Provision of Additional Multi Storied Building for Training Centre of CEPTAM at Metcalfe House, Delhi

Total of BoQ 2 & BoQ 3

Total of BoQ 2

Total of BoQ 3

Percentage BoQ

BoQ_Ver3.0

Name of the Bidder/ Bidding Firm / Company :

PRICE SCHEDULE (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only )

NUMBER #

CHAPTER - I: BUILDING INCLUDING INTERNAL SERVICES SH-I: EARTH WORK

Earth wok in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30cm in depth,1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50m and for all lifts, as directed by Engineer-in-charge.

All kind of soil

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30cm in depth,1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50m and all lift, as directed by Engineer-in-charge.

Ordinary rock

Hard rock (blasting prohibited)

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan) ,including dressing of sides and ramming of bottoms, for all lifts, including ,getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50m.

All kind of soil

Excavtion work by mechanical means (Hydraulic excavator) /manual means in foundation trenches of drains (not exceeding 1.5m in, width or 10sqm on plan), including dressing of sides and ramming of bottoms, all lift, including getting out the excavated soil and disposal of surplus excavated soils as directed,within a lead of 50m.

Ordinary rock

Hard rock(blasting prohibited)

Filling available excavated earth (excluding rock) in trenches, plinth,sides of foundations etc, in layers not exceeding 20cm in depth, consolidating each deposited layers by ramming and watering, lead up to 50m and all lifts.

Excavating, supplying, stacking and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in foundation trenches, plinth, sides of foundation etc. complete for all lift.

Supplying and filling in plinth with sand (Jamuna sand) under floors, including watering ramming, consolidating and dressing complete.

Supplying chemical emulsion in sealed containers including delivery as specified.

Chlorpyriphos/Lindane emulsifiable connectrate of 20%

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termitte treatment (excluding the cost of chemical emulsion):

Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc.

With chlorpyriphos/Lindane E/C 20% with 1% concentration

Treatment of soil under existing floors using chemical emulsion @ one litre per holes, 300mm apart including drilling 12mm diameter holes and plugging with cement mortar 1:2(1 cement :2 coarse sand) to match the existing floor:

With chlorpyriphos/Lindane E.C 20% with 1% concentration

SH-II : CONCRETE WORK

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering -All work up to plinth level:

1:2:4 (1 cement : 2 coarse sand (zone-Ill) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources).

Providing and laying cement concrete in retaining walls, return walls, walls(any thickness ) including attached pilasters,columns,piers, abutments, pillars, posts , struts, buttresses,string or lacing courses, parapets, coping ,bed blocks, anchor blocks, plain window sills, fillets,sunken floor etc, up to floor five level, excluding the cost of centering, shuttering and finishing:

1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20mm nominal size derived from natural sources).

Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specification.

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of stone 40 mm down aggregate size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

SH-III :REINFORCED CONCRETE WORK

Centering and shuttering including strutting, propping etc, and removal of form for all heights:

Foundations, footings, bases of columns , etc, for mass concrete

Walls (any thickness ) including attached pilasteres, butteresses,plinth and string courses etc.

Suspended floors, roofs, landings, balconies and access platform

Lintels, beams,plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Stairs, (excluding landings) except spiral-staircases

Extra for shuttering in circular work (20% of respective centering and shuttering items)

Weather shade , Chajjas, corbels etc, inlcuding edges

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc. including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof(plan area to be measured)

Suspended floors, roofs, landing, beams and balconies (plan area to be measured)

Steel reinforcement for R.C.C work including straightening, cutting , bending placing in position and binding all complete at all heights and levels

Thermo-Mechanically Treated bars of grade Fe-500D or more conforming to IS 1786.

Add for plaster drip course /groove in plastered surface or moulding to R.C.C projections

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Ordinary Portland cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% times of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

All works upto plinth level

Concrete of M25 grade with minimum cement content of 330 kg /cum

Concrete of M30 grade with minimum cement content of 350 kg /cum

All work above plinth level upto floor V level

Concrete of M25 grade with minimum cement content of 330 kg /cum

Concrete of M30 grade with minimum cement content of 350 kg /cum

Extra for R.C.C./ B.M.C/ R.M.C. work above floor V level for each four floors or part thereof.

Add for using extra cement in the items of design mix over and above the specified cement content therein.

Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Kentledge/Anchor piles method and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer in-charge.

Single pile upto 50 tonne Safe capacity

Initial test (Test Load 2.5 times the Safe capacity)

Routine test (Test Load 1.5 times the Safe capacity)

Providing, driving with hydraulic piling rigs with power units and installing driven cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of shoe and the length of pile to be embedded in the pile cap etc. all complete. (Length of pile for payment shall be measured from top of shoe to the bottom of pile cap) :

450 mm dia piles

SH - IV : MASONRY WORK

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in :

Cement mortar 1:4 (1 cement : 4 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :

Cement mortar 1:6 (1 cement : 6 coarse sand)

Providing and laying Autoclaved Aerated concrete (AAC) blocks masonry 100 mm/ 125 mm thick with Grade-I AAC blocks of density 551 to 650 kg/ cum conforming to IS: 2185 (Part 3) in super structure above plinth level up to floor V level in cement mortar 1:4 (1 cement : 4 coarse sand). The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work.

Providing and laying Autoclaved Aerated concrete (AAC) blocks masonry with 150mm to 300 mm thick with Grade-I AAC blocks of density 551 to 650 kg/ cum conforming to IS: 2185 (Part 3) in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).

Extra for AAC block masonry / Tile brick masonry in superstructure above floor V level, for each four floors or part thereof by mechanical means.

SH - V : CLADDING WORK

Stone work (machine cut edges) for wall lining etc. (veneer work) upto 10 metre height, backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement: 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately) :

Gang saw cut stone

18 mm thick Granite stone

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platform, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Granite stone slab of colour black, Cherry/Ruby red

Area of slab upto 0.50 sqm

Area of slab over 0.50 sqm

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.

Granite work

Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete.

Extra for providing opening of required size & shape for wash basin/kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth.

Granite stone of approved shade

Providing and fixing stainless steel cramps of required size and shape for anchoring stone wall lining to the backing or securing adjacent stones in stone wall lining in cement mortar 1 : 2 (1 cement: 2 coarse sand), including making the necessary chases in stone and holes in walls wherever required.

Providing and fixing copper pins 7.5 cm long 6 mm diameter for securing adjacent stones in stone wall lining in cement mortar 1:2 (1 cement : 2 coarse sand), including making the necessary chases.

Providing and fixing dry cladding on walls at all height with 30 mm thick gang saw cut stone with machine cut edges of uniform colour and size upto 1mx1 m, fixed to structural steel frame work and/ or with the help of cramps, pins etc. and sealing the joints with approved weather sealant as per Architectural drawing and direction of Engineer-in-charge. (The steel frame work, stainless steel cramps and pins etc. shall be paid for separately).

Red sand stone - 30 mm thick gang saw cut stone

White sand stone - 30 mm thick gang saw cut stone

Providing and fixing structural steel frame (for dry cladding with 30 mm thick gang saw cut with machine cut edges sand stone) on walls at all heights using M.S. square/ rectangular tube in the required pattern as per architectural drawing, including cost of cutting, bending, welding etc. The frame work shall be fixed to the wall with the help of M.S. brackets/ lugs of angle iron/ flats etc. which shall be welded to the frame and embedded in brick/PCC/RCC block wall with cement concrete block 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20 mm nominal size) of size 300x230x300 mm, including cost of necessary centring and shuttering and with approved expansion hold fasteners on CC/RCC surface, including drilling necessary holes. Approved cramps/ pins etc. shall be welded to the frame work to support stone cladding, the steel work will be given a priming coat of Zinc primer as approved by Engineer-in-charge and painted with two or more coats of epoxy paint (Shop drawings shall be submitted by the contractor to the Engineer-in-charge for approval before execution). The frame work shall be fixed in true horizontal & vertical lines/planes. (Only structural steel frame work shall be measured for the purpose of payment, stainless steel cramps shall be paid for separately and nothing extra shall be paid).

Providing and fixing adjustable stainless steel cramps of approved quality, required shape and size, adjustable with stainless steel nuts, bolts and washer (total weight not less than 260 gram), for dry stone cladding fixed on frame work at suitable location, including making necessary recesses in stone slab, drilling required holes etc complete as per direction of the Engineer-in-charge.

SH - VI : WOOD & PVC WORK

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).

Second class teak wood

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:

35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.

