ADDITION ALTERATION OF CERTAIN OFFRS JCOS/OR MARRIED ACCN AT LANSDOWNE

Amount

Demolition of brickwork or stone boulder masonry built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n. exc 15 cm thickness (below or above ground level ) and removing unserviceable material,outside of A 1 defence land complete all as specified and directed.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) in roofs,floors (other than ground floors),shelves,beams,staircases,landing,chajjas and removing unserviceable material,outside of A 1 defence land complete all as specified and directed.

Excavation in trenches,not exceeding 1.5 M wide and not exceeding 1.5 M depth; for foundation etc and getting out in soft/disintegrated rock. complete all as specified and directed.

Excavation over area not exceeding 1.5metre depth and getting out in hard/dense soil complete all as specified and directed

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in soft/disintegrated rock all as specified and directed

M&L Plain Cement concrete Type D-2, 1:4:8 (using 40mm graded stone aggregate), as in foundation, filling and mass concrete complete all as specified and directed.

M&L Walling of Random rubble masonary, well bonded,bedded and solidly hearted ,brought upto courses,built in cement mortar 1:6 complete all as specified and directed.

All as per ser item No 08 here-in-before but except stones.complete all as specified and directed. Note: old serviceable stones as obtained from demolition under item No-01 here-in-before will be used.

M&L Brickwork with sub class ‘B’ (old size) bricks, straight or curved on plan exceeding 6 metre mean radius built in cement sand mortar 1:6 complete all as specified.

All as per item here-in-before but except bricks. Note: old serviceable bricks as obtained from demolition under item No-01 here-in-before will be used.

Returning filling in with approved excavated earth, incl spreading leveling, watering and well ramming in layers n exc 25 cm thick as in soft/loose soil complete all as specified and directed.

Removing of excavated soil n exc 50m and depositing where directed at a level not exc 1.5 M above the starting point complete all as specified and directed.

M & L RCC ( nominal mix ) type A-1, 1:1½::3 ( using 20 mm graded stone agg) as in beams, cantilevers, bressumers, lintels over 1.5 m span.complete all as specified and directed.

M&L use and waste of form work to side and soffits of floor or roof beams, litels flat rough finished complete all as specified and directed.

M&L for TMT bar 10 mm and over cut to length, bend to shape required including cranking, bending spirally for hoopings for cols, hooking ends and binding with ad including mild steel wire (annealed) not less than 0.9 mm dia.complete all as specified and directed.

M&L for TMT bars 6 to 8 mm dia and over cut to length bent to shape required including cranking bending spirally for hooping for columns hooking end and binding with and incl mild steel wiere (annealed) not less than 0.9 mm dia or securing with clips.complete all as specified and directed.

All as per srl item no 17 above but 5 to 10 mm dia bar as in stirrups,ties.

M&L for Pre fabricated factory made RCC manhole cover (RCC 1:2:4 Type B-1 (using 20 mm graded crushed stone aggregate) as in man hole cover including necessary form work except slab set in CM 1:4 complete all as specified and directed.

Supply only liquid water proofing compound.(ISI marked) complete all as specified and directed.

Taking down cement plaster of any description including raking out joints, hacking for key, scrubbing down with water etc a and removing unserviceable material,outside of A 1 defence land complete all as specified and directed.

M&L hard core of broken stone or boulders of guage n.exc, 63mm, deposited, spread and levelled in layers n.exc, 15 cm thick, watered and rammed to a ture surface.complete all as specified and directed.

M&L for 75mm thick PCC 1:4:8, type D-2 using 40 mm graded stone aggregate, as in sub base for pavement, path etc.complete all as specified and directed.

M&L for 25 mm thick PCC 1:2:4 type B-0, using 12.5 mm graded stone aggregate, including finishing surface of concrete topping even and rough complete all as specified and directed.

Material & labour for Rendering 12 mm thick CM 1:6 on brick or concrete surfaces finished even & fair without using extra cement complete all as specified and directed.

M & L for Rendering 15 mm thick in two layers i.e. 10mm thick in CM 1:6 and 5mm thick in CM 1:4 using water proofing liquid compound as per manufacturer's instructions on other than fair faces brick or concrete surfaces and finishing surfaces even & fair without using extra cement complete all as specified and directed. Note :- Water proofing liquid compound shall be measured and paid separately.

Material & labour for Rendering 5 mm thick CM 1:3 on brick or concrete surfaces of ceiling /chajja's finished even & smooth without using extra cement complete all as specified and directed.

Material & Labour for 300x300x 7 to 8mm thick:- Non-Skid light coloured ceramic tiles of any design and pattern, 7 to 8 mm thick (Square/rectangular) area of each tiles exceeding 0.06 Sqm and not exc. 0.11 Sqm, in floor etc. Set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles. Tiles shall be confirming to IS-15622.2006, Group B II with average water absorption between 3% to 6%. Length, width and straightness of sides + 0.10% (Max deviation). Thickness + 5.0% (Max deviation). Centre & Edge curvature and warpage + 0.50% (Max deviation). Breaking strength 1000 N (Minimum) and minimum 95% tiles shall be free from visible defects. including 15 mm thick screed bed in cm 1:6 including dismantling of existing old tile. complete all as specified and directed. Note:- Shade of the tiles including Colour, design and pattern shall be approved by AGE(I)

Material & Labour for 300X450X 8 to 9 mm thick joint free light coloured glazed ceramic tiles of any design and pattern, as in dado etc. Set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles. Tiles shall be confirming to IS-15622:2017, Group B III with average water absorption between 10% to 15%. Length, width and straightness of sides + 0.20% (Max deviation). Thickness + 4.0% (Max deviation). Straightness of sides and Rectangularity +0.15% (Max Deviation). surface flatness + 0.22% (Max deviation). Breaking strength 500 N (Minimum) and minimum 95% tiles shall be free from visible defects over and including 10 mm thick in cm (1:4) backing coat and including dismantling of old tiling and removing old unserviceable materials from the distance not exceeding 1.5 Km complete all as specified and directed. Note:- Shade of the tiles including Colour, design and pattern shall be approved by AGE(I) Lansdowne

