REPAIR / MAINT OF SUBMERSIBLE PUMP, CENTRIFUGAL PUMP, NON CLOGGING PUMP, DIESEL DRIVEN PUMP, LAND SCAPING LIGHTS FITTNG, GATE LIGHTS BUILDING, STREET LIGHTS AND TIMER CONTROL PANEL ALONG WITH OTHER CONNECTED WORKS AT AF-I UNDER GE (AF) JAMNAGAR NO.2

Amount

M & L for disconnecting electrical connection & outlet pipe connection, taking out submersible pump and motor of any capacity from the tube well/borewell lowered at the depth of 100m and above from the ground level complete with HDPE pipe and submersible cable, transport to authorized workshop for repair/servicing, brought back to existing location and lowering the same pump after repairing / servicing along with HDPE pipe and electric cable including fixing of cable to pipe with PVC strip, replacement of clamps and mild steel bolts, nut and washers with stainless still nut and bolt, casing capping bell cap etc, reconnecting electrical & delivery pipe line complete all as specified and directed. Note:- (i) Repairing/Servicing of submersible pump & motor shall be measured & paid separately. (ii) Cable & HDPE pipe if found unserviceable and steel shaft as per existing dia incl metaling of pump shaft, grinding & polishing shall be measured and paid separately.

M&L for repairing / servicing of unserviceable 15 HP to 30 HP capacity submersible pump by dismantling the pump and taking out defective / unsv / wornout parts of submersible pump set and replacement / servicing of all defective parts as under and reassembling the pump set including testing complete all as specified and directed.

Stainless steel Shaft as per existing dia incl metaling of pump shaft , grinding & polishing

Thrust plate

Distance sleeves

Bearings as per existing(02 nos in each) with bearing sleeve

Stage Ball

Neck Ring

oil seal

Non return valve cast iron

Stainless steel filter cage

Impeller or diffuser stainless steel as per casing dia

Alignment of pump impeller with motor shaft

Bearing bush made of rubber

M&L for repairing / servicing of unserviceable electric motor cap 15HP to 30HP couplled to submersible pump, AC 3 phase, by dismantling the motor and coupling pulley and sent to workshop for repair. Removal of existing burnt out copper winding wire , cleaning of slots using suitable reagents and rewinding with super enamelled copper winding wire of appropriate gauge to achieve required RPM, varnsihing, drying, ovening, overhauling, greasing, painting and assembling the same after complete repair, connecting with pump and making necessary electrical connection and testing of motor after installation complete all as specified and directed. Note: Contractor shall be responsible for maintaining required RPM after repair, non compliance of speed considered as incomplete repair.

M&L for repairing / servicing of unserviceable submersible pump of cap 7.5 HP to 12.5 HP by dismantling the pump and taking out defective / unsv / worn out parts of submersible pump set and replacement / servicing of all defective parts as under and reassebling the pump set including testing complete all as specified and directed.

Stainless steel shaft as per existing dia incl metaling of pump shaft, grinding & polishing

Thrust plate

Distance sleeves

Bearings as per existing (02 nos in each) with bearing sleeve

Stage Ball

Neck Ring

Oil seal

Non return valve cast iron

Stainless steel filter cage

Impeller or diffuser stainless steel as per casing dia

Alignment of pump impeller with motor shaft

Bearing bush made of rubber

M&L for repairing / servicing of unserviceable electric motor cap of 7.5HP to 12.5 HP couplled to submersible pump, AC 3 phase, by dismantling the motor and coupling pulley and sent to workshop for repair. Removal of existing burnt out copper winding wire, cleaning of slots using suitable reagents and rewinding with super enamelled copper winding wire of appropriate gauge to achieve required RPM, varnsihing, drying, ovening, overhauling, greasing, painting and assembling the same after complete repair, connecting with pump and making necessary electrical connection and testing of motor after installation complete all as specified and directed. Note: Contractor shall be responsible for maintaining required RPM after repair, non compliance of speed considered as incomplete repair.

Supply and fix in repair submersible pump cable, PVC insulated, PVC sheathed, multi stranded copper conductor cable 1100 volts grade and connecting complete including taking out old unsv damaged cable of following sizes:-

6 sqmm 3 core

10 sqmm 3 core

M & L for disconnecting electrical connection & outlet pipe connection, taking out unsv monoblock pumping set of any capacity from the foundation channel, shifting of pumping set (pump with motor) to authorized workshop for repair, dismantling of pump and motor for carrying out repair, testing of motor after repair, reassembling of pumping set (pump and motor) and refix at site, reconnecting electric and delivery pipe line complete all as specified and directed. Note:- (i) Repairing / Servicing of monoblock pump set shall be measured & paid separately. (ii) Cost of material required for refixing after repair shall be borne by contractor.

