Construction of 14 Court Building complex at Bhimavaram, West Godavari District (A.P) : Package IA -RCC structures , Civil finishing works with internal electrical works

Providing and laying in position cement concrete of

20 4.1 specified grade excluding the cost of centering and - - -

shuttering - All work up to plinth level :

Signature of Contractor Signature

Digitally signedofby

Items Ref. DESCRIPTION Rate (INR) Amount (INR)

Sl No. (DSR- Unit Quantity DSR-

DSR-2025 MR DSR-2023/2022 DSR-2025 NDSR Amount

1:3:6 (1 Cement : 3 coarse sand (zone-III) derived

21 4.1.6 from natural sources : 6 graded stone Cum 40.30 7,178.75 2,89,303.63 - -

aggregate 40 mm nominal size derived from natural

1:4:8 (1 Cement : 4 coarse sand (zone-III) derived

22 4.1.8 from natural sources : 8 graded stone aggregate 40 Cum 230.00 6,812.00 15,66,760.00 - -

mm nominal size derived from natural sources)

1:5:10 (1 Cement : 4 coarse sand (zone-III) derived

23 4.1.10 from natural sources : 8 graded stone aggregate 40 Cum 10.00 6,518.60 65,153.41 - -

mm nominal size derived from natural sources)

Providing and fixing up to floor five level precast

cement concrete string or lacing courses,

copings, bed plates, anchor blocks, plain

24 4.5 window sills, shelves, louvers, steps, stair - - -

cases, etc., including hoisting and setting in

position with cement mortar 1:3 (1 Cement : 3

coarse sand), cost of required

Centering complete.

1:1.5:3 (1 cement : 1.5 coarse sand(zone-III)

derived from natural sources : 3 graded stone

aggregate 20mm nominal size derived from

Making plinth protection 50mm thick of cement

concrete 1:3:6 (1 cement : 3 coarse sand (zone-III)

derived from natural sources : 6 graded stone

aggregate 20 mm nominal size derived from natural

sources) over 75mm thick bed of dry brick ballast

40 mm nominal size, well rammed and consolidated

and grouted with fine sand, including necessary

excavation, levelling & dressing & finishing the top

Total Carried over to summary 21,89,938.90 - -

Providing and laying in position ready mixed or site

batched design mix cement concrete for reinforced

cement concrete work; using coarse aggregate and

fine aggregate derived from natural sources,

Portland Pozzolana / Ordinary Portland /Portland

Slag cement, admixtures in recommended

proportions as per IS: 9103 to accelerate / retard

setting of concrete, to improve durability and

workability without impairing strength; including

27 pumping of concrete to site of laying, curing, - - -

carriage for all leads; but excluding the cost of

centering, shuttering, finishing and reinforcement

as per direction of the engineer-in-charge; for the

following grades of concrete.

Note: Extra cement up to 10% of the minimum

specified cement content in design mix shall be

payable separately. In case the cement content in

design mix is more than 110% of the specified

minimum cement content, the contractor shall have

28 5.33.1 All works upto plinth level - - -

Concrete of M30 grade with minimum cement

content of 350 kg /cum

30 5.33.2 All works above plinth level upto floor V level - - -

Concrete of M30 grade with minimum cement

content of 350 kg /cum

Extra for R.C.C./ B.M.C/ R.M.C. work above floor V

32 5.38 level for each four floors Cum 829.03 355.65 2,94,844.88 - -

or part thereof.

Centering and shuttering including strutting,

33 5.9 propping etc. and removal of - - -

Foundations, footings, bases of columns, etc. for

Walls (any thickness) including attached pilasters,

35 5.9.2 butteresses, plinth and Sqm 196.08 842.50 1,65,197.40 - -

string courses etc.

Lintels, beams, plinth beams, girders, bressumers

and cantilevers

37 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts. Sqm 8,325.42 961.30 80,03,226.25 - -

38 5.9.7 Stairs, (excluding landings) except spiral-staircases. Sqm 114.29 764.95 87,422.86 - -

Small lintels not exceeding 1.5 m clear span,

39 5.9.15 moulding as in cornices, Sqm 204.00 392.15 79,998.60 - -

window sills, string

40 5.9.19 Weather shed, chajjas, corbels etc., including edges Sqm 116.00 951.10 1,10,327.60 - -

Suspended floors, roofs, landings, balconies and

access platform.

Signature of Contractor Signature

Digitally signedofby

Items Ref. DESCRIPTION Rate (INR) Amount (INR)

Sl No. (DSR- Unit Quantity DSR-

DSR-2025 MR DSR-2023/2022 DSR-2025 NDSR Amount

Extra for additional height in centering,

shuttering where ever required with

42 5.11 adequate bracing, propping etc., including cost - - -

of de-shuttering and decentering at all levels,

over a height of 3.5 m, for every additional

height of 1 metre or part thereof (Plan area to

Suspended floors, roofs, landings, beams and

43 5.11.1 balconies (Plan area to be Sqm 3,713.40 384.30 14,27,059.62 - -

Reinforcement for R.C.C. work including

44 5.22 straightening, cutting, bending, - - -

placing in position and binding all complete upto

45 5.22.6 Thermo-Mechanically Treated bars. Kg 8,25,995.56 107.85 8,90,83,620.85 - -

Steel reinforcement for R.C.C. work including

46 5.22A straightening, cutting, bending, placing in position - - -

and binding all complete above plinth level.

Thermo-Mechanically Treated bars of grade Fe-

Providing and fixing of expansion joint system

related with floor location as per drawings and

direction of Engineer-In-Charge. The joints system

will be of extruded aluminum base members, self

aligning / self centering arrangement and support

plates etc. as per ASTM B221-02. The system shall

be such that it provides floor to floor /floor to wall

expansion control system for various vertical

localtion in load application areas that

accommodates multi directional seismic movement

without stress to it’s components.

System shall consist of metal profiles with an

universal aluminum base member designed to

48 5.44 accommodate various project conditions and finish - - -

floor treatments. The cover plate shall be designed

of width and thickness required to satisfy projects

movement and loading requirements and secured

to base members by utilizing manufacturer’s pre-

engineered self- centering arrangement that freely

rotates / moves in all directions. The Self - centering

arrangement shall exhibit circular sphere ends that

lock and slide inside the corresponding aluminum

extrusion cavity to allow freedom of movement and

flexure in all directions including vertical

Provision of Moisture Barrier Membrane in the

Joint System to have watertight joint is mandatory

49 requirement

5.44.3 floor Joint of all

the manufactures design and Rmt 170.00 9,903.65 16,83,620.50 - -

Providing and fixing of expansion joint system

related with wall joint (internal/external) location

as per drawings and direction of Engineer-In-

Charge. The joints shall be of extruded aluminum

base members, self aligning / centering

arrangement and support plates as per ASTM B221-

02. The material shall be such that it provides an

50 5.45 Expansion Joints System suitable for vertical wall to - - -

wall/ wall to corner application, both new and

existing construction in office Buildings &

complexes with no slipping down tendency

amongst the components of the Joint System. The

Joint System shall utilize light weight aluminum

profiles exhibiting minimal exposed aluminum

surfaces mechanically snap locking the multicellular

Signature of Contractor Signature

Digitally signedofby

Items Ref. DESCRIPTION Rate (INR) Amount (INR)

Sl No. (DSR- Unit Quantity DSR-

DSR-2025 MR DSR-2023/2022 DSR-2025 NDSR Amount

Providing and fixing of expansion joint system of

approved make and manufactures for various roof

locations as per approved drawings and direction of

Engineer-in-charge. the joints shall be of extruded

aluminum base members with, self aligning and self

centering arragement support plates as per AStm

B221-02. the system shall be such that it provides

watertight roof to roof/roof to corner joint cover

expansion control system that is capable of

accommodating multidirectional seismic movement

without stress to its components. System shall

52 5.46 consist of metal profile that incorporates an - - -

universal aluminum base member designed to

accommodate various project conditions and roof

treatments. the cover plate shall be designed of

width and thickness required to satisfy movement

and loading requirements and secured to base

members by utilizing manufacturer’s pre-

engineered self-centering arrangement that freely

rotates / moves in all directions. the Self centering

arrangement shall exhibit circular sphere ends that

lock and slide inside the corresponding aluminum

extrusion cavity to allow freedom of movement and

the Joint System shall resists damage or

deterioration from the impact of falling ice,

exposure of moisture Barrier membrane in the

53 Joint System to have water tight joint is - - -

mandatoryto UV, airborne contaminants and

occasional foot traffic from maintenance personnel.

