhering, edge polishing of edges. The work shall be EightyEight Only

carried out as per the approval of architect and engineer-in-charge. for all floors

Providing and fixing pre-cast Rubber Dye / steel Dye inter locking concrete block 60mm thick

with grade of concrete M300 pnumatic compressed / vibrated mechanically and as per

Rupees Seven Hundred Six

43 577.88 approved design Confirming to IS 15658 : 2006 including 35 mm Sand layer for levelling and 706.93 Sqm

Paise NinetyThree Only

filling the joint with sand in proper line and level as per guidlines of IRC : SP 63-2018 etc.

Kerb Stone : Providing and fixing pre-cast concrete kerb stone of gray cement based concrete

Rupees Three Hundred

block 30cm length,30cm height and 15cm thick of M250 grade concret as per approved design

44 269.95 374.92 SeventyFour Paise NinetyTwo Rmt

and including excavation for fixing in proper line and level,filling the joint with C:M 1:3

(1cement:3fine sand) etc complete.

Sr. Quantities Item of Work Estimated Unit Total

In Rupees In Words

Urinal partition : Providing & laying 16 to 18 mm thick both side mirror polished granite of

approved shade and quality, seleted and sorted for uniform color for urinal partition/ division

plate as per design and in required sizes and shapes after chasing /cutting of dado with cutter

machine fixing shall be carried out in white cement sand mortar (1:1) with matching pigment Rupees Two Thousand Six

45 1.50 and/ or necessary adhesive. (Only finished granite work shall be measured). All expose edges 2624.36 Hundred TwentyFour Paise Sqm

shall be champhered and polished. The rate includes making hole, cutting/ chasing, rounding ThirtySix Only

champhering, edge polishing of edges. The work shall be carried out as per the approval of

architect and engineer-in-charge.

Basin Counter/Granite Platform (All Floor : Width - 600 mm ) : Providing and constructing

approved shade and sample of Mirror finish granite platform , 600mm width 25 mm thick

Machine polished kotah stone as vertical supports at sides,including cutting granite & kotah as

Rupees Five Thousand Two

per required shape , dedo 1'6" ht & size to fit kitchen sink, moulding, tiles adhesive nosing,

46 7.36 5274.07 Hundred SeventyFour Paise Sqmt

chamfered front edges, fixing, disposal of debris etc complete with all labour and materials

and as per detailed drawings / architects instruction and approval by Engineer-in-charge. The

sample mock shall be approved from EIC.

Granite Cladding : Providing & laying in line and level minimum 18 mm thick (selected and

sorted for its uniform colour and thickness) Granite cladding of approved shade and quality on

internal wired finished or mala finished plastered surfaces as per drawing , size of the stone

shall be 1.20 meter x 0.9 meter. Granite shall be fixed with cement based, highly polymer

modified, and high strength, flexible tile adhesive "Diamond Star" of BAL Endura Make or

equivalent of approved colour of thickness as specified by manufacturer. Rate shall be inclusive

of filling the grooves of minimum 10 mm wide x 10 mm deep on both sides shall be filled with

approved colour & make neutral cure glazed & metal silicon sealant . The rate shall also include

for necessary mortar base , tools , tackles , etc . including cleaning, polishing, and scaffolding Rupees Two Thousand Two

47 12.36 etc complete at all heights, all places, and all shapes as per drawings and including laying in 2298.36 Hundred NinetyEight Paise Sqm

desired design and pattern and as per drawing or as directed by the Engineer-in-charge. Based ThirtySix Only

on available size of stones within the maximum size stated above will be considered for final

stone cladding pattern. Cladding shall be done only after allowing the walls to wet out for a

minimum exposure period of 6 weeks prior to rendering/ plastering/ tiling. Rate to be inclusive

of all material, wastage, necessary tools tackles etc for fixing at all heights and for all floors.

Clear laid area shall be measured & paid in sqm.

Gypsum Ceiling : Providing and fixing single layer water proof gypsum board 12.5 mm thick

sections using water proof board of size 1220 mm x 1830 mm x 8.0 mm suspended by GI

suspender channel of size 25 mm x 3 mm with intermediate channel og size 18 mm x 40 mm x

0.8 mm at 1220 mm center to center ceiling section of size 40 mm x 35 mm x 0.55 mm at

Rupees Six Hundred Six Paise

48 46.65 mm c/c and perimeter channel A of size 20 mm x 27 mm x 30 mm x 0.5 mm at edges & drops 606.95 Sqm

NinetyFive Only

incl.paper tap sand sofit cleat, anchor fastener, scoch bolt connecting cleat,joining compound

top coat on ceiling incl. making necy. opening for light fitting,diffuser etc. comp. as per detail

drawing as directed.

PLY WALL PANELING FINISH WITH PU FINISH : Providing & fixing 12mm thick IS 710 MR Grade

ply fixed on frame work. The framework shall be fixed as per drawing vertically & @ 600 mm

c/c vertical & 1200 mm c/c horizontally. The frame work shall be made from Ply make

conforming to IS specification In paneling, (intermediate, perimeter ) & (at vertical or

horizontal joint of ply & at turning point ) shall be fixed to the wall/floor & ceiling with Sheet

metal screws/Nylon grip screws of Corro-shield /Fischer, etc and shall be supported by filling

Rupees Three Thousand Five

required size wedges /washers/ MS wall connectors or packings of teak wood /MS washers

49 32.92 3502.57 Hundred Two Paise Sqm

to ensure right angles and plumb level. All ply/wooden frameworks shall be treated with anti-

FiftySeven Only

termite treatment & hidden The frame work shall be covered with approved make plywood(IS

710- 12 mm ply),adhesive ,tape, headless nails etc ,finished with MDF ( MDF base ply) with

semiglossy PU Paint & in pattern as shown in the drawing. Rate shall be inclusiveg grooves,

Hardware, fitting, fixture, scaffolding, adhesives, etc complete as per drawing or as directed by

False ceiling : Providing and fixing eco-friendly light weight calcium silicate false ceiling tiles

having Tegular edge & 15 mm Thick Densified edges on the Tile Periphery for Extra Strength The

Light weight calcium silicate ceiling tiles shall have , light reflection 85% non-combustible as per

B.S. 476 part IV, 100% humidity resistance and also having thermal conductivity0.043° w/m

KC.for the best thermal Insulation . The Light weight calcium Silicate tile shall be of approved

texture Fine fissured/Spintone/Cosmos having NRC value of 0.5 & Globe having NRC value of

0.75 NRC or equivalent of size 595 X 595 mm to be laid on true horizontal level suspended inter

locking metal grid of hot dipped galvanized steel sections (galvanizing @120 grams per sqm

including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length

and size of 24X38mm made from 0.30 mm thick (minimum) sheet, 1200mm centre to centre,

and cross ‘T’ of size 24X28mm made out of 0.33mm (Minimum) sheet spaced 1200mm along Rupees One Thousand Six

50 57.48 spaced between main ‘T’ at 600mm centre to centre to form agrid of 1200X600mm and 1674.15 Hundred SeventyFour Paise Sqm

secondary cross ’T’ of length 600mm and size 24x28mm made of 0.30 mm thick (Minimum) Fifteen Only

sheet to be interlocked at middle of the 1200X600mm panel to form grid of size 600X600mm

resting on periphery walls/partitions on a perimeter wall angle pre-coated steel of size

(24X24X3000mm made of 0.40mm thick (minimum) sheet with the help of rawl plugs at 450mm

centre to centre with 25mm long dry wall screws @ 230mm interval and laying 15mm thick

Densified edges light weight calcium silicate ceiling tiles of approved texture (Fine

Fissured/Cosmos/Spintone) in the grid including, cutting /making opening for services like

diffusers, grills, light fittings, fixtures, smoke detectors etc.,

Sr. Quantities Item of Work Estimated Unit Total

In Rupees In Words

wherever required, Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats of

size 25X35X1.6mm fixed to ceiling with 12.5mm dia and 50mm long dash fasteners, 4mm G.I.

adjustable rods with galvanized steel level clips of size 85X30X0.8mm, spaced at 1200mm

centre to centre long main ‘T’ bottom exposed with 24mm of all T-sections shall be prepainted

with polyester baked paint, for all heights, as per specifications, drawings and as directed by

engineer-in-charge.Note:- Only calcium silicate false ceiling area will be measured from wall to

wall. No deduction shall be made for exposed frames/opening (cut outs) having area less than 0

0.30 sqm. The calcium silicate ceiling tiles shall have NRC. Value of 0.50 (Minimum) for Fine

fissured/Spintone/Cosmos and 0.75 NRC for Globe, light reflection 85% noncombustible as per

B.S. 476 part IV, 100% humidity resistance and also having thermal conductivity. 0.043° w/m

KC.for the best thermal Insulation

Flush Door With WPC frame (37 mm) : Providing and fixing in position 35mm thick solid core

wooden flush doors of approved make having fire retardant ply facing on both sides and

finished with 1 mm thick laminate as approved , WPC frame size - 125 X 63 MM Well Quality Rupees Six Thousand Five

51 32.13 Hardware system of Hinges , Boxer type door closer , Door handle , Euro profile , lock ,Door 6570.17 Hundred Seventy Paise Sqm

stop . work complete including all type of hardware, fittings , fixtures etc complete as per Seventeen Only

detailed drawings and specifications, sample mock shall be approved from EIC.

Flush Door with frame and finish with 1mm thick Laminate (37MM): Providing and fixing in

position 35 mm thick solid core wooden flush doors of approved make having fire retardant ply

facing on both sides and finished with 1mm thick laminate as approved ,Indian Teak Wood

Rupees Four Thousand Seven

Frame size - 125 X 75 MM, Single rebet , Well Quality Hardware system of Hinges , Boxer type

52 46.56 4750.42 Hundred Fifty Paise Sqm

door closer , Door handle , Euro profile , lock ,Door stop . work complete including all type of

hardware, fittings , fixtures etc complete as per detailed drawings and specifications, sample

mock shall be approved from EIC.

Double Leaf Flush Door with frame and finish with 1mm thick Laminate (37MM): Providing

and fixing in position 35 mm thick solid core wooden flush doors of approved make having fire

retardant ply facing on both sides and finished with 1mm thick laminate as approved ,Indian

Rupees Four Thousand Eight

Teak Wood frame size - 250 X 75 MM double rebet , Well Quality Hardware system of Hinges

53 4.80 4899.17 Hundred NinetyNine Paise Sqm

Boxer type door closer , Door handle , Euro profile , lock ,Door stop . work complete including

all type of hardware, fittings , fixtures etc complete as per detailed drawings and specifications,

sample mock shall be approved from EIC.

Window : Providing and fixing factory made upvc fenesta wooden colour sliding glazed window

with Mosquito net and Approved sample by Architect/Client/EIC. all height dimension

comprising of upvc multi chambered frame with in built roller track and sash extruded profiles

duly reinforced with 1.60 + 0.2 mm thick galvanizd mild steel section made from roll forming

process of required lenght ( shape & size according to upvc profile ), appropriate dimension of

upvc extruded glazing beads and upvc extruded interlocks, epdm gasket,wool pile,zinc alloy

(white powder coated) touch locks with hook,zinc alloy body with single nylon rollers (weight

bearing capacity to be 40 kg),g.i. fasteners 100 x 8 mm size for fixing frame to finished wall and

necessary stainless steel screws etc. profile of frame & sash shall be mitred cut and fusion Rupees Twelve Thousand

welded at all corners,including drilling of holes for fixing hardware's and drainage of water etc. Four Paise Ten Only

after fixing frame the gap between frame and adjacent finished wall shall be filled with weather

proof silicon sealant over backer rod of required size and of approved quality,all complete as

per approved drawing & direction of engineer-in-charg. two track two panels sliding window of

5 mm thick toughen glass and series 2000 frame 65 x 58 mm & sash 45 x 90 mm both having

wall thickness of 1.9+ 0.2 mm and single glazing bead of appropriate dimension.

Providing and fixing S.S. bird net jali (Invisible Grill)- using wire gauge with average width of

aperture 1.4 mm in both directions with wire of dia. 0.50 mm all complete With Aluminium

equal angle frame or 12 mm mild steel U beading work at required opening and at any height

Rupees One Thousand Three

with all labour & material etc. complete. and fitting with necessary nuts, bolts, machine screws

55 141.29 1303.6 Hundred Three Paise Sixty Sqm

etc fixing i/c fixing with necessory accessories and dash / Anchor fasteners of required size. on

the top of floors, concretes, wood, walls, sides of slab with suitable arrangements. etc complete

for all floors and at all levels

Providing and fixing standared extruded of alluminium section of size 63.50 x 38.10 x

mm,@ Wt 1.094Kg / Rmt with colour anodized alluminium frame with 5 mm thick transparent Rupees One Thousand Five

bronze colour tinted float glass as details etc complete for Fix window. Hundred TwentyFive Only

Providing and fixing standared extruded of alluminium section of size 63mm x 38.10mm x

Rupees One Thousand One

1.2mm (Jindal Section:2434, @ Wt. 0.643 Kg/mt) with colour Powder Coated alluminium frame

57 4.32 1175.56 Hundred SeventyFive Paise Sqm

for ventilation with 5mm thick frosted glass as details etc complete for Ventilation. All Level

Providing and fixing M.S. grills of required pattern to wooden frames of windows etc. with M.S.

Rupees One Hundred Nine

58 1684.71 flats at required spacings and frame alround, square or round bars with round headed bolts and 109.08 Kg

Paise Eight Only

nuts or by screws (A) Plain Grill.

Fencing : Providing and fixing 'Y' shaped barbed wire fencing on compound wall top with

vertical angle of 50x50x6mmx0.50 mt. height, two cross angle 50x50x6mmx0.45mt. Length,

having 3 horizontal and two diagonal rows of barbed wire (9.38 kg/100 rmt) on vertical angle

Rupees Three Hundred

and three horizontal and two diagonal barbed wire rows on each cross angle incl. cost of

59 240.00 337.89 ThirtySeven Paise EightyNine Rmt

barbed wire, necessary GI stapplings, fixing on top of compound wall, painting angle with one

coat of anticorrosive primer and two coats of enamel paint of approved qaulity, necessary

scaffolding etc. complete as per the direction of the Engineer in charge.

Sr. Quantities Item of Work Estimated Unit Total

In Rupees In Words

Wall Punning : Providing and applying Plasto XP Gypsum plaster ( USG Boral) or equivalent

make , minimum 12 mm thick in Wall and minimum 6 mm thick in ceiling , including all labors,

tools, tackles, scaffolding, surface preparation, mixing of material, transportation (lead & lift)

applying in position, Levelling, finishing, cleaning etc. complete to satisfaction of Employer's

Rupees Three Hundred

60 50.00 representative/ Employer. The rate also include making of grooves above skirting, Dedo tiles 365.62 Sqm

SixtyFive Paise SixtyTwo Only

and around window and door jambs etc. (cost of Bonding agent to the ceiling or RCC surfaces is

to be included in the item).item shall be used as per instruction of the Engineer-in-Charge.

TV UNIT : Providing & fixing projector drawer unit As per detail drawing and reference image

and detail shape & size with require accessories. Top 35 MM th made from 12 mm th IS

ply & Laminate finish Storage body is made of 19mm 303 MR Grade ply with 1 mm laminate

finish and inner side 1 mm thick laminate finish including require nos of drawer with all type of

fittings ,cutout for air cerculation , require fixtures, hardware Hettich/Haffle make etc

complete .SS 304 grade conceal handle shall be provide as per approved selection &detailed

Rupees Fifteen Thousand Six

drawing and instruction of Employer's representative/ Employer.Rate shall incusive require

61 1.29 15651.02 Hundred FiftyOne Paise Two Sqm

fabrication work considering load capasity of AV equipment.The work shall be done as per the

approved specifications, sample approved and as directed by the Architect and Engineer-in-

charge. The rate shall be for complete item inclusive of all material, labour, wastages, necessary

tools & tackles, adhesives consumable hardware & required SS 304 grade

hardware/accessories of approved make.

GRC WORK : Providing & fixing architectural moldings profiles and other decorative elements

made out of GRC (Glass Fibre reinforced Cement) in required shape, size & thickness all as per

manufacturers specifications, such as all decorative articles should be made by using high

power spray machine, using AR Glass fiber with minimum ZrO2 16% including necessary

scaffoldings for all heights, as per approved drawings and reference images. GRC elements

thickness shall be 12-15 mm. fixing edges will be 4O TO 50 MM GRC Elements shall be fixed on

RCC Structure/Brick Work/ Primary Steel Structure (MS with protective coat of Red oxide/Zinc

Primer Shall be Used). Hilti make GI Screw Fastners or equvalent, GI Thread Rods and MS cleats Rupees Five Thousand Six

62 84.94 shall be used for fixing of GRC elements on RCC/MS Primary fabricated structure. Joints shall be 5609.85 Hundred Nine Paise Sqm

filled with PU sealants/ base material of GRC as and where required. The quote rate shall be EightyFive Only

inclusive of all design, & shop drawing and sample mock of all elements approval from

Architect & consultant. Rate shall be inclusive of all required fabrication work for fixing only

primary strcure shall be provided as base structre only as per requirement. Mode and method

of measurement shall be in accordance with IS: 1200.a )GRC JALI-As per above specification

work. (Elevation area)

Applying two coats of putty & two coats of primer of approved brand and manufacture on new

wall surface to give an even shade including thoroughly brushing the surface free from mortar Rupees Fourty Paise FiftyNine

dropping and other foreign matter and sand papered smooth. Only

Wall painting (two coats) with plastic emulsion paint of approved brand and manufacture on

undecorated wall surface to give an even shade including throughly brushing the surface free Rupees EightyFour Paise

from mortar droppings and other foreign matter and sand papered smooth. ThirtySeven Only

Finishing wall with weather proof exterior emulsion paint on wall surface (two coats) to give an

Rupees One Hundred Twenty

65 2355.50 required shape even shade after thoroughly brushing the surface to remove all dirt, and 120.26 Sqm

Paise TwentySix Only

remains of loose powdered materials. etc complete

Applying priming coat over new steel and other metel surface after and including preparing the

surface by throughly cleaning, oil, grease, dirt and other foreign matter and scoured with Rupees ThirtySix Paise

brushes fine steel wood, scrapers and sand paper with ready mixed priming paint brushing red FourtyTwo Only

Painting two coats (excluding priming coat) on new steel and other metal surface with enamel

Paint, brushing, interior to give an even shade including cleaning the surface an even shade Rupees NinetyTwo Paise

including cleanicn the surface of all dirt, dust and other foreign matter. Twenty Only

Steel work, welded in built up sections framed work including cutting, hoisting, fixing in position

and applying a priming coat of red lead paint. (A)In beams and joists, channels angles Tees, flats, Rupees Nine Thousand One

68 91.94 with connecting plates or angle cleats as in main and cross beams. Hip and jack rafters, purlins 9108.48 Hundred Eight Paise Qui.

conneted to common rafters and the like FourtyEight Only

Providing in position PVC pipe sleeves of 6Kg/cm2 and length as per design for following

diameters for services wherever pipes pass through walls/ slabs/ beam in mtrs length. All pipes

shall be accurately cut to the required sizes, laid as per drawing, kept in the position while

Rupees One Hundred Sixteen

69 12.00 concreting, and burrs removed before laying. Open ends of the pipe shall be closed as the pipe 116.15 Rmt

Paise Fifteen Only

is installed to avoid clogging while concreting. Rate shall be inclusive of removal of sleeves

before water proofing or grouting. For all floors / all levels / all heights. (a) 50mm Diameter

Providing in position PVC pipe sleeves of 6Kg/cm2 and length as per design for following

diameters for services wherever pipes pass through walls/ slabs/ beam in mtrs length. All pipes

shall be accurately cut to the required sizes, laid as per drawing, kept in the position while Rupees One Hundred

70 12.00 concreting, and burrs removed before laying. Open ends of the pipe shall be closed as the pipe 185.84 EightyFive Paise EightyFour Rmt

is installed to avoid clogging while concreting. Rate shall be inclusive of removal of sleeves Only

before water proofing or grouting. For all floors / all levels / all heights. (a) 75mm Diameter

Sr. Quantities Item of Work Estimated Unit Total

In Rupees In Words

Providing in position PVC pipe sleeves of 6Kg/cm2 and length as per design for following

diameters for services wherever pipes pass through walls/ slabs/ beam in mtrs length. All pipes

shall be accurately cut to the required sizes, laid as per drawing, kept in the position while Rupees Three Hundred

71 12.00 concreting, and burrs removed before laying. Open ends of the pipe shall be closed as the pipe 319.41 Nineteen Paise FourtyOne Rmt

is installed to avoid clogging while concreting. Rate shall be inclusive of removal of sleeves Only

before water proofing or grouting. For all floors / all levels / all heights. (a) 110mm Diameter

Providing in position PVC pipe sleeves of 6Kg/cm2 and length as per design for following

diameters for services wherever pipes pass through walls/ slabs/ beam in mtrs length. All pipes

shall be accurately cut to the required sizes, laid as per drawing, kept in the position while Rupees Four Hundred

72 12.00 concreting, and burrs removed before laying. Open ends of the pipe shall be closed as the pipe 499.45 NinetyNine Paise FourtyFive Rmt

is installed to avoid clogging while concreting. Rate shall be inclusive of removal of sleeves Only

before water proofing or grouting. For all floors / all levels / all heights. (a) 160mm Diameter

Core cutting : Providing and wet drilling accurate and clean holes of specified diameter in RCC

walls, slabs, beam or any other RCC member without vibration by core cutting (diamond

drilling) machine including scafolding, safety majors, disposing the debris, cleaning for all levels/

Rupees One Thousand One

all height as per structural consultant's drawing, after approval of engineer in charge etc

73 20.00 1126.66 Hundred TwentySix Paise Nos

compete. Rate shall be inclusive of filling the hole with non shrink grout/Chemical Anchoring in

good manner. Measurement shall be taken for the depth of holes in running meter for specified

diameter. Holes shall made by authorised approved agency. (a) holes from 100 dia.