M&L for repairing / servicing of unserviceable monoblock pump set of suitable capacity couplled with 12.5HP electric motor by dismantling the pump and taking out defective / unsv / worn out parts of submersible pump set and replacement / servicing of all defective parts as under and reassembling the pump set including testing complete all as specified and directed.

Repairing of shaft by remetaling / welding, grinding and polishing

Bearings as per existing (02 nos in each) with bearing sleeve for DE/NDE

Oil/water seal

Impeller or diffuser stainless steel as per casing dia

Alignment of pump impeller with motor shaft

Impeller lock nut

M&L for Repairing / Servicing of unserviceable monobloc pump set of suitable capacity couplled with 3HP to 5HP electric motor by dismantling the pump and taking out defective/unsv/worn out parts of submersible pump set and replacement/servicing of all defective parts as under and reassebling the pump set including testing complete all as specified and as directed by Engr-in-charge

Repairing of shaft by remetaling/welding, grinding and polishing

Bearings as per existing (02 nos in each) with bearing sleeve for DE/NDE

oil/water seal /Mechanical seal assembly

Impeller or diffuser stainless steel as per casing dia

Alignment of pump impeller with motor shaft

Suction flange

Impeller lock nut

Terminal box cover

Capacitor of suitable size

Cooling fan with cover

M&L for dismantling of existing defective / unsv squirrel cage induction motor of capacity 3 to 5 HP, single phase, 415 V, 50 Hz, from the foundation, disconnecting the electric connection, coupling pulley, transportation to workshop, seperating the stator and rotor assembly, cutting down and removing existing burnt out copper winding wire, cleaning of slots and rewinding of stator with super enamelled solid copper conductor (winding wire) of appropriate gauge and size to match with the existing so as to acheive desired RPM, including varnishing, drying, ovening, overhauling, greasing, provising insualtion and reassembling stator and rotor, connecting coils / winding, fixing in the same position, making necessary electric connection and testing of induction motor complete all as specified and directed.

M&L for dismantling of existing defective/unsv squirrel cage induction motor of capacity 12.5 HP, three phase, 415 V, 50 Hz, from the foundation, disconnecting the electric connection, coupling pulley, transportation to workshop, seperating the stator and rotor assembly, cutting down and removing existing burnt out copper windings, cleaning of slots and rewinding of stator with super enamelled solid copper conductor (winding wire) of appropriate gauge and size to match with the existing so as to acheive desired RPM, including varnishing, drying, ovening, overhauling, greasing, provisioning insualtion and reassembling stator and rotor, connecting coils/ winding in star and delta mode at the junction box/terminal, fixing in the same position, making necessary electric connection and testing of induction motor complete all as specified and directed.

M & L for disconnecting electrical connection & outlet pipe connection, taking out unsv centrifugal pump set of any capacity from the foundation channel, shifting of pumping set (pump with motor) to authorized workshop for repair, dismantling of pump and motor for carrying out repair, testing of motor after repair, reassembling of pumping set (pump and motor) and refix at site, reconnecting electric and delivery pipe line connection complete all as specified and directed. Note:- (i) Repairing/Servicing of centrifugal pump set shall be measured & paid separately. (ii) Cost of material required for refixing after repair shall be borne by contractor.

M&L for repairing / servicing of unserviceable centrifugal pump set of suitable capacity couplled with 50HP electric motor by dismantling the pump and taking out defective / unsv / worn out parts of pump set and replacement of all defective parts as under and reassembling the pump set including testing complete all as specified and directed.

Repairing of shaft by remetaling / welding, grinding and polishing

Bearings as per existing (02 nos in each) with bearing sleeve for DE/NDE

Oil/water seal / Mechanical seal assembly

Impeller or diffuser stainless steel as per casing dia

Alignment of pump impeller with motor shaft

Lantern ring

Impeller lock nut

Terminal box cover

Gland

Coupling with rubber bush as per existing

Pump Gasket

Shaft sleeve

Repairing of shaft by remetaling/welding, grinding and polishing

M&L for repairing / servicing of unserviceable centrifugal pump set of suitable capacity couplled with 20HP electric motor by dismantling the pump and taking out defective / unsv / worn out parts of pump set and replacement of all defective parts as under and reassembling the pump set including testing complete all as specified and directed.

