Repairing & renovation work for providing canteen at Collector Office builing Valsad.Ta.Valsad Dist.Valsad

Name of work :-

Repairing & renovation work for providing canteen at Collector Office builing Valsad.Ta.Valsad Dist.Valsad

Bill of Quantities

(A) Percentage Rate Tender (Up to INR 50 Cr. )

Memorandum showing items of work to be carried out

Ite Quantity Unit Estimated Rates Total Amount

Ite Quantity Unit Estimated Rates Total Amount

No. Item of work In figure estimated

Rs. Ps. quantities

1 CEMENT SHEET PARTITION

Providing and fixing of full height Cement sheet partitions (AS PER 7.2 Sq. Mt 3011.00

DRAWINGS) using aluminium pipe for framing, 10mm plain cement sheet

of brand T.P.I,SHERA (single sides), etc. including all hardware item,

groove (if shown) with all material, labour,SCAFFOLDING, lead and

wastage etc. complete. And Finished with wall color and complete the

work satisfactorily as per instruction of architect or Engineer-in charge.

2 WOODEN PANELLING

Providing and making of panelling on Wall & columns using 12mm ply, 16.00 Sq. Mt 1398.00

aluminium pipe for (2" x 1") framing, Ghana bidding patti (11/2" x 3/4")

including all material, labour and hardware complete,including 3 mmx

3mm groove (if shown) with all materials,polish work,beading patti,

labour, lead and wastage etc. complete. And Finished with different

materials,and complete the work satisfactorily as per instruction of

architect or Engineer-in charge.

3 MIRROR FINISH(5mm thick Looking Mirror)

Providing and fitting of mirror/glass (as per drawing & approved shade)of 1.50 Sq. Mt 1593.00

brand ais,modiguard,etc on ply panelling / on tile cladding including all

material, labour and hardware, waste of materials and complete the

work satisfactorily as per instruction of architect or Engineer-in charge.

4 LAMINATE FINISH

Providing and fitting of 1 mm laminate (as per drawing & selection) on ply 16.00 Sq. Mt 924.00

partition of brand greenlam,merinolam or shivshakti, including all

material, adhesives,labour and hardware, waste of materials complete as

per instruction of architect.[Basic Rate of Laminate : 2000rs./sheet (8' x

4')] 3 mmx 3mm groove (if shown) with all materials,polish work,beading

patti, labour, lead and wastage etc. complete. And Finished with different

materials,and complete the work satisfactorily as per instruction of

architect or Engineer-in charge.

Providing and fixing Glass door of approx size 2.3 MT. x 2.1 MT.. dubale 3.00 No 16975.73

shutter using 12 mm toughned glass door with filmwork & wooden

handle & floor spring of brand fluid,ozone,dorma etc AS PER DRAWING

including all acceessories,locks, material, silicone,labour,installation, Hole

& slote charges etc. and complete the work satisfactorily as per

instruction of architect or Engineer-in charge.

6 GYPSUM CEILING

Supplying and Fixing of Suspended ceiling system components which 200.00 Sq. Mt 681.00

