Infrastructure Development Project for Establishing Modern Training Infrastructure at State Forest Training Institute Walayar, under NABARD-RIDF Tranche XXX

ESTABLISHING MODERN TRAINING INFRASTRUCTURE AT SFTI WALAYAR - ACADEMIC BLOCK

Academic Block Civil Works

50.2.25.1 Filling with contractor's own earth ( excluding rock) in trenches, plinth, sides offoundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m as per directionof site Engineer-in-charge

2.31 Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees andsaplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared

2.8.1 Earth work in excavation by mechanical means (Hydraulic excavator) /manual meansin foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan),including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed,within a lead of 50 m.All kinds of soil

2.6.1 Earth work in excavation by mechanical means (Hydraulic excavator)/manual meansover areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan)including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5m, as directed by Engineer-in-charge.All kinds of soil

2.26.1 Extra for every additional lift 1.5 m or part there of in excavation/ banking excavatedor stacked materials.All kinds of soil

2.25 Filling available excavated earth (excluding rock) in trenches, plinth, sides offoundation etc. in layers not exceeding 20 cm in depth, consolidating each depositedlayer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

51.2.3 Filling with Quarry Muck Filling up low lying and water logged areas with localmaterial/ quarry muck, spreading in layers, leveling the top at site and consolidation by ramming, etc complete for improving the CBR value of subgrade

4.1.8 Providing and laying in position cement concrete of specified grade excluding thecost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources

4.1.5 Providing and laying in position cement concrete of specified grade excluding thecost of centering and shuttering - All work up to plinth level:1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources)

4.1.3 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-III)derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

60.7.1 DRY RUBBLE MASONRY _ Dry rubble without concrete levelling course masonry with good quality blasted rubble including packing to compactness to lines and levels cost and conveyance of all materials labour charges etc. complete as per direction of Departmental officers at site

7.1.1 Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand

5.1.2 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size derived from natural sources)

5.22.6 Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth level Thermo - Mechanically Treated bars of grade Fe-500D or more

5.9.1 Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.7 Centering and shuttering including strutting, etc. and removal of form for:Stairs, (excluding landings ) except spiral - staircases)

5.2.2 Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up tot floor five level excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

26.30.1 Drilling suitable holes in reinforced or plain cement concrete with power driven drill machine to a minimum depth of 100mm upto 200mm in RCC beams, lintels, columns and slabs to introduce steel bars for sunshades/balconies including fixing the steel bars in position using epoxy resin anchor grout of approved make but excluding the cost of reinforcement, all complete as per direction of Engineer-In-Charge.Upto and including 12mm dia.

5.3 Reinforced cement concrete work in beams, suspended floors, roofs, having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with1:1.5:3 (1 cement : 1.5 coarse sand (Zone III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources).

5.22A.6 Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo - Mechanically Treated bars of grade Fe-500D or more

5.9.6 Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts

5.9.5 Centering and shuttering including strutting, etc. and removal of form for:Lintels,beams, plinth beams, girders bressumers and cantilevers

5.9.3 Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.9.16.1 Centering and shuttering including strutting, etc. and removal of form for: Edges of slabs and breaks in floors and wallsUnder 20 cm wide

5.9.19 Centering and shuttering including strutting, etc. and removal of form for:Weather shade, Chajjas, corbels etc., including edges

5.11.1 Extra additional height in centering, shuttering where ever required with adequate bracing, propping etc. including cost of de-shuttering and decentering at all levels,over a height of 3.5m, for every additional height of 1 metre or part thereof (Plan areato be measured).Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)

5.30 Add for plaster drip course / groove in plastered surface or moulding to R.C.C. projections.

4.11 Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20mm nominal size derived from natural sources).

4.17 Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarses and (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brickballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

50.6.2.1 Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x15 cm or nearest available size confirming to IS 2185 part I of 1979 for foundation and plinth with thickness 15cm in: CM 1:6 ( 1 cement :6 coarse sand) etc complete

50.6.1.5 Solid block masonry using pre cast solid blocks ( Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 Part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement : 6 coarse sand) etc complete

50.6.2.2 Solid masonry using pre cast solid blocks (factory made) of size 30x20x15cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level with thickness 15cm in : CM 1:6 ( 1 cement : 6 coarse sand) etc complete

50.6.3.2 Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x10 cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level for 10 cm thick wall in : CM 1:6 ( 1 cement : 6 coarse sand) including cost of scaffolding complete

6.47 Providing and laying Autoclaved Aerated concrete (AAC) blocks masonry 150mm/230mm/300 mm thick with Grade- I AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).

6.15 Extra for providing and placing in position 2 Nos 6 mm dia M.S bars at every third course of half brick masonry

OD76457/2025-2026 Supplying & fixing alkali-resistant fibreglass mesh 110GSM toimprove elogation at failure and crack-bridging on horizontal surfaces as per the manufactures specifications size of mesh 5x5 mm. Weight of raw mesh - 100 g/m2

13.1.1 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

13.8.1 15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix:1:3 ( 1 Cement : 3 fine sand)

13.16.1 6 mm cement plaster of mix:1:3 ( 1 cement : 3 fine sand)

13.7.1 12 mm cement plaster finished with a floating coat of neat cement of mix:1:3 ( 1 cement : 3 fine sand)

13.18 Neat cement punning

13.30 18 mm thick moulded cement mortar band in two coats under layer 12 mm thick with cement mortar 1:5 ( 1 cement : 5 coarse sand) top layer 6mm thick with cement mortar 1:4 ( 1 cement : 4 fine sand).

13.76 Forming groove of uniform size from 12x12 mm and upto 25 x 15 mm in the top layer of washed stone grit plastered surface as per approved pattern, including providing and fixing aluminum channels of appropriate size and thickness (not less than 2 mm), nailed to the under layer with rust proof screws and nails and finishing he groove complete as per specifications and direction of the Engineer -in-Charge..

2.34.1 Supplying chemical emulsion in sealed containers including delivery as specified.Chlorpyriphos / Lindane emulsifiable concentrate of 20%

2.35.3.1 Diluting and injecting chemical emulsion for POST -CONSTRUCTIONAL antitermite treatment (excluding the cost of chemical emulsion): Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floor:With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

10.17 Providing and fixing M.S. fan clamp type I or II of 16 mm dia M.S. bar, bent to shape with hooked ends in R.C.C. slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete.

9.1.1 Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).Second class teak wood

OD76460/2025-2026 Supplying and fixing pressed steel DOOR of standard pattern with frames as per profile of IS4351 sections 105x60 mm using 18G(1.2mm thick GI sheet and shutters made of section 75x30 cm outer styles and horizontal members and with enclosed and stiffened as per specification including all fittings such as tower bolt etc. complete

9.7.7.1 Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured), Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick:4 mm thick glass pane (weight not less than 10kg/sqm).

9.7.7.2 Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured), Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick:5.0 mm thick glass panes (weight not less than 12.50 kg/sqm).

9.147A.2 Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 +/- 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Casement window double panels with S.S. friction hinges (300 x 19 x 1.9 mm) made of (small series) frame 47 x 50 mm, sash 47 x 68 mm & mullion 47 x 68 mm all having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area of window above 0.75 sqm upto 1.50 sqm).

9.147A.3 Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 +/-0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Casement window double panels with top fixed with S.S. friction hinges (350 x 19 x 1.9 mm) made of (small series) frame 47 x 50 mm, sash 47 x 68 mm & mullion 47 x 68 mm all having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. ( Area of window upto 2.50 sqm).

9.147B.1 Providing and fixing factory made uPVC white colour fixed glazed windows/Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.)

21.3.2 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5.50 mm thickness (weight not less than 12.50 kg/sqm)

21.3.1 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm)

9.53 Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

9.71.1 Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc. complete:125x64x2.50 mm

9.70.2 Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete:100x58x1.90 mm

9.70.4 Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete:50x37x1.50 mm

9.71.3 Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc. complete:75x50x2.50 mm

9.135.2 Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.50 mm all complete.With 12 mm mild steel U beading

9.148.2 Providing and fixing stainless steel (SS-304 grade) friction hinges to the side/ top hung uPVC windows, of approved quality, with necessary stainless steel screws etc. as per direction of Engineer - in-charge.250 x 19 x 1.9 mm

9.151 Providing and fixing steel roller for u PVC sliding window with necessary screws etc.complete.

9.165.2 Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete.100mm

9.84 Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width form 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

9.102 Providing and fixing aluminium casement stays, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

9.165.1 Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete.125 mm

OD76468/2025-2026 Providing & Fixing High -quality stainless steel sliding door bolts of approved brand & manufacturer with nuts and screws etc complete. Size -15x12x10cm/ nearest available size, weight carrying capacity- not less than 30Kgs.

OD76470/2025-2026 Providing and fixing Stainless steel tower bolts 250x10mm with necessary screws etc, hardness-grade 10.9, thread style- right hand, weight-345grams. complete.

9.113 Providing and fixing bright finished 100 mm mortice lock with 6 levers without pair of handles of approved quality for aluminium door, with necessary screws etc complete as per direction of Engineer- in- charge

9.143 Providing and fixing factory made uPVC door frame, made of uPVC extruded section, of size 65 mm x 55 mm with wall thickness 2.0 mm (? 0.2mm), corners of the door frame to be mitred cut and jointed with plastic brackets and stainless steel screws, reinforcing hinge side vertical of the frames with PVC profile of Size 28 mm x 30 mm having wall thickness 2 mm ( ? 0.2 mm), including providing & fixing 3 nos of 125 mm long stainless steel hinges to the frame, fixing the frame with jamb with required number & size of anchor dash fastners, all complete as per manufacturer's specification and direction of Engineer-in-charge.

9.147C.1 Providing and fixing factory made uPVC white colour casement/ Casement cum fixed glazed door comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 +/- 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealent shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Casement door with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 +/- 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.00 sqm).

9.153 Providing and fixing steel (white power coated) crescent lock for u PVC sliding

9.148.1 Providing and fixing stainless steel (SS-304 grade) friction hinges to the side/ top hung uPVC windows, of approved quality, with necessary stainless steel screws etc. as per direction of Engineer - in-charge.200 x 19 x 1.9 mm

9.148.3 Providing and fixing stainless steel (SS-304 grade) friction hinges to the side/ top hung uPVC windows, of approved quality, with necessary stainless steel screws etc. as per direction of Engineer - in-charge.300 x 19 x 1.9 mm

9.149 Providing and fixing casement handle made of zinc alloyed (white powder coated) for uPVC casement window with necessary screws etc. complete.

9.150 Providing and fixing zinc alloyed (white powder coated) touch lock for u PVC sliding window with necessary screws etc. complete

OD76472/2025-2026 Filling the gap between aluminium/stone/wood frame and adjest RCC/Brick/Stone/Wood/Ceramic/Gypsum work by providing weather structure non sag elastomeric Hybrid PU Sealant of approved brand and manufacturer (Asian paints smartcare/Loctite/Dr. Fixit/Equivalent) over backer rod of approved quality as per architectural and direction of Engineer-in-charge complete

50.18.78 Making chases up to 12.5x12.5 cm in walls including making good and finishing with matching surface after housing pipe etc.

Academic Block Finishes

22.5 Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg /sqm mixed with water proofing cement compound @ 0.126 kg/ sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

11.41.2 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600 x 600 mm.

11.49.2 Providing and laying Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS : 15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).Size of Tiles 600x600 mm

11.48.2 Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg). including filling /grouting and finishing complete as per direction of Engineer-in-charge.Size of Tile 600x600 mm

11.41.4 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 1000x1000 mm

11.48.4 Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg). including filling /grouting and finishing complete as per direction of Engineer-in-charge.Size of Tile 1000x1000 mm

11.23.1 Marble stone flooring with 18 mm thick marble stone as per sample of marble approved by Engineer-in-Charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry including rubbing and polishing complete with:Makrana white second quality

11.24 Extra for pre finished nosing to treads of steps of marble stone

11.25 Extra for marble stone flooring in treads of steps and risers using single length up to 2.00 metre.

10.16.1 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes

10.28 Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) Net Total 724.800kg @767.78/k

13.52.1 Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work

8.2.2.2 Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Area of slab over 0.50 sqm

8.4 Extra for fixing marble/ granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete.

8.5 Extra for providing opening or required size & shape for wash basin/kitchen sink in kitchen platform, vanity counter and similar location in marble/granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

9.48.2 Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings/ wooden frames with rawl plugs screws etc

OD76612/2025-2026 Filling Sunken Floors of Bathrooms/toilet with Cement Sand Mixure in the Ration 1:12 including all Charges of Compacting, Conveyances etc. Complete.

22.3 Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C. kitchen and the like consisting of : i) I course of applying cement slurry @ 4.4 Kg/ sqm mixed with water proofing compound conforming to IS: 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. ii) II course of 20 mm cement plaster 1:3 ( 1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. iii) III course of applying blown or residual bitumen applied hot at 1.7 kg per sqm of area. iv) IV course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 Kg/ sqm.

OD76627/2025-2026 Providing and fixing matt finished terracotta clay jali in cement mortar 1:6 (1 cement : 6 coarse sand) used for facades & internal partitions etc., which gives circulation of natural light and fresh air, supporting frame with MS angle/flat, pointing the joints, closing the joints with white cement, rubbing and cleaning to smooth finish etc. As per standard specification.(supporting frame shall be paid additionally)

OD77087/2025-2026 Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 3.25mm thick aluminium composite panel material consisting of 2.25mm thick FR grade mineral core sandwiched between two Aluminium sheets (each0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.s The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete, as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places.

50.9.11.2 Providing and fixing Thomson Multi wood board or equivalent make paneling 18 mm thick, to frame, backing or studding with screws etc. complete (Frames, backing or studding to be paid separately)as per the direction of site Engineer-in-charge.

21.1.1.3 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately): For fixed portionPolyester powder coated aluminium ( minimum thickness of polyester powder coating 50 micron )

25.8 Design supply & installation of suspended Spider Glazing system designed to withstand the wind pressure as per IS 875 (Part-III). The Suspended System held with Spider Fittings of SS-316 Grade Steel of approved manufacturer with glass panel having 12 mm thick clear toughened glass held together with SS- 316 Grade Stainless steel Spider & bolt assembly with laminated glass fins 21 mm thick. The Glass fins and glass panel assembly shall be connected to Slab/beams by means of SS- 316 Grade stainless steel brackets & Anchor bolts and at the bottom using SS channel of 50x25x2mm using fastener & anchor bolts, non staining weather sealants of approved make, Teflon/ nylon bushes and separators to prevent bi-metallic contacts, all complete to perform as per specification and approved drawings. The complete system to be designed to accommodate thermal expansion & seismic movements etc. The joints between glass panels (6 to 8 mm) and gaps at the perimeter & in U channel of the assembly to be filled with non staining weather sealant, so as to make the entire system fully water proof & dust proof. The rate shall include all design, Engineering and shop drawing including approval from structural designer, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. all complete. For the purpose of payment, actual elevation area of Glazing including thickness of joints and the portion of Glass panel inside the SS channel shall be measured

9.105.4 Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with Zinc coating of 120 gms/ (both side inclusive), consisting of floor and ceiling channel 50 mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete.66 mm overall thickness partition using 8 mm thick double skin multipurpose cement board reinforced with cellulose fibre manufactured through autoclaving process (High pressure steam cured) as per IS : 14862 with suitable fibre cement screws

12.53 Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross “T” of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main’T’ at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross ‘T’ of length 600 mm and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved texture in the grid, including, cutting/ making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main ‘T’, bottom exposed with 24 mm of all Tsections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawings and as directed by Engineer-in-Charge.

OD76631/2025-2026 Providing, applying and finishing wall with exterior cement texture paint (Make suzuka Monocrete/equivalent) of required shade. The surface must be flat, clean and smooth. Apply first coat strato primer on wall using roller and let dry for 30min. then apply second layer of strato primer and let dry for 30 min. Sand the entire surface with sand paper in circular motion to ensure the surface is smooth. Apply first coat using scraper ans spatula. dr for 30 min. Apply second coat. The rate including material, labour, conveyance and scaffolding charges.

13.45.1 Finishing walls with textured exterior pint of required shade:New work (Two or more coats applied @ 3.28 ltr/ 10 sqm) over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm

21.18 Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge ( Door handle, lock and stopper etc to be paid separately)

9.84 Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width form 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

21.4.1 Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS: 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors including cost of cutting floors, embeding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer -inCharge.With stainless steel cover plate minimum 1.25 mm thickness

OD77280/2025-2026 Supply and fixing of 400mm long SS-304 Graded Door Handle of 25mm dia, H type of approved brand all complete as per the instruction of engineers in charge

OD77301/2025-2026 Providing and fixing 12 mm thick toughened glass panel of approved brand and manufacture, using patch fittings, sealant, accessories etc as per design. The rate is inclusive of all material cost, labour charge, conveyance etc complete.

13.43.1 Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

13.50.1 Applying priming coat:With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)

13.60.1 Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work

13.61.1 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work

13.80 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

16.3.7 Supplying and stacking at site.Stone screening 11.2 mm nominal size (Type B)

OD77464/2025-2026 Supply and fixing stylish steel door , door leaf thickness 67mm ready available steel thickness 0.90 to 1.20mmx2mmx1.5mm , panel stuffing rock wool/honey comb paper feature multi point multi positin, single key operated lever lock, finishing matt fib=nish heat transmission painting technology (MHTPT) NON DUPLICABLE KEY 8 (3 SERVANT KEYS+ 5 MASTER KEYS)

OD77510/2025-2026 Providing and fixing in position factory made PIR insulated sandwich wall/roof light weight solid core panels. The outer face on both sides of the panels will be pre-coated galvanized steel with 0.35 or 0.45 mm thick each. Panel shall be preferably fixed into 'C' channel made of 50mm size Stainless Steel screwed/fastened to the slab/column/beam etc. The panel shall fix vertically with tongue and groove joint and horizontally locked with steel bar between each. Panels should be used as floor & roofing with additional structural support, steel or RCC depending upon the design. All the operation shall be completed in all respect as per drawings, Manufacturers specifications and under the overall direction of Engineer-in Charge (Cost of all the material is included except "C channel" which will be paid separately).Non load bearing panels 30mm thick of required size

9.70.2 Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete:100x58x1.90 mm

9.71.1 Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc. complete:125x64x2.50 mm

9.70.3 Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete:75x47x1.80 mm

9.114.1 Providing and fixing magnetic catcher of approved quality in cupboard/ward robe shutters, including fixing with necessary screws etc. complete.Triple strip vertical type

9.114.2 Providing and fixing magnetic catcher of approved quality in cupboard/ward robe shutters, including fixing with necessary screws etc. complete.Double strip (horizontal type)

9.116 Providing and fixing sliding arrangement in racks/ cupboards/cabinets shutter by with stainless steel rollers to run inside C or E aluminium channel section ( The payment of C or E channel shall be made separately

9.165.1 Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete.125 mm

9.165.2 Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete.100mm

9.165.3 Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete.75 mm

Plumbing

OD80945/2025-2026 Providing & fixing of white colour ceramic Under Counter Basin of Jaguar/approved equivalent with Fixing Accessories, of size 595 x 420 x 200mm , Bottle trap 32mm size with 300 mm and 190mm long wall connection pipe and wall flange and waste coupling . The rate includes cost and conveyance of all materials, all labour charges etc. complete

OD80952/2025-2026 Providing and fixing Bowl for Coupled WC with PP soft close seat cover, Hinges, Fixing Accessories and Accessories Set of approved brand and manufacturer(Cera/hindware /parryware/equivalent), Size:375x650x770 mm, P trap-180mm, (Model- SLS-WHT-6201/equivalent) Cistern with cistern fittings for 6751S220PP & 6751P180PP/equivalent including cutting and making good the walls and floors wherever required: W.C. pan with ISI marked black solid plastic seat and lid.

OD80954/2025-2026 Providing and fixing curved shaped urinal partition with frosted glass of 8mm thick of size H: 900 W: 450 of Jaguar/approved equivalent

OD80968/2025-2026 Providing and fixing white vitreous china flat back Urinal with Fixing Accessories Size:385x325x635 mm (Jaguar/approved equivalent) standard flush pipe and C.P. brass spreaders with brass unions etc complete.

OD80996/2025-2026 Supplying and fixing in position back coppered mirror (modi float /saint globain/equivalent) 6mm thick of appropriate sizes as per requirement and fixing with 6mm thick multiwood (approved brand as per standards)of the required size of the mirror fixed with silicon sealant etc . complete .The rate including all material cost ,labour charges , conveyance etc complete

OD80997/2025-2026 Supplying and fixing angular stop cock with wall flange jaguar/approved equivalent including cost, fixing charges etc complete.

50.17.1.4 Supplying and fixing CP Health faucet good quality including cost of materials and labour charges etc. complete as per the direction of site engineer-in-charge.

50.17.1.5 Supplying and fixing CP Health Faucet superior quality ( Jagur or equvalent make ) including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.

18.22.2 Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet: 150 mm diameter

18.50.1 Providing and fixing C.P brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.15 mm nominal bore

18.51.1 Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.15 mm nominal bore

18.52.1 Providing and fixing C.P brass stop cock ( concealed) of standard design and of approved make conforming to IS: 893115 mm nominal bore

18.53.1 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS: 893115 mm nominal bore

18.84.1 Providing & fixing chrome plated brass battery based infrared sensor operated pillar cock, having foam flow technology.15 mm nominal bore

OD81015/2025-2026 Providing and fixing Single towel rail of Jaquar/ approved equivalent of 600 mm long stainless steel. The rate includes all material charge, labour charge, conveyance etc. complete

OD81020/2025-2026 Providing and fixing single lever basin mixer without popup waste system with 450mm long braided hoses (Jaguar/approved equivalent) The rate includes all labour charge, fixing charge etc. complete.

OD81054/2025-2026 Providing and fixing SS-304 Grade Anti-Cockroach Floor trap of approved brand and standard size including all cost conveyance etc

OD81056/2025-2026 Supplying and fixing Exposed Part Kit of Concealed Stop Cock & Flush Cock with Fitting Sleeve, Operating Lever & Adjustable Wall Flange with Seal with Regular Body of Concealed Stop Cock Suitable For 20 mm Pipe Line with Protection Cap of jaguar/approved equivalent including cost, fixing charges etc complete.

OD81057/2025-2026 Providing and fixing stainless steel polished mat/glossy finish grating of approved quality and colour Size-150mmx150mm- Drain Size -100x100 mm and deep 80 mm.

17.10.1.1 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required: Kitchen sink with drain board510x1040 mm bowl depth 250 mm

17.28.1.1 Providing and fixing P.V.C. waste pipe for sink or wash basin including PVC. waste fittings complete. Semi rigid pipe 32 mm dia

18.8.2 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.20 mm nominal dia pipes

18.8.3 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.25 mm nominal dia pipes

18.8.4 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.32 mm nominal dia pipes

18.9.3 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineerin- Charge. External work25 mm nominal dia pipes

18.9.4 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineerin- Charge. External work32 mm nominal dia pipes

18.9.5 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threadedfittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineerin-Charge. External work 40 mm nominal dia pipes

18.9.6 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineerin- Charge. External work50 mm nominal dia pipes

18.9.7 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step \CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineerin- Charge. External work65 mm nominal dia pipes

18.17.21 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :32 mm nominal bore

18.17.3 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :40 mm nominal bore

18.17.4 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :50 mm nominal bore

18.17.5 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :65 mm nominal bore

18.19.4.2 Providing and fixing gun metal non-return valve of approved quality (screwed end): 50 mm nominal boreVertical

18.21.2.1 Providing and fixing uplasticised PVC connection pipe with brass unions: 45 cm length15 mm nominal bore

18.49.1 Providing and fixing C.P brass bib cock of approved quality conforming to IS: 8931.15 mm nominal bore

18.65 Providing and fixing PTMT Soap Dish Holder having length of 138 mm, breadth 102 mm, height of 75 mm with concealed fittings arrangements, weighing not less than 106 gms.

50.18.7.6.2 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing . This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 50 mm dia 6 Kgf/cm2 - Internal work- Exposed on wall

50.18.9.10.1 Providing and fixing PVC pipes includings jointing of pipes with one step pvc solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer in Charge. 150 mm dia 6 Kgf/cm2

19.4.1.1 Providing and fixing square-mouth S.W. gully trap class SP -1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 100x100 mm size P typeWith common burnt clay F.P.S. (non modular) bricks of class designation 7.5

50.18.8.6.2 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 50 mm pipe 6 kgf/cm2

50.18.8.7.2 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joint complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc 63 mm pipe 4 kgf/ cm2

50.18.8.8.1 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 75 mm pipe 6 Kgf/cm2

50.18.8.9.1 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chased and making good the wall etc. 110 mm pipe 6kgf/cm2

50.18.9.22.1 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 mm dia Elbow

50.18.9.22.4 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement- 110 mm dia Bend

50.18.9.22.5 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes including jointing with PVC solvent cement 110x110x110 mm dia Tee

50.18.9.22.7 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110x110x75 mm dia Door Tee

50.18.9.22.10 Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement -110 mm dia End Cap

50.18.9.22.12 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110x75 mm dia Reducer

50.18.9.21.7 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75 mm dia Vent cowl

50.18.9.22.8 Providing and fixing PVC moulded fittings /accessories for Rigid PVC pipes, including jointing with PVC solvent cement -110 mm dia Vent cowl

17.22A Providing and fixing CP Brass 32mm size Bottle trap of approved quality & make and as per the direction of Engineer in charge.

17.22B Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge. (a) 15 mm nominal dia

17.2.1 Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:W.C. pan with ISI marked white solid plastic seat and lid

17.7.4 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap

18.48 Providing and placing on terrace (at all floor levels) polyethylene water storage tank :ISI 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

18.48A Providing and fixing rectangular high density polyethylene water storage loft tank with cover, conforming to ISI : 12701, colour of opaque white or as approved by Engineer-in-charge. The rate includes making necessary holes for inlet, outlet & over flow pipes. The base support i/c fittings & fixtures for tank shall be paid separately.

OD81162/2025-2026 Supply & Fixing of brass body nickel plated automatic air release valves with necessary GI Specials, thread, hold tight, brass spindle, NBR and elastomeric, stainless steel spring polypropylene float at the top most points of water supply distribution ring main. 20 mm dia.

OD81170/2025-2026 Providing and fixing of Electric water heater (Geyser) with all controls like Thermostat, pressure relief valve, check valve with CP copper connection pipes wth all flanges of approved make etc. complete. Capacity:3ltr make: cera/vgaurd/equivalent

OD81178/2025-2026 Providing and fixing C.P. brass sink cock (table mounted) with 170mm long swivel spout including cutting and making good the walls wherever required of approved quality. Make Jaquar/ Cera/ approved equivalent.

OD81183/2025-2026 Providing & laying 4 pair 1.5 sq mm cable as control cable of liquid water level controller through an ISI Heavy duty 20mm conduit.

OD81185/2025-2026 Providing & Fixing, testing and commissioning of Automatic Three phase water level controllers with level sensors for submersible pump shall have the following featuresa). Switch off the motor when the water level in tank reaches a preset level below the over flow pipe.b)Switch ON the motor if the water level in tank goes down below a preset value near.c)Switch off the motor in the event of dry running.d)Manual bypass mode.

Electrical

1.10.2 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group B

1.10.3 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group C

1.11 Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.

1.14.1 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2x1.5 sq.mm + 1x1.5 sq.mm earth wire

1.14.2 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

1.14.3 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2 X 4 sq. mm + 1 X 4 sq. mm earth wire

1.14.10 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required4 X 10 sq. mm + 2 X 6 sq. mm earth wire

1.18.2 Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor,unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.2 Pair

1.19 Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

1.21.1 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm

1.21.2 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm

1.24.1 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 amps switch

1.24.4 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.3 pin 5/6 amp socket outlet

1.24.3 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.15/16 amp switch

1.24.5 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.6 pin 15/16 amp socket outlet

1.24.6 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.Telephone socket outlet

1.24.7 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.TV antenna socket outlet

1.25 Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required

1.26 Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

1.27.1 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.1 or 2 Module (75mmX75mm)

1.27.2 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.3 Module (100mmX75mm)

1.27.3 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.4 Module (125mmX75mm)

1.27.4 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.6 Module (200mmX75mm)

1.27.5 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.8 Module (125mmX125mm)

1.28.1 Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.1 or 2 Module

1.28.2 Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.3 Module

1.28.3 Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.4 Module

1.28.4 Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.6 Module

1.28.5 Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.8 Module

90.10.1.2 Supply & Fixing the following types/ sizes of boxes suitable for modular accessories in surface/ recess including making good the damages, colour washing etc as required (RoHS compliant) 2 module moulded plastic box on surface

90.10.1.6 Supply & Fixing the following types/ sizes of boxes suitable for modular accessories in surface/ recess including making good the damages, colour washing etc as required (RoHS compliant) 8 module moulded plastic box on surface

1.31 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings).

1.33 Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required.

1.34 Supplying and fixing brass batten/ angle holder including connection etc. as required.

1.58 Supplying and fixing PVC batten/ angle holder including connection etc. as required.

1.35 Installation, testing and commissioning of wall bracket / ceiling fittings of all sizes and shapes containing up to two GLS/CFL/LED lamps per fitting, complete with all accessories including connection etc. as required.

1.41 Installation, testing and commissioning of pre - wired, fluorescent fitting/ compact fluorescent fitting of all types, complete with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq.mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

1.53.1 Supplying and drawn of UTP 4 pair CAT 6 LAN cable in the existing surface/recessed steel/PVC conduit as required1 run of Cable

1.55.3 Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.Group C

1.56 Supplying and fixing suitable size Gl box with modular plate and cover in front on surface or in recess, including providng and fixing 2 Nos. 3 pin 5/6 A modular socket outlets and 2 Nos. 5/6 A modular switches, connection etc. as required. (For light plugs to be used in non residential buildings).