Bearings as per existing (02 nos in each) with bearing sleeve for DE/NDE

Oil / water seal / Mechanical seal assembly

Alignment of pump impeller with motor shaft

lantern ring

Impeller lock nut

Gland

Coupling with rubber bush as per existing

Pump Gasket

Shaft sleeve

Pump wear ring and Pump shoulder ring

M&L for repairing / servicing of unserviceable centrifugal pump set of suitable capacity couplled with 40HP electric motor by dismantling the pump and taking out defective / unsv / worn out parts of pump set and replacement of all defective parts as under and reassembling the pump set including testing complete all as specified and directed.

Bearings as per existing (02 nos in each) with bearing sleeve for DE/NDE

Oil / water seal / Mechanical seal assembly

Alignment of pump impeller with motor shaft

Lantern ring

Impeller lock nut

Gland

Coupling with rubber bush as per existing

Pump Gasket

Shaft sleeve

Pump wear ring and Pump shoulder ring

Key for coupling

Gland Packing

O ring

M&L for repairing / servicing of unserviceable centrifugal pump set of suitable capacity couplled with 75/100HP electric motor by dismantling the pump and taking out defective / unsv / worn out parts of pump set and replacement of all defective parts as under and reassembling the pump set including testing complete all as specified and directed.

Bearings as per existing (02 nos in each) with bearing sleeve for DE/NDE

Oil / water seal / mechanical seal assembly

Alignment of pump impeller with motor shaft

Impeller lock nut

Gland

Coupling with rubber bush as per existing

Pump Gasket

Shaft sleeve

Pump wear ring and pump shoulder ring

Key for coupling

Gland Packing

M&L for dismantling of existing defective / unsv squirrel cage induction motor of capacity 75 / 100HP, three phase, 415 V, 50 Hz, from the foundation, disconnecting the electric connection, coupling pulley, transportation to work shop, seperating the stator and rotor assembly,cutting down and removing existing burnt out copper windings, cleaning of slots and rewinding of stator with super enamelled solid copper conductor (winding wire) of appropriate gauge and size to match with the existing so as to acheive desired RPM, including varnishing, drying, ovening, overhauling, greasing, provising insualtion and reassembling stator and rotor, connecting coils/ winding in star and delta mode at the junction box/terminal, fixing in the same position, making necessary electric connection and testing of induction motor complete all as specified and directed.

M&L for dismantling of existing defective / unsv squirrel cage induction motor of capacity 50 HP, three phase, 415 V, 50 Hz, from the foundation, disconnecting the electric connection, coupling pulley, transportation to workshop, seperating the stator and rotor assembly, cutting down and removing existing burnt out copper windings, cleaning of slots and rewinding of stator with super enamelled solid copper conductor (winding wire) of appropriate gauge and size to match with the existing so as to acheive desired RPM, including varnishing, drying, ovening, overhauling, greasing, provisioning insualtion and reassembling stator and rotor, connecting coils / winding in star and delta mode at the junction box/terminal, fixing in the same position, making necessary electric connection and testing of induction motor complete all as specified and directed.

M&L for dismantling of existing defective / unsv squirrel cage induction motor of capacity 40 HP, three phase, 415 V, 50 Hz, from the foundation, disconnecting the electric connection, coupling pulley, transportation to workshop, seperating the stator and rotor assembly, cutting down and removing existing burnt out copper windings, cleaning of slots and rewinding of stator with super enamelled solid copper conductor (winding wire) of appropriate gauge and size to match with the existing so as to acheive desired RPM, including varnishing, drying, ovening, overhauling, greasing, provisioning insualtion and reassembling stator and rotor, connecting coils / winding in star and delta mode at the junction box/terminal, fixing in the same position, making necessary electric connection and testing of induction motor complete all as specified and directed.

M&L for dismantling of existing defective / unsv squirrel cage induction motor of capacity 20 HP, three phase, 415 V, 50 Hz, from the foundation, disconnecting the electric connection, coupling pulley, transportation to workshop, seperating the stator and rotor assembly, cutting down and removing existing burnt out copper windings, cleaning of slots and rewinding of stator with super enamelled solid copper conductor (winding wire) of appropriate gauge and size to match with the existing so as to acheive desired RPM, including varnishing, drying, ovening, overhauling, greasing, provisioning insualtion and reassembling stator and rotor, connecting coils / winding in star and delta mode at the junction box/terminal, fixing in the same position, making necessary electric connection and testing of induction motor complete all as specified and directed.

Taking down old unserviceable 250mm bore, CI/DI/MS water mains (including all fittings) with spigot and socket ends and lead joints including burning out joints and recovering lead complete all as specified and directed.