54 5.46.2 Provision

roof Joint requirement.

of 150 mm gap (material shall conform to Rmt 145.00 6,699.85 9,71,478.25 - -

Total Carried over to summary 25,19,46,970.64 -

Brick work with common burnt clay F.P.S. (non

55 6.1 modular) bricks of class - - -

designation 7.5 in foundation and plinth in:

56 6.1.2 Cement mortar 1:6 (1 cement : 6 coarse sand) Cum 66.38 7,132.25 4,73,403.09 - -

Providing and laying Autoclaved Aerated

concrete(AAC) blocks masonry with 150mm to 300

mm thick with Grade-1 AAC blocks of density 551 to

650 kg/cum conforming to IS:2185 (Part 3) in super

57 6.47 structure above plinth level up to floor V level with - - -

RCC band at sill level and lintel level with approved

block laying polymer modified adhesive mortar all

complete as per direction of Engineer-in-Charge.

(The payment of RCC band and reinforcement shall

Extra for brick work / AAC block masonry / Tile brick

59 6.5 masonry in superstructure above floor V level, for Cum 686.00 169.45 1,16,242.70 - -

each four floors or part thereof by

mechanical means.

Extra for half brick masonry in superstructure,

60 6.14 above floor V level for every Sqm 794.00 104.80 83,211.20 - -

four floors or part thereof by mechanical means.

Extra for providing and placing in position 2 Nos

third course of half brick masonry.

Total Carried over to summary 3,38,68,888.55 - -

Providing and fixing 18 mm thick gang saw cut,

mirror polished, premoulded and prepolished,

machine cut for kitchen platforms, vanitycounters,

window sills, facias and similar locations of required

size,approved shade, colour and texture laid over

20 mm thick base cementmortar 1:4 (1 cement : 4

coarse sand), joints treated with white

cement,mixed with matching pigment, epoxy touch

ups, including rubbing, curing,moulding and

polishing to edges to give high gloss finish etc.

63 8.2.2 Granite stone slab colour black, Cherry/Ruby red - - -

Providing edge moulding to 18 mm thick marble

stone counters, Vanities etc., including machine

66 8.3 polishing to edge to give high gloss finish etc. - - -

complete as per design approved by Engineerin-

Signature of Contractor Signature

Digitally signedofby

Items Ref. DESCRIPTION Rate (INR) Amount (INR)

Sl No. (DSR- Unit Quantity DSR-

DSR-2025 MR DSR-2023/2022 DSR-2025 NDSR Amount

Providing and fixing dry cladding upto 10 metre

heights with 30mm thick gang saw cut stone with

(machine cut edges) of uniform colour and size

upto 1mx1m, fixed to structural steel frame work

and/ or with the size upto 1mx1m, fixed to

structural steel frame work and/ or with the help of

cramps, pins etc. and sealing the joints with

approved weather sealant as per Architectural

drawing and direction of Engineer-in-charge.(The

steel frame work, stainless steel cramps and pins

69 8.20.1 Red sand stone - 30mm thick gang saw cut stone Sqm 630.00 2,902.65 18,28,669.50 - -

Extra for stone work for wall lining on exterior walls

70 8.19 of height more than 10 m from ground level for Sqm 472.50 165.85 78,364.13 - -

every additional height of 3 m or part there of

Providing and fixing structural steel frame (for dry

cladding with 30 mm

thick gang saw cut with machine cut edges sand

stone) on walls at all heights using M.S. square/

rectangular tube in the required pattern as per

architectural drawing, including cost of cutting,

bending, welding etc. The frame work shall be fixed

to the wall with the help of M.S brackets/ lugs of

angle iron/ flats etc. which shall be welded to the

frame and embedded in brick wall with cement

concrete block 1:2:4 (1cement :2 coarse sand :4

graded stone aggregate 20 mm nominal size) of size

71 8.21 300x230x300 mm, including cost of necessary Kg 5,040.00 269.95 13,60,548.00 - -

centring and shuttering and with approved

expansion hold fasteners on CC/RCC surface,

including drilling necessary holes. Approved

cramps/ pins etc.shall be welded to the frame work

to support stone cladding, the steel work will be

given a priming coat of Zinc primer as approved by

Engineer in-charge and painted with two or more

coats of epoxy drawings shall be submitted by the

contractor to the Engineer-in-chargepaint (Shop for

approval before execution). The frame work shall

be fixed in true horizontal & vertical lines/planes.

(Only structural steel frame work shall be measured

Providing and fixing adjustable stainless steel

cramps of approved quality,required shape and

size, adjustable with stainless steel nuts, bolts and

washer (total weight not less than 260 gms), for dry

stone cladding fixed on frame work at suitable

location, including making necessary recesses in

stone slab, drilling required holes etc complete as

per direction of the

Engineer-in-charge.

Total Carried over to summary 60,38,486.43 - -

WOOD & PVC WORK

Providing wood work in frames of doors, windows,

clerestory windows and other frames, wrought

73 9.1 framed and fixed in position with hold fast lugs or - - -

with dash fasteners of required dia & length ( hold

fast lugs or dash fastener

shall be paid for separately).

Providing and fixing ISI marked flush door

shutters conforming to IS : 2202 (Part I)

75 9.2 decorative type, core of block board - - -

construction with frame of 1st class hard wood

and well matched teak 3 ply veneering with

vertical grains or cross bands and face veneers

35 mm thick including ISI marked Stainless

Steel butt hinges with necessary

77 9.7.7 Float glass panes - - -

5.0 mm thick glass panes (weight not less than

Providing and fixing wooden moulded beading to

79 9.40.1 door and window frames with iron screws, plugs - - -

and priming coat on unexposed surface etc.

Providing & fixing Anchor Fastners of 200 mm long

81 M.R to frame with 10 mm diameter bolts, nuts and Each 12.00 232.00 - - 2,784.00

plugs and embedding in cement concrete.

Providing and fixing aluminium sliding door bolts,

ISI marked anodised (anodic coating not less than

82 9.96 grade AC 10 as per IS : 1868), transparent or dyed Each - - -

to required colour or shade, with nuts and screws

etc. complete :

Signature of Contractor Signature

Digitally signedofby

Items Ref. DESCRIPTION Rate (INR) Amount (INR)

Sl No. (DSR- Unit Quantity DSR-

DSR-2025 MR DSR-2023/2022 DSR-2025 NDSR Amount

Providing and fixing aluminium tower bolts, ISI

marked, anodised (anodic coating not less than

84 9.97 grade AC 10 as per IS : 1868 ) transparent or dyed - - -

to required colour or shade, with necessary screws

etc. complete :

Providing and fixing aluminium handles, ISI marked,

anodised (anodic coating not less than grade AC 10

86 9.1 as per IS : 1868) transparent or dyed to required - - -

colour or shade, with necessary screws etc.

Providing and fixing aluminium hanging floor door

stopper, ISI marked, anodised (anodic coating not

88 9.101 less than grade AC 10 as per IS : 1868) transparent - - -

or dyed to required colour and shade, with

necessary screws

89 9.101.1 Single rubber stopper Each 4.00 39.60 158.40 - -

Providing and fixing factory made uPVC glazed/wire

mesh windows/doors comprising of lead free uPVC

multi-chambered frame, sash and mullion/coupler

(where ever required) extruded profiles having

minimum wall thickness of 1.70 mm for Series R1

and R2 profiles and 2.10 mm for Series R3 and R4

profiles conforming to EN: 12608 in any shape,

colour and design duly reinforced with galvanized

mild steel section made of required shape & size as

per CPWD Specification, uPVC extruded glazing

beads, interlocks and Inline sash adaptor (where

ever required) of appropriate dimension, EPDM

gasket, hardware, SS 304 grade fasteners of

minimum 8 mm dia with countersunk head,

comprising of matching polyamide PA6 grade sleeve

for fixing frame to finished wall as per IS 1367 : Part

1 to 14, plastic packers, plastic caps and necessary

stainless steel screws etc. Profile of frame, sash &

90 9.147A mullion (if required) shall be mitred cut and fusion - - -

welded/mechanically jointed duly sealed at all

corners, including drilling of holes for fixing

hardware and drainage of water etc. After fixing

frame the gap between frame and adjacent finished

wall shall be filled with weather proof silicon

sealant over backer rod of approved size and

quality, all complete as per approved drawing

conforming to CPWD specification & direction of

Engineer-in-Charge. Section of steel reinforcement

and cross sections of uPVC profiles to be as per

design approved by Engineer-in- Charge. Wire mesh

/ Glazing of plain/ toughened/ laminated/ double

glass unit with / without high performance coatings

as per design requirements and conforming to IS:

3548 & IS: 16231 shall be paid separately.