35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Extra for Providing and fixing flush doors with decorative veneering instead of non decorative ISI marked flush door shutters conforming to IS: 2202 (Part I) (a) On one side only

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass excluded) (overall area of door shutter to be measured):

Rectangular or square

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete :

2nd class teak wood 50x12 mm

Providing and fixing carbon steel galvanised (minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 mm dia polyamide PA 6 grade sleeve, including drilling of hole in frame, concrete/ masonry, etc. as per direction of Engineer-in-charge.

Providing and fixing IS:12817 marked stainless steel butt hinges Dorma Model No. BB4330 or approved equivalent with stainless steel screws etc. complete:

Providing and fixing heavey duty stailess steel tower bolts, ISI marked, transparent or dyed to required colour or shade, with necessary screwa etc. complete. Make - Dorma or equivalent.

Providing and fixing pull handle of Dorma Model No. TGDID 300 or approved equivalent back to back with adjustable fixing for glass, wood and metal doors in satin stainless steel. The pull handles should have supporting washer with raised bevelling on the outer surface. Length 300mm, 22mm dia SS304.

Providing and fixing floor stop half dome with 45mm dia of Dorma Model No. 3108 or approved equivalent with fixing with necessary accessories in SS 304 grade satin stainless steel.

Providing and fixing lever handle under roses of Dorma model No. TH 126WC or approved equivalent WC indicator bold and spindle in stin standard Steel including 775 sash lock with 55 mm backset, 78 mm centre and 20 mm square forend complete set including the fixing accessories.

Providing and fixing Dorma model No. ITS96 or approved equivalent concealed cam action door closer with G96N slide channel arm with with standard spindle including cushioned limit stay. Spring size EN 2-4 as per EN1154 and CE Marked silver finish non-handled version.

Providing and fixing aluminium handles, ISI marked powder (powder coating not less than grade AC 10 as per IS : 1868) transparents or dyed to required colour or shade, with necessary screws etc. complete.

Providing and fixing mortice dead lock of Dorma Model No. 778 or approved equivalent with 55mm backset, 20mm square forend prepared for euro profile cylinder including strike plate in satin stainless steel as per DIN 1825-1, Class -III, including EPC 60mm length both side key operation and escutcheons ST 6612 in SSS fin.

Providing and fixing 50 mm dia and 62 mm long rubber back door buffer fixed on back side of shutter with necessary required S.S screws all complete as per the direction of Engineer-in-charge.

Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm all complete.

With 12 mm mild steel U beading

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).

Providing and fixing universal centre lock US20 with EPC & LKP locks for glass door. Make Dorma or equivalent

Providing and fixing fire resistant door frame of section 50 x 60 mm on horizontal side & 35 x 60 mm on vertical sides having built in rebate made out of 1.6 mm thick GI sheet ( Zinc coating not less than 120gm/m²) suitable for mounting 120 min Fire Rated Glazed Door Shutters. The frame shall be filled with Mineral wool Insulation having density min 96Kg/m³ . The frame will have a provision of G.I. Anchor fastners 14 nos ( 5 each on vertical style & 4 on horizontal style of size M10 x 80 ) suitable for fixing in the opening along with Factory made Template for SS Ball Bearing Hinges of Size 100x89x3mm for fixing of fire rated glazed shutter. The frame shall be finished with a approved fire resistant primer or Powder coating of not less than 30 micron in desired shade as per the directions of Engineer - in- charge . (Cost of SS ball bearing hinges is excluded).

Providing and fixing 60 mm thick glazed fire resistant door shutters of 120 min Fire Rating confirming to IS:3614 (Part II) or EN1634- 1:1999, tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical styles, top rail & side rail 60 mm x 60 mm wide and bottom rail of 110 mm x 60 mm made out of 1.6mm thick G.I. sheet (zinc coating not less than 120gm/m²) duly filled mineral wool insulation having density min 96 kg/m³ and fixing with necessary stainless steel ball bearing hinges of size 100x89x3mm of approved make, including applying a coat of approved fire resistant primer or powder coating not less than 30 micron etc all complete as per direction of Engineer-in-charge (panelling to be paid for seperately).

Providing and fixing glazing in fire resistant door shutters, fixed panels & partitions etc., with G.I. beading made out of 1.6 mm thick G.I. sheet (zinc coating not less than 120 gm/m²) of size 20 x 33 mm screwed with M4 x 38 mm SS screws at distance 75 mm from the edges and 150 mm c/c , including applying a coat of approved fire resistant primer/powder coating of not less than 30 micron on G.I. beading, & special ceramic tape of 5 x 20 mm size etc complete in all respect as per NBC 2016, IS 16231 (Part 3): 2016 and as per direction of Engineer-in-charge with glass of required thickness having 120 minutes of fire resistance both integrity & radiation control (EW120) and minimum 20 min of insulation (EI20). The manufacturer have to give test report/certification of fire glass and the glass should have the stamp showing the value of E, EW & EI. The glass shell be tested in approved NABL accredited lab or by any other accredition body which operstes in accordance with ISO/IEC 17011 and accredits labs as per ISO/IEC 17025 for testing and calibration scopes shall be eligible. The maximum glazing size shall not be more than 1100x2200mm (w x h) or 2.42 sqm.

SH - VII : STEEL WORK

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

Hot finished welded type tubes

Providing and fixing stainless steel (Grade 304) railing, made of Hollow tubes, channels,plates etc. including welding, grinding, buffing, polishing and making curvature(where required) and fixing the same with necessary stainless steel nuts and bolts complete i/c fixing the same with necessary accessories & stainless steel dash fastener, stainless steel bolts etc of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts. bolts, fasteners etc)

SH-VIII : FLOORING

Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator, vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-in-charge. (The panel shuttering work shall be paid for separately). (Note:- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/ recoverable separately).

Centering and shuttering including strutting, propping etc. and removal of form for

Edges of slabs and breaks in floors and walls

Under 20 cm wide

Precast terrazo tiles 22 mm thick with graded marble chips of size upto 12 mm, laid in floors, and landings, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20 mm thick bed of cement mortar 1 : 4 (1 cement:4 coarse sand):

Light shade pigment using white cement

Marble stone flooring with 18mm thick as per sample of marble approved by Engineer-in-charge ,over 20mm(average) thick base of cement mortar 1:4 (1 cement :4 coarse sand ) laid and jointed with grey cement slurry, including rubbing and polishing complete with:

Raj Nagar plain

Black Zebra

Udaipur green marble

Kota stone slab flooring over 20mm(average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab,including rubbing and polishing complete with base of cement mortar 1:4 (1 cement :4 coarse sand ).

25 mm thick

Kota stone slabs 20mm thick in risers of steps, skirting , dado and pillars laid on 12mm (average) thick cement mortar 1:3 (1 cement :3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Extra for kota stone/sand stone in treads if steps and risers using single length up to 1.05metre

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 1 8 mm thick stone slab over 20 mm (average) thick base of cement mortar 1 : 4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.

Polished Granite stone slab of colour Black, Cherry/Ruby Red or equivalent

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufactured), of approved make, in all colours, shades except burgundy bottle green , black of any size as approved by Engineer-in-charge in, skirting, risers of steps and dados, over 12mm thick bed of cement mortar 1:3(1 cement :3 coarse sand ) and jointing with grey cement slurry @3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying antiskid Ceramic floor tiles of approved size (thickness to be specificed by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colour such as White, Ivory, Grey ,Fume Red, Brown, laid on 20mm cement slurry @3.3kg/sqm including pointing the joints with white cement and matching pigment etc. complete.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.

Double charge vitrified tile polished finish of size

Size of Tile 600x600mm

Size of Tile 600 x 1200 mm

Size of Tile 1000 x 1000 mm

Providing and laying double charged Vitrified tiles in different sizes (thickness to be specified by manufacture),with water absorption less than 0.08% and conforming to I.S 15622, of approved make, in all colours & shade m in skirting riser of steps, over 12mm thick bed of cement slurry @3.3/sqm including grouting the joint with white cement & matching pigment etc. complete.

Size of Tile 600x600mm

Size of Tile 600x1200mm

Size of Tile 1000 x 1000 mm

38 mm thick wood block flooring of first class teak wood laid over 25 mm thick leveling layer of cement concrete 1:2:4 (1 cement : 2 coarse sand: 4 graded stone aggregate 1 0 mm nominal size) to be paid separately, coated with a thin layer of hot bitumen penetration 80/25 (blown type) @ 2.45 kg per sqm, including fixing blocks in position after dipping in hot bitumen (blown type) up to half depth, planed, levelled smooth and finished complete.