Taking down old unserviceable 200mm bore, CI/DI/MS water mains (including all fittings) with spigot and socket ends and lead joints including burning out joints and recovering lead complete all as specified and directed.

M&L and testing for in replacement of 250mm bore, DI water mains (including all fittings) with spigot and socket ends and rubber tytan joints Class K9 in any length laid in trenches complete all as specified and directed.

M&L and testing for inreplacement of 200mm bore, DI water mains (including all fittings) with spigot and socket ends and rubber tytan joints Class K10 in any length laid in trenches complete all as specified and directed.

Taking out unserviceable / defective / damaged / blockage GI pipe 15mm bore steel water tubing,sorting out serviceable pipe fitting for reuse and cleaning the pipe including fitting and removing away all unserviceable pipe from site, complete all as specified and directed. Note: Exacavation and earth work shall be measured and paid for separately.

Taking out unserviceable / defective / damaged / blockage GI pipe 20mm bore steel water tubing,sorting out serviceable pipe fitting for reuse and cleaning the pipe including fitting and removing away all unserviceable pipe from site, complete all as specified and directed. Note: Exacavation and earth work shall be measured and paid for separately.

Taking out unserviceable / defective / damaged / blockage GI pipe 25mm bore steel water tubing,sorting out serviceable pipe fitting for reuse and cleaning the pipe including fitting and removing away all unserviceable pipe from site, complete all as specified and directed. Note: Exacavation and earth work shall be measured and paid for separately.

Taking out unserviceable / defective / damaged / blockage GI pipe 40mm bore steel water tubing,sorting out serviceable pipe fitting for reuse and cleaning the pipe including fitting and removing away all unserviceable pipe from site, complete all as specified and directed. Note: Exacavation and earth work shall be measured and paid for separately.

Taking out unserviceable / defective / damaged / blockage GI pipe 50mm bore steel water tubing,sorting out serviceable pipe fitting for reuse and cleaning the pipe including fitting and removing away all unserviceable pipe from site, complete all as specified and directed. Note: Exacavation and earth work shall be measured and paid for separately.

S&F GI tubing medium grade, ISI Marked conforming to IS 1239 Part-I 2004, 15mm bore with and including all fittings such as bends, elbows, tees, short length, socket, union, check nuts, nipples etc. fixed and laid in trenches / floor / under culvert / road crossing etc including testing complete all as specified and directed.

S&F GI tubing medium grade, ISI Marked conforming to IS 1239 Part-I 2004, 20mm bore with and including all fittings such as bends, elbows, tees, short length, socket, union, check nuts, nipples etc. fixed and laid in trenches / floor / under culvert / road crossing etc including testing complete all as specified and directed.

S&F GI tubing medium grade, ISI Marked conforming to IS 1239 Part-I 2004, 25mm bore with and including all fittings such as bends, elbows, tees, short length, socket, union, check nuts, nipples etc. fixed and laid in trenches / floor / under culvert / road crossing etc including testing complete all as specified and directed.

S&F GI tubing medium grade, ISI Marked conforming to IS 1239 Part-I 2004, 40mm bore with and including all fittings such as bends, elbows, tees, short length, socket, union, check nuts, nipples etc. fixed and laid in trenches / floor / under culvert / road crossing etc including testing complete all as specified and directed.

S&F GI tubing medium grade, ISI Marked conforming to IS 1239 Part-I 2004, 50mm bore with and including all fittings such as bends, elbows, tees, short length, socket, union, check nuts, nipples etc. fixed and laid in trenches / floor / under culvert / road crossing etc including testing complete all as specified and directed.

Taking out unserviceable / defective / damaged gate valve any size complete all as specified and directed.

Supply & fixing gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe of size 20mm, complete all as specified and directed.

Supply & fixing gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe of size 25mm, complete all as specified and directed.

Supply & fixing gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe of size 40mm, complete all as specified and directed.

Supply & fixing gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe of size 50mm, complete all as specified and directed.

M&L for repair to diesel engine opearted at 1800 RPM of cap 92HP/68KW Make: Kirloskar installed at WWR fire fighting pump house. Note: Mather & Platt with taking out and repair/replacement of defective parts as under:

Diesel filter element with gasket

Inhibitor corrosion, tube water bypass & water outlet

Air cleaner element

Engine oil filter element complete

Air filter (inner & outer)

Fuel filter bowl, pre element & micro element

Solenoid switch with wiring complete

Governor cable both inner and outer including RPM adjustment assembly

Set of ring set, dowel for connecting rod, bolt for connecting rod, conneting rod assembly and joint for gear assembly

Taking out choked radiator from engine, drain out coolant and descaling and cleaning with cleaning agent, cleaning of fins by applying pressurized air using blower including replacement of rubber housing set complete all as specified and directed.