Note:- Structural design proof checked from a

Government Engineering Institute, to be provided

by the manufacturer for : (i) Sites with basic wind

Three track three panels sliding window with two

91 9.147.A4 glazed & one wire mesh panels with Aluminium - - -

channel for roller track, wool pile, nylon rollers with

Using R3 series with frame (98mm & above) x

9.147.A4. (40mm & above) & both

2 glazed and fly screen every glazed panel along with

multi-point locking system. (Height upto 1.8m).

Using R3 series with frame (55mm & above) x

(40mm & above) & sash (30mm & above) x (55mm

9.147.A1. & above) with zinc alloy (zamak) powder coated

2 handle on every panel along with multi-point

locking system (Height upto

94 9.147.C1 Fixed window / ventilator without mullion / - - -

9.147.C1. Using R1 series with frame (33mm & above ) x

upto 0.90 metre)

Providing and fixing M.S. grills of required pattern in

frames of windows etc.

96 9.48 with M.S. flats, square or round bars etc. including - - -

priming coat with approved steel primer all

97 9.48.1 Fixed to steel windows by welding Kg 45,024.00 219.10 98,64,758.40 - -

Total Carried over to summary 3,11,28,802.41 - 2,784.00

Signature of Contractor Signature

Digitally signedofby

Items Ref. DESCRIPTION Rate (INR) Amount (INR)

Sl No. (DSR- Unit Quantity DSR-

DSR-2025 MR DSR-2023/2022 DSR-2025 NDSR Amount

Steel work in built up tubular (round, square or

rectangular hollow tubes etc.) trusses etc.,

98 10.16 including cutting, hoisting, fixing in position and - - -

applying a priming coat of approved steel

primer, including welding and bolted with

special shaped washers etc. complete.

99 10.16.1 Hot finished welded type tubes Kg 300.00 - - -

eel work welded in built up sections/ framed

work, including cutting, hoisting, fixing in

100 10.25 position and applying a priming coat of - - -

approved steel primer using

structural steel etc. as required.

In gratings, frames, guard bar, ladder, railings,

brackets, gates and similar w

Providing and fixing stainless steel ( Grade 304)

railing made of Hollow tubes, channels, plates etc.,

including welding, grinding, buffing, polishing and

making curvature (wherever required) and fitting

the same with necessary stainless steel nuts and

bolts complete, i/c fixing the railing with necessary

accessories & stainless steel dash fasteners ,

stainless steel bolts etc., of required size, on the top

of the floor or the side of waist slab with suitable

arrangement as per approval of Engineer-incharge,

(for payment purpose only weight of stainless steel

members shall be considered excluding fixing

Total Carried over to summary 17,61,072.00 - -

Providing and laying Vitrified tiles in floor in

different sizes (thickness to be specified by the

manufacturer) with water absorption less than

0.08% and conforming to IS:15622, of approved

brand & manufacturer, in all colours and shade, laid

on 20 mm thick cement mortar 1:4 (1 cement: 4

103 11.41A coarse sand) jointing with grey cement slurry @3.3 - - -

kg/sqm including grouting the joints with white

cement and matching pigments etc. The tiles must

be cut with the zero chipping diamond cutter only .

Laying of tiles will be done with the notch trowel,

plier, wedge, clips of required thickness, leveling

system and rubber mallet for placing the tiles gently

104 11.41A.1 Double Charged Vitrified tile Polished Finish of Size - - -

Providing and laying Vitrified tiles in different sizes

(thickness to be specified by manufacturer), with

water absorption less than 0.08 % and conforming

I.S. 15622, of approved make, in all colours &

shade, in skirting, riser of steps, over 12 mm thick

bed of cement mortar 1:3 (1 cement: 3 coarse

sand), jointing with grey cement slurry @ 3.3 kg/

11.46.2 Size including grouting

Tile 600x600 mmthe joint with white cement Sqm 972.00 1,623.05 15,77,604.60 - -

Chequered terrazo tiles 22 mm thick with graded

marble chips of size up to 6 mm in floors, jointed

108 11.19 with neat cement slurry mixed with pigment to - - -

match the shade of the tiles, including rubbing and

polishing complete, on 20 mm thick bed of cement

mortar 1:4 (1 cement :4 coarse sand) :.

109 11.19.1 Light shade pigment using white cement Sqm 1,533.80 - - -

Providing and laying rectified Glazed Ceramic floor

tiles of size 300x300 mm or more (thickness to be

specified by the manufacturer), of 1st quality

conforming to IS : 15622, of approved make, in

colours White, Ivory, Grey, Fume Red Brown, laid

on 20 mm thick cement mortar 1:4 (1 Cement: 4

Coarse sand), jointing with grey cement slurry @

3.3 kg/ sqm including grouting the joints with white

andmatching pigments

laying flamed etc.,

finish complete

flooring in required design and patterns, in linear as

well as curvilinear portions of the building all

complete as per the architectural drawings with 18

mm thick stone slab over 20 mm (average) thick

base of cement mortar 1:4 (1 cement : 4 coarse

sand) laid and jointed with cement slurry and

pointing with white cement slurry admixed with

pigment of matching shade including rubbing,

curing and polishing etc. all complete as specified

Flamed finish granite stone slab Jet Black, Cherry

Signature of Contractor Signature

Digitally signedofby

Items Ref. DESCRIPTION Rate (INR) Amount (INR)

Sl No. (DSR- Unit Quantity DSR-

DSR-2025 MR DSR-2023/2022 DSR-2025 NDSR Amount

Providing and laying Polished Granite stone flooring

in required design and patterns, in linear as well as

curvilinear portions of the building all complete as

per the architectural drawings with 18 mm thick

stone slab over 20 mm (average) thick base of

113 11.56 cement mortar 1:4 (1 cement : 4 coarse sand) laid - - -

and jointed with cement slurry and pointing with

white cement slurry admixed with pigment of

matching shade including rubbing, curing and

polishing etc. all complete as specified and as

directed by the Engineer-in-

Polished Granite stone slab of colour Black,

Cherry/Ruby Red or equivalent

Providing and fixing Ist quality ceramic glazed

wall tiles conforming to IS: 15622 (thickness to

be specified by the manufacturer), of approved

make, in all colours, shades except burgundy,

bottle green, black of any size as approved by

115 8.31 Engineer-in-Charge, in skirting, risers of steps Sqm 2,408.00 1,267.95 30,53,223.60 - -

and dados, over 12 mm thick bed of cement

mortar 1:3 (1 cement : 3 coarse sand) and

jointing with grey cement slurry @ 3.3kg per

sqm, including pointing in white cement mixed

with pigment of matching shade complete.

Total Carried over to summary 2,74,42,211.65 - -

Providing and fixing mineral fibre false ceiling tiles

at all heights of size 595X595mm of approved

texture, design and pattern. The tiles should have

Humidity Resistance (RH) of 99%Light Reflectance ≥

85%, Thermal Conductivity k = 0.052 - 0.057 w/m K,

Fire Performance as per (BS 476 pt - 6 &7)in true

horizont al level suspended on interlocking T-Grid

of hot dipped all round galvanized iron section of

0.33 mm thick (galvanized @120 gsm) comprising

of main T runners of 15x32 mm of length 3000 mm,

cross T of size 15x32mm of length 1200 mm and

secondary intermediate cross T of size 15x32 mm of

length 600 mm to form grid module of size 600x600

mm suspended from ceiling using galvanized mild

steel item (galvanised@80gsm) 50 mm long 8mm

outer diameter M-6 dash fasteners, 6 mm diameter

fully threaded hanger rod up to 1000 mm length

and L- shape level adjuster of size 85x25x2 mm,

spaced at 1200 mm centre to centre along main ‘T’.

The system should rest on periphery walls

/partitions with the help of GI perimeter wall angle

of size24x24X3000 mm made of

0.40 mm thick sheet, to be fixed to the wall with

help of plastic rawl plug at 450 mm centre to centre

& 40 mm long dry wall S.S.screws. The exposed

bottom portion of all T-sections used in false ceiling

support system shall be pre-painted with polyester

baked paint, for all heights. The work shall be

mmasthick beveled tegular mineral fibre

117 26.27.1 false ceiling tile (NRC 0.55 to - - -

Providing corrugated G.S. sheet roofing including

vertical / curved surface fixed with polymer coated J

or L hooks, bolts and nuts 8 mm diameter with

bitumen and G.I. limpet washers or with G.I. limpet

washers filled with white lead, including a coat of

approved steel primer and two coats of approved

paint on overlapping of sheets complete (up to any

pitch in horizontal/ vertical or curved surfaces),

excluding the cost of purlins, rafters and trusses

and including cutting to size and shape wherever

0.80 mm thick with zinc coating not less than 275

Providing and fixing 15 cm wide, 45 cm overall semi-

circular plain G.S. sheet gutter with iron brackets

120 12.7 40x3mm size, bolts, nuts and washers etc., - - -

including making necessary connections with rain

water pipes complete.

