Supply, Installation, Testing and Commissioning of Process Condenser Water Cooling System and Pipeline at Kerala State Drugs and Pharmaceuticals Ltd (KSDPL), Alappuzha

Amount

Cooling Tower

od147639/2023_2024 : Supply and Installation of I Cooling tower Advance Make, Model No 1RM37WB or equivalent. High efficiency low noise fans, EFF 1 motors sutiable for variable speed control, drive packages(Belt drive), FRP basin, Inspection door for cell, Quick fill and Float valve piping connection as integral part of the cooling tower . 57 CMH flow rate. Inlet temp 37 degC, Outlet 32 Deg C, wet bulb temp 28Deg C, Heat load capacity min 2,85,000 KCal/Hr

Cooling Tower Pumps

od151535/2023_2024 : Supply and Installation of End Suction Back pull out Centrifugal water pumpsets. Factory mounted on a common base with electric motor for recirculation of water for the central air conditioning system. The pump motor shall be suitable for 415 + 10% volts, 50 cycles/second, 3-phase power supply. The unit complete should be suitable for outdoor installation Total 180 US GPM & 25M Head

od151536/2023_2024 : Supply and Installation of Centrifugal End Suction Back pull out pump sets motor shall be suitable for 415 + 10% volts, 50 cycles/second, 3phase power supply. The unit complete should be suitable for outdoor installation. Capacity: 180 US GPM @ 15 Mts HEAD

od154020/2023_2024 : Supply and Installation of Centrifugal split casing end suction back pull-out pumps mounted on a common base with electric motor for recirculation of water for the central air conditioning system. The pump motor shall be suitable for 415± 10% volts, 50 cycles, phase AC Power supp. Capacity: 250 US GPM @ 15 Mts Head

Valves

od148099/2023_2024 : Automatic Butterfly Valve with Actuator:- Supply and Installation of two position pneumatic actuator Butterfly valve, as per the nominal flow rate in the circuit. Pressure rating min 8kg/cm2 50 MM

od148100/2023_2024 : Automatic Butterfly Valve with Actuator:- Supply and Installation of two position pneumatic actuator Butterfly valve, as per the nominal flow rate in the circuit. Pressure rating min 8kg/cm2 65 MM

od148101/2023_2024 : Automatic Butterfly Valve with Actuator:- Supply and Installation of two position pneumatic actuator Butterfly valve, as per the nominal flow rate in the circuit. Pressure rating min 8kg/cm2 80 MM

od148102/2023_2024 : Automatic Butterfly Valve with Actuator:- Supply and Installation of two position pneumatic actuator Butterfly valve, as per the nominal flow rate in the circuit. Pressure rating min 8kg/cm2 100 MM

od148111/2023_2024 : Supply and Installation of Non return valve, flange mounted/ wafer type pressure rating 8kg/cm2 100 MM

od148112/2023_2024 : Supply and Installation of Non return valve, flange mounted/ wafer type pressure rating 8kg/cm2 125 MM

od148113/2023_2024 : Supply and Installation of Ball valve MOC: SS 304, screwed end, 3 piece, manual actuated, pressure rating min 8kg/cm2. 15 MM

od148114/2023_2024 : Supply and Installation of Ball valve MOC: SS 304, screwed end, 3 piece, manual actuated, pressure rating min 8kg/cm2. 25 MM

od148115/2023_2024 : Supply and Installation of Ball valve MOC: SS 304, screwed end, 3 piece, manual actuated, pressure rating min 8kg/cm2. 32 MM

od148116/2023_2024 : Supply and Installation of Ball valve MOC: SS 304, screwed end, 3 piece, manual actuated, pressure rating min 8kg/cm2. 40 MM

od148117/2023_2024 : Supply and Installation of Butter fly valve with EPDM seat pressure rating 8kg/cm2 (min) MOC Stainless steel, manual actuated with lever Size 50 NB, end flange connected

od148118/2023_2024 : Supply and Installation of Butter fly valve with EPDM seat pressure rating 8kg/cm2, Wafer type.40 MM