Taking out old/unsv engine belt and replacement of grooved belt complete all as specified and directed.

Taking out fuel pump, transporting to authourised workshop, dismantling of pump carefully and overhauling complete all as specified and directed.

Draining out old unsv engine oil from chamber, cleaning of oil sump complete and filling of new oil 15W40CH4 confirming to specification complete all as specified and directed.

Taking out all leaked / deterioted rubber hoses of engine and replacement of hose pipes including clamps complete all as specified and directed.

Taking out old unsv fuel pipes and replacement of new nylon reinforced PVC fuel pipes with threaded sockets complete set, oil seal, seal O ring, screw captive washer cap complete all as specified and directed.

Scraping of old existing paint, oil from body of alternator, radiator, engine, base frame including exhaust pipe / silencer, preparation of surface and filling of cavity using filler material and spray painting to complete pump set and motor set alongwith all accessories including fuel tank with two coats of super enamelled paint of superior quality as approved by AGE E/M and writing of MES/SM No. using black paint of suitable font of letters in background of white paint complete all as specified and directed.

Disconnection of existing pipe connections and electrical connections, de-watering and lifting up the Non cloging type submersible pumps 5HP/3.7KW of discharge capacity 720 LPM (Make KSB) from UG sewage sump of 10.7 mtr deep carefully and transporting to workshop for repair and bringing back at site after repair and lowering the same including making the water and electric connection including commissioning and testing complete all as specified and directed. Note : (i) Repair of submersible pump and pump motor shall be measured & paid separately under respective item of this schedule. (ii) T&P shall be arranged by the contractor. (iii) Transportation of pump set from site to workshop and bringing back at site inclusive in quoted rate.

De-assembling of electric motor of 5HP / 3.7KW of non-cloging submersible pump set (Make KSB), cutting and removing the existing burnt winding wire of any gauge, cleaning and making good the slots, rewinding the electric motor with PVC insulated copper wire of existing size/gauge and weight, application of insulating material & varnishing including replacing of ball bearings-02 Nos, moisture seal and re-assembling the motor, commissioning & testing complete for the entire satisfaction of Engineer-in-charge all as specified and directed.

De-assembling of non-clogging submersible pump of discharge capacity 750 LPM, for repair by replacing of company recommended parts of Mechanical seal - 2 Nos, Lower Bearing - 1 No, O Ring - 1 No, Spiral plate - 1 No, Compay recommended Lubriucating oil - 7 Ltrs, Moisture sensor including bolts, nuts and washers, re-assembling the same and commissioning & testing complete all as specified and directed.

Excavation in trenches in hard dense soil n.exc 1.5 mtr wide & n.exc 1.5mtr in depth and n. exc. 10sqm on plan for laying pipe in trenches and getting out complete all as specified and directed.

Returning filling in trenches, spreading, levelling, watering and well ramming in layers n.exc 25cm in hard dense soil complete all as specified and directed.

Removing of surplus soil to a distance n.exc 50 mtr and depositing where directed at a level n.exc 1.5 mtr above starting point complete all as specified and directed.

Excavation in trenches not exc 1.5 m wide and n.exc 1.5 m in depth for foundation / fixing pole / laying cable and pipe line etc or for manhole etc not exc 10 sqm on plan and getting out in soft / loose soil all as specified

Supply & lay XLPE insulated, PVC inner sheathed, armoured with galvanised steel strip or wire, heavy duty, LT underground cable ISI marked with aluminium multistranded conductor 1100 volt grade of size 6 Sqmm 2 core laid in trenches / duct passing through pipe / duct or fixed on pole and connecting and testing etc including taking down old cable complete all as specified & directed by Engr -in-charge.

Supply & lay XLPE insulated, PVC inner sheathed, armoured with galvanised steel strip or wire, heavy duty, LT underground cable ISI marked with aluminium multistranded conductor 1100 volt grade of size 16 Sqmm 2 core laid in trenches / duct passing through pipe / duct or fixed on pole and connecting and testing etc including taking down old cable complete all as specified & directed by Engr-in-charge.

Supply & lay XLPE insulated, PVC inner sheathed, armoured with galvanised steel strip or wire, heavy duty, LT underground cable ISI marked with aluminium multistranded conductor 1100 volt grade of size 16 Sqmm 4 core laid in trenches / duct passing through pipe / duct or fixed on pole and connecting and testing etc including taking down old cable complete all as specified & directed by Engr -in-charge.