0.80 mm thick with zinc coating not less than 275

Total Carried over to summary 2,42,81,285.45 - -

122 13.16 6 mm cement plaster of mix : - -

Signature of Contractor Signature

Digitally signedofby

Items Ref. DESCRIPTION Rate (INR) Amount (INR)

Sl No. (DSR- Unit Quantity DSR-

DSR-2025 MR DSR-2023/2022 DSR-2025 NDSR Amount

15 mm cement plaster on rough side of single or

half brick wall of mix:

128 13.6 20 mm cement plaster of mix : - - -

Polishing in high gloss/matt finish melamine clear

required color/wooden shade texture

Providing and applying plaster of paris putty of

131 13.26 2mm thickness over plastered surface to prepare Sqm 30,000.00 262.70 78,81,000.00 - -

the surface even and smooth complete.

Wall painting with premium acrylic emulsion paint

of interior grade, having VOC (Volatile Organic

132 13.83 Compound ) content less than 50 grams/ litre of - - -

approved brand and manufacture, including

applying additional coats wherever required to

achieve even shade and colour.

With water thinnable cement primer on wall

134 13.85.3 surface having VOC content Sqm 8,034.00 73.95 5,94,114.30 - -

less than 50 grams/litre

Finishing walls with Premium Acrylic Smooth

135 13.47 exterior paint with Silicone additives of required - - -

New work (Two or more coats applied @ 1.43 ltr/10

136 13.47.1 sqm over and including priming coat of Sqm 6,527.00 171.10 11,16,769.70 - -

exterior primer applied @ 0.90 litre/10 sqm)

Painting on G.S. sheet with synthetic enamel paint

137 13.53 of approved brand and - - -

manufacture ofrequired colour to give an even

New work (two or more coats) including a coat of

138 13.53.1 approved steel primer but Sqm 1,592.00 180.85 2,87,913.20 - -

excluding a coat of mordant solution

Total Carried over to summary 3,39,02,988.92 - -

WATERPROOFING WORK

Providing impervious coat to RCC roof slab required

slopes with CM (173) prop. 20tnm thick (average)

mixed with 1 kg Of water proofing compound per

bag Cementt laid Over roof slab when it is green,

finished smooth with a floating coat of neat cement

and thread lining at regular intervals of 45cmx45cm

139 NDSR imluding cost conveyance of all materials like sand. Sqm 2,700.00 925.12 - - 24,97,824.00

water proofing compound, water etc., to site,

seigniorage charges. sales & other taxes on all

materials operational, incidental, and lat»ur charges

for mixing mortar, laying, lift charges. rendering

smooth and thread lining. curing including rounding

Off the wall and slab junction etc., complete for

finished item of work. for:-lmpervious coat CM(1

Providing and laying water proofing treatment in

sunken portion of WCs, bathroom etc., by applying

cement slurry mixed with water proofing cement

compound consisting of applying :

(a) First layer of slurry of cement @ 0.488 kg/sqm

mixed with water proofing cement compound @

0.253 kg/ sqm. This layer will be allowed to air cure

(b) Second layer of slurry of cement @ 0.242

kg/sqm mixed with water proofing cement

compound @ 0.126 kg/sqm. This layer will be

allowed to air cure for 4 hours followed with

water curing for 48 hours. The rate includes

preparation of surface, treatment and sealing of all

joints, corners, junctions of pipes and masonry

Total Carried over to summary 1,54,262.50 - 24,97,824.00

ALUMINIUM & GLASS WORK

Signature of Contractor Signature

Digitally signedofby

Items Ref. DESCRIPTION Rate (INR) Amount (INR)

Sl No. (DSR- Unit Quantity DSR-

DSR-2025 MR DSR-2023/2022 DSR-2025 NDSR Amount

Providing and fixing aluminium work for doors,

windows, ventilators and partitions with extruded

built up standard tubular sections/ appropriate Z

sections and other sections of approved make

conforming to IS: 733 and IS: 1285, fixing with dash

fasteners of required dia and size, including

necessary Filling up the gaps at junctions, i.e. at top,

141 21.1 bottom and sides with required EPDM rubber/ - - -

neoprene gasket etc. Aluminium sections shall be

smooth, rust free, straight, mitred and jointed

mechanically wherever required including cleat

angle, Aluminium snap beading for glazing /

paneling, C.P. brass / stainless steel screws, all

complete as per architectural drawings and the

directions of Engineer-in-charge. (Glazing, paneling

142 21.1.1 For fixed portion - - -

Powder coated aluminium (minimum thickness of

For shutters of doors, windows & ventilators

including providing and fixing hinges/ pivots and

144 21.1.2 making provision for fixing of fittings wherever - - -

required including the cost of EPDM rubber /

neoprene gasket required (Fittings shall

be paid for separately)

Powder coated aluminium (minimum thickness of

Providing and fixing glazing in aluminium door,

window, ventilator shutters and partitions etc. with

146 21.3 EPDM rubber / neoprene gasket etc. complete as - - -

per the architectural drawings and the directions of

engineer-in-charge . (Cost of aluminium snap

beading shall be paid in basic item):

With float glass panes of 5 mm thickness (weight

Total Carried over to summary 7,04,930.04 - -

STRUCTURAL GLAZING

Providing and supplying aluminium extruded

tubular and other aluminium sections as per the

architectural drawings and approved shop drawings

, the aluminium quality as per grade 6063 T5 or T6

as per BS 1474,including super durable powder

coating of 60-80 microns conforming to AAMA

2604 of required colour and shade as approved by

the Engineer-in-Charge. ( The item includes cost of

material such as cleats, sleeves, screws etc.

necessary for fabrication of extruded aluminium

frame work. Nothing extra shall be paid on this

account). The weight of aluminium extruded

Designing, fabricating, testing, protection, installing

and fixing in position semi (grid) unitized system of

structural glazing (with open joints) for linear as

well as curvilinear portions of the

building for all heights and all levels, including:

(a) Structural analysis & design and preparation of

shop drawings for the specified design loads

conforming to IS 875 part III (the system must

passed the proof test at 1.5 times design wind

pressure without any failure), including functional

design of the aluminum sections for fixing glazing

panels of various thicknesses, aluminium cleats,

sleeves and splice plates etc. gaskets, screws,

149 toggles, nuts, bolts, clamps etc., structural and - - -

weather silicone sealants, flashings, fire stop

(barrier)-cum-smoke seals, microwave cured EPDM

gaskets for water tightness, pressure equalisation &

drainage and protection against fire hazard

(b) Fabricating and supplying serrated M.S. hot dip

galvanised / Aluminium alloy of 6005 T5 brackets of

required sizes, sections and profiles etc. to

accommodate 3 Dimentional movement for

achieving perfect verticality and fixing structural

glazing system rigidly to the RCC/ masonry/

structural steel framework of building structure

using stainless steel anchor fasteners/ bolts, nylon

Signature of Contractor Signature

Digitally signedofby

Items Ref. DESCRIPTION Rate (INR) Amount (INR)

Sl No. (DSR- Unit Quantity DSR-

DSR-2025 MR DSR-2023/2022 DSR-2025 NDSR Amount

(c) Providing and filling, two part pump filled,

structural silicone sealant and

one part weather silicone sealant compatible with

the structural silicone sealant of required bite size

in a clean and controlled factory / work shop

environment, including double sided spacer tape,

setting blocks and backer rod, all of approved

grade, brand and manufacture, as per the approved

sealant design, within and all around the perimeter

for holding glass.

