Construction Assistant District Attorney Office Building Bassa at Gohar Tehsil Chachiot Distt Mandi HP SH Construction of Building Portion including W S and S I

Amount

Excavation in foundation trenches etc. in earth work, in earth work, lift upto 1.50 (One point fifty )metres stacking the eacavated soil not more than 3 (Three) metres clear froom the edge of the excavation and then returning the stacked soil in 15 cm (Fifteen centimetre), layers, when required into plinths sides of foundation etc. consolidating each deposited layer by ramming and watering and the disposing of all surplus excavated earth as directed with in a lead of 20 (Twenty)metres, pick work and jumper work as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing and laying cement concrete 1:3:6 (one cement:three sand: six graded stone aggregate 40 mm (forty milimetre) nominal size) and curing complete exluding cost of centring and shuttering in foundation and plinth as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing and laying cement concrete 1:4:8 (one cement :four sand :eight graded stone aggregate 40mm nominal size)( Forty milimetre size) mechanically mixed and vibrated and curing complete excluding cost of form work in foundation and plinth as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing and laying cement concrete 1:5;10 ( one cement : five sand : ten graded stone aggregate 40mm.(Forty millimetre) mechanically mixed and curing complete excluding the cost of form work in foundation and plinth as per direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing form work with steel plates 3.15mm(Three point fifteen millimeter) thick welded with angle iron in frame 30x30x5mm(Thirty millimeter into thirty millimeter into five millimeter) so as to give a fair finish including centering, shuttering, strutting and propping etc. with wooden battens and ballies in any height of propping and centering below supporting floor to ceiling upto floor all level and removal of the same for in situ-reinforced concrete and pain concrete work including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge in:-

Foundation, footing basis of columns etc. and mass concrete .

Flat surfaces such as soffits of suspended floors, roofs, landings and the like Floors etc upto any thickness.

Beams, cantilever, girders and lintels sides and soffits of beams, beam hunching, cantilevers, bressumers and lintels in any depth in all height from floor.

Columns, pillars, Posts and struts, Square, rectangular or polygonal in plan.

Stair cases with sloping or stepped soffits excluding landing.

Vertical surface such as walls(any thickness) and the like including attached pilasters, buttersses plinth and string courses and the like.

Providing and laying damp proof course 38 mm (thirty eight millimetre) thick with cement concrete 1:2:4 (one cement :two sand :four stone aggregate 12.5 mm (twelve point five millimetre) nominal size) and curing complete as per direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Applying a coat of hot bitumen (mexphalt 80/100 (eighty/hundred) or equivalent) using 1.70 Kg. (one point seven zero kilo gram) per square meter on damp proof course after cleaning the surface with a piece of cloth lightly soaked with kerosene oil as per direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing and laying M-20 grade cement concrete with mechanically mixed and vibrated with minimum cement contents as 300 kg (Three hundred kilo gram). per cubic meter with curshed stone aggregate 20mm (twenty milimetre) nominal size and curing complete excluding cost of form work including mechanically mixer and vibrating work in as per directionof Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Suspended floor roofs, landing and shelves and their suport balconies, beams girders, bressumers and cantilever upto floor two level

Wall (any thickness but not less than 0.10 m (Zero point ten) thickness) attached pilasters, buttresses, plinth and string courses etc. from top of foundation level upto floor two level

Providing and laying cement concrete M-25 1:1.5:3 (one cement : one point five Sand : three graded stone aggregate 20 mm (Twenty milimetre) nominal size) mechanically mixed and vibrated and curing complete excluding cost of form work. and reinforcement for reinforced cement concrete work as per Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Foundation, footing basis of columns etc. and mass concrete .

Suspended floors, roofs ,landings and shelves and their support, balconies, beams, girders, breasumers and cantilevers up to floor all level.

Walls (any thickness but not less then 0.10 (Zero point ten) meter thickness) including attached pilasters, buttresses, plinth and string courses etc. from top of foundation upto all floor level.