Material & Labour for 400x400x 7 to 8mm thick Joint free Non-Skid light coloured ceramic tiles of any design and pattern, 7 to 8 mm thick (Square/rectangular) area of each tiles exceeding 0.06 Sqm and not exc. 0.11 Sqm, in floor etc. Set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles. Tiles shall be confirming to IS-15622.2006, Group B II with average water absorption between 3% to 6%. Length, width and straightness of sides + 0.10% (Max deviation). Thickness + 5.0% (Max deviation). Centre & Edge curvature and warpage + 0.50% (Max deviation). Breaking strength 1000 N (Minimum) and minimum 95% tiles shall be free from visible defects over and including 15 mm thick screed bed in cm 1:6 including dismantling of existing old tile. complete all as specified and directed. Note:- Shade of the tiles including Colour, design and pattern shall be approved by AGE(I)

Material & Labour for 600X600X 9 to 10 mm thick Joint free double charged Vitrified tiles of any design and pattern as in floor etc. Set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles. Tiles shall be confirming to IS-15622:2017, Group B1b with average water absorption between 0.08% to 3%. Length, width and straightness of sides + 0.10% (Max deviation). Thickness + 4.0% (Max deviation). Centre & Edge curvature and warpage + 0.20% (Max Deviation). Breaking strength 1200 N (Minimum) and minimum 95% tiles shall be free from visible defects over and including and over screed bed or bedding layer of mortar 15mm thick for laying of floor finishes in CM 1:6 including dismantling of existing old tile, and removing old unserviceable materials from the distance not exceeding 1.5 Km complete all as specified and directed. Note:- Shade of the tiles including Colour, design and pattern shall be approved by AGE(I)

Dismantling wrought iron or mild steel work of any description not other wise provided for.complete all as specified and directed.

S&F in repairs PVC ( SWR ) floor trap ( ISI Marked) of 75mm dia of outlet, plain with grating including jointing with solvent cement.

S&F PVC (SWR ) bend of 75 mm bore ( ISI Marked) pipe of any radius.complete all as specified and directed.

All as per sl item no 34 above but with access door ( ISI Marked).complete all as specified and directed.

S&F in repairs PVC ( SWR ) waste pipe pipe ( ISI Marked) of 75 mm dia bore in any length ,single socketed with rubber ring joints laid in trenches or in floors.complete all as specified and directed.

All as per sl item 36 above but 110mm dia ( ISI Marked).

S&F PVC ( SWR ) 'P'/'S' trap 110mm bore ( ISI Marked) as required. complete all as specified and directed.

S&F PVC ( SWR ) junction single,(single T) equal or unequal 110mm bore with access door ( ISI Marked) .complete all as specified and directed.

S&F PVC ( SWR ) junction single,(single T) equal or unequal 75mm bore with access door.complete all as specified and directed.

S&F PVC ( SWR ) reducer 110mm bore ( ISI Marked) .complete all as specified and directed.

S&F PVC ( SWR ) vent cowl 75mm bore ( ISI Marked). complete all as specified and directed.

S&F PVC ( SWR ) waste pipe of 75 mm dia bore in any length ( ISI Marked) ,single socketed with rubber ring joints fixed to walls with necessary MS fixtures i.e 50mmx 5 mm flat iron and 16 mm dia round iron stays including bolts and nuts and securing ends of stays to walls or roof complete all as specified and directed.

S&F as in repairs grating doom 100mm dia ( ISI Marked) with waste hole of PTMT (Min. Wt. 25 gram ) complete all as specified and directed.

S&F as in repairs grating doom 125mm dia with waste hole of PTMT ( ISI Marked) (Min. Wt. 40 gram ) complete all as specified and directed.

Dismantling timber scantling 40 sqcm and over in section,in any position, any description complete all as specified and directed.

All as per Item No.46 above in fillets, rails, posts, rafters,purlins, etc. under 40 sq. cm in section in any description

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) of size not exc 1.5 Sqm each and removing from site complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) of size exc 1.5 Sqm but not exc 4 sqm each and removing from site complete all as specified and directed.

Taking down shutters of any description, area exceeding 1 sqm and not exceeding 2.00 sqm each complete all as specified and directed.

S & F for 2nd Class Hardwood ( SAL) in Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered,put together with glue pinned at joints complete all as specified and directed.

M & L for 2nd class softwood in timber scantling for wall panelling, ceiling, roof truss,post, purlins, rafters and similar work (Clean sawn Timber framed and fixed type) including necessary coating framed joints with glue, complete all as specified and directed.

S& Fixing as in repairs 2nd Class softwood 20mm thick as in Eaves Boarding,ceilings,soffits etc, clean sawn planed one side with butt joints & fixed with nails in any situation, including replace old and decayed boarding in patches including cutting out old ,piecing,heading joints,etc complete all as specified and directed.

S& F for 35mm thick, IInd class hard wood (SAL) plain, framed, panelled factory made shutters ( ISI Marked) (two panel) with lock rail and panel of 12mm veneered particle board with commercial veneering on both faces. The size of rails and styles as per IS-1003 (Part-I) kiln seasoned and chemically pressure treated complete all as specified and directed. Note:- Before procurement of door the contractor has to produce the sample of door(factory made) for approval and refernce

S& F for 30 mm thick 2nd class HW glazed and skelton factory made door shutters(SAL) ( ISI Marked) open rebated with sash bar and prepared to receive wire gauge edges cut and mitred beads for securing glass etc size of members of shutters as specified in SSR Part I section and clause 8.20 (a) fitted to chowkats or frames of any numbers of panels complete all as specified and directed.Note:- Before procurement of door the contractor has to produce the sample of door(factory made) for approval and refernce

S&F for 30 mm thick, 2nd class hard wood , glazed & skeleton factory made shutters ( ISI Marked) , open rebated & prepared to receive glass, gauze etc. (without sash-bars), edges of framing plain, chamfered or rounded fitted with cut and metred beads for securing glass etc., sizes of members of shutters as specified in SSR Part-I, Section-8, clause 8.20(a) complete all as specified.Note:- Before procurement of door the contractor has to produce the sample of door(factory made) for approval and refernce