1.47 Supplying and fixing extra down rod of 10 cm length G.I. pipe, 15 mm dia, heavy gauge including painting etc. as required. (Note: More than 5 cm length shall be rounded to the nearest 10 cm and 5 cm or less shall be ignored)

90.10.3.15 Supply and Fixing the following modular switches & accessories in the existing front plates and giving necessary connections as required (RoHS compliant) 32A DP switch with indicator

90.10.3.33 Supply and Fixing the following modular switches & accessories in the existing front plates and giving necessary connections as required (RoHS compliant )25A 3pin Shuttered socket

90.11.1.11 Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required6 way (8+18) - three phase double cover (IP 42/43)

90.11.1.12 Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required8 way (8+24) - three phase double cover (IP 42/43)

90.11.1.14 Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required4 way (8+12) - double cover TPN vertical DB with provision for fixing 4P MCB / Isolator/ RCCB/ RCBO as incomer and SP/ TP MCB as outgoing (IP 42/43)

90.11.1.15 Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required6 way (8+18) - double cover TPN vertical DB with provision for fixing 4P MCB / Isolator/ RCCB/ RCBO as incomer and SP/ TP MCB as outgoing (IP 42/43)

90.11.1.18 Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required4 way (8+12) - double cover TPN vertical DB with provision for fixing MCCB as incomer and SP/ TP MCB as outgoing (IP 42/43)

90.14.10.3 Supply, conveyance and fixing the following types & current rated control gears & switchgears conforming to IS 13947 suitable for 440 V, 50 Hz, AC supply in the existing panel assembly as required.16 A-100A, 16 kA (Ics=100%Icu), 4 pole, current limiting type MCCB having thermal setting range of 80 - 100% with thermal magnetic release having adjustable OL

2.10.1 Supplying and fixing 5A to 32 A rating, 240/415 volts, 10 kA, ""C"" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

OD81233/2025-2026 Derived From DSR 2.10.4) Supplying and fixing 63 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Triple pole

2.13.1 Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

2.13.2 Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps

2.15.2 Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 milli Amperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps

2.15.3 Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 milli Amperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 amps

OD81915/2025-2026 (Derived from DSR 2.15.3)Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 100 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 amps

2.11 Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

90.12.5.1 Supply & laying of one number PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in the existing RCC/ HUME / STONE WARE/ GI/ DWC pipe as required.2 core 4 sq mm

90.12.5.30 Supply & laying of one number PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in the existing RCC/ HUME / STONE WARE/ GI/ DWC pipe as required.3.5 core 70 sq mm

90.12.7.1 Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.2 core 4 sq mm with factory made clamp

90.12.7.40 Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.4 core 10 sq mm with factory made clamp

90.12.7.30 Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.3.5 core 70 sq mm

90.12.7.41 Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.4 core 16 sq mm with factory made clamp

90.12.7.42 Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.4 core 25 sq mm with factory made clamp

90.12.7.43 Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.4 core 35 sq mm with factory made clamp

90.12.7.29 Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.3.5 core 50 sq mm with factory made clamp

90.12.10.2 Supply & laying of DWC pipe in ordinary soil 0.75m below ground level including excavation50/38 mm or nearest size

90.12.10.4 Supply & laying of DWC pipe in ordinary soil 0.75m below ground level including excavation77/63 mm or nearest size

9.1.23 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 70 sq. mm (38mm)

9.1.32 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 10 sq. mm (25mm)

9.1.33 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 16 sq. mm (28mm)

9.1.34 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 25 sq. mm (28mm)

9.1.35 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 35 sq. mm (32mm)

90.16.1.3 Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required3.15 mm copper conductor ( 10 SWG)

90.16.1.5 Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required4.75 mm copper conductor (6 SWG)

90.16.1.6 Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required6.00 mm copper conductor (4 SWG)

90.16.5.3 Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required.3.15 mm (10 SWG)

90.16.5.5 Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required.4.75 mm (6 SWG)

90.16.5.6 Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required.6. mm ( 4 SWG)

2.10.4 Supplying and fixing 5A to 32 A rating, 240/415 volts, 10 kA, ""C"" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Triple pole

5.4 Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

5.5 Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. (but without charcoal/ coke and salt ) as required.

5.14 Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

5.8 Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

90.4.1 Supply and installation of suitable size MS rod type fan clamp in the RCC slab as per IS 732 as required.

OD81916/2025-2026 Supply, conveyance, installation and commissioning of 5 star rating energy efficient BLDC ceiling fan of approved brand and manufacture (atomberg/Bajaj/Philips /equivalent), power source-corded electric, 1200mm sweep, speed-260rpm, operating voltage- 220V, Wattage-35watts, no of speed levels-6, air flow- min 235 cum/minute, operation control-remote/app/voice, no. of blades-3 nos, LED indicators, timer etc all complete

OD81917/2025-2026 Supply 1200 mm sweep BEE star rated ceiling fan, Features- 230V, no. of blades 3, power consumption- min 50W, air flow capacity-above 210 Cmm, Blade type rust proof /dust proof Aluminium blades, Speed - min 350 RPM, Efficiency Energy Efficient, control type - button control, etc complete as required. (Brand : Crompton / Usha / Orient/ Havells/ Equivalent).

1.44 Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required.

90.4.6 Conveyance, installation, testing and commissioning of wall mounting fans of all types using mounting brackets supplied along with the fan.

90.4.8 Charges for cutting holes suitable for accommodating exhaust fans up to 305mm sweep including plastering colour washing etc. as required.

90.4.10 Conveyance, installation , testing and commissioning of exhaust fans of size up to 450mm in the existing opening, fixing necessary anchor bolts / bolt and nuts etc., as required including giving connections with the supplied wire along with the exhaust fan.

OD81919/2025-2026 Fabrication, Supply, installation, testing and commissioning of 100A LT Main panel board dust tight vermin proof floor/wall mounted cubicle construction with the following:- a) Incoming: 100A ISO - 1no.(Bus bar of air insulated Alu. size as per ISS).b) Outgoing-63A TPN MCCB-3 Nos, 40A TPN MCCB 2nos. Phase indication lamps, MFDM with PF/A/V in the incoming. Earth bus of adequate capacity and double earth connection to all switches, internal rigid connection etc., complete. The board shall be fabricated out of 16 SWG CR sheet and powder coated with shade RAL 7032 after phosphating. (Switchgears L&T, ABB, Schneider)

OD81923/2025-2026 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. LAN socket outlet (RJ-45)

OD81924/2025-2026 Supplying and laying 25mm casing & capping with all accessories as required.

OD81925/2025-2026 Supply and fixing of 20mm dia flexible conduit in wall / suspended from ceiling as required.

OD81926/2025-2026 Supply of 900 or more rpm, 300mm sweep 55 Watts exhaust fan, Body- PVC, suitable for single phase 230V, 50Hz, AC supply, air flow capacity- 1125 Cubic meters/Hr, power source- corded electric with bird guard and other fixing accessories etc. complete as required.

OD81927/2025-2026 Supplying & fixing DP / FP pole sheet steel enclosure on surface / recess for mounting MCB / Isolator complete with connections, testing & commissioning etc. as required.2 / 4 pole enclosure

OD81928/2025-2026 Supplying and fixing 40-63A rating, 240/415 V, 10 kA, C curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Triple pole

OD81929/2025-2026 Supply of 300 mm sweep Wall fan working on 230V single phase A/C and otherfixing accessories etc. complete as required4 X 2.5 sq. mm + 2 X 2.5 sq. mm earth wire

OD81931/2025-2026 Supply and installation of 9/10W B22 LED lamp with 90 lumen/watt in suitable holder with all other accessories etc. as required

OD81949/2025-2026 Supply of Surface mounted 4 feet 18Watts LED linear light with minimum output of 1800 lumens conforming to SELV standards with all accessories as required. Wires/Cables shall be terminated properly as per the standards

OD81950/2025-2026 Supply & Installation of recessed 6 Watts LED round backlit down light with Aluminium housing with minimum output of 600 lumens & 100 lumen/watt, , HEP diffuser, LED CRI>80, CCT 5700 (+/- 300K), L70 50,000 burning hours with valid LM 80, photo biological safety report & LM 79 report, driver with p.f > 0.9 and THD < 15% conforming to SELV standards with all accessories as required.

OD82241/2025-2026 Supply & Installation of recessed 12 Watts LED round backlit down light with Aluminium housing with minimum output of 1200 lumens & 100 lumen/watt, , HEP diffuser, LED CRI>80, CCT 5700 (+/- 300K), L70 50,000 burning hours with valid LM 80, photo biological safety report & LM 79 report, driver with p.f > 0.9 and THD < 10% conforming to SELV standards with all accessories as required.

OD81951/2025-2026 Supply & Installation of Surface mounted 1 feet 5 Watts LED linear light with minimum output of 450 lumens conforming to SELV standards with all accessories as required. Wires/Cables shall be terminated properly as per the standards.

OD81952/2025-2026 Supply and fixing of outdoor decorative bollard luminaire of 800mm height, having efficiency not less than 70 lumen/watt and power consumption of not less than 8W, complete with integral type driver, closed diffuser and mounted using integral base plate in suitable foundation, Shall have IP 65 protection.

OD81953/2025-2026 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings

OD81954/2025-2026 Supply of recessed 33 Watts LED 2x2 direct-indirect backlit light with Aluminium housing & polycarbonate diffuser with minimum output of 3000 lumens & 90 lumen/watt, suitable for low depth ceiling less than 40mm, LED CRI>80, CCT 5700 (+/- 300K), L70 50,000 burning hours with valid LM 80, photo biological safety report & LM 79 report, driver with p.f > 0.9 and THD < 10% conforming to SELV standards with all accessories as required. M.S frame shall be provided if required for POP / Gypsum ceiling.

OD81955/2025-2026 Supply and installation of DIN Rail Surge Protection Device (4+0) Class B & Class C/ Type 1 & Class 2 Tested as per IEC 61643 Part 11:2016 in suitable enclosure. Nominal voltage -230V 50/60Hz, MCOV of 275 V , Total Impulse current-50 KA (10/350? sec) & Total Max Discharge current 200KA (8/20? sec), Voltage protection level <1.5 kV & Residual Voltage @ 5 kA(8/20) <0.8 kV . The Surge Protection Devices should have TOV withstand for 120 Min : 438 V and with out Follow Current & Leakage Current. Protective Elements are High Energy MOV & GDT & the Protection Modes for : L & N to PE . Short- Circuit Current rating (Isccr) ? 25 kA/50 Hz . Back up fuse required more than 160AgG/gL. Health Status Indication required in all cartridge. Total Response time <25 nano sec

OD81956/2025-2026 Supply, installation, testing and commissioning of 63A FP Automatic transfer switch with auto-manual operation and provision for DG start-stop command, utilisation category AC32, phase separator for terminals, Supply/Load - On indication, pad lock for handle operation in suitable enclosure, interconnections etc complete and as required

OD81957/2025-2026 Fabrication, Supply, Installation, testing and commissioning of Meter panel box comprising of following components, 100A TPN SFU, HRC fuse base, 100A HRC Fuse units, neutral links,50 microns powder coated MV panel board 1.6 mm thick over epoxy coated GI support frame etc complete.

OD82127/2025-2026 Preparation of As-fitted drawings, computing the actual connected load, submitting the work completion report, obtaining power allocation & power connection from KSEB. All statutory payments will be reimbursed on production of the original receipts. The rate shall include the charge for preparation of SLD, laminating and displaying it in designated area

1.10.1 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group A

1.55.1 Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.Group A

1.55.2 Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.Group B

1.14.11 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required4 X 16 sq. mm + 2 X 6 sq. mm earth wire

OD82156/2025-2026 Supplying and fixing following rating, four pole, (three phase and neutral), 415 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.

OD82311/2025-2026 Supply & Installation of Surface mounted LED bulkhead having efficacy not less than 66 lumen/watt and power consumption of not less than 9W with high pressure die cast aluminum polycarbonate diffuser with all accessories as required. with IP 65 protection. (Wipro model - LW 07-141 or equivalent)

OD82314/2025-2026 Supplying and fixing 4 pole metal enclosure for UPS incomer and outgoings

OD82317/2025-2026 Supply, installation, testing and commissioning of Floor Mounting Cubical Type Switch Board Panel suitable for 415 V, 3 Phase, 4 Wire 50 Hz AC supply system having sufficient front surface area fabricated in compartmentalized design from CRCA sheet steel of 2 mm thick for frame works, covers and gland plates, cleaning and finishing complete with 7 tank process for powder coating in approved shade, having 125 Amps capacity TPN Aluminium alloy busbars of high conductivity, DMC / SMC / FRP bus bar supports, with short circuit withstand capacity of 31 MVA for 1 Sec., bottom base channel of MS section not less than 100 mm x 50 mm x 5 mm thick, fabrication shall be done in transportable sections, entire panel shall have a common copper earth bar of size 25 mm x 3 mm at the rear with 2 Nos. earth stud, solid connections from main bus bar to switch gears with required size of Aluminium bus bars and control wiring with 1.5 Sq.mm FRLS PVC insulated single core copper conductor cables, cable alleys etc. complete as required. For all MCCBs Ics shall be 100% Icu. The panel shall conform to the Electrical Inspectorate standards and it shall only be manufactured after getting approval from the Engineer-in-charge and the Electrical Inspectorate. BUSBAR 1 Runs of 25 mm x 10 mm Aluminium for each Phase 1 Runs of 25 mm x 6 mm Aluminium for Neutral EB INCOMER SIDE 1 Set - RYB Indication Lamps with Control MCBs 1 Nos - 125A 36kA 4P Thermal Magnetic Type MCCB having 70 to 100% Setting Provision with ROM and Spreader 3 Nos - 125/5A 10VA CL:1 Resin Cast CT 1 Nos - Digital Multifunction Meter measuring V, A, F, KWH, KVA, PF with Control MCBs DG INCOMER SIDE 1 Set - RYB Indication Lamps with Control MCBs 1 Nos - 125A 36kA 4P Thermal Magnetic Type MCCB having 70 to 100% Setting Provision with ROM and Spreader 3 Nos - 125/5A 10VA CL:1 Resin Cast CT 1 Nos - Digital Multifunction Meter measuring V, A, F, KWH, KVA, PF with Control MCBs AUTOMATIC TRANSFER SWITCH 1 Nos - 125A 4P Automatic Transfer Switch with Interlock OUTGOINGS 2 Nos - 100A 25kA 4P Thermal Magnetic Type MCCB having 70 to 100% Setting Provision with ROM and Spreader 2 Nos - 80A 25kA 4P Thermal Magnetic Type MCCB having 70 to 100% Setting Provision with ROM and Spreader 1 Nos - 63A

OD82318/2025-2026 Fabrication, supply & installation of dust and vermin proof, wall mounting, meter box of required size suitable for fixing KSEB meter,fuse units, CT etc, hinged door construction for the front side with compartments if necessary, providing vision panel for the meter compartment, knock out for cable entry and exit including 125A 4 pole Switch disconnector - 1 no, 100A Cut out Fuse - 3 nos, 100/5A, Class 0.5s, 15VA Cast resin CTs - 4 Nos, neutral link etc complete as required at site

OD82320/2025-2026 Supply and providing Aluminium anodised Danger Notice Board of size 200 x 150 mm. with inscriptions (both in English and Malayalam) and conventional Skull and Bone in Red colour at locations as directed by the Engineer in Charge

2.13.3 Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.100 amps

OD82423/2025-2026 supply and providing first aid chart dully framed and placed in a conspicuous location for clear vision. as per standards.

OD82424/2025-2026 Supply and providing ISI marked electrical 1.1 kV grade anti-skid Polyvinyl Chloride (PVC) rubber mat as per IS:15652- 2006 Class A. for the following sizes. 2mx1mx2mm

OD82432/2025-2026 Preparation of all drawings submitting and getting approval from Electrical Inspectorate if required, submitting of Completion certificates and arranging inspection, getting sanction and energisation certificates from KSEB, obtaining power allocation & power connection etc. for commissioning of the whole installation in the premises. All statutory payments remitted for obtaining sanction will be reimbursed on production of the original receipts.

SIGN BOARD

OD77606/2025-2026 Supply and fixing signage for rooms and internal directions. The signage letters will be made with premium quality vinyl sheet of approved colour, pasted on 3mm thick aluminium composite panel backing. The signage will be either fixed on the wall with the screws & double tape or hanged from the false ceiling with the help of hooks & chains complete work.

OD77624/2025-2026 Supply and fixing symbol signage such as No. Smoking, No Spitting, Drinking Water etc. signage of standard sizes as per conventional design/ colour code on 3 mm thick aluminium composite panel. The signage will be either fixed on the wall with the help of screws and double tape or hanged from the false ceiling with the help of chain and screws etc. complete work.

OD77770/2025-2026 Providing and installing in position the following type of sign boards made out of 4mm thick ACP sheet with computer cut with texts written to recommended height in photolumiscent material complete vide technical specifications with mirror fasteners. Sizes, Letter height, Colour, Back ground, language and mounting height of the board shall be fixed at all height/ as per drawing as per design mounted on 2.5cm x 2.5cm size square MS pipe frame

OD77785/2025-2026 Providing and installing in position the following type of sign boards made out of 1.5 mm thick 304 grade stainless steel with computer cut with texts written to recommended height in photolumiscent material complete vide technical specifications with mirror fasteners. Sizes, Letter height, Colour, Back ground, language and mounting height of the board shall be fixed at all height/ as per drawing

10.2 Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

External Works

2.1.1 Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5m in width as well as 10 sqm on plan including disposal of excavated earth up to 50 m and lift up to 1.5 m, disposed soil to be levelled and neatly dressed:All Kinds of soil

2.28.1 Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m.All kinds of soil

2.29.1 Ploughing the existing ground to a depth of 15 cm to 25 cm and watering the same.All kinds of soil

2.31 Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleare

18.9.2 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer in-Charge. External work20 mm nominal dia pipes

18.9.3 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer in-Charge. External work25 mm nominal dia pipes

18.18.3 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete:25 mm nominal bore

30.2.1 Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly levelling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).

30.2.2 Supplying and stacking of good earth at site including royalty and carriage upto 5 k.m. lead complete (earth measured in stacks will be reduced by 20% for payment).

30.2.3 Supplying and stacking sludge at site including royalty and carriage upto 5 k.m. lead complete (sludge measured in stacks will be reduced by 8% for payment).

OD77855/2025-2026 [Derived from 16.68] Providing and laying 40 mm thick natural paving stone made by cutting sandstone/slate/granite/equivalent type of approved size, finished edges, design & shape, laid in required pattern over and including 50 mm thick compacted bed of coarse sand filling the joints by fixing artificial turf of pile ht 40/50mm etc. all complete as per the direction of Engineer-in charge.

16.91.2 Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge.80 mm thick C.C. paver block of M-30 grade with approved color design and pattern.

Upper roof Structure

50.10.1 Steel work in built up G I tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

10.2 Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

8.8.1.2 Providing and fixing expansion hold fasteners on C.C./R.C.C./Brick masonry surface backing including drilling necessary holes and the cost of bolt etc complete. Wedge expansion typeFastener with threaded dia 10 mm

10.16.1 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes

OD77888/2025-2026 Providing and fixing Sandwich Polyurethane Foam (PUF) Panel roofing sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 30 mm thick(PUF panel sandwiched between precoated galvanized iron profile sheet 0.50mm thick top sheet and 0.35mm bottom sheet), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, strength -240 MPA-550MPA, coating mass- AZ 70- AZ 150, Overall density- 40-42 kg/m35-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

OD77894/2025-2026 Supply and Installation of Automatic Whirlybird Non Power Wind Roof Turbine Ventilator, Turbine Material- Stainless steel 304 grade, dia-600 mm, base- 6 core poly-carbonate sheet, No. of blade-36 Nos, type - wind driven, automatic grade- automatic, weight- not less than 5 kgs. etc complete

12.1.1 Providing corrugate G.S. sheet roofing including vertical/ curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete ( up to any pitch in horizontal / vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.1.00 mm thick with zinc coating not less than 275 gm/m2

12.51.1 Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screwscomplete :Ridges plain (500-600 mm)

OD82858/2025-2026 Providing and fixing 200mm wide, 140mm deep 3 mm thick plain UPVC moulded channel type Rainwater gutter pipe of approved brand and manufacturer(aquastar/euroguard/equivalent) with added ribs for extra strength, capacity-20L/m, iron brackets- 900x30x3 mm size @ 0.6/0.7m spacing, bolts, nuts and washers etc., including making necessary connections with rain water down fall pipes etc. complete.4 Kg/cm2

50.18.9.10.1 Providing and fixing PVC pipes includings jointing of pipes with one step pvc solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer in Charge. 150 mm dia 6 Kgf/cm2

50.18.9.18.1 Providing and fixing PVC pipes including fixing the pipe with clamps/clips at 1.00 m spacing. This included jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 75 mm dia 6Kgf/cm2 External work- Exposed on wall

50.18.9.19.1 Providing and fixing PVC pipes including fixing the pipe with clamps/ clips/ at 1.00 m spacing . This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 110 mm dia 6 Kgf/cm2 - External work- Exposed on wall

50.18.9.21.4 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75 mm dia Bend

50.18.9.21.5 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement -75x75x75 mm dia Tee

50.18.9.22.4 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement- 110 mm dia Bend

50.18.9.22.6 Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110x110x110 mm dia Door tee

50.18.9.22.12 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110x75 mm dia Reducer

50.18.9.22.2 Providing and fixing PVC moulded fittings / accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 mm dia 45 degree Elbow

50.18.9.22.8 Providing and fixing PVC moulded fittings /accessories for Rigid PVC pipes, including jointing with PVC solvent cement -110 mm dia Vent cowl

50.18.9.22.10 Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement -110 mm dia End Cap

50.18.9.22.11 Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes,including jointing with PVC solvent cement - 110 mm dia Socket/ coupling

OD83137/2025-2026 supplying and fixing 160 mm dia UPVC half gutter pipe with clamps at 1m spacing including the cost and conveyance of all materials to the site and all labour charges etc. complete 160 mm dia 4 kgf/cm2

9.135.2 Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both

10.25.2 Item Shifted to Sub head 14 as item 14.73 Item Shifted to head 14 as item 14.74 Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

13.52.1 Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work

Septic Tank, Underground Sump, Water Tank

2.6.1 Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.All kinds of soil

2.26.1 Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials.All kinds of soil

4.1.8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

5.1.2 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size derived from natural sources)

5.22.6 Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

5.9.1 Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.3 Reinforced cement concrete work in beams, suspended floors, roofs, having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with1:1.5:3 (1 cement : 1.5 coarse sand (Zone III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources).

5.22A.6 Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo - Mechanically Treated bars of grade Fe-500D or more

5.9.2 Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

13.16.1 6 mm cement plaster of mix:1:3 ( 1 cement : 3 fine sand)

13.9.1 Cement plaster 1:3 ( 1 cement : 3 coarse sand) finished with a floating coat of neat cement.12 mm cement plaster

OD83275/2025-2026 Supply, Installation, Testing and Commissioning of Network Video Recorder Providing & fixing Network Video Recorder 32-channel 720P or 24-channel 1080P high definition network video input and storage Support simultaneous HDMI and VGA output, resolution up to 1920×1080P/60Hz Supports 256Mbps bandwidth throughput handling, Supports 4-channel, 1080P video real-time decoding and synchronous playback.

OD83277/2025-2026 Supplying and drawn of UTP 4 pair CAT 6 LAN cable in the existing surface/recessed steel/PVC conduit as required1 run of Cable Make: Finolex/Dlink/equivalent.

OD83281/2025-2026 Supply, installation, testing and commissioning of indoor IR IP dome camera 2 MP 2.1mm/4mm/6mm focal length lens capable to 1.0 lux sensitivity, with IR n 480 TV lines.

OD83284/2025-2026 Supply, installation, testing and commissioning of indoor IR IP Bullet camera 2 MP 2.1mm/4mm/6mm focal length lens capable to 1.0 lux sensitivity, with IR n 480 TV lines

OD83287/2025-2026 Supply, Installation, testing and Commissioning of HDMI EXTENDER 200 M USB with TCP/IP

OD83297/2025-2026 Supplying and fixing following modular socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.Telephone socket outlet

OD83302/2025-2026 Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor,unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 2 Pair

OD83304/2025-2026 Supply and fixing RJ45 jack with cover , including crimbing/Punching of UTP 4 Pair CAT 6E LAN Cables on both ends with RJ45 Connector

OD83305/2025-2026 Supply and installation of CAT6E 2 mtr long Patch cord factory crimped on both sides

OD83306/2025-2026 Supply, installation, testing and commissioning of 32 inch QHD monitor(2560x1440) of approved brand- LG/Toshiba/Acer/equivalent, Aspect ratio- 16:9, Contrast ration-1000:1, refresh rate-180Hz and 5ms(GTG) response time, Display -LED, Display technology-IPS/VA/Equivalent, view angle-178 degree, image brightness-300 or more, speakers- built-in speakers, finish-matte/glossy, Additional features-HDMI/VGA ports

OD83318/2025-2026 Supply, Installation, testing and Commissioning of Surveillance Hard disk 6TB of approved brand- Seagate/western digital/equivalent, Capacity- 6TB, Hard disk interface-Serial ATA-600/equivalent, Network technology- SATA/equivalent, Product features-portable, rotational speed-5400 RPM, data transfer rate-5 Gigabytes per second, read speed- 180 megabytes per second, media speed-180 MB/s, cache memory installed size- 256, form factor- 3.5 inch.

OD83320/2025-2026 Supply, Installation, testing and commissioning of Cat6 24 Port fullyloaded Patch Panel

OD83322/2025-2026 Supply, installation, testing and commissioning of 16 Port 10/100/1000 Mbps PoE Switch.

OD83332/2025-2026 Supply, Installation, Testing and Commissioning of 8 PORT GIGABIT Unmanaged SWITCH of approved brand and manufacturer-Hikvision, no of ports-8, compatible device- Desktop, switch type- unmanaged, voltage-48Volts(DC), interface-RJ45, data transfer rate- 20Gigabits per second, current rating -2.5 Amps, Dimension-30Lx30Wx5H cm/variable.

OD83333/2025-2026 Supply, Installation, testing and Commissioning of 48 PORT GIGABIT Unmanaged SWITCH (Make: Dlink/equivalent as per approved brand and manufacturer)

OD83486/2025-2026 Supply, installation, testing and commissioning of wall mounted 9Ux500Wx500D With Front Glass Door With Lock & Key,Side Openable Panels with Lock & Key,6Way 5A PDU,1U Cable Manager,Cooling Fan,H/W Kit10

OD83487/2025-2026 Supply, installation, testing and commissioning of 8 Port 10/100/1000 Mbps PoE Switch.(Make: TP-Link/Dlink/equivalent)

OD83488/2025-2026 Supply, installation, testing and commissioning of Telephone distribution box- 50 pair box with lock and Krone modules- approved brand and manufacturer(generic/equivalent), material- powder coated metal.

OD83489/2025-2026 Supply, Installation, Testing & commissioning of Telephone with speaker and caller -id of approved makes - Panasonic/beetal/equivalent, type - corded, mount- desk & wall mountable, including all other accessories for connection.

OD83490/2025-2026 Supply, fixing, testing and commissioning of the Intercom of approved brand and manufacturer- Syntel/Navkar systems/equivalent. with Digital EPABX with PSU, CPU & LINE CARDS, features- 4 co- line + 1 digital Ext +64 extensions (expandable 64 lines 4 trunk), 10000 calls memory, built in 75 internal voice prompts for users help, cable type- ethernet, connector- RJ45, ethernet cable category- cat 6, no of pins-5 or more, model- NEOS 4S/equivalent.

OD83492/2025-2026 Supply, Installation, testing and Commissioning of 5 PORT POE SWITCH of approved brand and ISI certified product.

OD83546/2025-2026 Supply, Installation, testing and Commissioning of 24 PORT GIGABIT Unmanaged SWITCH (Make: Dlink/equivalent)

OD83506/2025-2026 Supply, fixing, testing and commissioning of the WIFI, Access point with 450Mbps on 2.4GHz bandwidth & 867Mbps on 5GHz bandwidth,total of 1317Mbps speed compatable with 802.3af and passive PoE. Centralized Software Controller Monitor and manage hundreds of EAPs in a single or multiple sites.Free cloud access to manage from anywhere, anytime.Configure and automatically synchronize unified wireless settings to all EAPs in the network.Secure Guest Network with Facebook Wi-Fi and SMS Authentication

OD83504/2025-2026 Supply, Installation, Testing and commissioning of XLR Connectors of approved brand and manufacturer, ISI certified .

OD83505/2025-2026 Supply, Installation, Testing and commissioning of XLR cable of approved brand and manufacturer, ISI certified.

OD83503/2025-2026 Supply and installation of PA Wireless Lapel Microphone Attractive and versatile high performance single channel UHF wireless microphone available in different frequencies. Receiver has built-in 6.3mm (¼?) jack for unbalanced audio output and XLR connector for balanced audio output.

OD83502/2025-2026 Supply and laying of Two Core Speaker Wire 18AWG- Make: RR/Finolex/Havells/equivalent

OD83501/2025-2026 Supply and installation PA Ceiling SPEAKERS 15 WATTS High quality flush mount ceiling speaker with stylish grill and frame of approved brand and manufacturer (Ahuja/equivalent), which integrate wonderfully well with all interiors. Clear and clean sound for speech and music.

OD83500/2025-2026 Supply, installation, testing and commissioning of wall mounted 4Ux500Wx500D With Front Glass Door With Lock & Key, Side Openable Panels with Lock. ISI certified make.

OD83499/2025-2026 Supply and installation of Interactive Intelligent Panel 75 Commercial grade panel), 4K, I5 8th Gen Processor, 8 GB Ram and 1 TB HDD, with 120 GB SSD & Dual OS. Including: Windows License, Easy Capture Software, Easi Talk Classroom Addressing Software, Senses Watch- Classroom Monitoring Software

OD83498/2025-2026 Supply and installation of PA GOOSENECK MICROPHONE with base of approved brand and manufacturer(ahuja/philips/equivalent)

OD83497/2025-2026 Supply and installation of 100 WATTS WITH BUILT-IN DIGITAL PLAYER MEDIUM WATTAGE PA MIXER AMPLIFIER, 3 Mic & 1 Aux Inputs. Built-in MP3 player with remote control for USB, SD/MMC card reader, Bluetooth and FM. Preamplifier Output for connecting to a Booster Amplifier and for recording the programme. Cut & Boost type Bass & Treble controls. Instant transfer to DC power (Car Battery) if AC power fails.