SH- IX : ROOFING

Providing and fixing false celling at all height inluding providing and fixing of frame work made of special section , power pressed from M.S sheets and galvanised with zinc coating of 120gms/sqm(both side inclusive) as per IS: 277and consisting of angle cleats of size 25 mm wide x1.6mm thick with flanges of 27mm and 37mm, at 1200mm centre to centre, one flanges fixed to the ceiling with dash fastener 12.5mm dia x50m long , with 6mm dia bolts, other flanges of cleat fixed to the angle hanger of 25x10x0.50mm of required length with nuts& bolts of required size and other end of angle hanger fixed with intermediate G.I channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I intermediate channel with conneting clips made out of 2.64mm dia x230mm long G.I wire at every junction, including fixing perimeter channels 0.5mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450mm centre, with 25mm long dry wall screws @230 mm interval,including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25mm at 230mm c/c ,including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacture's specification and also including the cost of making opening for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in charge but excluding the cost of painting with

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks)

12.5 mm thick tapered edge Glass Reinforced Gypsum (GRG) board conforming to IS: 2095- (Part 3):1996 (Boards with BIS certification marks)

12.5 mm thick tapered edge gypsum moisture resistant board

Supplying, fitting & fixing Profiled polycarbonate sheet in Roof of approved make & brand conforming to IS: 14443-1997 and having 50 micron UV protection layer under co-extrusion technology, Fire rating being B-s1 as per EN13501-1 certification, fitted and fixed with 60mm wide aluminium channel section top and bottom member in dry-glaze sandwitch system, (unit wt. of top and bottom members: 0.375 kg/m & 0.69 kg/m) of approved brand and profile, EPDM quality rubber gaskets, anti dust tape, end closer "C" channel and 75 mm long Self tapping screw being drilled through the centre leg of the bottom section with nuts placed at 300 mm apart without anyway puncturing the polycarbonate sheet, EPDM Washer 16 mm dia & 3 mm thick washer etc complete strictly as per manufacturers specification and direction of Engineer-in- Charge. Natural/ Blue/Green/Bronze/Opal/ Metallic grey colour. With 2 wall 8 mm overall thickness (wt.1.50kg/sqm,Ugvalue being 3.3 W/m2K, Min. cold bending radius of 1200 mm). Make / Manufacturer / Brand for Polycarbonate & Gutter: LEXAN / TUFLITE / PALRAM / GALLINA or equivalent standard make

Supplying, fitting & fixing Polycarbonate eaves gutter in Roof of approved make & brand conforming to IS: 14443-1997 fitted and fixed with necessary fittings for fixing, bent to design, bolts, nuts, washers and necessary lapping at all heights, and size as per site condition etc. complete.

Providing and fixing false ceiling at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity < 0.043 W/m K as per ASTM 518:1991, in true horizontal level suspended on inter-locking metal powder coated T-Grid of hot dipped galvanised iron section of 0.40 mm thick on Silhouette profile,rotary stiched double webbed white with 6 mm reveal profile (white/ black),comprising of main-T runners of size 15x42 mm of length 3000 mm, cross - T of size 15x42 mm of length 1200 mm and secondary

intermediate cross-T of size 15x42 mm of length 600 mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size 22x19x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall S.S screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge.

Providing & fixing false ceiling at all height including providing & fixing of framework made of special section, power pressed from M.S. sheets and galvanised with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleat of size 25mm wide x 1.6mm thick with flanges of 27mm and 37mm, at 1200mm c/c, one flange fixed to the ceiling with dash fastener 12.5mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25 x10 x0.50mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I chanels 45 x15 x 0.90mm running at the spacing of 1200 mm c/c, to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26 mm each having lips of 10.5mm, at 450mm c/c, shall be fixed in a direction perpendicular to G.I intermediate channel with connecting clip made out of 2.64mm dia x 230mm long G.I wire at every junction, including fixing perimeter channels 0.50mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/ partitions with the help of Rawl plugs at 450mm centre, with 25mm long dry wall screws @ 230mm interval, including fixing of Calcium Silicate Board to ceiling section and perimeter channels with the help of dry wall screws of size 3.5 x25mm at 230mm c/c, including jointing & finishing to a flush finish of tapered and square edges of the board with recommended jointing compounds, jointing tapes,finishing with jointing compounds in three layers covering up to 150mm on both sides of joints and two coats of primer suitable for boards, all as per manufacture’s specification and also including the cost of making opening for light fittings, grills, diffusers, cut outs made with frame of perimeter channels suitably fixed, all complete as per drawings, specificaton and direction of the Engineer in charge butexcluding the cost of painting with:

Providing & fixing false ceiling at all height including providing & fixing of framework made of special section, power pressed from M.S. sheets and galvanised with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleat of size 25mm wide x 1.6mm thick with flanges of 27mm and 37mm, at 1200mm c/c, one flange fixed to the ceiling with dash fastener 12.5mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25 x10 x0.50mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I chanels 45 x15 x 0.90mm running at the spacing of 1200 mm c/c, to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26 mm each having lips of 10.5mm, at 450mm c/c, shall be fixed in a direction perpendicular to G.I intermediate channel with connecting clip made out of 2.64mm dia x 230mm long G.I wire at every junction, including fixing perimeter channels 0.50mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/ partitions with the help of Rawl plugs at 450mm centre, with 25mm long dry wall screws @ 230mm interval, including fixing of Calcium Silicate Board to ceiling section and perimeter channels with the help of dry wall screws of size 3.5 x25mm at 230mm c/c, including jointing & finishing to a flush finish of tapered and square edges of the board with recommended jointing compounds, jointing tapes,finishing with jointing compounds in three layers covering up to 150mm on both sides of joints and two coats of primer suitable for boards, all as per manufacture’s specification and also including the cost of making opening for light fittings, grills, diffusers, cut outs made with frame of perimeter channels suitably fixed, all complete as per drawings, specificaton and direction of the Engineer in charge butexcluding the cost of painting with:

With 15 mm thick integral densified micro edge light weight calcium silicate false ceiling tiles

Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance > 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm ) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised @80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size 24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be prepainted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the engineer-in-charge.

With 16 mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.55 to 0.6)

SH- X : WATER PROOFING

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of:

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of: (ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. (iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area. (iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/ sqm).

Providing and laying integral cement based water proofing, treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc. consisting of following operations

Applying a slurry coat of neat cement using 2.75kg/ sqm. Of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300mm height including cleaning the surface before treatment

Laying brick bats with mortar using broken brick bats 25mm to 115mm size with 50% of cement mortar 1.5(1cement :5coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20mm thick layer of cement mortar of mix 1.5(1cement :5 coarse sand ) admixed with water proofing compound conforming to IS :2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300mm height including rounding of junctions of walls and slabs

After two days of proper curing applying a second coat of cement slurry suing 2.75kg/sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge

Finishing the surface with 20mm thick jointless cement mortar of mix 1:4(1 cement :4 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300mm square 3mm deep

The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineer-in-charge.

With average thickness of 120mm and minimum thickness at khurra as 65mm

Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge decketc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI- 212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage.

For vertical surface two coats @ 0.70 kg per sqm

For horizontal surface one coat @1.10 kg per sqm.

Providing and Placing in position suitable PVC water stops conforming to IS:12200 for construction/ expansion joints between two RCC members and fixed to the reinforcement with binding wire before pouring concrete etc. complete :

Dumb bell with central bulb (180 mm wide, 8 mm thick)

SH-XI : FINISHING

12 mm cement plaster of mix :

1:6(1 cement : 6 fine sand )

6 mm cement plaster of mix :

1:3 (1 cement : 3 fine sand)

Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturer

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Finishing walls with water proofing cement paint of required shade

New work (Two or more coats applied @3.84kg/10sqm)

Applying priming coat:

With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:-

Two or more coats on new work

French spirit polishing :

Two or more coats on new works including a coat of wood filler.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour.

Two coats

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content.

With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre

SH-XII : SANITARY INSTALLATION

Providing, fixing, testing and commissioning of white vitreous china wall mounted European water closet including providing & fixing CP bolts, nuts, fisher / anchor bolt are required for hangong of WC, nuts, supporting arrangements, bakelite/poly propylene seat & cover with CP hinges & rubber buffers, WC pan connector (straight /offset type Macfit single body push fit type WC pan connector with factory supplied spring loaded seal guard of McAlpine, UK with integral single mould sealing fins made of flexible EVA body, including bush/adaptor for use with C.I. Pipe as supplied with the pan connector) complete with all accessories. Including cutting & making good the walls & floors wherever required.(Make: Jaquar : Cat no. CNS-WHT-961SPP & PLATE-JCP-CHR-392415 or equivalent).