Providing and fixing windows & ventilators fabricated from Rolled Formed GI Section made of Galvanised steel colour coated(PPGI Sheets) (Base steel as per IS 513 ‘’D’’ quality. Galvanised as per IS 277 with Zinc of 90 Gsm/SqMt w. PAINT: Pre-Painted sections should be with primer coat of epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer of 5-7 microns or powder coated with pure polyester powder upto 50-60 microns thick.GI Section of 0.58mm thick in Double rebate windows in which both glazed shutter and flymesh shutter, 74 X 60mm outer frame , Mullion 72 x 49mm, Glazed shutter 48 x 22mm, Flymesh 41 x 22mm, Beading with round ends for Glass Fixing 12 x 12mm in fixed portion and the outer frame and mullions to have rebate for glazed/gauzed shutters the sections cut to length metre joined with corner PolyVinylChloride brackets centre mullion fixed with PolyVinylChloride Mullion caps . Glass of 4mm thick plain float glass fitted with Ethylene Propylene Diamine Monomer in glazed shutter and wiremesh of Stainless steel of 36 guage to fix mesh in mesh shutter using VC Black Gypsum Drywall screws and Spoon profile of 0.58mm GI Sheet. Corners of the windows should be joined with corner brackets made of polyvinylchloride with crca of zinc phosphate coat.Each glazed shutter and fly mesh shutter shall be provided with SS Pivot Hinges 2 in each, PolyVinylChloride handle 1 in each and Powder coated Peg stay in Glass shutter.Window shall be provided with Powder coated MS Grill/Guard Bars made of 10mm MS Sq Bar welded to 6 x 12mm MS Flat with countersunk holes at both vertical ends . Gap between the bars should not be more than 150mm . Window frames shall be fixed to brick / concrete masonry by using nylon self expension caps & 75/100 mm MS screws after drilling in walls. VC Black Gypsum Drywall screws should be used while fixng corner brackets,stay,hinges,mullion caps of windows. . Windows to be procured from any of the below mentioned companies- i)_Ashwani and sons, 1246/2 Meerut Road,Morta, Murad nagar-201003 ii)TATA Steel-Mumbai iii)Jindal,2-32,Gurgaon, Haryana-122001 iv) Ashish Industries, R-4/66, Raj Nagar, Ghaziabad , Ph-9891542779

S & F Butt hinges, 100 mm long stainless steel non magnetic ( ISI marked ) complete all as specified and directed..

S & F Butt hinges, 75 mm long stainless steel non magnetic (ISI marked) complete all as specified and directed..

S&F 300mm long aluminium alloy anodised sliding door bolt with hasp staple, bolt type, and fixing clips of sheet, cast or extruded sections & fixing bolts and sliding bolts of extruded section or cast aluminium alloy, ISI marked complete all as specified and directed.

S&F 250mm long aluminium alloy anodised sliding door bolt with hasp staple, bolt type, and fixing clips of sheet, cast or extruded sections & fixing bolts and sliding bolts of extruded section or cast aluminium alloy, ISI marked complete all as specified.

S&F 200mm long, aluminium anodised, barrel tower bolts, of extruded section ISI marked complete all as specified and directed.

All as per Srl Item No 62 here in before but 150 mm length of bolt.complete all as specified and directed.

S & F Aluminium handles cast type anodised of size 150mm long ISI marked complete all as specified and directed.

S & F Aluminium handles cast type anodised of size 125 mm long ISI marked complete all as specified and directed.

S & F 300 mm size mild steel ordinary rat tail rod pattern springs including roller and roller plate, ISI marked complete all as specified and directed.

S & F Stainless steel wire cloth non magnetic 0.56 mm nominal dia of wire and avarage width of aperature 1.18 mm dia complete all as specified and directed

Supply & Fixing mild steel flat iron as in hold fast,wind ties over roof covering using steel of grade Fe-310-O or Fe-410-O including necessary drilling holes etc and similar works complete all as specified and directed.

M&L as in Mild steel framed work as in grills, grating etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bars, conforming to Fe-410-0 or Fe-310-0,complete all as specified and directed.

Dismantling of water tanks exc 250 ltr capcity but n exc 500 ltr and removing to store. complete all as specified and directed.

Dismantling of water tanks exc 500 ltr capcity but n exc 1000 ltr and removing to store. complete all as specified and directed.

S&F Rotational moulded polyethylene water storage tank (ISI Marked only) including, plastic lid cover ( ISI Marked) , Double layered, cylindrical vertical with closed top hoisted and fixed in position of capacity 500 ltrs including making connections,20 mm dia ball valves( ISI Marked heavy duty ) high pressure PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe anf fixed complete all as specified and directed.

S&F 1000ltr capacity rotational moulded polyethylene water storage tanks (ISI Marked only) including, plastic lid cover ( ISI Marked) , double layered, (cylindrical vertical with closed top) hoisted and fixed in position and including 20 mm dia ball valves ( ISI Marked heavy duty ) high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed complete all as specified and directed

S&Fixing as in repair Stop valve 20mm dia bore (ISI Marked only) ,cast copper alloy, screwed down, high pressure, with crutch or butterfly handle,screwed both ends for iron pipe or for unions and fixed.complete all as specified and directed.

S & F in repairs vitreous china squatting pan 'orissa pattern 580 mm X 440 mm white (ISI Marked only) with integral foot rests (excluding flushing cistern and flushing pipe but inclding fixing of flushing cistern flush pipe etc complete) complete all as specified and directed.

S & F CI Nahani trap 75 mm dia with grating (ISI Marked only) including jointing to waste pipe fixed in cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) complete all as specified and directed

S&F in repair vitreous china wash down water closet pan (pedestal pattern EWC) (ISI Marked only) , white (excluding , flushing cistern and flush pipe) but including sheet cover and fixing of flush pipe complete all as specified and directed.

S & F in repairs stainless steel kitchen sink 1.00 mm thick (ISI Marked only) for kitchen with plugs, washer and waste 32/40mm dia incl bedding in cement mortar on to dwarf wall or including fixing cantilever cast iron brackets and connecting union to waste pipe overall all size 495mmx420mm bowl size 410x330x160mm complete all as specified directed.

S & F in repairs PVC Valve less, syphonic action type, Dual type flushing cistern (ISI Marked only), 10 litres capacity with inlet, ball valve float and handle with and including brackets & PVC bend pipe 60/90 cm long etc, supplied and fixed, complete all as specified.

S&F Vitreous china wash hand basin ,white ,flat back of size 550x400mm (ISI Marked only) with PVC connection 15mmdia 450 mm long with PTMT (ISI Marked only) nuts and PVC washer and including cutting for pinning in ends,pair of cast iron brackets and provision of PVC waste pipe 32mm of adequate length , waste coupling 32 mm dia of PTMT half or full threaded Min wt 45 gram,complete all as specified and directed by Engr-in-charge.

Supply only flush pipe of polythene of low or high density 32 mm PVC for low level flushing cistern (ISI Marked only) complete all as specified.