Material & labour for 50 mm bore GI steel tubing light grade for protection of cable / earth continuity conductor fixed to poles / walls / roof or laid in floors, road, crossing or ducts fixed with clamps , bolts nuts and washer etc including taking down old pipe complete all as specified and directed.

M&L for providing dry river sand as in sand cushioning 18cm before and 5 cm after laying of under ground electric cable, thickness specified in SSR Part -I, including punning down of sand in layer all as specified and directed by Engr-in-Charge. Note: For measurement purpose punned thickness of sand only will be considered.

Taking down old un reinforced precast concrete cable cover any type from the trenches etc

Laying only PCC cable cover for LT / HT UG cable, of any description retrieved from item No 60, all as specified and directed by Engr-in-Charge.

Supply & laying ISI marked & conforming to IS - 5820 - 1970 unreinforced precast concrete cable cover Class LV, flat of size 250 mm X 150 mm X 40 mm in trenches as protection to LT UG cable all as specified and directed by Engr-in-Charge.

S&F LED Street Light fitting 25 watt, system efficiency not less than 100 lumen / watt, IP65 protection, consisting of high / low voltage cut off, maintenance free isolated Electronic driver circuits, Low THD, PMMA grade high quality Transmittance lens, Epoxy powder coated Die Cast Aluminium housing with weather proof gasket for lamp & driver compartment, Heat resistance toughened glass fitted in cast aluminium housing with SS screws, fixed on existing bracket & connecting including taking down old light fitting of any description complete all as specified and directed.

S&F LED FLOOD Light fitting 70 watt, system efficiency not less than 100 lumen / watt, IP66 protection, consisting of high / low voltage cut off, maintenance free isolated Electronic driver circuits, Low THD, PMMA grade high quality Transmittance lens, Epoxy powder coated Die Cast Aluminium housing with unique lens system for enhanced uniform illumination and weather proof gasket for lamp & driver compartment, Heat resistance toughened glass fitted with silicon gasket for IP 66 protection in cast aluminium housing with SS screws fixed on existing bracket & connecting, including taking down old light fitting of any description complete all as specified and directed.

S&F LED FLOOD Light fitting 100 watt, system efficiency not less than 100 lumen / watt, IP66 protection, consisting of high / low voltage cut off, maintenance free isolated Electronic driver circuits, Low THD, PMMA grade high quality Transmittance lens, Epoxy powder coated Die Cast Aluminium housing with unique lens system for enhanced uniform illumination and weather proof gasket for lamp & driver compartment, Heat resistance toughened glass fitted with silicon gasket for IP 66 protection in cast aluminium housing with SS screws fixed on existing bracket & connecting, including taking down old light fitting of any description complete all as specified and directed.

S&F LED FLOOD Light fitting 210 watt, system efficiency not less than 100 lumen / watt, IP66 protection, consisting of high / low voltage cut off, maintenance free isolated Electronic driver circuits, Low THD, PMMA grade high quality Transmittance lens, Epoxy powder coated Die Cast Aluminium housing with unique lens system for enhanced uniform illumination and weather proof gasket for lamp & driver compartment, Heat resistance toughened glass fitted with silicon gasket for IP 66 protection in cast aluminium housing with SS screws fixed on existing bracket & connecting, including taking down old light fitting of any description complete all as specified and directed.

Taking down carefully (copper/aluminium ) submain wiring complete of any type (batten/surface conduit or concealed ) for socket point or power point complete with all fittings such as swiches sockets pendants etc complete and making good disturbed surface of wall,floor or ceiling with plaster of tiles or roof treatment etc and finishing the surface with distemper white washing/colour washing to match with the existing surface complete all as specified and directed

M&L for sub main wiring using PVC insulated and unsheathed multistranded FRLS copper conductor cable using approved colour code as per IS drawing in and incl PVC casing and capping with all accessories and making good disturbed surfaces of wall, floor or ceiling with plaster and finishing the surfaces with distemper/white washing/colour washing to match with the existing surface complete as specified and as directed by Engr-in-charge of the following sizes of cables.