Providing, fixing, testing and commissioning of concealed type cistern with dual flush facility (3 / 6 Ltr.) comprising of actuator button facia assembly including brass / SS screws and washer complete.(Make:Jaquar:Cat no. JCS-WHT-2400WP or equivalent).

Providing, fixing, testing and commissioning of star white colour vitreous china under counter circula Wash Basin (Size 560 x 430 mm or as/architectural detail drawing) with CP brass waste assembly complete including CI / MS brackets duly painted, cutting and making good the walls floors wherever required.(Make: Jaquar:Cat no.FLS-WHT-5701 or equivalent).

Providing, fixing, testing and commissioning of CP brass bottle trap with wall connection pipe for wash basins. (Make: Jaquar: Cat no. ALD-769L250x190 or equivalent).

32 mm dia

Providing and fixing 600 x 450mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete in all respect

Providing, fixing, testing and commissioning of CP Braided hoses connection 450 mm long including nuts and washers and making connection to fixtures and fittings complete as required. (Make: Jaquar:Cat no. ALD-803AB or equivalent).

15 mm dia nominal bore

Providing and fixing SS liquid soap container with 1000 ML capacity and brackets fixed to wall with wooden cleats and C.P. brass screws, including cutting and making good the walls wherever required complete in all respect. (Make: Eurunics:Cat no. ES04 or equivalent).

Providing and fixing C.P. brass toilet paper holder.(Make: Jaquar:Cat no. ACN-1151N or equivalent).

Providing and fixing CP brass twin coat hooks fixed on toilet door/wall with CP brass screws, complete in all respect. (Make: Jaquar:Cat no. ACN-1161N or equivalent).

Providing and fixing stainless steel kitchen sink A ISI 304 (18/8) as per I.S.13983 with C.I brackets and stainless steel plug 40mm including painting of fittings and brackets, cutting and making good the walls wherever required complete in all respect.

Kitchen sink with drain board 510 x 1040 bowl depth 200 mm

Providing, fixing, testing and commissioning of C.P. brass pressmatic pillar cock with CP wall flange complete as required with flow rate of 3.8 LPM complying to Green Building requirements.(Make: Jaquar:Cat no. PRS-031 or equivalent).

15 mm nominal dia.

Providing and fixing of CP brass wall mounted sink cock with C.P. wall flange, swinging spout complete as required with flow rate of 3.8 LPM complying to Green Building requirements. (Make : Jaquar -Model No. FLP-5347PM or equivalent)

Providing, fixing, testing and commissionin of white vitreous china large flat back / half stall urinal including providing & fixing CI / MS bracket (duly painted with 2 coats of paints over a coat of primer), including CP brass waste with dome type grating, wall flanges complete with all accessories.(Make: Jaquar : Cat no. URS-WHT-13253N or equivalent).

Providing, fixing, testing and commissioning of automatic flushing systems for urinal to ensure pre-flush & flushing only immediately after use, comprising of all plumbing, electronic and electrical items suitable power supply 240volt AC. CP wall flange, infrared photo cells, eyes electrically operated solenoid valve, step down transformer / equipment and any other item required to provide satisfactory functioning. (Make: Euronics Cat no. EU44BE or equivalent).

Providing, fixing, testing and commissioning of CP brass bottle trap with wall connection pipe for urinals. (Make: Jaquar: Cat no. ALD-769L250x190 or equivalent).

Providing and Fixing, testing & commissioning of CP brass Health Faucet (complete with hook and flexible tube min. Length 1.0 m) as required complete in all respect with flow rate of 3.8 LPM complying to Green Building requirements.(Make: Jaquar: Cat no. ALD-573 or equivalent).

Providing and Fixing, testing & commissioning of C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931. (Make : Jaquar : Cat no. FLR-5053N or equivalent).

15 mm nominal bore

Providing and fixing of Nickel Chromium Plated towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour, of approved brand & manufacture complete as per direction of Engineer in Charge.Make :Jaquar -Model No. ACN 1111 NM or equivalent)

600 mm long towel rail

SOIL, WASTE, RAIN WATER AND VENT PIPES

Providing, fixing, testing and commissioning of sound insulated Polyproplene piping system from as per EN 1451-Part 1-6 & EN 12056 Part 1-5 with 3 layer pipe made of PP-C + PP-MV + PP-C in Blue Ral 5014 (halogen and calcium free) colour, push-fit type, food safe, having high impact and stiffness, offering sound levels of not more than 22 dBA as per DIN 4109 at a flow rate of 4 l/s and having pipe ring stiffness as per 1S0/DIS 9969 and tightness as per EN 1277/B and C and DIN 19560, density of pipe = 1.25gms/m3, elongation = 0.05mm/m0K and tensile strength > 24 N/mm2,with all necessary fittings in blue colour, fitted with factory fitted lip ring. Pipes may be laid under slung from ceiling. The installation shall be complete in all respects including cutting chases / holes in walls, slabs and making good the same as per specifications. (For Soil, Waste & Vent pipes).

75 mm dia

110 mm dia

160 mm dia

Providing, fixing, jointing, testing and commissioning PVC (Class III) of pressure rating 6.0 kg/sqcm Rain water downtake pipe conforming to IS:4985 cut to required lengths including all necessary fittings and specials. Fixing at wall/ceiling level supported by galvanized steel clamps & hangers etc. as required for proper seismic loading as per the calculations. Making proper connection with cement solvent joint as per BIS / manufacturer. Cutting chases/holes in floors / walls / slab.

75 mm dia

110 mm dia

160 mm dia

Providing, fixing, testing & commissioning of P Trap in Polypropylene (PP) Construction with Sealing flange, with removable trap, 50 mm water seal, with protection plug, with three rotratable inlets of 50mm dia, with horizontal drain socket, with 100 mm outlet, with height adjustable piece suit to site requirements. Quality controlled in accordance with DIN EN -1253

110 mm inlet and 110 mm outlet.

Providing, fixing, testing & commissioning of Bathroom Drain in Polypropylene (PP) Construction with Sealing flange,without trap,without top, with protection plug, with vertical drain socket, with outlet 50 mm dia, With height adjustable and rotratable top frame Quality controlled in accordance with DIN EN -1253

Providing, fixing, testing and commissioning of sound insulated Polyproplene piping system from as per EN 1451-Part 1-6 & EN 12056 Part 1-5 with 3 layer pipe made of PP-C + PP-MV + PP-C in Blue Ral 5014 (halogen and calcium free) colour, push-fit type, food safe, having high impact and stiffness, offering sound levels of not more than 22 dBA as per DIN 4109 at a flow rate of 4 l/s and having pipe ring stiffness as per 1S0/DIS 9969 and tightness as per EN 1277/B and C and DIN 19560, density of pipe = 1.25gms/m3, elongation = 0.05mm/m0K and tensile strength > 24 N/mm2,with all necessary fittings in blue colour, fitted with factory fitted lip ring. Pipes may be laid under slung from ceiling. The installation shall be complete in all respects including cutting chases / holes in walls, slabs and making good the same as per specifications. Pipes laid in floors shall be encased with 40 mm thick concrete all around, complete in all respects including testing of complete installation.(For Soil & Waste pipes)

Providing and fixing PVC WC connector (straight or bend type) with rubber lip ring. Including 110 mm dia PVC pipe / bend of required length and proper connection with M seal to C.I. pipe complete as required

Providing and fixing Heavy class SS grating with cockroach trap of approved design including setting in floor with cement motor to match with floor finish as per architect requirement.

Size 100 mm x 100 mm

Size 125 mm x 125 mm

Providing and fixing cleaning eye / Clean out plug on horizontal soil & waste pipes, with opening arrangements for soil / waste pipe and other necessary fittings inlcuding jointing, to the satisfaction of the Project Manager / Consultants.

For 110 mm dia pipe

For 160 mm dia pipe

Supply, installation, testing and commissioning of GI pipes Class 'C' (heavy duty) of approved make conforming to IS 1239-1982 complete with G.I. fittings heavy class such as tees, crosses, plugs, sockets, elbows, reducers, unions, sleeve pieces, check nuts etc. including jointing (wherever required), clamps/structural steel supports as required/directed at site, cutting & making good the walls, floors, RCC. work etc. including cutting chases & filling the same. (The rate includes the cost of two coat of primer and two coat of enamel paint and pypcote wrapping for the underground pipe) (For Sump riser line).