Supply only low density PVC pipe 32/40 mm dia as in waste pipe to sink (ISI Marked only) complete all as specified and directed

S&F in repair 20 mm dia bras chromium palted tubler towel rail D type 60 cm long between flange including one pair of fixing brackets complete all as specified and directed ( complete all as specified and directed.

S&F PVC connection 15 mm size, of length 450 mm (ISI Marked only), with PTMT nuts supplied and fixed in repairs complete all as specified and directed..

Cutting chases,pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps cills, sunshades, shelves,lintels etc; and cutting chases for concealed water tubing and making good, cutting not exc. 10cm girth.complete all as specified and directed.

Taking up or down steel tubing with connections for cleaning for refixing or removing to storeyard complete of bore 15mm.complete all as specified and directed.

Taking up or down steel tubing with connections for cleaning for refixing or removing to storeyard complete of bore 20mm. complete all as specified and directed.

S& F GI tubing 15mm bore, medium grade ISI marked with all fittings(such as bends, elbows, Tee short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions, including short lengths etc.) ( heavy grade ISI Marked) , fixed to walls, concealed in wall and ceiling or laid in floor complete complete all as specified and directed.

S& F GI tubing 20 mm bore, medium grade ISI marked with all fittings(such as bends, elbows, Tee short pieces, connectors, back nuts, diminishing pieces, caps and plugs,unions etc.) ( heavy grade ISI Marked) including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete . complete all as specified and directed.

S&F in repair 15 mm dia CP brass center (pillar tap) with accessories in was basin for mixing hot and cold water , screwed down for 15 mm dia bore GI pipe complete all as specified and directed ( Note- Chromium plated fitting shall be brought in store yard first as approved by GE/AGE(I) and will be issued subsequently for fixing at site .

S&F in repair bib tap cast copper alloy with crutch or butter fly handle, screwed down for iron pipe 15 mm bore of tubing fancy type cromium plated (ISI Marked). complete all as specified and directed.( Note- Chromium plated fitting shall be brought in store yard first as approved by GE/AGE(I) and will be issued subsequently for fixing at site .

S&F in repair Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure with long screwed shanks and fly-nuts, screwed for iron pipe screwed down for 15 mm dia bore GI pipe complete all as specified and directed ( Note- Chromium plated fitting shall be brought in store yard first as approved by GE/AGE(I) and will be issued subsequently for fixing at site .

S&F in repair chromium plated health fauset telephonic type with CP flexible arms of approved make suitable for 15 mm bore iron pipes or for union and fixed complete all as specified and directed complete all as specified and directed Note- Chromium plated fitting shall be brought in store yard first as approved by GE/AGE(I) and will be issued subsequently for fixing at site .

S & F in repairs Cabinet mirror of minium size 558.8x343x114.3 mm size Make –Pearl Cat Part No.MCB-251 or equivalent in Hindware ,Pryag/ Rajshree complete all as specified and directed.

S&F in repair CP shower rose with or without swivel joints of 125 mm size fancy type with shower arm complete all as specified and directed Make of shower rose Note- Chromium plated fitting shall be brought in store yard first as approved by GE/AGE(I) and will be issued subsequently for fixing at site .

S&F in repair stop valve cast copper alloy screwed down high presure screwed both end for iron pipe 15 mm dia fancy type cromium plated (ISI Marked). complete all as specified and directed. Note- Chromium plated fitting shall be brought in store yard first as approved by GE/AGE(I) and will be issued subsequently for fixing at site .

S&F in repair soap dish brass chromimum plated screw 125mm size complete all as spcified and directed Note- Chromium plated fitting shall be brought in store yard first as approved by GE/AGE(I) and will be issued subsequently for fixing at site .

S & F for Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long fixed in repair Make - Pryag, Hindware, Jaquar Essco complete all as specified and directed

S&F Curtain rod 25 mmm dia of Stainless steel non magnetic, medium grade fixed with SS brackets brass chromium plated including bracket. complete all as specified and directed. Note- Chromium plated fitting shall be brought in store yard first as approved by GE/AGE(I) and will be issued subsequently for fixing at site .

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified.

S&F Pre-painted galvalume aluminium zinc coating AZ-150 GI based corrugated steel sheet 0.50mm thick of any colour (ISI Marked) having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating AZ-150 GI based plain steel sheet 0.50mm thick (ISI Marked) of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

M & L for 0.63mm thick galvanized corrugated or semi-corrugated steel sheeting with two corrugations side lap (ISI Marked) , fixed with coach screws and washers, in roofs, walls etc with grade of zinc coating in roofing or fixed with new J-hooks/L-hooks/cranked hook bolts etc complete all as specified. The sheets shall be conforming to IS.complete all as specified and directed.

All as per item 104 above but except sheets.complete all as specified and directed. Note :- Old servicable corrugated steel sheeting, any gauge, thickness as obtained from item No. 101 shall be reused in this item.

M & L for 0.63 mm thick plain Galvanised mild steel sheeting (ISI Marked) , in ridges, hips, fascia boarding, valley gutters, drip and straight flashings (length and girth as fixed with grade of zinc coating fixed with new J-hooks/L-hooks/cranked hook bolts or fixed with coach screws and washers, in roofs, walls etc complete all as specified. The sheets shall be conforming to IS .complete all as specified and directed.

M&L for mild steel angle iron as in framed chowkats for door shutters cut to length including necessary welding and making holes for fixing butt hinges and fixing 10 mm dia as tle bar complete confirming to Fe-410 -O etc all complete all as specified and directed.

M&L for 40mm thick PCC (1:2:4) type B-1 using 20 mm graded stone aggregate as in flooring including finishing the top surface even & smooth, without using extra cement complete all as specified and directed.

M&L for 75mm thick PCC (1:3:6) type C-2 using 40mm graded stone aggregate as in plinth protection and similar works including finishing the surface of concrete topping even & fair, without using extra cement complete all as specified and directed.

Supply only glass dividing strips 38 mm wide and 3 mm thick inserted in position as approved pattern by EIC complete all as specified and directed.

Preparation of newly plastered surfaces of walls and applying three coats of white wash complete all as specified and directed.

All as per Srl Item No. 111 here-in-before, but on ceiling complete all as specified and directed.