od148119/2023_2024 : Supply and Installation of Butter fly valve with EPDM seat pressure rating 8kg/cm2, Wafer type.50 MM

od148120/2023_2024 : Supply and Installation of Butter fly valve with EPDM seat pressure rating 8kg/cm2, Wafer type.65 MM

od148121/2023_2024 : Supply and Installation of Butter fly valve with EPDM seat pressure rating 8kg/cm2, Wafer type. 80 MM

od148122/2023_2024 : Supply and Installation of Butter fly valve with EPDM seat pressure rating 8kg/cm2, Wafer type. 100 MM

od148123/2023_2024 : Supply and Installation of Butter fly valve with EPDM seat pressure rating 8kg/cm2, Wafer type.125 MM

Pipes

od147653/2023_2024 : Supply and Installation of Stainless steel pipe MOC Stainless steel, schedule 5s or better. Joined with argon welding with smooth matte finish or better. 40 MM

od147654/2023_2024 : Supply and Installation of Stainless steel pipe MOC Stainless steel, schedule 5s or better. Joined with argon welding with smooth matte finish or better. 50 MM

od147655/2023_2024 : Supply and Installation of Stainless steel pipe MOC Stainless steel, schedule 5s or better. Joined with argon welding with smooth matte finish or better. 65 MM

od147656/2023_2024 : Supply and Installation of Stainless steel pipe MOC Stainless steel, schedule 5s or better. Joined with argon welding with smooth matte finish or better.Surface finish needed to be matte finish at 20% of the lines and 80% of the lines to be polished finish 32 MM

od147657/2023_2024 : Supply and Installation of Stainless steel pipe MOC Stainless steel, schedule 5s or better. Joined with argon welding with smooth matte finish or better.Surface finish needed to be matte finish at 20% of the lines and 80% of the lines to be polished finish 40 MM

od147658/2023_2024 : Supply and Installation of Stainless steel pipe MOC Stainless steel, schedule 5s or better. Joined with argon welding with smooth matte finish or better.Surface finish needed to be matte finish at 20% of the lines and 80% of the lines to be polished finish 50 MM

od147659/2023_2024 : Supply and Installation of Stainless steel pipe MOC Stainless steel, schedule 5s or better. Joined with argon welding with smooth matte finish or better.Surface finish needed to be matte finish at 20% of the lines and 80% of the lines to be polished finish 65 MM

od147660/2023_2024 : Supply and Installation of Stainles steel Pipe Schedule 40 MOC SS304. Pressure rating min 4kg/cm2, joined with Argon welding above 50NB. Threaded joint for 50 NB and below. To be joined with MS and other metals by flanged joints with ready made heavy duty gasket. To be provided with reflective stickers for identification and color coding as directed by engineer in charge, at least every 6 meters of the line. Surface finish needed to be matte finish at 80% of the lines and 20% of the lines to be polished finish 15 MM

od147661/2023_2024 : Supply and Installation of Stainles steel bends Schedule 40 MOC SS304. Pressure rating min 4kg/cm2, joined with Argon welding above 50NB. Threaded joint for 50 NB and below. Surface finish needed to be matte finish at 80% of the lines and 20% of the lines to be polished finish 50 MM

od147662/2023_2024 : Supply and Installation of Stainles steel bends Schedule 40 MOC SS304. Pressure rating min 4kg/cm2, joined with Argon welding above 50NB. Threaded joint for 50 NB and below. Surface finish needed to be matte finish at 80% of the lines and 20% of the lines to be polished finish 65 MM

od147663/2023_2024 : Supply and Installation of Stainles steel Pipe Schedule 40 MOC SS304. Pressure rating min 4kg/cm2, joined with Argon welding above 50NB. Threaded joint for 50 NB and below. To be joined with MS and other metals by flanged joints with ready made heavy duty gasket. To be provided with reflective stickers for identification and color coding as directed by engineer in charge, at least every 6 meters of the line. Surface finish needed to be matte finish at 80% of the lines and 20% of the lines to be polished finish 25 MM