80 mm dia

100 mm dia

SH-XIII : WATER SUPPLY

Providing and fixing, testing and commissioning of chlorinated polyvinly chloride (CPVC) pipes, having thermal stability for hot & cold water pipes conforming to IS capable to withstand 27.6 kg/cm² at room tempreature water and 7.03 kg/cm² at 82°C and all fittings of CPVC SDR 11 like elbow, tee, reducers, couplers, brass threated male & female (adapoters, elbow, tees) and pipe clamps at 1.00 m spacing. The pipe fitting joining to be done with solvent cement as per manufacturers specifications & recommendations. This includes testing of joints complete as per direction of Engineer-In-charge.

Concealed work, including cutting chases and making good the walls etc.

15 mm dia nominal bore

20 mm dia nominal bore

25 mm dia nominal bore

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

Internal work - Exposed on wall

20 mm dia nominal bore

25 mm dia nominal bore

32 mm dia nominal bore

Supply, installation, testing and commissioning of GI pipes Class 'C' (heavy duty) of approved make conforming to IS 1239-1982 complete with G.I. fittings heavy class such as tees, crosses, plugs, sockets, elbows, reducers, unions, sleeve pieces, check nuts etc. including jointing (wherever required), clamps/structural steel supports as required/directed at site, cutting & making good the walls, floors, RCC. work etc. including cutting chases & filling the same. (The rate includes the cost of two coat of primer and two coat of enamel paint and pypcote wrapping for the underground pipe) (For OHT Filing line).

32 mm dia

65 mm dia

Providing & fixing full way lever operated forged brass ball valve of brass body with forged brass hard chrome plated steel ball tested to a pressure not less than 10 Kg / sqcm with threaded / flanged joints complete with nuts, bolts, gaskets, washers etc.

15 mm dia.

20 mm dia.

25 mm dia.

32 mm dia.

40 mm dia.

Providing and fixing in position of approved quality high pressure rated Gun Metal Float Valve with copper ball float and brass rods of required length suitable for test pressure of not less than 15 Kg/sqcm of the following sizes:

32 mm dia.

65 mm dia.

Supply & fixing in position ISI marked cast iron double flanged butterfly valves (PN 16) as per IS:13095, with SS disc, shaft, seating rings, internal fastening, nitrile rubber lining, nuts, bolts including transporting to worksite, 3 mm thick rubber gaskets etc. including testing, Complete as per drawings & directions of the Engineer-in-charge.

65 mm dia

80 mm dia

Providing & fixing Auto Air vent for cold water supply risers, suitable for pressure not less than 15 Kg/Sq.cm.

15 mm dia

SH -XIV : ALUMINIUM WORK

Providing and fixing aluminium work for doors, window, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS :733 and IS : 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions i.e at top, bottom and sides with required EPDM rubber/neoprene gaskter etc Aluminium sections shall be smooth, rust free, straight , mitred and jointing mechanically wherever required including cleat angle. Aluminium snap beading for glazing/paneling C.P brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge (Glazing paneling and desh fasteners to be paid separately)

For fixed portion

Powder coated aluminium (minimum thickness of powder coating 50micron)

For shutters of doors, window & ventilators including providing and fixing hinges/pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (fittings shall be be paid for separately)

Powder coated aluminium (minimum thickness of powder coatings 50micron)

Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS : 12823 Grade I type II, in panelling fixed in aluminium doors, windows shutters and partition frames with C.P brass/ stainless steel screws etc. complete as per architectural drawings and directions of Engineer-in-charge.

Pre-laminated particle board with decorative lamination on both sides

Providing and fixing glazing in aluminium door, window , ventilator shutters and partitions etc with EPDM rubber/neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge .(Cost of aluminium snap beading shall be paid in basic item)

with float glass panes of 5.5mm thickness

Filling the gap in between aluminium frame & adjacent RCC/Block/Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete

Upto 5mm depth and 5mm width

Providing fixing aluminium casement windows fastener of required length for aluminium window with necessary screws etc. complete.

Powder coated minimum thickness 50microns aluminium

Providing and fixing powder coated Garde C (minimum thickness of powder coating 50 micron as per IS:13871) aluminium grill of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved powder coated Garde C (minimum thickness of powder coating 50 micron as per IS:13871) aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment).

Providing and fixing aluminium casement stays, ISI marked, powder coated Garde C (minimum thickness of powder coating 50 micron as per IS:13871) transparent or dyed to required colour and shade, with necessary screws etc. complete.

Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including:

(a) Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)- cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard including:

(b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3 Dimentional movement for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/ masonry/structural steel framework of building structure using stainless steel anchor fasteners/ bolts, nylon seperator to prevent bimetallic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and in required numbers.

(c) Providing and filling, two part pump filled, structural silicone sealant and one part weather silicone sealant compatible with the structural silicone sealant of required bite size in a clean and controlled factory / work shop environment , including double sided spacer tape, setting blocks and backer rod, all of approved grade, brand and manufacture, as per the approved sealant design, within and all around the perimeter for holding glass.

(d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes, shapes and profiles, as required as per the site conditions, to seal the gap between the building structure and all its interfaces with curtain glazing to make it watertight.

(e) Making provision for drainage of moisture/ water that enters the curtain glazing system to make it watertight, by incorporating principles of pressure equalization, providing suitable gutter profiles at bottom (if required), making necessary holes of required sizes and of required numbers etc. complete.

This item includes cost of all inputs of designing, labour for fabricating and installation of aluminium grid, installation of glazed units, T&P, scaffolding and other incidental charges including wastages etc., enabling temporary structures and services, cranes or cradles etc. as described above and as specified. The item includes the cost of getting all the structural and functional design including shop drawings checked by a structural designer, dully approved by Engineer-in-charge. The item also includes the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working structural glazing as specified, cleaning and protection till the handing over of the building for occupation. In the end, the Contractor shall provide a water tight structural glazing having all the performance characteristics etc. all complete as required, as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer- in-Charge.

Note:- 1. The cost of providing extruded aluminium frames, shadow boxes, extruded aluminium section capping for fixing in the grooves of the curtain glazing and vermin proof stainless steel wire mesh shall be paid for separately under relevant items under this sub- head. However, for the purpose of payment, only the actual area of structural glazing (including width of grooves ) on the external face shall be measured in sqm. up to two decimal places.

Note:- 2. The following performance test are to be conducted on structural glazing system if area of structural glazing exceeds 2500 Sqm from the certified laboratories accreditated by NABL (National Accreditation Board for Testing and Calibration Laboratories), Department of Science & Technologies, India. Cost of testing is payable separately. The NIT approving authority will decide the necessity of testing on the basis of cost of the work, cost of the test and importance of the work. Performance Testing of Structural glazing system Tests to be conducted in the NBL Certified laboratories

(1) Performance Laboratory Test for Air Leakage Test (-50pa to - 300pa) & (+50pa to +300pa) as per ASTM E-283-04 testing method for a range of testing limit 1 to 200 mVhr

(2) Static Water Penetration Test. (50pa to 1500pa) as per ASTME- 331-09 testing method for a range up to 2000 ml.

(3) Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01- 05 testing method for a range upto 2000 ml

(4) Structural Performance Deflection and deformation by static air pressure test (1.5 times desing wind pressure without any failure) as per ASTME-330-10 testing method for a range upto 50 mm

(5) Seismic Movement Test (upto 30 mm) as per AAMA 501.4-09 testing method for Qualitative test. Tests to be conducted on site.

(6) Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa (35psi) upto 2000 ml

Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6 mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6 mm thick, spacer tube 12 mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor. (Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.25.2) For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm.

(i) Coloured tinted float glass 6 mm thick substrate with reflective soft coating on face # 2, + 12 mm Airgap + 6 mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement.

Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying at site all accessories and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer- in-Charge.

SH XV : AUDITORIUM INTERNAL WORKS

ACOUSTIC CEILING WORK IN AUDITORIUM

Providing Fibre Glass Acoustical Suspended Ceiling System with 1200*1200*25mm thick Optra Microlook 90 Edge Tiles with Armstrong Silhoutte grid. The tiles shall have smooth laminated visual with Humidity Resistance (RH) of 95%, NRC 0.9 -1.0(Average value of Absorption Co-efficient readings taken at 250 Hz, 500 Hz, 1000 Hz and 2000 Hz) as per ASTM C423 standard, , Light Reflectance ≥85% as per ASTM E-1477, Colour Pebble White, Fire Performance of Class 0/1 as per BS 476 Part 6/7 with 15mm Square Tegular/Microlook 90˚ edge and 8mm drop in module size of 1200 x 1200mm. It shall be suitable for Green Building application, with Recycled content of 66% (GW)/ 74% (RW).

