SPECIAL REPAIR TO BLDG NO P-329 AND P-330 (OR MD ACCN) AT PMS UNDER GE (ARMY) TRIVANDRUM

Amount

S&F in repairs stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and directed.

M&L for rendering in two layers as 10mm thick with cement mortar (1:4) and finishing coat 5 mm thick with cement mortar (1:4) mixed with water proofing compound @ 3% by the weight of cement on fair faces of brick work in external surfaces of wall finished even and smooth without using extra cement complete all as specified and directed. Note: Water proofing compound will be measured and paid separately.

M&L for finishing walls with acrylic smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified and directed.

M&L for rendering 10 mm thick cement plaster in cement mortar 1:4 on fair faces of brick work/ PCC solid block masonry/ concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparing new plastered surfaces, applying priming with alkali resistant priming paint and applying two coats of distemper oil emulsion complete all as specified and directed.

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing rubbish off the premises complete all as specified and as directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15cm thickness (below or above ground level) and removing debris outside MD land complete all as specified and as directed.

M&L for 75mm thick PCC 1:3:6, Type C2 (using 40mm graded stone aggregate) as in plinth protection, hard standing, finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6, Type C2 (using 40mm graded stone aggregate) as in sub base of floor complete all as specified and directed.

M&L for screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:6 for laying floor finishes complete all as specified and directed.

M&L for 10 mm thick screed bed in cement mortar 1:4 on stone/ brick masonry surfaces for skirting, dado complete all as specified and directed.

M&L for glazed ceramic coloured joint free non skid tiles in vertical surface 450 x 300 x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specified and directed.

M&L for Chequered cement concrete tiles 400 x 400 x 25 mm thick, coloured set, jointed and pointed in neat cement slurry in floors with grey cement and pigment complete all as specified and directed.

Supply only integral water proofing compound.

M&L for preparing old wall surfaces by washing, rubbing down, stopping and applying two coats of oil bound distemper complete all as specified and directed.

M&L for applying one coat of Alkali & fungal resistance, dirt resistance exterior acrylic exterior emulsion water proofing painting including preparation of old surfaces of wall as per manufacturer's instructions etc complete all as specified and directed.

S&F Rotational moulded polyethylene water storage tanks of 500 ltrs capacity, triple layer (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I and 20 mm bore ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed including dismantling of existing unserviceable water tank and connecting inlet and outlet pipe lines complete all as specified and directed.

S&F 15 mm bore unplasticised PVC pipes and fittings of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., including taking up or down old PVC pipe complete all as specified and directed.

S&F 20 mm bore unplasticised PVC pipes and fittings of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., including taking up or down old PVC pipe complete all as specified and directed.

S&F in repairs PVC connections 15mm size, 450mm length with 02 Nos brass check nuts with washer etc complete all as specified and directed.

S&F in repairs bib tap cast copper alloy, chromium plated, fancy type, with crutch or butterfly handle, screwed down, screwed for 15mm bore dia iron pipe/ PVC pipe or for brass ferrule complete all as specified and directed.

S&F in repairs stop valve, cast copper alloy, chromium plated, fancy type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for unions or fixed for 15mm bore dia of pipe complete all as specified and directed.

Taking down shutters of any description exceeding 1 sq.m and not exceeding 2 sq.m each complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exceeding 1.50 Sq.m but not exceeding 4.00 Sqm each, and removing from site, complete all as specified and directed.

M&L for second class hardwood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and directed.

M&L for second class hardwood 35 mm thickness plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

M&L for second class hardwood glazed and skeleton shutters 35 mm thick, open rebated and prepared to receive glass, gauze, etc., without sash bars, chamfered or rounded,mitred and rebated sash bars,any numbers fitted with cut and mitred beads for securing glass, etc. sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); and fitted to chowkats complete all as specified and as directed.

Taking down shutters of any description not exceeding 1 sq.m each and refixing the same opening after easing and adjusting and also refixing builders hardware as required including renewal of unserviceable screws, etc. complete all as specified and directed.

M&L for second class hardwood glazed and skeleton shutters 30 mm thick of windows, ventilators, etc. are provided with stiles and rails, , open rebated and prepared to receive glass, gauze, etc., (without sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (b); supplied and fitted to chowkats complete all as specified and as directed.