Core cutting : Providing and wet drilling accurate and clean holes of specified diameter in RCC

walls, slabs, beam or any other RCC member without vibration by core cutting (diamond

drilling) machine including scafolding, safety majors, disposing the debris, cleaning for all levels/

Rupees One Thousand Four

all height as per structural consultant's drawing, after approval of engineer in charge etc

74 15.00 1463.49 Hundred SixtyThree Paise Nos

compete. Rate shall be inclusive of filling the hole with non shrink grout//Chemical Anchoring in

FourtyNine Only

good manner. Measurement shall be taken for the depth of holes in running meter for specified

diameter. Holes shall made by authorised approved agency. (b) holes from 150 dia.

Providing and fixing anchor fastener system chemical based of Hilti or equivalent make for

connections in concrete as per design and drawings and/or as directed by engineer in charge.

(Rate shall include cost of bolts, labour, all material including chemical cartridge (wherever

required). T & P for power drilling, cleaning the drilled holes of loose dust by blowing air,

Rupees One Hundred

insertion of chemical from cartridge with plastic nozzles as may be required, placing internally

75 10.00 197.46 NinetySeven Paise FourtySix Nos

threaded sleeve, driving of bolts, 2 nos-4 mm thick (hot dip galvanized coated) washer,

fastening screw and tightening with nuts and check nuts etc may be required.Work complete

including all type of tools , tackles, scaffolding etc complete at any level and height. work

complete as per the instruction of EIC/Client/Architect. 12 mm dia.

Providing and fixing anchor fastener system chemical based of Hilti or equivalent make for

connections in concrete as per design and drawings and/or as directed by engineer in charge.

(Rate shall include cost of bolts, labour, all material including chemical cartridge (wherever

required). T & P for power drilling, cleaning the drilled holes of loose dust by blowing air,

Rupees Four Hundred

insertion of chemical from cartridge with plastic nozzles as may be required, placing internally

76 10.00 441.37 FourtyOne Paise ThirtySeven Nos

threaded sleeve, driving of bolts, 2 nos-4 mm thick (hot dip galvanized coated) washer,

fastening screw and tightening with nuts and check nuts etc may be required.Work complete

including all type of tools , tackles, scaffolding etc complete at any level and height. work

complete as per the instruction of EIC/Client/Architect. 16 mm dia.

Providing and fixing anchor fastener system chemical based of Hilti or equivalent make for

connections in concrete as per design and drawings and/or as directed by engineer in charge.

(Rate shall include cost of bolts, labour, all material including chemical cartridge (wherever

required). T & P for power drilling, cleaning the drilled holes of loose dust by blowing air,

insertion of chemical from cartridge with plastic nozzles as may be required, placing internally Rupees Eight Hundred Thirty

threaded sleeve, driving of bolts, 2 nos-4 mm thick (hot dip galvanized coated) washer, Paise FourtySeven Only

fastening screw and tightening with nuts and check nuts etc may be required.Work complete

including all type of tools , tackles, scaffolding etc complete at any level and height. work

complete as per the instruction of EIC/Client/Architect. 20mm dia.

SS RAILING :Providing & Fixing Stainless steel 304 grade pipe railing Horizontal 50 mm dia.

Nos. and Supprt pipe from wall 16mm Dia. at everymax 0.90mtr C/C including welding,

grinding, buffing, polishing and making curvature (wherever required) and fitting the same with

Rupees Two Thousand Eight

necessary stainless steel nuts, Plates and bolts complete, i/c fixing the railing with necessary

78 20.00 2872.66 Hundred SeventyTwo Paise Rmt

accessories & stainless steel dash fasteners, stainless steel bolts etc., fixed on Concrete or brick

work . Rate including of all materials.labour, fixing & polishing etc. comp. as per Drawing and

Approve by Engineer In Charge

SS RAILING : Providing and fixing stainless steel (Grade 304) railing Horizontal top pipe of 50mm

dia., verticle Sq pipe 32X32 mm 900 mm c/c and 16 mm Dia. 3 Nos. Horizontal Pipe equval

Spacing Hollow Pipes, channels, plates etc., including welding, grinding, buffing, polishing and

making curvature (wherever required) and fitting the same with necessary stainless steel nuts,

Plates and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash Rupees Three Thousand

79 51.60 fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist 3764.88 Seven Hundred SixtyFour Rmt

slab with suitable arrangement as per approval of Engineer-in charge, (for payment purpose Paise EightyEight Only

only weight of stainless steel members shall be considered including fixing accessories such as

nuts, bolts, fasteners etc.). as per Drawing and Approve by Engineer In Charge

Sr. Quantities Item of Work Estimated Unit Total

In Rupees In Words

Roller blind : Providing and fixing of approved quality roller blinds using phifer or equivalent

fabric of premium grade, with roller tube, bottom bar leveller made of extruded aluminium

alloy an Idler, Insert Type- Brackets, PVC chain etc. all complete at all floor and heights as per

approved specification. Roller Tube Control, Clutch, Idler Side by side or single Roller Tube of

extruded Aluminium 38mm inner dia - 41mm outer dia minimum wall thickness of 1.6mm.

Roller blind - roller blind fabric should be made up of 35% FibreGlass, 65% PVC, it should have

specific low emissivity treatment and lead free with Greenguard gold certification. It should Rupees One Thousand Seven

80 141.29 have 3% to 5% openness, fabric thickness should be 0.43 mm, mesh weight approx 400 gms/ 1724.69 Hundred TwentyFour Paise Sqm

sqmtr. It should cut UV rays, with antimicrobial properties preferably with Microban. The fabirc SixtyNine Only

should be Flame retardant and Lead Free. It should be GreenGuard certified with Gold Standard

for low chemical emissions for indoor use. including all accessories, material, labour,installation

etc..and complete the work satisfactorily as per instruction of architect or Engineer-in charge.

White washing with lime on wall surface (three coats) to give an even shade incl. thoroughly

brooming the surface to remove all dirt, dust, mortar drops and extra subsequent coat of white Rupees Eighteen Paise

washing with lime on wall surface. FiftyFive Only

Soft Board : Providing and fixing on wall 12mm thick approved quality soft board with cotton

cloth/fabric of approved make and shade on 12mm thick IS 710 MR Grade ply with 19mm x

mm thick Ghana teak wood beading all around including semi glossy PU polish, as approved

sample and as directed by Architect. The work shall be measured & paid in Sqm. for all floors, Rupees Two Thousand Seven

all level and at all heights including all costs, The rate shall be inclusive of lacquer polish to all Hundred Ten Paise One Only

the exposed wooden members. Only the clear elevation area of the cloth/fabric shall be

measured and paid.

Providing and applying Lacquer polish of approved make and finish on new wood and wood

based surface to give an even surface, including cleaning the surface of all dirt, dust and sand

papered smooth and including a coat of wood file after completion of job etc. to the

satisfaction of architects / EIC. (Mode of measurements: Only the polished area shall be Rupees Three Hundred

83 21.00 measured & paid for the items in which polishing is not inclusive in item description) work shall 377.49 SeventySeven Paise Sqmt

be carried out as per the manufacture's specification & sample approved..(Exposed wooden FourtyNine Only

surface at all floor) (Mode of Measurements: Only the polished area shall be measured & paid

for the items in which polishing is not inclusive in item description)

Ply palmet work : Providing and fixing wooden pelmets of upto 150mm/950 mm x 150 to

mm L shape made of 19mm thick ply as per IS 710 MR Grade and beading of 1.0 mm thick

Laminate for curtains/ blinds/ projection screen of openings. Rate to be inclusive of lipping,

Rupees One Thousand Seven

cutting, wastages, necessary fixtures, nails, adhesives, necessary scaffolding, fixing at all heights

84 66.50 1778.38 Hundred SeventyEight Paise Rmt

and for all floors as per drawing and approved sample etc finish with veneer semi gloss PU

ThirtyEight Only

finsh. (Mode of Measurements: Only the palmet length shall be measured & paid for the items

in which palmet work is not inclusive in item description)

Lawn plantation : Individual Grass Crop Installation

This work includes the supply and installation of healthy, well-rooted individual grass plants for

the development of a lawn. The surface shall be properly prepared by leveling, removing debris,

and ensuring suitable soil conditions for plantation.

Farmyard manure shall be mixed thoroughly with the topsoil before planting to enhance soil Rupees Six Hundred

85 1917.60 fertility and promote healthy grass growth. Individual grass crops shall be planted at uniform 648.19 FourtyEight Paise Nineteen Sqm

spacing for even coverage and proper rooting. Only

After installation, the lawn shall be maintained for a period of three months, including regular

watering, weeding, gap filling, trimming, and application of manure or fertilizer as required to

ensure a dense, uniform, and healthy green lawn.

Providing & Laying Tree plantation including providing and fixing tree guard. Rate also inclusive

Rupees Six Hundred ThirtySix

86 50.00 of maintaining the tree plant in live condition at the time of completion of work. Rate are 636.3 Nos.

Paise Thirty Only

including providing necessary tree guard.

Convex Mirror is a curved mirror : Providing and supplying Convex Mirror as per references

image, detail and approved sample by Architect/EIC. The Convex Safety Mirror is structured

with a polycarbonated front and acrylic back which makes it lighter and easy to place on any

exterior. It also looks like a bubble mirror that has a curvature of the 130-degree view. The

Convex Mirror comes with a protective film coating that makes the traffic mirror scratch-

resistant, break-resistant, and tear-proof.The Polycarbonate Lens reflects a crystal clear and

bright image of the view which can be seen from a long distance. It also magnifies the opposite

Rupees Two Thousand Nine

fronts that help the drivers to locate small things clearly. The contractor shall Convex Mirror

87 1.00 2903.75 Hundred Three Paise Each

with Installation Kit, Nuts & Bolts Included support, Location, any Height and all complet

SeventyFive Only

installation work as per site condition. This Item includes cost of all labour, transfort etc. as

required for completing the work in all respects. All works are carried as per approval and

instructions of the architect. Rate shall inclusive of sample, all materials, loading, unloading, all

taxes, transportation, placing at all floors and for all leads,all accessories as described in item

Sr. Quantities Item of Work Estimated Unit Total

In Rupees In Words

Road Marking with hot applied thermoplastic paints with reflectorising glass beads on

bitumen/RCC surface providing and laying a hot applied thermoplastic compound 2.5mm thick

including reflectorising glass beads @250gms/m2 area , thickness of 2.5mm is excluding of

surface applied glass beads as per IRC: 35-2015. The finished surface to be levelled, uniform and

free from streaks and holes. Thermoplastic paint shall be used for Zebra Patta, Bump Patta lane,

Rupees Three Hundred

edge line, cut patta, arrows for direction, letter or number writing etc. The white colour

88 12.50 367.72 SixtySeven Paise SeventyTwo Sqm

marking should provide liminance co-efficient on cement road shall be min 130 mcd/m2/lux

and Asphalt road shall be min 100 mcd/m2/lux during the service life during the day time the

marking should make the performance criteria for night time reflectivity, wet reflectivity and

skid resistance as mentioned in the section- 15 of IRC: 35-2015. Warranty for retro reflectivity

shall be 2(Two) years.

Providing and fixing of Corner Guard for Various Flashing in 100mm x 100mm size in Equal

Shape with 5mm edge lipping on both side . The Angle Flashing shall be made out of 8 to 10 mm

Rupees Three Hundred

thick, The corner guard shall have plastic protective guard film of minimum 25 microns to avoid

89 4.00 372.84 SeventyTwo Paise EightyFour Nos

scratches during transportation. The U track shall be fixed with suitable POP rivet with wall and

roof panels with minimum spacing of 450 mm c/c. size of guard 1000mm length

Providing and fixing Rumblers strips of required size with any design suggested by Architectect/

EIC like bottom design, chequered design, anti skid pattern specially designed for road grip as

Rupees One Thousand Seven

per drawing & sample approved by Architect which is covered with premix bituminous carpet at

90 10.00 1788.71 Hundred EightyEight Paise Rmt

1m centre to centre at approved locations to control speed marked with white strips of road

SeventyOne Only

marking paint etc complete as directed by Engineer in charge.

Cat Eye/Road Stud/RPM : Supplying of Molded TwinShanks Raised Pavement Markers made of

polycarbonate and ABS moulded body and reflective panel swith micro prismatic lens capable

of providing total internal reflection of the lightenteringthe lens face and shall support a loadof

13635kgs. tested in accordance to ASTMD4280Type Handcomplying to Specifications of

Category A of MORTH Circular No RW/NH/33023/10-97 DO III Dt 11.06. 1997. The height, width

and length shall not exceed 20mm, 130mm and 130mm and with minimum reflective area of

Rupees Three Hundred

13Sq cmon each side and thes lope to the base shall be 35+/-5 degree.The strength of

91 38.00 326.23 TwentySix Paise TwentyThree Each

detachment of the integrated cylindrical shanks, (of diameter not less than19+/-2mm and

height not less than 30+/2mm) from the body is to be a minimum value of 500Kgf. Fixing will be

by drilling holes on the road for the shanks togo inside, without nails and using epoxy resin

based adhesive as per manufacturers recommendation and The color of the marker should be

as per the IRC 35-2015 and as directed by Engineer-in-charge.

GRANITE Counter : (500 D) : Providing, making, fixing as per detail drawing and required

length and depth shelf made from 18 mm Granite (1-Cement: 4- fine sand ) with one side finish

polished, round edge and providing lighting arrangement cutout and fixing as per detail drawing Rupees Two Thousand One

92 0.75 and instruction of EIC.Rate shall inclusive all necessary hardware and fitting.The work shall be 2104.41 Hundred Four Paise Sqm

done as per the specifications, sample approved and as directed by the Architect and Engineer- FourtyOne Only

in-charge. .Rate shall inclusive of providing mock up sample for approval of Architect.

Wooden Shelf : Providing, making, fixing as per detail drawing made from 19 mm IS 710 BWP

ply structure aand both side 1 mm thick laminate finish shall be of approved make & shade and

as per the detail drawing. All the edges of ply shall be covered with 1 mm thick laminate finish

Rate shall also inclusive of all necessary,The rate shall be inclusive of shelf both side 1 mm

thick laminatefinish and as per detail drawer unit for Wooden Shelf as per selction by architect

The rate shall be in sqm of elevation area for all floors and at all heights including all costs

Rupees Five Thousand Three

complete as per the Architectural drawings & instructions.Only the elevation area of the

93 11.77 5398.54 Hundred NinetyEight Paise Sqm

storage unit will be measured and paid for. Item for 1 mm thick laminate fixing and polishing is

included in this item. The work shall be measured & paid in sqm The rates shall be inclusive of

all wastages, material, labor, taxes, transportation, loading, unloading, fixing in position, etc.

complete to the satisfaction of the Architect and EIC. The mock-up of 1 unit shall be approved

from EIC and Architecture prior to the final production.