ACOUSTICAL TREATMENT WALL PANELING

Providing G21 CHANNELLED WOODWORKS OF SIZE: 192X2400X15MM-Wall Application Channelled Woodworks perforated panels of width 192mm, thickness of 15mm and length 2400 mm, made of a Moisture resistant fibre board substrate with a laminated facing as per the approved shade (Portland Maple, Sea Beech, Siam Wood & Mystique Walnut, Interior White, Alumina Pearl) and a melamine balancing layer on the reverse side. The boards shall have a special perforation pattern where the reverse surface has a “Helmholtz” fluted perforation with consecutive 3mm wide groove followed by 21mm of visible pane. The edges of the panel shall be “tongue-and-grooved” to fix special clips for installation and seamless visual. The back of the perforated panel shall have sound absorbing non-woven Soundtex acoustical fleece hot pressed to achieve NRC of 0.5. (Average value of Absorption Co-efficient readings taken at 250 Hz, 500 Hz, 1000 Hz and 2000 Hz) as per ASTM C423 and Humidity Resistance (RH) of 70% with camber limit less than 1mm/1000mm and bow less than 1mm/300mm.

Providing and Fixing of Knauf Optra Acoustical Wall Panel with square edges made of fibre glass substrate 25mm thick, wrapped on the front side with an acoustically transparent fabric as per the approved shade (Husk, Copper, Sangria, Sesame, Coffee, Charcoal, Titanium, Flame, Peanut and Shell). The panel shall be classified for Fire Class A, as per ASTM E-84. The Acoustical Wall Panel shall be of sizes 600x600mm (Nominal) or 600x1200mm (Nominal) and shall achieve an NRC of 0.85 (Average value of Absorption Co-efficient readings taken at 250 Hz, 500 Hz, 1000 Hz and 2000 Hz) with 50mm airgap as per ASTM C423 to be fixed to wall on a framework of wooden battens and using Wall panel Impalers (supplied by the manufacturer) or by using construction adhesives (as per the instructions laid down by the manufacturer). The fibre glass substrate shall have a recycle content of 85%.

Properties of Tile Relevant Standards Base Material Fibre Glass Panel Dimensions 600mm x 600/1200mm Panel Thickness 25mm Panel Finish Acoustically transparent fabric as per the approved shade (Husk, Copper, Sangria, Sesame, Coffee, Charcoal, Titanium, Flame, Peanut and Shell). Fire Properties Class A ASTM E-84 Noise Reduction Co-efficient 0.85 ASTM C423 (Average value of Absorption Co-efficient readings taken at 250 Hz, 500 Hz, 1000 Hz and 2000 Hz) Recycled Content 85% Dimensional tolerances ± 5mm

INSTALLATION: An appropriate vapour barrier (by others) shall be applied/installed on the vertical surface before the installation to properly seal against entry of any moisture. Vapour barrier (by others) shall be installed as per Manufacturer’s recommendation. Install wooden batten grid (provided by others) of section 50x50mm or as approved by the Architect on the solid wall/partition to provide level and plumb surface. The Impalers shall be fixed to the battens using self-tapping screws, 3 nos. in case of 600x600mm and 4 nos. in case of 600x1200mm. Silica based construction adhesive (by others) to be dabbed on to the projecting elements (spikes) of the Impalers. Knauf Optra Wall Panels shall be pierced through the spikes of the Impalers ensuring the line and level of the panels are maintained.

HALL FURNISHING

Supplying and Fixing of MADE IN INDIA broadloom carpet of WELSPUN MAKE ,100% Nylon LOOP Pile , Digital Printed ,Pile Height 6.5 mm (± 1 mm),Total Height 8.5mm (± 1 mm),Stitch / 10 cm 59 (± 2% ), Pile Weight Net less Than 590 GSM (± 5% ), Total Weight 1576 GSM (± 5% ), Secondry Backing PP Mesh, Gauge 1/8 Cut Pile, Latex Natural Rubber, Color fastness to LightTest Method: AATCC 16 (20 AFU) ≥ 4.0 at 80 Hours , Static Electricity Test Method: AATCC 134 Less than 3.5 KV, Hexapod test Method: ASTM D 5252 ≥ 4, Flammability (Radiant Panel) Test Method: ASTM E 648 ≥ 0.45 (Class I) , complete as per drawing , specifications of the architect. The carpet and Underlay (min 6 -8mm) will be installed with standardSR 998/SR505/MAPAI Adhesives.The flooring to be installed as per the manufacture's specification and to be installed by its authorized agency or as Approved , with minimum 5 Years warrenty from Principal for any manufacturing defects . After Instalation carpet to be covered with transperent polythine to protect from dust,adhesive , colouring work at site . Make : Wellspun/Solo acoustics/Carpeteria

SOUND REDUCING DOOR

Supply of Double leaf Wooden Acoustic Door,76mmthick,STC45.For Acoustic Property confirming as IS:9901(PartIII)-1981,DIN:52210 PartVI-1989 ISO:16283(PartI)-2014 from CSIR-National Physical Laboratory/GQMC .as per BS:476 Part- 20 & 22 & IS 3614 part-1 & part-2 for stability, integrity and thermal insulation 03 Criteria and having a sound reduction of ≥ 45dB Acoustic Door having in fill of Rockwool 64kg/M3 density,Sandwiched betweenTwo calcium silicate boards without asbestos, Brucite and Meerschaum having a density not more than 1150kg/M3 and12 mm thick Commercial Ply both side with Bulb type EPDM Gaskets around the frame are used to enhance acoustic properties.1mm thick Mica laminates facing on both sides in desired shade and colour. HardWood Red Marrandi Door frame size is140x90mm with double rebate.Door Hardware Provision as per choice of Architect/client's approval. All complete as per Architect's/Clients approval.Door Hardware cost extra..Complete in all respect & entire satisfaction of the engineer in charge/Architect. Hardware can be used as SS Hinges, Door Closer, Door Handle, Make : 4cfire/Solo Acoustics/Sakuri

Supply & fixing of Concealed door closers (Required For All Fire Doors Except Shaft Door) as per direction of Engineer in Charge Make :Becker Fire /Dorma/Dorset as per direction of Engineer in Charge

Supply and fixing of Dorset, Hardwin, Becker Fire Solution make stainless steel 304 Grade H - Type pull handle of size 600mm long 22mm dia of approved make as per direction of Engineer in Charge. Make :Becker Fire /Dorma/Dorset

SH- XVI : INTERNAL ELECTRIFICATION

POINT WIRIG

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.

Group C

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit along with 1 No 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit along with 2 Nos 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required

2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 6 sq. mm + 1 X 6 sq. mm earth wire

4 X 10 sq. mm + 2 X 6 sq. mm earth wire

4 X 1.5 sq. mm + 2 X 1.5 sq. mm earth wire

6X 1.5 sq. mm + 3 X 1.5 sq. mm earth wire

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings).

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

Supplying and fixing 3 pin, 5 a ceiling rose on the existing junction box/ wooden block including connections etc. As required.

Numbering of ceiling fan/ exhaust fan/ fluorescent fittings as required.

wiring for group controlled (looped) light point /fan point / exhaust fan point /call bell point (with out independent switch etc) with 1.5 sq mm FRLS PVC insullated cooper conductor with single core cable in surface / recessed steel conduit , and earthing the point with 1.5 sq. mm FRLS PVC insulated cooper conductor with single core cable as required.

Group C

Supplying And FIxing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 2 nos 3 pin 5/6 A modular socket outlet and 2 nos . 5/6A modular switch , connections etc . As required ( for light plug to be used in non residential buildings)

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required as per Specification

Telephone socket outlet

TV antenna socket outlet

Bell push (For Officers Cabin)

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required.

1 or 2 Module (75mmX75mm)

Supplying And FIxing SUitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 25A modular socket outlet and 25A modular SP MCB “C” curve including connection and painting etc as required

Supply, Installation, Testing and Commissioning of ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. metal (Aluminum alloy) blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, steel/Al body Power Factor not less than 0.9,Service Value (CM/M/W) minimum as below, 350 RPM (tolerance as per IS : 374-2019), THD (Total Harmonic Distortion) less than 10%, remote (preferably mobile app based) for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Ceiling Fan compliant to IS 374:2019 fan Supply, earthing etc. complete as req

900mm, service value ≥ 5.1 CM/Min/Watt, air delivery 130 CM/Min (Minimum

1200mm, service value ≥ 6.0 CM/Min/Watt, air delivery 210 CM/Min (Minimum).