(d) Providing and fixing in position flashings of solid

aluminium sheet 1 mm thick and of sizes, shapes

and profiles, as required as per the site conditions,

to seal the gap between the building structure and

all its interfaces with curtain glazing to make it

(e) Making provision for drainage of moisture/

water that enters the curtain glazing system to

150 25.2 make it watertight, by incorporating principles of - - -

pressure equalization, providing suitable gutter

profiles at bottom (if required), making necessary

holes of required sizes and of required numbers etc.

complete. This item includes cost of all inputs of

designing, labour for fabricating and installation of

aluminium grid, installation of glazed units, T&P,

scaffolding and other incidental charges including

wastages etc., enabling temporary structures and

services, cranes or cradles etc. as described above

and as specified. The item includes the cost of

getting all the structural and functional design

including shop drawings checked by a structural

designer, dully approved by Engineer-in-charge. The

item also includes the cost of all mock ups at site,

cost of all samples of the individual components for

testing in an approved laboratory,

field tests on the assembled working structural

glazing as specified, cleaning and protection till the

Note:-2. The following performance test are to be

conducted on structural glazing system if area of

structural glazing exceeds 2500 Sqm from the

certified laboratories accreditated by NABL(National

Accreditation Board for Testing and Calibration

Laboratories), Department of Science &

Technologies, India. Cost of testing is payable

separately. The NIT approving authority will decide

the necessity of testing on the basis of cost of the

work, cost of the test and importance of the work.

Performance Testing of Structural glazing system

Tests to be conducted in the NABL accredited lab or

any other accreditation body which operates in

accordance with ISO/IEC 17011 and accredits labs

as per ISO/IEC 17025

151 1. Performance Laboratory Test for Air Leakage Test Sqm 162.00 3,510.50 5,68,701.00 - -

(-50pa to - 300pa) & (+50pa to +300pa) as per

ASTM E-283-04 testing method for a range of

testing limit 1 to 200 mVhr

2. Static Water Penetration Test. (50pa to 1500pa)

as per ASTME- 331-09 testing method for a range

3. Dynamic Water Penetration (50pa to 1500pa) as

per AAMA 501.01- 05 testing method for a range

4. Structural Performance Deflection and

deformation by static air pressure test (1.5 times

design wind pressure without any failure) as per

ASTME-330- 10 testing method for a range upto 50

5. Seismic Movement Test (upto 30 mm) as per

Signature of Contractor Signature

Digitally signedofby

Items Ref. DESCRIPTION Rate (INR) Amount (INR)

Sl No. (DSR- Unit Quantity DSR-

DSR-2025 MR DSR-2023/2022 DSR-2025 NDSR Amount

Providing, assembling and supplying vision glass

panels (IGUs) comprising of hermetically-sealed 6-

12- 6 mm insulated glass (double glazed) vision

panel units of size and shape as required and

specified, comprising of an outer heat strengthened

float glass 6mm thick, of approved colour and

shade with reflective soft coating on surface # 2 of

approved colour and shade, an inner Heat

strengthned clear float glass 6mm thick, spacer

tube 12mm wide,dessicants, including primary seal

and secondary seal (structural silicone sealant) etc.

all complete for the required performances, as per

the Architectural drawings, as per the approved

shop drawings, as specified and as directed by the

Engineer-in-Charge. The IGUs shall be assembled in

the factory/ workshop of the glass processor.

(Payment for fixing of IGU Panels in the curtain

glazing is included in cost of item No.25.2) For

payment, only the actual area of glass on face # 1 of

the glass panels (excluding the areas of the grooves

(i) Coloured tinted float glass 6mm thick substrate

with reflective soft coating on face # 2, + 12mm

Airgap + 6mm Heat Strengthened clear Glass of

approved make having properties as visible Light

153 transmittance (VLT) of 25 to 35 %, Light reflection Sqm 162.00 3,718.70 6,02,429.40 - -

internal 10 to 15%, lightreflection external 10 to

20 %, shading coefficient (0.25- 0.28) and U value of

3.0 to 3.3 W/m2 degree K etc. The properties of

performance glass shall be decided by technical

Providing and Fixing of GRC Jali (Glass Fibre

Reinforced Jali) 50 mm thick of required size,

pattern, design, and colour with 50% area covered

154 M.R to be fixed on/between RCC / Block work Column or Sqm 143.64 5,369.00 - - 7,71,203.16

structural steel work with Dry Fixing method.

Pattern and design as approved by

Architect/Engineer-In-

Design, supply, fabrication and fixing of Signage

board using words made of acrylic cut out letters

with LED and reflective vinyl sheet as per approved

design with following specification.Board shall be

fabricated with 3 mm thick ACP sheets of approved

make. Powder coated Aluminium sheet shall be

fixed from the rear side of the entire board to make

box section. Logo letters (Telegu and English) shall

be made of Acrylic cutout letters of approved make

and shall be uniformly illuminated by using Digital

LED light of approved make. Powder coated

155 M.R Aluminum clips and brackets shall be used of LS 1.00 10,00,000.00 - - 10,00,000.00

minimum 3 mm thickness as per direction of

Engineer In charge.

Words of other matter of the signage board shall be

fixed using reflective vinyl cutout letters of

approved make. Lumpsum rate to be quoted for

following signages

1) "District Court Complex Bhimavaram" (In English)

Size: 2ft X 18ft

2) "District Court Complex Bhimavaram" (In Telegu)

Size: 2ft X 18ft

3) Logo of Ashoka Chakra as shown in the elevation

Total Carried over to summary 18,42,296.40 - 17,71,203.16

BOQ - Plumbing & Sanitary

Providing and fixing white vitreous china extended

wall mounting water closet of size mm of approved

including providing & fixing white vitreous china

156 17.78 cistem with dual flush fifing, of flushing capacity 3 Each 124.00 14,999.15 18,59,894.60 - -

litre/ 6 litre (adjustable to 4 litre/ 8 litres), including

seat cover, and cistern fitings, nuts,

bolts and gasket

Providing etc wash

and fixing complete.

basin with C.I. brackets,

15 mm dia CP Brass single hole basin mixer of

157 17.7A approved quality and make. including painting of - - -

fittings and brackets, cutting and making good the

walls wherever required:-

White Vitreous China Wash basin size 550x400 mm

single hole basin mixer

Providing and fixing white vitreous china pedestal

159 17.8 for wash basin completely recessed at the back for Each 157.00 1,683.35 2,64,285.95 - -

the reception of pipes and fittings.

Signature of Contractor Signature

Digitally signedofby

Items Ref. DESCRIPTION Rate (INR) Amount (INR)

Sl No. (DSR- Unit Quantity DSR-

DSR-2025 MR DSR-2023/2022 DSR-2025 NDSR Amount

Providing and fixing white vitreous china battery

based infrared sensor operated urinal of approx.

size 610 x 390 x 370 mm having pre & post flushing

160 17.80 with water (250 ml & 500 ml consumption), having Each 84.00 7,979.20 6,70,252.80 - -

water inlet from back side, including fixing to wall

with suitable brackets all as per manufacturers

Providing andand direction

fixing of Engineer-in-charge.

Urinal Division Plate with table

rubbed, edges rounded and polished, of size 900 x

450 mm, fixed in urinal partitions by cutting a chase

161 MR-1 of appropriate width with chase cutter and Each 84.00 6,546.16 - - 5,49,877.44

embedding the stone in the chase with epoxy grout

or with cement concrete 1:2:4 (1 cement : 2 coarse

sand : 4 graded stone aggregate 6 mm nominal size)

as per direction

Providing of Engineer-in-charge

and fixing Stainless Steel A ISIand

kitchen Sink as per IS:13983 with C.I. brackets and

162 17.10 stainless steel plug 40 mm, including painting Of - - -

fittings and brackets, cutting and making good the

163 17.10.1 Kitchen sink with drain board - - -

Suplying and fixing of Waste Coupling – Full Thread

Range:Allied,Material:Brass,Description:Waste

Coupling – Full Thread 32MM

Providing and fixing CP Brass 32 mm size Bottle

166 17.22A Trap of approved quality & make and as per the Each 157.00 1,034.80 1,62,463.60 - -

direction of Engineer-in-charge.

Providing and fixing P.V.C. waste pipe for sink or

167 17.28 wash basin including P.V.C. - - -

waste fittings com lete.

Providing and fixing mirror of superior glass (of

approved quality) and of

169 17.32 required shape and size with plastic moulded frame - - -

of approved make and shade with 6 mm thick hard

171 17.34 Providing and fixing toilet paper holder : - - -

Providing and fixing C.P. brass angle valve for basin

mixer of approved quality conforming to IS:8931

Providing and fixing PTMT soap Dish Holder having

175 18.65 length of 138 mm, breadth 102 mm, height of 75 Each 157.00 111.45 17,497.65 - -

mm with concealed fitting arrangements,

weighing not less than 106 gms.

