NIQ-15- (EL) of 2026-2027 (SL NO 02)

SITC of PV Module : Monocrystalline of not less than 200 Wp PV Module with efficiency > 19% under STC equivalent MNRE / SEC Tested/ALMM approved - 200Wp Make – Waree / Vikram Solar/Adani/Neosole/ Green Brillions, Sun2Earth, Ib Solar/Kon Son/Panasonic or equivalent as per the choice of the EIC (Total Wp>= 800 W with 2/4 panels) i) Indigenously manufactured PV module with DCR (Domestic Content Requirement) compliance should be used. ii) The PV module should have crystalline Silicon Solar Cells and must have a certificate of testing conforming to IEC 61215 Edition II / BIS 14286 from an NABL of IECQ accredited Laboratory. iii) The power output of the modules under STC should be minimum of 200 Wp at load voltage of 32.8+_0.2 V iv) The open circuit voltage of PV modules under STC should be at least 21.0 Volts. v) The module efficiency should be more than 19%. vii) The PV modules must be warranted for their output peak watt capacity, which should not be less than 90% at the end of Ten(10) years and 80% at the end of Twenty five (25) Years. viii) IP 66 rating .Submission of test reports and warranty certificate for atleast five years from OEM is mandatory.

SITC of 12.8V 100 AH Lithium Ferro Phosphate (Li-FePo4) Rechargeable- BIS Certified Cells- Make- Bodhi / Future-Tech / Ensol/Microteck/Litpax / Lekrant / Bradpower or Equivalent BIS as per the choice of EIC i) 12.8V 100 AH Lithium Ferro Phosphate. ii) Battery should conform to the latest BIS/International standards. iii) Electronics should operate at 12.8 V and should have temperature compensation for proper charging of the battery throughout the year. iv) The Luminaires housing should be water proof (IP 65) and should be painted with a corrosion resistant and should be housing the battery. v) MPPT charge controller with >925 efficiency. Submission of test reports and warranty certificate for atleast five years from OEM is mandatory.

SITC of Flood Light Luminaire -60Watt -WLED Based Model No. : LED SOLAR 09SFL 60W200Wp60AHLIFEPO4WOPCWLRMS Make: Halonix or Model No. BVP483 LED150 CW Solar Make Philips/ Model No.SOLFE60 x 4WL2P Make Solarize/ Model No.SSLE SFL 60W Make Surya or equivalent model of Transrail/Osram/Orient Electric/Bajaj/Panasonic as per the approval of E-I-C. i) W-LED luminaire, dispersed beam, soothing to eyes with the use of proper optics and diffuser . The light source will be a white LED type ii) The luminous performance of LEDs used should not be less than 160 lumen/watt. iii) W-LEDs should not emit ultraviolet lightiv) The colour temperature of W-LEDs used in system should be in the range of 5500 ok - 6500 ok. v) Multiple light levels : The lamp should have two levels of light to take care of different lighting needs during the night. vi) 1.5 Sq mm 2 Core cable as per ISI standard to connect between charge controller and SPV module vii) MPPT Charge controller with efficiency > 92%. viii) Duty Cycle :Programmable dimming with minimum 1.5 days autonomy. First six hours full light 100% intensity, next four hours with 80 % intensity and rest of the time of two hours with 50 % at lower light level with fix dimming. ix) OEM Manufacturer must have in-house NABL accredited test lab for LM79 and IS10322 type test testing facility. x) OEM manufacturer need to provide assurance for integration of Battery pack within housing and integration & functionality operation as per requirements.xi) Rating IP 66 xii) LED Chips should be made of Osram/Nichia/Cree/Seoul semiconductor only, with lenses for effective light distribution. Complete system and BMS should provide 1.5days (36 hours) back up in dimming mode using PIR sensor.

SITC of Galvanized Solar Mast shaft shall be in 2 sections with PV Module Mounting Structure and Other accessories ( Make Transrail/Signify/Halonix/Solarize/Surya/Bajaj/Orient Electric as per the choice of EIC) i) Pole Height : 10.5 Mtr ii) Pole Outer Dia : Bottom Dia 410 mm & Top Dia 150mm iii) Thickness : > 4 mm Base Plate-570mm; PCD-490mm iv) 4-Sided Header with 8mm SS Rope v) Earthing Strip Details: 50mm X 6mm Earthing Pipe (Pipe in Pipe Model) with Chemical Backfill , Compound Display Board with MS Sheet of size 3ft X 2 ft with pole mounting arrangement with the following printed matter"N.B.D.D Date of Installation-, DLP Period -, Contact Persons for maintenance (from agency and OEM service team)".vi) Foundation I-Bolt M30 x850 mm 6.8 Grade (TS 600) with anchor & Template Plate vii) Manual operation power tools with 350-500 Kg SGDD as per design viii) Suitable steel structure arrangement for 4 no.s Solar Panel and fixing of Solar LED Luminaries ix) Double ring type for 4 Nos luminaries & 4 Nos solar Panel structure x) Compulsory gear mechanism by hand pulley for lifting and lowering of the Solar PV panels for cleaning and maintenance service. xi) The mast must sustain the minimum wind speed of 180 km/hr. xii) OEM must submit structural wind load certificate of above items of 180 km/hr wind speed with a minimum speed of above iems of 180 km/hr. Submission of test reports and warranty certificate for atleast five years from OEM is mandatory.

Remote monitoring for 5 years: Provision for remote monitoring for the pumps must be made in the system with an inbuilt Remote Monitoring System, integrated with MPPT charge controller and it would record the parameters at a fixed interval of 10 Minutes, Recorded data should be available in the PDF, XLS, JPED, PNG & SVG Format with the Data logging of the following parameters 1. Battery: Voltage/Current/Power 2. Solar PV Module: Voltage/Current/Power 3. Load: ON-Off Status/Voltage/Current/Power 4. Fault description 5. Site Co-ordinates 6. Controller must have a back up to store the data locally (at least for 1 years) supply |& installation of GSM/GPRS based Data Transmitter or Modem and to provide remote monitoring service to transmit the parameters to central server from the solar pumping system with time stamp at user-defined interval and report generation at the buyer end. (Refer Technical Spec.)

Earthing with G.I. earth pipe 4.5 Meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

RCC Foundation and Erection of Solar High Mast of 10 Mtr length in cement concrete 1:2:2 M25 Grade (1 cement: 2 coarses and: 2graded stone aggregate 40 mm nominal size) foundation including excavation and refilling etc. as required Foundation size Column: 575mm x 575mm and Height from base : 1800 mm. Footing :1800mm x 1800mm.

The periodically check up and servicing cost @ 10% of sum of the item no (01) to (07) for each Solar High Mast. The entire system should be in working condition properly during the entire defective liability period. This cost includes the necessary cleaning, check up, replacement of spare parts and necessary adjustment during the whole D.L.P through OEM. The OEM must provide technicians atleast two for monthly inspection, cleaning and maintenance of Solar Panels, battery etc. atleast 8 times a year for each high mast for each of the five years of warranty period and a log book of attendance of the visiting technicians in the letter pad of OEM/ authorised service provider of OEM duly signed by the authority whom the handover will be made, concerned Sub Assistant Engineer and concerned Assistant Engineer. Submission of test reports and warranty certificate for atleast five years from OEM is mandatory. A declaration of notarized warranty of Solar High Mast for five (5) years from an OEM shall have to be submitted by the bidder through an AFFIDAVIT on Govt. Stamp Papers mandatory.