Air Conditioning

OD83556/2025-2026 Supply of 2 TR capacity 5 star Split inverter AC of approved brand (Bluestar/Carrier/Samsung/equivalent), star rating- 5 Star BEE rating, cooling capacity above 6000 W, Power -AC 135-280V, Frequency - 50Hz, display - LED,Compressor- variable type, refrigerant- R-32, Condensing type- full copper (Condenser & evaporator coils), Operating modes-auto mode/ dehumidification/cool mode/turbo mode/sleep mode, Auto re-start type, area coverage -150-200 sqft,air circulation- 700 CFM, Components- wall mounted Air Conditioner unit with Indoor & Out door Split type units with cordless remote,copper wire etc.

OD83558/2025-2026 Supply of 1.5 TR capacity 5 star Split inverter AC of approved brand (Bluestar/Carrier/Samsung/equivalent), star rating- 5 Star BEE rating, cooling capacity above 5100W, Power -AC 230V, Frequency - 50Hz, display - LED, Compressor- variable type, refrigerant- R-32, Condensing type- full copper (Condenser & evaporator coils), Operating modes-auto mode/ dehumidification/cool mode/turbo mode/sleep mode, Auto re-start type, area coverage -150 sqft ,air circulation- 580 CFM, Components- wall mounted Air Conditioner unit with Indoor & Out door Split type units with cordless remote,copper wire etc.

OD83560/2025-2026 SITC of wall mounting type make 4 kVA Voltage Stabilizer designed for Air conditioning load working on 240V, 50Hz Single Phase AC supply to feed output voltage at +/- 10% tolerance with automatic low voltage & high voltage cutoff, built in thermal overload protection, powder coated enclosure etc. complete

OD83561/2025-2026 SITC of wall mounting type 5 kVA Smart Voltage Stabilizer designed for Air conditioning(upto 2 ton AC) load working on 240V, 50Hz Single Phase AC supply to feed output voltage at +/- 10% tolerance with automatic low voltage & high voltage cutoff, built in thermal overload protection, powder coated enclosure. Additional features- digital display, toroidal transformer for stable out, reduced heat & low noise operation etc. complete.

OD83565/2025-2026 SITC of supporting stand / clamp for fixing the AC outdoor unit using suitable support bars /anchor bolts and safety hook up etc. including all accessories etc. complete. MS Angles/flats

OD83566/2025-2026 SITC of Additional flexible PVC control cable of 4C X 2.5 sq mm of approved brans & manufacturer- Sturlite/Anchor/V- guard/equivalent to connect between indoor and outdoor AC units.

OD83567/2025-2026 SITC of Additional flexible PVC power cable of 3C X 2.5 sq mm of approved brand & manufacturer- Sturlite/Anchor/V- guard/equivalent to connect between indoor and outdoor AC units.

OD83568/2025-2026 SITC of Additional 20mm PVC drain piping of good quality to extend water drain connection till nearest silt terminal as required at site. material- flexible heavy-duty extension, tube- multipurpose water in-outlet hose pipe for commercial use (AC units).

OD83569/2025-2026 SITC of additional refrigerant lines (Both suction & discharge) using soft drawn copper pipe of the suitable sizes recommended by the manufacturer for AC units including nitrile rubber thermal insulation of good quality to extend the refrigerant gas connection till outdoor unit as required at site. inner dia 35mm and 9mm thick/nearest available size.

OD83570/2025-2026 Installation, Testing & Commissioning of 5 star inverter type AC units with necessary including fixing of Indoor & outdoor units, necessary gas charging as per manufacturer standards, giving power connection to nearest Power plug point / MCS with 16A plug top, connecting indoor and outdoor units using soft copper refrigerant pipes insulated with nitrile rubber or equivalent material , PVC insulated flexible cable as per original manufacturers standards, drain water provision.

OD83581/2025-2026 Providing and installing in position the following type of sign boards made out of 3mm thick rigid PVC board with computer cut with texts written to recommended height in photolumiscent material complete vide technical specifications with mirror fasteners. Sizes and mounting height of the board shall be as per technical specification. No Smoking sign board 12inch x 4inch.

OD83584/2025-2026 Providing and installing in position the following type of sign boards made out of 3mm thick rigid PVC board with computer cut with texts written to recommended height in photolumiscent material complete vide technical specifications with mirror fasteners. Sizes and mounting height of the board shall be as per technical specification. Fire Exit sign board 12inch x 4inch with arrow markings

OD83585/2025-2026 Supply, installation of in position the signages of "Fire boards approved by Kerala state fire service made out of PVC rigid sheet 3mm thick with computer cut PVC non-reflective self adhesive imported vinyl painted on the front of PVC rigid sheet complete with wall mounting arrangements with mirror screws". with lettering "ASSEMBLY AREA".

OD83586/2025-2026 Supply and providing 6 kg ABC DRY POWDER type fire extinguisher of approved brand and manufacture (Lifeguard/ Eco fire/Safeverse/Equivalent) with Wall hook, Discharge pipe, how to use sticker, expiry date certificate, hose and clamps including fixing it to wall as required

OD83587/2025-2026 Supply and providing 9Litre water type fire extinguisher of approved brand and manufacture (Life guard/ Eco fire/Pyro guard/Equivalent) , Operating temperature- -30 to +60 Celsius, minimum effective discharge-95%, fire rating- 3A, with Wall hook, Discharge pipe, how to use sticker, expiry date certificate , hose and clamps including fixing it to wall as required

OD83588/2025-2026 Supply and providing 9 Litre capacity GI Fire Bucket painted in post office red with primer cost of redoxide and written with white paint 'FIRE' filled with fine sand, mounted on existing MS angle frame work/wall bracket etc as required

OD83589/2025-2026 Supplying, Installing, Testing & Commissioning of 2 way Fire brigade Inlet connection fabricated from 100 mm dia MS Class B medium grade pipe comprising of two 63 mm dia gun metal male threaded non return valve.

OD83590/2025-2026 Supplying, Installing, Testing & Commissioning of Air release valve gun metal body as per IS:778. 20 mm dia .

OD83591/2025-2026 Supplying, Installing, Testing & Commissioning of Hose Box (Fire Hose cabinet) to accommodate one piece of 63 mm dia fire hose along with one piece of 63 mm dia male & female couplings and one branch pipe. The cabinet is made of M.S. powder coated with glass fronted hinged doors and lock.

OD83592/2025-2026 Supplying, Installing, Testing & Commissioning of Hose reel drum made of Mild Steel, with mounting brackets 19 mm dia nylon braded smooth surface rubber thermo plast hose 30 mtrs length with shut off nozzle

OD83593/2025-2026 Supplying, Installing, Testing & Commissioning of Fire Fighting Hose , all synthetic fiber circular woven jacketed,control perculated delivery hose , 38kg/cm2 burst pressure, 22kg/cm2 proof pressure, 14 kg/cm2 working pressure, bearing IS:636-88 type B , in 15 mtrs length, 63 mm dia, duly bounded with SS coupling 63 mm dia pair of male & female parts, instantaneous type .

OD83594/2025-2026 Supplying, Installing, Testing & Commissioning of branch pipe made out of SS 63 mm short male instant. Inlet male threaded outlet, fitting with 15 mm bore nozzle ISI

OD83595/2025-2026 Supplying, Installing, Testing & Commissioning of Hydrant valve 63 mm dia oblique type with SS body & working parts, with instantaneous hose coupling adaptor and PVC blank cap & chain.

OD83606/2025-2026 Supplying, Installing, Testing & Commissioning of Ball Valve as per IS 5312. 20 mm dia

OD83607/2025-2026 Supplying, Installing, Testing & Commissioning of Non Return Valve single plate wafer type slim seal check valve, short pattern type with integral hinge pin disc , nitrile rubber O - ring seat and face sealing as per IS: 5312 .

OD83608/2025-2026 Supplying, Installing, Testing & Commissioning of charges for High Pressure switch arrangement for pump room and total system (model- Danfoss Kp 36/equivalent.), operation- automatic, contact type- normally open, circuit type- 1 way, control- push button, switch type- pressure switch.

OD83609/2025-2026 Supplying, Installing, Testing & Commissioning of charges of Pressure gauge arrangement for pump room and total system (Dia 100mm/nearest available size), material -composite of aluminium, brass, glass, body- metal.

OD83610/2025-2026 Supplying, Installing, Testing & Commissioning of automatic fire hydrant system panel for Terrace pump

OD83611/2025-2026 Supplying and installing of in position the following type of sign boards made out of 3mm thick "Opaque" PVC foam board with computer cut, PVC Non-reflective self adhesive vinyl painted foam board, complete with mirror fasteners.- FIRE ASSEMBLY POINT

OD83612/2025-2026 Supplying and installing of in position the following type of sign boards made out of 3mm thick "Opaque" PVC foam board with computer cut, PVC Non-reflective self adhesive vinyl painted foam board, complete with mirror fasteners. EVACUATION PLAN

OD83613/2025-2026 STATUTORY APPROVAL Complete services from the contractor for Laisoning works such as filing necessary applications, submission of forms for approval to local fire authorities, depositing the fees / other amounts as required for getting the premises / installations, inspected and approved and all other formalities required till approved by Local Fire Authorities. All the expenses incurred in this regard shall be borne by the Contractor. The official payments to be made for any security deposit etc. in this regard which shall be reimbursed on production of original voucher.

OD83614/2025-2026 Supplying, Installing, Testing & Commissioning of electrically operated Terrace Pump of 450LPM capacity 24 MWC, high efficiency volute type with cast iron casing, cast iron impeller, pump coupled with a squirrel cage induction motor TEFC type with a supply condition of 415 V 50 Hz foot mounted type for Suitable 5HP at 1350 RPM 3 kg including base plate coupling guard and all other necessary accessories.

OD83615/2025-2026 Supplying, Installing, Testing & Commissioning of butterfly valve wafer type Stainless steel/SG iron disc , lever operated as per IS:13095 in PN 1.0 , teflon or nylon bushing, nitrile O rings in standard mounting flanges with hand lever type. 110mm dia

OD83616/2025-2026 Under Ground Piping- Supplying, Installing, Testing & Commissioning of underground piping M S pipe Class 'B' medium grade ISI mark complete with all necessary fittings such as nuts & bolts, bends, flanges, tees etc . and piping shall have anti corrosive wrapping treatment. 100 mm dia

OD83617/2025-2026 Above Ground Piping-Supplying, Installing, Testing & Commissioning of MS 'B' class medium pipe as per is medium grade of following dia, with necessary fittings such as nuts & bolts, bends, flanges ,etc and Welded joints, The pipe shall be painted with two coats red colour enamel paint over primary coat of Primer. 80 mm dia

OD83619/2025-2026 Above Ground Piping- Supplying, Installing, Testing & Commissioning of MS 'B' class medium pipe as per is medium grade of following dia, with necessary fittings such as nuts & bolts, bends, flanges ,etc and Welded joints, The pipe shall be painted with two coats red colour enamel paint over primary coat of Primer. 100 mm dia.

OD83620/2025-2026 Supplying, Installing, Testing & Commissioning of butterfly valve wafer type Stainless steel/SG iron disc , lever operated as per IS:13095 in PN 1.0 , teflon or nylon bushing, nitrile O rings in standard mounting flanges with hand lever type. BUTTERFLY VALVE - 80 mm

OD83621/2025-2026 Providing and installing in position the following type of sign boards made out of 3mm thick rigid PVC board with computer cut with texts written to recommended height in photolumiscent material complete vide technical specifications with mirror fasteners. Sizes and mounting height of the board shall be as per technical specification. Fire Duct sign board 12inch x 4inch.

UPS, Generator &amp; Solar

OD84368/2025-2026 Supply, installation, testing, commissioning of 10 kVA Online UPS(Delta/Vguard/ equivalent) Three phase input and three phase output( 320 - 460V), true online double conversion IGBT based DSP/equivalent technology controlled online UPS with isolation transformer, Input - PF - >0.99(at full load), frequency 40-70Hz, THD - <5%, input connection-input terminal x 1, Output power factorunity, voltage-380/400/415 Vac(3 phase), frequency-50/60Hz, voltage harmonic distortion-<2%, overload capacity-</=105%- continuous, Efficiency - not below 95%, Display- Graphical and Multi-lingual LCD, charging current-upto 8A and with 20 nos of 12V/100 AH exide/equivalent battery with battery rack(I-cool racks), Key features- Active harmonics filter, SVG(Static var generator), STS(Static transfer switch) and all accessories. etc complete the work as required

OD84369/2025-2026 Supply, Installation, Testing and Commissioning of 82.5 kVA Three Phase Diesel Genset of approved brand (Ashok Leyland(CPCB IV+ H4G4DE82) /Mahindra(mPower41015G)/Cummins(C82.5D5P)/Equivalent), Cooling systemwater cooled type, Engine- four stroke Turbo charged diesel engine, battery capacity- 90 Ah, engine rated -78/104(KW/HP), electric start D.G Set with acoustic enclosure and standard control panel with 125A 4P MCCB with stand by low earth fault relay using Neutral CT, additional battery charger, Voltage regulator, ammeter, voltmeter... indication lamp etc, Frequency- 50Hz, Insulation class- Class H or F, Protection- IP 23/IP 44 The engine shall be capable of taking 10% overload for one hour after 12 hours of continuous operation, Alternator brushless synchronous type, self regulated, SPDP enclosure, class F/H insulation, suitable for continuous operation at 1500 rpm, Voltage- 415 V +/- 5% at 0.8 p.f, 0.80 load factor, fuel tank capacity- not less than 145Ltr, weight- 1417 KG, Noise level-75db, range of Fuel Consumption-12-18Lr/hr (at 100% full load), rated output range-77.2-105 kW, speed-1500mm/m, wire system generally conforming to BS: 2613 & IS: 4722. The neutral of the DG set shall be provided with low set earth fault relay using adequate Neutral CT in the neutral earthing conductor. Both Engine and Alternator shall be mounted on common channel iron base frame, and with standard accessories such as anti-vibration pad, lead acid batteries (as specified by engine manufacturer) and engine driven battery charger along with leads, battery stand, fuel etc, Size -2850Lx1300Wx1510H (mm)/compatible etc complete.excl the cost of foundation (asspecified by engine manufacturer) and engine driven battery charger along with leads, battery stand, fuel etc, Size 2850Lx1300Wx1510H (mm)/compatible etc complete.excl the cost of foundation

90.12.1.30 Supply & laying of one number PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in ground including excavation of trench of size 35 x 75 cm, refilling the trench etc. as required but excluding sand cushioning and protective covering (in ordinary soil).3.5 core 70 sq mm

90.16.1.3 Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required3.15 mm copper conductor ( 10 SWG)

9.1.23 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 70 sq. mm (38mm)

5.2 Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc.(but without charcoal/ coke and salt) as required

5.8 Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

90.6.5.4 Supply and drawing the following sizes of multi-core PVC insulated & FRLS PVC sheathed 650/1100 V grade copper conductor round flexible cables conforming to IS 694 part I 1960 in the existing surface / recess conduit as required including giving necessary connections of the following sizes.2 core 1.50 sq mm

90.6.5.18 Supply and drawing the following sizes of multi-core PVC insulated & FRLS PVC sheathed 650/1100 V grade copper conductor round flexible cables conforming to IS 694 part I 1960 in the existing surface / recess conduit as required including giving necessary connections of the following sizes.4 core 1.50 sq mm

OD84421/2025-2026 Preparation of all drawings submitting and getting approval from Electrical Inspectorate if required, submitting of Completion certificates and arranging inspection, getting sanction etc. for commissioning of the DG set. All statutory payments remitted for obtaining sanction will be reimbursed on production of the original receipts.

OD84425/2025-2026 Supply, Installation and Commissioning of 4000 Lumens full HD Ultra Short Throw Laser Portable Conference room Projector of approved brand Benq/equivalent, type :3D, Chipset:DLP, maximum Projection distance: 121 Ft, lamp life -2000 hr, resolution: VGA(640X480) to WUXGA_RB(1920X1200), aspect ratio: 16:9, Maximum brightness: 4000 lms, Light source: Laser, Standby noise level: 50 dB, focus: manual focus, min operating temp- 40 degree C, internal storage not less than 2060MB. etc complete

OD84448/2025-2026 Supply of PA Microphone stand of approved brand- Ahuja/equivalent, type - floor stand, height adjustment range-920-1500mm, base dia- min 230mm, weight not less than 4.6 Kgs.

OD84449/2025-2026 Supply of PA Wireless Microphone of approved brand- Ahuja/equivalent, type- set of 1 no. of one handheld wireless microphone, mic type- dynamic, frequency-50 15,000 Hz, power supply: receiver:230V AC, Microphone:2x1.5 V Battery cells

OD84450/2025-2026 Supply of PA Wired Microphone of approve brand- Ahuja/equivalent, Mic typedynamic, frequency response-50-15,000 Hz, sensitivity-2.5mV/Pa, impedance 600 OHMS, including cable for 6 m.

OD84451/2025-2026 Supply and Fixing PA Mixer of approved brand- Ahuja/equivalent, input-4Mic,/2 sterio, in built USB/bluetooth player, power supply-AC 230 V, dimensions W281xH75xD210 mm, weight not less than 1.6Kgs.

OD84452/2025-2026 Supply of PA Speaker stand of approved brand-Ahuja/equivalent, Height adjustment: 105cm -175cm, load capacity-40Kgs, Weight not less than 4.7Kgs.

OD84453/2025-2026 Supply and Installation of PA Speaker system of approved brand Ahuja/equivalent, power output-100W (RMS), connectivity-wired, configuration-2 way, SPL at (1W/1m0-97dB, max. Rated SPL-117dB, frequency response-55 20000Hz, dimension-W410xH530xD380mm, weight not less than 15.40Kgs.

OD84454/2025-2026 Supply and Installation of PA Mixer amplifier of approved brand and manufacturer(Philips/Ahuja/Medha D.J/ equivalent), Output-160W (RMS), power consumption-300 VA, voltage-120Volts, noise level-60dB, dimension W420xH155xD320mm, power source-AC, connectivity-USB, power sourcebattery powered, frequency-65Hz, operation control- remote/manual, weight not less than 13.60Kgs

OD84456/2025-2026 Supply and providing All-in-one design Podium with power supply- 230V/50Hz/ 110V/60Hz, Power consumption- 100W, Freqency response- 100Hz-16000Hz, input- MIC1: -50dB±2dB/6000, MIC2: -55dB±2dB/6000 Wireless, MIC-20dB 2dB/50 AUX -20dB 2dB/10, Output-1V/0dB, Tone Controls- Bass: ± 10dB, Treble :±10dB, Range- 15-50m, Dimensions-580(L) x 420(W) x 1100(H)mm/Equivalent, Weight - not less than 29Kg. components -In built 60W amplifier, 60W column speaker with one tweeter and three woofers, A flexible gooseneck microphone and lamp, wooden top and steel bottom, steel body: goose neck MIC length: 47cm, lamp length 45cm.

OD84457/2025-2026 Supply, Installation, Testing and Commissioning of 40kWp On Grid Solar Power Plant with 19 Nos of 540 WP mono perc half cut (non-DCR) Solar panel module of approved make (Adani/ Waree Solar/Tata power/ equivalent), PCU/invertor-40KW three phase with wifi (for online monitoring) BIS certified approved brand (Polycab/Deye/Havells/equivalent), ACDB(AC Distribution box)-& DCDC(DC Distribution box)- IEC standard IP65 box with MCB SPD and fuse unit, DC cable 10 sqmm UV rated 1500 V solar cables, 4 set of earthing and lightening protection- Excel earthings with ISI certified, copper bonded earth rod, 10swg copper, multispoke lightening arrester, 50 sq mm AI ground conductor chemical earth compound including system components having ISI standing meter box, isolator, connectors, pipe and accessories, Mounting structure- lattice type module mounting structure with epoxy coated GI frame(Excluding the cost of armoured cables to control panel, KSEB fee for feasibility report & registration, KSEB NET METER).

OD84458/2025-2026 Supply and fixing Quick destroy incinerator with burning capacity- Up to 25 pads per cycle, mode of operation- Fully Automatic/Temperature and Timer Cutoff, Dimension(mm) - 250L x 250B x 620H, Heater Watts- 1250/2000 watts, Burning Time 12 mins, Exhaust Pipe 2" Flexible hose

Furniture

OD84714/2025-2026 Supply and providing Executive High back revolving chair- Head rest height and angle adjustable. Seat Height adjustment Back rest angle Adjustable. Armrests 3d multi-function. Back upholstered with nylon mesh. Seat upholstered with nylon mesh. Multi -function 3 class locking mechanism. Powder coated/Electro plated TUV-CLASS 4 Gas spring 120mm, Aluminum base with PU castors:330mm Tested as per BIFMA X5.1 standards including cost and conveyance of all materials and labor charges for making.

OD84718/2025-2026 Supplying and Providing storage cupboard Using Marine plywood 16mm conforming to ISO 9001-2015/BS 1088-2003/ASTM D7295-14 standards and 1 mm Mica finish, 2mm PVC Edge band all complete as per the direction of engineer in charge and as per the drawing produced.

OD84726/2025-2026 Supplying and providing Sofa Set ( 3 + 2 ) seater as per the approved design; where as 3 seater of size 180 x 90 x 50 cm and 2 seater of size 120 x 90 x 50 cm Seat & backrest upholstered with leatherette 14 Gauge pipe 1.25 thickness Powder coated/ electro plated chrome mild steel cantilever base. Tested as per BIFMA X5.1 standards including cost and conveyance of all materials and labor charges for making etc. complete.

OD84727/2025-2026 Supply and providing Teapoy Using Marine plywood 16mm with ISO/ISI-9001-2015 and 1 mm Mica finish, 2mm PVC Edge band, size of - 90Lx45Wx60H cm including cost and conveyance of all materials and labor charges for making.

OD84728/2025-2026 Design, Supply, Fabrication and Installation of 12 mm thick HPL(High-Pressure- Laminate) sheet of approved brand and manufacturer for fabrication of cubicle type partitioning with composite laminated HPL sheet, sheet shall conforming to ISO 4586/ASTM E162/BS EN 438 standards, sheet shall be fixed with SS Gravity hinges, SS Adjustable leg, SS coat hook, SS door knob, aluminum U channel, SS lockset with indicator, aluminum anodized top rail, aluminum door stopper channel, SS 304 graded screws, wall plugs, noise deafening tapes for grooves in doors & pilasters etc. complete. The rate includes all cost of materials, labour charges for fabrication of the cubicle and the measurements will be taken the area of the complete sheets used.

OD84731/2025-2026 Supply and Fixing Premium Quality Zebra Roller Blinds, Material- Polyester Blend/Polyster material @ 280GSM, Opacity- Light Filtering Inches/sheer, Pattern - Solid/equivalent, mounting type-Inside wall mount, operation mode - manual, Control Type - Cord control, aluminium brackets & railings, Features- High Quality/ durable/UV protection/stain resistant/Light Filtering, Application for Office room, drawing room, etc complete.

OD84732/2025-2026 Supply and Fixing Premium Quality 100% Blackout Roller Blinds, Material- Polyester coated material-100% blackout fabric, Opacity- Blackout Inches, Pattern - Solid/equivalent, mounting type- Inside wall mount, operation mode - manual, Control Type - Cord control, aluminium brackets & railings, Features- High Quality/ durable/UV protection/water proof, Application for Office room, drawing room, etc complete.

OD84733/2025-2026 Supplying and Providing Executive Table using 16mm Marine Plywood conforming to ISO-9001-2015/ISO 14001-2015/BS 1088-2003 and 1 mm Mica finish, 2mm PVC Edge band, in the right hand side using hinged doors ; top with a sliding drawer, keyboard drawer; Stainless steel soft close telescopic channel & soft close hinges of approved brand ( EBCO or equivalent) ; 100 mm size SS handles ; locking facility ( ISI),provision for CPU/UPS etc. as per approved drawing details including cost and conveyance of all materials and labor charges for making , fixing the table etc complete.- Minimum height of table to be supplied-75cm - (Measurement to be made for top surface area)

OD84734/2025-2026 Providing and Fixing Cup board/Shelves with 17mm thick WPC(wood polymer composite) panel board conforming to ISO 9001-2015/ISO 14001-2015/ASTM D7295-14 standards and covered with 1mm mica at both sides & having 2mm edge band, fixing with screws and fittings etc, materialfoamed/ solid/textured/embossed WPC panel board, finish- laminate/UV coated/veneer, density-0.8-1.2 g/cm3, tensile strength -10-20MPa, water absorption - <5%, impact resistance-10-20 kJ/m2, flexural strength-20-30 MPa. etc complete.

OD84735/2025-2026 Wall paneling with 10mm thick WPC(wood polymer composite) panel board and framing with 16mm thick marine ply board covered with 1mm mica at both sides & having 2mm edge band, WPC panel board should conforming to ISO 9001-2015/ISO 14001-2015/ASTM D7295-14 standards, materialfoamed/ solid/textured/embossed WPC panel board, finish- laminate/UV coated/veneer, density-0.8-1.2 g/cm3, tensile strength -10-20MPa, water absorption - <5%, impact resistance-10-20 kJ/m2, flexural strength-20-30 MPa. etc complete.

OD84736/2025-2026 Supply and Fixing Wall/ceiling mount projector screen of approved brand(Inlight/Big Vue/equivalent) 120 inches Diagonal, UHD-3D-4K Ready Technology Motorized Projector Screen 4:3 Picture Aspect Ratio, 8 Ft. x 6 Ft., with Cordless Remote(White), Product Dimensions-2.72W x 2H Meters, Material- Fabric, Display Dimensions96x72 Inches. modes-Ultra hd, 3d and 4k/ compatible.etc complete.

OD84737/2025-2026 Supply and Installation of LCD Projector :- Projection System- FULL HD DLP single of approved brand(BenQ/Sony/Portronics/equivalent), DMD Type/equivalent - 0.55" X GA, Native resolution - 1920x1080 pixel/ compatible, Brightness - 4000 ANSI Lumens/ nearest, Contrast ratio- 20,000:1, Display color - 30 bits /1.07 billion colors, Aspect ratio- Native 16:9, Light source- Lamp, Light source life - normal - 15,000 hr, Throw ratio - 1.49-1.64, Zoom ratio - 1.1 x ,Keystone correction- Auto ID, Vertical +/- 40 degree, Projection Offset - 110,0%, Feature - 1D Auto Keystone, High Brightness, Spreadsheet mode, Bright Mode, Presentation Mode, Infographic Mode, Video Mode, Srgb Mode, Accessories (Standard) - Quick Start Guide(4J.JND01.001) Remote Control (5J.JND06.001)AAA Battery x 2 VGA Cable (1.5m) Power Cord (1.8m), video compatibility- SECAM/NTSC/PAL/equivalent, uses- meeeting room etc, weight-2.3 kgs, inputs- USB mini-B, HDMI*2, RS-232, Wireless connectivity- Optional dongle support/compatible.

OD84741/2025-2026 Supply and providing Executive High back revolving chair- Head rest height and angle adjustable. Seat Height adjustment Back rest angle Adjustable. Armrests 3d multi-function. Back upholstered with nylon mesh. Seat upholstered with nylon mesh. Multi -function 3 class locking mechanism. Powder coated/Electro plated TUV-CLASS 4 Gas spring 120mm, Aluminum base with PU castors:330mm Tested as per BIFMA X5.1 standards including cost and conveyance of all materials and labor charges for making.

OD84743/2025-2026 Supplying and Providing Executive Table using 16mm Marine Plywood conforming to ISO-9001-2015/ISO 14001-2015/BS 1088-2003 and 1 mm Mica finish, 2mm PVC Edge band, in the right hand side using hinged doors ; top with a sliding drawer, keyboard drawer; Stainless steel soft close telescopic channel & soft close hinges of approved brand ( EBCO or equivalent) ; 100 mm size SS handles ; locking facility ( ISI),provision for CPU/UPS etc. as per approved drawing details including cost and conveyance of all materials and labor charges for making , fixing the table etc complete.- Minimum height of table to be supplied-75cm - (Measurement to be made for top surface area)

OD84745/2025-2026 Supply and providing Visitors chair, cushioned seat and back, Backrest, mild steel frame powder coated and upholstered with nylon mesh Armrest fixed- PP with fiber. Seat upholstered with imported fabric. 2.1mm thick, fixed round tube Powder coated/ electro plated chrome mild steel cantilever base. Tested as per BIFMA X5.1 standards including cost and conveyance of all materials and labor charges for making.

OD84746/2025-2026 Supply and providing Two seater Sofa cushioned - Seat & backrest upholstered with leatherette 14 Gauge pipe 1.25 thickness Powder coated/ electro plated chrome mild steel cantilever base. Tested as per BIFMA X5.1 standards including cost and conveyance of all materials and labor charges for making.

OD84761/2025-2026 Supply and providing Library reading Table using 18g steel powder coated (7tank) With using 8mm glass partition of 50cm Height, for three persons, with SS brackets 2 nos for single partition including cost and conveyance of all materials and labor charges for making

OD84762/2025-2026 Supply and Providing Library Chair - Backrest, mild steel frame powder coated and upholstered with nylon mesh Armrest fixed- PP with fiber. Seat upholstered with imported fabric. 2.1mm thick, fixed round tube Powder coated/ electro plated chrome mild steel cantilever base. Tested as per BIFMA X5.1 standards including cost and conveyance of all materials and labor charges for making.

