Construction of Transit Camp-II at Cotton Road, Tezpur, Assam

Amount

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge All kinds of soil.

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming ofbottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. Ordinary soil

Filling available excavated earth (excluding rock) in trenches, plinth,sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m.

Supplying and filling in plinth with sand under floors, including watering,ramming, consolidating and dressing complete.

Providing soling in foundation and under floor with stone/best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering complete. Stone soling of thickness 150mm.

Pre construction anti-termite treatment at the bottom of foundation pits and walls on either side upto a height of 300mm from bottom of the excavation made colum, plinth beam,walls, trenches etc. by applying the emulsion @5(five) litrs per square meter of the surface area before starting construction work (supplying necessary tools & accessories by the contractor as per direction of the department complete. a) With aqueous emulsion having concentration 1:19 with chloropirophose solution (tricel or equivalant) and water, i.e 1% solution.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level. 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level. 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

Steel reinforcement for R.C.C. work including straightening, cutting,bending, placing in position and binding all complete upto plinth level. Cold twisted bars For Footing,Column up to PL,Plinth/Tie Beam

Steel reinforcement for R.C.C. work including straightening, cutting,bending, placing in position and binding all complete above plinth level. Cold twisted bars (For Column above GL ,Chajja,Lintel Beam,Slab Beam,ST Cover,Kitchen Slab)

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform

Centering and shuttering including strutting, propping etc. and removal of form for Edges of slabs and breaks in floors and walls under 20 cm wide

Centering and shuttering including strutting, propping etc. and removal of form for Shelves (Cast in situ)

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers

Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of ntering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size de rived from natural sources)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns,pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, alconies, shelves, chajjas, lintels,bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering,finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarsesand(zone-III) derived from natural sources : 3 graded stone aggregate20 mm nominal size derived from natural sources).

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20mm nominal size derived from natural sources).

Brick work with common brunt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand)

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified Floor Tiles polished finish of Size of Tile 600x600 mm

Providing Antiskid Tiles of approved quality, Size, shape and thickness not less than 8mm on floor, skriting over a cement morter bed of 15mm thickness 1:3 (1 cement : 3 course sand) approved make fixed with Fix-A-Tie (Chokesy/Sika/Pedelite/Rouf)/ white cement complete at all level as specified & directed. Vitrified Executive range-2 (Size 600mmx600mm and above) Nitco Made Imperia Series-Gres Tiles

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 800x800 mm.

Providing polished vitrified wall tiles of approved quality, size, shape and thickness not less than 8mm on walls and skirting over cement morter bed of 10mm thick in prop. 1:3 (1 Cement : 3 Course sand) including cutting where necessary finished and flush pointing with Fix-A-Tie (Choksey/Sika/Pedelite/ Rouf)/white cement slurry mixed with approved pigment to match shade of tilesc complete at all levels as specified and directed. (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the department). of size 300mmx600mm and above.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite stone slab of colour black Cherry/Rubby Red Area of slab over 0.50 sqm

Extra for providing opening of required size & shape for wash basin/kitchen sink in kitchen platform,vanity ounter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. cludingmoulding, rubbing and polishing of cut edges etc.complete.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).

Providing and fixing ISI marked flush door shutters conforming to IS :2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing ISI marked flush door shutters conforming to IS :2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing factory made PVC Door shutter made of solid foam PVC profiles of thickness 5 mm and 15 mm at edges integrally extruded for vertical style and horizontal (top / bottom / lock) rails of minimum cross section of 70mm x 28mm, of shape and design as per manufacturer's specifications having homogenous fine cellular structure and smooth integral outer skin, inserted with G.l. 'C' section/ rectangular tube profile of minimum 0.30 mm thickness with 120 gsm coating as stiffeners as per manufacturer's specifications Mitered cut joints for styles and rails provided with telescopic polymeric L' corners are joined together using solvent adhesive and strengthened with fully threaded stainless steel screws (of required size) through reinforcement stiffener with paneling of specified solid foam PVC board / high pressure laminate of required thickness and of approved design and shade (matching the styles and rails), secured within styles and rails with specially designed solid foam PVC moulded headings of required size using PVC solvent adhesive / cement. The finished door shutter including SS hardware, 1 no. SS sliding door bolt 200 x 10mm, 1 no. SS tower bolt 200 x 10mm and 2 nos. SS handles 125 mm, shall be fixed to frame with 3 Nos. stainless steel hinges of minimum size 100x58x1.9mm and stainless steel screws of required size complete as per direction of the Engineer-in-Charge.(Cost of above hardware is inclusive in rates) 5 mm thick solid foam PVC panel of required size with moulded/extruded beading of appropriate design shape and size as per manufacturer's specifications (to secure the panel insert tight in place within the style and rails of the shutter)matching the color &shade of shutter frame - Non decorative type.

Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured).

Providing and fixing factory made door frame (single rebate) made out of solid foam PVC extruded profile of minimum 60 mm width and minimum 30 mm thickness, having homogenous fine cellular structure and integral smooth outer skin. The frame's vertical and horizontal members to be mitered cut and joined together with PVC solvent adhesive / cement and both corners strengthened with fully threaded steel screws (of required size) fixed diagonally. The door frame is to be fixed to door jambs using 6 Nos. SS 304 grade minimum 8 mm dia CSK Phillips stainless steel self tapping screws/fasteners with PA6 grade polyamide sleeves both of required size, and gap if any between the door frame and the jamb must be filled with clear silicon, complete as per direction of the Engineer-in- Charge.

Providing 40x5 mm flat iron hold fast 40 cm long including fixing toframe with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).

Providing barge board of size 200mmx20mm with Ist class local Hollock/Bonsum timber including fitting and fixing with necessary wood screws etc. complete.

Providing, fitting and fixing coloured anodised aluminium sliding windows and ventilators of standered sections of approved brand (HINDALCO/NALCO/BALCO/JINDAL/other equivvalent primary producer) without horzontal glazing bars, joints mitred and welded (manufactured to relevant IS specifications) and providing and fixing handels, angle cleat, rubber gusket, roller, bolting device, locking arrangements, serews etc as required complete as specified and directed for all levels. 2 Track sliding Windows 5 mm frosted glass

Providing, fitting and fixing coloured anodised aluminium sliding windows and ventilators of standered sections of approved brand (HINDALCO/NALCO/BALCO/JINDAL/other equivvalent primary producer) without horzontal glazing bars, joints mitred and welded (manufactured to relevant IS specifications) and providing and fixing handels, angle cleat, rubber gusket, roller, bolting device, locking arrangements, serews etc as required complete as specified and directed for all levels. 3 Track sliding window 5 mm coloured glass

Supplying , fitting & fixing anodised aluminium decorated grill with anodised aluminium rectangular frame of "F" and "H" section fitted with walls, columns or stiffeneres by special type of screws as per specification by the department for all levels. (Aluminium Alloy procured from primary aluminium producer (on submission of certificate of alloy purchaging from primary producer)

Providing & fixing false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Non combustible as per BS 476 (part 4)-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanised iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main-T runners of size 15x32 mm of length 3000 mm, cross - T of size 15x32 mm of length 1200 mm and secondary intermediate cross-T of size 15x32 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge. With fully perforated 12 mm thick micro tegular edged or 10 mm thick square edged GRG false ceiling tiles.

Providing and fixing M.S. fan clamp type I or II of 16 mm dia M.S. bar, bent to shape with hooked ends in R.C.C. slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. :Concealed work, including cutting chases and making good the walls etc. 20 mm nominal outer dia .Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. :Concealed work, including cutting chases and making good the walls etc. 25 mm nominal outer dia .Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 32 mm nominal outer dia. Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 50 mm nominal outer dia. Pipes.

Supplying fitting and fixing C.P.Bib cock 15mm dia of approved brand as directed and spoecified (G.I & C.P pipes will be measured seperately). Jaquare make Continental/Clarion 2- way bib-cock.

Supplying fitting and fixing Chrome Plated (C.P) Sink cock of approved brand as directed and spoecified (G.I & C.P pipes will be measured seperately). Jaquare make Continental/Clarion Sink cock with swinging spout.

Supplying fitting and fixing chrome plated (C.P) stop cock of approved brand and size as mentioned below as directed and spoecified (G.I & C.P pipes will be measured seperately). Jaquare make Continental/Clarion 15mm dia (Angular stop cock with long tread)

Supplying fitting and fixing chrome plated (C.P) stop cock of approved brand and size as mentioned below as directed and spoecified (G.I & C.P pipes will be measured seperately). Jaquare make Continental/Clarion 15 mm dia. (Concealed stop cock extra heavy with adjustable wall flange.