Columns, pillars posts and struts square rectangular polygonal in plain upto floor all level.upto floor two level.

Stair cases (except spiral stair cases) excluding landing but including preparing of the top surface and finishing of nosing upto floor all level.

Providing and laying upto all level reinforced cement concrete 1:2:4 (one cement : two Sand :four graded stone aggregate 20mm (Twenty milimetre) nominal size) mechanically mixed and vibrated to give an smooth and even surface including centring and shuttering etc. but excluding cost of reinforcement in String courses, copings, bed plates, anchor blocks, plain windows sills and the like as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Upto Floor to Level.

Providing Tor steel reinforcement for R.C.C. work including bending, binding and placing in position complete including cost of binding wire up to any level as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Brick work using common burnt clay building brick in foundation and plinth in mud mortar 2nd class brick as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Brick work using common burnt clay building bricks in super structure in cement mortar 1:6 (one cement : six sand) 2nd class brick as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. Up to floor all level.

Half brick masonry in common burnt clay building bricks in super structure in cement mortar 1:4 (one cement : four sand) 2nd class brick as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals (i) above plinth level upto floor all level.

Squared rubble masonry coursed with hard stone of approved quality in foundation and plinth including racking out joits in cement mortar 1:5 (One cement:Five sand).as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Random rubble masonry/polygonal rubble masonary (uncorsed/brought to cources) with hard stone of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (one cement : six sand : twelve graded stone aggregate) 20mm (Twenty milimetre)nominal size) at plinth level in cement mortar 1:6 (one cement: six sand). as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing anodized aluminum tower bolts (barrel type ) anodized trans parent or dyed to equired shade and colour with screws etc. complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

200x10mm (Two hundred x ten millimeter)

150x10mm (One hundred fifty x ten millimeter)

100x10mm (One hundred x ten millimeter)

Providing and fixing aluminium handles anodized transparent or dyed to required colour & shade with necessary screws etc. complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

125 mm (One hundred x twenty five millimeter)

100 mm (One hundred millimeter)

75 mm (seventy five millimeter)

Providing and fixing 100mm (One hundred millimeter) bright finished brass floor door stopper with rubber cushion screws etc. to suit shutter thickness complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing anodized aluminium sliding door bolt anodized colour and shade with bolts and nuts screws etc. complete.300x16mm (three hundred x sixteen millimetre) as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing and fixing 19mm thick ( ninteen milimetre) thick terramite resistant water proof commercial board box including shelves and shutters, the back side of cupboard/cabinet of 8mm(Eight milimetre) thick ply and cut portions of shelves shall be finished with 6mm six milimetres) hard board edging. The cut portion of shutters from all the sides shall be finished with 12 mm (Twelve milimetre)thick hard wood edging. the shutters from out side shall be finished with 1mm thick laminated of approved shade includng piano hinges and magnetic catcher with all ascessories as per detail architectural drawing No. 195/1 to 199/1 including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying 10 mm (Ten milimetre) thick full body vetrified tiles in matte finish of Asian/Johnson/Kajaria or equivalant 600x600mmx10mm (six hundred milimetre into six milimetre into ten milimetre)manufactured of approved shade and colour in flooring, treads of steps and landing laid over 12mm (twelve milimetre)thick cement mortar 1:3 (one cement : three sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete. as per directionof Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Upto Floor all Level

Providing and fixing 10mm (Ten milimetre) thick full body vitrified tiles in matt finish of size 600x600 mm (six hundred milimetre into six milimetre) approved shade and colour in Skirting 10mm(Ten milimetre) (average)thickness base of cement 12mm(twelve milimetre) mortar 1:3(one cement: three sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone including rubbing and polishing complete as per directionof Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Upto Floor all Level

Kota stone slab flooring 20 mm (twenty five milimetre)(average) thick base of cement mortor 1:4 (one cement :four sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab. Including rubbing and polishing complete as per directionof Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. 25 mm (twenty five milimetre).( Upto floor all level)

Kota stone slab 25 mm (twenty five milimetre)thick in risers of steps,skirting dado and pillars laid on 12 mm (twelve milimetre)(average) thick cement mortar 1:3 (one cement : three sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs including rubbing and polishing complete as per directionof Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.(ii) Upto floor two any level.