Providing and fixing SS grade 316 trapezoidal shape

215 mm long, 200 mm wide with minimum

176 MR-3 distances of 37 mm from wall face with concealed Each 157.00 231.95 - - 36,416.15

fittings arrangement of approved quality and

colour, weighing not less than

Providing of C.P Towel rack with all accessories as

177 MR-4 per approved specifications with 600 mm length, SS Each 32.00 2,877.41 - - 92,077.12

304, and making good the walls wherever required

Providing and fixing of 15 mm dia C.P. brass Pillar

178 cock with CP wall flange of approved quality with - - -

flow rate of 5 LPM complying to Green Building

180 For Sink - - -

Providing of C.P WALL MOUNTED SWIVEL SPOUT

KITCHEN SINK MIXER with

181 MR-6 all accessories as per approved specifications, Each 4.00 2,841.84 - - 11,367.36

Material: Brass,Mounted : Wall mounted,Series

Supplying of Health Faucet,

Material:Brass,Description:Health Faucet With Tube

182 MR-7 1 Meter & Hook,Finish:Chrome,Dimension Each 124.00 3,337.47 - - 4,13,846.28

Providing of C.P 2 WAY ANGLE COCK with Wall

183 MR-8 Flange and all accessories as per approved Each 124.00 2,105.16 - - 2,61,039.84

specifications, Material: Brass,Mounted : Wall

Supplying and fixing of Twin Coat Hook:Material:18-

steel,Application:WC Cubicle Area,Warranty:1 year.

Providing and fixing of FLOOR DRAIN WITH

185 MR-10 COCKROACH TRAP, Dimensions : 5X5 INCH, Shape: Each 285.00 1,852.67 - - 5,28,010.95

Square Flat Cut,Material: Stainless steel 304, Finish:

Gloss/Matt, Warranty : 1 Year

Signature of Contractor Signature

Digitally signedofby

Items Ref. DESCRIPTION Rate (INR) Amount (INR)

Sl No. (DSR- Unit Quantity DSR-

DSR-2025 MR DSR-2023/2022 DSR-2025 NDSR Amount

Providing of FLOOR DRAIN WITH HOLE AND

186 MR-11 COCKROACH TRAP, Dimensions - 6X6 INCH, Each 74.00 1,923.98 - - 1,42,374.52

Material: Stainless steel 304,

Finish: Steel, Warranty : 1 Year

Supplying of HI SPEED HAND DRYER Construction :

Steel #304,Mounting : Wall Mounted, Operation :

187 MR-12 Automatic, Hand Dry Time : 9S ,Auto Cutoff : 60 Each 38.00 26,067.39 - - 9,90,560.82

seconds, Noise Leve : 60-70db, Motor : brush

motor, Speed : 30000r/min, Voltage : 220-240V,

Rated Power : 1000W, Current : 6A

Supplying of S.STEEL SOAP DISPENSER Container :

188 MR-13 18-8 S, Type-304, Stainless Steel Material : Non Each 38.00 3,744.33 - - 1,42,284.54

Corrosive Steel, Capacity : 190 ML

Providing and fixing of vitreous China Sanitary

fixtures and CP fitting and other accessories for

Handicapped toilet . Each Matrix Set shall

189 MR-14 comprised (Wash Basin 650 x 350 with one pair Each 12.00 16,467.76 - - 1,97,613.12

mounting brackets, EWC & Cistern complete with

fittings & seat cover, one no hinged rail 76 cm and

five no's ofand

Providing grab rails of

fixing 601cm).

No. complete all respect.

Swing Handicap Grab

190 MR-15 Bar - Stainless Steel at Each 12.00 12,787.65 - - 1,53,451.80

fixed height for handicap toilet complete as

Providing and fixing of 1 No. Stainless Steel Grab

191 MR-16 Barl (600 Mm),32mm Dia. at fixed height for Each 12.00 5,226.33 - - 62,715.96

handicap toilet complete as required.

Providing and fixing of 1 No. Stainless Steel Grab

192 MR-17 Bar (350 Mm),32mm Dia. at fixed height for Each 12.00 4,689.46 - - 56,273.52

handicap toilet complete as required.

INTERNAL AND EXTERNAL SERVICES

Providing and fixing Chlorinated Polyvinyl Chloride

(CPVC) pipes, having thermal stability for hot & cold

water supply, including all CPVC plain & brass

threaded fittings and fixing the pipe with clamps at

1.00 m spacing. This includes jointing of pipes &

fittings with one step CPVC solvent cement and the

cost of cutting chases and making gocx:l the same

including testing of joints complete as per direction

of Engineerwork,

Concealed in Charge.

including cutting chases and

making the walls etc.

Providing and fixing Chlorinated Polyvinyl Chloride

(CPVC) pipes, having thermal stability for hot & cold

water supply including all CPVC plain & brass

198 18.9 threaded fittings This includes jointing of pipes & - - -

fittings with one step CPVC solvent cement,

trenching, refilling & testing of joints complete as

20 mmdirection of Engineer

nominal dia Pipes in Charge as per IS code Metre 352.00 274.30 96,553.60 - -

Providing and fixing gun metal non- return valve of

203 18.19 approved quality - - -

(screwed end) :

Providing, installation, testing and commissioning

-E&M- of stainless steel Y- strainer fabricated out of 1.6

2022/18 mm thick stainless steel, Grade 304, sheet with

3 mm dia holes with stainless steel flan e.

Providing and fixing gun metal gate valve with C.I.

wheel of approved quality screwed end

212 18.17.2 32 mm nominal bore. Each - 689.60

214 18.17.6 80 mm nominal bore Each - 2,604.55

Supplying, fixing, testing and commissioning of

DSR-E&M- butterfly valve of PN 1.6 rating with

215 2022// bronze/gunmetal seat duly ISI marked complete - - -

18.1 with nuts, bolts, washers, gaskets conforming to IS

13095 of following sizes as required :

Fixing Water meter and stop cock in G.I. pipe line

217 18.14 including cutting and threading the pipe and Each 4.00 812.30 3,249.20 - -

making long screws etc. complete (cost of water

meter and stop cock to be paid separately).

Signature of Contractor Signature

Digitally signedofby

Items Ref. DESCRIPTION Rate (INR) Amount (INR)

Sl No. (DSR- Unit Quantity DSR-

DSR-2025 MR DSR-2023/2022 DSR-2025 NDSR Amount

Providing and fixing Cl- sluice valves (with cap)

218 18.31 complete with bolts, nuts, rubber insertions etc. - - -

(the tail pieces if required will be paid separately) :

Constructing masonry Chamber 60x60x75 cm

inside, in brick work in cement mortar (1 cement : 4

coarse sand) for sluice valve, with C.I- surface 100

mm top diameter, 160 mm bottom diameter and

180 mm deep ( inside) with chained lid and RCC top

slab 1 : 1.5:3 mix (1 cement : 1.5 coarse sand : 3

graded stone aggregate 20 mm nominal size),

including necessary excavation, foundation

concrete 1 (1 cement : 5 fine : 10 graded stone

aggregate 40 mm nominal size) and inside

plastering with cement mortar 1-- 3 (1 cement 3

coarse sand) 12 mm thick, finished with a floating

With common burnt clay EPS-(non modular) bricks

of class designation 7.5

Providing and fixing C.I. dirt box strainer for bulk

223 18.61 type water meter with nutsi bolts, rubber insertions - - -

etc. complete conforming to IS : 2373 :

DSR-E&M- Providing and fixing in position the industrial type

225 2022 pressure gauges with gun metal/ brass valves Each 40.00 1,196.00 47,840.00 - -

/16.8 complete as required

Piston Operated Screwed End Nitrile Rubber Bronze

226 / Gun Metal Body - - -

Pressure Reducing Valve Size

Providing and fixing,testing and commissioning of

228 expansion Bellow,Material Rubber and GI - - -

Flange,Thread Size As per customers requirement

Providing water level indicator or Automatic water

230 MR-20 Level Indicator with Each 14.00 7,533.23 - - 1,05,465.22

Musical Alarm on Tank Full and Buzzer on Tank

Providing and placing on terrace (at all floor levels)

polyethylene water storage

tank, IS : 12701 marked, with cover and suitable Per

231 18.48 locking arrangement and making 26,000.00 11.00 2,86,000.00 - -

necessary holes for inlet, outlet and overflow pipes

but without fittings and the

Providing andfor tank

fixing GI fabricated hot dipped

galvanized coating puddle flange comprising of 600

mm dia long M.S class 'C' pipe (screwed end up to

50 mm & flange for more than 50 mm dia) with 6

mm thick M.S plates of required size including

232 cutting holes in Centre of plate, inserting pipe & - - -

making welded (Arc) joint complete. Same shall be

installed with TEC welded joint in position with

reinforcement bars of RCC tank wall/slab including

making cutout in shuttering during concrete casting

of tank of following diameter.(For

SEWERAGE & DRAINAGE NETWORK

Providing, laying, jointing & testing of following

P.V.C. pipes with solvent cement joint for 8 kg/ sq.

