COMPREHENSIVE BR MAINT WORKS IN ZONE II AT LANSDOWNE.

Taking down chowkhats or frames of any description with shutters (without taking off shutter from the frames) exe 1.5 Sqm but not exceeding 4.0 Sqm each complete all as specified and as directed.

Taking down chowkhats or frames of any description with shutters (without taking off shutter from the frames) not exceeding 1.5 Sqm each complete all as specified and as directed.

Taking down wooden shutters of any description exc 1 Sqm but n. exc 2 sqm each and removing to store complete all as specified and as directed.

Demolition of brickwork or stone boulder masonry built in cement mortar including all quoins, arches, pillars etc complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n. exc 15 cm thickness (below or above ground level )and removing unserviceable material,outside cantt area complete all as specified and as directed.

Demolition of stone slab and tiles of any description or thickness in floors, laid bedded and pointed in any mortar aprons complete all as specified and as directed.

Dismantling plain or corrugated steel sheeting , any gauge thickness including Nanital or similar pattern roof covering complete all as specified and as directed.

Dismantling ballies, hard or soft wood, any position except in post and struct including taking out iron scraps, bolts and nuts etc if any type -I complete all as specified and directed.

S&F for Joist, channel, angle, or tee sections,fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) confirming to Fe 410W(Gde-E-250 Quality) complete all as specified and as directed.

M&L for cement concrete type B-2 (1:2:4) (40 mm graded aggregate) as in foundation filling and mass concrete complete all as specified and as directed.

S&F Pre-painted galvatume aluminium zink coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed self tapping screws complete all as specified and as directed.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa (AZ 150) as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and as directed.

M & L for pre polished 18-20mm thick Granite slab white and black table rubbed in cooking plateforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match incl rounded exposed edge complete all as specified and including directed.over 20 mm thick screed bed in CM 1:6 complete all as specified and directed.

S & F 35mm thick factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moistur proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer- In- Charge. Note: stainless steel butt hinges and necessary S.S screws shall be paid separately.

S&F Factory made double rebate WPC (wood polymer composite) solid door frames/chowkat of size 65x125 mm (double riveted of virgin PVC Polymer of K value 58-60(Suspension Grade) calcium carbonate and natural fibres (wood/powder/rice husk/wheat husk ) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threated star heads SS screw having minimum frame density of 750 kg/cum screw withdrawal strenght of 2200 N (face) and 1100 N (Edge)proof, water/moisture proo, minimum compressive strenght of 58 N/mm2, modules of elasticity 900 N/mm2 and serestance to spread of flame of Class A category with property of being termite/borer proof, water / moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge.

S & F 30 mm thick factory made single extruded WPC (Wood Polymer Composite) solid flush SKELTON door shutter comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moistur proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer- In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)

S & F Butt hinges, 100 mm long extruded brass, with mild steel hinge pin, bright polished and fixed heavy duty, type B-11 complete all as specified and as directed.

S & F 250mm long mild steel sliding door bolts, stove enamelled mild steel anodised sliding door bolt with hasp staple, bolt type, and fixing clips of sheet, cast or extruded sections & fixing bolts and sliding bolts of extruded section or cast aluminium alloy, ISI marked complete all as specified and as directed.

S & F 150mm long, aluminium anodised, barrel tower bolts, of extruded section ISI marked complete all as specified and as directed.

S & F Aluminium handles cast type anodised of size 150mm long ISI marked complete all as specified and as directed.

Supply only stainless steel wire cloth 0.56 mm nominal dia of wire and avarage width of aperature 1.18 mm dia complete all as specified and as directed.

Supply only 4.00 mm thick sheet glass, ordinary quality and fixing with aluminium door and windows in square not exceeding 0.5 square metre in each pane complete all as specified and as directed.

M&L Brickwork with sub class ‘B’ (old size) bricks, straight or curved on plan exceeding 6 metre mean radius built in cement sand mortar 1:4 complete all as specified and as directed.

M & L for providing 75mm thick PCC (1:3:6) type C-2 using 40mm graded stone aggregate as in plinth protection and similar works including finishing the surface of concrete topping even & fair, without using extra cement complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing rubbish off premises complete all as specified and as directed.

M&L for joint free , Non- skid coloured ceramic tiles 7 to 8 mm thick area of each tile exe 0.18 sqm but not exe 0.38, as in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match incl 10 mm thick rendering in CM 1:6 Set and jointed in neat cement slurry complete all as specified and as directed.

M&L glazed ceramic tiles in vertical surface 450x350x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over 15 mm thick rendering (1:6) complete all as specified and as directed.

Taking down cement plaster of any description including raking out joints, hackisng for key, scrubbing down with water etc complete all as specified and as directed.

Material & labour for Rendering 15 mm thick CM 1:6 on brick or concrete surfaces finished even & smooth without using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick in two coats i.e. 10mm thick in CM 1:6 and 5mm thick in CM 1:4 using water proofing liquid compound as per manufacturer's instructions complete all as specified and as directed.

Supply only liquid water proofing compound complete all as specified and as directed.