Direct Bought Out Item : Providing and placing in position SS brush finish (12 LTS PEDAL BIN/ Rupees One Thousand One

94 8.00 STEP BIN -) of Kich , Dorma ,etc Square Pedal bin 10x15 Stainless Steel Dustbin or Equivalent as 1184.73 Hundred EightyFour Paise Nos

per images and as selected by the Architect. SeventyThree Only

Providing and supplying of Dustbin of Approved Brand Sintex or equivalent of 40-50 Liters Rupees One Thousand Eight

95 2.00 capacity. 1811.94 Hundred Eleven Paise Nos

NinetyFour Only

Artificial Plant : Providing and supplying planters with plant as per selection of Architect. Item

includes cost of all labour, transfort etc. as required for completing the work in all respects. All Rupees Three Thousand One

96 5.00 works are carried as per approval and instructions of the architect. Rate shall inclusive of 3153.47 Hundred FiftyThree Paise Nos

sample, all materials, loading, unloading, transportation, placing at all floors and for all leads. FourtySeven Only

Providing and fixing Sainless steel signage plate of 1.5mm thick with laser print/ etching and

Rupees Seven Thousand Two

filled with duco paint of approved make including fixing to the wall or door with required

97 0.75 7285.33 Hundred EightyFive Paise smt

acessories and as specified type including fixing etc complete as directed by engineer in charge

ThirtyThree Only

DOOR MAT : 3M Nomad - Wiping technology - Heavy Duty 7150 - or eqvivalant approved make

Grey Colour: Open Contruction Loop Matting with Crush Resilient Vinyl with backing. Matting Rupees One Thousand Two

98 4.05 Should be durabe shouldn't Flatten ove time. Thickness Should be 13mm Min.Suitable for heavy 1261.39 Hundred SixtyOne Paise Sqm

traffic areas, where traffic is upto 4 lakh people per year. work complete as per approved ThirtyNine Only

Providing & placing in position DIGITAL CLOCK - WALL MOUNTED as per architect selection

Rupees Two Thousand

99 11.00 Ajanta Digital Wall Clock(Brown, Black, With Glass) 2079.09 Nos

SeventyNine Paise Nine Only

Sr. Quantities Item of Work Estimated Unit Total

In Rupees In Words

Signages : Providing and fixing of the following signages using make of cosign or equivalent

approved make by architect.All the detailed work out as per the detailed drawing and

instruction of EIC., specifications and drawings as indicated there in to all heights and elevation

including necessary scaffoldings / supports /permanant fixing with cement mortor if fixed to

Rupees One Thousand Eight

ground etc complete in all respects.The Signage cost should be inclusive of panels,hanging

100 13.00 1888.6 Hundred EightyEight Paise Nos

system, bridges, primary & secondary fixings, vinyl, painting, powder coating self glowing

mateial as directed etc.All shop drawings and coordination with other services is in scopeof

contractor.( At all floor) Size (150 x 600mm) - FACE /WALL MOUNTED NAME

PLATES/SIGNAGES/INFORMATION SIGNAGES (with back lit)

Providing, supplying and placing World Globe - as per sample approved by architect Rupees Seven Hundred

101 1.00 749.17 FourtyNine Paise Seventeen Nos

Providing and placing in position vinyl printed MAP of size 54"x65" mm with teak wooden frame Rupees Four Thousand Four

102 1.00 with polishing . (At all floor) 4431.12 Hundred ThirtyOne Paise Nos

Natural Plant : Providing and planting of natural plants, healthy, well-grown, and free from

diseases, of approved species and variety, by Architect. Item includes cost of all labour, supply, Rupees Four Thousand

103 30.00 transportation, handling, excavation of pits, planting with good quality garden soil and manure, 4065.25 SixtyFive Paise TwentyFive Nos

watering, staking, and minimum plant height 10' with pvc pot , complete as directed by the Only

Engineer-in-Charge

Providing and installation of Granite Foundation stone/inauguration plank 18-19mm thick Rupees Six Thousand Two

104 7.20 engraved with writing provided by EIC and engraved filled with golden colour and with a 6295.02 Hundred NinetyFive Paise Smt

wooden frame. Two Only

Providing and Fixing the S.S. 304 Letters with back light of given size as per Architect's drawings

and approved sample or make (Approx Height of each letter 18 to 24 inches) along with all

necessary hardwares, scaffolding, Alu/MS Back support, hanging support and accessories, The

Rupees TwentyTwo Thousand

rate shall be for complete item inclusive of all material, labour, wastages, necessary tools &

105 23.00 22649.25 Six Hundred FourtyNine Paise Each

tackles, for all floors, all heights, all levels and all places within campus. Contractor shall do all

TwentyFive Only

the needful and shall fulfill Architect's design intent. No additional claims will be entertained for

this. (Consider Letter : TALUKA LIBRARY NAKHATRANA)

Providing and Fixing the S.S. 304 Letters of given size as per Architect's drawings and approved

sample or make (Approx Height of each letter 4 to 6 inches) along with all necessary hardwares,

scaffolding, Alu/MS Back support, hanging support and accessories, The rate shall be for

Rupees Six Hundred Three

106 323.00 complete item inclusive of all material, labour, wastages, necessary tools & tackles, for all 603.98 Each

Paise NinetyEight Only

floors, all heights, all levels and all places within campus. Contractor shall do all the needful and

shall fulfill Architect's design intent. No additional claims will be entertained for this.

Providing and fixing Godess Saraswati idol (Material- Fibre) 5 ft tall, with proportionately base Rupees One Lakh FiftySix

107 1.00 dimenstion as per approved design by client and complete as per instruction of engineer-in 156802.5 Thousand Eight Hundred Two Each

charge and consultant. Paise Fifty Only

PLUMBING FIXTURE : Providing, fixing, jointing and testing in position of various Bathroom C.P. Rupees One Thousand Four

108 7.00 Fixtures with hydraulic testing complete as per design, drawing and instruction of site incharge. 1451.88 Hundred FiftyOne Paise Nos

25mm Dia Control Valve EightyEight Only

Providing and fixing screw down bib taps of following size. (B) Brass chromium plated screws Rupees Two Thousand Paise

down Bib Tap. (i) 15mm dia. Ten Only

Providing and fixing health faucet with 1 m PVC tube and swivel hook including all fittings Rupees One Thousand Five

110 10.00 complete. 1585.45 Hundred EightyFive Paise Nos

FourtyFive Only

Providing, fixing, jointing and testing in position of various Bathroom C.P. Fixtures (Angle Cock) Rupees Two Thousand Two

111 4.00 with hydraulic testing complete as per design, drawing and instruction of site incharge. Urinal 2268.41 Hundred SixtyEight Paise Nos

stop cock. FourtyOne Only

Providing and fixing white glazed vitreous china wall mounting type (European type) water

closet with C.P. bolts, nuts, C.I. Chair or other hanging arrangement, white solid plastic seat

with lid, C.P. brass hinges and rubber buffers, Metropole flush valve reguler 40mm size Rupees Seventeen Thousand

112 10.00 (concealed body) with exposed shut off provision , C.P. brass screws and washers complete, 17968.41 Nine Hundred SixtyEight Paise Nos

including cutting and making good the walls floors where required. Wall hung EWC matching FourtyOne Only

white plastic seat with lid & CP brass hinges & CP push plate .

Providing and fixing White glazed vitreous Wash Basin Round Over-Counter, size 450 mm dia.,

with supporting in stone flooring, 1 no, 32 mm CP Bottle trap with extension piece to wall flange Rupees Five Thousand Eight

113 11.00 with rubber adopter for waste connection,1.2m Flexible Pipe [1No] and waste coupling. Etc 5819.81 Hundred Nineteen Paise Nos

complete. Wash Basin Table Top - 420x420x155 mm EightyOne Only

Providing & fixing in position 15 mm C.P. brass angle cock of best quality with 1.2 Rmt Long pvc Rupees Two Thousand

114 11.00 Tube and accessories with necessary fittings etc. complete. 2073.28 SeventyThree Paise Nos

TwentyEight Only

Providing & fixing in position 15 mm C.P. brass pillar cock of best quality with necessary fittings Rupees One Thousand Seven

115 11.00 etc. complete. 1751.75 Hundred FiftyOne Paise Nos

SeventyFive Only

Providing and fixing TOWEL RING SQUARE , as approved by the architect. Work complete

Rupees Nine Hundred

116 10.00 including all type of fittings, etc complete as per suggestion of Architect/EIC. 974.01 Nos

SeventyFour Paise One Only

Providing and fixing SOAP DISH HOLDER as approved by the architect. Work complete including

Rupees One Thousand Three

all type of fittings , etc complete as per suggestion of Architect/EIC.

117 11.00 1344.74 Hundred FourtyFour Paise Nos

SeventyFour Only

Sr. Quantities Item of Work Estimated Unit Total

In Rupees In Words

Supply, Installation, Testing & Commissioning vitreous matrix set (For Handicap) including

matrix EWC (European type water closet) with cistern, wall hung matrix wash basin, lever arm

Rupees FiftyThree Thousand

faucet for ease of operation, centre pre-punched tap hole, grab bar with slightly lower height

118 1.00 53924.73 Nine Hundred TwentyFour Nos

for added convenience & fixed to wall with brackets including cutting and making good the wall

Paise SeventyThree Only

and floors as required. Colour Star White.

Providing and fixing Urinal of approved quality including connection with trap and with integral Rupees One Thousand Six

119 4.00 longitudinal flush pipe.(A) Squating plate pattern white earthenware 550mm x 300mm. 1628.53 Hundred TwentyEight Paise Each

FiftyThree Only

Providing and fixing Kitchen sink with C.I. Or M.S. brackets, painted white including cutting Rupees Two Thousand Three

120 2.00 holes in walls and making good the same but excluding fittings. (C) Vitreous China Sink.(i) 2326.66 Hundred TwentySix Paise Each

600mm x 450mm x 150mm size SixtySix Only

Providing and fixing 600mm x 450mm bevelled edge mirror of superior glass mounted on 6mm Rupees Eight Hundred

121 11.00 thick A.C. sheet or plywood sheet and fixing to wooden pluge with C.P. brass screws and 859.41 FiftyNine Paise FourtyOne Each

Total of Civil & Interior work (A)

Drilling 300mm dia.pilot hole hydrolic drilling machine & drilling trully vertically (testing by

vertically test) bore hole in alluvial strata,any kind of soil incl.sand,murrum,hard murrum,soft

Rupees One Thousand Six

rock,hard rock incl.cost of bentonite powder done by mud flushed rottary equipment bore hole

122 300.00 1634.2 Hundred ThirtyFour Paise Rmt

should stand at least for 27hrs.incl.lowering the pipes in position as directed and incl.supplying

and packing gravel of 4mm to 6 mm size etc. comp. as directed.

Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (Electric

Resistance Welded) FE 410 mild steel screwed and socketed/plain ended casing pipes of

required dia, conforming to IS: 4270, of reputed & approved make, including painted with

outside surface with two coats of anticorrosive paint of approved brand and manufacture, Rupees Three Thousand Nine

including required hire & labour charges, fittings & accessories, all complete, for all depths, as Hundred SeventyFive Only

per direction of Engineer-in-charge.

(B) 200 mm nominal 6 mm thick

Development of hole by air compressor having capacity 400 cfm/100 psi till sand free discharge Rupees TwentyOne Thousand

124 1.00 of water incl.testing of water supply flow etc. comp. as directed. 21806.68 Eight Hundred Six Paise Job

SixtyEight Only

Providing & laying approved make ISI marked HDPE 6Kg / cm2 (Class-3) as per IS:4984:1995

Rupees One Hundred

PE-80 to be erected at road crossing on or floor as directed for laying of cable. The pipes as

125 250.00 163.62 SixtyThree Paise SixtyTwo LS

following size of dia & weight per 6 mtr

(B) 50 mm inner Dia.

Supplying & Fixing 50 mm dia heavy top bottom piece,G.I.Bend,Coupling,sand guard MS clamp Rupees Five Thousand Nine

126 1.00 with Nut Bolt etc.complete as directed by EIC. 5968.6 Hundred SixtyEight Paise Sixty Set

Water Analysis test in Govt.approved laboratory incl. all water testing etc. comp. as directed Rupees Three Thousand

127 1.00 3361.15 Three Hundred SixtyOne Nos.

Paise Fifteen Only

Providing water harvesting pit of 5.50 m Dia well and 2.46 mt x 2.46mt x 4.00 mt size brick

masonary well for water logging with excavation in any strata upto four meter depth, filling the

Rupees One Lakh FourtyEight

pit with B.T. Metal 40 mm in 0.80 mt. depth with 25-40mm kapachi, 0.80 mt. depth and

Thousand Three Hundred

128 1.00 mt. depth with coarse sand & charcoal in layers including making P.V.C. line for water inlet etc. 148396.84 Nos

NinetySix Paise EightyFour

as directed with 300mm dia bore 40 mt. depth and 200mm dia UPVC CM type casing pipe as

slott 1.5 to 2.0 mm size and ordinary pipe with gravel packing or as directed.

Providing and constructing filter chamber of size 1.50 x 1.50 x 1.50 mt. as directed including

Rupees TwentyOne Thousand

connection rainwater pipes as per detailed as directed by Engineer in charge including cost of

129 1.00 21721.55 Seven Hundred TwentyOne Nos

labour and material

Paise FiftyFive Only

RCC Hume Pipe : Providing & laying. R.C.C. Hume pipe for cable to be laid 90 cm. below ground Rupees Three Hundred

130 50.00 across the road crossing or on floor with necessary material in an approved manner and making 343.4 FourtyThree Paise Fourty Rmt

the ground as per original.(C) 300 mm dia Only

Total of BORE WELL & GD work (B)

Table : Providing & fixing office table / staff table having ht of 750 mm Top, with 19mm thk

plywood as per Architect/ Engineer Design or Selection and Back and side Ply of table is also

made up of 19mm Thick. Top of Table is 19mm thk ply with laminate Finish Per Requirement

and All internal & external Joints finished with teakwood beading Patti. Item includes fixing of

drawers and keyboard tray and storage with shutters under table as per drawing. With grooves

Rupees TwentyTwo Thousand

shown as per drawing. All exposed and internal surfaces covered with Laminate Finish of

131 3.86 22938.38 Nine Hundred ThirtyEight Sqm

approved shade & Complete as per detail drawings & as instructed by Architect/consultant/

Paise ThirtyEight Only

Engineer In charge. Complete with all necessary hardware like nails, ss screws, table chain, TDS

channel, adhesives etc. Contractor has to provide all necessary cut outs for Electrical works &

no extra payment shall be made for it. All ply should follow IS

Reading Table/Work Station : Providing & fixing work station / table having ht of 750 mm

Top, with MS Pipe Structure of Frame as per Architect/ Engineer Design or Selection and Back

and side Ply of table is also made up of 19mm Thick. Top of Table is 19mm thk ply with laminate

Finish Per Requirement and All internal & external Joints finished with teakwood beading Patti.

Common or front Part of Table is Sectationized with MS Perforated Sheet. All exposed and

Rupees TwentyFive Thousand

internal surfaces covered with Laminate Finish of approved shade & Complete as per detail

132 92.88 25093.79 NinetyThree Paise Sqm

drawings & as instructed by Architect/consultant/ Engineer In charge. Complete with all

SeventyNine Only

necessary hardware like nails, ss screws, table chain, Key board trey, TDS channel, adhesives

etc. Contractor has to provide all necessary cut outs for Electrical works & no extra payment

shall be made for it. All ply should follow IS

Sr. Quantities Item of Work Estimated Unit Total

In Rupees In Words

BOOK RACK (MODULAR) : Providing and Placing Book Rack - 1200mm X 400mm X 1850mm Rupees Fourteen Thousand

133 27.00 Material - 0.7 mm thick (+/- 0.07mm) CRCA for Top, Side and Shelf. Finish epoxy powder Coated 14802.16 Eight Hundred Two Paise Nos.

to the thickness of 50 micron. Sixteen Only

Supplying and providing reading chairs with PP arms with soft PU pads, Seat and back

upholstered with PU cushioned and MS powder coated frame and cantilever legs. Overall Rupees Four Thousand Eight

134 154.00 dimension 590 L x 600 W x 915 H (Or as specified) complete as directed by architect and 4878.3 Hundred SeventyEight Paise Nos.

product as per given specification. Complete as per architectural design and concept and Thirty Only

approved by Architect & Client.

CHAIR TYPE - 01 (CABIN MAIN CHAIR) :- Supplying and providing High Back Mesh office Chair

As per specification below:

-Metal frame seat made of Mesh fabric upholstery (foam base)

-Adjustable Head rest

-Fixed Arm rest Rupees Ten Thousand Seven

135 2.00 -Knee tilt mechanism 10738.07 Hundred ThirtyEight Paise Nos.

-360 swivel motion/ 100mm stroke gas Seven Only

-Nylon Star base

-Pushback mechanism & Comfy seating.

-Complete as per architectural design and concept and approved by Architect & Client.

Chair Type - 02 (Cabin Visitor Chair) : Supplying and providing Mid Back Mesh office Chair As

per specification below:

-Metal frame seat made of Mesh fabric upholstery (foam base)

-Center tilt mechanism Rupees Five Thousand Four

136 4.00 -100mm class 4 gas lift 5400.98 Hundred Paise NinetyEight Nos.

-PP Fixed Arm rest Only

-Nylon Star base/Twin wheel nylons casters

-Complete as per architectural design and concept and approved by Architect & Client.

Gang Chair ( 3 Seater) : Providing and Fixing 3 Seater (moulded foam seat and back In PU

upholstery ) Pero Cross Beam made of powder coated regular MS ERW tube having 8.0+/-0.03

cm x 4.0 +/- .03 cm x 0.2 +/- 0.014 cm size. Legs to be chrom plated made of rolled steel with

0.12 +/- 0.013 cm thinkness.Seat and Back Shell to be peforated made from cold rolled M.S. Rupees Eighteen Thousand

Sheet (DIN 1623 Part 1 ST -12 Grade), 0.14 +/- 0.013 cm thickness. The side Bar is made of Three Paise TwentyFive Only

chrome Plate solid steel 3.0 cm +/- 0.03cm x 1.2 cm +/- 0.03 cm with fluting and plastic inserts.

The Shell to be assembled on the cross beam with help of M8 Bolts.

Providing and Placing News paper Stand 600 W X 900 D X 900 H mm. To be made from pirme-

quality CRCA steel tubes and sheets for durability & longevity, and the reading top is made from

Rupees Seven Thousand One

high-quality pre-laminated MDF for a seamless finish and contemporary look. H-type cross

138 2.00 7160.65 Hundred Sixty Paise SixtyFive Nos.

bracings, paired with levelling bolts at the base, provide extraordinary strength and stability,

ensuring steady performance even on uneven floors.

Low Height Storage : Providing, making, fixing as per detail drawing made from 19 mm IS

BWP ply structure aand both side 1 mm thick laminate finish shall be of approved make &

shade and as per the detail drawing. All the edges of ply shall be covered with 1 mm thick

laminate finish Rate shall also inclusive of all necessary brass satin finish nickel plated/S.S

grade hardware like Hinges, locks,6"handle , 75 mm tower bolts, ball catches/Magnet, The rate

shall be in sqm of elevation area for all floors and at all heights including all costs complete as

per the Architectural drawings & instructions.Only the elevation area of the storage unit will be

measured and paid for. Item for 1 mm thick laminate fixing and polishing is included in this

item. Approval of all loose material (sample of materials to be used) & raw manufacturing to be

got approved in advance from EIC & Architect prior to the final production of the work. Rupees Ten Thousand Ninety

139 10.39 Manufacturing shall in parts or as whole as per the requirements & or assembled at site as per 10090.02 Sqm

the requirement and directed by EIC & Architect. All material to be used shall be as per the

drawings & confirm to the relevant detailed material specifications of this document. The work

shall be measured & paid in sqm The rates shall be inclusive of all wastages, material, labor,

taxes, transportation, loading, unloading, fixing in position, etc. complete to the satisfaction of

the Architect and EIC. The mock-up of 1 unit shall be approved from EIC and Architecture prior

to the final production.

Supplying and Placing Folding Wheel Chair with Overall dimension: (L) 790 x (W) 600 x

(H)870mm Frame structure Foldable frame structure is made of section 22x1.2mm A3 carbon

steel with chrome finish. Cross bar are made of A3 carbon steel with section 25.4 x 1.2mm. Rear

wheel 24 inch Solid mag wheels with alloy in the rim Hand rim Integrated hand rim provide to

drive the wheel chair of section 16x1.2mm A3 carbon steel with chrome finish Front wheel

inch HUB made of PA polymer and outer with solid rubber Arm rest PU molded arm rest & base

is made of ABS for better arm support Calf rest & seat Leatherette strap for calf rest & Rupees TwentyThree

140 2.00 leatherette cushion for seat Footrest Adjustable alluminimum die cast foot rest with updown & 23230 Thousand Two Hundred Nos.

swivel type mechanism Push handle Handles are made of moulded rubber grip to push the Thirty Only

wheelchair Brakes Hand brakes are provided to lock the wheelchair at desired location. Foot

press Extended base with molded plastic for better grip Finish Anti rust chrome finish safe

working load 100kg.etc.complete as per drawings and design supplied by architect and

instruction given by authority and E.I.C.