OD84763/2025-2026 Supply and Providing Library rack:- by using good quality 18mm,15mm,12mm,Marine grade Plywood conforming to ISO 9001:2015/BIFMA standards with two side mica finish, edge with 2mm PVC edge Beeding, with all fitting accessories of size- 240x40x210 H cm. etc complete

OD84765/2025-2026 :Supplying pad folding chair with-auditorium type good quality of equivalent and conforming to ISO-9001:2015, upholstery material-100% polyester/compatible, frame- marine ply/engineered wood/powder coated frame GI (50 microns), seat material- foam, approved color including the cost of materials, freight, loading & unloading chair Complete

Item Rate BoQ

BoQ_Ver4.0

Name of the Bidder/ Bidding Firm / Company :

(This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only)

NUMBER #

ESTABLISHING MODERN TRAINING INFRASTRUCTURE AT SFTI WALAYAR - TRAINEES ACCOMODATION

Civil Works

2.31 Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared

2.6.1 Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan)including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5m, as directed by Engineer-in-charge.All kinds of soil

2.7.3 Earth work in excavation by mechanical means (Hydraulic excavator )/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan)including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.Hard rock (blasting prohibited)

2.9.3 Excavation work by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan),including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50 m.Hard rock (blasting prohibited)

2.13.3.2 Excavating trenches of required width for pipes, cables, etc, including excavation for sockets, depth up to 1.5 m including getting out the excavated materials, returning the soil as required in layers not exceeding 20 cm in depth. including consolidating each deposited layers by ramming, watering etc., stacking serviceable material for measurements and disposal of unserviceable material as directed, within a lead of 50m: Hard rock (blasting prohibited)Pipes, cables etc. exceeding 80 mm dia but notexceeding 300 mm dia.

2.13.3.3 Excavating trenches of required width for pipes, cables, etc, including excavation for sockets, depth up to 1.5 m including getting out the excavated materials, returning the soil as required in layers not exceeding 20 cm in depth. including consolidating each deposited layers by ramming, watering etc., stacking serviceable material for measurements and disposal of unserviceable material as directed, within a lead of 50m:Hard rock (blasting prohibited)Pipes, cables etc. exceeding 300 mm dia but not exceeding 600 mm dia

50.2.26.1 Filling with contractor own earth (excluding rock) in open areas in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m as per direction of site Engineer-incharge.

2.25 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

51.2.3 Filling with Quarry Muck Filling up low lying and water logged areas with local material/quarry muck, spreading in layers, leveling the top at site and consolidation by ramming, etc complete for improving the CBR value of subgrade

60.5.1 DOWEL BARS - Supplying and providing MS dowel bars of size 20 mm dia, 1.5m long (1m in rock and 0.5 m in concrete) including drilling holes of 25mm dia and filling the gap with cement grout (0.25kg/each) etc complete

OD96801/2025-2026 Application of Epoxy/Fosroc Lokfix P/equivalent non-expansive chemical grout over reinforcement bars/bolts for high strength, corrosion resistant anchoring in concrete, rock and masonry strata etc. (measurement shall be made for length of bar coated) for 12 to 25 mm dia bars.

60.7.1 DRY RUBBLE MASONRY _ Dry rubble without concrete levelling course masonry with good quality blasted rubble including packing to compactness to lines and levels cost and conveyance of all materials labour charges etc. complete as per direction of Departmental officers at site

7.1.1 Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement: 6 coarse sand: 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement: 6 coarse sand)

4.1.8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement: 4 coarse sand (zone-III) derived from natural sources: 8 graded stone aggregate 40 mm nominal size derived from natural sources)

4.1.5 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:3:6 (1 Cement: 3 coarse sand (zone-III) derived from natural sources: 6 graded stone aggregate 20 mm nominal size derived from natural sources)

4.1.3 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement: 2 coarse sand (zone-III)derived from natural sources: 4 graded stone aggregate 20 mm nominal size derived from natural sources)

5.1.2 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size derived from natural sources)

5.3 Reinforced cement concrete work in beams, suspended floors, roofs, having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills,staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with1:1.5:3 (1 cement : 1.5 coarse sand (ZoneIII) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources).

5.22.6 Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth level Thermo - Mechanically Treated bars of grade Fe-500D or more

5.9.1 Centering and shuttering including strutting, etc. and removal of form for: Foundations, footings, bases of columns, etc for mass concrete

5.2.2 Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up tot floor five level excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3(1 cement: 1.5 coarse sand: 3 graded stone aggregate 20 mm nominal size derived from natural sources)

5.9.7 Centering and shuttering including strutting, etc. and removal of form for: Stairs, (excluding landings) except spiral - staircases)

5.22A.6 Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo - Mechanically Treated bars of grade Fe-500D or more

5.9.6 Centering and shuttering including strutting, etc. and removal of form for: Columns, Pillars, Piers, Abutments, Posts and Struts

26.30.1 Drilling suitable holes in reinforced or plain cement concrete with power driven drill machine to a minimum depth of 100mm upto 200mm in RCC beams, lintels, columns and slabs to introduce steel bars for sunshades/balconies including fixing the steel bars in position using epoxy resin anchor grout of approved make but excluding the cost of reinforcement, all complete as per direction of Engineer-In-Charge. Upto and including 12mm dia.

5.9.5 Centering and shuttering including strutting, etc. and removal of form for: Lintels, beams, plinth beams, girders bressumers and cantilevers

5.9.3 Centering and shuttering including strutting, etc. and removal of form for: Suspended floors, roofs, landings, balconies and access platform

4.11 Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement: 2 coarse sand (zone-III) derived from natural sources: 4 graded stone aggregate 20mm nominal size derived from natural sources).

4.17 Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand (zone-III) derived from natural sources: 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

50.6.2.1 Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x15 cm or nearest available size confirming to IS 2185 part I of 1979 for foundation and plinth with thickness 15cm in: CM 1:6 (1 cement : 6 coarse sand) etc complete

50.6.1.5 Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 Part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 (1 cement: 6 coarse sand) etc complete .

50.6.1.9 Solid block masonry using pre cast solid blocks(Factory made) of size 40x20x15 cm or nearest available size confirming to IS 2185 part I of 1979 for super structure above floor two level upto floor five level with thickness 15cm in: CM 1:6 (1 cement : 6 coarse sand) etc complete .

50.6.2.2 Solid masonry using pre cast solid blocks (factory made) of size 30x20x15cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level with thickness 15cm in: CM 1:6 (1 cement: 6 coarse sand) etc complete.

50.6.3.2 Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x10 cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level for 10 cm thick wall in : CM 1:6 ( 1 cement : 6 coarse sand) including cost of scaffolding complete

6.47 Providing and laying Autoclaved Aerated concrete (AAC) blocks masonry 150mm/230mm/300 mm thick with Grade- I AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).

6.15 Extra for providing and placing in position 2 Nos 6 mm dia M.S bars at every third course of half brick masonry.

10.14.2.1 Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm pressed, mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in- charge: Profile CFixing with adjustable lugs with split end tail to each jamb

10.17 Providing and fixing M.S. fan clamp type I or II of 16 mm dia M.S. bar, bent to shape with hooked ends in R.C.C. slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete.

9.165.1 Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete. 125 mm

9.76 Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

9.53 Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

9.153 Providing and fixing steel (white power coated) crescent lock for uPVC sliding window/ door with necessary screws etc. complete.

9.147A.3 Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 +/- 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Casement window double panels with top fixed with S.S. friction hinges (350 x 19 x 1.9 mm) made of (small series) frame 47 x 50 mm, sash 47 x 68 mm & mullion 47 x 68 mm all having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area of window upto 2.50 sqm).

9.147A.6 Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 +/- 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance

9.85 Providing and fixing bright finished brass. casement window fastener with necessary screws etc. complete.

9.86.1 Providing and fixing bright finished brass casement stays (straight peg type) with necessary screws etc. complete: 300 mm weighing not less than 330 gms.

9.86.2 Providing and fixing bright finished brass casement stays (straight peg type) with necessary screws etc. complete:250 mm weighing not less than 280 gms.

9.86.3 Providing and fixing bright finished brass casement stays (straight peg type) with necessary screws etc. complete:200 mm weighing not less than 240 gms.

9.149 Providing and fixing casement handle made of zinc alloyed (white powder coated) for uPVC casement window with necessary screws etc. complete.

9.150 Providing and fixing zinc alloyed (white powder coated) touch lock for uPVC sliding window with necessary screws etc. complete.

9.151 Providing and fixing steel roller for uPVC sliding window with necessary screws etc. complete.

9.152 Providing and fixing steel roller for uPVC sliding door with necessary screws etc. Complete.

9.116 Providing and fixing sliding arrangement in racks/ cupboards/cabinets shutter by with stainless steel rollers to run inside C or E aluminium channel section (The payment of C or E channel shall be made separately

9.147B.1 Providing and fixing factory made uPVC white colour fixed glazed windows/Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.)

21.3.2 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5.50 mm thickness (weight not less than 12.50 kg/sqm)

9.71.1 Providing and fixing IS: 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc. complete: 125x64x2.50 mm

9.71.3 Providing and fixing IS: 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc. complete: 75x50x2.50 mm

9.70.2 Providing and fixing IS: 12817 marked stainless steel butt hinges with stainless steel screws etc. complete: 100x58x1.90 mm.

9.103 Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS: 1868) aluminium lever handles of approved quality with necessary screws etc. complete.

9.84 Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS: 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width form 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

21.4.1 Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS: 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors including cost of cutting floors, embeding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer -in- Charge. With stainless steel cover plate minimum 1.25 mm thickness .

9.143 Providing and fixing factory made uPVC door frame, made of uPVC extruded section, of size $65~mm\times55$ mm with wall thickness 2.0 mm (? 0.2mm), corners of the door frame to be mitred cut and jointed with plastic brackets and stainless steel screws, reinforcing hinge side vertical of the frames with PVC profile of Size 28 mm x 30 mm having wall thickness 2 mm (? 0.2 mm), including providing & fixing 3 nos of 125 mm long stainless steel hinges to the frame, fixing the frame with jamb with required number & size of anchor dash fastners, all complete as per manufacturer's specification and direction of Engineer-in-charge.

9.147C.1 Providing and fixing factory made uPVC white colour casement/ Casement cum fixed glazed door comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 +/- 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge.(Single / double glass panes and silicon sealent shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Casement door with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 +/- 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.00 sqm).

9.148.1 Providing and fixing stainless steel (SS-304 grade) friction hinges to the side/ top hung uPVC windows, of approved quality, with necessary stainless steel screws etc. as per direction of Engineer - in-charge.200 x 19 x 1.9 mm.

9.148.2 Providing and fixing stainless steel (SS-304 grade) friction hinges to the side/ top hung uPVC windows, of approved quality, with necessary stainless steel screws etc.as per direction of Engineer - in-charge.250 x 19 x 1.9 mm.

9.148.4 Providing and fixing stainless steel (SS-304 grade) friction hinges to the side/ top hung uPVC windows, of approved quality, with necessary stainless steel screws etc.as per direction of Engineer - in-charge.350 x 19 x 1.9 mm.

10.29.2 Providing & fixing fly proof wire gauze to windows... Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both sides.

10.28 Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge,(for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)

10.16.1 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes.

13.52.1 Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriatepriming coat, preparation of surface, etc. complete.On steel work

12.1.1 Providing corrugate G.S. sheet roofing including vertical/ curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete ( up to any pitch in horizontal / vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.1.00 mm thick with zinc coating not less than 275 gm/m2

OD96810/2025-2026 Providing and fixing 200mm wide, 140mm deep 3 mm thick plain UPVC moulded channel type Rainwater gutter pipe of approved brand and manufacturer(aquastar/euroguard/equivalent) with added ribs for extra strength, capacity-20L/m, iron brackets- 900x30x3 mm size @ 0.6/0.7m spacing, bolts, nuts and washers etc., including making necessary connections with rain water down fall pipes etc. complete .

50.18.9.18.1 Providing and fixing PVC pipes including fixing the pipe with clamps/clips at 1.00 m spacing. This included jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 75 mm dia 6Kgf/cm2 - External work- Exposed on wall

50.18.9.21.9 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes,including jointing with PVC solvent cement - 75 mm dia Socket /coupling

50.18.9.22.12 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110x75 mm dia Reducer

8.2.2.2 Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Area of slab over 0.50 sqm

8.3.2 Providing edge moulding to 18 mm thick marble stone counters, vanities etc.,including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer -in-Charge.Granite work

8.6 Mirror polishing on marble work/ granite work/stone work where ever required togive high gloss finish complete.

8.5 Extra for providing opening or required size & shape for wash basin/kitchen sink in kitchen platform, vanity counter and similar location in marble/granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

50.18.78 Making chases up to 12.5x12.5 cm in walls including making good and finishing with matching surface after housing pipe etc.

Finishing Work

12.45.3 Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm,at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section andperimeter channel with the help of dry wall screws of size 3.5x25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with:12.5 mm thick tapered edge gypsum moisture resistant board

12.42.5.2 Providing and fixing on wall face unplasticised- PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A,including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap forthermal expansion Bend 87.5⁰110 mm bend

13.1.1 12 mm cement plaster of mix: 1:4 (1 cement: 4 fine sand)

26.78.1 Providing & Applying weather proof sealant on outer joints of approved make confirming to IS & directed by Engineer-in-charge. Sealant 25mmx10mm at joints

13.2.2 15 mm cement plaster on the rough side of single or half brick wall of mix: 1:6 (1 cement: 6 fine sand)

13.16.1 6mm cement plaster of mix:1:3 (1 cement: 3 fine sand)

13.7.1 12 mm cement plaster finished with a floating coat of neat cement of mix: 1:3 (1 cement: 3 fine sand)

13.18 Neat cement punning

13.76 Forming groove of uniform size from 12x12 mm and upto 25 x 15 mm in the top layer of washed stone grit plastered surface as per approved pattern, including providing and fixing aluminum channels of appropriate size and thickness (not less than 2 mm), nailed to the under layer with rust proof screws and nails and finishing the groove complete as per specifications and direction of the Engineer-in-Charge.

13.29.3 18 mm thick plain cement mortar band in cement mortar 1:4 (1 cement: 4 fine sand): Raised Band

5.30 Add for plaster drip course / groove in plastered surface or moulding to R.C.C. projections.

13.80 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

2.34.1 Supplying chemical emulsion in sealed containers including delivery as specified. Chlorpyriphos / Lindane emulsifiable concentrate of 20%

2.35.3.1 Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion): Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floor: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

13.22 Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof.

13.43.1 Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface: Water thinnable cement primer

13.60.1 Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade: Two or more coats on new work

13.45.1 Finishing walls with textured exterior pint of required shade: New work (Two or more coats applied @3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm

13.52.1 Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete. On steel work

13.61.1 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade: Two or more coats on new work

22.2.1 Providing and laying integral cement based treatment for water proofing on the vertical surface by fixing specified stone slab 22 mm to 25 mm thick with cement slurry mixed with water proofing compound conforming to IS: 2645 in recommended proportion with a gap of 20mm (minimum) between stone slabs and the receiving surfaces and filling the gaps with neat cement slurry mixed with water proofing compound and finishing the exterior of stone slab with cement mortar 1:3 (1 cement: 3 coarse sand) 20 mm thick with neat cement punning mixed with water proofing compound in recommended proportion complete at all levels and as directed by Engineer-in-Charge: Using rough Kota stone

22.5 Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying: a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

16.9 Scarifying metalled (water - bound) road surface including disposal of rubbish, lead upto 50 m and consolidation of the aggregate received from scarifying with power road roller of 8 to 10 tonne capacity.

21.18 Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc to be paid separately)

50.4.1.1 Providing and laying in position cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 12.5 mm nominal size) up to floor five level excluding the cost of centering, shuttering, finishing for leveling coarse of floor and roof etc.

9.48.2 Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings/ wooden frames with rawl plugs screws etc

8.31 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

11.41.2 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm.

11.41.3 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 800x 800 mm

11.48.2 Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg). including filling/grouting and finishing complete as per direction of Engineer-in-charge. Size of Tile 600x600 mm

11.48.3 Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg). including filling/grouting and finishing complete as per direction of Engineer-in-charge. Size of Tile 800x800mm

11.49.2 Providing and laying Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately). Size of Tiles 600x600 mm

OD97184/2025-2026 Providing and fixing in position factory made PIR insulated sandwich wall/roof light weight solid core panels. The outer face on both sides of the panels will be pre-coated galvanized steel with 0.35 or 0.45 mm thick each. Panel shall be preferably fixed into 'C' channel made of 50mm size Stainless Steel screwed/fastened to the slab/column/beam etc. The panel shall fix vertically with tongue and groove joint and horizontally locked with steel bar between each. Panels should be used as floor & roofing with additional structural support, steel or RCC depending upon the design. All the operation shall be completed in all respect as per drawings, Manufacturers specifications and under the overall direction of Engineer-in-Charge (Cost of all the material is included except "C channel" which will be paid separately). Non load bearing panels 30mm thick of required size

OD97185/2025-2026 Wall paneling with 10mm thick WPC(wood polymer composite) panel board and framing with 16mm thick marine ply board covered with 1mm mica at both sides & having 2mm edge band, WPC panel board should conforming to ISO 9001-2015/ISO 14001-2015/ASTM D7295-14 standards, material foamed/solid/textured/embossed WPC panel board, finish- laminate/UV coated/veneer, density-0.8-1.2 g/cm3, tensile strength-10-20MPa, water absorption - <5%, impact resistance- 10-20 kJ/m2, flexural strength-20-30 MPa. etc complete.

50.9.12.1 Providing and fixing Thomson Multi wood board or equivalent make, in shelves with screws and fittings wherever required, edges to be painted with polyurethane primer (fittings to be paid separately) as per the direction of site Engineer-in-charge.

OD97190/2025-2026 Providing and Fixing Cup board/Shelves with 17mm thick WPC(wood polymer composite) panel board conforming to ISO 9001-2015/ISO 14001-2015/ASTM D7295-14 standards and covered with 1mm mica at both sides & having 2mm edge band, fixing with screws and fittings etc, material foamed/ solid/textured/embossed WPC panel board, finish- laminate/UV coated/veneer, density-0.8-1.2 g/cm3, tensile strength -10-20MPa, water absorption - <5%, impact resistance-10-20 kJ/m2, flexural strength-20-30 MPa. etc complete.

OD97194/2025-2026 Providing and fixing ISI marked flush/panelled door shutters with hardwood conforming to ISO 8271/ ISO 8272/ISO 9001/ISO 14001 & of decorative Type, hardwood with frame of 1st class hardwood board and well matched commercial 1mm thick decorative mica lamination on both faces of shutters and 2mm thick edge band, finish- teak/laminated/compatible: 30-35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws (Cost of glazing shall paid extra and portion of glazing shall deduction from measured area)

9.90.1 Providing and fixing special quality chromium plated brass cupboard locks with six levers of approved quality including necessary screws etc. complete. Size 40 mm

9.90.4 Providing and fixing special quality chromium plated brass cupboard locks with six levers of approved quality including necessary screws etc. complete. Size 75 mm

9.114.1 Providing and fixing magnetic catcher of approved quality in cupboard/ward robe shutters, including fixing with necessary screws etc. complete. Triple strip vertical type

9.114.2 Providing and fixing magnetic catcher of approved quality in cupboard/ward robe shutters, including fixing with necessary screws etc. complete. Double strip (horizontal type)

9.165.1 Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete. 125 mm

9.165.2 Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete. 100mm

9.165.3 Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete. 75 mm

9.70.1 Providing and fixing IS: 12817 marked stainless steel butt hinges with stainless steel screws etc. complete: 125x64x1.90 mm

9.70.2 Providing and fixing IS: 12817 marked stainless steel butt hinges with stainless steel screws etc. complete: 100x58x1.90 mm

9.70.4 Providing and fixing IS: 12817 marked stainless steel butt hinges with stainless steel screws etc. complete: 50x37x1.50 mm

9.71.1 Providing and fixing IS: 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc. complete: 125x64x2.50 mm

9.76 Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

9.80 Providing and fixing 50 mm bright finished brass cup board or wardrobe knob of approved quality with necessary screws.

Upper Roof Structure

50.10.1 Steel work in built up G I tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

10.2 Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

8.8.1.2 Providing and fixing expansion hold fasteners on C.C./R.C.C./Brick masonry surface backing including drilling necessary holes and the cost of bolt etc complete. Wedge expansion type Fastener with threaded dia 10 mm.

10.16.1 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes.

12.50 Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

6 OD152291/2025-2026 Providing and fixing Sandwich Polyurethane Foam (PUF) Panel roofing sheets (size,shape and pitch of corrugation as approved by Engineer-in-charge) 30 mm thick(PUF panel sandwiched between precoated galvanized iron profile sheet 0.50mm thick top sheet and 0.35mm bottom sheet), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, strength -240 MPA-550MPA, coating mass- AZ 70- AZ 150, Overall density- 40-42 kg/m35-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch horizontal/ vertical or curved surfaces,excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

12.52.1 Providing and fixing tiled false ceiling of approved materials of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 grams per sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x 1.6 mm fixed to ceiling with 12.5mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85x 30x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all Tsections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer -in-charge.GI Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending

OD152286/2025-2026 Providing and fixing 200mm wide, 140mm deep 3 mm thick plain UPVC moulded channel type Rainwater gutter pipe of approved brand and manufacturer(aquastar/euroguard/equivalent) with added ribs for extra strength, capacity-20L/m, iron brackets- 900x30x3 mm size @ 0.6/0.7m spacing, bolts, nuts and washers etc., including making necessary connections with rain water down fall pipes etc.complete

OD97233/2025-2026 Supply and Installation of Automatic Whirlybird Non Power Wind Roof Turbine Ventilator, Turbine Material- Stainless steel 304 grade, dia-600 mm, base- 6 core poly-carbonate sheet, No. of blade-36 Nos, type - wind driven, automatic grade- automatic, weight- not less than 5 kgs. etc complete

50.18.9.18.1 Providing and fixing PVC pipes including fixing the pipe with clamps/clips at 1.00 m spacing. This included jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 75 mm dia 6 Kgf/cm2 - External work- Exposed on wall.

50.18.9.19.1 Providing and fixing PVC pipes including fixing the pipe with clamps/clips/ at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 110 mm dia 6 Kgf/cm2 - External work- Exposed on wall.

50.18.9.10.1 Providing and fixing PVC pipes includings jointing of pipes with one step pvc solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 150 mm dia 6 Kgf/cm2.

50.18.9.21 Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75 mm dia Elbow.

50.18.9.21.3 Providing and fixing PVC moulded fittings / accessories for Rigid PVC pipes , including jointing with PVC solvent cement -75 mm dia Door Elbow.

50.18.9.21.4 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75 mm dia Bend.

50.18.9.21.5 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement -75x75x75 mm dia Tee.

50.18.9.22.2 Providing and fixing PVC moulded fittings / accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 mm dia 45 degree Elbow.

50.18.9.22.4 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement- 110 mm dia Bend.

50.18.9.22.8 Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement -110 mm dia Vent cowl.

50.18.9.22.9 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement -110 mm dia offset.

50.18.9.22.10 Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement -110 mm dia End Cap.

50.18.9.22.11 Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 mm dia Socket/ coupling.

50.18.9.22.12 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110x75 mm dia Reducer.

10.25.2 Item Shifted to Sub head 14 as item 14.73 Item Shifted to head 14 as item 14.74 Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

13.52.1 Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete. On steel work.

OD97257/2025-2026 Providing and fixing matt finished terracotta clay jali in cement mortar 1:6 (1 cement : 6 coarse sand)used for facades & internal partitions etc., which gives circulation of natural light and fresh air, supporting frame with MS angle/flat, pointing the joints, closing the joints with white cement, rubbing and cleaning to smooth finish etc. As per standard specification.(supporting frame shall be paid additionally)

21.5 Providing and fixing powder coated aluminium work ( minimum thickness of powder coating 50 micron) consisting of tee /angle sections, of approved make conforming to IS : 733 in frames of false ceiling including aluminium angle cleats with necessary C.P brass/ stainless steel sunk screws, aluminium perimeter angles fixed to wall with stainless steel rawl plugs @ 450 mm centre to centre and fixing the frame work to G.I level adjusting hangers 6 mm dia. with necessary cadmium plated machine screws all complete as per approved architectural drawings and direction of the Engineer-inCharge ( level adjusting hangers, ceiling cleats and expansion hold fasteners to be paid for separately ).

OD97274/2025-2026 Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 3.25mm thick aluminium composite panel material consisting of 2.25mm thick FR grade mineral core sandwiched between two Aluminium sheets (each0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.s The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete, as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places.

Plumbing

17.2.1 Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: W.C. pan with ISI marked white solid plastic seat and lid

17.7.1 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

17.10.1.1 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required: Kitchen sink with drain board510x1040 mm bowl depth 250 mm

17.10.2.1 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required: Kitchen sink without drain board610x510 mm bowl depth 200 mm

17.10.1.2 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required:Kitchen sink with drain board510x 1040 mm bowl depth 225 mm

50.17.1.4 Supplying and fixing CP Health faucet good quality including cost of materials and labour charges etc. complete as per the direction of site engineer-in-charge.

9.149 Providing and fixing casement handle made of zinc alloyed (white powder coated) for uPVC casement window with necessary screws etc. complete.

17.31 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

18.18.3 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete: 25 mm nominal bore

18.53.1 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS: 8931. 15 mm nominal bore

17.71 Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms

18.7.3 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Internal work - Exposed on wall 25 mm nominal dia pipes.

18.7.4 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Internal work - Exposed on wall 32 mm nominal dia pipes

18.7.6 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Internal work - Exposed on wall 50 mm nominal dia pipes

18.8.3 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 25 mm nominal dia pipes

18.8.4 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 32 mm nominal dia pipes

50.18.9.9.1 Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of Joints complete as per direction of engineer in charge. 110 mm dia 6Kgf/cm².

50.17.1.3 Supplying and fixing CP Towel rod 60cm or nearest available length including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.

50.17.1.1 Supplying and fixing Stainless steel soap dish including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.

50.17.1.5 Supplying and fixing CP Health Faucet superior quality (Jagur or equivalent make) including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.

50.18.7.3.1 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer- in- Charge 25 mm dia 12 Kgf/cm² - Internal work - Exposed on wall.

50.18.7.6.2 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 50 mm dia 6 Kgf/cm² - Internal work- Exposed on wall.

50.18.8.3.2 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 25 mm pipe 10 kgf/cm²

50.18.8.6.2 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 50 mm pipe 6 kgf/cm²

50.18.8.8.2 Providing and fixing PVC pipes, fittings, including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per the direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 75 mm pipe 4 kgf/cm²

50.18.8.9.1 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 110 mm pipe 6kgf/cm²

50.18.9.21.10 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes,including jointing with PVC solvent cement -75x63 mm dia Reducer.

50.18.9.22.9 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 mm dia offset

50.18.9.22.10 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 mm dia End Cap

50.18.9.22.11 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 mm dia Socket/coupling

50.18.9.8.2 Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching and refilling & testing of joints complete as per direction of Engineer in Charge. 75 mm dia 4 Kgf/cm²

50.18.9.13.2 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 25 mm dia 10 Kgf/cm² - External work - Exposed on wall

50.18.7.6.1 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 50 mm dia 10 Kfg/cm² - Internal work- Exposed on wall

50.18.8.6.1 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 50 mm pipe 10 kgf/cm².

50.18.9.6.2 Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 50 mm dia 6 Kgf/cm²

50.18.9.16.2 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 50 mm dia 6Kgf/cm² - External work - Exposed on wall

50.18.9.17.1 Providing and fixing PVC pipes including fixing the pipe with clamps/ clip at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 63 mm dia 6 Kgf/cm² - External work - Exposed on wall.

50.18.9.18.1 Providing and fixing PVC pipes including fixing the pipe with clamps/clips at 1.00 m spacing. This included jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 75 mm dia 6Kgf/cm² - External work- Exposed on wall

50.18.9.19.1 Providing and fixing PVC pipes including fixing the pipe with clamps/clips/ at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 110 mm dia 6 Kgf/cm² - External work- Exposed on wall

50.18.9.20.1 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 63 mm dia Elbow

50.18.9.20.2 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 63 dia 45 degree Elbow

50.18.9.20.10 Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes,including jointing with PVC solvent cement - 63x50 mm dia Reducer

50.18.9.21.4 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75 mm dia Bend

50.18.9.21.6 Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75x75x75 mm dia Door Tee.

50.18.9.21.9 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75 mm dia Socket/coupling

50.18.9.22.5 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes including jointing with PVC solvent cement 110x110x110 mm dia Tee

50.18.9.22.12 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110x75 mm dia Reducer

50.18.9.12.1 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 20 mm dia 12 Kgf/cm² - External work - Exposed on wall

50.18.9.13.1 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 25 mm dia 12 Kgf/cm² - External work- exposed on wall

50.18.9.14.1 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 32 mm dia 10 Kgf/cm² - External work- Exposed on wall

50.18.9.16.1 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 50 mm dia 10Kgf/cm² - External work - Exposed on wall

17.28.1.2 Providing and fixing P.V.C. waste pipe for sink or wash basin including PVC. waste fittings complete. Semi rigid pipe 40 mm dia

17.70.2 Providing and fixing PTMT Bottle Trap for Wash basin and sink. Bottle trap 38 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the center of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 263 gms .

18.50.1 Providing and fixing C.P brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 15 mm nominal bore.

18.22.2 Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet: 150 mm diameter

18.49.1 Providing and fixing C.P brass bib cock of approved quality conforming to IS: 8931. 15 mm nominal bore

18.51.1 Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore.

18.84.1 Providing & fixing chrome plated brass battery based infrared sensor operated pillar cock, having foam flow technology. 15 mm nominal bore.

18.53A Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge

18.21.1.1 Providing and fixing uplasticised PVC connection pipe with brass unions: 30 cm length 15 mm nominal bore

18.58.2.1 Providing and fixing PTMT grating of approved quality and colour. Rectangular type with openable circular lid 150 mm nominal size square 100 mm diameter of the inner hinged round grating

17.73.1 Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm. weighing not less than 170 gms

50.17.1.2 Supplying and fixing CP Towel rod 45cm or nearest available length including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.