237 cm. pressures including testing of joints, cost of - - -

jointing materials etc. complete in all respect.(class

238 Concealed work - - -

TOTAL AMOUNT - - 30,34,295.86

TOTAL AMOUNT - - 30,34,295.86

BOQ - Internal Electrical

A A DISTRIBUTION BOARDS

Supplying and fixing following way, single pole and

neutral, sheet steel, MCB distribution board, 240 V,

on surface/ recess, complete with tinned copper

243 2.3 bus bar, neutral bus bar, earth bar, din bar, - - -

interconnections, powder painted including

earthing etc. as required. (But without

244 2.3.2 MCB/RCCB/Isolator)

Signature of Contractor Signature

Digitally signedofby

Items Ref. DESCRIPTION Rate (INR) Amount (INR)

Sl No. (DSR- Unit Quantity DSR-

DSR-2025 MR DSR-2023/2022 DSR-2025 NDSR Amount

Supplying and fixing following way, horizontal type

three pole and neutral, sheet steel, MCB

distribution board, 415 V, on surface/ recess,

245 2.4 complete with tinned copper bus bar, neutral bus - - -

bar, earth bar, din bar, interconnections, powder

painted including earthing etc. as required. (But

246 2.4.1 without

4 way (4MCB/RCCB/Isolator)

Supplying and fixing 5 amps to 32 amps rating, 240

volts, 'C' series, miniature circuit breaker suitable

248 2.1 for inductive load of following poles in the existing - - -

MCB DB complete with connections, testing and

commissioning etc.

250 2.10.2 Single pole and neutral Each 29.00 599.00 17,371.00 - -

Supplying and fixing single pole blanking plate in

251 2.11 the existing MCB DB Each 30.00 13.00 390.00 - -

complete etc. as required.

Supplying and fixing following rating, double pole,

(single phase and neutral), 240 V, residual current

252 2.14 circuit breaker (RCCB), having a sensitivity current - - -

30 mA in the existing MCB DB complete with

connections, testing

and commissioning etc. as required.

Supplying, fixing, connecting, testing and

commissioning of following rating, ISI marked (IS

255 MR 8828) 240 / 415 volts, 10 KA, Miniature Circuit - - -

Breaker (MCB) of single / double / three / four poles

in the existing MCB DB or in existing MS enclosure

complete in all respects.

TOTAL CARRIED TO SUMMARY 7,28,155.00 - 90,317.00

Supply of XLPE insulated and PVC sheathed AL

259 armoured cable of 1.1 KV grade confirming to IS : - - -

7098:1988 with upto date amendments of

Laying and fixing of following sizes of one number

263 7.6 PVC insulated and PVC sheathed/XLPE Power cable - - -

of 1.1kv grade on cable tray as required.

264 7.6.1 Upto 35 sq. mm (clamped with 1mm thick saddle) Mtr 850.00 45.00 38,250.00 - -

Supplying and making end termination with brass

compression gland and aluminium lugs for

265 9.1 following size of PVC insulated and PVC sheathed / - - -

XLPE aluminium conductor cable of 1.1 KV grade as

TOTAL CARRIED TO SUMMARY 55,990.00 - 3,26,430.00

C. HOT DEEP GI CABLE TRAYS & GI RACEWAYS

Supplying and installing following size of perforated

Hot Dipped Galvanised Iron cable tray

(galvanisation thickness not less than 50 microns)

268 4.6 with perforation not more than 17.5%, in - - -

convenient sections, joined with connectors,

suspended from the ceiling with G.I. suspenders

269 4.6.2 including

150 mm widthG.I. X 50 mm depth X 1.6 mm thickness Metre 360.00 716.00 2,57,760.00 - -

270 4.6.4 300 mm width X 50 mm depth X 1.6 mm thickness Metre 225.00 963.00 2,16,675.00 - -

271 4.6.6 450 mm width X 50 mm depth X 2.0 mm thickness Metre 135.00 1,325.00 1,78,875.00 - -

272 4.6.11 600 mm width X 50 mm depth X 2.0 mm thickness Metre 90.00 1,909.00 1,71,810.00 - -

TOTAL CARRIED TO SUMMARY 8,25,120.00 - -

Earthing with G.I. earth plate 600 mm X 600 mm X 6

mm thick including accessories, and providing

273 5.4 masonry enclosure with cover plate having locking Each 24.00 7,472.00 1,79,328.00 - -

arrangement and watering pipe of 2.7 metre long

etc. with charcoal/

coke and salt as required.

Earthing with copper earth plate 600 mm X 600 mm

X 3 mm thick including accessories, and providing

274 5.6 masonry enclosure with cover plate having locking Nos 20.00 13,838.00 2,76,760.00 - -

arrangement and watering pipe of 2.7 metre long

etc. with charcoal/

coke and salt as required.

Signature of Contractor Signature

Digitally signedofby

Items Ref. DESCRIPTION Rate (INR) Amount (INR)

Sl No. (DSR- Unit Quantity DSR-

DSR-2025 MR DSR-2023/2022 DSR-2025 NDSR Amount

Providing and fixing 25 mm X 5 mm copper strip on

275 5.14 surface or in recess for Meter 205.00 1,162.00 2,38,210.00 - -

connections etc. as required.

Providing & fixing of 25mm x 5mm GI strip on

276 5.15 surface or recess for earth Meter 425.00 244.00 1,03,700.00 - -

connection as required.

Providing and fixing 6 SWG dia G.I. wire on surface

277 5.16 or in recess for loop Meter 150.00 70.00 10,500.00 - -

earthing as required.

TOTAL CARRIED TO SUMMARY 8,08,498.00 - -

E. INTERNAL WIRING:

Wiring for light point/ fan point/ exhaust fan point/

call bell point with 1.5 sq.mm FR PVC insulated

copper conductor single core cable in surface /

278 1.1 recessed medium class PVC conduit, with modular

switch, modular plate, suitable GI box and earthing

the point with 1.5 sq.mm. FR PVC insulated copper

279 1.10.3 conductor

Group C single core cable etc as required. Point 1,200.00 1,467.00 17,60,400.00 - -

Wiring for group controlled (looped) light point/fan

point/exhaust fan point/ call bell point (without

independent switch etc.) with 1.5 sq. mm FRLS PVC

280 1.55 insulated copper conductor single core cable in - - -

surface/ recessed steel conduit, and earthing the

point with 1.5 sq. mm FRLS PVC insulated copper

281 1.55.3 conductor

Group C single core cable etc. as required. Point 929.00 1,094.00 10,16,326.00 - -

Wiring for light/ power plug with 2X4 sq. mm FRLS

PVC insulated copper conductor single core cable in

282 1.5 surface/ recessed steel conduit alongwith 1 No. 4 meter 400.00 433.00 1,73,200.00 - -

sq. mm FRLS PVC insulated copper conductor single

core cable for loop

earthing as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS

PVC insulated copper conductor single core cable in

283 1.12 surface/ recessed medium class PVC conduit meter 2,500.00 334.00 8,35,000.00 - -

alongwith 1 No. 4 sq. mm FRLS PVC insulated

copper conductor single core

cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth

284 1.7 wire with the following sizes of FRLS PVC insulated - - -

copper conductor, single core cable in surface/

recessed steel conduit as required.

Wiring for circuit/ submain wiring alongwith earth

288 1.14 wire with the following sizes of FRLS PVC insulated - - -

copper conductor, single core cable in surface/

recessed PVC conduit as required.

Supplying and fixing suitable size GI box with

modular plate and cover in front on surface or in

291 1.31 recess, including providing and fixing 3 pin 5/6 A Each 354.00 477.00 1,68,858.00 - -

modular socket outlet and 5/6 A modular switch,

connections etc. as

Supplying and fixing suitable size GI box with

modular plate and cover in front on surface or in

292 1.56 recess, including providng and fixing 2 Nos. 3 pin Each 155.00 676.00 1,04,780.00 - -

5/6 A modular socket outlet and 2 Nos. 5/ 6 A

modular switch, connections etc. as required. (For

light plugs to be used in non residential buildings).

Supplying and fixing suitable size GI box with

modular plate and cover in front on surface or in

293 1.32 recess, including providing and fixing 6 pin 5/6 A & Each 410.00 586.00 2,40,260.00 - -

15/16 A modular socket outlet and 15/16 A

modular switch, connections etc.