includes Single Layer Boarding with 12.5mm thick USG Boral Standard

Plasterboard This includes of USG Boral Thundersteel Perimeter Channel

(0.50mm thick having one flange of 20mm and another flange of 30mm

and a web of 28mm) screw fixed to brick wall/partition with the help of

approved screws at 600mm centers. Then suspending of USG Boral

Thundersteel Intermediate channel (45mm x 0.90mm thick with two

flanges of 15mm each) from the soffit at 1220mm centers with of USG

Boral Thundersteel Ceiling Angle (25 x 10mm x 0.50 mm thick) fixed to

RCC Slab with of USG Boral Soffit Cleat (37x27x25x1.6mm thick) and 8mm

dia 40mm long Anchor Fastener @ 600mm Centers, respectively. USG

Boral Thundersteel Ceiling Section (having web of 51 mm and two flanges

of 27mm each) are then fixed to the of USG Boral Thundersteel

Intermediate channel with the help of connecting clip (2.6mm Dia) and in

perpendicular direction to the USG Boral Thunder-steel intermediate

channel at 457mm centers. USG Boral Thundersteel profiles are rolled

with AZ Steel (150 GSM & 310 MPa Yield Strength) having base metal

conforming to IS 513:2016 as per IS 15961:2017/ AS 1397:2001).12.5mm

thick USG Boral Standard Plasterboards (confirming to IS 2095 Part 1) is

screw fixed with 25mm long Drywall screws at 230 mm centers. The

screw fixing of gypsum boards to the metal framing at the periphery,

openings and cut edges should be at 150mm centers.All the Gypsum

boards must be staggered. All joints to be taped & finished with

USGBORAL Paper tape & All-Purpose Joint Compound confirming to

ASTM C475. Material certificate to be provided by company. and

7 WALL COLOR - SATIN

Providing and applying satin paint of approved quality, company and 357.00 Sq. Mt 350.00

shade upto finishing (min 3 coats) including all material, labour including

scaffolding etc. and complete the work satisfactorily as per instruction of

architect or Engineer-in charge.

1 CEILING COLOR - PLASTIC PAINT

Providing and applying plastic paint of approved quality, company and 200.00 Sq.Mt. 220.00

shade upto finishing (min 3 coats) including all material, labour including

scaffolding etc. and complete the work satisfactorily as per instruction of

architect or Engineer-in charge.

8 ROLLER CURTAIN

Providing and fixing of approved quality roller blinds using phifer fabric of 17.80 Sq. Mt 1547.00

Premium grade, with roller tube, bottom bar leveller made of extruded

aluminium alloy an Idler, Insert Type- Brackets, PVC chain etc. all

complete at all floor and heights as per approved specification. Roller

Tube Control, Clutch, Idler Side by side or single Roller Tube of extruded

Aluminium 38mm inner dia - 41mm outer dia minimum wall thickness of

1.6mm. Roller blind - roller blind fabric should be made up of 35%

FibreGlass, 65% PVC, it should have specific low emissivity treatment and

lead free with Greenguard gold certification. It should have 3% to 5%

9 STORAGE UNIT WITH LAMINATE FINISH

Providing and Making of Storages (AS PER DRAWINGS) using ply of brand 15.00 Sq. Mt 11307.00

of brand greenply ecotech,mr mr conckreteply,archidply etc, (thickness

as specified)/ sag wood and finished by 1 mm Laminate outside, 1mm tk

laminate (inside), water pu polish (as shown), drawers, shelves etc. with

all hardware, handles, lock , magnet and other acessories with all

material, labour, lead and wastage etc. and complete the work

satisfactorily as per instruction of architect or Engineer-in charge.

10 KITCHEN DEDO ( 600 mm x 1200 mm )

Providing and laying tiles of 600x1200 mm size and 8 mm to 9 mm thick 13.49 Sq. Mt 2001.00

antiskid tiles on wall dedo laid on a bed of 30 mm thick cement mortar 1 :

3 (1 - cement : 3 -coarsed sand) finishing with 5mm Epoxy grouting of

brand laticrete,roff or kerakoll or flush pointing in white cement.and

complete the work satisfactorily as per instruction of architect or

Engineer-in charge.

11 BASIN DEDO ( 600mm x 1200 mm )

Providing and laying tiles of 600x1200 mm size and 8 mm to 9 mm thick 3.78 Sq. Mt 2001.00

antiskid tiles on wall and landing laid on a bed of 30 mm thick cement

mortar 1 : 3 (1 - cement : 3 -coarsed sand) finishing with 5mm Epoxy

grouting of brand laticrete,roff or kerakoll or flush pointing in white

cement.and complete the work satisfactorily as per instruction of

architect or Engineer-in charge.