od147664/2023_2024 : Supply and Installation of Stainles steel Pipe Schedule 40 MOC SS304. Pressure rating min 4kg/cm2, joined with Argon welding above 50NB. Threaded joint for 50 NB and below. To be joined with MS and other metals by flanged joints with ready made heavy duty gasket. To be provided with reflective stickers for identification and color coding as directed by engineer in charge, at least every 6 meters of the line. Surface finish needed to be matte finish at 80% of the lines and 20% of the lines to be polished finish 32 MM

od147665/2023_2024 : Supply and Installation of Stainles steel Pipe Schedule 40 MOC SS304. Pressure rating min 4kg/cm2, joined with Argon welding above 50NB. Threaded joint for 50 NB and below. To be joined with MS and other metals by flanged joints with ready made heavy duty gasket. To be provided with reflective stickers for identification and color coding as directed by engineer in charge, at least every 6 meters of the line. Surface finish needed to be matte finish at 80% of the lines and 20% of the lines to be polished finish 40 MM

od147666/2023_2024 : Supply and Installation of Stainles steel Pipe Schedule 40 MOC SS304. Pressure rating min 4kg/cm2, joined with Argon welding above 50NB. Threaded joint for 50 NB and below. To be joined with MS and other metals by flanged joints with ready made heavy duty gasket. To be provided with reflective stickers for identification and color coding as directed by engineer in charge, at least every 6 meters of the line. Surface finish needed to be matte finish at 80% of the lines and 20% of the lines to be polished finish 50 MM

od147667/2023_2024 : Supply and Installation of Stainles steel Pipe Schedule 40 MOC SS304. Pressure rating min 4kg/cm2, joined with Argon welding above 50NB. Threaded joint for 50 NB and below. To be joined with MS and other metals by flanged joints with ready made heavy duty gasket. To be provided with reflective stickers for identification and color coding as directed by engineer in charge, at least every 6 meters of the line. Surface finish needed to be matte finish at 80% of the lines and 20% of the lines to be polished finish 65 MM

od147668/2023_2024 : Supply and Installation of MS 'C' class piping with SORF (Slip On Raised Face) flanges, with Stainless steel nut-bolts, supports with wooden block etc duly installed. (Condenser Water piping) (Welding for pipes above 50NB and threaded joints for pipe below 50 NB). No direct contact between dissimilar metals and the connection should use dielectric union when two dissimilar metals has to be connected. With 2 layers of anti corrosive paint and one layer of enamel paint. Sufficient areas has to be marked with flow direction arrows with reflective stickers and color coding as mentioned by the engineer in charge, at least every six meters of the line15 MM

od147669/2023_2024 : Supply and Installation of MS 'C' class piping with SORF (Slip On Raised Face) flanges, with Stainless steel nut-bolts, supports with wooden block etc duly installed. (Condenser Water piping) (Welding for pipes above 50NB and threaded joints for pipe below 50 NB). No direct contact between dissimilar metals and the connection should use dielectric union when two dissimilar metals has to be connected. With 2 layers of anti corrosive paint and one layer of enamel paint. Sufficient areas has to be marked with flow direction arrows with reflective stickers and color coding as mentioned by the engineer in charge, at least every six meters of the line25 MM

od147670/2023_2024 : Supply and Installation of MS 'C' class piping with SORF (Slip On Raised Face) flanges, with Stainless steel nut-bolts, supports with wooden block etc duly installed. (Condenser Water piping) (Welding for pipes above 50NB and threaded joints for pipe below 50 NB). No direct contact between dissimilar metals and the connection should use dielectric union when two dissimilar metals has to be connected. With 2 layers of anti corrosive paint and one layer of enamel paint. Sufficient areas has to be marked with flow direction arrows with reflective stickers and color coding as mentioned by the engineer in charge, at least every six meters of the line32 MM

od147671/2023_2024 : Supply and Installation of MS 'C' class piping with SORF (Slip On Raised Face) flanges, with Stainless steel nut-bolts, supports with wooden block etc duly installed. (Condenser Water piping) (Welding for pipes above 50NB and threaded joints for pipe below 50 NB). No direct contact between dissimilar metals and the connection should use dielectric union when two dissimilar metals has to be connected. With 2 layers of anti corrosive paint and one layer of enamel paint. Sufficient areas has to be marked with flow direction arrows with reflective stickers and color coding as mentioned by the engineer in charge, at least every six meters of the line40 MM