M&L for preparation of new wooden surfaces of any description not otherwise described, exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and directed.

S&F continuous (piano) hinges, mild steel, bright finish or electrogalvanised, 30 mm width of flaps (when open) complete all as specified and directed.

M&L for 18/ 19 mm thick prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber/ aluminium frame work complete all as specified and directed.

S&F 100mm size aluminium anodised hasp and staple, safety type with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

S&F aluminium alloy, anodised, sliding door bolt length 300mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and directed.

S&F 100 mm size aluminium handles, cast type, anodised complete all as specified and directed.

S&F 150 mm size aluminium handles, cast type, anodised complete all as specified and directed.

S&F 100 mm size butt hinges, medium weight, cold rolled mild steel complete all as specified and directed.

S&F 100 mm long aluminium anodised, barrel tower bolts of extruded section complete all as specified and directed.

S&F 150 mm long aluminium anodised, barrel tower bolts of extruded section complete all as specified and directed.

S&F 75 mm size butt hinges, medium weight, cold rolled mild steel complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exceeding 1.50 Sqm each, and removing from site, complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Paneling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, fixing in opening as per specification & drawing complete all as specified and directed.

S&F 100 mm size Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-22 complete all as specified and directed.

S&F 125 mm size aluminium handles, cast type, anodised complete all as specified and directed.

S&F in repairs PVC coated mild steel conduit pipe 25 mm bore (Drapery rod) with a pair of PVC coated MS clamps to hold drapery rod and decorative attachment at one end or both ends of drapery rod, fixed to opening of doors/ windows, (Each opening not exceeding 1.50 mtr, contained with a pair of clamps and a pair of side ornamental attachments) complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed.

M&L for 4 mm thick non-asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Aluminium framework with screws, fixed in jointless finish with jointing compound and jointing tape as per manufacturer instructions complete all as specified and as directed.

S&F anodised aluminium snap grid frame work (size of grid 605x605 mm) for false ceiling work complete all as specified and as directed.

S&F 2.50 mm dia. plain mild steel wire, galvanised class 3, in detached work such as for hangers and fixing to straining bolts, hooks, eyes, etc. as directed (each line of wire to be measured)

S&F in repairs Vitreous China wash basin, white, flat back, size 550x400mm including cutting for and pinning in ends of brackets or erecting stand, waste pipe and connected fittings complete all as specified and directed.

S&F in repairs PVC (SWR) floor trap, outlet 75 mm dia, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F in repairs pillar taps of size 15mm bore dia, brass with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered hot or cold with long screwed shanks and fly-nuts screwed for iron pipe complete all as specified and directed.

S&F in repairs 15 mm bore dia. angle cock cast copper alloy, chromium plated, fancy type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed.

M&L for 32 mm dia. waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed including taking down old existing waste fittings complete all as specified and directed.

S&F in repairs health faucet, brass, chromium plated including flexible PVC pipe with steel lining of 1 mtr long, chromium plated, with push button suitable for 15mm pipe complete all as specified and directed.

S&F in repairs vitreous china wash down water closet pan (pedestal pattern), white, including fixing bolt, seat cover (excluding flushing cistern and flush pipe) including connection to drain (or outgoing pipe) and to flushing pipe, anti syphonage etc complete all as specified and directed.

S&F in repairs 10 ltrs capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and connection to flush pipe complete all as specified and directed.

S&F in repairs grating doom 125 mm dia cast copper alloy, chromium plated with waste hole, making good to floor complete all as specified and directed.

S&F in repairs Aluminium anodised tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed.

S&F PVC ventilator fixed type with solid frame of size 70mm x 45mm including louvers, frosted glass 3mm thickness, including MS guard bars of 10mm dia spacing 150 mm C/C and stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with PVC beading including synthetic enamel painting to steel surfaces. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size, including taking down old ventilator complete all as specified and directed.

S&F in repairs shower rose, brass, chromium plated 125mm size with or without swivel joints, fixed to steel pipe or union complete all as specified and directed.

Demolition of brick or stone /boulder masonry built in cement mortar or cement lime mortar, including all quoins, arches, pillars etc. but excluding ashlar facings, dressed stone work and pre cast concrete articles and removing debris outside MD land complete all as specified and as directed.