Providing and laying granite stone in flooring 19 mm (Nineteen milimetre)thickness base of cement mortar 1:3(one cement: three sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone i/c rubbing and polishing complete as per directionof Engineer-in Charge including carriage of materials with in all leads, lifts and other incidentals.

Upto Floor all Level

Providing and laying 10mm digital ceramic tile of size 300 x 600 mm (three hundred into six hundred milimetre) in skirting risers of steps and dados of approved shade and colour laid over 12mm (twelve milimetre)thick cement mortar 1:3 (one cement : three sand) jointed with cement slurry mixed with pigment to match the shade of tiles . as per directionof Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Upto Floor all Level

Providing and fixing 12mm (twelve milimetre)thick Glass Reinforced concrete cladding of approved shape and texture of unistone or its equivalent made from portland cement alkally resistance glass fibres, UV resistant synthetic inoraganic pigment combined with the range of chemical additives on exterior surface side as on faces of Arch masonry walls etc. 12mm (twelve milimetre). thick cement plaster 1:3(one cement: three sand) and jointed with cement slurry i/c scaffolding etc as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Upto Floor all Level

Providing and laying red sand stone slab in treads and rises of steps on a bed of 20mm (twenty milimetre) thick cement mortar 1:4(one cement :Four sand)laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including preparing of nosing rubbing and grsnite polish finish complete and as per direction of specification and as per direction of Engineer-in-Charge including carriage of materials with in all leads,lifts and other incidentials.

Providing and fixing on wall face 100mm (One hundred milimetre) dia PVC(D-Plast) rain water pipes of working pressure not less than 4.5 Kg /sqm(Four point five kilogram per square metre) including filing the joint with approved adhersive complete as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing on wall face (D-Plast) accessories for rain water pipes including filling the joint with approved adhesive complete as per the direction of Engineer-in-Charge of materials within all leads, lifts and other incidentals.

PVC Plain Bend 100mm(One hundred milimetre) dia.

Shoe 100mm dia(One hundred milimetre) dia.

Providing and fixing 0.60mm (Zero point six zero milimetre) thick preprinterd steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyester (RNP) organic coating of 20 (Twenty) microns over 5 ( five) micons primer coating to back coast of polyester of 5 (five) microns over 5 (five)microns primer coating including fixing with screws, prepainted iron J or L hooks, bolts and nuts 6mm(six milimetre) dia with prepainted limpet and rubber washer complete with all accessories as required as per specifications and as per direction of Engineer-in-Charge including carriage of materials with in all leads, liftsother incidentals.

Providing and fixing M.S. BP Sheet 1.66 mm(One point sixty six milimetre) to 2mm (Two milimetre) thick in eves board/ facia/soffit/ceiling including cutting ,fixing and welding to steel roof members and applying a coat of red lead primer complete as per direction of the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Steel work welded in built up sections, trusses and framed work,including cutting, hoisting fixing in positiobn and applying a priming coat of red lead paint as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals in:

Gratings framed guard bars laddeds railing brackets and similar works including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 65mm x 75mm(sixty five milimetre) into seventy five milimetre) hand rails in 1st class Indian teak wood straight length complete as per the direction of Engineer-in-Charge including carriage of materials within all leads, lift and other incidentals.