12 WASH BASIN WITH HALF PEDESTAL

Providing and fixing WASH BASIN WITH HALF PEDESTAL (ECS-WHT-813, 1.00 No. 3115.00

ECS-WHT-813) of brand Essco by Jaquar with single hole for pillar tap

with C.I. or M.S. brackets painted white, including cutting holes and

making good the same but including fittings like pillar tap, brass waste,

stopcock, bottle trap and M.I.fisher union fittings of jaquar make or

equivalent make A) vitreous china: II. Flat back washbasin 460 mm x

mm x 160 mm size (I) IN white colour Providing and fixing M.I. Fisher

union for washbasin or sink A)32mmDia including all necessary fittings.

Providing and fixing ANGLE VALVE (MQT-526NKN) of brand Essco by 1.00 No. 946.00

Jaquar approved quality including fixing in pipe line etc. complete.

Providing & fixing WASH BASIN SPOUTS (PILLAR COCK) (MQT-508KN) of 1.00 NO. 2588.00

brand Essco by jaquar Heavy duty with hook with fitting including all

material, ,labour,and hardwares, transport,waste of materials,etc and

complete the work satisfactorily as per instruction of architect or

Engineer-in charge.

15 "L" TYPE TABLE FOR BILLING & SERVICE COUNTER WITH SIDE STORAGE

Providing and fixing of L-TYPE BILLING & SERVICE COUNTER WITH SIDE 1.00 NO. 100000.00

STORAGE table of size(4.15 X 0.65,3.00 x 0.65) mt and side storage of

width 1.00 mt,with granite top, as per drawings and instructions

provided,using ply of brand greenply ecotech,mr conckreteply,archidply

etc,or aluminium pipe for framing and finishing it with Granite top and

1mm laminate of brand greenlam or selected by the architect(basic rate

of unicore laminate is 3000 per sheet and other 1mm laminate is

per sheet, of size 8'0 x 4'0) ,as per drawing make side storage under

platform. 3 mmx 3mm groove (if shown) with all materials,polish

work,beading patti, labour, lead and wastage,m.s fabrication work with

80 microns powder coatings of selected shade, nylon leg levelers etc.

complete. And Finished with different materials,and complete the work

satisfactorily as per instruction of architect or Engineer-in charge.

16 LOW BACK CHAIR

Providing and fixing of Low back Billing counter chair of aluminium dia 1.00 No. 5000.00

cast base and armrest,50 density high mould foam in seat and back, multi

funtional mechenism, bifma class IV gas lift and p.a castors. Liven HB

Chair, Backrest and headrest shell finish in high gloss black, Headrest

height can be adjusted, Armrest pad finish in polish finish, Armrest height

and width can be adjusted, backrest and seat cushion in single-stitched

semi-aniline artificial leather, Seat shell finish in high gloss black, Seat

depth and height of sitting can be adjusted, Mechanism cover in silver

smooth powder coating. as per selection and complete the work

satisfactorily as per instruction of architect or Engineer-in charge.Basic

rate of chair is 20500/- per chair BRANDS : BRISTOL, HAYWORTH,

17 FIXED CHAIR-CANTEEN

Providing and fixing of lowback chair, Beige frame in glassfilled nylon in 36.00 No. 3500.00

reinforced grey/black horizontal lines elastomer mesh, with adjustable

headrest, Seat front tilt with lock & seat slider, Tapered seat density

mould foam to make waterfall angle, Alluminium five prong base with

silent rubber castor, Adjustable side ways arms with additional side way

angle swith, multi locking tilting facility, wooden PVC patch at the back on

nylon/PVC of size 6" x 9" for show purpose.as per selection and complete

the work satisfactorily as per instruction of architect or Engineer-in

charge.Basic rate of chair is 5500/- per chair. BRANDS : COHUMAN,

18 CANTEEN TABLE

18 Providing and fixing of canteen table of size 1.20 x 1.20 mt as per 9.00 No. 18000.00

drawings and central ss suport & granite top . all materials,polish work,

labour, lead and wastage,m.s fabrication work with 80 microns powder

coatings of selected shade, nylon leg levelers etc. complete. And Finished

with different materials,and complete the work satisfactorily as per

instruction of architect or Engineer-in charge.