Total of Furniture work (C)

Sr. Quantities Item of Work Estimated Unit Total

In Rupees In Words

Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) both are of

ISI marked 1.1 KV grade FRLS PVC insulated multi strand copper wires up to 10 mtr length , in

below type of pipe erected with 6A Modular type switch / bell push & accessories and earth

continuity of following type, erected on PVC / Metallic/Wooden box, single mounting base

Rupees Four Hundred

frame covered with textured/metallic/white front plate modules erected on / in wall / ceiling

141 121.00 485.81 EightyFive Paise EightyOne Pt.

as per pipe erected, with necessary Lamp holder/ceiling rose / H.D.Connector as directed.

(f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling

complete Cat-III

Point wiring for secondary light point with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (green)

both are of ISI marked 1.1 KV grade FRLS PVC insulated multi strand copper wires, in below

type of pipe to be erected complete with earth continuity and necessary connection with

primary light with accessories erected on Metal / PVC / wooden box covered with 3 mm thick

Rupees One Hundred

142 145.00 PC(Polycarbonate) / Acrylic sheet for open / concealed wiring. with necessary Lamp holder / 167.66 Pt.

SixtySeven Paise SixtySix Only

ceiling rose / H.D.Connector as directed.

(f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling

complete Cat-III

Point wiring for Two Way Controlled Light Point with 2-1.5 sq.mm & earth wire of 1.5 sq.mm

(green) both are of .ISI marked 1.1 KV grade FRLS PVC insulated multi strand copper wires

erected in below type of pipe with 6A Modular type switches and following type of accessories

erected on PVC / Metallic/Wooden box, single mounting base frame covered with textured /

Rupees Six Hundred Three

143 3.00 metallic/white front plate modules erected on / in wall / ceiling as per pipe erected. with 603.98 Pt.

Paise NinetyEight Only

necessary batten/angle holder or ceiling rose or H.D.Connector as directed.

(f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling

Point wiring for FAN with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) both are of .ISI

marked 1.1 KV Grade FRLS PVC insulated multi strand copper wires up to 10 mtr length, in

below type of pipe erected with 6A Modular type switch and hum free EME step type

electronic fan regulator mounted and accessories with earth continuity of following type

Rupees Six Hundred

erected on PVC / Metallic/Wooden box, single mounting base frame covered with

144 54.00 674.68 SeventyFour Paise SixtyEight Pt.

textured/metallic/white front plate modules erected on / in wall / ceiling as per pipe erected.

with necessary ceiling rose / H.D.Connector as directed.

(f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling

complete Cat-III

Point wiring for Individual Plug with & earth wire of 1.5 sq.mm (Green) both are of ISI marked

1.1 KV grade FRLS PVC insulated multi strand copper wires up to 10 mtr length, in below type of

pipe erected complete with Modular type switch & 5 pin Plug erected on PVC /

Metallic/Wooden box covered with appropriate front plate modules erected on / in wall /

ceiling as per pipe erected with following type of accessories. Rupees Five Hundred Ten

[I] For 6A Plug and 6 a switch with 2-1.5 sq.mm Cu. Wire from nearby switchboard/mcb db Paise Five Only

(f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling

complete Cat-III

Point wiring for Individual Plug with & earth wire of 1.5 sq.mm (Green) both are of ISI marked

1.1 KV grade FRLS PVC insulated multi strand copper wires up to 10 mtr length, in below type of

pipe erected complete with Modular type switch & 5 pin Plug erected on PVC /

Metallic/Wooden box covered with appropriate front plate modules erected on / in wall / Rupees Seven Hundred

146 9.00 ceiling as per pipe erected with following type of accessories 745.38 FourtyFive Paise ThirtyEight Pt.

[II] For 16A Plug and 16 amp switch with 2-2.5 sq.mm Cu. Wire from mcb db board. Only

(f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling

complete Cat-III

Point wiring for Individual Plug with & earth wire of 1.5 sq.mm (Green) both are of ISI marked

1.1 KV grade FRLS PVC insulated multi strand copper wires up to 10 mtr length, in below type of

pipe erected complete with Modular type switch & 5 pin Plug erected on PVC /

Metallic/Wooden box covered with appropriate front plate modules erected on / in wall /

Rupees Eight Hundred

ceiling as per pipe erected with following type of accessories

147 6.00 871.63 SeventyOne Paise SixtyThree Pt.

[III] For 16A Plug and 16 amp switch with 2-4 sq.mm Cu. Wire with 2.5 sq.mm ( green)

earthing wire from mcb d b board..

(f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling

complete Cat-III

Point wiring for on board Looped Plug with 6A Modular type switch & 5 pin socket erected on

Rupees Two Hundred

PVC / Metallic/Wooden box, single mounting base frame covered with textured /

148 32.00 257.55 FiftySeven Paise FiftyFive Pt.

metallic/white front plate modules erected on / in wall / ceiling with following type

accessories. Cat-III

Providing following type of Modular Type Accessories mounted with PVC / metallic/Wooden

box, single mounting base frame covered with textured / metallic/white front plate , modules

Rupees One Hundred Sixty

149 2.00 erected with necessary connections as per site situation directed by Engineer In charge. 160.59 Ea.

Paise FiftyNine Only

(4) TV Co-axial Socket outlet Cat.III

Providing following type of Modular Type Accessories mounted with PVC / metallic/Wooden

box, single mounting base frame covered with textured / metallic/white front plate , modules

Rupees TwentyFive Paise

150 50.00 erected with necessary connections as per site situation directed by Engineer In charge. 25.25 Ea.

TwentyFive Only

(7) Blank Plate Single Cat.III

Sr. Quantities Item of Work Estimated Unit Total

In Rupees In Words

Providing & erecting Switch board for Computer or electric apparatus consisting of following

modular type accessories mounted with PVC / Metallic concealed/open box with single

mounting base frame covered with textured/metallic /white front plate,modules erected with

necessary connections as directed Rupees One Thousand One

151 23.00 1 no. 6A/16A universal plug-switch combined. 1133.22 Hundred ThirtyThree Paise Ea.

3 nos. 6A Switch TwentyTwo Only

3 nos. 6A 5 pin Plug For

Modular Type Accessories

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be

erected on/in wall or ceiling erected with necessary PVC fittings & Junction boxes fixed with

Rupees ThirtyThree Paise

152 800.00 adhesive solution & Clamps with following dia of pipes, in approved manner as directed. 33.33 Mtr.

ThirtyThree Only

Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper

conductor wire in following type of pipe to be erected concealed in /flushed on wall/ceiling,

with 1.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth Rupees SixtyTwo Paise

continuity of following size SixtyTwo Only

(A) with medium class Rigid PVC pipe and accessories

(a) 2 wire 1.5 sq. mm

Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper

conductor wire in following type of pipe to be erected concealed in /flushed on wall/ceiling,

with 1.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth Rupees EightyTwo Paise

continuity of following size EightyTwo Only

(A) With medium class Rigid PVC pipe and accessories

(b) 2 wire 2.5 sq. mm

providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper

conductor wire in following type of pipe to be erected in / on wall / ceiling with 2.5 sq. mm

copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of Rupees One Hundred Twelve

following size Paise Eleven Only

(A) with medium class Rigid PVC pipe and accessories

(a) 2 wire 4 sq. mm

Lighting Fixtures ,Fan & other items : Providing and erecting decorative wall bracket fittings

complete with LED lamp and rust free fittings components mounted in chrome finish housing Rupees One Thousand Seven

156 20.00 with holder ,clear/opaque glass diffuser complete erected with lead wires with minimum 15 1712.96 Hundred Twelve Paise Ea.

wattage capacity as per instruction engineer incharge/architect/authority .cat-III NinetySix Only

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt

assembled on single MCPCB, with housing used as a heat sink shall be made of thick sheet Steel

conforming to IS: 513/CRCA/aluminium pressure die cast powder coated and high U.V. &

corrosion resistance with diffuser housed in aluminium casted body with company mark/name

160V to 270V,Power Factor more than 0.95, THD < 15 %,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt , Rupees Four Hundred

157 15.00 LED driver efficiency > 85 % 427.23 TwentySeven Paise Ea.

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description have shown ranges of TwentyThree Only

Wattage capacity of LED fittings.The Engineer incharge may select any wattage capacity

between the ranges shown.)

(A) Square/ Circular shaped Surface/Recessed Mount Downlight with provision for spring

loaded mounting clips complete.IP20

(ii) 11-15 watts, Surge-2 KV KV cat-III

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt

assembled on single MCPCB, with housing used as a heat sink shall be made of thick sheet Steel

conforming to IS: 513/CRCA/aluminium pressure die cast powder coated and high U.V. &

corrosion resistance with diffuser housed in aluminium casted body with company mark/name

160V to 270V,Power Factor more than 0.95, THD < 15 %,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt , Rupees Five Hundred

158 221.00 LED driver efficiency > 85 % 589.84 EightyNine Paise EightyFour Ea.

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description have shown ranges of Only

Wattage capacity of LED fittings.The Engineer incharge may select any wattage capacity

between the ranges shown.)

(A) Square/ Circular shaped Surface/Recessed Mount Downlight with provision for spring

loaded mounting clips complete.IP20

(iii) 16-20 watts, Surge-2 KV cat-III

Supplying and erecting LED street light / Flood light fittings with High power White LEDs

wattage of 3 Watt and above assembled on single MCPCB, efficiency more than 130 lm/w and

corrosion free High pressure die cast aluminum housing with smooth finish powder coated and

heat sink extruded aluminium with diffuser and Polycarbonate optics/ lenses, with toughened

glass with company mark/name engraved or embossed 160 to 270 V,Power Factor more than

0.95, THD < 10 %, CCT 3000 K to 5700K,Uniformity ratio >0.45, Luminaire efficacy> 100 Rupees Six Thousand Five

159 41.00 lumens/watt . LED driver efficiency > 85 %.( fittings required LM-79 & LM-80 6566.01 Hundred SixtySix Paise One Ea.

certificates)(NOTE: Below description have shown ranges of Wattage capacity of LED Only

fittings.The Engineer incharge may select any wattage capacity between the ranges shown.)

(A) Street Light (IP-65), Surge protection -4KV integral and ,Light must have 440VAC line supply

with over-voltage protection. (iv) above 90 to 120 watts Cat-lll

Sr. Quantities Item of Work Estimated Unit Total

In Rupees In Words

Supplying and erecting LED street light / Flood light fittings with High power White LEDs

wattage of 3 Watt and above assembled on single MCPCB, efficiency more than 130 lm/w and

corrosion free High pressure die cast aluminum housing with smooth finish powder coated and

heat sink extruded aluminium with diffuser and Polycarbonate optics/ lenses, with toughened

glass with company mark/name engraved or embossed 160 to 270 V,Power Factor more than

Rupees Eight Thousand Four

0.95, THD < 10 %, CCT 3000 K to 5700K,Uniformity ratio >0.45, Luminaire efficacy>

160 9.00 8453.7 Hundred FiftyThree Paise Ea.

lumens/watt . LED driver efficiency > 85 %.( fittings required LM-79 & LM-80

certificates)(NOTE: Below description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage capacity between the ranges shown.) (B)

Flood Light (IP-65), Surge protection -4KV integral and ,Light must have 440VAC line supply

with over-voltage protection.(v) above 120 to 160 watts Cat-lll

Supply, Installation, Testing and Commissioning of suitable sweep, BEE 5 Star rated, Ceiling fan

with Brush Less Direct Current (BLDC) permanent ferrite magnet Motor, class of insulation: B,

Rust free 3 nos.Aluminium blades, 2 nos. canopies, shackle kit with earthing provision, copper

winding, Power factor not < 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum

215 CMM, 350 RPM,230v (tolerance as per IS : 374-2019), THD < 10%, with remote unit for Rupees Two Thousand Eight

161 54.00 Speed Control and all remaining accessories including safety pin, nut bolts, washers, 2885.57 Hundred EightyFive Paise Ea.

temperature rise = 75 degree C (Max.), suitable for 140 to 285 Voltage and rectifier circuit with FiftySeven Only

surge, over current and overload protection , 50 Hz, Single phase AC Supply, earthing etc.

Complete as required.[ Make shall be approved by Engineer in Charge] (B) 1200 mm Sweep

Supplying and erecting 19 / 20 mm. nominal bore Medium Class M.S. Pipe down rod erected

Rupees One Hundred Eight

162 2.00 duly painted for fan complete with proper insulation without leakage and earthing. 108.07 Mtr.

Paise Seven Only

Supplying & erecting fan hook box of 10 mm M.S. round bar bounded to the RCC bars up to

50mm length each side and pierced through a 16 Gauge M.S. box / Heavy Duty PVC box Rupees One Hundred Eight

complete erected concealed in Ceiling with necessary finishing. Paise Seven Only

Providing 2.5mm.thick laminated acrylic sheet to cover the fan hook or Fan box. Rupees Eighteen Paise

Supplying & erecting approved make low noise decorative exhaust fan having square frame Rupees One Thousand Seven

165 13.00 ABS body with inbuilt lowers & square frame.For 200mm with 1350 RPM cat-ii 1703.87 Hundred Three Paise Ea.

EightySeven Only

Street Light poles : Supplying & erecting Galvanized M.S pipe post “B” class 88.9 mm O.D

Rupees Three Thousand Two

mtr. Long duly painted with two coats of aluminium paint complete with metallic base plate of

166 41.00 3225.94 Hundred TwentyFive Paise Ea.

300 mm x 300 mm x 4mm thick for using as a compound light pole with approx. weight 32 Kg.

NinetyFour Only

Providing 1:2:4 cement concrete foundation & 70 % PCC from bottom including excavation for

the pole of size 45 x 45 x 100 cm. Deep in below ground level with plinth of 45 cm x 45 cm (or

Rupees Eight Hundred Nine

167 41.00 cm dia x 45 cm) high upper ground level with necessary curing and finishing in approved 809.01 Ea.

( for 4 & 6 mtr pole)

Supplying & erecting approved make SMC press moulded composite FRP. loop-in, loop-out

approx. 2mm thick box complete with Bakelite connector strip 5way(3P+N+E),DIN rail for

mounting mob & hinged doors as per requirement having locking arrangements with mounting Rupees Eight Hundred

clamp with nuts, bolts & washers suitable for erection on pole with cable clamps& earth bolt of NinetyEight Paise Ninety Only

following size of box. (A) 300mm x 200mm x 100mm [deep]

Providing and erecting street light pole bracket comprising main B Class GI pipe of

cm/require outside dia. complete with suitable B Class G.I sleeve tubing of approx.

45cms.length and suitable for 76.5 mm / 80mm. / require size pole top having sufficient

fasteners for fixing the brackets and having spread of 1 mtr. length with suitable rise as per site Rupees Six Hundred Fourteen

condition & suitable welded stiffener reducer and nipple with check nut complete painted with Paise Eight Only

one coat of Red oxide / PU base primer and two coats of Aluminium / PU paint. paint with

following nos of arms. [a] Single Arm bracket 1 Mtr

Providing and erecting street light pole bracket comprising main B Class GI pipe of

cm/require outside dia. complete with suitable B Class G.I sleeve tubing of approx.

45cms.length and suitable for 76.5 mm / 80mm. / require size pole top having sufficient

Rupees Eight Hundred

fasteners for fixing the brackets and having spread of 1 mtr. length with suitable rise as per site

170 6.00 829.21 TwentyNine Paise TwentyOne Ea.

condition & suitable welded stiffener reducer and nipple with check nut complete painted with

one coat of Red oxide / PU base primer and two coats of Aluminium / PU paint. paint with

following nos of arms. [B] Double Arm Bracket 1 Mtr

Supplying & erecting approved make Digital time switch having lithium cell 6 years operative

and operate battery backup 1 channel day clock with 14 memory programme, suitable to

operate on 240V + 5%, 16A with, floating contacts Minimum switching setup time 1 minimum & Rupees Three Thousand One

171 1.00 LCD display. Also comprised permanent ON/OFF switching. Programming switches & housed in 3168.37 Hundred SixtyEight Paise Ea.

fire proof thermoplastic enclosure & transparent cover erected as required with necessary ThirtySeven Only

connection erected as directed.

Supplying & erecting power contactor ,AC3 duty for time switch complete erected as per

Rupees Two Thousand Seven

direction Cat III (D) 4 pole 440V 40 Amp.

172 1.00 2782.55 Hundred EightyTwo Paise Ea.

Panel & Switchgear : Providing and erecting Approved make Four pole moulded case circuit

breaker having breaking capacity ICU of 25 KA. at 415 V,having normal current rating up to 25 A

Rupees Six Thousand One

to 100A. with Fixed thermal & magnetic release suitable to work on A.C. supply 50 c/s. with all

173 21.00 6173.12 Hundred SeventyThree Paise Ea.

internal connections, spreader tinned copper & complete erected in existing 16 G.M.S. housing.

ICS=100% of ICU only Cat III

Sr. Quantities Item of Work Estimated Unit Total

In Rupees In Words

Providing and erecting Approved make Four pole moulded case circuit breaker having

breaking capacity ICU of 35 KA. at 415 V. having Normal current rating 200A.with variable Rupees Sixteen Thousand

174 2.00 Thermal & magnetic release suitable to work on A.C.supply 50 c/s. with all internal connections, 16221.61 Two Hundred TwentyOne Ea.

spreader tinned copper & complete erected in existing 16 G.M.S.housing. ICS=100% of ICU Paise SixtyOne Only

Providing and erecting Approved make Four pole moulded case circuit breaker having breaking

capacity ICU of 35 KA. and above at 415 V . having normal current rating 250A. with variable Rupees Twenty Thousand

175 1.00 thermal & magnetic release suitable to work on A.C.supply 50 c/s. with all internal connections, 20946.39 Nine Hundred FourtySix Paise Ea.

spreader tinned copper & complete erected in existing 16 G.M.S. housing. Cat III ThirtyNine Only

PANEL MOUNTING BUSBARS : Supplying and erecting triple pole & neutral 440V/ 500V panel

mounting Aluminium Busbars with four equal Nos. of bus having current density not more than

0.8 Amp. / sq.mm (Rated current / cross section area) duly wrapped with colour insulating tape Rupees One Thousand

176 10.00 for phase sequence of following current carrying capacity, erected with necessary bus bar 1037.27 ThirtySeven Paise Rn.Mtr

supports /insulators, main cable socket to each busbar,erected in existing cubical panel with TwentySeven Only

necessary connections. (B) Suitable for 200 Amp. capacity

Providing and erecting Approved make Earth fault Relay suitable to mount with inter

connection suitable to following size of moulded case circuit breaker having CT ratio & MCCB Rupees Five Thousand Four

177 1.00 rating as following along with shunt trip 220V AC. with all internal connections & complete 5415.62 Hundred Fifteen Paise Ea.

erected in existing M.S.housing. SixtyTwo Only

providing and erecting Miniature circuit breaker single pole 6A to 25A suitable to operate on

Rupees One Hundred Twelve

178 123.00 240 V A.C. system and having breaking capacity 10 KA to be erected in existing box. confirming 112.11 Ea.