6mm (Six millimeter) cement plaster to ceiling in cement mortar 1:3 (one Cement : three Sand) as per the directions of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

15mm (fifteen milimetre) cement plaster in single coat on the fair side of brick/concrete/stone walls for interior plastering upto floor to any level including arrises, internal rounded angles, chamfers and /or rounded anges not exceeding 80 mm (eighty milimetre)in girth and finished even and smooth in cement mortar 1:3 (one cement:three sand) as per directionof Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

15mm (fifteen milimetre) cement plaster in single coat on the rough side of brick/concrete/stone walls for interior plastering up to all floor level includingarises, internal rounded angles,chamfers and/or rounded angles not exceeding 80mm(eighty milimetre) in girth and finished even and smooth in cement mortar 1:6 (one cement:six sand)as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Upto Floor all Level

15mm (fifteen milimetre) cement plaster in single coat on the fair side of brick/concrete/stone wall for interior plastering upto floor all level including arises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm (Eighty milimetre) in girth and finished even and smooth in cement mortar 1:6 (one cement: six sand) as per the direction of Engineer-in-Charge including carriage of materials within all leads, and lifts other incidentals.

Upto Floor all Level

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Distempering (Two coats) with oil bound washable distemper of approved brand and manufacture of and of required shade of undecorated wall surface to give an even shade over and including a priming coat with alkali resistance primer of approved brand and manufacture after thoroughly brushing the surface free from mortar dropping and other foreign matter and also including preparing the surface even and sand papered smooth as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Wall painting (two coats) with plastic emulsion paint of approved brand and manufacture on undecorated wall surfaces to give an even shade i/c thoroughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth i/c applying of putty a required for making the surface as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Applying priming coat over new steel and other metal surfaces after and including preparing the surface by thoroughly cleaning oil grease dirt and other foreignmatter and scoured with wire brushes fine steel wool scrubers and sand paper complete with ready mixed priming pant brushing red leadred oxide/zinc oxide chrome as per the direction of Engineer-in-Charge including of materials within all leads,lifts and other incidentals.

Painting two coats (excluding priming coat) on new steel and other metal surfces surfaces with enamel paint brushing to give an even shade including cleaning the surface of all dirt, dust and other foregin matters Enamel paint other than white including carriage of materials with in all leads, lifts and other incidentals.

Applying priming coat over new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil, grease,dirt and other forein matter sand papering and knotting ready mixed paint with wood priming pink of approved brand and manufacture (Nerolac/Asian Shalimar) conforming to IS: 3536-1966 brushing as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Painting two coats (excluding priming coat) on new wood and wood based surfaces with ready mixed paint brushing to give an even shade including cleaning of oil, grease,dirt and and other foreign matter sand papering and stopingready mixed paint other thanwhite as per direction od Engineer-in-including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing bright finished brass 100mm.(One hundred millimeter) Mortice latch and lock and a pair of levers, handles with necessary screws etc. complete (indian make of approved quality) as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. .

P/F 12 mm (twelve milimetre) thick bwp prelaminated phenol bonded exterior/interior grade particle board in panalled shutters for frame of aluminium for doors including bright finished/black enamelled iron butt hinges with necessary screws. complete as per specification and as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing and fixing glazed with glass panes of 5.50mm (five point five zero milimetre) thickness (weight not less than 13.75 kg/sqm) (thirteen point seventy five kilogram per square metre) as per direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing anodised aluminium work for door, window, ventilators and partitions with extruded built up standard tubular and other sections of approved make conforming to IS 733 and IS 1285 anodised transparent or dyed to required shade according to IS 1868. (Minimum anodic coating of grade AC 15) fixed with rawlplugs and screws or with fixing clips, or with expansion hold fastners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rustfree, straight, mitred and jointed mechanically where ever required including cleast angle, aluminium, snap beading for glazinge/panelling C.P. brass/stainless steel screws. As per directionof Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

For doors windows and ventilatiors and glazed partitions frames.

For shutters of doors windows & ventilators

Providing and fixing grill of aluminium anodised powder coated grill of required pattern to existing window/ventilatior with 80mmx80mm (eighty milimetre into eighty milimetre)panels holes with 25x8mm (twenty five into eight milimetre )thick aluminium flat in windows and ventilators including fixing with aluminium screws or bolts and nuts complete in alluminium channels base frames (Aluminium channels base frames to be measured and paid for separately) as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals ..