1400mm, service value ≥ 6.0 CM/Min/Watt, air delivery 245 CM/Min(Minimum)

MCCB, MCB & DB'S

Supplying and fixing following rating, four pole/Three Pole, 415 volts, "C" Curv MCB, 10kA in the existing MCB DB complete with all accessories etc. as required.

32 amps, 4P MCB

40 amps, 4P MCB

63 amps, 4P MCB

40 amps,TP MCB

63 amps,TP MCB

Supplying and fixing of 32 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 32 amps "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

SITC of KV Thermoplastic Circuit Breaker modular Boxes IP-65 with Metric knock outs for Cables entry with 3Nos IP:66 Glands.

Providing and fixing following rating and breaking capacity and pole MCCB with thermo magnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.

100 Amp, 16 KA,TP MCCB

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

6 way, double door

8 way, double door

12 way, double door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

6 way (4 + 18), Double door

8 way (4 + 24), Double door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, TPN MCCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's (but without MCB's and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)

4 way (4 + 12), Double door

8 vway (4 + 24), Double door

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts 10 KVA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Single pole

Triple pole

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. (Near AC ODU)

40 amps,4P MCB

63 amps,4P MCB

Supplying and fixing DP sheet steel enclosure on surface/ recess along with 25/32amps 240 volts "C" curve DP MCB complete with connections, testing and commissioning etc. as required.

Supplying and fixing TP sheet steel enclosure on surface/ recess along with 16/25/32amps 415 volts "C" curve TP MCB complete with connections, testing and commissioning etc. as required.

Supplying and fixing of 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 amps "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supplying and fixing of 20 amps, 415 volts, TPN industrial type, socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 20 amps "C" curve, TP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supplying and fixing 30 amps, 415 volts, TPN industrial type, socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 amps "C" curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

Providing and fixing H.T. danger notice plate of 250 mm X 200 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

CABLE TRAYS AND RACEWAY

Hot Dipped Galvanized Iron Cable Tray

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with two numbers GI Suspenders i/c base of suitable size GI angle, GI bolts & nuts, fastner etc as required.

150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

450 mm width X 50 mm depth X 2.0 mm thickness

750 mm width X 50 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "bends" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with two numbers GI Suspenders i/c base of suitable size GI angle, GI bolts & nuts, fastner etc as required.

150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

450 mm width X 50 mm depth X 2.0 mm thickness

750 mm width X 50 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Tee" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with two numbers GI Suspenders i/c base of suitable size GI angle, GI bolts & nuts, fastner etc as required.

150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

450 mm width X 50 mm depth X 2.0 mm thickness

750 mm width X 50 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Reducer" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with two numbers GI Suspenders i/c base of suitable size GI angle, GI bolts & nuts, fastner etc as required.

150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

450 mm width X 50 mm depth X 2.0 mm thickness

750 mm width X 50 mm depth X 2.0 mm thickness

RACEWAY AND JUNCTION BOX

Supplying and embedding of following sizes of under floor trunking made out of 1.6 mm thick Hot Dip Galvanised Steel sheet having compartments as indicated below including connecting pieces, floor fixing supports, chipping and levelling that portion of the floor etc in the floor in recess , including junction box etc as per specifications complete as required

300 mm x 40mm (2 compartments)

100 mm x 40mm ( 1 compartment)

EARTHING

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

Providing and fixing earth bus of 50 mm X 5 mm copper strip on surface for connections etc. as required.

Providing and fixing 32mm X 6 mm copper strip on surface or in recess for connections etc. as required.

Providing and fixing earth bus of 50 mm X 5 mm G.I strip on surface for connections etc. as required.

Providing and fixing earth bus of 32mm X6 mm G.I strip on surface for connections etc. as required.

Providing and fixing earth bus of 65mm X10 mm G.I strip on surface for connections etc. as required.

SINGLE CORE COPPER FLEXIBLE CABLE EARTHING:

Supply, laying, connection, testing and commissioning of following sizes of 1.1kV grade Single core FRLS PVC insulated Single core sheathed Cable confirming to IS:1554 with Bright annealed copper conductor for 1.1kV voltage grade. It should include both ends terminal joints providing tinned copper terminal lugs, single compression PVC cable glands up to 16 sqmm cable and double compression PVC cable glands for above, insulation tape, effecting terminal connections to the equipment complete as required.

1c x 70 sqmm Cu. sheathed FRLS cable

1c x 10 sqmm Cu. sheathed FRLS cable

1c x 6 sqmm Cu. sheathed FRLS cable

MS JUNCTION BOX

Supply, installation, testing & commissioning of MS Earthing Junction Box of size 300 X 250 X 125mm for Server & UPS earthing connections to the maintenance free earthing stations complete with 200X100X10mm CU earthing bar & provision of double earthing connectivity of CU flexible cable upto 1C X 120 sqmm with earthing station & single connectivity for server,equipment, m/c etc. with CU flexible cable upto 1C x 10/6/4 sqmm as required.

LIGHTNING CONDUCTOR

Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.

Jointing copper / G.I. tape (with another copper/ G I tape, base of the finial or any other metallic object) by riveting / nut bolting/ sweating and soldering etc as required.

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run)

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run)

Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required.

Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

MV CABLE SUPPLY, LAYING AND TERMINATION

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Upto 35 sq. mm

Above 35 sq. mm and upto 95 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Above 185 sq. mm and upto 400 sq. mm

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.

Upto 35 sq. mm (clamped with 1mm thick saddle)

Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)

Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp)

Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp)

Supplying and making cable route marker with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) of size 60 cm X 60 cm at the bottom and 50 cm X 50 cm at the top with a thickness of 10cm including inscription duly engraved as required.

MV CABLE JOINTING & END TERMINATION

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

3 X 16 sq. mm (25mm)

3½ X 35 sq. mm (32mm)

3½ X 50 sq. mm (35mm)

3½ X 70 sq. mm (38mm)

3½ X 120 sq. mm (45mm)

3½ X 150 sq. mm (50mm)

3½ X 185 sq. mm (57mm)

3½ X 240 sq. mm (62mm)

3½ X 300 sq. mm (70mm)

4 X 16 sq. mm (28mm)

4 X 25 sq. mm (28mm)

Supply of the following 1100 volts grade, Aluminium/Copper conductor, XLPE insulated, PVC sheathed, steel armoured/Unarmoured cables as per IS 7098 Part-1 and as per technical specifications of this tender and directions of Engineer-in-Charge.

4 CORES AL. CONDUCTOR

16 sq.mm. Al Ar. XLPE cable

25 sq.mm. Al Ar. XLPE cable

3.5 CORES AL. CONDUCTOR

35 sq.mm. Al Ar. XLPE cable

50 sq.mm. Al Ar. XLPE cable

70 sq.mm. Al Ar. XLPE cable

120 sq.mm. Al Ar. XLPE cable

150 sq.mm. Al Ar. XLPE cable

185 sq.mm. Al Ar. XLPE cable

240 sq.mm. Al Ar. XLPE cable

300 sq.mm. Al Ar. XLPE cable

3 CORES CU/AL. CONDUCTOR

16 sq.mm. Al Ar. XLPE cable

4 CORES Cu. CONDUCTOR

10 sq.mm. Cu. PVC Ar. cable

6 sq.mm. Cu. PVC Ar. cable

4 sq.mm. Al Ar. XLPE cable

3 CORES Cu. CONDUCTOR

10 sq.mm. Cu. PVC Ar. cable

6 sq.mm. Cu. PVC Ar. cable

4 sq.mm. Cu. PVC Ar. Cable

Supplying and making end termination with brass compression gland and Cu lugs for following size of PVC insulated and PVC sheathed / XLPE cu conductor cable of 1.1 KV grade as required.

10 sq.mm. Cu. PVC Ar. cable

6 sq.mm. Cu. PVC Ar. cable

4 sq.mm. Cu. PVC Ar. Cable

Supply, Unloading, shifting, Storing, Laying, Fixing, Testing, Commissioning & Single compression heavy duty glands of following sizes of Control Cables, Solid Copper conductor Multi stranded conductor, XLPE Insulated, cores laid up, PVC tape / Extruded Inner sheathed , Glavanised round wire Armour, extruded PVC Type, 650V grade on existing cable trays/ in existing hume pipes/ PVC pipes/ GI pipes/ on surface of slabs, walls or masonary/ RCC trenches/ ducts including cables ties, GI saddles, clamps and necessary hard ware.