M&L for preparation of newly plastered surface of internal wall by application of wall care putty to remove the dent and to make the surface even and smooth by grinding or rubbing with sand paper and applying two coats of acrylic distemper over a coat of primer using roller all as specified and prescribed by manufacture of paint and as directed at site by Engineer-in-Charge. Note:- (i) The new surface must be prepared in a manner so that there should not be any impression of dent and it should be made even and smooth all as per manufacture’s instruction before application of distemper The cost of all material T&P and labour required for preparation of surface are deemed to be included in the rates quoted . (ii). The work must be got executed through authorised applicator of manufacture after concluding an MoU with manufacture for company back guarantee by the contractor. The authorised applicator of manufacturer shall be got approved from GE/ AGE (I) before commencement of work. (iii). All the material to be incorporated in the work shall be brought by contractor to MES store yard which will be subsequently issued by deportment for incorporation in the work to ensure the quantity to be consumed all as per recommendation of manufacture. (iv). After carrying out preparation of surface the same shall be got approved from GE /AGE (I) before application of distemper for each building. (v). The colour / shade will be all as approved by GE / AGE (I)

M&L for preparation of newly plastered surface of external wall all as prescribed by manufacture of paint and applying two coats of exterior anti fungal acrylic emulsion paint (walmista of Berger paint or equitant in Asian paint, Nerolac etc having three years of performance warranty) over a coat of exterior water based primer of same make all as specified and prescribed by manufacture of paint and as directed at site by Engineer-in-Charge. Note:- 1. The newly plastered surface must be prepared in a manner so that there should not be any impression of dent and it should be made even all as per manufacture instruction before application of emulsion paint. The cost of all materials, T&P and labour required for preparation of surface are deemed to be included in the rates quoted. (ii). The work must be got executed through authorised applicator of manufacture after concluding an MoU with manufacture for company back guarantee by the contractor. The authorised applicator of manufacturer shall be got approved from GE/ AGE (I) before commencement of work. (iii). All the material to be incorporated in the work shall be brought by contractor to MES store yard which will be subsequently issued by deportment for incorporation in the work to ensure the quantity to be consumed all as per recommendation of manufacture. (iv). after carrying out preparation of surface the same shall be got approved from GE /AGE (I) before application of distemper for each building. (v). The colour / shade will be all as approved by GE / AGE (I) (vi) The cost of Scaffolding wherever required are deemed to be included in the rates quoted by the contractor

M&L for preparation of old decorated surface of internal wall by removing existing treatment with mechanical sander (rpm 1500-2700) along with internal dust extraction system for clean environment certified by reputed paint manufacturers and applying two coats of acrylic distemper using roller all as specified and prescribed by manufacturer of paint and all as directed at site by Engr-in-Charge . Note: (i) The old surface must be prepared in a manner so that there should not be any impression of dent and it should be made even and smooth all as per manufacture’s instruction before application of distemper. The cost of materials, labour & T&P required for preparation of surface are deemed to be included in the rates quoted. (ii). The work must be got executed through authorised applicator of manufacture after concluding an MoU with manufacture for company back guarantee by the contractor. The authorised applicator of manufacturer shall be got approved from GE/ AGE (I) before commencement of work. (iii). All the material to be incorporated in the work shall be brought by contractor to MES store yard which will be subsequently issued by deportment for incorporation in the work to ensure the quantity to be consumed all as per recommendation of manufacture. (iv). After carrying out preparation of surface the same shall be got approved from GE /AGE (I) before application of distemper for each building. (v). The colour / shade will be all as approved by GE / AGE (I)

M&L for preparation of old decorated surface of exterior wall by removing existing treatment with mechanical sander (rpm 1500-2700) along with internal dust extraction system for clean environment certified by reputed paint manufacturers, then washing the surface with Bleaching powder solution for treatment of fungal growth and applying two coats of exterior anti fungal acrylic emulsion paint (wallmista of Berger paint or equitant in Asian paint, Nerolac etc having three years of performance warranty) over a coat of exterior water based primer of same make all as specified and prescribed by manufacture of point and as directed at site by Engineer-in-Charge. Note: (i) The old surface must be prepared in a manner so that there should not be any impression of dent and it should be made even all as per manufacture instruction before application of distemper. The cost of materials, labour & T&P required for preparation of surface are demand to be included in the rates quoted. (ii). The work must be got executed through authorised applicator of manufacture after concluding an MoU with manufacture for company back guarantee by the contractor. The authorised applicator of manufacturer shall be got approved from GE/ AGE (I) before commencement of work. (iii). All the material to be incorporated in the work shall be brought by contractor to MES store yard which will be subsequently issued by deportment for incorporation in the work to ensure the quantity to be consumed all as per recommendation of manufacture. (iv). after carrying out preparation of surface the same shall be got approved from GE /AGE (I) before application of distemper for each building. (v). The colour / shade will be all as approved by AGE (I) (vi) The cost of Scaffolding wherever required are deemed to be included in the rates quoted by the contractor

M&L Painting to new wood or wood based surfaces of any description not otherwise described over 10 cm in width or girth including preparation of surfaces, priming with pink primer (one coat) finished with two coats of synthetic enamel paint complete all as specified.

M&L for Preparation of old wooden surfaces of any description over 10 cm width or girth & applying two coats of synthetic enamel paint Ist quality after removal of existing treatment from old surface with help of thiner or other removing chemical materilas complete all as specified and directed.

M&L Preparation of new zinc or galvanised surface to receive painting,by coating with modrant solution including washing ,cleaning etc and applying two coats of synthetic enamel paint complete all as specified and directed.

M & L for preparation of old steel surafces of any description over 10 cm width or girth & applying two caots of synthetic enamel paint Ist quality after removal of old existing treatments with help of thiner or other removing chemical materilas complete all as specified and directed

M&L preparation of new steel surface exc 10cm width or girth and applying two coats of synthetic enamel paints ( Ist quality) over one coat of red oxide primer complete all as specified and directed.

M&L for pre- polished granite slab machine cut of any shade as approved by AGE(I) of 16 to 18 mm thick including necessary notching, chamfering the edges over cement screed bed including Cutting, Grinding and Mirror polishing(Granite finish) with suitable grinding stones complete all as specified and directed. Note:- Edge of stone shall be bull nosed

S&F as in repair stainless steel kitchen plate rack of size 24x36x10 inch of minimum thickness 0.8mm including necessary drilling, fixing with screw, plugs in kitchen etc complete all as specified and directed

Demolition and breaking up drain pipe (SGSW )) of 150 mm nominal bore laid in trenches, set & jointed in cement morter, incl necessary earth work, all as specified and directed by the Engr-in-Charge.