19 PAINTING - 24"X24"

Providing and fixing of painting as per selection and complete the work 8.00 No. 2750.00

satisfactorily as per instruction of architect or Engineer-in charge.Basic

rate of chair is 2200/- per painting

20 PLANTER WITH REAL PLANTS

Providing and fixing of planter/pots of frp or plastic with real indoor 4.00 No. 3000.00

plants as per selection and complete the work satisfactorily as per

instruction of architect or Engineer-in charge.

21 PLANTER WITH ARTIFICIAL PLANTS

Providing and fixing of planter/pots of frp or plastic with artificial indoor 4.00 No. 3500.00

plants as per selection and complete the work satisfactorily as per

instruction of architect or Engineer-in charge.

Providing and fixing of wallclocks as per selection and complete the work 1.00 No. 1500.00

satisfactorily as per instruction of architect or Engineer-in charge.

23 OUTDOOR FLOOR MAT

Providing and fixing outdoor floor matt as per selection and complete the 1.00 No. 2500.00

work satisfactorily as per instruction of architect or Engineer-in charge.

24 INDOOR FLOOR MAT

Providing and fixing indoor floor matt as per selection and complete the 1.00 No. 450.00

work satisfactorily as per instruction of architect or Engineer-in charge.

Providing & Supplying of SS Dustbin ,having size of 8 In. Diameter & 12" 2.00 No. 450.00

Height etc. complete as per selection & directed by the Architect and

approved by the Engineer in Charge.

26 FULL BRICK WORK

Brick work using common burnt clay building bricks having crushing 13.29 CU.MT 4458.46

strength not less than 35 kg./Sq.Cm. in foundation and plinth in Cement

Mortar 1:6 (1- Cement : 6 -fine sand)(B)Conventional

27 10MM PLASTER

"Providing 10mm thick cement plaster in single coat on ceilings and 115.60 SQMT 175.47

sofits of stairs and finished even and smooth in (ii) Cement mortar 1:4 (1-

cement :4-sand) For Ceiling"

Providing and laying cement concrete 1:2:4 (1-Cement :2-Coarse sand :4- 7.00 CU.MT 3646.87

graded stone aggregates 20 mm nominal size) and curing complete

excluding cost of formwork in (A) Foundation and Plinth

Providing and fixing Concrete paver blocks in rustic design finish with 70.00 SQMT 972.98

70mm thick of orange Color with UV resistant color pigments from

lanxess. It shall be wearing resistant color coordinated aggregates. The

top surface shall be satin finish, water and oil repellence, reduction of

algae, moss and resistant to efflorescence formation. The grade of

concrete shall be M-400 pneumatic compressed by mechanically

vibropressed and as per approved by Engineer-In-Charge or Architect’s

design, including 40 mm sand/gravel/stone dust/ pana layer for levelling

and filling the joint with sand in proper line and level etc. complete. The

Paver shall have the following Properties.

1. Nominal Plan Size (mm)/Tolerance A 110*110, B 140*110, C 165*

2. Thickness /Tolerance- 70mm (± 2mm)

3. Pieces per Square Meter 55 nos.

4. Percentage Water Absorption Average not over 4.5% of its weight

5. Pieces per Module (Ratio) A 4nos., B 8nos., C 12nos., D 8nos., E 4nos.,

6. Compressive strength Average not less than 400 Kg/cm2

7. Tensile Splitting Strength (as per EN 1338) Average not less than

8. Average wear in Thickness- Abrasion Conforming to Grade ‘H’ of EN

9. Thickness of wearing layer Not less than 5mm

10. Colors Color blended- As specified by Architects. UV Light resistant

fast colors from Lanxess only to be used

11. Sealant Two coats of Acrylic Coat- Solvent free

Providing and fixing pre-cast concrete kerb stone of gray cement based 50.00 RU.MT 373.28

concrete block 30cm length,30cm height and 15cm thick of M200 grade

concret as per approved design and including excavation for fixing in

proper line and level,filling the joint with C:M 1:3 (1cement:3fine sand)