Using two single core PVC insulated FRLS cable 4 sqmm copper conductor multi stranded and 4.0 sqmm copper conductor insulated cable using as earth wire. Note :2 runs of 4sqmm copper cable & 1 run of 4.0 sqmm copper cable in and including 20mm PVC conduit shall be measured as one unit

Using two single core PVC insulated FRLS cable 2.5 sqmm copper conductor multi stranded and 2.5 sqmm copper conductor insulated cable using as earth wire. Note :2 runs of 2.5sqmm copper cable & 1 run of 2.5 sqmm copper cable in and including 20mm PVC conduit shall be measured as one unit

Material and labour for renewal of earthing complete with galvanized iron earth plate electrode 600 mm x 600 mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below normal ground level) with top edge of the plate not less than 1.5 m deep below normal ground connected to galvanized steel wire 4 mm dia by means of bolts nuts check nuts and washer of galvanized steel, watering pipe of 20 mm bore, galvanised iron, medium grade, and 15 mm bore galvanised iron light grade for earth wire protection including all excavation earth work in any type of soil, PCC pit in PCC 1:2:4 type B-1 and RCC 1:2:4, type B1 for precast chamber cover 50 mm thick, reinforced with welded steel wire fabric or XPM Jali (weight not less than 4.00 Kg / sqm) with cast iron frame, with charcoal, salt, funnel complete all as shown in the electrical plate No 3 of SSR part-I and testing on completion. Note:- Quoted rates shall be deem to include for earth wire with protection pipe up to 7.5 M length

S&F in repairs pole mounted junction box (Street light boxes) weatherproof cabinets IP -65-IK-09 class II with removable chasis and faceplates,lockable door handle, sealable cover, self extinguishing conforms to EN 60439-3, for single phase lighting system, suitable for 6 module with 1 row complete all as specified and directed.

S & F in repairs contactor 25A 2NO , suitable for 230V AC complete all as specified and directed.

S & F in repairs MCB DP 32A DX3 DP , suitable for 230V AC complete all as specified and directed.

Supply, fix in repair digital weekly timer Switch of supply voltage 240vAC, 50/60 HZ complete all as specified and directed.

Supply and fix in repair LED 5 Watt Round ( Warm white) spot light based down lighter 24 V complete with inbuilt driver, 50 HZ T-35 'C', 63000 K complete all as specified and directed.

S & F in repair LED round spot light 3 W ( Warm white) capacity, CCT :- 3000 K, working voltage level 220V-240V complete all as specified and directed.

S & F in repair LED round spot light 2 W capacity, CCT :- 3000 K, working voltage level 220V-240V, complete all as specified and directed.

S & F in repair LED panel Light Round type 15 watt (warm white) capacity complete all as specified and directed.

Supply and fix in repair LED 10 Watt round panel light fitting (warm white) 240 V 50 HZ with inbuilt driver mechanism complete all as specified and directed.

S & F in repair LED candle 6watt (E14 cap) warm white complete all as specified and directed.

S &F in repair LED candle 3watt (E27 cap) warm white complete all as specified and directed.

S &F in repair LED bulb 12watt, 230 volts suitable for threaded/pin type holder fitment (warm white) complete all as specified and directed.

Supply and fix LED decorative post of lantern for 360degree indirect light with IP 65 protection , glare free and better uniformity light , cap 40 Watt fittings including all accessories complete fixing accessories fixed in position complete all as specified and directed.

Supply and Fix LED Bollard light fitting 9/10 watt (Warm white/white), inbuilt driver mechanism, robustly designed, IP 65/IK10 protection complete with base plate and provision of wire 2.0m copper conductor from fitting to connection point incl taking down old unsv light fitting complete all as specified and directed.

M &L for servicing/cleaning/maintenance of water fountain by bailing out unclear water and cleaning of tiles inside and outside using suitable descaling agent and allowing fountain to become wet, minor repair to pipe and nozzles, gate valves and other connected accessories incl minor repair to under water motor and electrical connection complete all as specified and directed.

M&L for repairing / servicing the monoblock pump set of capacity 3 to 5 HP by dismantling the pump and motor, over hauling of pump by replacing the complete worn out parts such as cast iron impeller, bearing, water seal, repairing the shaft by machining, welding, grinding, polishing etc, including servicing of electric motor suitable capacity with replacement of wornout bearing for driven and non driven ends, reassembling the pump and motor after complete servicing and repair and testing on load complete all as specified and directed.

Supply and Fix non integral LED flexible strip light with high brightness for outdoor applications suitable for 15 watt, 4000K, 230 volts complete with fixing arrangement incl taking down old unsv strip complete all as specified and directed.

M&L for dismantling of existing defective induction motor of capacity 3 to 5 HP, three phase, 415 V, 50 Hz, from the foundation, disconnecting the electric connection, coupling pulley, cutting down and removing existing burnt out copper windings, cleaning of slots and rewinding with super enamelled solid copper conductor (winding wire) of suitable gauge and size complete including varnishing, drying, ovening, overhauling, greasing and fixing in the same position, making necessary electric connection and testing of induction motor complete all as specified and directed.