Paise Eleven Only

to IS 8828/1996 with ISI Mark Cat.III

Providing & erecting 240 V MCB double pole switch for motor & inductive load (C Curve) Rupees Two Hundred

179 44.00 having 10 KA breaking capacity & confirms to IS : 8828 in existing box having following capacity 299.97 NinetyNine Paise Ea.

(A) 6 to 32 Amp. NinetySeven Only

Providing and erecting 415 Volt MCB four pole motor & inductive load(c Curve) having 10 KA

Rupees Six Hundred

180 1.00 Breaking capacity and confirms to IS : 8828 in existing metal box having following capacity. (B) 668.62 Ea.

SixtyEight Paise SixtyTwo Only

40 Amp. Cat III

Providing and erecting 415 Volt MCB four pole motor & inductive load(c Curve) having 10 KA

Rupees Seven Hundred

181 3.00 Breaking capacity and confirms to IS : 8828 in existing metal box having following capacity. (C) 737.30 Ea.

ThirtySeven Paise Thirty Only

63 Amp. Cat- III

Providing & erecting 415 V MCB three Pole for Motor & Inductive Load (C Curve) having 10KA Rupees Six Hundred

182 2.00 breaking capacity & confirms to IS :8828 in existing box having following capacity (b)40 Amp. 647.41 FourtySeven Paise FourtyOne Ea.

Providing & erecting 415 V MCB three Pole for Motor & Inductive Load (C Curve) having 10KA

Rupees Seven Hundred

183 4.00 breaking capacity & confirms to IS :8828 in existing box having following capacity (c)63 Amp. 716.09 Ea.

Sixteen Paise Nine Only

providing and erecting Approved make RCCBs conforming to IS: 12640 and having sensitivity of

30 mA and Short Circuit withstand capacity of 10 KA and suitable for operation on single phase

240 V,50Hz. having characteristic of quick action & tripping with all advance feature & do not Rupees One Thousand Nine

184 3.00 1969.50 Hundred SixtyNine Paise Fifty Ea.

incorporate any electronic component. for following Max. rating erected as directed

(i) 25 Amps.DP Cat. III Only

providing and erecting Approved make RCCBs conforming to IS: 12640 and having sensitivity of

30 mA and Short Circuit withstand capacity of 10 KA and suitable for operation on single phase

240 V,50Hz. having characteristic of quick action & tripping with all advance feature & do not Rupees Two Thousand Two

185 10.00 incorporate any electronic component. for following Max. rating erected as directed 2235.13 Hundred ThirtyFive Paise Ea.

(ii) 40Amps. DP Cat. III Thirteen Only

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface

mounted fitted with busbar, neutral link, earth bar and DIN rail, Conforms to IS 8623-1 & 3, IEC

61439-1 & 3 without MCB to house appropriate nos. of MCBs.(The DBs should be used of same

Rupees Two Thousand Nine

company of MCB to be used) suitable for

186 1.00 2913.85 Hundred Thirteen Paise Ea.

(B) three phase incoming and single phase horizontal type outgoing Per phase isolation type

EightyFive Only

(b) sheet steel double door

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface

mounted fitted with busbar, neutral link, earth bar and DIN rail, Conforms to IS 8623-1 & 3, IEC

61439-1 & 3 without MCB to house appropriate nos. of MCBs.(The DBs should be used of same

company of MCB to be used) suitable for Rupees Three Thousand Four

187 1.00 3412.79 Hundred Twelve Paise Ea.

(B) three phase incoming and single phase horizontal type outgoing Per phase isolation type

(PPI) SeventyNine Only

(b) sheet steel double door

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface

mounted fitted with busbar, neutral link, earth bar and DIN rail, Conforms to IS 8623-1 & 3, IEC

61439-1 & 3 without MCB to house appropriate nos. of MCBs.(The DBs should be used of same

Rupees Three Thousand Eight

company of MCB to be used) suitable for

188 1.00 3874.36 Hundred SeventyFour Paise Ea.

(B) three phase incoming and single phase horizontal type outgoing Per phase isolation type

(b) sheet steel double door

Sr. Quantities Item of Work Estimated Unit Total

In Rupees In Words

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface

mounted fitted with busbar, neutral link, earth bar and DIN rail, Conforms to IS 8623-1 & 3, IEC

61439-1 & 3 without MCB to house appropriate nos. of MCBs.(The DBs should be used of same

Rupees Four Thousand Six

company of MCB to be used) suitable for

189 1.00 4666.20 Hundred SixtySix Paise Ea.

(B) three phase incoming and single phase horizontal type outgoing Per phase isolation type

(b) sheet steel double door

Providing and erecting Sheet Steel powder coated Vertical MCB distribution board (VTPN) -

flush / surface mounted double door (IP54) fitted with copper insulated busbar, isolated neutral

Rupees Nine Thousand Nine

bar, earth bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3, suitable for 250 AMP

190 1.00 9921.23 Hundred TwentyOne Paise Ea.

TPN MCCB + RCCB as incomer and three phase outgoing as per following .(The DBs should be

TwentyThree Only

used of same company of MCB to be used) (B)6 way outgoing

Earthing : Supplying & erecting in earthpit of minimum bore dia. 225mm size approved make

Safe Earthing Electrode consisting Pipe-in-Pipe Technology as per IS 3043-1987 made of

corrosion free hot dipped G.I.Pipes having Outer pipe dia of 80 mm having 80-200 Micron

galvanising, Inner pipe dia of 40 mm having 200-250 Micron galvanising, connection terminal

dia of 14 mm with constant ohmic value surrounded by highly conductive compound with

high charge dissipation suitable for following type of applications with chamber and heavy duty

cover (A)(approved make OEM has to submit test certificate including value of earth resistance

of installation duly stamped and signed by agency and officer Incharge has to ensure the value

of earthing resistane mentioned in test Certificate) & having back filling compound of (B) Inner Rupees Ten Thousand Five

191 9.00 chemical (CCM Compound)- Resistivity:- 0.2 ohm / meter testing as per IEC 62561-2017, 10593.89 Hundred NinetyThree Paise Ea.

Voltage drop:- < 1 volt at no load & dry form, Sulphar content:- <2%(C) Back fill Compound :- EightyNine Only

Earthing compound should be capable to retain moisture for long time Necessary test report

must be submitted by Agency.(c) For Electrical Installation covering Transformer Neutrals,

Lightning arrester Earthing, A.C.Plant & Sensitive Computer System(like Automation, SCADA) i.e

independent Earthing in normal soil.

Length of Pipe : 3.00 mtrs

Back filling Compound :2 nos Bags of 25 Kg.

Cupboards : Providing & erecting weather proof, dust & vermin proof, floor mounted front

operated indoor type cubical panel board necessary IP-42 and above protection as per

approval from engineer incharge made from 14 SWG thick CRC M.S. sheet for outer body &

doors, 16 SWG thick CRC M.S.sheet for internal partitions with necessary accesories

supporting angles/ flats channel including cutting, bending, drilling, welding, riveting with

internal partitions & cable alley as per requirements & instruction of engineer-in-charge with

erection of supplied switch gears, BUSBARS, suitable size of inter connecting PVC copper wire / Rupees Fourteen Thousand

192 10.00 copper-aluminium strips, rubber grommets, rib, bakelite control fuses/MCB for measuring 14902.55 Nine Hundred Two Paise Sq.Mtr

instruments, earth bus & earth bolts, foundation flange - bolts-base Plates, sufficient nos. of FiftyFive Only

hinged doors, handles with locking arrangement and rubber gasket,heavy duty end terminal

connection,danger notice board,necessary ventilation,earthing strip complete. The Panel shall

be painted with epoxy powder coating. (B) The standard companies switch gear shall be used

and only manufacturers at CPRI approved factory (i) with 350mm depth

Providing and erecting ,Fabricating the box type items made from M.S. Sheet with A.I. supports,

wings, doors, handles other hardware materials as per requirement design with finishing by Rupees One Hundred Eighty

three tank powder coating processed inside and outside painted, erected as directed including Paise SeventyNine Only

minor civil work.

Cables : Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium

conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of Rupees Two Hundred Twenty

following size of cables (B) 3 1/2 core 35 Sq. mm ( 16 Sq. mm 1/2 core) Paise Eighteen Only

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium

Rupees Two Hundred

conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of

195 66.00 284.82 EightyFour Paise EightyTwo Mtr.

following size of cables (C) 3 1/2 core 50 Sq. mm ( 25 Sq.1/2 mm core)

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium

Rupees Three Hundred

conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of

196 55.00 378.75 SeventyEight Paise Mtr.

following size of cables (D) 3 1/2 core 70 Sq. mm ( 35 Sq. mm 1/2 core)

SeventyFive Only

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium

conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of Rupees Five Hundred Fourty

following size of cables (F) 3 1/2 core 120 Sq. mm ( 70 Sq. mm 1/2 core) Paise ThirtyFive Only

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand Aluminium

Rupees One Hundred

conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of

198 44.00 153.52 FiftyThree Paise FiftyTwo Mtr.

following size of cables (A) 4 core 16 Sq. mm

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand Aluminium

conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of Rupees One Hundred Ninety

following size of cables (B) 4 core 25 Sq. mm Paise EightyNine Only

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand / Solid Copper

conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe at Rupees Three Hundred

road crossing or floor of following size of cables. SixtyFour Paise SixtyOne Only

(B) 4 core 4 Sq. mm

Sr. Quantities Item of Work Estimated Unit Total

In Rupees In Words

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand / Solid Copper

conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe at Rupees Five Hundred Ten

road crossing or floor of following size of cables. Paise Five Only

(C) 4 core 6 Sq. mm

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper conductor

for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe at road Rupees Six Hundred

crossing or floor of following size of cables. SeventySix Paise Seventy Only

(A) 4 core 10 Sq. mm

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC

insulated armoured cable complete with out going tails, insulating tape etc for following size of Rupees ThirtyThree Paise

cables. (A) 2 to 4 core 2.5 / 4 Sq. mm ThirtyThree Only

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC

Rupees ThirtyEight Paise

204 29.00 insulated armoured cable complete with out going tails, insulating tape etc for following size of 38.38 Ea.

ThirtyEight Only

cables. (B) 2 to 4 core 6 Sq. mm

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC

Rupees ThirtyEight Paise

205 7.00 insulated armoured cable complete with out going tails, insulating tape etc for following size of 38.38 Ea.

ThirtyEight Only

cables. (C) 2 to 4 core 10 Sq. mm

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC

Rupees FourtySeven Paise

206 2.00 insulated armoured cable complete with out going tails, insulating tape etc for following size of 47.47 Ea.

FourtySeven Only

cables. (D) 2 to 4 core 16 Sq. mm

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC

Rupees FiftyOne Paise

207 7.00 insulated armoured cable complete with out going tails, insulating tape etc for following size of 51.51 Ea.

cables. (E) 2 to 4 core 25 Sq. mm

Providing and, fixing heavy duty flange type brass double compression type cable gland with

rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc Rupees SeventyFive Paise

for following size of cables. SeventyFive Only

(B) 3 & 1/2 core 35/50 Sq. mm

Providing and, fixing heavy duty flange type brass double compression type cable gland with

rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc Rupees One Hundred Three

for following size of cables. Paise Two Only

(C) 3 & 1/2 core 70 Sq. mm

Providing and, fixing heavy duty flange type brass double compression type cable gland with

rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc Rupees One Hundred Fourty

for following size of cables. Paise ThirtyNine Only

(E) 3 & 1/2 core 120 Sq. mm

Solder less crimping type Aluminium lugs conforming to IS suitable for cable of following size

evenly crimped with high pressure tool & connected to switchgear terminals with Rupees Thirteen Paise

brass/cadmium plated nut bolts in an approved manner. Thirteen Only

Solder less crimping type Aluminium lugs conforming to IS suitable for cable of following size

evenly crimped with high pressure tool & connected to switchgear terminals with Rupees Fifteen Paise Fifteen

brass/cadmium plated nut bolts in an approved manner. Only

Solder less crimping type Aluminium lugs conforming to IS suitable for cable of following size

evenly crimped with high pressure tool & connected to switchgear terminals with Rupees Twenty Paise Twenty

brass/cadmium plated nut bolts in an approved manner. Only

Solder less crimping type Aluminium lugs conforming to IS suitable for cable of following size

evenly crimped with high pressure tool & connected to switchgear terminals with Rupees TwentyFive Paise

brass/cadmium plated nut bolts in an approved manner. TwentyFive Only

Solder less crimping type Aluminium lugs conforming to IS suitable for cable of following size

evenly crimped with high pressure tool & connected to switchgear terminals with Rupees FourtyFive Paise

brass/cadmium plated nut bolts in an approved manner. FourtyFive Only

Solder less crimping type Copper lugs conforming to IS suitable for cable of following size evenly

crimped with high pressure tool & connected to switchgear terminals with brass/cadmium

216 141.00 8.08 Rupees Eight Paise Eight Only Ea.

plated nut bolts in an approved manner.

Danger Sign boards : Providing and erecting metallic vitrified danger notice board as per

Rupees SixtyNine Paise

217 2.00 language suggested by engineer incharge for MEDIUM VOLTAGE installation to be erected as 69.69 Ea.

Providing & erecting Medium Voltage Danger Notice Board sticker as per language suggested Rupees TwentySix Paise

by engineer incharge of standard size as per IS-2551 TwentySix Only

Miscellaneous : Providing & laying. R.C.C. Hume pipe for cable to be laid 90 cm. below ground

Rupees Three Hundred

across the road crossing or on floor with necessary material in an approved manner and making

219 80.00 343.40 FourtyThree Paise Fourty Mtr.

the ground as per original. (C) 300 mm dia

Providing & laying approved make Double walled corrugated pipes (DWC) of

polyethylene(conforming to IS 14930 II )with necessary connecting accessories of same

Rupees NinetyFive Paise

220 150.00 material at required depth in existing trench for laying of cable. below ground / road surface 95.95 Mtr.

NinetyFive Only

for enclosing cable

(C))90 mm outer dia

Providing & laying approved make Double walled corrugated pipes (DWC) of

polyethylene(conforming to IS 14930 II )with necessary connecting accessories of same Rupees One Hundred

221 500.00 material at required depth in existing trench for laying of cable. below ground / road surface 137.36 ThirtySeven Paise ThirtySix Mtr.

for enclosing cable Only

(D)120 mm outer dia.

Meters & Panel Accessories : Supplying and erecting approved make panel mounting type

Rupees One Thousand Two

Digital Voltmeter having 3 digits LED display, 0 to 750 AC Volts range erected on existing panel

222 3.00 1275.63 Hundred SeventyFive Paise Ea.

board with all connection, wiring etc .with manufacturers calibration certificate.

SixtyThree Only

Sr. Quantities Item of Work Estimated Unit Total

In Rupees In Words

Supplying and erecting approved make panel mounting type Digital Ammeter having 3 digits

Rupees One Thousand Five

LED display, external CT operated, calibrated for 0 to 1000 Amps suitable to operate on 500 Volt

223 3.00 1558.43 Hundred FiftyEight Paise Ea.

AC , erected on existing panel board with all connection, wiring etc .with manufacturers

FourtyThree Only

calibration certificate.

Supplying and erecting Ammeter / Voltmeter selector switch for 3 phase AC Supply 500 V on Rupees Three Hundred

224 3.00 existing panel board with necessary connections. 317.14 Seventeen Paise Fourteen Ea.

Providing & erecting L.T. Current Transformer with bar primary 50/5 to 1000/5 ratio 15 VA Rupees Two Hundred

225 3.00 burden erected in existing CRCA box duly secured with insulating materials connected to the 274.72 SeventyFour Paise Ea.

meter SeventyTwo Only

Supplying and erecting approved make set of indicator lamps of LED type lamp, lens cover, Rupees FourtyThree Paise

Bakelite holder complete erected with necessary connections. FourtyThree Only

Miscellaneous : Providing and fixing printed instruction chart both in English and Gujarati and

Rupees One Hundred Thirty

227 1.00 duly framed with front glasses, for treatment of person suffering from Electric shock with 130.29 Ea.

Paise TwentyNine Only

minimum 50" diagonally size.

Providing pair of rubber hand gloves suitable for working on 11 KV/22 KV supply.

Rupees Two Hundred

Fourteen Paise Twelve Only

Supplying rubber matting of following thickness as per IS:15652/IEC 61111 Rupees One Thousand

229 8.00 (b)4mm 1027.17 TwentySeven Paise Sq.Mtr

Supplying stand first AID box with antiseptic cream, medicine for use on wounds due burn,

Rupees Two Hundred

crepe bandage, gauge bandage, medicated ready to use bandage (Band-aid) adhesive tape for

230 2.00 299.97 NinetyNine Paise Ea.

medicinal user, Scissors, anti-septic solution (Savlon or similar) etc. (All above contents shall be

NinetySeven Only

of standard makes)

Supplying FIRE bucket round bottom of 9 litres capacity made out of 24 gauge G.I. sheet with

extra handle at bottom duly painted white inside and Red out side with FIRE mark, filled with Rupees Two Hundred

dry-sand and kept on existing stand provided or hung on wall hook. Fourteen Paise Twelve Only

Wall hook 22 to 25 cms. projection for keeping fire buckets made out of 15 mm dia. M.S rod

232 4.00 60.60 Rupees Sixty Paise Sixty Only Ea.

grouted in wall to a depth of minimum 15 cms.

UPS : Supplying and erecting approved make online Un-interruptible Power Supply system

comprising flat cum-boost charger with IGBT base rectifier & Inverter & sealed maintenance

free SMF batteries. The charger having operating capacity for input 160-270V AC & inverter

having output 230V,50 Hz Ac with 0.8 load power factor with battery, over/under voltage Rupees Two Lakh Seventy

233 1.00 output with over load & short circuit protection equipment. The system housed in CRC sheet 270989.06 Thousand Nine Hundred Ea.

duly powder coated paint with following power backup.with MS painted batteries stand, 10% EightyNine Paise Six Only

Overload capacity for momentary load.

(I) 10 KVA 3 - phase with 1Hr Backup

LIGHTNING ARRESTER : SITC of Vertical Air Termination Solid aluminium with Base- 10 mm dia

and 1000 mm long. Air Termination Base tested for conditioning, Ageing Test & Lightning Rupees Nine Thousand Four

234 1.00 impulse current withstand test: 100 kA of 10/350µs waveform in an accredited Third party 9416.23 Hundred Sixteen Paise Ea.

laboratory as per 6.3 & 6.4 of IEC 62561-1 2017 protocol with MAST 34mm dia 3000 mm long- TwentyThree Only

Cold Galvanized

SITC of 8 mm dia solid Aluminium Conductor for roof top mesh grid and tested as per IEC

62561- 2 conducted in the Govt. accredited thirty party laboratory to meet the requirement of

IS/IEC 62305 with Required Accessories - Aluminium Holding clamp at every 1 mtr distance,

Aluminium/SS cross splicer at every crossing of Alu. conductor, Expansion piece with connectors

Rupees Two Hundred

at every 20 mtr distance, Aluminium straight Splicer to connect conductors. All Accessories

235 80.00 299.97 NinetyNine Paise Mtr.

should be tested as per IEC 62561-1 2018 Cl. 6.3 for conditioning & Ageing Test & 6.4 for

NinetySeven Only

Lightning impulse current withstand test: 100 kA of 10/350µs waveform(Ageing & Electrical test

) conducted in a sequence manner & tested in the Govt. accredited Third party laboratory to

meet the requirements of IS/IEC

SITC of 14.2 mm dia 3 mtr long Earth electrode of High tensile steel electrode with 250 micron

copper bonding & 1 bag of Carbon fill Based environment friendly backfill tested as per IEC

Rupees Five Thousand Nine

62561-7 in NABL accredited Laboratory and suitable stainless Steel double sided clamp. Eco

236 2.00 5992.33 Hundred NinetyTwo Paise Per Set

Friendly rust proof heavy duty weather proof Polyethylene Earth Pit Chamber with following

ThirtyThree Only

dimensions :254 mm dia (top), 330 mm dia (bottom) & 260 mm (height).