31 FABRICATION WORK FOR SHADE

Providing, fabricating, supplying and erecting structural steel framework 75.00 SQMT 3850.00

and Galvalume roofing work for industrial shed / factory / parking /

commercial building, including design, cutting, drilling, welding, bolting,

hoisting, alignment and erection of structural steel columns, rafters,

trusses, beams, bracings, purlins and all secondary members conforming

to IS 2062, complete with surface preparation and protective coating

(primer and paint or galvanizing as specified), and providing and fixing

Galvalume roofing sheets of minimum AZ150 coating and approved

profile in 0.60 mm base metal thickness, fixed with self-drilling, self-

tapping screws with EPDM washers, including all side laps, end laps,

sealants, ridge caps, flashings, gutters, downpipes, insulation (if

specified), ventilators, accessories and finishing, complete in all respects

as per approved drawings, manufacturer’s recommendations and

relevant IS codes, including all materials, labour, tools, tackles,

transportation, scaffolding, safety measures and commissioning of the

Providing & Supplying of WALLPAPER as per selection of approved brand 49.00 SQMT 1000.00

selected by the architect and complete as per selection & directed by the

Architect and approved by the Engineer in Charge.

33 Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of 1.5 sq.mm 19.00 Pt. 449.45

(Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multi

strand copper wires up to 10 mtr length , in below type of pipe erected

with 6A Modular type switch / bell push & accessories and earth

continuity of following type, erected on PVC / Metallic/Wooden box,

34 Point wiring for Tissino / Modular secondary light point with 2-1.5 sq.mm 14.00 Pt. 132.31

& earth wire of 1.5 sq.mm (green) both are of ISI marked 1.1 KV grade

FRLS PVC insulated multi strand copper wires, in below type of pipe to

be erected complete with earth continuity and necessary connection

with primary light with accessories erected on Metal / PVC / wooden

35 Point wiring for FAN with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) 14.00 Pt. 638.32

both are of .ISI marked 1.1 KV Grade FRLS PVC insulated multi strand

copper wires up to 10 mtr length, in below type of pipe erected with 6A

Modular type switch and hum free EME step type electronic fan

regulator mounted and accessories with earth continuity of following

36 Point wiring for on board Looped Plug with 6A Modular type switch & 5 8.00 Pt. 257.55

pin socket erected on PVC / Metallic/Wooden box, single mounting base

frame covered with textured / metallic/white front plate modules

erected on / in wall / ceiling with following type accessories Cat. III

37 Providing following type of Modular Type Accessories mounted with PVC 6.00 Ea. 151.50

/ metallic/Wooden box, single mounting base frame covered with

textured / metallic/white front plate , modules erected with necessary

connections as per site situation directed by Engineer In charge. (1)One

No. SP 6 Amp. Cat.III

38 (2) One No 5 pin plug Cat.III 6.00 Ea. 151.50

39 (7) Blank Plate Single Cat.III 7.00 Ea. 25.25

40 (9) 16 Amp. SP one way switch Cat.III 3.00 Ea. 180.79

41 (10) 6/16Amp. Universal socket Cat.III 4.00 Ea. 199.98

42 (14) 16A Double Pole Modular MCB Switch Cat.III 1.00 Ea. 410.06

43 Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI 198.00 Mtr. 82.82

marked stranded Copper conductor wire in following type of pipe to be

erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper

conductor FRLS PVC insulated stranded wire of green colour for earth

continuity of following size (A) With medium class Rigid PVC pipe and

accessories (b) 2 wire 2.5 sq. mm

44 providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI 24.00 Mtr. 112.11

marked stranded Copper conductor wire in following type of pipe to be

erected in / on wall / ceiling with 2.5 sq. mm copper conductor FRLS PVC

insulated stranded wire of green colour for earth continuity of following

size (A) with medium class Rigid PVC pipe and accessories (a) 2 wire 4 sq.