M&L for pre-cast cement concrete 1:3:6 type C1 (using 20mm graded stone aggregate) block masonry with solid blocks, exceeding 10 cm in width and setting in CM 1:6 complete all as specified and directed.

S&F in repairs stainless steel plate rack of size 90x78x23cm using 1mm thick SS sheet, standard pattern complete all as specified and directed.

Excavating in trenches in hard/ dense soil, not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exceeding 10 sq m on plan and not exceeding 1.5 m in depth and getting out complete all as specified and directed.

Demolition and breaking up 100/ 110 mm internal dia drain pipes (Salt glazed ware, AC or reinforced concrete) set in cement mortar complete all as specified and directed.

Demolition and breaking up 150/ 160 mm internal dia drain pipes (Salt glazed ware, AC or reinforced concrete) set in cement mortar complete all as specified and directed.

Taking down 75/80 mm bore PVC pipes including all fittings with spigot and socket ends and cement or rubber gasket joint complete all as specified and directed.

Taking down 100/ 110 mm bore PVC pipes including all fittings with spigot and socket ends and cement or rubber gasket joint complete all as specified and directed.

M&L for plain cement concrete PCC 1:4:8, type D2, using 40mm graded broken stone aggregate as in foundation of manhole including necessary form work complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L for precast cement concrete 1:2:4 type B1, using 20mm graded stone aggregate as in manhole / Gully trap cover slab set in CM 1:4 including use and waste of necessary form work complete all as specified and directed.

M&L for TMT steel bars 6 to 8 mm dia as in reinforcement for concrete, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for rendering 10 mm thick in CM 1:3 on brick work or concrete surfaces mixed with WPC @ 3% by weight of cement, finished even and smooth without using extra cement complete all as specified and directed. Note- WPC will be measured and paid separately.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm using soil obtained from excavation complete all as specified and directed.

Removing excavated material to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

M&L for PVC (SWR) gully trap 110 mm dia, setting and jointing with solvent cement including taking down old trap complete all as specified and directed.

S&F in repair 75 mm bore, PVC (SWR) bend any radius complete all as specified and directed.

S&F in repair 75 mm bore, PVC (SWR) bend any radius with access door complete all as specified and directed.

S&F in repair 110 mm bore, PVC (SWR) bend any radius complete all as specified and directed.

S&F in repair 110 mm bore, PVC (SWR) bend any radius with access door complete all as specified and directed.

S&F in repair 75 mm bore, PVC (SWR) branch piece, single (single Y) equal or unequal complete all as specified and directed.

S&F in repair 110 mm bore, PVC (SWR) branch piece, single (single Y) equal or unequal complete all as specified and directed.

S&F in repairs PVC (SWR) junction, single (Single T) equal or unequal for 75mm bore dia pipe complete all as specified and directed.

S&F in repairs PVC (SWR) junction, single (Single T) equal or unequal for 110mm bore dia pipe complete all as specified and directed.

S&F in repairs 75 mm bore PVC (SWR) vent cowl complete all as specified and directed.

Cutting holes in brick walls built in cement mortar of depth exceeding half brick but not exceeding one brick, for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 using 40mm graded stone aggregate as concrete bed to drain pipe 100/ 110 mm dia bore including packing under and haunching against the sides of pipe after they are laid and tested complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 using 40mm graded stone aggregate as concrete bed to drain pipe 150/ 160 mm dia bore including packing under and haunching against the sides of pipe after they are laid and tested complete all as specified and directed.

S&F 110 mm bore PVC (SWR) pipes, single socketed, in any length with rubber ring joints or jointing with solvent cement, laid in trenches or in floors complete all as specified and directed.

S&F 160 mm bore PVC (SWR) pipes, single socketed, in any length with rubber ring joints or jointing with solvent cement, laid in trenches or in floors complete all as specified and directed.

S&F 110 mm bore PVC (SWR) pipes, single socketed, in any length with rubber ring joints or jointing with solvent cement, fixed to walls complete all as specified and directed.

S&F 75 mm bore PVC (SWR) pipes, single socketed, in any length with rubber ring joints or jointing with solvent cement, fixed to walls complete all as specified and directed.