M&L for Salt-glazed stone ware drain pipes laid in trenches and jointed as specified of 150 mm internal dia of pipe( ISI Marked only) .complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 using 40 mm graded crushed stone aggrs as in packing under and haunching against the sides of pipe or as required at site after the pipes are laid over the existing bed and tested for 150 mm bore of pipe all as specified and as directed by the Engr-in-Charge.

S & F for FRP door frame : fibre glass reinforced plastic (FRP) Door frames shall be three lagged of cross section 90mm x 45mm having single rebate of 32mm x 15mm to receive shutter of 30mm thickness. The laminate door frame moulded with fire retardant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fibre glass from all sides. MS stay shall be provided at the bottom to steady the frame. Complete all as specified and directed. Make - M/s Ashwini and Sons Murad nagar, TATA FRP Doors Mumbai, AGEWS Ahemdabad Gujarat, Ashish Industries Ghaziabad

S & F for FRP paneled door shutter FDR Door shutter shall be 30mm thick glass fibre reinforced plastic (FRP) panelled door shutter of required colour and approved brand and manufacturer. Made with fire retardant grade unsaturated polyester resin moulded to 3mm thick FRP laminat for forming hollow rails and styles with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5mm thick FRP panels. complete all as specified and directed : Make - M/s Ashwini and Sons Murad nagar, TATA FRP Doors Mumbai, AGEWS Ahemdabad Gujarat, Ashish Industries Ghaziabad

Dismantling of wall and ceiling board (fibre,insulation etc) or insulation board ,slabs,blankets, any thickness incl cover fillets complete all as specified and directed.

M&L for providing and fixiing designer E-boards, ceiling, 4 mm thick with J framed work with main Tee of size 24 x 28.5 mm made out of PGI sheet .3 mm thick double at web and single at flange, flange coverd with powder coated sheet 0.25 mm thick and wall angle 24 x 24 x .45 mm powder coated for ceiling , ceiling boards 60cm x 60cm x 4mm thick , suspended with GI wire 2mm dia and 2m average length with adjustable hanging device complete including plugging in brick/stone walls with steel rawl plug @ 600 mm C/C Ceiling board shall be pressed to the ceiling tee with staple clips at all four sides and painted inclding making good all the disturbed portion with finish complete all as Specified & directed by GE/Eng-in-Charge.

Dismantling boarding, any description, fixed in any position with nails complete all as specified and directed.

M & L for 2nd class soft wood boarding 20 mm thick planed one side and edges tounged & grooved or rebeted or screw fixed to timber frame work with screws complete all as specified and directed. .

All as per item 132 above but expect boarding. complete all as specified and directed. .Note:- Old Servicable boarding as obtained from item No. 131 shall be reused in this item.

Hacking out old broken glass (any thickness, size, quality or description) from metal frames including punching or drilling out old glazing pins/spring clips and providing and fixing new ones glazed with oil putty fixed with beads or in wooden shutters complete all as specified and as directed.

S&F for 4 mm thick sheet glass, ordinary quality and glazing with oil putty/wooden beads in square not exceeding 0.5 square metre in each pane complete all as specified.

All as per Item 135 Above but exc 0.5 Sqm in each pane complete all as specified and directed.

S&F for 4 mm thick figured (frosted) glass, ordinary quality and glazing with oil putty/wooden beads in square not exceeding 0.5 square metre in each pane complete all as specified and directed.

M&L for chequered cement concrete tiles 300X300X25 mm thick, rubber finished ,as in floors laid over 20 mm thick screed bed in cement mortar 1:6 jointed with grey cement slurry mixed with pigment to match the shade of the tiles including dismantling of old stone slab tiling/ tileing and including removalof old materials from site not exceeding 100 meter complete complete all as specified and directed

Dismantling post or strut embeded in concrete( wood/steel/RCC) any section embeded in concrete including taking out embeded portion and making good all as directed & specified

Dismantling fencing wire mesh of any description complete all as specified and directed

M&L for providing cement concrete type D-2 1:4:8 (40mm graded aggregate) in foundations, filling, post hole filling and mass concrete complete all as specified and directed.

S&F MS as in Hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed

Supply only galvanised chain link fencing of any dia and any mess size as directed by Engr-in-Charge complete all as specified and directed.

Fixing only chain link fencing including line wires any mesh, size and type to any type of standards, rails, straining bolts etc including provision of binding wire complete all as specified and directed

S & F 18 mm thick pre-laminated particle board, interior grade prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work as in Cup Board shutters complete all as specified and directed.

All as per itme above but 12 mm thick and pre-laminated both sides with decorative choice laminations as in Cup Board partitions complete all as specified and directed.

S & F 75 mm ,hasp & staple safety type aluminium with mild steel hing pin including bolt to hinge plate and fixed with screw complete all as specified and directed

S & F for steel work in tubular truss of square pipe hollow section including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade st-240.complete all as specified and directed.

S & F for Framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc., n exc 10 kg each brackets, conforming to Fe 410-0 or Fe 310-0 (Brackets over 10kg each to be measured under `Structural Steel') complete all as specified and directed.

S&F MS Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) with riveted, bolted or welded attachment confirming to Fe-410W (Gde E-250) quality B.complete all as specified and directed.

S&F in reapir door closer hydraulically regulated, designation No 2, universal type, aluminium (Die cast body) ISI Marked only sutable for door shutters complete all as specified and directed

S&F flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc, and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed

S & F Continuous (piano) hinges (width of flap 30 mm ),mild steel, bright finish or electrogalvanised (ISI Marked ) complete all as specified and directed.

S&F for PVC Panneling with PVC panels of 9mm thick and 250mm wide interlocked type incl angle or channels and necessary fitting as rawl plugs,screws,adhesive etc complete all as specified and directed.

M&L rubber moulded factory made machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness , M-35 grade (ISI Marked ), set, jointed and pointed in neat cement slurry in floors with grey cement & pigments including and over 50 mm thick sand cushioning for laying of inter locking tiles (paving blocks) including dismantling of old stone slab tiling/ tileing and including removal of old materials from site out of A 1 defence land complete all as specified and directed (Note : Design/shade of rubber moulded machine presses precast concrete Paver block shall be as approved by GE/Engr-In-Charge.)

M&L Providing for cement concrete type (1:3:6) C-1 using 20mm graded stone agg as in copings, kneelers complete all as specified and directed.

M&L Providing for cement concrete type (1:3:6) C-1 using 20mm graded stone agg as in bonders (for stone walling) and setting the block slab etc in cement mortar 1:6 complete all as specified and directed.