45 (h) 4 wire 6 sq. mm 46.00 Mtr. 260.58

46 Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt 3.00 Ea. 535.30

to 0.5 Watt assembled on single MCPCB, with housing used as a heat

sink shall be made of thick sheet Steel conforming to IS: 513/CRCA/

aluminium die cast powder coated and high U.V. & corrosion resistance

with diffuser with company mark/name 160V to 270V, Power Factor

47 Supplying and erecting led lamps with following wattage capacity of 220 1.00 Ea. 112.11

to 240 voltage, minimum 15000 burning hours life, 500 V in built-surge

protection,Polycarbonate diffuser, mounting suitable for E14 / E27 / B22

lamp holders, pf >= 0.5 (A) LED Lamps integral type, with PC diffuser

suitable LAMP holder (ii) 5 to 8 watts Cat-III

48 Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt 28.00 Ea. 758.51

to 0.5 Watt assembled on single MCPCB, with housing used as a heat

sink shall be made of thick sheet Steel conforming to IS:

513/CRCA/aluminium pressure die cast powder coated and high U.V. &

corrosion resistance with diffuser housed in aluminium casted body with

49 Supplying & erecting single phase approved make industrial exhaust fan 1.00 Ea. 2054.34

suitable for medium duty ring mounted low noise operation suitable for

medium duty having following dia size and maximum speed in RPM [A]

305 mm dia 900 RPM Cat.II

50 Providing & erecting Approved make Power Saving 50 Watt Ceiling Fan 14.00 Ea. 1948.29

with double ball bearing ISI mark with Condenser 230 volt A.C. 50 Hz

1200 mm sweep complete having 3blades with aluminium blades with

canopy & 30 cm. down rod erected with earthing.(Make shall be

approved by Engineer in charge))

51 Supplying and erecting 19 / 20 mm. nominal bore Medium Class M.S. 14.00 Mtr. 108.07

Pipe down rod erected duly painted for fan complete with proper

insulation without leakage and earthing.

52 Providing Fan clamp of 30 x 5 mm flat of required length & 10 mm M.S. 14.00 Ea. 98.98

Bolt & Nuts erected with necessary hook of 10 mm M.S. Round Bar.

53 Providing 2.5mm.thick laminated acrylic sheet to cover the fan hook or 14.00 Ea. 18.18

54 providing and erecting Miniature circuit breaker single pole 6A to 25A 12.00 Ea. 112.11

suitable to operate on 240 V A.C. system and having breaking capacity

KA to be erected in existing box. confirming to IS 8828/1996 with ISI Mark

55 providing and erecting Approved make RCCBs conforming to IS: 12640 3.00 Ea. 2235.13

and having sensitivity of 30 mA and Short Circuit withstand capacity of

KA and suitable for operation on single phase 240 V,50Hz. having

characteristic of quick action & tripping with all advance feature & do not

incorporate any electronic component. for following Max. rating erected

56 Providing & erecting 415V MCB Four Pole Switch for Lighting Load (B 2.00 Ea. 638.32

curve) having 10KA breaking capacity & confirms to IS :8828 in existing

box having following capacity (b)40 Amp. Cat.III

57 Providing and erecting Sheet Steel powder coated MCB distribution 1.00 Ea. 2339.16

board - flush / surface mounted fitted with busbar, neutral link, earth bar

and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to

house appropriate nos. of MCBs.(The DBs should be used of same

company of MCB to be used) suitable for (B) three phase incoming and

single phase horizontal type outgoing Per phase isolation type (PPI) (b)