od147672/2023_2024 : Supply and Installation of MS 'C' class piping with SORF (Slip On Raised Face) flanges, with Stainless steel nut-bolts, supports with wooden block etc duly installed. (Condenser Water piping) (Welding for pipes above 50NB and threaded joints for pipe below 50 NB). No direct contact between dissimilar metals and the connection should use dielectric union when two dissimilar metals has to be connected. With 2 layers of anti corrosive paint and one layer of enamel paint. Sufficient areas has to be marked with flow direction arrows with reflective stickers and color coding as mentioned by the engineer in charge, at least every six meters of the line50 MM

od147673/2023_2024 : Supply and Installation of MS 'C' class piping with SORF (Slip On Raised Face) flanges, with Stainless steel nut-bolts, supports with wooden block etc duly installed. (Condenser Water piping) (Welding for pipes above 50NB and threaded joints for pipe below 50 NB). No direct contact between dissimilar metals and the connection should use dielectric union when two dissimilar metals has to be connected. With 2 layers of anti corrosive paint and one layer of enamel paint. Sufficient areas has to be marked with flow direction arrows with reflective stickers and color coding as mentioned by the engineer in charge, at least every six meters of the line65 MM

od147674/2023_2024 : Supply and Installation of MS 'C' class piping with SORF (Slip On Raised Face) flanges, with Stainless steel nut-bolts, supports with wooden block etc duly installed. (Condenser Water piping) (Welding for pipes above 50NB and threaded joints for pipe below 50 NB). No direct contact between dissimilar metals and the connection should use dielectric union when two dissimilar metals has to be connected. With 2 layers of anti corrosive paint and one layer of enamel paint. Sufficient areas has to be marked with flow direction arrows with reflective stickers and color coding as mentioned by the engineer in charge, at least every six meters of the line80 MM

od147675/2023_2024 : Supply and Installation of MS 'C' class piping with SORF (Slip On Raised Face) flanges, with Stainless steel nut-bolts, supports with wooden block etc duly installed. (Condenser Water piping) (Welding for pipes above 50NB and threaded joints for pipe below 50 NB). No direct contact between dissimilar metals and the connection should use dielectric union when two dissimilar metals has to be connected. With 2 layers of anti corrosive paint and one layer of enamel paint. Sufficient areas has to be marked with flow direction arrows with reflective stickers and color coding as mentioned by the engineer in charge, at least every six meters of the line100 MM

od147676/2023_2024 : Supply and Installation of MS 'C' class piping with SORF (Slip On Raised Face) flanges, with Stainless steel nut-bolts, supports with wooden block etc duly installed. (Condenser Water piping) (Welding for pipes above 50NB and threaded joints for pipe below 50 NB). No direct contact between dissimilar metals and the connection should use dielectric union when two dissimilar metals has to be connected. With 2 layers of anti corrosive paint and one layer of enamel paint. Sufficient areas has to be marked with flow direction arrows with reflective stickers and color coding as mentioned by the engineer in charge, at least every six meters of the line125 MM

Bends

od147843/2023_2024 : Supply and Installation of MS pipe bends with Galvanized coating (GI Pipes for drain line connections from the condenser water systems. Pressure rating min 2 kg/cm2 15 MM

od147844/2023_2024 : Supply and Installation of MS pipe bends with Galvanized coating (GI Pipes for drain line connections from the condenser water systems. Pressure rating min 2 kg/cm2 25 MM

od147845/2023_2024 : Supply and Installation of MS pipe bends with Galvanized coating (GI Pipes for drain line connections from the condenser water systems. Pressure rating min 2 kg/cm2 32 MM

od147846/2023_2024 : Supply and Installation of MS pipe bends with Galvanized coating (GI Pipes for drain line connections from the condenser water systems. Pressure rating min 2 kg/cm2 40 MM