Supplying and fixing two module stepped type

294 1.25 electronic fan regulator on the existing modular Each 316.00 369.00 1,16,604.00 - -

plate switch box including connections but

Supplying and fixing modular blanking plate on the

295 1.26 existing modular plate & Each 50.00 40.00 2,000.00 - -

switch box excluding modular plate as required.

Signature of Contractor Signature

Digitally signedofby

Items Ref. DESCRIPTION Rate (INR) Amount (INR)

Sl No. (DSR- Unit Quantity DSR-

DSR-2025 MR DSR-2023/2022 DSR-2025 NDSR Amount

Providing and fixing circular/hexagonal Fan box cast

iron /metal sheet Box for ceiling fan clamp of

internal dia 140mm , 73 mm height,Top id of

1.5mm thick MS sheet with its Top surface hacked

of proper bonding top lid shall be screwed into cast

iron /metal sheet Box by mean of 3.3mm dia round

headed screw one lock at the corners.clamp shall

be made of 12mm dia ms Bar band toshape as per

Supplyingdrawing.

and fixing 20 A, 240 V, SPN Industrial

type socket outlet, with 2 pole and earth, metal

enclosed plug top alongwith 20 A "C" curve, SP,

297 2.18 MCB, in sheet steel enclosure, on surface or in Each 44.00 1,621.00 71,324.00 - -

recess, with chained metal cover for the socket

outlet and complete with connections, testing and

TOTAL CARRIEDetc.

TO as required.

F. LIGHTING FIXTURE AND FANS

DSR E&M - LED Down lighter (SMD Type) (System lumen

2025 Vol efficacy >135 lm/Watt)

Supplying, installation, Testing & Commissioning

of LED Recessed / surface Down lighter (Round

/square/Rectangular) SMD type of following body

material with PMMA and prismatic diffuser and

construction as per IS

: 10322 with driver as per the requirement with

Driver efficiency >85%, Operating voltage AC 140-

270 Volt, freq 50/60 hz, Operating temp range - 15

deg to 40 deg centigrade, internal surge

protection of 2.5 KV with Short & Open circuit

protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80,

UGR (Unified Glare Rating) < 19, Flicker free, (flicker

should be below 5 %), life time (LED,Driver &

electrical circuitry), life time of minimum 50000

Burning Hours with , 70% of initial Lumen

maintained till life ends as per LM80

299 extrapolation IES TM-21-11 report, CCT 3000°K / - - -

Bin) , SDCM(Standard Deviation Color Matching)

<3, Maximum power consumption should not

more than the specified rating and Fixture shall be

of relevant BIS standard and trade mark certificate (

T.C.). Manufactures Word Mark/ Name Engraved/

Embossing/ Screen printing on housing. OEM

must have its own in house NABL lab setup for

all testing facilities for LED fixtures. complete in

all respect i/c connections with 1.5 sq mm

FRLS, PVC insulated copper conductor single core

cable and earthing etc. as required with Minimum 5

year OEM warranty. System lumen efficacy >135

output . LM79 & LM80 Test report from NABL lab

for all testing required for LED fixtures as per BIS

shall be submitted. Shape size and CCT shall be as

Powder coated die cast / Extruded aluminum

Body including trim.

DSR 12 -15 watt

Supply of 9W LED (mirror light) 2ft Batten with a

nominal system lumen output of 1150 lumens and

a minimum system efficacy of 115 lm/W. The

luminaire shall have a rated system lifetime of

25,000 burning hours at L70. The luminaire should

have a color temperature of 6500K and CRI>80. The

luminaire shall meet IP20 rating with THD < 20%

and PF > 0.9. The luminaire housing should made of

CRCA with a PC glossy diffuser. The total power

consumption should not exceed 10W (including

LED Batten light (System lumen efficacy >135

Signature of Contractor Signature

Digitally signedofby

Items Ref. DESCRIPTION Rate (INR) Amount (INR)

Sl No. (DSR- Unit Quantity DSR-

DSR-2025 MR DSR-2023/2022 DSR-2025 NDSR Amount

Supplying, installation, Testing & Commissioning of

LED surface mounted Batten light of following body

material and construction as per IS : 10322 with

driver (Replaceable) as per the requirement with

Driver efficiency

>85% ,Operating voltage AC 140-270 Volt, freq

50/60 hz, Operating temp range 15 deg to 40 deg

centigrade, internal surge protection of 2.5 KV with

Short & Open circuit protection ,THD < 10% , P.

F.≥0.95, IP20, CRI >80 , Flicker free (flicker should

be below 5 %), life time (LED,Driver & electrical

circuitry), of minimum 50000 Burning Hours

with , 70% of initial Lumen maintained till life

/6000°K/ 6500°K (As per ANSI Bin), SDCM

305 (Standard Deviation Color Matching) <3, Maximum - - -

power consumption should not more than the

specified rating and Fixture shall be of relevant BIS

standard and trade mark certificate ( T.C.).

Manufactures Word Mark/ Name Engraved/

Embossing/ Screen printing on housing. OEM must

have its own in house NABL lab setup for all

testing facilities for LED fixtures. complete in all

respect i/c connections with 1.5 sq mm FRLS,

PVC insulated copper conductor single core cable

and earthing etc. as required with Minimum 5 year

OEM warranty. System lumen efficacy >135

lm/Watt output . LM79 & LM80 Test report from

NABL lab for all testing required for LED

fixtures as per BIS shall be submitted. Shape size

and CCT shall be as approved by Engineerin-Charge

306 CRCA Sheet Body (Thickness ≥ 0.50 mm) - - -

DSR 24 -26 watt

Supply, Installation, Testing and Commissioning of

1200 mm sweep, BEE 5 star rated, ceiling fan with

Brush Less Direct Current (BLDC) Motor, class of

insulation: B, 3 nos. blades, 30 cm long down rod, 2

nos. canopies, shackle kit, safety rope, copper

winding, Power Factor not less than 0.9, Service

308 DSR 19.1 Value (CM/M/W) minimum 6.00, Air delivery No. 316.00 2,730.00 8,62,680.00 - -

minimum 210 Curn/Min , 350 RPM (tolerance as

per IS : 374-2019), THD less than 10%, remote or

electronic regulator unit for speed control and all

remaining accessories including safety pin, nut

bolts, washers, temperature rise=75 degree C

(max.), insulation resistance more than 2 mega

ohm, suitable for 230 V, 50 Hz, single phase AC

Supplying and Fixing of Exhaust Fan Heavy duty

TOTAL CARRIED TO SUMMARY 8,62,680.00 16,14,471.00 3,73,802.00

H LIGHTNING ARRESTER

Providing and fixing of lightning conductor finial,

310 DSR 6.2 made of 25 mm dia 300mm long, G.I. tube, having Each 10.00 518.00 5,180.00 - -

single prong at top, with 85mm dia 6mm thick G.I.

base plate i ncluding holes etc. complete as

Providing and fixing G.I. tape 20 mm X 3 mm thick

311 DSR 6.7 on parapet or surface of wall for lightning metre 90.00 126.00 11,340.00 - -

conductor complete as required.(For horizontal run)

Providing and fixing G.I. tape 20 mm X 3 mm thick

312 DSR 6.8 on parapet or surface of wall for lightning metre 60.00 197.00 11,820.00 - -

conductor complete as required.(For vertical run)

Providing and fixing testing joint, made of 20 mm X

313 DSR 6.12 3 mm thick G.I. strip, 125 mm long, with 4 nos. of Each 8.00 121.00 968.00 - -

G.I. bolts, nuts, chuck nuts and spring washers etc.

complete as required.

Earthing with G.I earth Pipe 4.5 metre long, 40mm

dia including accessories and providing masonry

314 DSR 5.2 enclosure with cover Plate having locking nos 8.00 6,855.00 54,840.00 - -

arrangement and watering pipe etc with charcoal

/coke and salt as required.

Jointing copper /G.I. tape (with another copper/ GI

315 DSR 6.4 tape, base of the finial or any other metallie object) Each 8.00 113.00 904.00 - -

by riveting /nut bolting/sweating and soldering

etc as required.

Providing and laying G.I. tape 32 mm X 6 mm from

316 DSR 6.14 earth electrode directly meter 140.00 195.00 27,300.00 - -

in ground as required.

TOTAL CARRIED TO SUMMARY 1,12,352.00 - -

Signature of Contractor Signature

Digitally signedofby

Items Ref. DESCRIPTION Rate (INR) Amount (INR)

Sl No. (DSR- Unit Quantity DSR-

DSR-2025 MR DSR-2023/2022 DSR-2025 NDSR Amount

Total - Internal Electrical 91,09,903.00 16,14,471.00 7,90,549.00

Signature of Contractor Signature

Digitally signedofby