M&L for hand packing (any thickness) at back of walls over arches etc as back filling in retaining walls, and rainsing and lowering to the required with brocken stone or boulders complete all as specified and directed.

M&L for raised pointing to random rubble or polygonal rubble masonry uncoursed or brought upto course in cement mortar 1:4 complete all as specified and directed.

Extra over stone walling for hammer dressing to faces of stone and dressing of faced beds and joints as specified for random rubble masonry uncoursed or brought upto coursed against dressed surface not exc 40mm complete all as specified and directed.

M & L for PCC type C1 (1:3:6) (using 40mm graded stone agg ) as in surface channel or drain or benching in manhole complete incl. necessary form work all as specified and directed.

M & L for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement including forms, moulds, mitered / stopped ends etc. complete all as specified and directed.

S&F 2nd class hard wood (Sal) fillets square or rectangular or triangular in section wrought fixed to wall with screw area exc 13 but not exceeding 25 sqcm. complete all as specified and directed.

S&F in repair 15 mm dia CP brass ( Brass chromium plated Wall mixer ) with accessories for mixing hot and cold water , screwed down for 15 mm dia bore GI pipe complete all as specified and directed Note- Chromium plated fitting shall be brought in store yard first as approved by GE/AGE(I) and will be issued subsequently for fixing at site .

S&F factory made 100% Solid wood Plastic composite (WPC) door frame 75X50 mm made from wood plastic composite (single extruded Process) materials with density 780Kg/Cum from ISO certified company door should be weater proof , termite proof, fire retardant and having good screw holding capacity all as per specification and drawing as directed by Engineer-in-charge Make: Enhon/ Sintex/Rajshree

S&F 30 mm thick moulded WPC Factory made 100% solid door ( Conforming as per IS -4020) made from 100% lead fire single extruded with 2,4 or 6 raised Panel design on the front side with 10 mm deep mould on single side with wood grain texture and back side Plain with density not less than 600 Kg/cum . Manufactured by an ISO :9001-2015 certified Company. The door should be water proof , termite proof, termite proof , fire retardant and having screw holding capacity . complete all as specified and directed.Make: Enhon/ Sintex/Rajshree

Taking down carefully copper/aluminum point wiring (light/fan/socket power) complete , including fixture and fitting such as switches, ceilling roses, pendants, regulators, sockets, light fittings etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per condition seperately) and making good disturbed surfases of walls, floors, etc. all as specified and directed.

M&L Point wiring with 1.5 Sqmm (Nominal area) FRLSH PVC insulated and unsheathed single core cable 1100 volts grade with stranded copper conductor in and including concealed rigid PVC conduit(ISI marked) medium grade of size not less than 20 mm dia including accessories incl cutting chases etc along with contineous earth wire 1.5 Sqmm FRLSH PVC insulated , unsheathed stranded copper conductor cable and connected to common earth dolly, with and including 1.6mm cadmium plated sunk MS pressed steel terminal boxes with 3.0 mm thick hylum sheet cover ISI marked fixed wth brass screw complete with all accessories for Make of PVC pipe:-Finolex,RPG,ESS ESS Kay

(a) one light point/fan point/call bell point controlled by one, oneway switch.

One 3 pin 5 Amps socket outlet on same board controlled by one, one way 5 Amps piano switch.

One socket outlet 5/3 pin 5 Amps controlled by one switch on independent board.

M&L Point wiring with 2.5 Sqmm (Nominal area) FRLSH PVC insulated and unsheathed single core cable 1100 volts grade with stranded copper conductor in and including concealed rigid PVC conduit(ISI marked) medium grade of size not less than 20 mm dia including accessories incl cutting chases etc along with contineous earth wire 2.5Sqmm FRLSH PVC insulated , unsheathed stranded copper conductor cable and connected to common earth dolly, with and including 1.6mm cadmium plated sunk MS pressed steel terminal boxes with 3.0 mm thick hylum sheet cover ISI marked fixed wth brass screw complete with all accessories for Make of PVC pipe:-Finolex,RPG,ESS ESS Kay (a) one three pin 15 Amps Switch Socket outlet on independent board

S&F switch piano 230 volts AC flush type, single pole, one way 6 Amps ISI Marked complete all as specified and directed. Make : Anchor/ Cona / Havells

S&F switch piano 230 volts AC flush type single pole, one way 16 Amps ISI Marked complete all as specified and directed. Make : Anchor/ Cona / Havells

S&F socket outlet 2/ 3 pin 230 volts 5/6 Amps flush type complete all as specified and directed. Make : Anchor/ Cona / Havells

S&F socket outlet 3 pin 5 amp & 3 pin 15 Amps flush type 230V AC (ISI Marked) complete all as specified and directed. Make : Anchor/ Cona / Havells

S&F bell push piano flush single pole one way 5/6 Amp (ISI Marked) complete all as specified and directed. Make : Anchor/ Cona / Havells

S&F bell ding dong elelctric 230V AC single pole all as speccified and directed Make : Anchor cate part No doorbell-10489-1B or equavalent in Cona / Havells

Supply & fixing lamp holder (Angular/Straight ), insulated body, with back plate for batten fitting ISI marked complete all as specified & directed Make : Anchor/ Cona / Havellsdirected

S&F ceiling rose 3 terminal / PVC/ polycarbonate, isolated body ISI marked all as specified and directed Make : Anchor/ Cona / Havells

S&F MCB DB SPN 8 way with 200 amps 240 volts rated copper busbar in sheet steel enclosure.double door type complete all as specified and directed.

Supply & fixing MCB , SP, AC, 240 volts of 06 to 32 Amps capacity 10KA, 'B' series and making connections with suitable size of copper lugs complete all as specified & directed.

Supply & fixing MCB, SPN, AC, 240 volts of 40 Amps capacity 10KA, 'B' series and making connections with suitable size of copper lugs complete all as specified and directed.

Supply & fixing MCB, SPN, AC, 240 volts of 63 Amps capacity 10KA, 'B' series and making connections with suitable size of copper lugs complete all as specified and directed.

S&F LED tube light batten 20 Watt, 4ft, Polycarbonate housing, translucent diffuser, With LED Light Source, 2200 Lumens, natural White, Surge Protection range- 2KV, Voltage Protection range – 120 -280VAC, 2 years warranty , System efficacy not less than 110Lm/Watt for the fitting, power factor >0.95, total harmonic distortation<20%, Color rendering index >80, Coefficient Colour Temperature – 6500K, Fixed on site with all accessories all as specified & directed. Make Shakti Cat Part No: SZSLBMX020 or equivalent in Havells, Wipro or Bajaj LM79 and LM 80 Reports to be produced. BIS Certification must.