od147847/2023_2024 : Supply and Installation of MS pipe bends with Galvanized coating (GI Pipes for drain line connections from the condenser water systems. Pressure rating min 2 kg/cm2 50 MM

od147848/2023_2024 : Supply and Installation of MS pipe bends with Galvanized coating (GI Pipes for drain line connections from the condenser water systems. Pressure rating min 2 kg/cm2 65 MM

od147849/2023_2024 : Supply and Installation of MS pipes with Galvanized coating (GI Pipes for drain line connections from the condenser water systems. Pressure rating min 2 kg/cm2 15 MM

od147850/2023_2024 : Supply and Installation of MS pipes with Galvanized coating (GI Pipes for drain line connections from the condenser water systems. Pressure rating min 2 kg/cm232 MM

od147851/2023_2024 : Supply and Installation of MS pipes with Galvanized coating (GI Pipes for drain line connections from the condenser water systems. Pressure rating min 2 kg/cm225 MM

od147852/2023_2024 : Supply and Installation of MS pipes with Galvanized coating (GI Pipes for drain line connections from the condenser water systems. Pressure rating min 2 kg/cm240 MM

od147853/2023_2024 : Supply and Installation of MS pipes with Galvanized coating (GI Pipes for drain line connections from the condenser water systems. Pressure rating min 2 kg/cm250 MM

od147854/2023_2024 : Supply and Installation of MS pipes with Galvanized coating (GI Pipes for drain line connections from the condenser water systems. Pressure rating min 2 kg/cm265 MM

od147855/2023_2024 : Supply and Installation of Stainles steel bends Schedule 40 MOC SS304. Pressure rating min 4kg/cm2, joined with Argon welding above 50NB. Threaded joint for 50 NB and below. Surface finish needed to be matte finish at 80% of the lines and 20% of the lines to be polished finish 15 MM

od147856/2023_2024 : Supply and Installation of Stainles steel bends Schedule 40 MOC SS304. Pressure rating min 4kg/cm2, joined with Argon welding above 50NB. Threaded joint for 50 NB and below. Surface finish needed to be matte finish at 80% of the lines and 20% of the lines to be polished finish 25 MM

od147857/2023_2024 : Supply and Installation of Stainles steel bends Schedule 40 MOC SS304. Pressure rating min 4kg/cm2, joined with Argon welding above 50NB. Threaded joint for 50 NB and below. Surface finish needed to be matte finish at 80% of the lines and 20% of the lines to be polished finish 32 MM

od147858/2023_2024 : Supply and Installation of Stainles steel bends Schedule 40 MOC SS304. Pressure rating min 4kg/cm2, joined with Argon welding above 50NB. Threaded joint for 50 NB and below. Surface finish needed to be matte finish at 80% of the lines and 20% of the lines to be polished finish40 MM

od147661/2023_2024 : Supply and Installation of Stainles steel bends Schedule 40 MOC SS304. Pressure rating min 4kg/cm2, joined with Argon welding above 50NB. Threaded joint for 50 NB and below. Surface finish needed to be matte finish at 80% of the lines and 20% of the lines to be polished finish 50 MM

od147662/2023_2024 : Supply and Installation of Stainles steel bends Schedule 40 MOC SS304. Pressure rating min 4kg/cm2, joined with Argon welding above 50NB. Threaded joint for 50 NB and below. Surface finish needed to be matte finish at 80% of the lines and 20% of the lines to be polished finish 65 MM

od147859/2023_2024 : Supply and Installation of MS C class Bends 90 degree 15 MM

od147860/2023_2024 : Supply and Installation of MS C class Bends 90 degree 25 MM

od147861/2023_2024 : Supply and Installation of MS C class Bends 90 degree 32 MM

od147862/2023_2024 : Supply and Installation of MS C class Bends 90 degree 40 MM

od147863/2023_2024 : Supply and Installation of MS C class Bends 90 degree50 MM

od147864/2023_2024 : Supply and Installation of MS C class Bends 90 degree 80 MM

od147865/2023_2024 : Supply and Installation of MS C class Bends 90 degree 125 MM

od147867/2023_2024 : Supply and Installation of MS C class Bends 90 degree 100 MM

od147868/2023_2024 : Supply and Installation of MS C class Bends 90 degree 65 MM

Cable Tray

4.6.1 : Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.100 mm width X 50 mm depth X 1.6 mm thickness Details of cost for 30 metres

