REPAIRS TO FLOORING, PLASTING, JOINERY AND OTHER B AND R IN MES OFFICE AND CIV MD ACCN AT DEFENCE LAB JODHPUR

Amount

Taking down cement or cement lime plaster, any description on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc and removal of rubbish off the premises and leaving the work clear of any plastering complete all as specified & directed by Engineer-in-charge.

M&L 15 mm thick , plaster in cement mortar (1:4) on stone masonry wall surfaces or surfaces other than fair faces of brick work or one side of lathing and finishing the surface even and smooth without using extra cement complete all as specified & directed by Engineer-in-charge.

M&L preparing new plastered surfaces of walls and applying two coats of acrylic weather coats exterior grade paint over a coat of primer complete all as specified & directed by Engineer-in-charge.

M&L preparing old decorated surfaces of stone walls by complete removal of existing treatment and applying two coats of acrylic weather coats exterior grade paint over a coat of primer complete all as specified & directed by Engineer-in-charge.

M&L 15 mm thick , plaster in cement mortar (1:6) on stone masonry wall surfaces or surfaces other than fair faces of brick work or one side of lathing and finishing the surface even and smooth without using extra cement complete all as specified & directed by Engineer-in-charge.

M&L preparing new plastered surface of wall and applying 2 to3 mm thick birla white wall care putty complete all as specified & directed by Engineer-in-Charge.

M&L two coats of oil bound distemper of approved tint over and including a coat of primer on newly plastered surface of walls complete all as specified & directed by Engineer-in-Charge.

M&L preparing old plastered surface of wall by removing complete removal of existing treatment and applying 2 to3 mm thick birla white wall care putty complete all as specified & directed by Engineer-in-Charge.

M&L two coats of oil bound distemper of approved tint over and including a coat of primer on putty finished wall surface complete all as specified & directed by Engineer-in-Charge.

S&F rolled mild steel sections like angle, channel, flat etc as inframed work such as grills,gratings,etc,with ends of bars shouldered and/or riveted,or forged into spikes, framed guard bars;barred iron doors;ladders ;framed balusters;walk ways; railings;framedwork of water tanks,hold fast,wall ties andsimilar work confirming toFe-290Gde E-165 complete all as specified & directed by Engineer-in-charge.

M&L preparation of new or previously untreated steel surfaces of any description over 10cm width or girth not otherwise described and apply two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified & directed by Engineer-in-charge.

M&L preparation of old steel surface of any description, over 10 cm width or girth, not otherwise described and applying one coat of synthetic enamel paint (ordinary tint) complete all as specified & directed by Engineer-in -charge.

Demolition floor hearth or wall tiling including cement mortar bedding and backing coat and removing unserviceable materials, debris and rubbish to a distance not exceeding 100m complete all as specified & directed by Engineer-in-charge.

S&F coloured glazed ceramic tiles size 350x250x7 / 450x350x7/ 450 x 300 x 7mm thick on vertical surface of wall over and including 10mm thick backing coat in CM 1:4 set and jointed in neat cement slurry and pointed in white cement / coloured cement to match the tiles complete all as specified & directed by Engineer-in-Charge

M&L plain cement concrete (1:4:8) type D-2 using 40 mm graded crushed stone aggregate as in foundation, filling and mass concrete all as specified & directed by Engineer-in-charge.

M&L 25mm thick PCC 1:2:4 type B-0 using 12.50 mm graded crushed stone aggregate as in base for screed etc, complete all as specified & directed by Engineer-in-charge.

M&L light shade, vitrified tiles, 10mm thick (minimum), (square/ rectangular polished, area of each tiles exceeding 0.36 Sqm (including 600mmx600mm size) but not exceeding 0.42 Sqm, in flooring set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles and over 15mm thick screed bedding in CM 1:4 complete all as directed by Engineer-in-charge.

M&L vitrified tiles of light shade, 10mm thick (minimum) (square/ rectangular) polished area of each tiles equal to or exceeding 0.36 Sqm but not exceeding 0.42 Sqm,cut to size as required in skirting/dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour tiles over and including 10 mm thick rendering with CM 1:4 complete all as specified and directed by Engineer-in-charge.

M&L 18 to 20mm thick granite stone slab (colour as approved by AGE(I)) table rubbed and polished as in flooring, cooking platform,window cill,pillers,steps etc including rounding to edge of granite slab as required pointing with white cement (1:2) using marble dust with admixture of pigment to match with colour of granite slab over 15mm thick screed bed/backing coat in CM (1:4) complete all as specified and directed by Engineer-in-charge.

M&L 18 to 20mm thick granite stone slab (colour as approved by AGE(I)) table rubbed and polished as inwall lining (veneering to wall) 12mm thick in cement mortar(1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with colour of granite slab complete all as specified and directed by Engineer-in-charge.

M&L out door heavy duty full body vitrified tiles of any shade 600x600x15mm thick fixed with spacers over 6mm thick high polymer modified grey cement based tiles adhesive and grouted with epoxy grout over 25 mm thick plain cement concete 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate complete all as specified and directed by Engineer-in-charge.