Supplying fitting and fixing CP Pillar cock of 15mm dia of approved brand as specified and directed. Jaquare make Continental

Supplying fitting and fixing Chrome Plated (C.P) spray shower 15mm dia of approved brand as directed and specified. (Pipes will be measured and paid seperately) Jaquar make Continental Shower Arm 190mm long heavey casted body with wall flange

Supplying, fitting and fixing Chrome Plated (C.P) wall mixer complete as directed. Jaquar make Continental/Clarion Wall mixer non telephonioc shower arrangement only Cat No.219

Providing, fitting and fixing Chrome Plated waste coupling complete as directed and specified. Jaquar Make 32 mm (HT/FT) (CAT No. ALD-705/709)

Providing, fitting & fixing of 450 mm long Braided Hose (C.P. Connection pipe) with two Nos 15 mm nuts & rubber washer without nipple suitable for Geysers of approved brand and manufacture complete. a) Jaguar Make (Premium quality) Code No. ALD-805B

Providing, fitting and fixing C.P. Brass Hand Shower (Health Faucet Metallic) including 8mm dia 1.20M long flexible tube wall hook etc. of approved brand and manufacture confirming to IS standered complete as directed and specified.

Providing fitting & fixing decorative mirror complete as directed & specified. Jaquar Make Swival mirror (Cat. No.ACN-1195N)

Providing fitting & fixing Glass shelf complete as directed & specified. Glass shelf with C.P. guard rail Jaquar Make Continental 550mm long (Cat. No.ACN-1171N)

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets,40 mm flush end, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required W.C. pan with ISI marked white solid plastic seat and lid.

Providing vitreous China wash basin with CI/MS brackets, CP brass chain with plug, PVC waste pipe including painting of fittings & brackets, cutting and making good the walls whereever required. (Piller cocks, waste cupling are to paid seperately). Pedestal Basin (with pedstal) Jaqure make White Opal (Cat. No.OPS-WHT-0610)

Providing fitting & fixing stainless steel kitchen sink of Parryware make with CI/MS brackets, C.P. brass chain with rubber plug, PVC waste pipe etc. complete including painting the fittings, & making good the walls whereever required. (Sink cock, stop cock, waste coupling are to be paid seperately) Nirali Grace Plain Jumbo (Bowl Size 610x460x254) Glossy.

Providing fitting & fixing white vitreous glazed drain board of Hindware make size (530x450) of Hindware (Cat.No.51001) including painting of brackests complete. Size (530 x 450) of Hindware (Cat No. 51001)

Providing fitting & fixing Mirror with plastic frame of size 500 x 400 mm complete as directed and specified.

Providing fitting & fixing CP soap tray / soap dish complete as directed & specified. Jaquar Make Continental (Cat.ACN-1331N)

Providing fitting & fixing Liquid soap dispenser and liquid soap container complete as directed & specified. Jaquar Make Continental (Cat.No.ACN - 1135N) (With glass bottle)

Providing fitting & fixing CP Towel Rail complete as directed and specified. Jaquar Make Continental 300mm for wash basin (Cat.No.ACN - 1101N).

Providing fitting & fixing CP Towel Rail complete as directed and specified. Jaquar Make Continental 600mm (Cat.No.ACN - 1111N).

Providing fitting & fixing Chrome Plated Towel Ring complete as directed and specified. Jaquar Make Continental towel ring round (Cat.No.ACN - 1121BN).

Providing fitting & fixing Chrome Plated TOILET PAPER holder complete as directed and specified. Jaquar Make Continental toilet paper holer with flap (Cat.No.ACN - 1153N).

Providing fitting & fixing Chrome Plated Tumber & Bruss holder of Parryware make (Cat. No.9947) complete as directed and specified.

Providing fitting & fixing PVC pipes of 6kg/cm2 (Supreme/Prince) or other ISI approved inmcluding jointing, fitting and fixing with clamps etc. as necessary complete at all levels including below GL as directed and specified. In exposed surfaces or in trenches. 110 mm dia

Providing fitting & fixing PVC pipes of 6kg/cm2 (Supreme/Prince) or other ISI approved inmcluding jointing, fitting and fixing with clamps etc. as necessary complete at all levels including below GL as directed and specified. In exposed surfaces or in trenches. 75 mm dia

Supplying fitting & fixing 45 degree PVC bend of (Supreme/Prince) or orther ISI approved including jointing, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. In exposed surface or in trenches 110 mm dia.

Supplying fitting & fixing 45 degree PVC bend of (Supreme/Prince) or orther ISI approved including jointing, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. In exposed surface or in trenches 75 mm dia.