SPLIT AIR-CONDITIONERS : Providing and erecting Inverter based approved make split air-

conditioning unit consisting of condensing unit with variable speed fan motor, inverter type

hermetically sealed rotary compressor with accessories etc. duly connected separately erected

Rupees FiftyFive Thousand

evaporating unit and blower motor with its accessories by means of extra supplied proper

237 2.00 55189.43 One Hundred EightyNine Ea.

insulated copper tubing,drain PVC pipes suitable for ( cost includes Eco Friendly green gas

Paise FourtyThree Only

charging and 15A plug top & Remote Control & MS Stand) with necessary core cutting.(2)For

ISEER Range (KWH/KWH)(4.0 to 4.49)(B) for 1.5 ton capacity- Premium Cat.

Providing and erecting Inverter based approved make split air-conditioning unit consisting of

condensing unit with variable speed fan motor, inverter type hermetically sealed rotary

compressor with accessories etc. duly connected separately erected evaporating unit and Rupees SeventyTwo

blower motor with its accessories by means of extra supplied proper insulated copper Thousand Three Hundred

tubing,drain PVC pipes suitable for ( cost includes Eco Friendly green gas charging and 15A plug EightyOne Paise SixtyFive

top & Remote Control & MS Stand) with necessary core cutting.(2)For ISEER Range Only

(KWH/KWH)(4.0 to 4.49)(C) for 1.7 to 2 ton capacity-Premium Cat.

Sr. Quantities Item of Work Estimated Unit Total

In Rupees In Words

WATER COOLERS : Providing and erecting water cooler having storage capacity 25Ltr. &

cooling capacity 10 Ltr.per hour @ an ambient temp of 45˚ C. The outlet temp. of the water

should drop by 15˚ C within a hour, The water cooler should be comprising of hermetically Rupees TwentySeven

239 2.00 sealed compressor, fan motor, condensing unit, water tank surrounded by evaporating coil, 27270.00 Thousand Two Hundred Ea.

thermostats, relay etc. complete with necessary inlet & outlet connection. The body of water Seventy Only

cooler will be made from Stainless Steel.

Supplying & erecting 5 stage single reverse osmosis water purification system with M.S.

powder coated frame, prefilter housing with 'O' ring presediment filter GAC filter, carbon filter

Rupees Fifteen Thousand Six

suitable buster DC pump capacity 80 psi, mention with 40 psi inline type post carbon filter auto

240 2.00 15620.66 Hundred Twenty Paise Ea.

low & high pressure switches with following size of storage tank & LPH capacity & erected as

directed [B] 25 Ltr / Hr with 30 Ltr. Storage Tank

LIASONING WORK : Providing Power Connection Requirement of 80 KW Including

Rupees Eighty Thousand Eight

241 1.00 Electrical Connect Power Charges , Inspector Approval . Liaisoning work for additional load 80800.00 Job.

for requirement, electrical power connection charges and inspector approval for power

Total of Electrical Work (D)

Data and Networking Rupees Two Hundred

242 22.00 SITC of ABS back box 294.92 NinetyFour Paise NinetyTwo Ea

[Approved by Competent Authority i.e. not Below the rank of Executive Engineer ] Only

SITC of Face Plate - Single (Keystone Jack,square) Rupees Ninety Paise Ninety

[Approved by Competent Authority i.e. not Below the rank of Executive Engineer ] Only

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be

erected on/in wall or ceiling erected with necessary PVC fittings & Junction boxes fixed with Rupees ThirtyThree Paise

adhesive solution & Clamps with following dia of pipes, in approved manner as directed ThirtyThree Only

SITC of CAT6 UTP 23AWG Solid: Per Meter Rupees FourtyThree Paise

[Approved by Competent Authority i.e. not Below the rank of Executive Engineer FourtyThree Only

Supply, installation, testing, and commissioning (SITC) of a 24U, 19-inch standard floor-mount

rack. The rack must be made of mild steel with a powder-coated finish and include lockable Rupees Twenty Thousand

front and rear doors (front door typically glass or perforated, rear door perforated), lockable Two Hundred Only

and removable side panels, and a welded frame construction for stability.

Supply, Installation, Testing, and Commissioning (SITC) oF 1U horizontal cable manager for a 19-

inch rack, made of powder-coated steel with a black finish. The manager shall feature multiple

Rupees Two Hundred

247 1.00 D-rings, typically 5 to 7, to provide organized routing and support for patch cables. The design 282.80 Ea

EightyTwo Paise Eighty Only

should facilitate easy moves, adds, and changes while maintaining proper cable bend radius.

Includes all necessary M6 cage nuts and screws for mounting.

SITC of PIGTAIL LC SM SIMPLEX LENGTH- 1m Rupees Seven Hundred

248 22.00 [Approved by Competent Authority i.e. not Below the rank of Executive Engineer ] 779.72 SeventyNine Paise Ea

SeventyTwo Only

Rupees Four Thousand Four

SITC of Patch Panel Cat 6 UTP Keystone Type- 24 Port-Fully Loaded

249 1.00 4400.57 Hundred Paise FiftySeven Ea

[Approved by Competent Authority i.e. not Below the rank of Executive Engineer ]

Supply, installation, and commissioning of a 24-Port 10/100/1000 Mbps Layer 2 Managed

Gigabit Switch with 2 SFP uplink ports, suitable for standard 19” rack mounting. The switch

Rupees TwentyThree

shall support VLAN, QoS, STP/RSTP/MSTP, SNMP, and have a minimum switching capacity of

250 1.00 23048.19 Thousand FourtyEight Paise Ea

Gbps. It must include all necessary accessories (mounting kit, power cord, etc.), be UL/CE/FCC

Class A certified, and have an internal power supply. Scope includes delivery, rack installation,

configuration, testing, and documentation. Minimum 3-year OEM warranty required.

Rupees One Thousand Nine

SITC of PATCH CORD LC-LC SM DUPLEX LENGTH- 3m

251 2.00 1901.83 Hundred One Paise Ea

[Approved by Competent Authority i.e. not Below the rank of Executive Engineer ]

EightyThree Only

Supply, installation, and configuration of a compact firewall device suitable for securing the

network. The firewall shall provide essential security features including stateful packet

inspection, basic intrusion prevention, URL filtering, and VPN support for secure remote access.

It must efficiently handle the expected network traffic without impacting performance and Rupees EightyFive Thousand

252 1.00 support multiple user profiles and security zones. The scope includes delivery, physical 85244.00 Two Hundred FourtyFour Ea

installation, integration with existing network infrastructure, configuration according to library Only

security policies, testing, and commissioning. Training for basic operation and administration

shall be provided. The device shall come with a minimum one-year warranty and technical

support from the OEM.

Supply, installation, testing, and commissioning of complete Wi-Fi system including wireless

access points (indoor/outdoor as specified), wireless controllers, network switches, structured

cabling, mounting accessories, PoE injectors or PoE switches as required, configuration,

integration with existing LAN infrastructure, and provisioning for seamless wireless connectivity

throughout the designated area. The system shall support the latest Wi-Fi standards (minimum Rupees Sixty Thousand Five

253 2.00 Wi-Fi 6 / 802.11ax), ensure high-speed internet access, robust security protocols (WPA3), 60599.99 Hundred NinetyNine Paise Ea

centralized management, load balancing, roaming capabilities, and scalability for future NinetyNine Only

expansion. All equipment shall be from approved makes, compliant with relevant industry

standards, and installed as per manufacturer’s guidelines and project specifications. The scope

includes necessary civil and electrical works, testing, labeling, documentation, and training to

client personnel, complete in all respects.

Sr. Quantities Item of Work Estimated Unit Total

In Rupees In Words

Supply, delivery, installation, testing, and commissioning of a new 75‑inch LED/Smart TV for

library or display use. The TV should have a minimum native resolution of Full HD (1920×1080),

with built‑in smart functionality (or compatibility with external streaming devices), at least

Rupees One Lakh TwentySix

HDMI ports, USB port(s), and standard audio output connectivity. It should come with a table

254 2.00 126250.00 Thousand Two Hundred Fifty Ea

stand or wall mounting bracket (as required) along with remote, power cable, user manual, and

warranty card (minimum 1 year). The supplier shall mount or place the TV at the designated

location, ensure it works (inputs, network, picture quality), carry out necessary cable routing

(power, HDMI etc.), and hand over in fully operational condition with demonstration to staff.

Supply, delivery, and installation of a brand-new desktop computer system suitable for library

operations and basic administrative tasks. The system shall be equipped with a minimum Intel

Core i5 (12th Generation) or AMD Ryzen 5 processor, 8GB DDR4 RAM (expandable), and a

512GB SSD for fast performance and storage. It shall include a 21.5-inch Full HD LED monitor, a

USB wired keyboard and optical mouse, and be pre-installed with Windows 11 Professional (or

Rupees Fourty Thousand Four

255 22.00 latest version) with proper activation. 40400.00 Ea

The system shall also be pre-installed with a genuine, licensed Microsoft Office suite (latest

version), fully activated and ready for use, including at minimum Word, Excel, and PowerPoint.

The unit shall support both Ethernet LAN and Wi-Fi (minimum Wi-Fi 5), and include essential I/O

ports such as USB 3.0, HDMI, and audio jacks. The system shall come with a 3-year on-site

warranty and technical support.

Supply and installation of a monochrome laser printer for use in the library for tasks such as

printing borrower slips, overdue notices, reports, and other documents. The printer should

have a minimum print speed of 20 pages per minute (ppm), print on dual side of paper, a duty Rupees TwentyTwo Thousand

cycle of at least 10,000 pages per month, and support USB and/or Wi-Fi connectivity. The Two Hundred Twenty Only

printer should come with starter toner, power cables, driver installation CD (or digital access),

and a one-year warranty. Setup and testing at the library site are to be included.

CCTV : Supply, installation, testing, and commissioning of a 5 MP STQC-certified dome‑type IP

CCTV camera with vandal‑proof metal housing, secure firmware, encrypted video transmission,

Rupees Thirteen Thousand Six

257 11.00 and compliance with MeitY Essential Requirements; to be fully integrated, configured, and 13635.00 Ea

Hundred ThirtyFive Only

commissioned as a complete, operable surveillance unit in accordance with the contract

Supply, installation, testing, and commissioning of a 5 MP STQC-certified dome‑type IP CCTV

camera with vandal‑proof metal housing, secure firmware, encrypted video transmission, and

Rupees Fifteen Thousand One

258 7.00 compliance with MeitY Essential Requirements; to be fully integrated, configured, and 15150.00 Ea

Hundred Fifty Only

commissioned as a complete, operable surveillance unit in accordance with the contract

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be

erected on/in wall or ceiling erected with necessary PVC fittings & Junction boxes fixed with Rupees ThirtyThree Paise

adhesive solution & Clamps with following dia of pipes, in approved manner as directed ThirtyThree Only

SITC of CAT6 UTP 23AWG Solid: Per Meter Rupees FourtyThree Paise

[Approved by Competent Authority i.e. not Below the rank of Executive Engineer FourtyThree Only

SITC of Patch Panel Cat 6 UTP Keystone Type- 24 Port-Fully Loaded Rupees Four Thousand Four

261 1.00 [Approved by Competent Authority i.e. not Below the rank of Executive Engineer ] 4400.57 Hundred Paise FiftySeven Ea

Supply, Installation, Testing, and Commissioning (SITC) oF 1U horizontal cable manager for a 19-

inch rack, made of powder-coated steel with a black finish. The manager shall feature multiple

Rupees Two Hundred

262 2.00 D-rings, typically 5 to 7, to provide organized routing and support for patch cables. The design 282.80 Ea

EightyTwo Paise Eighty Only

should facilitate easy moves, adds, and changes while maintaining proper cable bend radius.

Includes all necessary M6 cage nuts and screws for mounting.

SITC of PIGTAIL LC SM SIMPLEX LENGTH- 1m Rupees Seven Hundred

263 18.00 [Approved by Competent Authority i.e. not Below the rank of Executive Engineer ] 779.72 SeventyNine Paise Ea

SeventyTwo Only

SITC of 24 x 10/100/1000BASE-T PoE ports 4 x Gigabit RJ45/SFP Combo ports Advanced L2 Rupees ThirtyOne Thousand

switching and security features L2+ Static Routing Optional “standard mode” or “surveillance

264 1.00 31996.80 Nine Hundred NinetySix Paise Ea

mode” management user interface 193 W PoE budget

[Approved by Competent Authority i.e. not Below the rank of Executive Engineer ] Eighty Only

Rupees One Thousand Nine

SITC of PATCH CORD LC-LC SM DUPLEX LENGTH- 3m

265 1.00 1901.83 Hundred One Paise Ea

[Approved by Competent Authority i.e. not Below the rank of Executive Engineer ]

EightyThree Only

Supply and installation of a 24-channel Network Video Recorder (NVR) with support for up to

SATA hard drives and capable of handling video input resolutions up to 12MP for both live

preview and playback. The NVR shall support H.264/H.265 video compression, provide Rupees SixtyFour Thousand

266 1.00 simultaneous multi-channel recording and playback, and feature user-friendly interface for 64502.64 Five Hundred Two Paise Ea

remote monitoring via web and mobile apps. It must include advanced functionalities such as SixtyFour Only

motion detection, alarm management, and network redundancy options. The unit shall support

PoE ports (if applicable) and be compatible with standard IP cameras.

Supply and installation of 6TB Surveillance-grade Hard Disk Drive (HDD) suitable for

continuous 24x7 operation in CCTV/DVR/NVR systems. The HDD shall be specifically designed

for video surveillance applications with enhanced reliability, high write endurance, and

Rupees Fifteen Thousand

optimized for multiple HD video stream recording. It must support SATA III interface (6 Gbps),

267 2.00 15806.50 Eight Hundred Six Paise Fifty Ea

have a minimum spindle speed of 5400 RPM or higher, and include vibration resistance and

thermal management features. Scope includes delivery, integration with existing recording

system (DVR/NVR), formatting, testing, and ensuring proper recording functionality. HDD must

be from a reputed brand

Sr. Quantities Item of Work Estimated Unit Total

In Rupees In Words

Supply, Installation, Testing, and Commissioning (SITC) of a comprehensive, multi-year e-book

subscription license. This includes the Supply of a robust digital library platform, providing

unlimited access for the specified number of users to a diverse collection of educational and

academic titles, with a significant corpus of content available in both English and Gujarati. The

supplier will also manage the complete Installation and setup of the platform, ensuring full

integration and interoperability across various devices, including desktops, mobile devices (iOS

Rupees Sixteen Thousand Six

268 22.00 and Android), and the NAMO E-Tab application. Post-installation, the bidder must perform 16665.00 Ea

Hundred SixtyFive Only

thorough Testing to verify platform functionality, including seamless user access, reliable

content delivery, compliance with all digital rights management (DRM) policies, and adherence

to the tender's technical specifications. Finally, the successful commissioning involves providing

necessary training to authorized personnel and the official handover of the fully operational

system, backed by a Comprehensive Annual Maintenance Contract (CAMC) covering all

updates, technical support, and operational issues for the duration of the contract.

PA SYSTEM : Supplying and erecting ceiling speaker with rated power of 6 watt/power tapping

30/15/7.5 watt available,opening angle 180 degree H * 77 degree V ,sound pressure level 88 dB Rupees One Thousand Two

,frequency response of 70Hz to 20KHz Hundred Twelve Only

[Approved by Competent Authority i.e. not Below the rank of Executive Engineer ]

Rupees One Lakh

SITC of 16 Zone Standaone Voice Alarm controller 19” 2U rack mount type with Built in Media

FourtyThree Thousand Three

270 1.00 Player with USB (MP3/ WAV/FLAC), Bluetooth V5.0, FM Radio functions, SD CARD , Pre- 143369.49 Ea

Hundred SixtyNine Paise

recorded Evacuation messages and fire alarm integration supported

FourtyNine Only

Supply and installation of a Voice Alarm Call Station designed for emergency communication

and public address in safety and security systems. The call station shall support clear two-way

voice communication, with built-in microphone and speaker, and include features such as call

Rupees FourtyTwo Thousand

initiation, emergency signaling, and integration capability with existing voice alarm or public

271 1.00 42561.40 Five Hundred SixtyOne Paise Ea

address systems. It should be rugged, wall-mountable, and compliant with relevant safety

standards. Scope includes delivery, installation, wiring, integration with the alarm control

system, functional testing, and commissioning. The product must carry a minimum one-year

Supplying , installing & testing approved make Microphone for Speech, Music, & Close to lip

singing with inbuilt protection against breath & wind noise with capability to capture sound

Rupees Two Thousand Six

from long distance & wide area with frequency response 50 - 16000 Hz, having sensitivity 1.8mv

272 1.00 2654.28 Hundred FiftyFour Paise Ea

/ Pa & impedance 430 ohms(Lo -Z) supplied with quick detachable holder, 6 Mtr long. Twin core

TwentyEight Only

cable & 3 pin XLR connector. [[Approved by Competent Authority i.e. not Below the rank of

Executive Engineer ]

Supplying & erecting Amplifier having following specification:

Power Output :100 W (RMS):(130 W Max.)

inputs :5 Mics & 2 Aux.

frequency Response :50-15000 Hz+3db

Rupees Six Thousand Two

Tone Controls :Cut & Boost type

273 2.00 6249.88 Hundred FourtyNine Paise Ea

Speaker Matching :4-8-ohms 70- 100 V line

EightyEight Only

LED Meter :5 LED Array.

The amplifier suitable to operate 240V A.C.& 24 volt D.C. (Battery) with automatic changeover

from AC to Battery operation, duly protected by wrong Battery Polarity connection. [[Approved

by Competent Authority i.e. not Below the rank of Executive Engineer ]

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be

erected on/in wall or ceiling erected with necessary PVC fittings & Junction boxes fixed with Rupees ThirtyThree Paise

adhesive solution & Clamps with following dia of pipes, in approved manner as directed ThirtyThree Only

Supply, Installation, Testing, and Commissioning (SITC) of: High-quality, low-impedance, 2-core,

1.5 sqmm speaker cable for the connection of loudspeakers to the voice alarm Rupees TwentyTwo Paise

amplifier/controller. The cable must be suitable for both normal public address and emergency TwentyTwo Only

voice alarm applications, ensuring clear and reliable audio signal transmission

Total of ELV work (E)

Sr. Quantities Item of Work Estimated Unit Total

In Rupees In Words

FIRE PUMPS, EQUIPMENT, PIPING, VALVES & ACCESSORIES,

Electric Motor Driven Hydrant Pump : Supplying,Installing, testing and commissioning of Fire

authority approved Electrical driven fire pump suitable for automatic/ manual operation

consisting of the following-Rates for erection of pump onlyHorizontal split casing, high pressure,

single/ multistage centrifugal type fire pump having cast iron body, bronze impeller,stainless

steel shaft & capable of delivering 1280 LPM against a total head of 40Mtr while running at

2900 RPM complete with proper connection to suction and delivery line, and including bypass

arrangement for testing of pumps as per the requirement. Suitable mechanical seal with

mounting aggangement shall be included, having a name plate indicating suction, delivery,

head, discharge, stages, RPM and direction of rotation. Y Stainers at pump input shall be

provided as per manufacturer requirements. Pump shall be capable of furnishing not less than

150% of rated capacity at a head not less than 65 % of rated head. The shut off head shall not

Rupees One Lakh ThirtySix

exceed 120% of rated head. Squirrel cage, induction motor, TEFC type suitable for 415 + 10%V,

276 1.00 136350 Thousand Three Hundred Set

3 phase, 50 Hz, AC supply, of suitable HP rating for the above pump with synchronous speed of

2900 RPM conforming to IP 55 protection & class 'F' insulation. The motor shall conform to IS

325 1978 (up to date) with flexible coupling and coupling guard .Factory Fabricated Common

base plate for mounting pump and motor fabricated of mild steel channel as per

manufacturer's recommendation with heavy duty Anti Vibration pads (4 Nos., heavy duty).