M&L 4.00 mm thick PVC tiles/sheets,laminated plain coloured,marble mosaaic or mottled finish,laid with approved rubber based adhesive in floors complete all as specified and directed by Engineer-in-charge.

Taking down chowkats or frames (without taking of shutters from the frames) area not exceeding 1.5 Sqm each complete all as specified & directed by Engineer-in-charge.

Taking down chowkats or frames (without taking of shutters from the frames) area exceeding 1.5 Sqm but not exceeding 4 Sqm each complete all as specified & directed by Engineer-in-charge.

Taking down shutters of any description area exceeding 1.0sqm but not exceeding 2.0 sqm each with fittings each complete all as specified & directed by Engineer-in-charge.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement complete all as specified & directed by Engineer-in-charge.

S&F, solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specifications & directed by Engineer-in-charge.

S&F, 100mm size, butt hinges,extruded aluminium alloy with galvanised mild steel hinge pin,anodised type B-21 including necessary welding if required complete all as specified & directed by Engineer-in-charge.

S&F 150 mm size aluminium anodised barrel tower bolts of extruded section complete all as specified & directed by Engineer-in-charge.

S&F 150 mm size aluminium handle, cast type, anodiesed complete all as specified & directed by Engineer-in-charge.

S&F Anodised aluminium (powder coated) frame for doors,windows, ventilators, partition wall etc with one or more rebated including jointing cleat for fixing etc complete all as specified and directed by Engineer-in-charge.

S&F anodised aluminium(powder coating of any colour) door shutters,aluminium section weight 1.00 to 1.8 kg/m including necessary jointing cleats,glazing clips,rubber neoprene packing,handles 2 Nos in each door,hinges,anodised aluminium snap beading screws etc complete all as specified & directed by Engineer-in-charge.(thickness of powder coating not less than 50 micron) (Note :- Floor door spring & sheet glass shall be measured and paid seperately).

S&F anodised aluminium(powder coating of any colour) window and ventilator shutters,fixed type without sash bar,aluminium section weighting 1.00 to1.80 kg/m including necessary jointing cleats,glazing clips,rubber packing,anodised aluminium snap beading,screws etc complete all as specified & directed by Engineer-in-charge.(thickness of powder coating not less than 50 micron) (Note :- Floor door spring & sheet glass shall be measured and paid seperately).

S&F anodised aluminium(powder coating of any colour) window and ventilator shutters,side hung type without sash bar,aluminium section weighting 1.00 to1.80 kg/m including necessary jointing cleats,glazing clips,rubber packing,anodised aluminium snap beading,screws etc anodised aluminium fittings hinges (type B-21) 100 mm long (02 Nos) tower bolt 100 mm long (02 Nos) and handle 100 mm long (01Nos) on each shutters, complete all as specified & directed by Engineer-in-charge.(thickness of powder coating not less than 50 micron) (Note :- Floor door spring & sheet glass shall be measured and paid seperately).

S&F Anodised aluminium grill (powder coating any colour) 6mm aluminium section having square gap of 50 mm with U clip (weight not less than 0.50Kg per sqm) complete all as specified and directed by Engineer-in-charge. (Deco grill or equivalent, thickness of powder coating not less than 50 micron)

S&F 12 mm thick prelaminated particle board/ MDF board exterior grade, prelaminated both side with decorative choice lamination fixed with screws to timber frame work/aluminium frame complete as specified and directed by Engineer-in-charge.

S&F 100 mm size 4 Levers, bress mortice Lock, vertical type complete all as specified & directed by Engineer-in-charge.

S&F140mm Floor door stopper of aluminium alloy body and tongue,anodised,with hard drawn steel spring,fixed in floor complete all as specified & directed by Engineer-in-charge.

S&F, Aluminium(Die cast)body Door closer hydraulically regulated,designation No3,universal type,suitable for shutters of 851 to 1000 mm in width and of weight between 61to 80 Kg complete all as specified & directed by Engineer-in-charge.

M&L Double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box,main body with stainless steel cover,governing pivot made of brass,other parts made of mild steel heavy duty and making good to floor to match with existing floor complete all as specified and directed by Engineer-in-charge.

S&F 4.80 mm thick frosted sheet glass, ordinary quality and glazing in squares area not exceeding 0.5 Sqm in each pane complete all as specified & directed by Engineer-in-charge.

S&F 4.80 mm thick sheet glass, ordinary quality and glazing in squares area exceeding 0.5 Sqm in each pane complete all as specified & directed by Engineer-in-charge.

S&F 5.50 mm thick tinted sheet glass, ordinary quality and glazing in squares area exceeding 0.5 Sqm in each pane complete all as specified & directed by Engineer-in-charge.

S&F Solar control film 50 micron reflective type (graveware sun control or equivalent) complete all as specified & directed by Engineer-in-charge.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 and fixed with stainless steel wire staples complete all as specified & directed by Engineer-in-charge.

S&F in repairs stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 and fixed with stainless steel wire staples complete all as specified & directed by Engineer-in-charge.