Providing and fixing Aluminium sheet 4 mm (four milimetre)thick composite panel having core of polythene fixed to internal side with screws or nails as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing and fixing fibre board ceiling tiles of size 600 x 600 mm (six hundred milimetre into sixhundred milimetre) over ready made powder coated metal sheet section frame work 600 mm (six hundred milimetre) c/c grid susepended from ceiling of complex with butterfly clips and hinges etc as required pattren complete in all respect as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing bright finished hard drawn hooks and eyes as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.200mm(Two hundred millimeter)

Providing and fixing 115mm (one hundred fifteen millimeter) bright finished brass hasps and stapples (safety type) with necessary screws etc complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 150mm (one hundred fifty millimeter) oxidized M.S. single acting spring hinges with necessary screws etc. complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing double action hydraulic floor spring of approved brand and manufacture (conforming to IS 6315) for aluminium door including cost of cutting floor as required embedding in floors and cover plates etc. complete as per the direction of Engineer-In-Chargeincluding carriage of materials with in all leads lifts and other incidentals.

Providing and laying heavy duty precast cement conrete inter locking paver blocks vibro compacted upto M- 50 grade i/c border or kurb block grey or coloured over sub-base of concrete with 25mm( twenty five millimeter) thick average thickness of cement mortar 1:4 (1 cement : 4 sand) laid over and jointed with neat cement slurry mixed with pigment to match the shade of blocks i/c curing rubbing & polishing complete. 60mm thick interlocking blocks.

Providing under layer for plinth protection of 75mm (Seventy Five millimetre) thick (unconsolidated) bed dry brick/stone aggregated 40mm (Forty millimetre) nominal size well rammed and consolidated and grouted with fine sand including preparation of ground as per direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Constructing course rubble dressed "U" shape open surface drain with side wall 15X22cm (fifteen into twenty two centimetre) in cement mortor 1:6 (one cement: six sand) and in side plstring with cement plaster 1:3 (one cement : three sand ) including earth work and laying 10cm (Ten Centimetre) cement concrete 1:5:10 (one cement :five sand:ten graded stone aggregate 40mm (Forty millimetre) nominal size) and 7.5cm (seven point five cenimetre)cement concrete 1:2:4(one cement :two sand ;four graded stone aggregate 20mm (Twenty millimetre) nominal size) and finishing with a floating coat of neat cement and curing complete as per standard design as per the entire satisfaction and direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Filling with brick aggrigate in soak pit complete as per direction of Engineer-in-Charge.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Boulder filling dry hand packed tightly as in wire crete apron bund wire cretes to be measured separately (under floor ) (wire crete to be measure )as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Applying cement slurry on RCC slab or cement concrete work using 2.75 Kg. (two point seventy five kilogram) of cement per square metre of floor area before laying cement concrete flooring including roughening, cleaning of the concrete surface complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals .

Excavation in drain and channels etc. in earth work in all kinds of soils such as pick work, jumper work, pick jumper work , pick jumper blasting work , blasting work in soil and hard rock conglomerate rock or saturated soil and its intermediate classification of soil including chiseling/wedging out of rocks (where blasting is prohibited) and pumping or bailing watering/dewatering including dressing of sides and bed and disposing of excavated earth upto any leads and lifts disposted earth to be leveled and neatly dressed as directed by the Engineer-in charge within any leads including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing to wall ceiling and floor galvanized mild steel tubes (Medium grade) tube fitting and clamps including making good the wall, ceiling and floors as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

15mm (fifteen millimetre) nominal bore

25 mm (Twenty Five Millimetre) nominal bore

Providing and fixing to wall and ceiling and floor Polythene Aluminium composite pressure pipe of 15mm (fifteen milimetre)dia of Kitec confirming to ISI 15450-2004 including making good the wall, ceiling and flooras per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying in trenches, galvanized mild steel tubes (medium grade), tube fittings (earth work in trenches to be measured and paid separately) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