12.41.2 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS: 13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter

50.18.9.10.1 Providing and fixing PVC pipes includings jointing of pipes with one step pvc solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 150 mm dia 6 Kgf/cm²

50.18.9.12.2 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 20 mm dia 10Kgf/cm² External work- Exposed on wall

50.18.7.3.2 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 25 mm dia 10Kgf/cm²- Internal work- Exposed on wall

50.18.9.7.1 Providing and fixing PVC pipes includings of pipes with one step PVC solvent cement, trenching refilling & testing of joints complete as per direction of Engineer in Charge. 63 mm dia 6Kgf/cm²

50.18.9.8.1 Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 75 mm dia 6 Kgf/cm²

18.52.1 Providing and fixing C.P brass stop cock (concealed) of standard design and of approved make conforming to IS: 8931. 15 mm nominal bore

50.18.9.21.7 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75 mm dia Vent cowl

19.4.1.1 Providing and fixing square-mouth S.W. gully trap class SP -1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:100x100 mm size P typeWith common burnt clay F.P.S. (non modular) bricks of class designation 7.5

19.7.1.2 Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand) with R.C.C. top with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix ( 1 cement : 4 coarse sand : 8 nnngraded stone aggregate 40 mm nominal size,) inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) finished with a floating coat of neat cement complete as per standard design: Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weigh of cover 23 kg and weight of frame 15 kg):With Sewer bricks conforming to IS : 4885

19.33 Constructing soak pit 1.20x1.20 m filled with brickbats including S.W. drain pipe 100 mm diameter and 1.20 m long complete as per standard design.

19.32.1 Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

51.19.ST4 Supplying and installing ready made PVC Septic tank including the cost of carriage, trenching, placing at the level below ground level as specified as per the direction of engineer in charge (Provision for CC/RCC/Sand/06mm aggregate for the preparation of bed shall be paid separately) 4. 35 to 50 flush capacity

18.48 Providing and placing on terrace (at all floor levels) polyethylene water storage tank :ISI 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

18.48A Providing and fixing rectangular high density polyethylene water storage loft tank with cover, conforming to ISI: 12701, colour of opaque white or as approved by Engineer-in-charge. The rate includes making necessary holes for inlet, outlet & over flow pipes. The base support i/c fittings & fixtures for tank shall be paid separately.

Electrical

1.10.1 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group A

1.24.3 Supplying and fixing following modular switch/socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 15/16 amp switch

1.24.1 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 5/6 amps switch

90.10.3.15 Supply and Fixing the following modular switches & accessories in the existing front plates and giving necessary connections as required (RoHS compliant )32A DP switch with indicator .

90.10.3.17 Supply and Fixing the following modular switches & accessories in the existing front plates and giving necessary connections as required (RoHS compliant )6A universal socket

90.10.3.22 Supply and Fixing the following modular switches & accessories in the existing front plates and giving necessary connections as required (RoHS compliant )6A 3 pin plug top

90.10.3.23 Supply and Fixing the following modular switches & accessories in the existing front plates and giving necessary connections as required (RoHS compliant )16A 3 pin plug top

90.10.3.24 Supply and Fixing the following modular switches & accessories in the existing front plates and giving necessary connections as required (RoHS compliant )Step Fan regulator - type 2 M

90.10.3.32 Supply and Fixing the following modular switches & accessories in the existing front plates and giving necessary connections as required (RoHS compliant )25A 3 pin plug top with indicator

90.10.3.33 Supply and Fixing the following modular switches & accessories in the existing front plates and giving necessary connections as required (RoHS compliant )25A 3pin Shuttered socket

1.21.1 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required. 20 mm

1.21.2 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm

1.21.3 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required. 32 mm

2.3.4 Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 16 way, Double door

2.4.1 Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)4 Way (4+12) Double door

2.5.1 Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's (but without MCB's and incomer) as required. (Note: Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 4 WAY(4+12), DOUBLE DOOR

2.4.2 Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)6 Way (4+18), Double door

2.15.2 Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 milli Amperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps

2.2.1 Providing and fixing following rating and breaking capacity MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel. making connections. etc. as required. 100 A, 16ΚΑ

9.1.23 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 70 sq. mm (38mm)

7.7.1 Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. Upto 35 sq. mm (clamped with 1mm thick saddle)

OD97355/2025-2026 Supply and installation of 1200 mm, 20 W LED tubelight with all accesssories as required. (Make:Crompton/Philips/Wipro)

OD97358/2025-2026 Supply & Installation of 1200 mm sweep BEE star rated ceiling fan, Features- 230V, no. of blades- 3, power consumption- min 50W, air flow capacity-above 210 Cfm, Blade type - rust proof /dust proof Aluminium blades, Speed - min 350 RPM, Efficiency- Energy Efficient, control type - button control, etc complete as required. (Brand : Crompton / Usha / Orient/ Havells/ Equivalent).

OD97365/2025-2026 Supply & Installation of Normal size 8 W BC/ ES LED bulb.(Make: Philips/ Crompton/ equivalent) Standard make and ISI Marked

90.4.3 Conveyance installation testing and commissioning ceiling fan of all sizes using standard accessories excluding resistance type regulator wiring the down rod with 16/0.20mm PVC insulated and PVC sheathed 650/1100V grade 3 core round copper conductor flex wire or extending the original wiring etc. as required.

90.4.8 Charges for cutting holes suitable for accommodating exhaust fans up to 305mm sweep including plastering colour washing etc. as required.

OD97378/2025-2026 Supply of 900 or more rpm, 300mm sweep 55 Watts exhaust fan of approved brand and manufacturer-Philips/Bajaj/Crompton/equivalent, Body- PVC, suitable for single phase 230V, 50Hz, AC supply, air flow capacity- 1125 Cubic meters/Hr, power source- corded electric with bird guard and other fixing accessories etc. complete as required.

1.50.1 Installation of exhaust fan in the existing opening, including making good the damage connection testing, commissioning etc. as required. Upto 450 mm sweep.

1.14.1 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2x1.5 sq.mm + 1x1.5 sq.mm earth wire

1.18.2 Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.2 Pair

1.53.1 Supplying and drawn of UTP 4 pair CAT 6 LAN cable in the existing surface/recessed steel/PVC conduit as required1 run of Cable

1.10.2 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group B

1.10.3 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch... as required. Group C

1.31 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings).

1.33 Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required.

1.14.2 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

1.14.3 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2 X 4 sq. mm + 1 1 X 4 sq. mm earth wire

1.14.4 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2 X 6 Sq.mm + 1 x 6 sq.mm earth wire

2.10.1 Supplying and fixing 5A to 32 A rating, 240/415 volts, 10 kA, ""C"" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

2.10.4 Supplying and fixing 5A to 32 A rating, 240/415 volts, 10 kA, ""C"" curve, miniaturecircuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Triple pole

2.13.1 Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

2.13.2 Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps

2.15.1 Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 milli Amperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.25 amps

2.15.3 Supplying and fixing following rating, four pole, (three phase and neutral), 41 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 milli Amperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps

5.1 Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (but without charcoal/ coke and salt ) as required.

5.17 Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing as required.

9.1.21 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 35 sq. mm (32mm)

9.1.32 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 10 sq. mm (25mm)

9.1.33 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 16 sq. mm (28mm)

7.7.2 Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)

2.19 Supplying and fixing 20 A,415volts, TPN industrial type, socket outlet, with 4 pole and earth, metal enclosed plug top along with 20 amps "C" curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

2.20 Supplying and fixing 30 amps, 415 volts, TPN industrial type, socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 amps "C" curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

90.14.5 Supply and fabrication conveyance and installation of angle iron frame work for wall mounting panel board

14.7 Providing and laying in position cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) in foundation of pump, DG set etc including form work etc as required.

90.14.1.2 Fabrication, supply, conveyance, installation testing and commissioning of floor or wall mounting, dust and vermin proof, cubicle type MV panel board comprising of the following components/ devices & complying to IS 8623.Fabrication of fully partitioned, dust and vermin proof enclosure for panel assembly as per form 4 of IS 8623 (with latest amendments) using CRCA sheet as per approved design and requirement, with front and rear access facility, bus bar chambers, hinged doors for all switch gear compartments, earthing the doors using 4 sq mm braided copper conductor, providing necessary cut-outs for mounting meters, relays, indication lamps, bus bar interconnection etc, detachable covers for bus bar chamber and cable alley, powder coating the assembly after subjecting to 7 tank process etc as required. CRCA sheet alone be used for the fabrication. Angles/ flats/ slotted angles etc shall not be used for the fabrication of panel assembly. The measurments will be taken the area of the complete sheets used for panel board including partitions, folding, shrouding etc.Supply and fabrication of MV panel board using 1.6mm CRCA sheet, powder coated (excluding base frame)

90.14.2.1 Supply and providing 2mm SMC sheet as shrouding for bus interconnection / terminations etc. including required nut & bolt etc.

90.14.3.1 Supply and providing heavy duty 'A' section neoprene gasket in the panel boardA' section neoprene beeding suitable for 1.60/2.00 mm sheet

90.14.4 Supply and fabrication conveyance and installation of base frame of panel board using 75x40 mm rolled steel channel (ISMC)

90.14.6 Supply and providing copper bus bars including finger type SMC bus bar supports in the bus chamber, suitable size nut & bolt, providng heat shrink sleeves etc. as required.

90.14.7 Supply and providing copper earth bus in the panel board

90.14.10.4 Supply, conveyance and fixing the following types & current rated control gears & switchgears conforming to IS 13947 suitable for 440 V, 50 Hz, AC supply in the existing panel assembly as required.16 A-100A, 25/35 kA (Ics=100%Icu), 4 pole,current limiting type MCCB having thermal setting range of 80 - 100% with thermal magnetic release having adjustable OL

90.14.10.11 Supply, conveyance and fixing the following types & current rated control gears & switchgears conforming to IS 13947 suitable for 440 V, 50 Hz, AC supply in the existing panel assembly as required.125A, 35/36 kA (Ics=100%Icu), 4 pole, current limiting type MCCB with microprocessor based release with overload setting of 50 - 100% having adjustable OL & SC

90.14.10.12 Supply, conveyance and fixing the following types & current rated control gears & switchgears conforming to IS 13947 suitable for 440 V, 50 Hz, AC supply in the existing panel assembly as required.160A, 35/36 kA (Ics=100%Icu), 4 pole, current limiting type MCCB with microprocessor based release with overload setting of 50 -100% having adjustable OL & SC

90.14.10.13 Supply, conveyance and fixing the following types & current rated control gears & switchgears conforming to IS 13947 suitable for 440 V, 50 Hz, AC supply in the existing panel assembly as required.200A, 35/36 kA (Ics=100%Icu), 4 pole, current limiting type MCCB with microprocessor based release with overload setting of 50 -100% having adjustable OL & SC

90.14.10.17 Supply, conveyance and fixing the following types & current rated control gears & switchgears conforming to IS 13947 suitable for 440 V, 50 Hz, AC supply in the existing panel assembly as required.320A/400A, 50/55 kA (Ics=100%Icu), 4 pole, current limiting type MCCB with microprocessor based release with overload setting of 50 - 100% having adjustable OL & SC

90.14.11.12 MCCB AccessoriesSupply and fixing shunt release for all voltage range up to 630A.

90.14.11.13 MCCB AccessoriesSupply and fixing rotary handle, External type (including BUC handle with door interlock) in the existing MCCB of rating up to 250 A

90.14.11.15 MCCB AccessoriesSupply and fixing rotary handle, External type (including BUC handle with door interlock) in the existing MCCB of rating up to 315-630 A

90.14.11.18 MCCB AccessoriesSupply and fixing kastel interlock kit 315 to 630A.

5.4 Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure... with charcoal/ coke and salt as required.

5.14 Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

OD97411/2025-2026 Fabrication, supply &amp; installation of dust and vermin proof, wall mounting, meter box of required size suitable for fixing KSEB meter,fuse units, CT etc, hinged door construction for the front side with compartments if necessary,providing vision panel for the meter compartment, knock out for cable entry and exit including 125A 4 pole Switch disconnector - 1 no, 100A Cut out Fuse - 3 nos,100/5A, Class 0.5s, 15VA Cast resin CTs - 4 Nos, neutral link etc complete as required at site

OD97413/2025-2026 Preparation of as-fitted drawings, computing the actual connected load, submitting the work completion report, obtaining power allocation & power connection from KSEB. All statutory payments will be reimbursed on production of the original receipts. The rate shall include the charge for preparation of SLD, laminating and displaying it in designated area

OD97415/2025-2026 SIGN BOARD -Providing and installing in position the following type of sign boards made out of 3mm thick rigid PVC board with computer cut with texts written to recommended height in photolumiscent material complete vide technical specifications with mirror fasteners. Sizes and mounting height of the board shall be as per technical specification. Fire Duct sign board 12' x 4'.

OD97416/2025-2026 SIGN BOARD Providing and installing in position the following type of sign boards made out of 3mm thick rigid PVC board with computer cut with texts written to recommended height in photolumiscent material complete vide technical specifications with mirror fasteners. Sizes and mounting height of the board shall be as per technical specification. No Smoking sign board 12' x 4'.

OD97417/2025-2026 : Providing and installing in position the following type of sign boards made out of 3mm thick rigid PVC board with computer cut with texts written to recommended height in photolumiscent material complete vide technical specifications with mirror fasteners. Sizes and mounting height of the board shall be as per technical specification. Fire Exit sign board 12' x 4' with arrow markings.

OD97524/2025-2026 Supply and providing 6 kg ABC DRY POWDER type fire extinguisher of approved brand and manufacture (Lifeguard/ Eco fire/Safeverse/Equivalent) with Wall hook, Discharge pipe, how to use sticker, expiry date certificate, hose and clamps including fixing it to wall as required.

OD97526/2025-2026 Supply and providing 9Litre water type fire extinguisher of approved brand and manufacture (Life guard/ Eco fire/Pyro guard/Equivalent) , Operating temperature-30 to +60 Celsius, minimum effective discharge-95%, fire rating- 3A, with Wall hook, Discharge pipe, how to use sticker, expiry date certificate , hose and clamps including fixing it to wall as required.

OD97528/2025-2026: Supply and providing 9 Litre capacity GI Fire Bucket painted in post office red with primer cost of redoxide and written with white paint 'FIRE' filled with fine sand, mounted on existing MS angle frame work/wall bracket etc as required

OD97531/2025-2026 Supplying, Installing, Testing & Commissioning of 2 way Fire brigade Inlet connection fabricated from 100 mm dia MS Class B medium grade pipe comprising of two 63 mm dia gun metal male threaded non return valve

OD97532/2025-2026 Supplying, Installing, Testing & Commissioning of Air release valve gun metal body as per IS:778. 20 mm dia .

OD97533/2025-2026 Supplying, Installing, Testing & Commissioning of Hose Box (Fire Hose cabinet) to accommodate one piece of 63 mm dia fire hose along with one piece of 63 mm dia male & female couplings and one branch pipe. The cabinet is made of M.S. powder coated with glass fronted hinged doors and lock.

OD97534/2025-2026 Supplying, Installing, Testing & Commissioning of Hose reel drum made of Mild Steel, with mounting brackets 19 mm dia nylon braded smooth surface rubber thermo plast hose 30 mtrs length with shut off nozzle.

OD97535/2025-2026 Supplying, Installing, Testing & Commissioning of Fire Fighting Hose , all synthetic fiber circular woven jacketed,control perculated delivery hose , 38kg/cm2 burst pressure, 22kg/cm2 proof pressure, 14 kg/cm2 working pressure, bearing IS:636-88 type B , in 15 mtrs length, 63 mm dia, duly bounded with SS coupling 63 mm dia pair of male & female parts, instantaneous type .

OD97536/2025-2026 Supplying, Installing, Testing & Commissioning of branch pipe made out of SS 63 mm short male instant. Inlet male threaded outlet, fitting with 15 mm bore nozzle ISI certified.

OD97537/2025-2026 Supplying, Installing, Testing & Commissioning of Hydrant valve 63 mm dia oblique type with SS body & working parts, with instantaneous hose coupling adaptor and PVC blank cap & chain.

OD97538/2025-2026 Supplying, Installing, Testing & Commissioning of Ball Valve as per IS 5312. 20 mm dia

OD97541/2025-2026 Supplying, Installing, Testing & Commissioning of Non Return Valve single plate wafer type slim seal check valve, short pattern type with integral hinge pin disc , nitrile rubber O - ring seat and face sealing as per IS: 5312 . 125mm dia

OD97542/2025-2026 Supplying, Installing, Testing & Commissioning of charges for High Pressure switch arrangement for pump room and total system (model- Danfoss Kp 36/equivalent.), operation- automatic, contact type- normally open, circuit type- 1 way, control- push button, switch type- pressure switch.

OD97543/2025-2026 Supplying, Installing, Testing & Commissioning of charges of Pressure gauge arrangement for pump room and total system (Dia 100mm/nearest available size), material -composite of aluminium, brass, glass, body- metal.

OD97544/2025-2026 Supplying, Installing, Testing & Commissioning of Automatic fire hydrant system panel for Terrace pump of standard specification and ISO certified and approved brand.

OD97545/2025-2026 Supplying and installing of in position the following type of sign boards made out of 3mm thick "Opaque" PVC foam board with computer cut, PVC Non-reflective self adhesive vinyl painted foam board, complete with mirror fasteners.

OD97547/2025-2026: Supplying and installing of in position the following type of sign boards made out of 3mm thick "Opaque" PVC foam board with computer cut, PVC Non-reflective self adhesive vinyl painted foam board, complete with mirror fasteners. EVACUATION PLAN

OD97548/2025-2026 STATUTORY APPROVAL Complete services from the contractor for liasoning works such as filing necessary applications, submission of forms for approval to local fire authorities, depositing the fees / other amounts as required for getting the premises / installations, inspected and approved and all other formalities required till approved by Local Fire Authorities. All the expenses incurred in this regard shall be borne by the Contractor. The official payments to be made for any security deposit etc. in this regard which shall be reimbursed on production of original voucher.

OD97549/2025-2026 Supplying, Installing, Testing & Commissioning of electrically operated Terrace Pump of 450LPM capacity 24 MWC, high efficiency volute type with cast iron casing, cast iron impeller, pump coupled with a squirrel cage induction motor TEFC type with a supply condition of 415 V 50 Hz foot mounted type for Suitable 5HP at 1350 RPM 3 kg including base plate coupling guard and all other necessary accessories.

OD97552/2025-2026 Supplying, Installing, Testing & Commissioning of butterfly valve wafer type Stainless steel/SG iron disc , lever operated as per IS:13095 in PN 1.0 , teflon or nylon bushing, nitrile O rings in standard mounting flanges with hand lever type. 110mm dia

OD97553/2025-2026 Under Ground Piping- Supplying, Installing, Testing & Commissioning of underground piping M S pipe Class 'B' medium grade ISI mark complete with all necessary fittings such as nuts & bolts, bends, flanges, tees etc . and piping shall have anti corrosive wrapping treatment. 100 mm dia

OD97554/2025-2026 Above Ground Piping-Supplying, Installing, Testing & Commissioning of MS 'B' class medium pipe as per is medium grade of following dia, with necessary fittings such as nuts & bolts, bends, flanges ,etc and Welded joints, The pipe shall be painted with two coats red colour enamel paint over primary coat of Primer. 80mm dia.

OD97555/2025-2026 Above Ground Piping- Supplying, Installing, Testing & Commissioning of MS 'B' class medium pipe as per is medium grade of following dia, with necessary fittings such as nuts & bolts, bends, flanges ,etc and Welded joints, The pipe shall be painted with two coats red colour enamel paint over primary coat of Primer. 100 mm dia

OD97556/2025-2026 Supplying, Installing, Testing & Commissioning of butterfly valve wafer type Stainless steel/SG iron disc , lever operated as per IS:13095 in PN 1.0 , teflon or nylon bushing, nitrile O rings in standard mounting flanges with hand lever type. BUTTERFLY VALVE - 80 mm

Solar

OD97568/2025-2026 Supply, Installation, Testing and Commissioning of 40kWp On Grid Solar Power Plant with 19 Nos of 540 WP mono perc half cut (non-DCR) Solar panel module of approved make (Adani/ Waree Solar/Tata power/ equivalent), PCU/invertor-40KW three phase with wifi (for online monitoring) BIS certified approved brand (Polycab/Deye/Havells/equivalent), ACDB(AC Distribution box)-& DCDC(DC Distribution box)- IEC standard IP65 box with MCB SPD and fuse unit, DC cable- 10 sqmm UV rated 1500 V solar cables, 4 set of earthing and lightening protection- Excel earthings with ISI certified, copper bonded earth rod, 10swg copper, multispoke lightening arrester, 50 sq mm AI ground conductor chemical earth compound including system components having ISI standing meter box, isolator, connectors, pipe and accessories, Mounting structure- lattice type module mounting structure with epoxy coated GI frame(Excluding the cost of armoured cables to control panel, KSEB fee for feasibility report & registration, KSEB NET METER).

Generator

OD97648/2025-2026 Supply, Installation, Testing and Commissioning of 82.5 kVA Three Phase Diesel Genset of approved brand (Ashok Leyland(CPCB IV+ H4G4DE82) /Mahindra(mPower41015G)/Cummins(C82.5D5P)/Equivalent), Cooling systemwater cooled type, Engine- four stroke Turbo charged diesel engine, battery capacity- 90 Ah, engine rated -78/104(KW/HP), electric start D.G Set with acoustic enclosure and standard control panel with 125A 4P MCCB with stand by low earth fault relay using Neutral CT, additional battery charger, Voltage regulator, ammeter, voltmeter... indication lamp etc, Frequency- 50Hz, Insulation class- Class H or F, Protection- IP 23/IP 44 The engine shall be capable of taking 10% overload for one hour after 12 hours of continuous operation, Alternator - brushless synchronous type, self regulated, SPDP enclosure, class F/H insulation, suitable for continuous operation at 1500 rpm, Voltage- 415 V +/- 5% at 0.8 p.f, 0.80 load factor, fuel tank capacity- not less than 145Ltr, weight- 1417 KG, Noise level-75db, range of Fuel Consumption-12-18Lr/hr (at 100% full load), rated output range-77.2-105 kW, speed-1500mm/m, wire system generally conforming to BS: 2613 & IS: 4722. The neutral of the DG set shall be provided with low set earth fault relay using adequate Neutral CT in the neutral earthing conductor. Both Engine and Alternator shall be mounted on common channel iron base frame, and with standard accessories such as anti-vibration pad, lead acid batteries (as specified by engine manufacturer) and engine driven battery charger along with leads, battery stand, fuel etc, Size -2850Lx1300Wx1510H (mm)/compatible etc complete.excl the cost of foundation (asspecified by engine manufacturer) and engine driven battery charger along with leads, battery stand, fuel etc, Size - 2850Lx1300Wx1510H (mm)/compatible etc complete.excl the cost of foundation

90.6.5.4 Supply and drawing the following sizes of multi-core PVC insulated & FRLS PVC sheathed 650/1100 V grade copper conductor round flexible cables conforming to IS 694 part I 1960 in the existing surface / recess conduit as required including giving necessary connections of the following sizes. 2 core 1.50 sq mm

90.6.5.18 Supply and drawing the following sizes of multi-core PVC insulated & FRLS PVC sheathed 650/1100 V grade copper conductor round flexible cables conforming to IS 694 part I 1960 in the existing surface / recess conduit as required including giving necessary connections of the following sizes. 4 core 1.50 sq mm.

90.12.1.30 Supply & laying of one number PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in ground including excavation of trench of size 35 x 75 cm, refilling the trench etc. as required butexcluding sand cushioning and protective covering (in ordinary soil).3.5 core 70 sqmm

90.16.1.3 Supply and drawing bare earthing conductors of the following sizes along with wiring/cables and giving connection as required 3.15 mm copper conductor (10 SWG)

5.3 Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. (but without charcoal/ coke and salt ) as required.

5.8 Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

OD97656/2025-2026 Preparation of as-fitted drawings, computing the actual connected load, submitting the work completion report, obtaining power allocation & power connection from KSEB. All statutory payments will be reimbursed on production of the original receipts. The rate shall include the charge for preparation of SLD, laminating and displaying it in designated area

Furniture

OD97661/2025-2026 Supply and providing Executive High back revolving chair- Head rest height and angle adjustable. Seat Height adjustment Back rest angle Adjustable. Armrests 3d multi-function. Back upholstered with nylon mesh. Seat upholstered with nylon mesh. Multi -function 3 class locking mechanism. Powder coated/Electro plated TUV-CLASS 4 Gas spring 120mm, Aluminum base with PU castors:330mm Tested as per BIFMA X5.1 standards including cost and conveyance of all materials and labor charges for making.

OD97663/2025-2026 Supplying and Providing Executive Table using 16mm Marine Plywood conforming to ISO-9001-2015/ISO 14001-2015/BS 1088-2003 and 1 mm Mica finish, 2mm PVC Edge band, in the right hand side using hinged doors ; top with a sliding drawer, keyboard drawer; Stainless steel soft close telescopic channel & soft close hinges of approved brand ( EBCO or equivalent) ; 100 mm size SS handles ; locking facility ( ISI),provision for CPU/UPS etc. as per approved drawing details including cost and conveyance of all materials and labor charges for making , fixing the table etc complete.- Minimum height of table to be supplied-75cm - (Measurement to be made for top surface area)

OD97668/2025-2026 Supplying and Providing storage cupboard Using Marine plywood 16mm conforming to ISO 9001-2015/BS 1088-2003/ASTM D7295-14 standards and 1 mm Mica finish, 2mm PVC Edge band all complete as per the direction of engineer in charge and as per the drawing produced.

OD97669/2025-2026 Supply and Providing Teapoy Using Marine plywood 16mm with ISO/ISI-9001-2015 and 1 mm Mica finish, 2mm PVC Edge band, size of - 90Lx45Wx60H cm including cost and conveyance of all materials and labor charges for making.

OD97670/2025-2026 Supply and Providing Two seater Sofa cushioned - Seat & backrest upholstered with leatherette 14 Gauge pipe 1.25 thickness Powder coated/ electro plated chrome mild steel cantilever base. Tested as per BIFMA X5.1 standards including cost and conveyance of all materials and labor charges for making.

OD97674/2025-2026: Supply and providing Visitors chair, cushioned seat and back, Backrest, mild steel frame powder coated and upholstered with nylon mesh Armrest fixed- PP with fiber. Seat upholstered with imported fabric. 2.1mm thick, fixed round tube Powder coated/ electro plated chrome mild steel cantilever base. Tested as per BIFMA X5.1 standards including cost and conveyance of all materials and labor charges for making.

OD97675/2025-2026 Supply and Providing Single Cot hardwood bed with plank top, material- Teak/oak/maple/other durable hardwood material conforming to ISO 9001-2015/approved quality in make, Frame- solid hardwood frame with mortise and tenon joints, Slats- hardwood slats for support and ventilation, Headboard- as per requirement, Hard wood single cot with plank top - 190*90*45 cm

OD97676/2025-2026 Supply and Providing Single bed mattress with pillow of approved brand and manufacturer(Nilkamal/Dunlop/Repose/equivalent), Product dimension-183 L x 91W x 13Th (cm), Item weight not less than 7 kgs, Upholstery material- Polyurethane, Fill material- High density Foam, other features- three layer mattress with PU foam layer and knitted fabric cover. etc. complete.

OD97686/2025-2026 Providing and Fixing Beside Cupboard:- Material- Particle board/solid wood conforming to ISO 9001-2015/BS 1088 /ASTM D 3023/Approved quality ensured with 1 mm mica top finish, Finish- laminated finish, drawers-2-, size -45*45*45 cm.

OD97748/2025-2026 Supply and Providing Semi Fowler Bed of approved brand and manufacturer/ISO certified product, Material- Mild steel, Size : 1980Lx900Wx600H mm(Approx) Style : Basic, Finish type powder coating -min. 50microns, Item weight - not less than 40Kgs, Maximum weight-500 Kgs. etc complete(Excl the cost of semi fowler mattress).

OD97749/2025-2026 Supply and Providing Semi Fowler mattress with pillow, Weight- not less than 4 Kgs, Size- 75"Lx35"Wx 4"Th, Comfort level: High resilience grade 40 density polyurethane foam (PU), Support layer: EPE Foam, Comfort level- Soft, Upholstery material- polyester, product feature- foldable & breathable. etc complete

OD97757/2025-2026 Supply and Providing 6 Seater Stainless Steel Dining table, SS grade- SS 304(, Size - 180Lx90Wx75H cm, with foldable type SS seaters. etc all complete.

OD97759/2025-2026 Supplying and Providing Stainless Steel 2 Tier Trolley with 10 cm deep tray, 4 side 15cm splash, Shelf- 2 tiered shelf, 4 swivel Castors wheel with brake, material- frame & body- SS 304 grade, load capacity-20-30Kgs, Size - 90x60x85+15 (cm). etc Complete

OD97761/2025-2026 Supply and Providing Stainless Steel work table, Body- SS 304, Size range- 150x60x80cm, shelves- 2(excl top), weight - approx 22-28kgs, support leg-4/6 nos, sturdy frame for supporting heavy loads, uses- cutting, chopping, mixing and assembling dishes, suitable for commercial kitchens, labs, work shops, etc complete.

OD97763/2025-2026 Design, Supply, Fabrication and Installation of 12 mm thick HPL(High-Pressure- Laminate) sheet of approved brand and manufacturer for fabrication of cubicle type partitioning with composite laminated HPL sheet, sheet shall conforming to ISO 4586/ASTM E162/BS EN 438 standards, sheet shall be fixed with SS Gravity hinges, SS Adjustable leg, SS coat hook, SS door knob, aluminum U channel, SS lockset with indicator, aluminum anodized top rail, aluminum door stopper channel, SS 304 graded screws, wall plugs, noise deafening tapes for grooves in doors & pilasters etc. complete. The rate includes all cost of materials, labour charges for fabrication of the cubicle and the measurements will be taken the area of the complete sheets used.

