Finishing works for new mechanical workshop building in Phosphoric acid plant of FACT Cochin Division, Ambalamedu, Kochi.

Amount

Dismantling CC/RCC works including separately removing & stacking available reinforcement & clearing away the debris as per directions within a distance of 150 m.

Collecting ,conveying and Disposal of building rubbish / debris / similar unserviceable, dismantled or waste materials by manual/ mechanical means, including loading, transporting, unloading to approved areas for filling, spreading in layers as per directions of Engineer-in-charge (20%deduction will be made if measured loose in lorries/from stack) - For an average lead of 2 KM

Dismantling and clearing away any thickness of rubble, brick, laterite in CM including disposal of debris as per directions within a distance of 150 m.

Providing and laying in position machine batched and machine mixed design mix M-20 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer in-charge. (Note:- Cement content considered in this item is @ 320 kg/cum)

Cement block masonry work in CM 1:6 using good quality, approved, cement blocks including charges for conveying, scaffolding charges etc. as per departmental instructions for super structure walls up to floor five level including cost of cement

Chipping & removing old cement plastered surface including racking out joints & clearing the surface for replastering & disposal of the debris as per directions within a distance of 150 m.

Cement plastering with CM 1:4,15 mm thick one coat floated hard and trowelled smooth at all levels.

Painting one coat of priming coat on plastered surface (interior/exterior) with approved quality cement primer after cleaning the surface including all cost of materials, labour etc.

Painting two coats with ready mixed plastic emulsion paint of approved quality and colour specified over the priming coat already done and paid separately after cleaning the surface well.

Dismantling and removing doors with or without ventilators including removal of shutters, hinges, holdfast and all other fittings and stacking materials as per deptl.instructions

Dismantling and removing windows/ventilators/shelves/cup boards/AC frames etc including removal of shutters, hinges, holdfasts and all other fittings and stacking materials as per deptl.instructions

Providing and laying with approved brand rectified Glazed Ceramic floor tiles of size 600x600 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in suitable colours laid cement based high polymer modified quick-set tile adhesive (Water based) conforming to IS: 15477, in average 3mm thickness. with adequate joint spacing of 3mm followed by grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge

Providing and fixing first quality ceramic glazed wall tiles conforming to IS :15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades of any size as approved by Engineer-in-Charge for dadoing to walls cement based high polymer modified quick-set tile adhesive (Water based) conforming to IS: 15477, in average 3mm thickness. i followed by grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge.

Supplying and fixing PVC floor trap (single or multy type) of approved brand 110 mm size with required provision of outlets and inlets as per manufacturers specifications, cutting and making good the walls and floors, etc. complete.

Supplying and fixing 125 mm (5 inch) Stainless steel floor gratings (two piece) to PVC trap as per instructions at site

Supplying and fixing approved quality white glazed vitreous china flat back lipped front urinal of size 430x380x230 mm or nearest size with 1No. 15mm PVC heavy type connection and 1 No.15mm CP regulating valve of superior make ,CP spreader with flush pipe fixing the urinal to wall with Stainless steel screws with plastic grips including cutting and making good the walls etc. complete as per deptl instructions.

Supplying conveying and fitting 550x400mm or nearest size wash hand basin of white glazed vitreous china approved quality with a pair of special alloy bolts for fixing the basin on walls with 1 No. 15 mm heavy type CP brass pillar tap of approved make 1no.heavy type 15mm PVC connection and 1No.15 mm CP regulating valve of superior make ,1No. 15 mm CP waste coupling,32 mm PVC waste pipe with cp learning nut 1No. etc. including cutting and making good the walls,etc. complete.

Supplying and fixing at all levels approved quality /brand European type vitreous china white glazed water closet pan with P/S trap and White/Black duro plastic seat and lid with CP brass hinges and CP rubber buffers, 10 litre capacity PVC low level flushing cisternof approved make with all fittings 1No.32mm CP brass flush bend, 1No:15mm superior PVC connection heavy type ,15mm CP regulating valve,cutting and making good the walls and floors including giving connection to sewer pipe with all necessary specials,etc. complete as per direction at site

Supplying Angle valve with wall flange of standard range (CERA, JOHNSON or equivalent)

Supplying Long body bib cock of standard range CERA/JOHNSON or equivalent type

Supplying to Civil store 100 mm CP brass shower rose with 15 mm / 20 mm inlet and of approved brand / manufacturer

Supplying and fixing 600 x 450 mm or nearest size bevelled edge mirror of approved quality superior make " with hard board or plastic sheet on the rear and fixing the same in position with necessary plugs & SS screws etc complete

Suppling and fixing 600 x20 mm or nearest Stainless steel heavy duty approved brand towel rod with brackets with necessary SS screws, pastic grips etc. complete

Supplying and fixing Health faucets of standard range approved by Engineer-in-Charge (CERA,JOHNSON or equivalent brand)

Supplying and fixing best quality SS soap dish including cost of screws, wooden plugs etc.