4.6.2 : Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.150 mm width X 50 mm depth X 1.6 mm thickness

Cables and Terminations

od153630/2023_2024 : Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

od153631/2023_2024 : Supply and Installation of following cables including end termination for below listed XLPE insulated armoured cable with copper lugs, brass/PVC cable glands, tapping, crimping,ferruling etc. complete, to be included.6 Core 1.0 SQ. MM, Armoured ATC conductor multistranded, Shielded cable. (For Valve control)

od153632/2023_2024 : Supply and Installation of following cables including end termination for below listed XLPE insulated armoured cable with copper lugs, brass/PVC cable glands, tapping, crimping,ferruling etc. complete, to be included.4 Core 1.0 SQ. MM, Armoured ATC conductor multistranded, Shielded cable. (For Valve control)

od153633/2023_2024 : Supply and Installation of following cables including end termination for below listed XLPE insulated armoured cable with copper lugs, brass/PVC cable glands, tapping, crimping,ferruling etc. complete, to be included.2 Core 1.0 SQ. MM, Armoured ATC conductor multistranded, Shielded cable.

90.12.7.14 : Supply, laying, termination and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required. 3 core 10 sq mm

90.12.7.15 : Supply, laying, termination and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required. 3 core 16 sq mm

Pipe Insulation

od152030/2023_2024 : Supply and Installation of steam piping insulation inside the building with mineral rock wool insulation and aluminium cladding minimum density of 100 Kg per Cubic Meter as per IS 9842:1994 with 26 guage SS 304 cladding of thickness of 50mm as per IS 734-1967 with mounting accessories.Dia - 25 MM

od152031/2023_2024 : Supply and Installation of steam piping insulation inside the building with mineral rock wool insulation and aluminium cladding minimum density of 100 Kg per Cubic Meter as per IS 9842:1994 with 26 guage SS 304 cladding of thickness of 50mm as per IS 734-1967 with mounting accessories.Dia - 15 MM

od152275/2023_2024 : Supply and Installation of chilled water piping insulation inside the building with following closed cell elastomeric nitrile rubber of minimum 40-55 kg/cu m density.Thermal conductivity of 0.035 W/MK or better at 0 Deg mean temperature class insulation with factory laminated woven glass cloth applied by suitable rubber based adhesive.The insulation thickness of 25 mm thick upto 25 mm pipe,32 mm thick from 32 to 80 mm dia pipe,38 mm thick from 80 to 400 mm pipe.Dia - 125 MMThickness-38MM

od152277/2023_2024 : Supply and Installation of chilled water piping insulation inside the building with following closed cell elastomeric nitrile rubber of minimum 40-55 kg/cu m density.Thermal conductivity of 0.035 W/MK or better at 0 Deg mean temperature class insulation with factory laminated woven glass cloth applied by suitable rubber based adhesive.The insulation thickness of 25 mm thick upto 25 mm pipe,32 mm thick from 32 to 80 mm dia pipe,38 mm thick from 80 to 400 mm pipe.Dia - 80 MMThickness-32 MM

od152278/2023_2024 : Supply and Installation of chilled water piping insulation inside the building with following closed cell elastomeric nitrile rubber of minimum 40-55 kg/cu m density.Thermal conductivity of 0.035 W/MK or better at 0 Deg mean temperature class insulation with factory laminated woven glass cloth applied by suitable rubber based adhesive.The insulation thickness of 25 mm thick upto 25 mm pipe,32 mm thick from 32 to 80 mm dia pipe,38 mm thick from 80 to 400 mm pipe Dia - 65 MMThickness-32MM