M&L for preparation of newly plastered surface of external wall all as prescribed by manufacture of paint and applying two coats of exterior anti fungal acrylic emulsion paint (walmista of Berger paint or equitant in Asian paint, Nerolac etc over one coat of primer complete all as specified and as directed.

M&L for preparation of newly plastered surface of internal wall by application of wall care putty to remove the dent and to make the surface even and smooth by grinding or rubbing with sand paper and applying two coats of distemper oil emulsion over a coat of primer using roller all as specified and prescribed by manufacture of paint complete all as specified and as directed.

Dismantling of water tanks exc 500 ltr capcity but n exc 1000 ltr complete all as specified and as directed.

S&F 1000ltr capacity rotational moulded polyethylene water storage tanks triple layered white (cylindrical vertical with closed top) hoisted and fixed in position and including 20 mm dia ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plasttic ball screwed for iron pipe and fixed (Minimum weight 15mm-142gms/2.0mm-455gms/40-690gms), complete all as specified and as directed.

S&F in repair Stop valve 20mm dia bore,cast copper alloy, screwed down, high pressure, with crutch or butterfly handle,screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed.

S&F in repair vitreous china squatting pan 'orissa pattern 580 mm X 440 mm white with integral foot rests (excluding flushing cistern and flushing pipe but incl fixing complete all as specified and as directed.

S&F in repairs PVC valveless, syphonic action type flushing cistern (Dual action ISI Marked), low level , white, with inlet ball valve, float and handle including brackets and flush pipe suitable for IWC of polyethylene of low or high density complete all as specified and as directed.

S&F in repair Vitreous china wash hand basin in repair ,white ,flat back of size 550x400mm with PVC connection (15x450)mm long with PTMT nuts and PVC washer and including cutting for pinning in ends,pair of cast iron brackets and provision of PVC waste pipe 32mm of adequate length , waste coupling 32 mm dia of PTMT half or full threaded Min wt 45 gram, complete all as specified and as directed.

S&F in repair PVC pipe 32/40 mm dia as in waste pipe to sink complete all as specified and as directed.

S&F in repair CP Brass Tubular towel rail 20mm dia D-type 60 cm long between flanges, including brackets and fixed to walls, complete all as specified and directed.

S&F in repair PVC connection 15 mm size, of length 450 mm, with PTMT nuts supplied and fixed in repairs complete all as specified and as directed.

S&F in repair 15 mm Steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings(such as bends, elbows, Tee short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore 15mm, complete all as specified and as directed.

S&F in repair Steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings(such as bends, elbows, Tee short pieces, connectors, back nuts, diminishing pieces, caps and plugs,unions etc.) of nominal bore 20mm, complete all as specified and as directed.

Supply only Pillar tap 15 mm dia fancy type, cast copper alloy, with capstan heads, chromium plated screwed down high pressure with or without lettered Hot or Cold with scrwed shanks and fly nuts, screwed for iron pipe and fixed make seiko complete all as specified and directed.

S&F in repair 15mm Bib tap fancy type cast copper chromium plated alloy with capstan handle screwed down screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed.

S&F in repair Stop Angle valve cast copper alloy chromium plated 15mm dia, screwed down, high pressure with capstan handle, screwed both ends for iron pipes or for unions and fixed complete all as specified and as directed.

S & F in repair sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to waste pipe, overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F for Providing and fixing windows & ventilators fabricated from Rolled Formed GI Section made of Galvanised steel colour coated(PPGI Sheets) (Base steel as per IS 513 ‘’D’’ quality. Galvanised as per IS 277 with Zinc of 90 Gsm/SqMt w. PAINT: Pre-Painted sections should be with primer coat of epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer of 5-7 microns or powder coated with pure polyester powder upto 50-60 microns thick.GI Section of 0.58mm thick in Double rebate windows in which both glazed shutter and flymesh shutter, 74 X 60mm outer frame , Mullion 72 x 49mm, Glazed shutter 48 x 22mm, Flymesh 41 x 22mm, Beading with round ends for Glass Fixing 12 x 12mm in fixed portion and the outer frame and mullions to have rebate for glazed/gauzed shutters the sections cut to length metre joined with corner PolyVinylChloride brackets centre mullion fixed with PolyVinylChloride Mullion caps . Glass of 4mm thick plain float glass fitted with Ethylene Propylene Diamine Monomer in glazed shutter and wiremesh of Stainless steel of 36 guage to fix mesh in mesh shutter using VC Black Gypsum Drywall screws and Spoon profile of 0.58mm GI Sheet. Corners of the windows should be joined with corner brackets made of polyvinylchloride with crca of zinc phosphate coat.Each glazed shutter and fly mesh shutter shall be provided with SS Pivot Hinges 2 in each, PolyVinylChloride handle 1 in each and Powder coated Peg stay in Glass shutter.Window shall be provided with Powder coated MS Grill/Guard Bars made of 10mm MS Sq Bar welded to 6 x 12mm MS Flat with countersunk holes at both vertical ends . Gap between the bars should not be more than 150mm . Window frames shall be fixed to brick / concrete masonry by using nylon self expension caps & 75/100 mm MS screws after drilling in walls. VC Black Gypsum Drywall screws should be used while fixng corner brackets,stay,hinges,mullion caps of windows.

Please Enable Macros to View BoQ information