Grouting bolts to be provided and installed by vendor at his cost Flexible Coupling and coupling

guard for direct coupling of pump and motor.Drain Pipe with Valve Main Fire Pump Discharge

: 1280 LPM Pumping Head : 40 M Pump Size : 30 HP Rate should included

interconnection cables and Cable box if reqd for cable conn. to motor.

Electrical Motor Driven Jockey Pump For Hydrant & Sprinkler System

Supplying,Installing, testing & commissioning of fire authority approved electrically driven

Jockey pump suitable for automatic/manual operation consisting of the following: Horizontal /

Vertical mounted multistage jockey pump having cast iron body, S.S. impeller, stainless shaft

with mechanical seal capable of delivering 1280 LPM against total head of 40Mtr while running

at 2900 RPM complete. The system shall be complete with necessary pressure gauge with gun

metal shut off cock on delivery side including bypass arrangement for testing of working of the

pumping set as required. The pump should meet the requirement of IS 15105:2002 and must be

approved by the local fire authority. Y-Stainers at pump input shall be provided as per

manufacturer requirements.Squirrel cage induction motor suitable for 415 + 10%V, 3 phase,

Hz, AC supply of suitable HP rating for the above pump with synchronous speed of 2900 RPM

T.E.F.C type connected to pump with flexible coupling and coupling guard .Factory fabricated Rupees SeventyTwo

277 1.00 Common base plate for mounting pump and motor fabricated of mild steel channel as per 72720 Thousand Seven Hundred Set

manufacturer's recommendation with heavy duty 4 Nos. Anti Vibration pads.(Cushy foot) . Twenty Only

grouting bolts to be provided and installed by the vendor at his cost Suitable reinforced cement

concrete pump foundations as per manufacturer's design including foundation bolts, washers

Drain pipe with valve (25 mm dia)

Discharge : 1280 LPM

Pumping Head : 40 M

Pump Size : 10 HP

Rate shall include inter connecting cables and cable box if reqd for cable conn to motor

Diesel Fire Pump

Supplying, Installation, Testing and commissioning of Diesel engine driven fire pump suitable for

automatic operation and consisting of following: Horizontal type, centrifugal End Suction pump

of cast iron body & bronze impeller , mechanical seal to ensure a minimum pressure of 3.5 kg /

sq.cm. at highest and farthest outlet at specified flow of 137 m3/Hour@ 40M. head conforming

Rupees Three Lakh

to IS 1520. with M.S.fabricated common base plate, coupling, coupling guard, foundation bolts

278 1.00 348450.00 FourtyEight Thousand Four Set

etc. as required

Hundred Fifty Only

Diesel Fire Pump

Discharge : 1280 LPM

Pumping Head : 40 M

Pump Size : 30 HP

Fire pump panel (Combined for All Pumps) and electrical works - Starter panel with star delta

or as per CFO approved starters rated to suite pump HP with necessary protection feautres like

SPP / ELR / OL / SC / phase and on off indicating lamps. The busbars shall be of Al - 0.8 A / sq

mm size. Panel shall be fabricated from 14G sheet steel with seven tank process powder coated

and shall be min IP 52. Panel shall have Ammeter / Voltmeter and KWh meter. Cabling /

earthing from panel to pump shall be scope of vendor without any extra cost. Cabling - supply /

laying and terminating, shall be Al XLPE armoured / Cu XLPE armoured / as per manufacturers

specifications with necessary terminal box to terminate the cables. Panel shall be rated min for Rupees Two Lakh TwentyTwo

25KA fault level. Cable trays - hot dip GI ladder type 16 gauge with required supports shall be Thousand Two Hundred Only

used for cabling. Panel shall have one incomer MCCB / ACB of required rating where by

incoming supply and earthing shall be terminated by electrical contractor.Starters shall be

suitable for respective motors.panel to take inputs from pressure switch/on-off switch . Flow

switch wiring shall be in suitable mms pvc consuits. Panel should be manufactured by CPRI

approved panel builder

Supply, Installation, testing and commissioning of CAST IRON Y-TYPE STRAINER (flanged) PN-1.6 Rupees Fifteen Thousand

280 1.00 ; body - C.I., Screen stainless steel 150 mm dia 15326.75 Three Hundred TwentySix Each

Paise SeventyFive Only

Sr. Quantities Item of Work Estimated Unit Total

In Rupees In Words

Supplying,Installing, testing & commissioning of dial type Pressure Guage having 100 mm dial & Rupees Two Thousand One

281 3.00 range of 0-15 Kg/cm2 with syphon and cock. 2151.30 Hundred FiftyOne Paise Thirty Each

Supplying,Installing, testing & commissioning of Pressure Switch required accessories Rupees Two Thousand

Supply, installation, testing and commissioning of butterfly valve PN 1.6, with s.s seat duly lSI

Rupees Four Thousand Eight

283 1.00 marked complete with Nuts, Bolts, washers, gaskets, confirming to IS 13095, of following sizes 4848.00 Each

Hundred FourtyEight Only

as required. 150 mm dia

Supply, installation, testing and commissioning of butterfly valve PN 1.6, with s.s seat duly lSI

Rupees Three Thousand Eight

284 2.00 marked complete with Nuts, Bolts, washers, gaskets, confirming to IS 13095, of following sizes 3838.00 Each

Hundred ThirtyEight Only

as required. 80 mm dia

Supply, installation, testing and commissioning of butterfly valve PN 1.6, with s.s seat duly lSI

Rupees Three Thousand Eight

285 1.00 marked complete with Nuts, Bolts, washers, gaskets, confirming to IS 13095, of following sizes 3838.00 Each

Hundred ThirtyEight Only

as required. 50 mm dia

Supplying,Installing, testing & commissioning of CI dual plate non-return valve of following sizes

Rupees Five Thousand Two

286 1.00 conforming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc. as required. 5252.00 Each

Hundred FiftyTwo Only

Supply, Installation, Testing and Commissioning of the following sizes of flange jointed /

screwed / welded, M.S. Pipes of Class C (Medium class) ISI marked including accessories such

as MS bracket, U clamps with Anchor fasteners, tees / elbows / reducers / couplings / unions / Rupees One Thousand Four

287 115.00 bends / flanges etc., and laying on the surface including painting with two coats of anticorrosive 1424.10 Hundred TwentyFour Paise Mtr.

primer and two coats of approved red enamel paint after laying and testing after Installation Ten Only

etc. as per specifications complete as required. 150 mm

Supply, Installation, Testing and Commissioning of the following sizes of flange jointed /

screwed / welded, M.S. Pipes of Class C (Medium class) ISI marked including accessories such

as MS bracket, U clamps with Anchor fasteners, tees / elbows / reducers / couplings / unions / Rupees One Thousand Two

288 14.00 bends / flanges etc., and laying on the surface including painting with two coats of anticorrosive 1232.20 Hundred ThirtyTwo Paise Mtr.

primer and two coats of approved red enamel paint after laying and testing after Installation Twenty Only

etc. as per specifications complete as required. 100 mm

Supply, Installation, Testing and Commissioning of the following sizes of flange jointed /

screwed / welded, M.S. Pipes of Class C (Medium class) ISI marked including accessories such

as MS bracket, U clamps with Anchor fasteners, tees / elbows / reducers / couplings / unions /

Rupees Nine Hundred

289 20.00 bends / flanges etc., and laying on the surface including painting with two coats of anticorrosive 949.40 Mtr.

FourtyNine Paise Fourty Only

primer and two coats of approved red enamel paint after laying and testing after Installation

etc. as per specifications complete as required. 80 mm

Supply, Installation, Testing and Commissioning of the following sizes of flange jointed /

screwed / welded, M.S. Pipes of Class C (Medium class) ISI marked including accessories such

as MS bracket, U clamps with Anchor fasteners, tees / elbows / reducers / couplings / unions /

Rupees Seven Hundred

290 20.00 bends / flanges etc., and laying on the surface including painting with two coats of anticorrosive 717.10 Mtr.

Seventeen Paise Ten Only

primer and two coats of approved red enamel paint after laying and testing after Installation

etc. as per specifications complete as required. 65 mm

Supply, Installation, Testing and Commissioning of the following sizes of flange jointed /

screwed / welded, M.S. Pipes of Class C (Medium class) ISI marked including accessories such

as MS bracket, U clamps with Anchor fasteners, tees / elbows / reducers / couplings / unions /

Rupees Five Hundred

291 36.00 bends / flanges etc., and laying on the surface including painting with two coats of anticorrosive 585.80 Mtr.

EightyFive Paise Eighty Only

primer and two coats of approved red enamel paint after laying and testing after Installation

etc. as per specifications complete as required. 50 mm

Supply, Installation, Testing and Commissioning of the following sizes of flange jointed /

screwed / welded, M.S. Pipes of Class C (Medium class) ISI marked including accessories such

as MS bracket, U clamps with Anchor fasteners, tees / elbows / reducers / couplings / unions /

Rupees Four Hundred

292 20.00 bends / flanges etc., and laying on the surface including painting with two coats of anticorrosive 494.90 Mtr.

NinetyFour Paise Ninety Only

primer and two coats of approved red enamel paint after laying and testing after Installation

etc. as per specifications complete as required. 40 mm

Supply, Installation, Testing and Commissioning of the following sizes of flange jointed /

screwed / welded, M.S. Pipes of Class C (Medium class) ISI marked including accessories such

as MS bracket, U clamps with Anchor fasteners, tees / elbows / reducers / couplings / unions / Rupees Four Hundred

293 20.00 bends / flanges etc., and laying on the surface including painting with two coats of anticorrosive 449.45 FourtyNine Paise FourtyFive Mtr.

primer and two coats of approved red enamel paint after laying and testing after Installation Only

etc. as per specifications complete as required. 32 mm

Supply, Installation, Testing and Commissioning of the following sizes of flange jointed /

screwed / welded, M.S. Pipes of Class C (Medium class) ISI marked including accessories such

as MS bracket, U clamps with Anchor fasteners, tees / elbows / reducers / couplings / unions /

Rupees Two Hundred

294 154.00 bends / flanges etc., and laying on the surface including painting with two coats of anticorrosive 252.50 Mtr.

FiftyTwo Paise Fifty Only

primer and two coats of approved red enamel paint after laying and testing after Installation

etc. as per specifications complete as required. 25 mm

Supplying,Installing, testing & commissioning of Weather proof standard fire hose cabinet (750

mm x 600 mm x 300 mm deep) made out of 16 SWG powder coated M.S. sheet having single or

double opening glazed (4.0 mm thick glass) shutter including necessary locking arrangement by

Rupees Five Thousand One

295 1.00 allen key, stove enamelled Fire red finish (as per IS : 5, shade no. 536) with " Fire Hose" marked 5151.00 Each

Hundred FiftyOne Only

on front, suitable for housing 2 nos. 15m long 63 mm dia Hose pipe, 1 No. branch pipe & nozzle

spanner (For External Hydrant).

Sr. Quantities Item of Work Estimated Unit Total

In Rupees In Words

Supply, Installation, Testing and Commissioning of Weather proof Standard Fire Hose Cabinet

wall mounting type (450 mm x 600 mm x 250 mm deep) having single or double opening with Rupees One Thousand Eight

necessary locking arrangement by allan key suitable for housing 1 nos. hose pipe, 1 no. Branch Hundred Eighteen Only

pipe & nozzle spanner.

Supply ,installation, testing and commissioning S.S. Single Headed Fire Hydrant Valve with

80mm N.B. flanged inlet, 63 mm dia female instantaneous outlet type. S.S. coupling, blankcap,

Rupees Three Thousand

297 3.00 chain, twist release type lug & all accessories Conforming to IS:5290. Including fixing with 3030.00 Each

supports, flanged tapping from wet riser,orifice plate complete as required by the Local Fire

Supply, installation, testing and commissioning non-percolating rubber reinforced lined fire

Rupees Three Thousand Two

298 3.00 Hose pipe (as per IS:903) of 63 mm dia and 15 mtrs long. 3232.00 Each

Hundred ThirtyTwo Only

Supply, Installation, Testing and commissioning of 63 mm dia instantaneous pattern aluminium Rupees Eight Hundred Eight

short branch pipe Only

Supply, installation, testing and commissioning of First Aid Hose Reel equipment conforming to

IS:884 comprising of hose reel drum, 8 mm shut off nozzle, Rubber hose reel tubing as per IS:

Rupees Four Thousand One

300 3.00 444 of 25 mm dia x 45 mtr. long, painting, Manual fix type with fixing bracket, anchor fastener, 4141.00 Each

Hundred FourtyOne Only

bolts & nuts etc. complete as required by Local Fire Authority.

Supply, installation, testing and commissioning of SS Ball Valve. Rupees Eight Hundred Eight

(a) 25mm dia Only

Supply, installation, testing and commissioning of Cast lron Four Way Fire Brigade Inlet as per

Rupees Four Thousand Eight

302 1.00 IS:904 having 63 mm dia inlet with blank cap and chain with necessary fittings, flanges, nut bolts 4848.00 Each

Hundred FourtyEight Only

etc. complete as required.

Supply, Installation, Testing and Commissioning of Gun Metal Air Release Valve with necessary

Rupees Three Thousand Five

303 1.00 fittings. Size: 25 mm (For Riser) 3535.00 Each

Hundred ThirtyFive Only

Supply, Installation, Testing and commissioning of Quartzoid Bulb type Sprinkler Heads. (a)

Rupees Three Hundred

304 62.00 Pendent Sprinkler 57°C - standard response 353.50 Each

FiftyThree Paise Fifty Only

Supply, installation, testing and commissioning of ABC type Fire Extinguisher of 6.0 kg confirm

Rupees One Thousand Four

to IS:15683, with ISI marked / TAC approved fitted with required accessories including wall

305 2.00 1424.10 Hundred TwentyFour Paise Each

suspension brackets.

Supply, installation, testing and commissioning of Carbon Dioxide (Co2) type Fire Extinguisher

Rupees Three Thousand Eight

306 2.00 of 4.5 kg confirm to IS:15683, with ISI marked / TAC approved fitted with required accessories 3838.00 Each

Hundred ThirtyEight Only

including wall suspension brackets.

Supplying,Installing, testing & commissioning of fire alarm and pump trigger system as per

307 2.00 requirement and specification consisting of following items Manual call point: 606.00 Rupees Six Hundred Six Only Each

Supplying,Installing, testing & commissioning of fire alarm and pump trigger system as per

Rupees Seven Hundred

308 2.00 requirement and specification consisting of following items Hooters: 757.50 Each

FiftySeven Paise Fifty Only

Supplying,Installing, testing & commissioning of fire alarm and pump trigger system as per

Rupees Five Hundred Five

309 2.00 requirement and specification consisting of following items Pump On / Off switch: 505.00 Each

Supplying,Installing, testing & commissioning of fire alarm and pump trigger system as per

requirement and specification consisting of following items (a) 4 core 1.5 sq.mm cu. Flexinble Rupees Thirty Paise Thirty

wire with pvc pipe & hardware for pump on/off switch Only

Supplying,Installing, testing & commissioning of fire alarm and pump trigger system as per

Rupees Fourty Paise Fourty

311 40.00 requirement and specification consisting of following items (b)2 core 1.5 sq.mm cu. Flexible 40.40 Mtr.

wire with pvc pipe & hardware for pump on/off switch

Providing and fixing M.S. structural work fabricated from standard sections, (MS rounds, angles,

channels etc.) including cutting to size, drilling, welding, including cost of fasteners, clamps in

Rupees One Hundred Six

312 30.00 RCC structural members as directed, including two or more coats of synthetic paint over one 106.05 kg

Paise Five Only

coat of primer after surface preparation including cutting and making good walls (Structural

other than pipe supoort).