Taking down carefully copper/aluminium point wiring of light, fan, socket or power socket complete, including fittings such as switches, ceiling roses, pendants, regulators, sockets etc. and making good disturbed surfaces of walls, floor ceiling etc, match the existing complete all as specified and directed

M&L for point wiring complete for one light point controlled by one switch with 1.5 sqmm single core PVC insulated unsheathed FRLS cable 1100 volts grade with multi stranded, copper conductor partly concealed in wall through PVC conduit and conduit accessories and partly surface on ceiling/ roof through PVC conduit and accessories of suitable size with modular metal flush boxes of suitable size & modules, concealed in walls with modular white plated cover as top cover fixed with screws for housing switches, socket outlets, fan regulators etc, multistranded single core green colour copper conductor for earth continuity connected to earth dolly all as specified and directed Note: Cost of modular metal flush boxes concealed in wall with suitable white cover plate for mounting switches/ sockets, regulators, bell push etc and cost of cutting chases & making good to disturbed surface with cement mortar, if required any shall be deemed to be included in the quoted rate.

All as per item No. 98.00 here in before but for one fan point controlled by one way switch and regulator complete all as specified and directed.

All as per item No. 98.00 here in before but for one bell/ buzzer point controlled by one bell push button complete all as specified and directed.

All as per item No. 98.00 here in before but for One 3 Pin, 5 Amps socket outlet on same board with other switches/ sockets complete all as specified and directed.

All as per item No. 98.00 here in before but for One 3 Pin, 5 Amps socket outlet on independent board complete all as specified and directed.

All as per SI item No. 98.00 here-in-before, but for one switch socket outlet, 3 pin 16 Amp on independent board with 4.00 Sqmm FRLS cable and 4.00 sqmm cable earth continuity wire complete all as specified and directed.

S&F modular switch 1 way 6A, 1 module, 240 Volts complete all as specified and directed.

S&F modular switch 1 way 16A, 1 module, 240 Volts complete all as specified and directed.

S&F Modular Bell push 6A, 1 module, 240 Volts complete all as specified and directed.

S&F modular fan step regulator, 120W - 2 module, 240 Volts, 50 Hz complete all as specified and directed.

S&F modular socket, 6A - 2/3 pin combined 2 module, flush type complete all as specified and directed.

S&F modular socket 6A/16A - 2/3 pin combined 2 module, flush type complete all as specified and directed.

S&F ceiling rose, 3 terminals PVC/ polycarbonate, isolated body complete all as specified and directed.

M&L for lamp holder, PVC/Polycarbonate type with back plate suitable for angle/ batten fittings complete all as specified and directed.

M&L for Buzzer, Ding Dong AC, 230 volts, single pole complete all as specified and directed.

M&L for distribution board, vertical, made out of sheet metal enclosure (CRCA sheet) dust and vermin proof, double door, VTPN 4 way, 415 volts grade with insulated rated bus bar with nickel plated brass, isolated neutral bar and door earthing, earth bar IP- 43 protection with poly urethane (PU) gasketing, IK-08 Mechanical impact resistance, door earthing flush to wall, including testing suitable for fixing MCCB, MCB TP/SPN/SP etc, including taking down existing unserviceable one and removing from site complete all as specified and directed.

S&F in replacement of MCCB triple pole and neutral (four pole) 100 Amp, 415 volts, 50 Hz, having thermal setting range 70% to 100% and adjustable magnetic setting and breaking capacity 16 KA including making incoming and outgoing connections complete all as specified and directed.

M&L for distribution board, vertical, made out of sheet metal enclosure (CRCA sheet) dust and vermin proof, double door, SPN 8 way, 240 volts grade with 200 Amps insulated rated bus bar with nickel plated brass, isolated neutral bar and door earthing, earth bar IP- 43 protection with poly urethane (PU) gasketing, IK-08 Mechanical impact resistance, door earthing flush to wall, including testing suitable for fixing MCCB, MCB TP/SPN/SP etc, including taking down existing unserviceable one and removing from site complete all as specified and directed.

S&F MCB single pole 5 to 32 Amps current carrying capacity, 240 volt rating, 10 KA, C curve with IP-20 protected terminals including contact indication window, IP-20 protection, energy limitation Class-3, airflow channels on both sides, bi-connect terminals etc., complete with connection, testing and commissioning and taking down old one from the site complete all as specified and directed.