S&F stainless steel framed work for stairs (square,round hollow section of any type etc) including stringers treads,landing,balusters,handrails,cleats,brackets etc complete all as specified and directed by Engineer-in-charge.

Demolition and breaking up drain pipes (Salt glazed ware, AC,PVC or reinforced concrete) of 75mm/110mm bore set in cement mortar complete all as specified and directed by Engineer-in-charge.

S&F 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors as waste & vent pipes complete all as specified & directed by Engineer-in-charge.

S&F PVC (SWR) bends any radius 110 mm bore with access door complete all as specified & directed by Engineer-in-charge.

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors as waste & vent pipes complete all as specified & directed by Engineer-in-charge.

S&F PVC (SWR) bends any radius 75mm bore with access door complete all as specified & directed by Engineer-in-charge.

S&F PVC (SWR) multi floor trap with grating including jointing with solvent cement 75mm complete all as specified & directed by Engineer-in-charge.

M&L 125mm/110mm dia PVC (SWR) gully trap, setting & jointing with solvent cement complete all as specified & directed by Engineer-in-charge.

Taking up or down 15 mm bore steel tubing and connections including cleaning for refixing or removal to store complete all as specified and directed by Engineer-in-charge.

S&F 15 mm bore galvanised iron tubing ISI Marked 'Medium Grade' with all fittings laid in floors or fixed to wall complete all as specified and directed by Engineer-in-charge.

Fixing only 15 mm bore galvanised iron tubing ISI Marked 'Medium Grade' with all fittings laid in floors or fixed to wall complete all as specified and directed by Engineer-in-charge.

Taking up or down 20 mm bore steel tubing and connections including cleaning for refixing or removal to store complete all as specified and directed by Engineer-in-charge.

S&F 20mm bore galvanised iron tubing ISI Marked 'Medium Grade' with all fittings laid in floors or fixed to wall complete all as specified and directed by Engineer-in-charge.

Fixing only 20 mm bore galvanised iron tubing ISI Marked 'Medium Grade' with all fittings laid in floors or fixed to wall complete all as specified and directed by Engineer-in-charge.

S&F in repairs bib taps, cast copper alloy Chromium Plated, with crutch or butter fly handle, screwed down, screwed for 15 mm bore iron pipe or for brass ferrule complete all as specified & directed by Engineer-in-charge.

S&F 125mm size brass chromium plated shower rose with shower arm of suitable length & bend of 45 degree with flange complete all as specified & directed by Engineer-in-charge.

S&F Brass chromium plated Tubular towel rail 20mm dia,D type, 60 cm long between flanges, complete all as specified & directed by Engineer-in-charge.

S&F stop cock, fancy type,brass chromium plated, with long shank and cup (concealed type) cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, screwed both ends for 15 mm bore iron pipe or for union complete all as specified & directed by Engineer-in-charge.

S&F in repair vitreous china wash basin white, flat back of size 550 x 400 mm white including waste fittings, brass, chromium plated, coupling, waste pipe, brackets including cutting for and pinning in ends of brackets errect stand, fixing waste pipe complete all as specified & directed by Engineer-in-charge.

S&F PTMT Liquid soap container fixed with brass chromium plated screws (As per sample kept in AGE B/R office) complete all as specified & directed by Engineer-in-charge.

S&F in repairs vitreous china EWC (Excluding flushing cistern and flush pipe) complete all as specified & directed by Engineer-in-charge.

S&F in repairs CP brass water jet spray suitable for EWC complete all as specified & directed by Engineer-in-charge.

S&F, in repair, brass chromium plated angle valve for 15mm bore pipe complete all as specified & directed by Engineer-in-charge.

S&F, in repair, white/ black plastic water closet seat, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed by Engineer-in-charge.

S&F 15 mm bore brass chromium plated angular stop cock with wall flange(2in1), complete all as specified & directed by Engineer-in-charge.

S&F stainless steel toilet paper with cutting edge cover (As per sample kept in AGE B/R office) complete all as specified and directed by Engineer-in-chage.

S&F stainless steel soap dish of standard size (As per sample kept in AGE B/R office) fixed with chromium plated screws complete all as specified & directed by Engineer-in-charge.

S&F in repairs PVC valveless, syphonic action type, flushing cistern, 10 ltrs capacity, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified & directed by Engineer-in-charge.

S&F in repairs vitreous china urinal,Half stall type,white including cantilever brackets,flush pipe,waste coupling,waste pipe 40mm,spreader etc complete all as specified & directed by Engineer-in-charge.

Dismantling of old un-serviceable PVC/RCC water tank of 1000 ltrs capacity complete all as specified & directed by Engineer-in-charge.

S&F 1000 ltrs capacity rotational moulded polythene water storage tanks (ISI marked) (Cylinderically vertical with closed top) hoisted and fixed in postion all as specified in SSR Part-I including 20 mm bore PVC float valve complete all as specified and directed by Engineer-in-charge.

Tirupati electricals works and services

HOODA CONSTRUCTION COMPANY

SNEH CORPORATION

vinayandsons