od152280/2023_2024 : Supply and Installation of chilled water piping insulation inside the building with following closed cell elastomeric nitrile rubber of minimum 40-55 kg/cu m density.Thermal conductivity of 0.035 W/MK or better at 0 Deg mean temperature class insulation with factory laminated woven glass cloth applied by suitable rubber based adhesive.The insulation thickness of 25 mm thick upto 25 mm pipe,32 mm thick from 32 to 80 mm dia pipe,38 mm thick from 80 to 400 mm pipeDia - 40 MMThickness-32 MM

od152281/2023_2024 : Supply and Installation of chilled water piping insulation inside the building with following closed cell elastomeric nitrile rubber of minimum 40-55 kg/cu m density.Thermal conductivity of 0.035 W/MK or better at 0 Deg mean temperature class insulation with factory laminated woven glass cloth applied by suitable rubber based adhesive.The insulation thickness of 25 mm thick upto 25 mm pipe,32 mm thick from 32 to 80 mm dia pipe,38 mm thick from 80 to 400 mm pipe.Dia - 32 MMThickness-32 MM

od152282/2023_2024 : Supply and Installation of chilled water piping insulation inside the building with following closed cell elastomeric nitrile rubber of minimum 40-55 kg/cu m density.Thermal conductivity of 0.035 W/MK or better at 0 Deg mean temperature class insulation with factory laminated woven glass cloth applied by suitable rubber based adhesive.The insulation thickness of 25 mm thick upto 25 mm pipe,32 mm thick from 32 to 80 mm dia pipe,38 mm thick from 80 to 400 mm pipe. Dia - 25 MMThickness-25MM

od152283/2023_2024 : Supply and Installation of chilled water piping insulation inside the building with following closed cell elastomeric nitrile rubber of minimum 40-55 kg/cu m density.Thermal conductivity of 0.035 W/MK or better at 0 Deg mean temperature class insulation with factory laminated woven glass cloth applied by suitable rubber based adhesive.The insulation thickness of 25 mm thick upto 25 mm pipe,32 mm thick from 32 to 80 mm dia pipe,38 mm thick from 80 to 400 mm pipe. Dia - 15 MMThickness-25MM

od153178/2023_2024 : Supply and Installation of chilled water piping insulation inside the building with following closed cell elastomeric nitrile rubber of minimum 40-55 kg/cu m density.Thermal conductivity of 0.035 W/MK or better at 0 Deg mean temperature class insulation with factory laminated woven glass cloth applied by suitable rubber based adhesive.The insulation thickness of 25 mm thick upto 25 mm pipe,32 mm thick from 32 to 80 mm dia pipe,38 mm thick from 80 to 400 mm pipe. Dia - 50 MM, Thickness-32MM

od153179/2023_2024 : Supply and Installation of chilled water piping insulation inside the building with following closed cell elastomeric nitrile rubber of minimum 40-55 kg/cu m density. Thermal conductivity of 0.035 W/MK or better at 0 Deg mean temperature class insulation with factory laminated woven glass cloth applied by suitable rubber based adhesive. The insulation thickness of 25 mm thick upto 25 mm pipe,32 mm thick from 32 to 80 mm dia pipe,38 mm thick from 80 to 400 mm pipe. Dia - 100 MM Thickness-38 MM

od153180/2023_2024 : Supply and Installation of steam piping insulation inside the building with mineral rock wool insulation and aluminum cladding minimum density of 100 Kg per Cubic Meter as per IS 9842:1994 with 26 gauge SS 304 cladding of thickness of 50mm as per IS 734-1967 with mounting accessories. Dia - 50 MM

od153181/2023_2024 : Supply and Installation of steam piping insulation inside the building with mineral rock wool insulation and aluminium cladding minimum density of 100 Kg per Cubic Meter as per IS 9842:1994 with 26 guage SS 304 cladding of thickness of 50mm as per IS 734-1967 with mounting accessories.Dia - 40 MM

od153182/2023_2024 : Supply and Installation of steam piping insulation inside the building with mineral rock wool insulation and aluminium cladding minimum density of 100 Kg per Cubic Meter as per IS 9842:1994 with 26 guage SS 304 cladding of thickness of 50mm as per IS 734-1967 with mounting accessories.Dia - 32 MM

od153183/2023_2024 : Supply and Installation of Flexible flanged coupling with rubber bellows with pressure rating min 6kg/cm2.100 MM

od153184/2023_2024 : Supply and Installation of Flexible flanged coupling with rubber bellows with pressure rating min 6kg/cm2. 125 MM