OD97768/2025-2026 Supply and Providing 3 Burner Indian Cooking range, Size- 165x60x80+10, Burner specifications- 3 Nos of high pressure high efficiency burners, 6/4 LEG GRID, Body material- SS 304, Burner material- cast iron, 1 under shelf, Back side splash, weight - approx 45 kgs, power source- gas, No. of Knob- 6, etc complete.

OD97770/2025-2026 Supply and Providing Single Burner Indian Cooking range, Body - SS 304, Burner material- cast iron, no. of burner-1, shape- square, burner specification- high pressure burner in pan support- approx-60x60x45cm, weight approx -15-20kgs, no. of knob- 2, gas type - LPG, support- 4 nos of legs, storage rack and back flash. etc complete.

OD97771/2025-2026 Supply and Providing Two Burner Indian Cooking range, Body - SS 304, Burner material- cast iron, no. of burner-2 with pan support, shape- rectangular, burner specification- high pressure burner - approx-110x60x80+10 cm, weight approx -35-40 kgs, no. of knob- 4, gas type - LPG, support- 4 nos of legs, storage rack and back flash. etc complete.

OD97774/2025-2026 Supply and Providing Stainless steel utility sink free standing single sink unit with back flash, Body - SS 304 grade, bowl- single bowl with under shelf, size- 110x60x80+10 cm, sink bowl size- 39x33x22 cm, weight- approx 23-28 kgs, other features- heavy duty, multipurpose, heavy load capacity, polished surface finish. etc complete.

OD97775/2025-2026 Supply and Providing SS 304 graded Dosa burner range, size 1200x750x850+100 mm, 20mm dosa plate, no. of knob- 2nos, leg-2 nos.

OD97777/2025-2026 Fabrication, Installation, Testing and Commissioning of GI ducting for Fresh air with pre-filter/activated carbon/electrostatic/filter units, Sheet thickness - 26 G/22 G GI sheet, material- Galvanized iron sheet of ISI approved approved brand (JSW/tata/equivalent) and conforming to ISO 9001-2015, GST coating -120 GSM, Other feature- Highly durable- non corrosive, proper sealed with sealants(leak proof), air tight, connection b/w duct sheets by flange connections. etc complete..

OD97778/2025-2026 Fabrication, Installation, Testing and Commissioning of GI ducting for kitchen exhaust hood with grease/carbon/electrostatic filter units, Sheet thickness - 26 G/22 G GI sheet, material- Galvanized iron sheet of ISI approved brand (JSW/tata/equivalent) and conforming to ISO 9001-2015, GST coating -120 GSM, Other feature- Highly durable- non corrosive, proper sealed with sealants(leak proof), air tight, connection b/w duct sheets by flange connections.

OD97779/2025-2026 Supplying and Fixing Powder coated aluminium fresh air grill, powder coating -min 50 microns, thickness of louvers 1.5 to 3 mm, air flow rate-upto 1000 CFM, velocity- upto 500 fpm, mounting type - clip/screws, weatherproof coated grill to prevent weather & corrosion. etc complete.

OD97780/2025-2026 Supply and Installation of 5/8 inch Brass LPG Ball Valve of approved brands and ISO certified.

OD97781/2025-2026 Supply and Installation of GAS Pipe Line made up of MS threaded C Class pipe, TATA or Jindal Make including enamel painting of two or more coats as per engineers instructions.

OD97782/2025-2026 Supply and Installation of LPG Copper pipe with brass connector on both sides, Length up to 1 meter and 3/8 inch thread of approved brands.

OD97784/2025-2026 Supply and Installation of LPG Hose tube up to 1.5m long. ISI certified.

OD97785/2025-2026 Supply, Installation, Testing and Commissioning of Stainless Steel Kitchen Exhaust Hood with Filter, Body material-SS 304 grade 18/19G, capacity- 1200m3/h, suction capacity-600 CFM, size-600mm x500mm, style- wall type, Product type- exhaust hood with detachable oil collection tray and baffle filter. etc all complete(length of hood as per site requirement- actual quantity will be measured in metres).

OD97786/2025-2026 Supply and Fixing 1 HP Heavy Duty 24 inch Axial Flow fan for exhaust system, power -1HP, 3 phase, body material-mildsteel/cast iron, blade material- aluminium alloy, voltage-415 Volts, blow type- axial, air flow capacity-5000 m3, electric current type-AC, Fan speed -RPM, No. of blades-4/6, mounting type -duct, shapedrum shape, CFM- above 6000. etc all complete.

OD97787/2025-2026 Supply and Providing 6 pot Stainless Steel Bain Marie, Body - SS 304 grade, power - 3 kW, Weight approx - 20-25 Kgs, Voltage- 230V, Frequency -50Hz, Phase- Single phase, No. of pots- 6,Pot capacity- Approx. 6-8 L, size of GN pan-9.5 inch dia, 8 inch depth, support -4/6 legs, shelf-1 under shelf and provision for electrical connection with thermostat. etc complete.

OD97788/2025-2026 SITC of 18 '' Single phase axial fan sunction, material- metal, wattage- 135 watts, no. of blades-4/5, speed- 1350 RPM, voltage-220V, power source- corded electic, control- button/remote, mounting type- wall/ceiling, item weight not less than 0.9 Kgs. etc complete

OD97789/2025-2026 Supply and Providing Electric Hot Plate:- 120x75x85+10cm With 120x 68 x 2 cm SS 202 grade plate, Wattage- 3000 Watts, voltage-220 Volts, Knob-4, non - stick coated, 7 temperature control, Oil drainage, fire window Etc. Bottom cross support.

OD97791/2025-2026 Supply and Providing 3 Star rated Refrigerator with digital inverter, compressor- Digital Inverter compressor, Power-AC 220-240 V, Power Consumption-240-260 W, Frequency -50 Hz, cooling refrigerant- R-600/Equivalent, capacity -above 300 L, type- De frosting type, top mount, air flow- twin cooling plus/equivalent, double door, conforming to BEE rating, energy efficient and saver with cool pad, including toughened glass shelves, stabilizer- inbuilt type, weight not less than 50Kgs, Size range- 60L x 67Wx 1630H (cm)/compatible etc. complete

OD97827/2025-2026 Supply, Installation, erection, and commissioning of Normal, Cold, Water Dispenser having total storage capacity 80 litres, of approved brand SILVERMIST / BLUE STAR/ VOLTAS/ Equivalent, storage tank and the outer cabinet are made of stainless steel of grade 304 and 204, having dimension 45Dx55Wx125H in cm with weight upto 40kg, with three Taps and one 10" filter housing with spun, power consumption-200 Volts, equipped with a hermatically sealed, reciprocating compressor and R 134s refrigerant for reliable and consistent cooling performance, along with electrical and plumbing accessories like Electrical wires, switches, box, plate, pipes fittings, and plumbing pipes, fittings, including electrical and plumbing charges, all complete as per the direction of Engineer in charge

OD97836/2025-2026 Supply, Installation, erection, and commissioning of UV Water Purifier having storage capacity 12 litres, up to 50 Litres/Hour, of approved brand BLUE MOUNT/ HAVELLS/ AQUA GUARD/ Equivalent, 5 stage purification, wall mounted, with dimension 415x270x540mm, power consumption-20 Volts, including flitres are sediment, Active Carbon, Ultra Filtration, UV, Post Carbon with Tap having approximate weight of 4.5kg, along with electrical and plumbing accessories like Electrical wires, switches, box, plate, pipes fittings, and plumbing pipes, fittings, including electrical and plumbing charges, all complete as per the direction of Engineer in charge.

OD97837/2025-2026 Supply and Fixing Premium Quality Zebra Roller Blinds, Material- Polyester Blend/Polyster material @ 280GSM, Opacity- Light Filtering Inches/sheer, Pattern - Solid/equivalent, mounting type-Inside wall mount, operation mode - manual, Control Type - Cord control, aluminium brackets & railings, Features- High Quality/ durable/UV protection/stain resistant/Light Filtering, Application for Office. room, drawing room,etc complete.

OD97841/2025-2026 Providing and Fixing Cup board/Shelves with 17mm thick WPC(wood polymer composite) panel board conforming to ISO 9001-2015/ISO 14001-2015/ASTM D7295-14 standards and covered with 1mm mica at both sides & having 2mm edge band, fixing with screws and fittings etc, materialfoamed/ solid/textured/embossed WPC panel board, finish- laminate/UV coated/veneer, density-0.8-1.2 g/cm3, tensile strength -10-20MPa, water absorption - <5%, impact resistance-10-20 kJ/m2, flexural strength-20-30 MPa. etc complete.

OD97848/2025-2026 Supplying and fixing in wardrobe made with good quality 18mm thick laminated marine plywood with 1mm mica conforming including doors fixed by good quality auto close hinges,ss handle, lock and key arrangement all complete as per the direction of engineer in charge and as per the drawing produced.

Item Rate BoQ

BoQ_Ver4.0

Name of the Bidder/ Bidding Firm / Company :

(This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only)

NUMBER #

ESTABLISHING MODERN TRAINING INFRASTRUCTURE AT SFTI WALAYAR - EXECUTIVE ACCOMODATION

Civil Works

2.31 Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared

2.8.1 Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

2.6.1 Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5m, as directed by Engineer-in-charge.All kinds of soil

2.26.1 Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials.All kinds of soil

2.25 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

50.2.25.1 Filling with contractor's own earth ( excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m as per direction of site Engineer-in-charge

51.2.3 Filling with Quarry Muck Filling up low lying and water logged areas with local material/ quarry muck, spreading in layers, leveling the top at site and consolidation by ramming, etc complete for improving the CBR value of subgrade

4.1.8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

4.1.5 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources)

4.1.3 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-III)derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

60.7.1 DRY RUBBLE MASONRY _ Dry rubble without concrete levelling course masonry with good quality blasted rubble including packing to compactness to lines and levels cost and conveyance of all materials labour charges etc. complete as per direction of Departmental officers at site

7.1.1 Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand)

5.1.2 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work upto plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size derived from natural sources)

5.22.6 Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

5.9.1 Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.7 Centering and shuttering including strutting, etc. and removal of form for:Stairs, (excluding landings ) except spiral - staircases)

5.9.2 Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.9.19 Centering and shuttering including strutting, etc. and removal of form for:Weathershade, Chajjas, corbels etc., including edges

5.11.1 Extra additional height in centering, shuttering where ever required with adequate bracing, propping etc. including cost of de-shuttering and decentering at all levels, over a height of 3.5m, for every additional height of 1 metre or part thereof (Plan area to be measured).Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)

5.2.2 Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up tot floor five level excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

26.30.1 Drilling suitable holes in reinforced or plain cement concrete with power driven drill machine to a minimum depth of 100mm upto 200mm in RCC beams, lintels, columns and slabs to introduce steel bars for sunshades/balconies including fixing the steel bars in position using epoxy resin anchor grout of approved make but excluding the cost of reinforcement, all complete as per direction of Engineer-In-Charge.Upto and including 12mm dia.

5.3 Reinforced cement concrete work in beams, suspended floors, roofs, having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with1:1.5:3 (1 cement : 1.5 coarse sand (Zone III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources).

5.22A.6 Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo - Mechanically Treated bars of grade Fe-500D or more

5.9.6 Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts

5.9.5 Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.9.3 Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.9.16.1 Centering and shuttering including strutting, etc. and removal of form for: Edges of slabs and breaks in floors and wallsUnder 20 cm wide

4.11 Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20mm nominal size derived from natural sources).

4.17 Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

50.6.1.5 Solid block masonry using pre cast solid blocks ( Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 Part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement : 6 coarse sand) etc complete

50.6.1.4 Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 part I of 1979 for foundation and plinth with thickness 20cm and above in: CM 1:6 ( 1 cement : 6 coarse sand ) etc complete

50.6.2.2 Solid masonry using pre cast solid blocks (factory made) of size 30x20x15cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level with thickness 15cm in : CM 1:6 ( 1 cement : 6 coarse sand) etc complete

50.6.3.2 Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x10 cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level for 10 cm thick wall in : CM 1:6 ( 1 cement : 6 coarse sand) including cost of scaffolding complete

6.47 Providing and laying Autoclaved Aerated concrete (AAC) blocks masonry 150mm/230mm/300 mm thick with Grade- I AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).

6.15 Extra for providing and placing in position 2 Nos 6 mm dia M.S bars at every third course of half brick masonry.

13.1.1 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

13.16.1 6 mm cement plaster of mix:1:3 ( 1 cement : 3 fine sand)

13.2.2 15 mm cement plaster on the rough side of single or half brick wall of mix:1:6 ( 1 cement : 6 fine sand)

13.7.1 12 mm cement plaster finished with a floating coat of neat cement of mix:1:3 ( 1 cement : 3 fine sand)

13.18 Neat cement punning

5.30 Add for plaster drip course / groove in plastered surface or moulding to R.C.C. projections.

13.76 Forming groove of uniform size from 12x12 mm and upto 25 x 15 mm in the top layer of washed stone grit plastered surface as per approved pattern, including providing and fixing aluminum channels of appropriate size and thickness (not less than 2 mm), nailed to the under layer with rust proof screws and nails and finishing the groove complete as per specifications and direction of the Engineer -in-Charge.

13.29.3 18 mm thick plain cement mortar band in cement mortar 1:4 ( 1 cement : 4 fine sand):Raised Band

9.1.1 Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).Second class teak wood

2.34.1 Supplying chemical emulsion in sealed containers including delivery as specified.Chlorpyriphos / Lindane emulsifiable concentrate of 20%

2.35.3.1 Diluting and injecting chemical emulsion for POST -CONSTRUCTIONAL antitermite treatment (excluding the cost of chemical emulsion): Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floor:With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

10.17 Providing and fixing M.S. fan clamp type I or II of 16 mm dia M.S. bar, bent to shape with hooked ends in R.C.C. slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete.

OD88326/2025-2026 [Derived From DSR 9.21.1] Providing and fixing ISI marked flush/panelled door shutters with hardwood conforming to ISO 8271/ ISO 8272/ISO 9001/ISO 14001 & of decorative Type, hardwood with frame of 1st class hardwood board and well matched commercial 1mm thick decorative mica lamination on both faces of shutters and 2mm thick edge band, finishteak/ laminated/compatible: 30-35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws (Cost of glazing shall paid extra and portion of glazing shall deduction from measured area) Details of cost for 2.2 sqm

9.7.7.1 Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured), Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick:4 mm thick glass pane (weight not less than 10kg/sqm).

9.7.7.2 Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured), Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick:5.0 mm thick glass panes (weight not less than 12.50 kg/sqm).

9.165.1 Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete.125 mm

OD88396/2025-2026 Providing and fixing stainless steel hanging type floor door stopper with necessary screws, etc. complete. 150mm long

OD88399/2025-2026 Providing & Fixing stainless steel sliding door bolts with nuts and screws etc complete

OD88403/2025-2026 Providing and fixing stainless steel tower bolts with necessary screws etc. complete

9.76 Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

9.53 Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

9.153 Providing and fixing steel (white power coated) crescent lock for uPVC sliding window/ door with necessary screws etc. complete.

9.147A.2 Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 +/ 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Casement window double panels with S.S. friction hinges (300 x 19 x 1.9 mm) made of (small series) frame 47 x 50 mm, sash 47 x 68 mm & mullion 47 x 68 mm all having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area of window above 0.75 sqm upto 1.50 sqm).

9.147A.3 Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 +/ 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Casement window double panels with top fixed with S.S. friction hinges (350 x 19 x 1.9 mm) made of (small series) frame 47 x 50 mm, sash 47 x 68 mm & mullion 47 x 68 mm all having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. ( Area of window upto 2.50 sqm).

9.148.1 Providing and fixing stainless steel (SS-304 grade) friction hinges to the side/ top hung uPVC windows, of approved quality, with necessary stainless steel screws etc. as per direction of Engineer - in-charge.200 x 19 x 1.9 mm

9.148.2 Providing and fixing stainless steel (SS-304 grade) friction hinges to the side/ top hung uPVC windows, of approved quality, with necessary stainless steel screws etc. as per direction of Engineer - in-charge.250 x 19 x 1.9 mm

9.148.4 Providing and fixing stainless steel (SS-304 grade) friction hinges to the side/ top hung uPVC windows, of approved quality, with necessary stainless steel screws etc. as per direction of Engineer - in-charge.350 x 19 x 1.9 mm

9.149 Providing and fixing casement handle made of zinc alloyed (white powder coated) for uPVC casement window with necessary screws etc. complete.

9.150 Providing and fixing zinc alloyed (white powder coated) touch lock for uPVC sliding window with necessary screws etc. complete.

9.151 Providing and fixing steel roller for uPVC sliding window with necessary screws etc. complete.

9.152 Providing and fixing steel roller for uPVC sliding door with necessary screws etc. Complete.

9.147B.1 Providing and fixing factory made uPVC white colour fixed glazed windows/Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.)

21.3.2 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5.50 mm thickness (weight not less than 12.50 kg/sqm)

21.3.1 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm)

OD88405/2025-2026 Filling the gap between aluminium/stone/wood frame and adjest RCC/Brick/Stone/Wood/Ceramic/Gypsum work by providing weather structure non sag elastomeric Hybrid PU Sealant of approved brand and manufacturer (Asian paints smartcare/Loctite/Dr. Fixit/Equivalent) over backer rod of approved quality as per architectural and direction of Engineer-in-charge complete

9.71.1 Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc. complete:125x64x2.50 mm

9.71.3 Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc. complete:75x50x2.50 mm

9.71.3 Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc. complete:75x50x2.50 mm

9.143 Providing and fixing factory made uPVC door frame, made of uPVC extruded section, of size 65 mm x 55 mm with wall thickness 2.0 mm (? 0.2mm), corners of the door frame to be mitred cut and jointed with plastic brackets and stainless steel screws, reinforcing hinge side vertical of the frames with PVC profile of Size 28 mm x 30 mm having wall thickness 2 mm ( ? 0.2 mm), including providing & fixing 3 nos of 125 mm long stainless steel hinges to the frame, fixing the frame with jamb with required number & size of anchor dash fastners, all complete as per manufacturer's specification and direction of Engineer-in-charge.

9.147C.1 Providing and fixing factory made uPVC white colour casement/ Casement cum fixed glazed door comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 +/- 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealent shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Casement door with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 +/- 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.00 sqm).

10.26.3 Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approves steel primer.G.I. pipes

10.16.1 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes

10.28 Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)

10.2 Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

13.52.1 Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work

8.2.2.2 Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Area of slab over 0.50 sqm

8.3.2 Providing edge moulding to 18 mm thick marble stone counters, vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer -in-Charge.Granite work

11.52.1 Providing and laying machine cut, mirror polished Marble stone flooring, in required design (Simple geometrical, abstract etc.) and in patterns in combination with Italian marble stone of different colours, shades and finished surface texture etc., in linear portions of the building, all complete as per the shades and finished surface texture etc., in linear portions of the building, all complete as per the architectural drawings, with 18 mm thick stone slab laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm including pointing with white cement slurry admixed with pigment to match the marble shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-charge. a. 18 mm thick Italian Marble stone slab, Perlato, Rosso verona, Fire Red or Dark Emperadore etc.18 mm thick Italian Marble stone slab, Periato, Rosso verona, Emperadore etc.

9.48.2 Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings/ wooden frames with rawl plugs screws etc

8.5 Extra for providing opening or required size & shape for wash basin/kitchen sink in kitchen platform, vanity counter and similar location in marble/granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

OD88481/2025-2026 Providing & applying one componet polyurethene, waterproofing liquid memberane on terrace. PU is applied by brush or roller in two layer. Epoxy primer should be dry and surface moisture should be less than 4% before PU application. The first layer is applied 2-3 hours after primer and while PU epoxy primer is still dried. The second layer should be applied crosswise after 8-24 hours, depending on the weather conditions. ( Epoxy primer - 200 gm per sqm and PU per coat should be 650 gm/sqm). The rate shall include all labour, material and coveyance charges etc complete.

22.1.1 Providing and laying integral cement based treatment for water proofing on horizontal surface at all depth below ground level for under ground structures as directed by Engineer-in-charge and consisting of :i ) Ist layer of 22 mm to 25mm thick approved and specified rough stone slab over a 25 mm thick base of cement mortar 1:3 ( 1 cement : 3 coarse sand) mixed with water proofing compound conforming to IS: 2645 in the recommended proportion over the leveling course ( leveling course to be paid separately). Joints separately) joints sealed and grouted with cement slurry mixed with water proofing compound. II) 2nd layer of 25 mm thick cement mortar 1:3 ( 1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportions. iii) Finishing top with stone aggregate if 10 mm to 12 mm nominal size spreading @ 8 cudm/ sqm thoroughly embedded in the 2nd layerUsing rough kota stone

22.3 Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C. kitchen and the like consisting of : i) I course of applying cement slurry @ 4.4 Kg/ sqm mixed with water proofing compound conforming to IS: 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. ii) II course of 20 mm cement plaster 1:3 ( 1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. iii) III course of applying blown or residual bitumen applied hot at 1.7 kg per sqm of area. iv) IV course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 Kg/ sqm.

OD88489/2025-2026 Filling Sunken Floors of Bathrooms/toilet with Cement Sand Mixure in the Ration 1:12 including all Charges of Compacting, Conveyances etc. Complete.

50.4.1.1 Providing and laying in position cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size) up to floor five level excluding the cost of centering, shuttering, finishing for leveling coarse of floor and roof etc.

OD88495/2025-2026 Providing, applying and finishing wall with exterior cement texture paint (Make suzuka Monocrete) of required shade. The surface must be flat, clean and smooth. Apply first coat strato primer on wall using roller and let dry for 30min. then apply second layer of strato primer and let dry for 30 min. Sand the entire surface with sand paper in circular motion to ensure the surface is smooth. Apply first coat using scraper ans spatula. dr for 30 min. Apply second coat. The rate including material, labour, conveyance and scafolding charges.

21.18 Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge ( Door handle, lock and stopper etc to be paid separately)

50.18.78 Making chases up to 12.5x12.5 cm in walls including making good and finishing with matching surface after housing pipe etc.

Finishing Works

13.50.1 Applying priming coat:With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)

13.48.2 Finishing with Deluxe Multi surface paint system for interiors and exteriors using primer as per manufacturers specifications:Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.75 ltr/10 sqm of approved brand and manufacture

13.69.1 Polishing on wood work with ready mixed wax polish of approved brand and manufacture:New work

13.80 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

13.43.1 Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

13.60.1 Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work

13.46.1 Finishing walls with Acrylic Smooth exterior paint of required shade:New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

13.44.1 Finishing walls with water proofing cement paint of required shade:New work (Two or more coats applied @ 3.84 kg/10 sqm)

13.45.1 Finishing walls with textured exterior pint of required shade:New work (Two or more coats applied @ 3.28 ltr/ 10 sqm ) over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm

11.52.1 Providing and laying machine cut, mirror polished Marble stone flooring, in required design (Simple geometrical, abstract etc.) and in patterns in combination with Italian marble stone of different colours, shades and finished surface texture etc., in linear portions of the building, all complete as per the shades and finished surface texture etc., in linear portions of the building, all complete as per the architectural drawings, with 18 mm thick stone slab laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm including pointing with white cement slurry admixed with pigment to match the marble shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-charge. a. 18 mm thick Italian Marble stone slab, Perlato, Rosso verona, Fire Red or Dark Emperadore etc.18 mm thick Italian Marble stone slab, Periato, Rosso verona, Emperadore etc.

8.3.2 Providing edge moulding to 18 mm thick marble stone counters, vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer -in-Charge.Granite work

11.41.2 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600 x 600 mm.

11.49.2 Providing and laying Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS : 15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).Size of Tiles 600x600 mm

11.48.2 Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg). including filling /grouting and finishing complete as per direction of Engineer-in-charge.Size of Tile 600x600 mm

OD88548/2025-2026 Providing and Fixing Cup board/Shelves with 17mm thick WPC(wood polymer composite) panel board conforming to ISO 9001-2015/ISO 14001-2015/ASTM D7295-14 standards and covered with 1mm mica at both sides & having 2mm edge band, fixing with screws and fittings etc, material foamed/ solid/textured/embossed WPC panel board, finish- laminate/UV coated/veneer, density-0.8-1.2 g/cm3, tensile strength -10-20MPa, water absorption - <5%, impact resistance-10-20 kJ/m2, flexural strength-20-30 MPa. etc complete.

50.9.12.1 Providing and fixing Thomson Multi wood board or equivalent make, in shelves with screws and fittings wherever required, edges to be painted with polyurethane primer (fittings to be paid separately) as per the direction of site Engineer-in-charge.

50.9.11.1 Providing and fixing Thomson Multi wood board or equivalent make paneling 12 mm thick, to frame, backing or studding with screws etc. complete ( Frames, backing or studding to be paid separately) as per the direction of site Engineer-in-charge.

9.70.1 Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete:125x64x1.90 mm

9.70.3 Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete:75x47x1.80 mm

9.70.4 Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete:50x37x1.50 mm

9.71.1 Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc. complete:125x64x2.50 mm

9.71.2 Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc. complete:100x60x2.50 mm

9.79.2 Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete.50 mm

9.79.4 Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete.75 mm

9.114.1 Providing and fixing magnetic catcher of approved quality in cupboard/ward robe shutters, including fixing with necessary screws etc. complete.Triple strip vertical type

9.114.2 Providing and fixing magnetic catcher of approved quality in cupboard/ward robe shutters, including fixing with necessary screws etc. complete.Double strip (horizontal type)

9.165.1 Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete.125 mm

9.165.2 Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete.100mm

9.165.3 Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete.75 mm

21.4.1 Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS: 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors including cost of cutting floors, embeding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer -in Charge.With stainless steel cover plate minimum 1.25 mm thickness

9.84 Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width form 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

11.41.4 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 1000x1000 mm

11.48.4 Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg). including filling /grouting and finishing complete as per direction of Engineer-in-charge.Size of Tile 1000x1000 mm

11.31 Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab.

12.45.1 Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with:12.5 mm thick tapered edge gypsum plain board conforming to IS : 2095-Part 1 :2011 (Board with BIS certification marks)

9.105.4 Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with Zinc coating of 120 gms/ (both side inclusive), consisting of floor and ceiling channel 50 mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete.66 mm overall thickness partition using 8 mm thick double skin multipurpose cement board reinforced with cellulose fibre manufactured through autoclaving process (High pressure steam cured) as per IS:14862 with suitable fibre cement screws

50.10.1 Steel work in built up G I tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

10.16.1 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes

13.52.1 Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work

OD89304/2025-2026 Providing and fixing Sandwich Polyurethane Foam (PUF) Panel roofing sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 30 mm thick(PUF panel sandwiched between precoated galvanized iron profile sheet 0.50mm thick top sheet and 0.35mm bottom sheet), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, strength -240 MPA-550MPA, coating mass- AZ 70- AZ 150, Overall density- 40-42 kg/m35-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. Details of cost for 216.14 sqm

8.8.1.2 Providing and fixing expansion hold fasteners on C.C./R.C.C./Brick masonry surface backing including drilling necessary holes and the cost of bolt etc complete. Wedge expansion typeFastener with threaded dia 10 mm

12.51.1 Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screwscomplete:Ridges plain (500-600 mm)

OD89321/2025-2026 Supply and Installation of Automatic Whirlybird Non Power Wind Roof Turbine Ventilator, Turbine Material- Stainless steel 304 grade, dia-600 mm, base- 6 core poly-carbonate sheet, No. of blade-36 Nos, type - wind driven, automatic grade- automatic, weight- not less than 5 kgs. etc complete

50.18.9.18.1 Providing and fixing PVC pipes including fixing the pipe with clamps/clips at 1.00 m spacing. This included jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 75 mm dia 6Kgf/cm2 External work- Exposed on wall

50.18.9.19.1 Providing and fixing PVC pipes including fixing the pipe with clamps/ clips/ at 1.00 m spacing . This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 110 mm dia 6 Kgf/cm2 - External work- Exposed on wall

50.18.9.21 Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75 mm dia Elbow

50.18.9.21.6 Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75x75x75 mm dia Door Tee

50.18.9.21.7 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75 mm dia Vent cowl

50.18.9.21.9 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75 mm dia Socket /coupling

50.18.9.22.1 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 mm dia Elbow

50.18.9.22.2 Providing and fixing PVC moulded fittings / accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 mm dia 45 degree Elbow

50.18.9.22.5 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes including jointing with PVC solvent cement 110x110x110 mm dia Tee

50.18.9.22.9 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement -110 mm dia offset

50.18.9.22.10 Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement -110 mm dia End Cap

50.18.9.22.11 Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes,including jointing with PVC solvent cement - 110 mm dia Socket/ coupling

50.18.9.22.12 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110x75 mm dia Reducer

12.50 Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

OD89624/2025-2026 Providing and fixing 200mm wide, 140mm deep 3 mm thick plain UPVC moulded channel type Rainwater gutter pipe of approved brand andmanufacturer (aquastar/euroguard/equivalent) with added ribs for extra strength, capacity-20L/m, iron brackets- 900x30x3 mm size @ 0.6/0.7m spacing, bolts, nuts and washers etc., including making necessary connections with rain water down fall pipes etc. complete

OD89625/2025-2026 supplying and fixing 160 mm dia PVC half gutter pipe with clamps at 1m spacing including the cost and conveyance of all materials to the site and all labour charges etc. complete 160 mm dia 4 kgf/cm2

10.29.2 Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete.Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both sides

10.25.2 Item Shifted to Sub head 14 as item 14.73 Item Shifted to head 14 as item 14.74 Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder,railings, brackets, gates and similar works

OD89642/2025-2026 Providing and fixing in position factory made PIR insulated sandwich wall/roof light weight solid core panels. The outer face on both sides of the panels will be pre-coated galvanized steel with 0.35 or 0.45 mm thick each. Panel shall be preferably fixed into 'C' channel made of 50mm size Stainless Steel screwed/fastened to the slab/column/beam etc. The panel shall fix verticallywith tongue and groove joint and horizontally locked with steel bar between each. Panels should be used as floor & roofing with additional structural support, steel or RCC depending upon the design. All the operation shall be completed in all respect as per drawings, Manufacturers specifications and under the overalldirection of Engineer-in Charge (Cost of all the material is included except "C channel" which will be paidseparately).Non load bearing panels 30mm thick of required size

7.33.1 Providing and fixing stone jali 40 mm thick throughout in cement mortar 1:3 (1 cement : 3 coarse sand), including pointing in white cement mortar 1:2 (1 White cement : 2 stone dust) with an admixture of pigment, matching the stone shade, jali slab without any chamfers etc.Red sand stone

OD152416/2025-2026 Providing and fixing matt finished terracotta clay jali in cement mortar 1:6 (1 cement : 6 coarse sand) used for facades & internal partitions etc., which gives circulation of natural light and fresh air, supporting frame with MS angle/flat, pointing the joints, closing the joints with white cement, rubbing and cleaning to smooth finish etc. As per standard specification.(supporting frame shall be paid additionally)

21.5 Providing and fixing powder coated aluminium work ( minimum thickness of powder coating 50 micron) consisting of tee /angle sections, of approved make conforming to IS : 733 in frames of false ceiling including aluminium angle cleats with necessary C.P brass/ stainless steel sunk screws, aluminium perimeter angles fixed to wall with stainless steel rawl plugs @ 450 mm centre to centre and fixing the frame work to G.I level adjusting hangers 6 mm dia. with necessary cadmium plated machine screws all complete as per approved architectural drawings and direction of the Engineer-in Charge ( level adjusting hangers, ceiling cleats and expansion hold fasteners to be paid for separately ).