25 mm (Twenty Five Millimetre) nominal bore

Making connection of galvanized steel distribution branch with galvanized mild steel main 20mm(Twenty Millimetre) to 40mm (Forty Millimetre) nominal size bore by providing and fixing tee including cutting and threading the pipes complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Construction chamber 300mm x 300mmx500mm (three hundred x three hundred x five hundred millimetre) inside size for stop cock with C.I. surface box 100mm x 100 mm x 75mm (One Hundred x One hundred x Seventy Five millimetre) (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (one cement : two sand :four graded stone aggregate 20mm (Twenty millimetre) nominal size) 75mm (Seventy Five millimetre) thick foundation concrete 1:5:10 ( one cement : five sand : ten grades stone aggregate 40 mm (Forty millimetre) nominal size) and inside plastering with cement mortar 1:3 (one cement :three sand) finished with a floating coat of neat cement including curing complete with 100 mm (Hundred millimetre) thick walls of brick masonry in cement mortar 1:5 (one cement: five sand) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing vitreous China wash down, water closet European type. W.C. pan No 200049 in white shade with integral 'P' or 'S' trap including jointing the trap with soil pipe in cement mortar 1:1 (one cement : one sand) of Parryware/Hindware/Jaguar or its equivalent as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing white plastic seat and cover for wash down water closet with C.P. Brass hinges and rubber buffers of Parryware/Hindware/Jaguar complete as per the direction of Engineer in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing vitreous China wash down, water closet Orissa Pattern No.200004 squatting pan (Indian type W.C pan) size 580mm x 440 mm(five hundred eighty milimetre into four hundred forty milimertre) (Earth work, bed concrete, foot rest and trap to be measured and paid for separately) of Parryware/Hindware/Jaguar as per the direction of Engineer in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing PTMT White colour high density polyethylene / poly propylene 10(ten) litres capacity ( full flush) European standard control low level flushing cistern No. 2602 of Parryware/Hindware/Jaguar with fittings with a pair of brackets with fittings such a lead valve, syphon, 15mm (fifteen milimetre)nominal size PVC ball valve with polythene float, with push button, couplings for connections with inlet, outlet and over flow pipe, 40mm dia C.P. flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (overflow pipe to be measured and paid for separately) .as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 110 mm (one hundred ten milimetre)dia PVC ‘P’ or 'S' trap for water closet (squatting pan) ISI marked including jointing the trap with the pan and PVC pipe with approved adhesive etc. complete.as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing PTMT jet spray of Cera/Hindware/jaguar with 1.5 mtr. (one point five metre)Tube complete.as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing vitreous China wash basin with single hole for pillar tap with cast iron or mild steel brackets painted white including cutting holes and making good the same but excluding fittings flat back:-(i) 550mmx400mm (five hundred fifty into four hundred millimetre) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing vitreous China pedestal for wash basin complete recessed at the back for the reception of pipes and fittings as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing stainless steel kitchen sink of size 610 x460 x 200 (six hundred ten into four hundred sixty into two hundred) No. 1022 of Paryag Polymers milimetre of approved standard ISI make with drain board and C.P. waste with C.I. or M.S. Brackets painted white including cutting holes and making good the same (but excluding fitting) of as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 32 mm (thirty two millimetre ) dia diametre C.P brass waste for wash basin or sink of approved brand and menufature as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing M.I. Union for wash basin or sink 32mm (thirty two millimetre ) dia size including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing 32 mm (thirty two millimetre ) dia C.P. Bottle Trap for wash basin or sink as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing 600mm x 450 mm ( six hundred x four hundred fifty millimetre) beveled edge mirror of superior glass mounted on 6mm thick A.C. Sheet or plywood sheet and fixed to wooden plugs with C.P. Brass screws and washers as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing C.P. Brass Towel rail complete with C.P. Brass brackets fixed to wooden plugs with C.P. Brass screws 600mm x 20mm (six hundred x twenty millimetre) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing 600mm x 120 mm (six hundred x one hundred twenty millimetre) glass shelf with C.P. Brass bracket and guard rail complete, fixed to wooden plugs with C.P. Brass screws as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing toilet paper holder C P Brass as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing liquid soap container with C.P. Brass lid and brackets fixed to wooden plugs with C.P. Brass screws as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. Glass container