Y Strainer

od151819/2023_2024 : Supply and Installation of Y strainer with both body and filter Stainless steel to be mounted with either flange/ threaded as per pipe size. Easily cleanable. Pressure rating min 8kg/cm2 32 MM

od151820/2023_2024 : Supply and Installation of Y strainer with both body and filter Stainless steel to be mounted with either flange/ threaded as per pipe size. Easily cleanable. Pressure rating min 8kg/cm2 40 MM

od151821/2023_2024 : Supply and Installation of Y strainer with both body and filter Stainless steel to be mounted with either flange/ threaded as per pipe size. Easily cleanable. Pressure rating min 8kg/cm2 80 MM

od151822/2023_2024 : Supply and Installation of Y strainer with both body and filter Stainless steel to be mounted with either flange/ threaded as per pipe size. Easily cleanable. Pressure rating min 8kg/cm2 50 MM

od151824/2023_2024 : Supply and Installation of Y strainer with Stainless steel filter units, to be mounted with either flange/ threaded as per pipe size. Easily cleanable. Pressure rating min 8kg/cm2 100 MM

od151825/2023_2024 : Supply and Installation of Y strainer with Stainless steel filter units, to be mounted with either flange/ threaded as per pipe size. Easily cleanable. Pressure rating min 8kg/cm2 125 MM

Guages

od152018/2023_2024 : Supply and Installation of Differential pressure switch, digital with display and output for variation in differential pressure. Range (0-3kg/cm2)

od152019/2023_2024 : Supply and Installation of Temperature gauge assembly, Dial type analog Temperature guage with glycerin filled dials , connected to the line with SS tubes and isolation valves 1/4" size NPT threaded. Measurement range 0-80 deg C

od152020/2023_2024 : Supply and Installation of Pressure gauge assembly, Dial type Pressure guage with glycerin filled dials , connected to the line with SS Siphon tubes and isolation valves 1/4" size NPT threaded. Measurement range 0-6 kg/cm2

Panel

Miscellaneous

od152257/2023_2024 : Integration of Heat Exchanger System with Cooling Tower and Commissioning of Process Condenser Water System.

od152258/2023_2024 : Supply and Installation of PT 100 temperature with well type immersed. Range -40 to 120 deg C , with temperature transmitter, with display at panel and dual set point tempreature controller.

od152259/2023_2024 : Supply and Installation of Air vent for removing air from the water lines, Lever operated size 25NB

od152260/2023_2024 : Supply and Installation of Air separator as per standard engineering parctices. Auto Air vents provided for releasing the air.

od153869/2023_2024 : Supply and Installation of Expansion tanks Pre charged. With approved butyl diaphragm as per standards. Working pressure minimum 12bar. Size as per the standard engineering practices

od154791/2023_2024 : AUTOMATIC FLOW CONTROLLER:- Design, Supply, Installation, Programming, Testing and Commissioning of automatic flow controller along with required control valves, Sensors, Temperature controllers, Solenoid valves/Actuators, panels, Remote Push buttons, necessary Electrical connections complete for controlling the flow of water from Plate Heat Exchanger 1 to Plate Heat Exchanger 2, when the fluid temperature is not below the desired level.

Structural Steel

od152286/2023_2024 : Supply and Installation of STEEL STRUCTURE MS Supports for Cooling towers, Pipe supports, etc with chequrred base plate and Pump stands with various Angle supports. I beams, C channels etc. (pipes not to be used for support) with 2 layers of anti corrosive paint and one layer of enamel paint, color as chosen by engineer in charge.

od152635/2023_2024 : Supply and Installation of Stainless-steel structure, for the support of SS pipes inside the GMP area. MOC, SS 304

RS ENGINEERING ENTERPRISES

SHES Air & Automation Pune

Bidder Name

RS ENGINEERING ENTERPRISES

SHES Air & Automation Pune

MM BABU ENGINEERING CONTRACTOR