Supply and fixing in repair recess mounted LED luminaire with full diffuser 36 watt of 2x2 grid for new age work space, powder coated luminaire with minimum 100lm/watt efficiency, 25000 to 50000 working hours and 6500CCT complete all as specified and directed.

Supply and fix in repair round recess mounted LED luminaire with full diffuser 15/16 watt suitable for opearting voltage 220-240VAC and inbuilt driver, powder coated luminaire with minimum 100lm/watt efficacy ,25000 to 50000 working hours and 6500CCT complete all as specified and directed.

Supply and fix in repair recess mounted LED slim downlight square luminaire with full diffuser 18 watt suitable for opearting voltage 220-240VAC and inbuilt driver, powder coated luminaire with minimum 100lm/watt efficacy, 25000 to 50000 working hours and 6000CCT complete all as specified and directed.

Supply and fix in repair LED power supply driver suitable for Primary:220-240 VAC, 50/60Hz 0.14A suiatble for 18watt LEd downlighter Secondary: constant current DC:300mA with thermal,overload and short circuit protection complete all as specified and directed.

Supply and fix in repair LED power supply driver suitable for Primary:220-240 VAC, 50/60Hz 0.055 -0.080A suiatble for 16watt LED downlighter Secondary: constant current DC:300mA with thermal, overload and short circuit protection complete all as specified and directed.

Supply and fix in repair LED power supply driver suitable for Primary:220-240 VAC, 50/60Hz suiatble for 36watt (2x2 grid) LED recess mounted fitting Secondary: constant current DC:300mA with thermal, overload and short circuit protection complete all as specified and directed.

Supply and fix in repair LED power supply driver suitable for Primary:220-240 VAC, 50/60Hz suiatble for 9/10watt LED bollard fitting Secondary: constant current DC:300mA with thermal,overload and short circuit protection complete all as specified and directed.

Supply and fix in repair round recess mounted LED slim luminaire with full diffuser 24 watt suitable for opearting voltage 220-240VAC and inbuilt driver, powder coated luminaire with minimum 100lm/watt efficacy, 25000 to 50000 working hours and 6000CCT complete all as specified and directed.

Supply and fix in repair LED power supply driver suitable for Primary:220-240 VAC, 50/60Hz suiatble for 24watt slim downlighter Secondary: constant current DC:300mA with thermal, overload and short circuit protection complete all as specified and directed.

Supply and fix in repair LED power supply driver suitable for Primary:220-240 VAC, 50/60Hz suiatble for 40watt post top fitting Secondary: constant current DC:300mA with thermal, overload and short circuit protection complete all as specified and directed.

Supply and fix in repair wall mounted Cabinets Made with Metal Textured polyester coating providing excellent corrosion and scratch resistance front door Openable along with inbuilt accessories made as per IP- 55 standard along with (a) inbuilt one two pole contactor of 25 Amp rating make BCH Cat part No :- CPG 216, (b) one nos 32 Amp two pole MCBs (c) one No 32 amp single pole MCB, the box size will be 200 mm x 200mm x 120 mm ( H X W X D) BCH cat No :- BIL - 50000 (d)Digital timer clock type 110-240 VAC 1 C/O Base/DIN 25 ON/OFF complete all as specified and directed.

S & F brass nozzle 25mm tulip / foam jet nozzle threaded with suitable size packing and washers for fountain complete all as specified and directed.

S & F Brass mist nozzles , double threaded socket and washer with suitable size packing and washers for fountain complete all as specified and directed. Note: (i) The size of nozzle shall be as per site requirement. (ii) Contractor shall submit design and get it approved by Engr-in-charge.

S&F butterfly valves of size 40 mm bore ISI marked with iron wheel head screwed both ends for iron pipe and fixed, complete all as specified and directed.

Supply and fix LED decorative post of lantern 45 Watt fittings including all accessories complete fixing accessories and clamp including 4 metre height black painted glavanized pole, fixed in position including necessary PCC work and execavation as per manufactuer's instruction complete all as specified and directed.

DWARKADHISH ENTERPRISE (BID ID -3112139)

Pooja Enterprise (BID ID -3115246)

SURESH ELECTRICALS (BID ID -3115165)

jagdish machinery stores (BID ID -3114892)

M/s super construction (BID ID -3115272)

Krishna Bhoomi Enterprise (BID ID -3115334)