Painting of above ground lines with two coats of red oxide primer and two coat of sinthetic Rupees Seven Hundred Seven

enamal paint (PO.Red) Only

Supplying of AUTOGLOW Signages in Block / Small Letters of Specified Sizes: Fire lift size: 4" X Rupees Two Hundred

12" FiftyTwo Paise Fifty Only

Supplying of AUTOGLOW Signages in Block / Small Letters of Specified Sizes: Fire Hydrant: 4" X Rupees Two Hundred

12" FiftyTwo Paise Fifty Only

Supplying of AUTOGLOW Signages in Block / Small Letters of Specified Sizes: "DCP" Rupees One Hundred

Extinguisher: 8" X 4" FiftyOne Paise Fifty Only

Supplying of AUTOGLOW Signages in Block / Small Letters of Specified Sizes: "CO2" Rupees One Hundred

Extinguisher: 8" x 4" FiftyOne Paise Fifty Only

Supplying of AUTOGLOW Signages in Block / Small Letters of Specified Sizes : In case of Fire, do

Rupees Three Hundred

318 2.00 not use lift, use staircase:8"x8" 353.50 Each

FiftyThree Paise Fifty Only

Total of Fire Fighting work (F)

Water Supply : Providing and fixing, in proper line and level (with necessary support like, brick

masonry pedestals and battens, if necessary) to floor, approved quality, heavy duty, White

UPVC-Schedule 40 Grade as per ASTM D-1785, of Astral or equivalent, Open & Conceal piping,

complete, including jointing with rubbering and airtight joints, with necessary specials, couplers, Rupees SeventyTwo Paise

elbow, equal tees, tail piece, adapter (both male and female), reducer (single stage, double SixtyFive Only

stage and triple stage), end cap, fabricated bend, etc., and lubricant or jointing material,

including testing, cutting, making good the wall, ceiling and floor etc. Testing & installation of

pipe lines as per drawing & specification. 15 mm

Sr. Quantities Item of Work Estimated Unit Total

In Rupees In Words

Providing and fixing, in proper line and level (with necessary support like, brick masonry

pedestals and battens, if necessary) to floor, approved quality, heavy duty, White UPVC-

Schedule 40 Grade as per ASTM D-1785, of Astral or equivalent, Open & Conceal piping,

Rupees One Hundred

complete, including jointing with rubbering and airtight joints, with necessary specials, couplers,

320 187.00 198.97 NinetyEight Paise Rmt

elbow, equal tees, tail piece, adapter (both male and female), reducer (single stage, double

NinetySeven Only

stage and triple stage), end cap, fabricated bend, etc., and lubricant or jointing material,

including testing, cutting, making good the wall, ceiling and floor etc. Testing & installation of

pipe lines as per drawing & specification. 20 mm

Providing and fixing, in proper line and level (with necessary support like, brick masonry

pedestals and battens, if necessary) to floor, approved quality, heavy duty, White UPVC-

Schedule 40 Grade as per ASTM D-1785, of Astral or equivalent, Open & Conceal piping,

complete, including jointing with rubbering and airtight joints, with necessary specials, couplers, Rupees NinetyOne Paise

elbow, equal tees, tail piece, adapter (both male and female), reducer (single stage, double EightyFour Only

stage and triple stage), end cap, fabricated bend, etc., and lubricant or jointing material,

including testing, cutting, making good the wall, ceiling and floor etc. Testing & installation of

pipe lines as per drawing & specification. 25 mm

Providing and fixing, in proper line and level (with necessary support like, brick masonry

pedestals and battens, if necessary) to floor, approved quality, heavy duty, White UPVC-

Schedule 40 Grade as per ASTM D-1785, of Astral or equivalent, Open & Conceal piping,

complete, including jointing with rubbering and airtight joints, with necessary specials, couplers, Rupees One Hundred

elbow, equal tees, tail piece, adapter (both male and female), reducer (single stage, double Nineteen Paise Fifteen Only

stage and triple stage), end cap, fabricated bend, etc., and lubricant or jointing material,

including testing, cutting, making good the wall, ceiling and floor etc. Testing & installation of

pipe lines as per drawing & specification. 32 mm

Providing and fixing, in proper line and level (with necessary support like, brick masonry

pedestals and battens, if necessary) to floor, approved quality, heavy duty, White UPVC-

Schedule 40 Grade as per ASTM D-1785, of Astral or equivalent, Open & Conceal piping,

complete, including jointing with rubbering and airtight joints, with necessary specials, couplers, Rupees One Hundred

elbow, equal tees, tail piece, adapter (both male and female), reducer (single stage, double FourtyEight Paise Twelve Only

stage and triple stage), end cap, fabricated bend, etc., and lubricant or jointing material,

including testing, cutting, making good the wall, ceiling and floor etc. Testing & installation of

pipe lines as per drawing & specification. 40 mm

Providing and fixing, in proper line and level (with necessary support like, brick masonry

pedestals and battens, if necessary) to floor, approved quality, heavy duty, White UPVC-

Schedule 40 Grade as per ASTM D-1785, of Astral or equivalent, Open & Conceal piping,

Rupees One Hundred

complete, including jointing with rubbering and airtight joints, with necessary specials, couplers,

324 3.00 195.67 NinetyFive Paise SixtySeven Rmt

elbow, equal tees, tail piece, adapter (both male and female), reducer (single stage, double

stage and triple stage), end cap, fabricated bend, etc., and lubricant or jointing material,

including testing, cutting, making good the wall, ceiling and floor etc. Testing & installation of

pipe lines as per drawing & specification. 50 mm

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having

National Sanitation Foundation (NSF) seal for potable water of Rupees Two Hundred Eight

following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and Paise Eighty Only

floor etc. complete. All Conceal Pipe line Cold & Hot Water & RO Water 20 mm

Providing, fixing, jointing and testing, heavy quality cast bronze / brass BALL VALVE / OR

WHEEL valves of approved make, including flanges / unions, nuts, bolts, washers, etc. Rupees Nine Hundred Nine

complete, as approved by the Architect and Engineer-in-charge for water supply lines of the Only

following Nominal bore (NB) size: 15 mm

Providing, fixing, jointing and testing, heavy quality cast bronze / brass BALL VALVE / OR

WHEEL valves of approved make, including flanges / unions, nuts, bolts, washers, etc. Rupees One Thousand Two

complete, as approved by the Architect and Engineer-in-charge for water supply lines of the Hundred Twelve Only

following Nominal bore (NB) size: 20 mm

Providing, fixing, jointing and testing, heavy quality cast bronze / brass BALL VALVE / OR

WHEEL valves of approved make, including flanges / unions, nuts, bolts, washers, etc. Rupees One Thousand Eight

complete, as approved by the Architect and Engineer-in-charge for water supply lines of the Hundred Eighteen Only

following Nominal bore (NB) size: 25 mm

Providing, fixing, jointing and testing, heavy quality cast bronze / brass BALL VALVE / OR

Rupees Two Thousand Seven

WHEEL valves of approved make, including flanges / unions, nuts, bolts, washers, etc.

329 7.00 2777.5 Hundred SeventySeven Paise Nos.

complete, as approved by the Architect and Engineer-in-charge for water supply lines of the

following Nominal bore (NB) size: 32 mm

Providing, fixing, jointing and testing, heavy quality cast bronze / brass BALL VALVE / OR

Rupees Three Thousand Five

WHEEL valves of approved make, including flanges / unions, nuts, bolts, washers, etc.

330 6.00 3595.6 Hundred NinetyFive Paise Nos.

complete, as approved by the Architect and Engineer-in-charge for water supply lines of the

following Nominal bore (NB) size: 40 mm

Providing, fixing, jointing and testing, heavy quality cast bronze / brass BALL VALVE / OR

Rupees Four Thousand Eight

WHEEL valves of approved make, including flanges / unions, nuts, bolts, washers, etc.

331 3.00 4898.50 Hundred NinetyEight Paise Nos.

complete, as approved by the Architect and Engineer-in-charge for water supply lines of the

following Nominal bore (NB) size: 50 mm

Providing, fixing, jointing and testing, heavy Quality Gun metal or brass Non return valve

Rupees Two Thousand Five

332 3.00 confirming to IS 778, with screwed / flanged ends, 20 Kg/m2 of approved make, on water 2525.00 Nos.

Hundred TwentyFive Only

supply lines of the following Nominal bore (NB) size: 40 mm

Sr. Quantities Item of Work Estimated Unit Total

In Rupees In Words

INTERNAL DRAINAGE : Providing and fixing Approved SWR Type B quality, heavy duty, UPVC

pipes - Ring Fit & Self Fit, Supreme or equivalent make, Confirming to IS 13592 & Fitting

confirming to IS 14735 for waste water or soil waste pipe, with necessary specials, bends, such

as `Y' junction, `T' junction (both single and double), including plugs, shoes, cowls, flange

compression type fittings, wall clips, in proper line and level with necessary support like Rupees Eight Hundred

333 88.00 brackets/clamps, clips, RCC or brick pedestals or battens, if necessary, to wall, ceiling and floor, 834.38 ThirtyFour Paise ThirtyEight Rmt

open or concealed complete jointing with rubberising and airtight joints, with ‘T’ shaped rubber Only

ring, etc., and lubricant or jointing material, including testing, cutting, making good the wall,

ceiling and floor, etc. Testing & installation of pipe lines as per drawing & specification. 160 mm.

(Soil + Waste + Rain Water) - Type B

Providing and fixing Approved SWR Type B quality, heavy duty, UPVC pipes - Ring Fit & Self Fit,

Supreme or equivalent make, Confirming to IS 13592 & Fitting confirming to IS 14735 for waste

water or soil waste pipe, with necessary specials, bends, such as `Y' junction, `T' junction (both

single and double), including plugs, shoes, cowls, flange compression type fittings, wall clips, in

proper line and level with necessary support like brackets/clamps, clips, RCC or brick pedestals

Rupees Eight Hundred

334 55.00 or battens, if necessary, to wall, ceiling and floor, open or concealed complete jointing with 876.90 Rmt

SeventySix Paise Ninety Only

rubberising and airtight joints, with ‘T’ shaped rubber ring, etc., and lubricant or jointing

material, including testing, cutting, making good the wall, ceiling and floor, etc. Testing &

installation of pipe lines as per drawing & specification. 110 mm. (Soil + Waste + Rain Water) -

Providing and fixing Approved SWR Type B quality, heavy duty, UPVC pipes - Ring Fit & Self Fit,

Supreme or equivalent make, Confirming to IS 13592 & Fitting confirming to IS 14735 for waste

water or soil waste pipe, with necessary specials, bends, such as `Y' junction, `T' junction (both

single and double), including plugs, shoes, cowls, flange compression type fittings, wall clips, in

proper line and level with necessary support like brackets/clamps, clips, RCC or brick pedestals

Rupees Two Hundred Eighty

335 77.00 or battens, if necessary, to wall, ceiling and floor, open or concealed complete jointing with 280.23 Rmt

Paise TwentyThree Only

rubberising and airtight joints, with ‘T’ shaped rubber ring, etc., and lubricant or jointing

material, including testing, cutting, making good the wall, ceiling and floor, etc. Testing &

installation of pipe lines as per drawing & specification. 75 mm. - Balcony + Standing Balcony +

AC Drain - PVC 10 KG

Providing and fixing Approved SWR Type B quality, heavy duty, UPVC pipes - Ring Fit & Self Fit,

Supreme or equivalent make, Confirming to IS 13592 & Fitting confirming to IS 14735 for waste

water or soil waste pipe, with necessary specials, bends, such as `Y' junction, `T' junction (both

single and double), including plugs, shoes, cowls, flange compression type fittings, wall clips, in

proper line and level with necessary support like brackets/clamps, clips, RCC or brick pedestals

Rupees One Hundred

336 143.00 or battens, if necessary, to wall, ceiling and floor, open or concealed complete jointing with 149.30 Rmt

FourtyNine Paise Thirty Only

rubberising and airtight joints, with ‘T’ shaped rubber ring, etc., and lubricant or jointing

material, including testing, cutting, making good the wall, ceiling and floor, etc. Testing &

installation of pipe lines as per drawing & specification. 40 mm for waste water for Sink - PVC

Providing and fixing Approved SWR Type B quality, heavy duty, UPVC pipes - Ring Fit & Self Fit,

Supreme or equivalent make, Confirming to IS 13592 & Fitting confirming to IS 14735 for waste

water or soil waste pipe, with necessary specials, bends, such as `Y' junction, `T' junction (both

single and double), including plugs, shoes, cowls, flange compression type fittings, wall clips, in

proper line and level with necessary support like brackets/clamps, clips, RCC or brick pedestals Rupees One Hundred

337 44.00 or battens, if necessary, to wall, ceiling and floor, open or concealed complete jointing with 126.47 TwentySix Paise FourtySeven Rmt

rubberising and airtight joints, with ‘T’ shaped rubber ring, etc., and lubricant or jointing Only

material, including testing, cutting, making good the wall, ceiling and floor, etc. Testing &

installation of pipe lines as per drawing & specification. 32 mm for waste water for Wash

basin - PVC 10 KG

Providing, fixing, jointing and testing IS 14735 for Drain PVC SWR 'P' - traps of self cleansing

design with water seal not less than 50 mm., with or without vent, cutting chases / hole in

floors / slabs and bringing the same in proper condition and shape after placing the trap in right

338 29.00 position in case of suspended / open plumbing or setting the trap in 1:2:4 CC in case of 606.00 Rupees Six Hundred Six Only Nos.

concealed plumbing , etc. complete, as required. The trap shall be 'P' type, of following sizes:

110 x 110 mm OD inlet / outlet

Providing and fixing Heavy class S.S. grating with Mosquito proof S.S. strainer of Chilly or

Rupees Four Hundred

339 29.00 equivalent make, as approved, (cockroach trap) including setting in floor with cement mortor 419.15 Nos.

Nineteen Paise Fifteen Only

to match with floor finish as per architect requirements.

Providing and fixing, PVC cowl, on C.I / PVC ventilating pipes and verticals for soil, waste and

Rupees Five Hundred Five

340 9.00 rain water Pipes at top level / terrace level, as specified and required, etc. complete. 110 OD 505.17 Nos.

Paise Seventeen Only

Providing and fixing, PVC cowl, on C.I / PVC ventilating pipes and verticals for soil, waste and

Rupees Three Hundred

341 4.00 rain water Pipes at top level / terrace level, as specified and required, etc. complete. 110 OD 393.04 Nos.

NinetyThree Paise Four Only

Providing and fixing PVC SWR Nahni trap IS 14735 for drain - 100 mm diameter with jali of the

Rupees Five Hundred

following nominal diameter of self cleansing design with C.I scread down or hinged grating

342 4.00 586.27 EightySix Paise TwentySeven Nos.

including the cost of cutting and making good the walls. (for Balcony)

EXTERNAL DRAINAGE : Providing laying (to level or slopes) and jointing reinforced concrete

Rupees Three Hundred

Light duty non-pressure pipes I.S., class NP2 of the following internal diameter with collars and

343 66.00 359.84 FiftyNine Paise EightyFour Rmt

butt ends prepared for collar joints including testing, of joints complete.(a) 250mm

Providing laying (to level or slopes) and jointing reinforced concrete Light duty non-pressure

Rupees Two Hundred

pipes I.S., class NP2 of the following internal diameter with collars and butt ends prepared for

344 33.00 257.19 FiftySeven Paise Nineteen Rmt

collar joints including testing, of joints complete.(B) 150mm

Sr. Quantities Item of Work Estimated Unit Total

In Rupees In Words

Providing, fixing, jointing and testing salt glazed stoneware Gully trap, class `A', including

excavation in all soil types, bailing or pumping out water from trenches, shoring whenever

necessary testing,refilling, in layers ramming & consolidation, removing away the surplus earth

& spoils, dumping it on site or carting away to lead of 100 meters as directed, incl. embedding

the trap in CC 1:2:4, construction of brick masonry chamber, internal clear size 300 mm. x

mm., in brick work 230 mm. thick, in CM 1:4, plastering inside, outside and all exposed surfaces

Rupees Three Thousand Eight

with CM 1:3, 12 mm. thick, with 300 x 300mm Gully trap chamber & providing, fixing CI frame

345 11.00 3806.53 Hundred Six Paise FiftyThree Nos.

and cover 300 x 300 mm., weighing together not less than 12.5 Kg., painting of all CI items with

3 coats of approved bitumastic paint, etc. Complete.of the following diameter size: salt glazed

stoneware gully trap, class `A', of 150 mm. dia. inlet and 150 mm. outlet, Cast iron cover 300 x

300 Constructing Brick masonry road gully chamber 500mm x 450mm x 600mm including

500mm x 450mm C.I. horizontal grating with frame complete.

Constructing Inspection chamber 450 x450 x 600 mm clear size in 230 mm thick brick masonry

with cement mortar (1:5) as per ISI with 150 mm thick 1:3:6 P.C.C. bedding, necessary benching

in concrete (M-15) and 20 mm thick smooth cement plaster (1:4) from inside, C.I. steps as

Rupees Two Thousand Five

necessary and rough cement plaster 20 mm thick in c.m. 1:4 outside, with 50 kg. Full size C.I.

346 9.00 2545.86 Hundred FourtyFive Paise Nos.

manhole cover and frame (Approved Make) including all excavation in all soil types, refilling

sides in layers with selected earth ramming and consolidating, removing away surplus soil or

dumping it on site as directed (Depth upto 1500 mm to invert).

Constructing brick masonry chamber for underground C.I. Inspection chamber and bends with

bricks having crushing strength not less than 35Kg/ Cm2 in C.M. 1:5

C.I. cover with frame (Light duty) 455mm x 610mm intenal dimensions total weight of cover

with frame to be not less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of Rupees Seven Thousand One

347 9.00 frame 15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1-cement :2- coarse sand :4-graded stone 7180.44 Hundred Eighty Paise Nos.

aggregate 20mm size) foundation concrete 1:5:10 inside plaster 15mm thick with cement FourtyFour Only

mortar 1:3 finished smooth with a floating coat of neat cement on walls and bed concrete etc.

complete.(iii) Inside dimensions 600mm x 850 mm and 450mm deep for pipe lines with three or

Extra over and above item no. beyond 1.5 m. depth, for every additional depth of 0.1 m. or Rupees Three Hundred

348 9.00 part thereof, for brick masonry Inspection chamber. 325.59 TwentyFive Paise FiftyNine Nos.

Providing and fixing CI Cover manhole frame and cover 455 x 610, light / medium / heavy

weight,Circular / rectangular tested as per IS:1726 for load bearing.The cover is to be provided

Rupees Nine Hundred

with a 5mm thick high abrasion surface.The cover is to be of double seal type with SS

349 9.00 965.49 SixtyFive Paise FourtyNine Nos.

Socket type key hole lifting / Rod lifting arrangement . The lifting arrangement is to be closed

from the bottom side. etc. complete as directed by E-I-C.

UTILITY ITEMS : S.I.T.C. submersible pump set for bore of 200 mm. dia. or more having 3 phase

Rupees One Lakh Seventeen

motor capacity about 50-55 H.P discharge capacity having . Lifting and Lowering taken extra.

350 1.00 117502.39 Thousand Five Hundred Two Nos.

(A) ( 13 Stage) 100 to 400 L.P.M. discharge at the head 182 to 265 mtrs. suitable for 80 mm dia.

Paise ThirtyNine Only

Delivery pipe Cat.III

Installing, testing and commissioing of Pump system comprising of horizontal Submersible

Pumps with SS casing, SS impeller, SS Shaft and driven by 415 V AC, 3 phase, 50HZ., motor

running at 2900 rpm speed and shall be supplied with all accessories viz., base plate, coupling,

Rupees ThirtyFive Thousand

351 1.00 motor, VFD based control panel, dry run & overload protection, cabling up to panel, earthing, GI 35350.00 SET

Three Hundred Fifty Only

medium duty suction, delivery & header pipes, pressure gauge, pressure switches, pressure

transmitter, suction ball valves & delivery ball valves & check valves etc., complete. 100 lpm.,

40mtr., (To GROUND FLOOR TO TERRACE TANK) FOR DOMESTIC WATER

Supply, installation, testing & commissioning of Water level controller for the OH tanks with

Rupees Ten Thousand One

352 2.00 switches, hardwares, interlocking with panel, etc. For Under Ground tank & OH Tank 10100.00 SET

Rupees One Lakh FourtyFive

Constructing masonry Soak well with mesonery work bottom side 6'' PCC work, with minimum

353 1.00 145187.50 Thousand One Hundred SET

9'' thik brick wall with 30% opening in wall area, with Top side 6'' RCC Slab, 400x400 Inspection

EightySeven Paise Fifty Only

chamber, top side with FRP cover fitting, 110mm Air vent line. Dia 3.0 Meter x 6 meter Depth

Providing erecting and fixing double coated ISI water tank of required capacity each with all

Rupees Three Paise

354 100.00 necessaryfittingsandconnectionetc.completeon 3.95 Ltr.

NinetyFive Only

Total of Plumbing Work (G)

Total Amount Of Civil Work, Borewell & General Development, Furniture Work,

Total Amount Of Civil Work, Borewell & General Development, Furniture Work,

Electrical Work, Elv Work, Plumbing Work

I/We am/are willing to carry out the work at………………….% above/below percent(Should be written in figures and words) of the estimated rate mentioned above.

Estimated amount put to tender Estimated amount put to tender

Deduct………% below Add………% Above

In words In words

The Contractor shall exhibit a board with detailed specification and details of work as directed by the Engineer-In-Charge for which no extra payment shall be made.

2 The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.

3 GST and Income tax TDS will be deducted at a source while making payments of bills

4 In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-10/2017 Cement Consumption/16/C Date:11/05/2017 as stated in

`Signature of Contractor with Seal Signature of Contracting Authority with Seal