Supplying fitting & fixing PVC plain single Tee with door of (Supreme/Prince) or orther ISI approved including jointing, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. In exposed surface or in trenches 110 mm dia.

Supplying fitting & fixing PVC socket plug of (Supreme/Prince) or orther ISI approved including jointing, fitting and fixing etc. in exposed surface or trences as necessary complete at all levels including below G.L. as directed and specified. 110 mm dia.

Supplying fitting & fixing PVC socket plug of (Supreme/Prince) or orther ISI approved including jointing, fitting and fixing etc. in exposed surface or trences as necessary complete at all levels including below G.L. as directed and specified. 75 mm dia.

Supplying fitting & fixing PVC cowl of ISI mark complete as directed and specified. 110 mm dia.

C.P.Grating 110mm dia

Supplying, fitting, fixing brass fittings of approved make, reasonably smooth, free from sharp edges and conners, flaws and other defects and with counter shunk holes for screws including necessary C.P.Brass screws etc. complete (Bright natural matt & satin finished).. Sliding door bolts 300mm x 16mm.

Supplying, fitting, fixing brass fittings of approved make, reasonably smooth, free from sharp edges and conners, flaws and other defects and with counter shunk holes for screws including necessary C.P.Brass screws etc. complete (Bright natural matt & satin finished) Tower Bolt 300mmx10mm

Supplying, fitting, fixing brass fittings of approved make, reasonably smooth, free from sharp edges and conners, flaws and other defects and with counter shunk holes for screws including necessary C.P.Brass screws etc. complete (Bright natural matt & satin finished) Tower Bolt 250mm x 10mm

Supplying, fitting, fixing brass fittings of approved make, reasonably smooth, free from sharp edges and conners, flaws and other defects and with counter shunk holes for screws including necessary C.P.Brass screws etc. complete (Bright natural matt & satin finished) Door Handles 150mm

Supplying, fitting, fixing brass fittings of approved make, reasonably smooth, free from sharp edges and conners, flaws and other defects and with counter shunk holes for screws including necessary C.P.Brass screws etc. complete (Bright natural matt & satin finished) Door Handles 100mm

Supplying, fitting, fixing brass fittings of approved make, reasonably smooth, free from sharp edges and conners, flaws and other defects and with counter shunk holes for screws including necessary C.P.Brass screws etc. complete (Bright natural matt & satin finished) Night latches Mortice night latches (Godrei make)

Supplying, fitting, fixing brass fittings of approved make, reasonably smooth, free from sharp edges and conners, flaws and other defects and with counter shunk holes for screws including necessary C.P.Brass screws etc. complete (Bright natural matt & satin finished) Mortice lock Cylindrical type (Godrej) polished Brass

Providing fitting & fixing Door Closer of various type UL listed and fire rated good quality depending on the door specification. Types like Single Speed, Double Speed, Heavy duty etc. are available and as directed & specified by the department Godrej Double speed Door Closer (size 140mm x 39mm x 60mm) Model Number C 752

Supplying fitting & fixing drapery rods along with all accessories in doors windows and other openings completed as specified and directed by the department at alllevels. Mettalic Drapery rod

12 mm cement plaster of mix 1:4 (1 cement: 4 fine sand)

15 mm cement plaster on the rough side of single or half brick wall of mix : 1:4 (1 cement: 5 fine sand)

12 mm cement plaster finished with a floating coat of neat cement of mix : 1:4 (1 cement: 4 fine sand)

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre

Finishing walls with Acrylic Smooth exterior paint of required shade New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Wall painting with premium acrylic emulsion paint of interior grade,having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two Coats.

Applying priming coat: With ready mixed aluminium primer of approved brand and manufacture on resinous wood and plywood.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Painting with black anti-corrosive bitumastic paint of approved brand and manufacture to give an even shade: Two or more coats on new work.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation,levelling & dressing & finishing the top smooth.

Providing drain with cement concrete (1:3:6) 10cm thick sides 10cm thick bed over brick flat soling including 15mm thick cement plastering in prop. 1:3 finished with a floating coat of neat cement slurry as directed with necessary shuttering for sides and earth work in excavation of foundation trencehs and refilling the sides afetr completing of work etc. as specified. 300mm wide and average 250mm deep with bed slope 1 in 150 with initial depth of 100mm.