sheet steel double door (i)4 way

58 Providing and erecting water cooler having storage capacity 80Ltr. & 1.00 Ea. 49559.69

cooling capacity 40 Ltr.per hour @ an ambient temp of 45˚ C. The outlet

temp. of the water should drop by 15˚ C within a hour, The water cooler

should be comprising of hermetically sealed compressor, fan motor,

condensing unit, water tank surrounded by evaporating coil, thermostats,

relay etc. complete with necessary inlet & outlet connection. The body of

water cooler will be made from Stainless Steel. ◦

59 Supplying & erecting 5 stage single reverse osmosis water purification 1.00 Ea 29187.99

system with M.S. powder coated frame, prefilter housing with 'O' ring

presediment filter GAC filter, carbon filter suitable buster DC pump

capacity 80 psi, mention with 40 psi inline type post carbon filter auto

low & high pressure switches with following size of storage tank & LPH

capacity & erected as directed [C] 50 Ltr / Hr with 150 psi 2 nos booster

60 Providing & Erecting Deep Freezers effective and economical Solutions 1.00 Ea 41770.57

for safe storage of perishable foods.The range of hard - top deep freezers

Technical Specification

Gross Capacity 400 ltr., Temp. Range -18°C to -22°C, Power Supply

230Volts, Single phase, 50Hz,Refrigerant R134A, No of lids 2,Inner

Cabinet Pre-painted GP Steel, Puf Thickness 60*60,Over all No of Baskets

01,Wheels/Legs Heavy Duty Castors.

Rupees Eighteen Lakh Seventy Five Thousand Four Hundred Thirty Seven And Seventy Eight Paisa Only.

I/We am /are willing to carry out the work at…………% above/below percent (should be written in figures and words) at the estimated rates

mentioned above amount of my/your tender works out as under.

*Estimated Amount *Estimated Amount

put to Tender Rs. 1875437.78 put to Tender Rs.

Deduction …………….. % below………………… Add ………… % above Rs. …………….

1 The Contractor shall be exhibit board as per government circular No.BDG/3277/1657 N dated 26/01/1997 S (M.GUJ) with detailed

specification and details of work and amount Involved at site without any payment as directed by Engineer-In-Charge.

2 All work shall be carried out as per public work department hand book and other specifications of Division or as directed.

3 All columns in the Schedule should be filled in ink & the total of the entries in the last column should be struck by Contractor under his sign.

4 Rates quoted include clearance of site (Prior commencement of work and its close) in all respects and hold good for work under all

condition, site, moisture/ weather etc.

5 The Boards stating the detailed specification & detailes of Work shal be provided by the contractor as per Government Resolution

T.No.1890-240- Dtd.18/11/1990 and directed by contractor at his own cost immediately on recommanding the work order.

6 Testing of Material Shall be done as per the statement attached with specification,The material IS Tested in GERI by Executive Engineer

Surat and Bill for the testing charges shall be paid by Executive Engineer,1% of the Amount put to Tender.

7 1% of the Construction Cost Shall be deducted from the bill Amount of the contract as per the Buildig and other Construction works walfare

cess at 1996(Labour and Employment Department Letter No CWA-2004-1831-M(3)Dated 9/12/2005 notification Of Labour & Employment

department dt.03/01/2005 & Labou & Employment Department Letter no GWA/2004-841M(B) Dt 14/12/2005 & Dt.30/1/2006.

8 In Case of RCC items Where there is a change in Grade of Mix or Change as per Actual Mix design the cost of difference of Cement

Difference shall be deducted from the rate of original item at the rate of star rate mentioned in the tender.

9 Contractor are advised to visit site before loading tender rate.

10 Necessary wiring point and drainage point are installed at Site however any modification in electrical installation and drainage & water

supply connection and minor correction to perform experienced in Lab shall be done by contractor at his risk and cost.

11 The Rates are inclusive of all the taxes (Excluding GST),Transport Charges,Octroi duty and storage Charges up to date.

12 The materials Covered for wiring should be got approved from the Engineer Incharge of the work.

13 GST and Income tax TDS will be deducted at a source while making payments of bills.

14 GST will be paid extra as per Govt. amendment.

15 The Materials on the work shall have to be used and carried out as specified in technical note.

I/We hereby Declare that I/we have Visited the site and fully Exquisite myself/ourselves with the local situation regarding materials,Labour

and other factors pertaininfg to work before submitting tender.

I/We hereby Declare that I/we have carefully Studied the condition of Contracts,Detailed Specification and other tender Document of this

work and agree to execute the same accordingly.

Deputy Executive Engineer

Valsad (R&B) Sub-Division

Signature of Bidder

Executive Engineer

Valsad (R&B) Division