Supply and fixing stain less steel hanger unit having min 3 hooks

Supplying and fixing anodized Aluminium frame work of extruded sections and approved brand / manufacturer including mitering the joints, fixing the frame work with necessary screws, drilling holes in floors/walls, providing plugs for fixing screws, finishing the sides of packing between frame work and walls with plaster of Paris, cost of timber packing if necessary, Rubber lining for air tightness, providing corner cleats etc.complete as per standard practice for glazed Doors, Windows, Partitions, Ventilators etc.including hinges ,pivots, tower bolts, fixtures etc.complete (All Aluminum works including fittings measured in Kg)

Glazing the Aluminium frame work of windows with 3 mm or nearest thick plain glass panes and anodized Aluminium approved brand beadings, with EPDM / NEOPRINE weather seals, gaskets of EPDM or PVC etc and screws as per standard practice at all levels (Measurement for overall area of doors / windows / ventilators)

Glazing/Panelling the Aluminium frame work of doors/other areas with 5.50 mm glass and 4 mm thick hylam sheets (40% hylam sheet aproximate) and powder coated Aluminium approved brand beadings, with EPDM / NEOPRINE weather seals, gaskets of EPDM or PVC etc and screws as per standard practice at all levels (Measurement for overall area of doors/other area)

Supplying and fixing Concealed Stop cock ¾ inch "CERA/ JOHNSON/ PARRYWARE or equivalent type.

Providing and fixing PVC door of syntex or equivalant make with shutter frame made of extruded plastic section having dimension of 60 x 24 mm or nearest, paneling with single panel hollow plastic section of 20 mm thick with average wall thickness of 1 mm and outer frame of door made of extruded plastic section of 48 x 40 mm or nearest including providing and fixing all required fittings such as stainless steel butt hinges, PVC tower bolts, PVC handles etc.complete as per manufacturers specifications.

Supplying and fixing PVC pipes conforming to IS 4985 class III, 6 kg/sq.cm pressure for lines with all required specials such as plain bends, single junctions, elbows, crosses, unions, shoes, door bends, double junctions, vent cowls, etc. with or without door including cutting masonry or concrete floors, sunshades, etc and making the holes good after finishing the work. wherever necessary and jointing pipes with approved quality resin cement and fixing pipes with MS fixing clamps screwed on to wooden plugs embedded in masonry wherever required and painting the clamps with two coats of enamel paint over one coat primer. This includes testing of joints complete at all levels. for waste water lines:110mm or nearest outer diameter

Supplying and fixing PVC pipes conforming to IS 4985 class III, 6 kg/sq.cm pressure for lines with all required specials such as plain bends, single junctions, elbows, crosses, unions, shoes, door bends, double junctions, vent cowls, etc. with or without door including cutting masonry or concrete floors, sunshades, etc and making the holes good after finishing the work. wherever necessary and jointing pipes with approved quality resin cement and fixing pipes with MS fixing clamps screwed on to wooden plugs embedded in masonry wherever required and painting the clamps with two coats of enamel paint over one coat primer. This includes testing of joints complete at all levels. for waste water lines 75mm or nearest outer dia.

Supplying, laying and jointing with solvent cement, Rigid PVC pipes conforming to IS 4985 Class V (10 Kg/cm2 pressure rating) for water lines with all required concealed (brass embeded) PVC specials, such as Tees, bends, elbow, union, reducer etc. with clamps if any including necessary cutting and making good the walls, earth work if required etc.complete - 25 mm OD Pipe

Supply and fixing of RCC cylindrical septic tank with three chambers for 20 users (1000 litres) having wall thickness of 50mm or nearest, inner diameter 750mm, outer diameter 850mm, length 2500mm, one inlet and one outlet PVC pipe, two manholes with covers fitted with stainless steel handles including installing in position with all necessary pipes and fittings and making connection with the waste line inclusive of cost of all excavation, backfilling, material and labour complete.

Steel reinforcement for R.C.C. work including straightening,cutting, bending, placing in position and binding all complete above plinth level.Thermo Mechanically Treated bars of grade Fe-500D or more.

Relnforced cement concrete 1:1.5:3 (l cement : 1.5 coarse sand(zone-II1) : 3 graded stone aggregate 20 mm nominal size) work at all- levels, excluding cost of centering, shuttering, finishing and reinforcement & including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and Curabillty as per direction of Enqineer in-charge.

Centering and shuttering including strutting, propping etc. and removal of form for :Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Supply, fabrication and fixing of steel structures made with M.S. hollow tubular sections as per IS4923 of different sections with insert plates,legs etc. and blinding the hollow tubes with MS plates etc. at all heights with necessary welding ,scaffoldiing and painting with two coats of zinc chromate yellow metal primer and two coats of synthetic enamel paint with all labour and material charges etc. complete

K M BIJU (BID ID -3247081)

K.M.Joy (BID ID -3247931)