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. a) With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design: Inside dimensions 455x610 mm and 45 cm deep for single pipe line : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing Pre-Painted Galvanished Iron Sheet Roofing (PPGI) at all levels including fitting and fixing with self drilling, self tapping screws complete. (Roof trusses, purlines etc. to be measured and paid separately) TATA Blue scope/Dyna roof/Wonder roof or equivalent as directed by the Department. a) 0.45 mm thick.

Providing Pre-Painted Galvanished Iron Sheet Roofing (PPGI) accessories (Ridges/Vally/Gutter/Flashing) at all levels including fitting and fixing with self drilling, self tapping screws complete. TATA Blue scope/Dynaroof/Wonder roof or equivalent as directed by the Department. v) 0.45 mm thick.

Providing fitting & fixing wind ties with 40mmx6mm M.S flat iron and necessary 10mm dia G.I. hook bolt, G.I flat washer and bitumen washer etc. complete including two coats painting with red oxide anticorrosiv paint.

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. Group C

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 1 No 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required 2 X 6 sq. mm + 1 X 6 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required 2 X 10 sq. mm + 1 X 10 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required 2 X 16 sq. mm + 1 X 16 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required 4 X 6 sq. mm + 2 X 6 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required 4 X 10 sq. mm + 2 X 10 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required 4 X 16 sq. mm + 2 X 16 sq. mm earth wire

Supplying and drawing following pair 0.5 sq mm FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 1 Pair

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required. 20 mm

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required 25 mm

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 20 mm

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 5/6 amps switch

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 2 way 5/6 amps switch

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 15/16 amp switch

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 3 pin 5/6 amp socket outlet

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 6 pin 15/16 amp socket outlet

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. Telephone socket outlet

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. TV antenna socket outlet

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. Bell push

Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required. 1 or 2 Module (75mmX75mm)

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required. 3 Module (100mmX75mm)

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required. 4 Module (125mmX75mm)

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required. 6 Module (200mmX75mm)

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required. 8 Module (125mmX125mm)

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required. 12 Module (200mmX150mm)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required.

Supplying and fixing call bell/ buzzer suitable for single phase, 230 volts, complete as required.

Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable and earthing etc. as required.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. Upto 450 mm sweep

Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes.

Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve including connections, painting etc. as required.

Providing and fixing following rating and breaking capacity MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. 100 Amp, 30 KA MCCB

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 6 way (4 + 18), Double door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's (but without MCB's and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 8 way (4 + 24), Double door

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Double pole

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps

Supplying and fixing DP sheet steel enclosure on surface/ recess along with 25/32amps 240 volts "C" curve DP MCB complete with connections, testing and commissioning etc. as required.

Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, GI tube, having single prong at top, with 85 mm dia 6 mm thick GI base plate including holes etc. complete as required.

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run)

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run)

Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required.

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in existing RCC / HUME / METAL pipe as required. Upto 35 sq. mm

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in existing RCC / HUME / METAL pipe as required. Above 35 sqmm and upto 95 sq. mm

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. Upto 35 sq. mm (clamped with 1mm thick saddle)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3.5 X 50 sq. mm (35mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 4 X 35 sq. mm (32mm)

Supplying, fixing, connecting, testing and commissioning of following rating, ISI marked (IS 8828) 240 / 415 volts, 10 KA, Miniature Circuit Breaker (MCB) of single / double / three / four poles in the existing MCB DB or in existing MS enclosure complete in all respects. 40 Amp. FP MCB

Supplying, fixing, connecting, testing and commissioning of following rating, ISI marked (IS 8828) 240 / 415 volts, 10 KA, Miniature Circuit Breaker (MCB) of single / double / three / four poles in the existing MCB DB or in existing MS enclosure complete in all respects. 40 Amp. TP MCB

Supply of ISI marked aluminium conductor XLPE insulated cable as per IS 7098, armoured, served, sheathed 1100 volts grade. 4 x 35 Sqmm

Supply of ISI marked aluminium conductor XLPE insulated cable as per IS 7098, armoured, served, sheathed 1100 volts grade. 3.5 x 50 Sqmm

Supply of Ceiling Fan

Supply of Exhaust Fan

jayshree electricals (BID ID -811548)

PABITRA SAIKIA (BID ID -811463)

MANOJ KUMAR SARMAH (BID ID -811821)

Pranjal Chakravarty (BID ID -810108)

SAMIM AKHTER CHOUDHURY (BID ID -811895)

M/s S.T Enterprises (BID ID -811004)