S&F MCB single pole 40 Amps current carrying capacity, 240 volt rating, 10 KA, C curve with IP-20 protected terminals including contact indication window, IP-20 protection, energy limitation Class-3, airflow channels on both sides, bi-connect terminals etc., complete with connection, testing and commissioning and taking down old one from the site complete all as specified and directed.

S&F MCB SPN 6 to 32 Amps current carrying capacity, 240 volt rating, 10 KA, C curve with IP-20 protected terminals including contact indication window, IP-20 protection, energy limitation Class-3, airflow channels on both sides, bi-connect terminals etc., complete with connection, testing and commissioning and taking down old one from the site complete all as specified and directed.

Taking down carefully existing serviceable Ceiling fan/Wall mounted fan, ceiling cable end, etc., removing the fan for keeping in safe custody, hanging the ceiling fan with down rod after rewiring including clamps, hooks, hold fasteners etc and connecting up, including making electric connection from ceiling rose or connector to fan complete all as specified and directed.

S&F smart extruded aluminium LED batten (4ft) type light fittings with higher efficacy 1x 20W, 220V, AC decorative box type with driver, warm/cool white (as directed by Engr-in-Charge), double sided connection, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose, including taking down existing unserviceable one and removing from site complete all as specified and directed. Make: Bajaj Cat No. BCLAB 20W LED PS or equivalent make of Philips/Wipro/Osram/GE/Havells/ Jaguar/BENLO/HALONIX

S&F LED light fitting mirror type with high output diffuser 2 feet, 10 watts, 220 V, AC decorative type with warm/cool white (as directed by Engr-in-Charge), driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F LED street light fitting 35 Watts, 230 V, AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection, including taking down existing unserviceable light fitting and removing from site complete all as specified and directed.

M&L for sub-main wiring with 2 runs of 6 sqmm single core PVC insulated, FRLS, unsheathed cable with stranded copper conductor, 1100 Volts grade drawn through and including PVC conduit with all fitting such as Tees, Bends, Elbows, etc., fixed surface on wall/ceiling including 6 Sqmm multistranded PVC insulated, FRLS, copper conductor cable as earth continuity conductor and connecting to common earth dolly, including taking down complete all as specified and directed. NOTE: Two runs of 6.0 sqmm copper cables and one run of 6.0 sq mm copper cable along with white colour PVC conduit/ conduit accessories will be measured as one unit length.

M&L for Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6.3mm thick buried directly in ground vertically to a depth not less than 2.25 metre below ground level with top edge of earth plate at a depth of not less than 1.5 metre below normal ground level, connected to galvanised earth lead of GI wire of size 4mm dia by means of GI Bolts, Nuts, check nuts and washers of the earth and thimbles and other end of the earth strip connected to earthing test point and protected by galvanised iron pipe light grade 15mm dia from earth plate to Panel/DBs and water pipe 20mm dia GI medium grade raised up to a level of 50cm above ground level with plug at top, earthing pit in PCC (1:3:6) type C-1 RCC pre-cast (1:2:4 type B-1) cover slab of 50 mm thick using 8.00mm dia CTD bars reinforcement both ways at 140 mm centre to centre with handle, 20 mm dia GI pipe medium grade for watering pipe, wire mesh, funnel and providing charcoal or coke and salt in alternative layers of 15 cm including necessary earth work in any type of soil, returning, refilling and removing of surplus soil to a distance not exceeding 50 mtr testing complete all as shown in electrical plate No-3 of MES Schedule Part-I of SSR-2009 complete all as specified and directed, including taking down existing unserviceable earthing complete all as specified and directed.

S&F light fitting of frosted glass type with chrome finish wall lamp 1 x 4 Watts, warm white, body dark grey colour, aluminium die-cast with IP-65 protection with LED bulb complete including taking down existing unserviceable one and removing from site complete all as specified and directed.

S&F LED light fittings 1 x 20 W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

M/S AMBATTU CONSTRUCTIONS (BID ID -3266610)

SUPER COOL (BID ID -3266704)

KEERTHI CONSTRUCTIONS (BID ID -3260245)

DJ GROUP (BID ID -3264018)

PINKATRON SECURITIES PRIVATE LIMITED (BID ID -3261210)