OD89996/2025-2026 Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 3.25 mm thick aluminium composite panel material consisting of 2.25mm thick FR grade mineral core sandwiched between two Aluminium sheets (each0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.s The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performancecharacteristics all complete, as per theArchitectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places.

Plumbing & Sanitary works

OD90006/2025-2026 Supplying and fixing in position back coppered mirror (modi float /saint globain/equivalent) 6mm thick of appropriate sizes as per requirement and fixing with 6mm thick multiwood (approved brand as per standards)of the required size of the mirror fixed with silicon sealant etc . complete .The rate including all material cost ,labour charges , conveyance etc complete

OD90026/2025-2026 Supplying and fixing shower basket Jaguar/approved equivalent of model no. CAN 1177N including cost, mfixing charges etc complete

18.22.2 Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet:150 mm diameter

OD90042/2025-2026 Supplying and fixing angular stop cock with wall flange jaguar/approved equivalent including cost, fixing charges etc complete.

18.49.1 Providing and fixing C.P brass bib cock of approved quality conforming to IS: 8931.15 mm nominal bore

18.50.1 Providing and fixing C.P brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.15 mm nominal bore

18.51.1 Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.15 mm nominal bore

18.52.1 Providing and fixing C.P brass stop cock ( concealed) of standard design and of approved make conforming to IS: 893115 mm nominal bore

18.53.1 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS: 893115 mm nominal bore

18.54.1 Providing and fixing PTMT bib cock of approved quality and colour.15 mm nominal bore, 86 mm long, weighing not less than 88 gms

50.17.1.5 Supplying and fixing CP Health Faucet superior quality ( Jagur or equvalent make ) including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.

50.9.11.2 Providing and fixing Thomson Multi wood board or equivalent make paneling 18 mm thick, to frame, backing or studding with screws etc. complete (Frames, backing or studding to be paid separately)as per the direction of site Engineer-in-charge.

50.9.12.1 Providing and fixing Thomson Multi wood board or equivalent make, in shelves with screws and fittings wherever required, edges to be painted with polyurethane primer (fittings to be paid separately) as per the direction of site Engineer-in-charge.

9.114.1 Providing and fixing magnetic catcher of approved quality in cupboard/ward robe shutters, including fixing with necessary screws etc. complete.Triple strip vertical type

9.149 Providing and fixing casement handle made of zinc alloyed (white powder coated) for uPVC casement window with necessary screws etc. complete.

9.165.1 Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete.125 mm

9.165.3 Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete.75 mm

OD90372/2025-2026 Providing and fixing Single towel rail of Jaquar/ approved equivalent of 600 mm long stainless steel. The rate includes all material charge, labour charge, conveyance etc. complete

OD90373/2025-2026 Providing and fixing stainless steel tower bolts 250x10mm with necessary screws etc. complete

OD90381/2025-2026 Supplying and fixing in position Corner glass shelf (with bracket) of model No. ACN 1173 of Jaguar/approved equivalent including cutting & making good the walls ,cost and conveyance of all materials and labour charges for fixing etc. complete

OD90386/2025-2026 Providing & fixing of white colour ceramic Table top wash basin of size 565x420x140 mm of Jaguar/approved equivalent of (model No. KUS-WHT- 35935) Bottle trap (Jaquar Model No. ALD-769 L300x900) 32mm size with 300 mm and 190mm long wall connection pipe and wall flange and waste coupling of model no. ALD-705L130 . The rate includes cost and conveyance of all materials, all labour charges etc. complete

OD90389/2025-2026 Supplying and fixing Wall hung WC with UF soft close slim seat cover, hinges, accessories set of Jaguar/approved equivalent Model No: ARS-WHT-39951of size (360x570x360mm) or approved equivalent as required including all accessorie such as single piece slim concealed cistern with wall mounting frame, installation kit ans S type drain pip connection set for wall hung WC( without flush control plate) of model no. JCS-WHT-2400WS and control plate/knob Model No: JCP-CHR-852415 and all other necessary accessories of approved make approved make,as directed.The rate includes all material cost, labour charge, conveyance etc. complete. The rate includes fixing the consealed flush tank, fixing the rtack bolt of the EWC with proper concrete etc

OD90392/2025-2026 Providing and fixing Jaquar/equivalent Overhead Shower 150X150mm with shower arm 400x25x25mm square shape for wall mounted showers with flange. The rate includes all labour charge, material charge conveyance etc complete

OD90394/2025-2026 Providing and fixing single lever basin mixer without popup waste system with 450mm long braided hoses of model no. FLR 5025B Jaguar/approved equivalent. The rate includes all labour charge, fixing charge etc.complete.

OD90398/2025-2026 Providing and fixing SS-304 Grade Anti-Cockroach Floor trap of approved brand and standard size including all cost conveyance etc

OD90397/2025-2026 Supplying and fixing Exposed Part Kit of Concealed Stop Cock & Flush Cock with Fitting Sleeve, Operating Lever & Adjustable Wall Flange with Seal with Regular Body of Concealed Stop Cock Suitable For 20 mm Pipe Line with Protection Cap of jaguar/approved equivalent including cost, fixing charges etc complete.

OD90407/2025-2026 Providing and fixing stainless steel polished mat finish grating of approved quality and colour - Drain Size -125x125 mm and width 80 mm

18.8.2 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.20 mm nominal dia pipes

18.8.3 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.25 mm nominal dia pipes

18.8.4 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.32 mm nominal dia pipes

18.9.3 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer in-Charge. External work25 mm nominal dia pipes

18.9.4 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer in-Charge. External work32 mm nominal dia pipes

18.9.5 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer in-Charge. External work40 mm nominal dia pipes

18.9.6 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer in-Charge. External work50 mm nominal dia pipes

50.18.7.6.2 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing . This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 50 mm dia 6 Kgf/cm2 - Internal work- Exposed on wall

50.18.8.8.1 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 75 mm pipe 6 Kgf/cm2

50.18.9.13.2 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 25 mm dia 10 Kgf/cm2- External work - Exposed on wall

50.18.9.14.1 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 32 mm dia 10 Kgf/cm2 - External work- Exposed on wall

50.18.9.16.2 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 50 mm dia 6Kgf/cm2 - External work - Exposed on wall

50.18.9.17.1 Providing and fixing PVC pipes including fixing the pipe with clamps/ clip at 1.00 m spacing . This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 63 mm dia 6 Kgf/cm2 - External work - Exposed on wall

50.18.9.18.1 Providing and fixing PVC pipes including fixing the pipe with clamps/clips at 1.00 m spacing. This included jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 75 mm dia 6Kgf/cm2 External work- Exposed on wall

50.18.9.19.1 Providing and fixing PVC pipes including fixing the pipe with clamps/ clips/ at 1.00 m spacing . This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 110 mm dia 6 Kgf/cm2 - External work- Exposed on wall

50.18.9.21 Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75 mm dia Elbow

50.18.9.21.5 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement -75x75x75 mm dia Tee

50.18.9.21.7 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75 mm dia Vent cowl

50.18.9.21.9 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75 mm dia Socket /coupling

50.18.9.21.10 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement -75x63 mm dia Reducer

50.18.9.22.4 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement- 110 mm dia Bend

50.18.9.22.5 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes including jointing with PVC solvent cement 110x110x110 mm dia Tee

50.18.9.22.9 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement -110 mm dia offset

50.18.9.22.10 Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement -110 mm dia End Cap

50.18.9.22.11 Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes,including jointing with PVC solvent cement - 110 mm dia Socket/ coupling

50.18.9.22.12 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110x75 mm dia Reducer

50.18.8.9.1 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chased and making good the wall etc. 110 mm pipe 6kgf/cm2

50.18.9.8.2 Providing and fixing PVC pipes includings of pipes with one step PVC solvent cement, trenching and refilling & testing of joints complete as per direction of Engineer in Charge. 75 mm dia 4 Kgf/cm2

50.18.9.10.1 Providing and fixing PVC pipes includings jointing of pipes with one step pvc solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer in Charge. 150 mm dia 6 Kgf/cm2

18.17.2 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :32 mm nominal bore

18.17.3 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :40 mm nominal bore

18.17.4 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :50 mm nominal bore

18.19.3.2 Providing and fixing gun metal non-return valve of approved quality (screwed end): 40 mm nominal boreVertical

19.4.1.1 Providing and fixing square-mouth S.W. gully trap class SP -1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 100x100 mm size P typeWith common burnt clay F.P.S. (non modular) bricks of class designation 7.5

19.30.2.1 Constructing brick masonry chamber for underground C.I. inpection chamber and bends with bricks in cement mortar 1:4 ( 1 cement: 4 coarse sand) C.I.cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23kg and weight of frame 15 kg), R.C.C top slab with 1:2:4 mix (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) foundation concrete 1:5:10 (1 cement: 5 fine sand: 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement: 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design: Inside dimensions 500x700 mm and 45 cm deep for pipe line with one or two inlets:With common burnt clay F.P.S (non modular) bricks of class designation 7.5

19.31.2.1 Extra for depth beyond 45 cm of brick masonry chamber: For 500x700 mm sizeWith common burnt clay F.P.S.(non modular) bricks of class designation 7.5

OD90435/2025-2026 Providing & Fixing, testing and commissioning of Automatic Three phase water level controllers with level sensors for submersible pump shall have the following featuresa). Switch off the motor when the water level in tank reaches a preset level below the over flow pipe.b)Switch ON the motor if the water level in tank goes down below a preset value near.c)Switch off the motor in the event of dry running.d)Manual bypass mode.

2.6.1 Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.All kinds of soil

2.26.1 Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials.All kinds of soil

4.1.8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

5.1.2 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size derived from natural sources)

5.3 Reinforced cement concrete work in beams, suspended floors, roofs, having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with1:1.5:3 (1 cement : 1.5 coarse sand (Zone III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources).

5.9.1 Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.6 Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts

5.22.6 Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

5.22A.6 Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo - Mechanically Treated bars of grade Fe-500D or more

13.9.1 Cement plaster 1:3 ( 1 cement : 3 coarse sand) finished with a floating coat of neat cement.12 mm cement plaster

13.16.1 6 mm cement plaster of mix:1:3 ( 1 cement : 3 fine sand)

13.48.1 Finishing with Deluxe Multi surface paint system for interiors and exteriors using primer as per manufacturers specifications:Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of special primer applied @ 0.75 ltr /10 sqm

51.19.ST4 Supplying and installing ready made PVC Septic tank including the cost of carriage, trenching, placing at the level below ground level as specified as per the direction of engineer in charge (Provision for CC/RCC/Sand/06mm aggregate for the preparation of bed shall be paid separately) 4. 35 to 50 flush capacity

Site Development

16.91.2 Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge.80 mm thick C.C. paver block of M-30 grade with approved color design and pattern.

4.1.4 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 40 mm nominal size derived from natural sources)

4.1.8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

16.69 Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature jointed with cement mortar 1:3 ( 1 cement : 3 coarse sand) , including making joints with or without grooves ( thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge ( length of finished kerb edging shall be measured for payment ). ( Precast C.C. kerb stone shall be approved by Engineer-in-Charge)

OD164605/2025-2026 :[Derived from 16.68] Providing and laying 40 mm thick natural paving stone made by cutting sandstone/slate/granite/equivalent type of approved size, finished edges, design & shape, laid in required pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints by fixing artificial turf of pile ht 40/50mm etc. all complete as per the direction of Engineer-in charge.

Electrical

1.10.2 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLSPVC insulated copper conductor single core cable etc as required.Group B

1.10.1 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group A

1.21.2 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm

1.14.1 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2x1.5 sq.mm + 1x1.5 sq.mm earth wire

1.10.3 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group C

1.11 Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.

1.55.3 Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.Group C

1.14.2 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

1.14.3 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2 X 4 sq. mm + 1 X 4 sq. mm earth wire

1.18.2 Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor,unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.2 Pair

1.19 Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

1.21.1 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm

1.24.1 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 amps switch

1.24.4 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.3 pin 5/6 amp socket outlet

1.24.5 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.6 pin 15/16 amp socket outlet

1.24.6 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.Telephone socket outlet

1.24.7 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.TV antenna socket outlet

1.25 Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

1.26 Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

1.27.1 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.1 or 2 Module (75mmX75mm)

1.27.2 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.3 Module (100mmX75mm)

1.27.3 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.4 Module (125mmX75mm)

1.28.1 Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.1 or 2 Module

1.24.2 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.2 way 5/6 amps switch

1.24.3 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.15/16 amp switch

1.27.4 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.6 Module (200mmX75mm)

1.27.5 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.8 Module (125mmX125mm)

1.27.6 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.12 Module (200mmX150mm)

1.31 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings).

1.33 Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required.

1.34 Supplying and fixing brass batten/ angle holder including connection etc. as required.

1.35 Installation, testing and commissioning of wall bracket / ceiling fittings of all sizes and shapes containing up to two GLS/CFL/LED lamps per fitting, complete with all accessories including connection etc. as required.

1.41 Installation, testing and commissioning of pre - wired, fluorescent fitting/ compact fluorescent fitting of all types, complete with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq.mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

1.47 Supplying and fixing extra down rod of 10 cm length G.I. pipe, 15 mm dia, heavy gauge including painting etc. as required. (Note: More than 5 cm length shall be rounded to the nearest 10 cm and 5 cm or less shall be ignored)

1.53.1 Supplying and drawn of UTP 4 pair CAT 6 LAN cable in the existing surface/recessed steel/PVC conduit as required1 run of Cable

1.56 Supplying and fixing suitable size Gl box with modular plate and cover in front on surface or in recess, including providng and fixing 2 Nos. 3 pin 5/6 A modular socket outlets and 2 Nos. 5/6 A modular switches, connection etc. as required. (For light plugs to be used in non residential buildings).

90.4.1 Supply and installation of suitable size MS rod type fan clamp in the RCC slab as per IS 732 as required.

OD94566/2025-2026 Supply, conveyance, installation and commissioning of 5 star rating energy efficient BLDC ceiling fan of approved brand and manufacture (atomberg/Bajaj/Philips /equivalent), power source-corded electric, 1200mm sweep, speed-260rpm, operating voltage- 220V, Wattage-35watts, no of speed levels-6, air flow- min 235 cum/minute, operation control-remote/app/voice, no. of blades-3 nos, LED indicators, timer etc all complete.

OD94575/2025-2026 Supply 1200 mm sweep BEE star rated ceiling fan, Features- 230V, no. of blades 3, power consumption- min 50W, air flow capacity-above 210 Cmm, Blade type rust proof /dust proof Aluminium blades, Speed - min 350 RPM, Efficiency Energy Efficient, control type - button control, etc complete as required. (Brand : Crompton / Usha / Orient/ Havells/ Equivalent).

90.4.6 Conveyance, installation, testing and commissioning of wall mounting fans of all types using mounting brackets supplied along with the fan.

90.4.8 Charges for cutting holes suitable for accommodating exhaust fans up to 305mm sweep including plastering colour washing etc. as required.

90.4.10 Conveyance, installation , testing and commissioning of exhaust fans of size up to 450mm in the existing opening, fixing necessary anchor bolts / bolt and nuts etc., as required including giving connections with the supplied wire along with the exhaust fan.

90.10.1.2 Supply & Fixing the following types/ sizes of boxes suitable for modular accessories in surface/ recess including making good the damages, colour washing etc as required (RoHS compliant) 2 module moulded plastic box on surface

90.10.3.15 Supply and Fixing the following modular switches & accessories in the existing front plates and giving necessary connections as required (RoHS compliant )32A DP switch with indicator

90.10.3.33 Supply and Fixing the following modular switches & accessories in the existing front plates and giving necessary connections as required (RoHS compliant )25A 3pin Shuttered socket

90.11.1.11 Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required6 way (8+18) - three phase double cover (IP 42/43)

90.11.1.12 Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required8 way (8+24) - three phase double cover (IP 42/43)

90.11.1.14 Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required4 way (8+12) - double cover TPN vertical DB with provision for fixing 4P MCB / Isolator/ RCCB/ RCBO as incomer and SP/ TP MCB as outgoing (IP 42/43)

90.11.1.19 Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required6 way (8+12) - double cover TPN vertical DB with provision for fixing MCCB as incomer and SP/ TP MCB as outgoing (IP 42/43)

90.12.5.1 Supply & laying of one number PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in the existing RCC/ HUME / STONE WARE/ GI/ DWC pipe as required.2 core 4 sq mm

90.12.5.32 Supply & laying of one number PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in the existing RCC/ HUME / STONE WARE/ GI/ DWC pipe as required.3.5 core 120 sq mm

90.12.5.30 Supply & laying of one number PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in the existing RCC/ HUME / STONE WARE/ GI/ DWC pipe as required.3.5 core 70 sq mm

90.12.7.1 Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.2 core 4 sq mm with factory made clamp

90.12.7.30 Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.3.5 core 70 sq mm

90.12.7.40 Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.4 core 10 sq mm with factory made clamp

90.12.7.41 Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.4 core 16 sq mm with factory made clamp

90.12.7.42 Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.4 core 25 sq mm with factory made clamp

90.12.10.2 Supply & laying of DWC pipe in ordinary soil 0.75m below ground level including excavation50/38 mm or nearest size

90.12.10.4 Supply & laying of DWC pipe in ordinary soil 0.75m below ground level including excavation77/63 mm or nearest size

90.14.10.3 Supply, conveyance and fixing the following types & current rated control gears & switchgears conforming to IS 13947 suitable for 440 V, 50 Hz, AC supply in the existing panel assembly as required.16 A-100A, 16 kA (Ics=100%Icu), 4 pole, current limiting type MCCB having thermal setting range of 80 - 100% with thermal magnetic release having adjustable OL

90.16.1.3 Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required3.15 mm copper conductor ( 10 SWG)

90.16.1.5 Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required4.75 mm copper conductor (6 SWG)

90.16.1.6 Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required6.00 mm copper conductor (4 SWG)

90.16.5.3 Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required.3.15 mm (10 SWG)

90.16.5.5 Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required.4.75 mm (6 SWG)

90.16.5.6 Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required.6. mm ( 4 SWG)

2.10.1 Supplying and fixing 5A to 32 A rating, 240/415 volts, 10 kA, ""C"" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

2.10.4 Supplying and fixing 5A to 32 A rating, 240/415 volts, 10 kA, ""C"" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Triple pole

2.11 Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

2.13.1 Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

2.13.2 Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.63amps

2.15.2 Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 milli Amperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps

9.1.23 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 70 sq. mm (38mm)

9.1.32 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 10 sq. mm (25mm)

9.1.33 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 16 sq. mm (28mm)

9.1.34 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 25 sq. mm (28mm)

5.4 Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

5.8 Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

OD94624/2025-2026 Fabrication, Supply, installation, testing and commissioning of 100A LT panel board dust tight vermin proof floor/wall mounted cubicle construction with the following:- a)Incoming: 100A ISO - 1no.(Bus bar of air insulated Alu. size as per ISS).b) Outgoing-63A TPN MCCB-3 Nos, 40A TPN MCCB 2nos. Phase indication lamps, MFDM with PF/A/V in the incoming. Earth bus of adequate capacity and double earth connection to all switches, internal rigid connection etc., complete. The board shall be fabricated out of 16 SWG CR sheet and powder coated with shade RAL 7032 after phosphating. (Switchgears L&T, ABB, Schneider)

5.14 Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

OD94661/2025-2026 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. LAN socket outlet (RJ-45)

OD94662/2025-2026 Supplying and fixing following modular switch/ socket 15/16 amp switch with indicator of approved brand(Havells/GM/equivalent) on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

OD94702/2025-2026 Supply & installation of recessed 12 Watts LED round backlit down light with Aluminium housing with minimum output of 1200 lumens & 100 lumen/watt, , HEP diffuser, LED CRI>80, CCT 5700 (+/- 300K), L70 50,000 burning hours with valid LM 80, photo biological safety report & LM 79 report, driver with p.f > 0.9 and THD < 10% conforming to SELV standards with all accessories of approved brand and manufacturer(Philips/GM/Crompton/equivalent)

OD94703/2025-2026 Supply of Surface mounted 1 feet 5 Watts LED linear light with minimum output of 450 lumens conforming to SELV standards with all accessories as required. Wires/Cables shall be terminated properly as per the standards

OD94707/2025-2026 Supply of Surface mounted 4 feet 18Watts LED linear light with minimum output of 1800 lumens conforming to SELV standards with all accessories as required. Wires/Cables shall be terminated properly as per the standards

OD94708/2025-2026 Supply and installation of 9/10W B22 LED lamp with 90 lumen/watt in suitable holder with all other accessories etc. as required

OD94709/2025-2026 Supply of 300 mm sweep Wall fan working on 230V single phase A/C and other fixing accessories etc. complete as required4 X 2.5 sq. mm + 2 X 2.5 sq. mm earth wire

OD94710/2025-2026 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

OD94711/2025-2026 Supplying and fixing 40-63A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Triple pole

OD94712/2025-2026 Supply of 900 or more rpm, 300mm sweep 55 Watts exhaust fan, Body- PVC, suitable for single phase 230V, 50Hz, AC supply, air flow capacity- 1125 Cubic meters/Hr, power source- corded electric with bird guard and other fixing accessories etc. complete as required.

OD94713/2025-2026 Supply and fixing of 20mm dia flexible conduit in wall / suspended from ceiling as required.

OD94714/2025-2026 Supplying and laying 25mm casing & capping with all accessories as required.

OD94715/2025-2026 Preparation of as-fitted drawings, computing the actual connected load, submitting the work completion report, obtaining power allocation & power connection from KSEB. All statutory payments will be reimbursed on production of the original receipts. The rate shall include the charge for preparation of SLD, laminating and displaying it in designated area

OD94716/2025-2026 Preparation of all drawings submitting and getting approval from Electrical Inspectorate, submitting of Completion certificates and arranging inspection, getting sanction and energisation certificates from Electrical Inspectorate & commissioning the installation in the premises. The rate shall include the charge for preparation of SLD, laminating and displaying it in designated area. All statutory payments will be reimbursed on production of the original receipts.

OD94717/2025-2026 Supply and installation of DIN Rail Surge Protection Device (4+0) Class B & Class C/ Type 1 & Class 2 Tested as per IEC 61643 Part 11:2016 in suitable enclosure. Nominal voltage -230V 50/60Hz, MCOV of 275 V , Total Impulse current-50 KA (10/350 sec) & Total Max Discharge current 200KA (8/20 sec), Voltage protection level <1.5 kV & Residual Voltage @ 5 kA(8/20) <0.8 kV . The Surge Protection Devices should have TOV withstand for 120 Min : 438 V and with out Follow Current & Leakage Current. Protective Elements are High Energy MOV & GDT & the Protection Modes for : L & N to PE . Short- Circuit Current rating (Isccr) – 25 kA/50 Hz . Back up fuse required more than 160AgG/gL. Health Status Indication required in all cartridge. Total Response time <25 nano sec

OD94724/2025-2026 Supply, Installation, Testing and Commissioning of panel Meter Board made of 1.6mm GI sheet powder coated (min 50 microns)comprising following components, 100 TPN SFU, HRC fuse unit, 100A HRC fuse, neutral link, etc complete

OD94725/2025-2026 Supply, installation, testing and commissioning of 63A FP Automatic transfer switch with auto-manual operation and provision for DG start-stop command, utilisation category AC32, phase serperator for terminals, Supply/Load - On indication, pad lock for handle operation in suitable enclosure, interconnections etc complete

OD94726/2025-2026 Supply and fixing of outdoor decorative bollard luminaire of 800mm height, having efficacy not less than 70 lumen/watt and power consumption of not less than 8W, complete with integral type driver, closed diffuser and mounted using integral base plate in suitable foundation, complete with all accessories as required. Shall have IP 65 protection

OD94727/2025-2026 Supply of recessed 6 Watts LED round backlit down light with Aluminium housing with minimum output of 600 lumens & 100 lumen/watt, , HEP diffuser, LED CRI>80, CCT 5700 (+/- 300K), L70 50,000 burning hours with valid LM 80, photo biological safety report & LM 79 report, driver with p.f > 0.9 and THD < 15% conforming to SELV standards with all accessories as required.

OD94728/2025-2026 Supply of Surface mounted LED bulkhead having efficacy not less than 66 lumen/watt and power consumption of not less than 9W with high pressure die cast aluminium polycarbonate diffuser with all accessories as required. with IP 65 protection. (Wipro model - LW 07-141 or equivalent)

OD94730/2025-2026 Supply, Installation, Testing and Commissioning of 82.5 kVA Three Phase Diesel Genset of approved brand (Ashok Leyland(CPCB IV+ H4G4DE82) /Mahindra(mPower41015G)/Cummins(C82.5D5P)/Equivalent), Cooling systemwater cooled type, Engine- four stroke Turbo charged diesel engine, battery capacity- 90 Ah, engine rated -78/104(KW/HP), electric start D.G Set with acoustic enclosure and standard control panel with 125A 4P MCCB with stand by low earth fault relay using Neutral CT, additional battery charger, Voltage regulator, ammeter, voltmeter... indication lamp etc, Frequency- 50Hz, Insulation class- Class H or F, Protection- IP 23/IP 44 The engine shall be capable of taking 10% overload for one hour after 12 hours of continuous operation, Alternator brushless synchronous type, self regulated, SPDP enclosure, class F/H insulation, suitable for continuous operation at 1500 rpm, Voltage- 415 V +/- 5% at 0.8 p.f, 0.80 load factor, fuel tank capacity- not less than 145Ltr, weight- 1417 KG, Noise level-75db, range of Fuel Consumption-12-18Lr/hr (at 100% full load), rated output range-77.2-105 kW, speed-1500mm/m, wire system generally conforming to BS: 2613 & IS: 4722. The neutral of the DG set shall be provided with low set earth fault relay using adequate Neutral CT in the neutral earthing conductor. Both Engine and Alternator shall be mounted on common channel iron base frame, and with standard accessories such as anti-vibration pad, lead acid batteries (as specified by engine manufacturer) and engine driven battery charger along with leads, battery stand, fuel etc, Size -2850Lx1300Wx1510H (mm)/compatible etc complete.excl the cost of foundation.

90.6.5.4 Supply and drawing the following sizes of multi-core PVC insulated & FRLS PVC sheathed 650/1100 V grade copper conductor round flexible cables conforming to IS 694 part I 1960 in the existing surface / recess conduit as required including giving necessary connections of the following sizes.2 core 1.50 sq mm

90.6.5.18 Supply and drawing the following sizes of multi-core PVC insulated & FRLS PVC sheathed 650/1100 V grade copper conductor round flexible cables conforming to IS 694 part I 1960 in the existing surface / recess conduit as required including giving necessary connections of the following sizes.4 core 1.50 sq mm

90.12.1.30 Supply & laying of one number PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in ground including excavation of trench of size 35 x 75 cm, refilling the trench etc. as required but excluding sand cushioning and protective covering (in ordinary soil).3.5 core 70 sq mm

5.3 Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. (but without charcoal/ coke and salt ) as required.

OD94731/2025-2026 Supply, Installation, Testing and Commissioning of Network Video Recorder Providing & fixing Network Video Recorder 32-channel 720P or 24-channel 1080P high definition network video input and storage Support simultaneous HDMI and VGA output, resolution up to 1920×1080P/60Hz Supports 256Mbps bandwidth throughput handling, Supports 4-channel, 1080P video real-time decoding and synchronous playback.

OD94732/2025-2026 Supplying and drawing of UTP 4 pair CAT 6 LAN cable in the existing surface/recessed steel/PVC conduit as required1 run of Cable Make: Finolex/Dlink/equivalent.

OD94733/2025-2026 Supply, installation, testing and commissioning of indoor IR IP dome camera 2 MP 2.1mm/4mm/6mm focal length lens capable to 1.0 lux sensitivity, with IR n 480 TV lines.

OD94734/2025-2026 Supply, installation, testing and commissioning of indoor IR IP Bullet camera 2 MP 2.1mm/4mm/6mm focal length lens capable to 1.0 lux sensitivity, with IR n 480 TV

OD94740/2025-2026 Supply and installation of CAT6E 2 mtr long Patch cord factory crimped on both sides.