S&F Decorative ultra slim round profile LED Tube light fitiing with extruded polycarbonate, energy efficient for mirror light 9 Watt 2 ft with LED light source with uniform light output, fixed on site with all accessories all as specified & directed Make - Havells Cat Part No. LHEXBLP71N1W009 or equivalent of shakti /Wipro/ Bajaj/Shakti

S&F decorative wall mounting champagne gold finish fixture with plastic body complete incl fixing LED lamp including connecting up with twin core twisted flexible copper conductor cable with suitable size of 230V , 50 HZ complete all as specified and directed.. Make: Havells Model - STYLO cat part NO- LHFOECE1TZ10014 or equivalent of Bajaj / Shakti/ Wipro Note : LED bulb of suitable wattage shall be issued by department as "free for fixing" only

S&F Crown shaped Post top lantern fitting in soothing moon finish made up of polycarbonate, suitable up to 27 W retrofit LED lamp with B-22 base completer with lamp.complete all as specified and directed. Make - Havells Model No. ATHENA 3 (MOON) or equivalent of Bajaj/Wipro/Shakti.

Supply and fix LED building security light fitting 20W housing made out of pressure die-cast aluminium alloy with toughned glass, IP-66 protection, working on 240 Volts AC, 50 HZ, consisting of reflective lens wired with approximate driver PF>0.98 having over voltage protection upto 440 volts, Surge protection level > 10 KV, thermal short circuit protection THD < 10% made up of long life LED chips (SMD) in modular with Ra>70, and LED lumen efficiency >140 lumen per watt, beam angle along the drive way, 120 degree, beam angle across the drive way, 80 degree luminior efficiency > 120 Lumens/watt power LED should be of more than 01 watt CCT should be between 5700 K- 6500 K including fixed on pole with 02 Nos MS clamp made out of 40 x 6 mm F1 and bracket made out of 32 mm dia light grade GI pipe not less than 0.9 mtr long bend to shape including connecting with 1.5 sq mm, 3 core, PVC insulated Copper conductor cble 1100 Volta grade all as specified and as directed by Engr-in-Charge Make : shakti Cat Part No : SZPSLPM020/ ENDURAPEARLSL20W of HAVELLS or equivalant Model in Bajaj/Wipro (i) the firm has to give warranty for street light fittings including driver minimum for 03 years for any defects developed during the period. (ii) The contractor shall submit the third party LM 79 & LM 80 report from any NABL approved laboratory. (iii) The fitting should have BIS, CRS

S&F sub main wiring with two single core PVC insulated,unsheathed, stranded copper conductor cable 6 Sqmm with 46Sqmm PVC insulated, unsheathed, stranded copper conductor cable as earth wire in and including rigid PVC conduit 25mm dia or higher, medium grade ISI marked and earth wire connected to common earth dollycomplete all as specified and directed. . Make of Cable : Finolex/RR Cable/Havells & Make for Conduit : AKG / PRESTOPLAST / PRECISION ) Note: Three run of 6sqmm cable and one run of PVC conduit shall be measured as one unit

S&F sub main wiring with two single core PVC insulated,unsheathed, stranded copper conductor cable 4 Sqmm with 4.00 Sqmm PVC insulated, unsheathed, stranded copper conductor cable as earth wire in and including rigid PVC conduit 25mm dia or higher, medium grade ISI marked and earth wire connected to common earth dolly all as specified & directed Note: Three run of 4 sqmm cable, and one run of PVC conduit shall be measured as one unit

S&F Exhaust fan AC single phase 230/240 Volt of size 300 mm sweep, metallic body powder coated painted finish, Power consumption- 50 W, Air deplacement -1290 Cum/Hr, RPM-1350 complete with louvers including making whole and grouting of nut bolts etc and making good the disturbed sufaces of wall complete all as specified and directed. Make - Orient/Bajaj/Havells/Crompton

Supply, Laying and testing cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sq mm 2 core( ISI Marked only).complete all as specified and directed.

Supply, Laying and testing cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sq mm 2 core( ISI Marked ) .complete all as specified and directed.

Material & labour for earthing complete with galvanised steel earth plate electrode 600x600x6mm thick burried directly in ground. ( earth pit not less than 2.25 mtr depth below ground level at any type of strata ) with top edge of the earth plate not less than 1.5mtr below normal ground level connected by 4 mm GI wire as earth lead by means of brass nuts and bolt,thimbles check nuts, washers including concrete chamber of PCC 1:3:6 type C-1 using 20mm graded stone aggregate with fair finish, internal surface of concrete chamber shall be given internal dia 300mm x300mm, 15mm thick plaster in CM 1:4 funnel with wire mesh, RCC pit cover of 320x320x80mm size (1:2:4) Type B1 using 20mm graded stone aggregate rainforced with XPM and charcoal, dust and common salt all as shown in electrical plate No 3 of MES SSR Part-1(2009) and specified including and provision of GI wire upto 7.5 mtrs long with 15 mm dia light grade Gi pipe protection and watering pipe of GI 20 mm bore, medium grade, including all excavation and earth work and connecting the earthing strip to panel, including testing on completion complete all as specified and directed by Engr-in-charge. Note:- (i) RCC pit cover shall be precast of RCC(1:2:4) type B1, 80mm thick rainforced with XPM weighting not less than 4kg/sqm in lieu of CI cover.(ii) Cost of additional GI wire more than 7.5 mtrs will be measured and paid seperately under relevant items.

M&L for fine dry sand cushioning for under ground cable by providing layers of sand 8 cm deep before laying and 15cm deep after laying the cableincluding streching the cable complete all as specified and directed.Note :- Punned (consolidated) thickness of sand will be measured and paid.

M&L for cable protection bricks common burnt clay sub class 'B' designation 75 for protection of UG cable laid in trenches all as specified and directed at site.complete all as specified and directed.

Supplying, laying & jointing GI water tubing, 40 mm bore, light grade as in sleeving etc laid in trenches / pole post /under culvert/ under road etc. for cable protection complete all as specified and directed .

PIONEER REFRIGERATION AND ELECTRICALS

RAMAPATI ENGINEERING SERVICES

HIND CONSTRUCTIONS