Providing and fixing CP brass soap dish with brass bracket fixed on wooden cleat complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing 15 mm (Fifteen millimetre) dia C.P. Brass bib tap with Capstan head of Jaguar as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing 15 mm (Fifteen millimetre) dia C.P. Brass pillar tap with Capstan head 15 mm(Fifteen millimetre) dia of Jaguar as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing P.V.C. connection with Brass unions 300/450 mm (three hundred/four hundred fifty millimetre) length15 mm(fifteen millimetre) nominal size as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing brass full way valve with wheel as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

15 mm (fifteen millimetre) nominal bore

20 mm (twenty millimetre) nominal bore

25 mm (Twenty Five Millimetre) nominal bore

Providing and fixing brass ball valve (horizontal plunger type) High pressure with polythene plastic floats 15 mm (fifteen millimetre) nominal bore as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals

Providing and fixing PVC water storage tank of ISI : 12701 marked, G.I. inlet and outlet connection, 15mm (Fifteen millimetre) nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting up to all heights above ground level 1000 litres(one thousand litres) net capacity tank as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals

Providing and fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete.110*90 mm (one hundred ten x ninty millimetre) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals

Providing and fixing high pressure PVC spigot and socket waste and ventilating pipes confirming to ISI -15328 SN8 of Supreme/Fenolex/Kitech marked including fixing with approved adhesive etc. complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. 110 mm (one hundred ten milimetre)dia (one hundred ten) dia

Providing and fixing 110 mm ( one hundred ten millimetre) dia PVC single equal branch with oval access door, ISI marked insertion rubber washer 3 mm (three millimetre) thick bolts and nuts complete /including fixing with approved adhesive etc. complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals

Providing and fixing 110 mm ( one hundred ten millimetre) dia PVC door bend with oval access door insertion rubber washer 3 mm (Three millimetre) thick bolts and nuts ISI market complete including fixing with approved adhesive etc. complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals

Providing and fixing 110 mm ( one hundred ten millimetre) dia PVC Collar ISI marked including fixing with approved adhesive etc. complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals

Providing and fixing 110 mm ( one hundred ten millimetre) dia PVC plain bends ISI marked including fixing with approved adhesive etc. complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals

Providing and fixing 110 mm ( one hundred ten millimetre) dia PVC clamps ISI marked of approved design with steel screws and rawal plugs etc. complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals

Providing and fixing PTMT grating round of approved quality and colour 100 mm (hundred millimetre )nominal dia as per directionof Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Construction manhole with R.C.C to slab in 1:2:4 mix in (One cement:two sand:four graded stone aggregate 20 mm (twenty milimetre)nominal size) inside plastering 15 mm (fifteen milimetre)thick with cement mortar 1:3 (One cement:three sand)finished with a floating coat of neat cement and making channels in concrete 1:2:4 mix in (One cement:two sand:four graded stone aggregate 20 mm (twenty milimetre)nominal size) finished smooth complete including curring and testing inside size 800x800 mm (Eight hundred into eight hundred milimeter)deep including C.I cover and frame (medium duty) 455x610mm (four hundred fifty five into six hundred ten) internal diametres total weight of cover and frame to be not less then 38 Kg (thirty eight kilogram) (weight of cover 23 Kg. (twenty three kilogram) weight of frame 15 kg. (fifteen kilogram)with 300 mm (three hundred millimetre) thick walls of square rubble masonry in cement mortar 1:3 (One cement:three sand) as per the direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Ishant Gupta

KULBIR KUMAR