OD94741/2025-2026 Supply, installation, testing and commissioning of 32 inch QHD monitor(2560x1440) of approved brand- LG/Toshiba/Acer/equivalent, Aspect ratio- 16:9, Contrast ration-1000:1, refresh rate-180Hz and 5ms(GTG) response time, Display -LED, Display technology-IPS/VA/Equivalent, view angle-178 degree, image brightness-300 or more, speakers- built-in speakers, finish-matte/glossy, Additional features-HDMI/VGA ports

OD94742/2025-2026 Supply, Installation, testing and Commissioning of Surveillance Hard disk 6TB of approved brand- Seagate/western digital/equivalent, Capacity- 6TB, Hard disk interface-Serial ATA-600/equivalent, Network technology- SATA/equivalent, Product features-portable, rotational speed-5400 RPM, data transfer rate-5 Gigabytes per second, read speed- 180 megabytes per second, media speed-180 MB/s, cache memory installed size- 256, form factor- 3.5 inch.

OD94743/2025-2026 Supply, Installation, testing and commissioning of Cat6 24 Port fullyloaded Patch Panel.

OD94744/2025-2026 Supply, installation, testing and commissioning of HDMI Cable of approved brand and manufacturer.

OD94745/2025-2026 Supply, installation, testing and commissioning of wall mounted powder coated(50 microns) rack for CCTV, Size15Ux500Wx500D With Front Glass Door With Lock & Key, Side Openable Panels with Lock & Key, 6Way 5A PDU,1U Cable Manager, Cooling Fan, H/W Kit10. thickness of sheet to be used-2.00mm or more, compartments & connections. etc. complete.

OD94746/2025-2026 Supply and fixing RJ45 jack with cover , including crimping/Punching of UTP 4 Pair CAT 6E LAN Cables on both ends with RJ45 Connector.

OD94747/2025-2026 Supply, installation, testing and commissioning of 16 Port 10/100/1000 Mbps PoE Switch.

OD94748/2025-2026 Supply, fixing, testing and commissioning of the WIFI, Access point with 450Mbps on 2.4GHz bandwidth & 867Mbps on 5GHz bandwidth,total of 1317Mbps speed compatable with 802.3af and passive PoE. Centralized Software Controller Monitor and manage hundreds of EAPs in a single or multiple sites.Free cloud access to manage from anywhere, anytime.Configure and automatically synchronize unified wireless settings to all EAPs in the network.Secure Guest Network with Facebook Wi-Fi and SMS Authentication

OD94749/2025-2026 Supply, Installation, testing and Commissioning of 8 PORT POE SWITCH of approved brand - TP -Link/CP PLUS/HANUTECH/Equivalent, No. of ports-10, compatible device- camera, Switch type- Ethernet/equivalent, Voltage- 53.5 Volts(DC), upper temp- 40Degree C, Data transfer rate- 20Gigabits per Sec or more, Weight - 1.23 kg or more.

OD94750/2025-2026 Supply, Installation, Testing and Commissioning of 8 PORT GIGABIT Unmanaged SWITCH of approved brand and manufacturer-Hikvision, no of ports-8, compatible device- Desktop, switch type- unmanaged, voltage-48Volts(DC), interface-RJ45, data transfer rate- 20Gigabits per second, current rating -2.5 Amps, Dimension-30Lx30Wx5H cm/variable..

OD94751/2025-2026 Supplying and fixing following modular socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. Telephone socket outlet of approved brand.

OD94752/2025-2026 Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 2 Pair

OD94753/2025-2026 Supply, installation, testing and commissioning of Telephone distribution box- 50 pair box with lock and Krone modules- approved brand and manufacturer(generic/equivalent), material- powder coated metal.

OD94754/2025-2026 Supply, Installation, Testing & commissioning of Telephone with speaker and caller -id of approved makes - Panasonic/beetal/equivalent, type - corded, mount- desk & wall mountable, including all other accessories for connection.

OD94755/2025-2026 Supply, fixing, testing and commissioning of the Intercom of approved brand and manufacturer- Syntel/Navkar systems/equivalent. with Digital EPABX with PSU, CPU & LINE CARDS, features- 4 co- line + 1 digital Ext +64 extensions (expandable 64 lines 4 trunk), 10000 calls memory, built in 75 internal voice prompts for users help, cable type- ethernet, connector- RJ45, ethernet cable category- cat 6, no of pins-5 or more, model- NEOS 4S/equivalent.

Air Condition

OD94756/2025-2026 SITC of wall mounting type 5 kVA Smart Voltage Stabilizer designed for Air conditioning(upto 2 ton AC) load working on 240V, 50Hz Single Phase AC supply to feed output voltage at +/- 10% tolerance with automatic low voltage & high voltage cutoff, built in thermal overload protection, powder coated enclosure. Additional features- digital display, toroidal transformer for stable out, reduced heat & low noise operation etc. complete.

OD94757/2025-2026 Supply of 2 TR capacity 5 star Split inverter AC of approved brand (Bluestar/Carrier/Samsung/ equivalent), star rating- 5 Star BEE rating, cooling capacity above 6000 W, Power -AC 135-280V, Frequency - 50Hz, display - LED, Compressor- variable type, refrigerant- R-32, Condensing type- full copper (Condenser & evaporator coils), Operating modes-auto mode/dehumidification/cool mode/turbo mode/sleep mode, Auto re-start type, area coverage -150-200 sqft, air circulation- 700 CFM, Components- wall mounted Air Conditioner unit with Indoor & Out door Split type units with cordless remote, copper wire etc.

OD94758/2025-2026 SITC of supporting stand / clamp for fixing the outdoor AC unit using suitable support bars /anchor bolts and safety hook up etc. including all accessories etc. material- powder coated MS angle/flat. etc. complete.

OD94759/2025-2026 SITC of Additional flexible PVC control cable of 4C X 2.5 sq mm of approved brand & manufacturer- Sturlite/Anchor/V- guard/equivalent to connect between indoor and outdoor AC units.

OD94760/2025-2026 SITC of Additional flexible PVC power cable of 3C X 2.5 sq mm of approved brand & manufacturer- Sturlite/Anchor/V- guard/equivalent to connect between indoor and outdoor AC units.

OD94761/2025-2026 SITC of Additional 20mm PVC drain piping of good quality to extend water drain connection till nearest silt terminal as required at site. material- flexible heavy-duty extension, tube- multipurpose water in-outlet hose pipe for commercial use (AC units).

OD94762/2025-2026 SITC of additional refrigerant lines (Both suction & discharge) using soft drawn copper pipe of the suitable sizes recommended by the manufacturer for AC units including nitrile rubber thermal insulation of good quality to extend the refrigerant gas connection till outdoor unit as required at site.

OD94763/2025-2026 Installation, Testing & Commissioning of 5 star inverter type AC units with necessary including fixing of Indoor & outdoor units, necessary gas charging as per manufacturer standards, giving power connection to nearest Power plug point / MCS with 16A plug top, connecting indoor and outdoor units using soft copper refrigerant pipes insulated with nitrile rubber or equivalent material , PVC insulated flexible cable as per original manufacturers standards, drain water provision.

OD94764/2025-2026 SIGN BOARD Providing and installing in position the following type of sign boards made out of 3mm thick rigid PVC board with computer cut with texts written to recommended height in photolumiscent material complete vide technical specifications with mirror fasteners. Sizes and mounting height of the board shall be as per technical specification. No Smoking sign board 12'' x 4''.

OD94765/2025-2026 Providing and installing in position the following type of sign boards made out of 3mm thick rigid PVC board with computer cut with texts written to recommended height in photolumiscent material complete vide technical specifications with mirror fasteners. Sizes and mounting height of the board shall be as per technical specification. Fire Exit sign board 12'' x 4'' with arrow markings.

OD94766/2025-2026 Supply, installation of in position the signages of "Fire boards approved by Kerala state fire service made out of PVC rigid sheet 3mm thick with computer cut PVC non-reflective self-adhesive imported vinyl painted on the front of PVC rigid sheet complete with wall mounting arrangements with mirror screws" with lettering "ASSEMBLY AREA" Size & design- as per approved standards and specifications.

OD94767/2025-2026 Supply and providing 6 kg ABC DRY POWDER type fire extinguisher of approved brand and manufacture (Lifeguard/ Eco fire/Safeverse/Equivalent) with Wall hook, Discharge pipe, how to use sticker, expiry date certificate, hose and clamps including fixing it to wall as required.

OD94769/2025-2026 Supply and providing 9Litre water type fire extinguisher of approved brand and manufacture (Lifeguard/ Eco fire/Pyro guard/Equivalent), Operating temperature- -30 to +60 Celsius, minimum effective discharge-95%, fire rating- 3A, with Wall hook, Discharge pipe, how to use sticker, expiry date certificate, hose and clamps including fixing it to wall as required.

OD94770/2025-2026 Supplying, Installing, Testing & Commissioning of 2 way Fire brigade Inlet connection fabricated from 100 mm dia MS Class B medium grade pipe comprising of two 63 mm dia gun metal male threaded non return valve

OD94771/2025-2026 Supplying, Installing, Testing & Commissioning of Air release valve gun metal body as per IS:778. 20 mm dia ..

OD94772/2025-2026 Supplying, Installing, Testing & Commissioning of Hose Box (Fire Hose cabinet) to accommodate one piece of 63 mm dia fire hose along with one piece of 63 mm dia male & female couplings and one branch pipe. The cabinet is made of M.S. powder coated with glass fronted hinged doors and lock.

OD94773/2025-2026 Supplying, Installing, Testing & Commissioning of Hose reel drum made of Mild Steel, with mounting brackets 19 mm dia nylon braded smooth surface rubber thermo plast hose 30 mtrs length with shut off nozzle.

OD94774/2025-2026 Supplying, Installing, Testing & Commissioning of Fire Fighting Hose , all synthetic fiber circular woven jacketed ,control percolated delivery hose, 38kg/cm2 burst pressure,

OD94775/2025-2026 Supplying, Installing, Testing & Commissioning of branch pipe made out of SS 63 mm short male instant. Inlet male threaded outlet, fitting with 15 mm bore nozzle ISI certified.

OD94776/2025-2026 Supplying, Installing, Testing & Commissioning of Hydrant valve 63 mm dia oblique type with SS body & working parts, with instantaneous hose coupling adaptor and PVC blank cap & chain. ISI certified.

OD94777/2025-2026 Supplying, Installing, Testing & Commissioning of Ball Valve as per IS 5312. 20 mm dia

OD94778/2025-2026 Supplying, Installing, Testing & Commissioning of Non Return Supplying, Installing, Testing & Commissioning of Non-Return Valve single plate wafer type slim seal check valve, short pattern type with integral hinge pin disc, nitrile rubber O - ring seat and face sealing as per IS: 5312 and ISO certified.

OD94779/2025-2026 Supplying, Installing, Testing & Commissioning of charges for High Pressure switch arrangement for pump room and total system (model- Danfoss Kp 36/equivalent.), operation- automatic, contact type- normally open, circuit type- 1 way, control- push button, switch type- pressure switch.

OD94780/2025-2026 Supplying, Installing, Testing & Commissioning of charges of Pressure gauge arrangement for pump room and total system (Dia 100mm/nearest available size), material -composite of aluminium, brass, glass, body- metal.

OD94781/2025-2026 Supplying, Installing, Testing & Commissioning of automatic fire hydrant system panel for Terrace pump of approved brand and manufacturer ISI/ISO certified.

OD94782/2025-2026 Supplying and installing of in position the following type of sign boards made out of 3mm thick "Opaque" PVC foam board with computer cut, PVC Non-reflective self-adhesive vinyl painted foam board, complete with mirror fasteners.

OD94783/2025-2026 Supplying and installing of in position the following type of sign boards made out of 3mm thick "Opaque" PVC foam board with computer cut, PVC Non-reflective self-adhesive vinyl painted foam board, complete with mirror fasteners. EVACUATION PLAN as per standard specification.

OD94784/2025-2026 STATUTORY APPROVAL Complete services from the contractor for Laisoning works such as filing necessary applications, submission of forms for approval to local fire authorities, depositing the fees / other amounts as required for getting the premises / installations, inspected and approved and all other formalities required till approved by Local Fire Authorities. All the expenses incurred in this regard shall be borne by the Contractor. The official payments to be made for any security deposit etc. in this regard which shall be reimbursed on production of original voucher.

OD94785/2025-2026 Supplying, Installing, Testing & Commissioning of electrically operated Terrace Pump of 450LPM capacity 24 MWC, high efficiency volute type with cast iron casing, cast iron impeller, pump coupled with a squirrel cage induction motor TEFC type with a supply condition of 415 V 50 Hz foot mounted type for Suitable 5HP at 1350 RPM 3 kg including base plate coupling guard and all other necessary accessories.

OD94786/2025-2026 Supplying, Installing, Testing & Commissioning of butterfly valve wafer type Stainless steel/SG iron disc , lever operated as per IS:13095 in PN 1.0 , teflon or nylon bushing, nitrile O rings in standard mounting flanges with hand lever type. 110mm dia

OD94787/2025-2026 Under Ground Piping- Supplying, Installing, Testing & Commissioning of underground piping M S pipe Class 'B' medium grade ISI mark complete with all necessary fittings such as nuts & bolts, bends, flanges, tees etc . and piping shall have anti corrosive wrapping treatment. 100 mm dia.

OD94788/2025-2026 Above Ground Piping-Supplying, Installing, Testing & Commissioning of MS 'B' class medium pipe as per is medium grade of following dia, with necessary fittings such as nuts & bolts, bends, flanges ,etc and Welded joints, The pipe shall be painted with two coats red colour enamel paint over primary coat of Primer. 80 mm dia

OD94789/2025-2026 Above Ground Piping- Supplying, Installing, Testing & Commissioning of MS 'B' class medium pipe as per is medium grade of following dia, with necessary fittings such as nuts & bolts, bends, flanges, etc and Welded joints, The pipe shall be painted with two coats red colour enamel paint over primary coat of Primer. 100 mm dia

OD94790/2025-2026 Supplying, Installing, Testing & Commissioning of butterfly valve wafer type Stainless steel/SG iron disc , lever operated as per IS:13095 in PN 1.0 , teflon or nylon bushing, nitrile O rings in standard mounting flanges with hand lever type. BUTTERFLY VALVE - 80 mm

OD94791/2025-2026 SIGN BOARD Providing and installing in position the following type of sign boards made out of 3mm thick rigid PVC board with computer cut with texts written to recommended height in photolumiscent material complete vide technical specifications with mirror fasteners. Sizes and mounting height of the board shall be as per technical specification. Fire Duct sign board 12'' x 4''.

Elevator

Furniture

OD96342/2025-2026 Supplying and Providing Executive Table using 16mm Marine Plywood conforming to ISO-9001-2015/ISO 14001-2015/BS 1088-2003 and 1 mm Mica finish, 2mm PVC Edge band, in the right hand side using hinged doors ; top with a sliding drawer, keyboard drawer; Stainless steel soft close telescopic channel & soft close hinges of approved brand ( EBCO or equivalent) ; 100 mm size SS handles ; locking facility ( ISI),provision for CPU/UPS etc. as per approved drawing details including cost and conveyance of all materials and labor charges for making , fixing the table etc complete.- Minimum height of table to be supplied-75cm - (Measurement to be made for top surface area)

OD96343/2025-2026 Supply and providing Executive High back revolving chair- Head rest height and angle adjustable. Seat Height adjustment Back rest angle Adjustable. Armrests 3d multi-function. Back upholstered with nylon mesh. Seat upholstered with nylon mesh. Multi -function 3 class locking mechanism. Powder coated/Electro plated TUV-CLASS 4 Gas spring 120mm, Aluminum base with PU castors:330mm Tested as per BIFMA X5.1 standards including cost and conveyance of all materials and labor charges for making.

OD96345/2025-2026 Supplying and providing Sofa Set ( 3 + 2 ) seater as per the approved design; where as 3 seater of size 180 x 90 x 50 cm and 2 seater of size 120 x 90 x 50 cm Seat & backrest upholstered with leatherette 14 Gauge pipe 1.25 thickness Powder coated/ electro plated chrome mild steel cantilever base. Tested as per BIFMA X5.1 standards including cost and conveyance of all materials and labor charges for making etc. complete.

OD96346/2025-2026 Supply and providing Teapoy Using Marine plywood 16mm with ISO/ISI-9001-2015 and 1 mm Mica finish, 2mm PVC Edge band, size of - 90Lx45Wx60H cm including cost and conveyance of all materials and labor charges for making.

OD96347/2025-2026 Providing and Fixing Cup board/Shelves with 17mm thick WPC(wood polymer composite) panel board conforming to ISO 9001-2015/ISO 14001-2015/ASTM D7295-14 standards and covered with 1mm mica at both sides & having 2mm edge band, fixing with screws and fittings etc, material foamed/ solid/textured/embossed WPC panel board, finish- laminate/UV coated/veneer, density-0.8-1.2 g/cm3, tensile strength -10-20MPa, water absorption - <5%, impact resistance-10-20 kJ/m2, flexural strength-20-30 MPa. etc complete.

OD96348/2025-2026 Wall paneling with 10mm thick WPC(wood polymer composite) panel board and framing with 16mm thick marine ply board covered with 1mm mica at both sides & having 2mm edge band, WPC panel board should conforming to ISO 9001-2015/ISO 14001-2015/ASTM D7295-14 standards, materialfoamed/ solid/textured/embossed WPC panel board, finish- laminate/UV coated/veneer, density-0.8-1.2 g/cm3, tensile strength -10-20MPa, water absorption - <5%, impact resistance-10-20 kJ/m2, flexural strength-20-30 MPa. etc complete.

OD96377/2025-2026 Supply and providing Two seater Sofa cushioned - Seat & backrest upholstered with leatherette 14 Gauge pipe 1.25 thickness Powder coated/ electro plated chrome mild steel cantilever base. Tested as per BIFMA X5.1 standards including cost and conveyance of all materials and labor charges for making.

OD96379/2025-2026 Supply and Providing Single Cot hardwood bed with plank top, material- Teak/oak/maple/other durable hardwood material conforming to ISO 9001-2015/approved quality in make, Frame- solid hardwood frame with mortise and tenon joints, Slats- hardwood slats for support and ventilation, Headboard- as per requirement, Hard wood single cot with plank top - 190*90*45 cm.

OD96380/2025-2026 Supply and Providing Single bed mattress with pillow of approved brand and manufacturer(Nilkamal/Dunlop/Repose /equivalent), Product dimension-183 L x 91W x 13Th (cm), Item weight not less than 7 kgs, Upholstery material- Polyurethane, Fill material- High density Foam, other features- three layer mattress with PU foam layer and knitted fabric cover. etc. complete.

OD96381/2025-2026 Providing Beside Cupboard:- Material- Particle board/solid wood conforming to ISO 9001-2015/BS 1088 /ASTM D 3023/Approved quality ensured with 1 mm mica top finish, Finish- laminated finish, drawers-2-, size -45*45*45 cm.

OD96382/2025-2026 Supply and Providing storage cupboard Using Marine plywood 16mm Marine Plywood conforming to ISO-9001-2015/ISO 14001-2015/BS 1088-2003 standards and 1 mm Mica finish, 2mm PVC Edge band all complete as per the direction of engineer in charge and as per the drawing produced.

OD96383/2025-2026 Supply and Providing Single Cot Bed, material: Hard wood(Sheesham wood-rose wood), conforming to ISO 9001:2015/IS 1708/ASTM D1166/Other approved equivalent certification, Finish- Polished, Max weight- 150Kgs, with plank top - 200*100*76 cm. etc complete

OD96384/2025-2026 Supply and Providing Single Cot mattress 190x92x15cm/ compatible of approve brand and manufacturer (Dunlop/Sleepwell/repose/equivalent) with set of pillows, support layer: pocket spring, comfort layer: memory foam, upholstery material- polycotton/knitted, comfort level- Medium firm, support layer- High Density Foam, Other features- Orthopedic mattress. etc complete

OD96385/2025-2026 Supply and Installation of LPG Hose tube up to 1.5m long.

OD96386/2025-2026 Supply and Installation of LPG Copper pipe with brass connector on both sides, Length up to 1 meter and 3/8 inch thread of approved brands.

OD96387/2025-2026 Supply and Installation of 5/8 inch Brass LPG Ball Valve of approved brands.

OD96388/2025-2026 Supply and Installation of GAS Pipe Line made up of MS threaded C Class pipe, TATA or Jindal Make including enamel painting of two or more coats as per engineers instructions

OD96389/2025-2026 Supplying and Fixing Powder coated aluminium fresh air grill, powder coating -min 50 microns, thickness of louvers 1.5 to 3 mm, air flow rate-upto 1000 CFM, velocity- upto 500 fpm, mounting type - clip/screws, weatherproof coated grill to prevent weather & corrosion. etc complete.

OD96390/2025-2026 Fabrication, Installation, Testing and Commissioning of GI ducting for kitchen exhaust hood with grease/carbon/electrostatic filter units, Sheet thickness - 26 G/22 G GI sheet, material- Galvanized iron sheet of ISI approved brand (JSW/tata/equivalent) and conforming to ISO 9001-2015, GST coating -120 GSM, Other feature- Highly durable- non corrosive, proper sealed with sealants(leak proof), air tight, connection b/w duct sheets by flange connections

OD96391/2025-2026 Fabrication, Installation, Testing and Commissioning of GI ducting for Fresh air with pre-filter/activated carbon/electrostatic/filter units, Sheet thickness - 26 G/22 G GI sheet, material- Galvanized iron sheet of ISI approved brand (JSW/tata/equivalent) and conforming to ISO 9001-2015, GST coating -120 GSM, Other feature- Highly durable- non corrosive, proper sealed with sealants(leak proof), air tight, connection b/w duct sheets by flange connections. etc complete.

OD96392/2025-2026 Supply and Providing SS 304 graded Dosa burner range, size 1200x750x850+100 mm, 20mm dosa plate, no. of knob- 2nos, leg-2 nos.

OD96393/2025-2026 Supply and Providing Stainless steel utility sink free standing single sink unit with back flash, Body - SS 304 grade, bowl- single bowl with under shelf, size- 110x60x80+10 cm, sink bowl size- 39x33x22 cm, weight- approx 23-28 kgs, other features- heavy duty, multipurpose, heavy load capacity, polished surface finish. etc complete.

OD96394/2025-2026 Supply and Providing Stainless Steel work table, Body- SS 304, Size range- 150x60x80cm, shelves- 2(excl top), weight - approx 22-28kgs, support leg-4/6 nos, sturdy frame for supporting heavy loads, uses- cutting, chopping, mixing and assembling dishes, suitable for commercial kitchens, labs, workshops, etc complete.

OD96395/2025-2026 Supply and Providing Two Burner Indian Cooking range, Body - SS 304, Burner material- cast iron, no. of burner-2 with pan support, shape- rectangular, burner specification- high pressure burner - approx-110x60x80+10 cm, weight approx -35-40 kgs, no. of knob- 4, gas type - LPG, support- 4 nos of legs, storage rack and back flash. etc complete.

OD96396/2025-2026 Supply and Providing Single Burner Indian Cooking range, Body - SS 304, Burner material- cast iron, no. of burner-1, shape- square, burner specification- high pressure burner in pan support- approx-60x60x45cm, weight approx -15-20kgs, no. of knob- 2, gas type - LPG, support- 4 nos of legs, storage rack and back flash. etc complete.

OD96397/2025-2026 Supply and Providing 3 Burner Indian Cooking range, Size- 165x60x80+10, Burner specifications- 3 Nos of high pressure high efficiency burners, 6/4 LEG GRID, Body material- SS 304, Burner material- cast iron, 1 under shelf, Back side splash, weight - approx 45 kgs, power source- gas, No. of Knob- 6, etc complete.

OD96399/2025-2026 Supply and Providing Stainless Steel 3 Tier Pot Rack, Size 150x60x150 cm, Body- SS 202 grade support - legs of 1.5'' with adjustable nylon boots.

OD96400/2025-2026 Supplying and Providing Stainless Steel 2 Tier Trolley with 10 cm deep tray, 4 side 15cm splash, Shelf- 2 tiered shelf, 4 swivel Castors wheel with brake, material- frame & body- SS 304 grade, load capacity-20-30Kgs, Size - 90x60x85+15 (cm). etc Complete

OD96401/2025-2026 Supply and Providing 6 pot Stainless Steel Bain Marie, Body - SS 304 grade, power - 3 kW, Weight approx - 20-25 Kgs, Voltage- 230V, Frequency -50Hz, Phase- Single phase, No. of pots- 6,Pot capacity- Approx. 6-8 L, size of GN pan-9.5 inch dia, 8 inch depth, support -4/6 legs, shelf-1 under shelf and provision for electrical connection with thermostat. etc complete.

OD96402/2025-2026 Supply and Providing 3 Star rated Refrigerator with digital inverter, compressor- Digital Inverter compressor, Power-AC 220-240 V, Power Consumption-240-260 W, Frequency -50 Hz, cooling refrigerant- R-600/Equivalent, capacity -above 300 L, type- De frosting type, top mount, air flow- twin cooling plus/equivalent, double door, conforming to BEE rating, energy efficient and saver with cool pad, including toughened glass shelves, stabilizer- inbuilt type, weight not less than 50Kgs, Size range- 60L x 67Wx 1630H (cm)/compatible etc. complete

OD96403/2025-2026 SITC of 18 '' Single phase axial fan sunction, material- metal, wattage- 135 watts, no. of blades-4/5, speed- 1350 RPM, voltage-220V, power source- corded electic, control- button/remote, mounting type- wall/ceiling, item weight not less than 0.9 Kgs. etc complete

OD96404/2025-2026 Supply and Providing Electric Hot Plate:- 120x75x85+10cm With 120x 68 x 2 cm SS 202 grade plate, Wattage- 3000 Watts, voltage-220 Volts, Knob-4, non - stick coated, 7 temperature control, Oil drainage, fire window Etc. Bottom cross support

OD96405/2025-2026 Supply, Installation, Testing and Commissioning of Stainless Steel Kitchen Exhaust Hood with Filter, Body material-SS 304 grade 18/19G, capacity- 1200m3/h, suction capacity-600 CFM, size-600mm x500mm, style- wall type, Product type- exhaust hood with detachable oil collection tray and baffle filter. etc all complete(length of hood as per site requirement- actual quantity will be measured in metres).

OD96406/2025-2026 Supply and Fixing 1 HP Heavy Duty 24 inch Axial Flow fan for exhaust system, power -1HP, 3 phase, body material-mildsteel/cast iron, blade material- aluminium alloy, voltage-415 Volts, blow type- axial, air flow capacity-5000 m3, electric current type-AC, Fan speed -RPM, No. of blades-4/6, mounting type -duct, shapedrum shape, CFM- above 6000. etc all complete

OD96408/2025-2026 Supply and providing Standard Solid Wooden round dining table 4 seater with standard chairs set, wood type- Second class teak/sheesham/mahagony/equivalent, finish- walnut/teak/mahagony, item weight - not less than 38 kgs, dimension-102x102x76 cm/equivalent

OD96409/2025-2026 Supply and Fixing Premium Quality 100% Blackout Roller Blinds, Material- Polyester coated material-100% blackout fabric, Opacity- Blackout Inches, Pattern - Solid/equivalent, mounting type- Inside wall mount, operation mode - manual, Control Type - Cord control, aluminium brackets & railings, Features- High Quality/ durable/UV protection/water proof, Application for Office room, drawing room,etc complete.

OD96410/2025-2026 Supply and Fixing Premium Quality Zebra Roller Blinds, Material- Polyester Blend/Polyster material @ 280GSM, Opacity- Light Filtering Inches/sheer, Pattern - Solid/equivalent, mounting type-Inside wall mount, operation mode - manual, Control Type - Cord control, aluminium brackets. & railings, Features- High Quality/ durable/UV protection/stain resistant/Light Filtering, Application for Office room, drawing room,etc complete.

OD96419/2025-2026 Supplying and Providing Beside Cupboard:- Material= Moisture resistant/termite proof Marine Plywood conforming to ISO 9001-2015/BS 1088 /ASTM D 3023/Approved quality ensured with 1 mm mica top finish, Finish- natural wood finish/laminated finish, drawers-2-3, size -45*45*55 cm.

OD96422/2025-2026 Supply and Providing King type mattress 75"x72"x8"/ compatible of approved brand and manufacturer (Dunlop/Sleepwell/repose/equivalent) with set of pillows and microfibre reversible AC comforter blanket of soft quilted 200-300GSM, upholstery material- Breathable Premium Fabric/Cotton/knitted, comfort level- medium soft, support layer- High Density Foam/latex foam/memory. foam etc. complete.

OD96423/2025-2026 Supply and Providing King Size Bed with storage box, Bed material- Solid wood/hardwood(sheesham/equivalent), finish- polish/honey/teak/equivalent, Size- 200x190x107cm/compatible, weight not less than 90kgs, maximum weight recommendation-150-200 kgs, with decorative headboard (with/without headboard storage) etc all complete

Sign Board

OD96436/2025-2026 Supply and fixing signage for rooms and internal directions. The signage letters will be made with premium quality vinyl sheet of approved colour, pasted on 3mm thick aluminium composite panel backing. The signage will be either fixed on the wall with the screws & double tape or hanged from the false ceiling with the help of hooks & chains complete work.

OD96437/2025-2026 Supply and fixing symbol signage such as No. Smoking, No Spitting, Drinking Water etc. signage of standard sizes as per conventional design/ colour code on 3 mm thick aluminium composite panel. The signage will be either fixed on the wall with the help of screws and double tape or hanged from the false ceiling with the help of chain and screws etc. complete work.

OD96438/2025-2026 Providing and installing in position the following type of sign boards made out of 1.5 mm thick 304 grade stainless steel with computer cut with texts written to recommended height in photolumiscent material complete vide technical specifications with mirror fasteners. Sizes, Letter height, Colour, Back ground, language and mounting height of the board shall be fixed at all height/ as per drawing.

OD96439/2025-2026 Providing and installing in position the following type of sign boards made out of 4mm thick ACP sheet with computer cut with texts written to recommended height in photolumiscent material complete vide technical specifications with mirror fasteners. Sizes, Letter height, Colour, Back ground, language and mounting height of the board shall be fixed at all height/ as per drawing as per design mounted on 2.5cm x 2.5cm size square MS pipe frame