6 core x 2.5 sq. mm cable

10 core x 2.5 sq. mm cable

24 core x 2.5 sq. mm cable

LIGHT FIXTURES AND FITTINGS

LED Down lighter (COB Type) (System lumen efficacy ≥120 lm/Watt)

Supplying, installation, Testing & Commissioning of LED Recessed / surface Down lighter (Round / square/ Rectangular) COB Type of following body material and construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140 270 Volt, freq 50/60 hz, Operating temp range -15 deg to 40 deg centigrade, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80 , UGR (Unified Glare Rating) < 19, Flicker free (flicker should be below 5 %), life time (LED,Driver & electrical circuitry), life time of minimum 50000 Burning Hours with , 70% of initial Lumen maintained till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin), SDCM (Standard Deviation Color Matching)

LED Panel light 2x2 ft. (System lumen efficacy ≥120 <135 lm/Watt)

Supplying, installation, Testing & Commissioning of Panel light 2x2 ft., of following body material and construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140 270 Volt, freq 50/60 hz, Operating temp range -15 deg to 40 deg centigrade, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80, UGR (Unified Glare Rating) < 19, Flicker free, (flicker should be below 5 %), life time (LED,Driver & electrical circuitry), of minimum 50000 Burning Hours with . 70% of initial Lumen maintained till life ends,CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin), SDCM(Standard Deviation Color Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard and trade mark certificate ( T.C.).Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. complete in all respect i/c connections with 1.5 sq mm FRLS, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥120 <135 lm/Watt output . LM79 & LM80 Test report from NABL lab for all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved byEngineer-in-Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C).

Powder coated die cast / Extruded aluminium Body (Thickness ≥ 1.20 mm)

Supply of LED 2ft Batten with a nominal system lumen output of 1100 lumens and a minimum system efficacy of 120 lm/W. The luminaire shall have a rated system lifetime of 50,000 burning hours at L70. The luminaire should have a color temperature of 6500K and CRI>80. The luminaire shall meet IP20 rating with THD < 10% and PF > 0.95.The Batten should be flicker free(Ripple<5%),with high cut-off Voltage at 270V and auto restart. It should have a surge protection of 4kV. The luminaire housing should made of CRCA with a PC UV shielding diffuser. The total power consumption should not exceed 30W (including driver). ". All test should be done as per IS:10322 (Part 5/Sec 3) & IEC 60598-1,IEC 60529 & Complies IEC 62384, Certification Required: LM 79 & LM 80 . Vendor should provide seperate BIS certifications for luminaire and Driver Seperately

Supply, Installation, Testing and Commissioning of Heavy duty bulkhead surface type lighting fixture 10W - 1100lm made up of pressure die-cast aluminium housing and Polyster Powder coated die cast aluminium with High quality polycarbonate diffuser in opal finish for glare free light distribution.High efficiency long life LED module with SMD LED package mounted on MCPCB with lumen efficacy of >100 lm/W. Powered by integral electronic LED driver with CCT 6500, CRI>80,THD<10%, PF>0.9, IP66, IK 09, Life class of 50,000 hrs @ L70, Operating Temperature: 0 TO +45 DEG.C; Input Supply Voltage Range:140-270 V, Frequency :50-60 HZ. Driver Safety requirement standards:IS 15885, Test Report to be submitted, Photobiological Safety Norms: IS 16108, test Certificate to be submitted, Manufacturer shall have inhouse lab approved by NABL or Ministry of Science of Govt of India. LM79 and LM80 reports must be submitted from a NABL accredited laboratory. BIS certificate for driver as well as the luminaire must be submitted for records. Driver and luminaire shall be of same make.

Supply,Installation, Testing and Commissioning of 10watt /mtr LED strip along with driver including with all accessories as required.

LT DISTRIBUTION PANEL (415V AC, 3 phase, 4 wire, 50 Hz)

ELECTRICAL PANEL

Supply,Installation, Testing and Commissioning of dust, damp and vermin proof IP- 4X free floor standing /wall mounted, Indoor type, form 3B/4A complied factory assembled in sheet steel enclosed modular construction, extendable from both side, fabricated out of CRCA grade d or equivalent sheet steel for load bearing member in 2mm thick and 1.6mm for non-load bearing members and doors with covers, 3mm thick for gland plates complete with 9 tank pre treatment process for powder coating with minimum 80 to 100 micron electro static powder coating coverage in approved shade of RAL 7032/7035 in elasto polymer type powder, complete with Aluminium bus bars designed for proper temperature rise withstand capacity, inter-connection with copper conductor wires / aluminium strips, neutral links, earth bus etc. including control wiring with 1.5sqmm. & 2.5sqmm. PVC insulated FRLS copper conductor S/C cable for voltage & current respectively, cable alleys, cable gland plates in two half for acb panels, etc. suitable for operation on 415 ±10% volts, 50 Hz AC 3 phase 4 wire system necessary metering protections & indications and mounted with the following switch gears etc. complete as required complying with IEC-61439 Part1&2 .

SDB-01 Ics = 35KA (AT GROUND FLOOR)

Incomer

1 No. Incomer 400Amps 4P MCCB with Microprocessor releases for O/C, S/C & E/F 3 Nos. phase indicating lamps to show the incoming power with control 2A TP MCB,and 1 no. digital multifunction meter with matching cast resin CT's.

One set of 4P, Al. bus bar rated 500 Amps (after considering necessary deratings of 80%) for phases and neutral for half capacity of phases.

The outgoing feeders are as follows :

2Nos. 250Amps 4P feeders each having one number 250Amps 4P MCCB.

8Nos. 63Amps 4P feeders each having one number 63Amps 4P MCCB.

7Nos. 32Amps 4P feeders each having one number 32Amps 4P MCCB.

2Nos. 20Amps 4P feeders each having one number 20Amps 4P MCB.

1 set of complete wiring

SDB-02 Ics = 35KA (FIRST FLOOR)

Incomer

1 No. Incomer 400Amps 4P MCCB with Microprocessor releases for O/C, S/C & E/F 3 Nos. phase indicating lamps to show the incoming power with control 2A TP MCB,and 1 no. digital multifunction meter with matching cast resin CT's.

One set of TPN, Al. bus bar rated 500 Amps (after considering necessary deratings of 80%) for phases and neutral for half capacity of phases.

The outgoing feeders are as follows :

9Nos. 63Amps 4P feeders each having one number 63Amps 4P MCCB.

2Nos. 40Amps 4P feeders each having one number 40Amps 4P MCCB.

3Nos. 32Amps 4P feeders each having one number 32Amps 4P MCCB.

5Nos. 32Amps DP feeders each having one number 32Amps DP MCCB.

1 set of complete wiring

SDB-03 Ics = 35KA (SECOND FLOOR)

Incomer

1 No. Incomer 200Amps 4P MCCB with Microprocessor releases for O/C, S/C & E/F 3 Nos. phase indicating lamps to show the incoming power with control 2A TP MCB,and 1 no. digital multifunction meter with matching cast resin CT's.

One set of TPN, Al. bus bar rated 200 Amps (after considering necessary deratings of 80%) for phases and neutral for half capacity of phases.

The outgoing feeders are as follows :

7Nos. 63Amps 4P feeders each having one number 63Amps 4P MCCB.

3Nos. 32Amps 4P feeders each having one number 32Amps 4P MCCB.

1 set of complete wiring

SDB-04 Ics = 35KA (THIRD FLOOR & 4th floor)

Incomer

1 No. Incomer 200Amps 4P MCCB with Microprocessor releases for O/C, S/C & E/F 3 Nos. phase indicating lamps to show the incoming power with control 2A TP MCB,and 1 no. digital multifunction meter with matching cast resin CT's.

One set of TPN, Al. bus bar rated 200Amps (after considering necessary deratings of 80%) for phases and neutral for half capacity of phases.

The outgoing feeders are as follows :

6Nos.63Amps 4P feeders each having one number 63Amps 4P MCCB.

2Nos. 32Amps 4P feeders each having one number 32Amps 4P MCB.

1 set of complete wiring

HVAC PANEL-1 (OUT DOOR TYPE) AT TERRACE

Incomer

1 No. Incomer 315Amps 4P MCCB with Microprocessor releases for O/C, S/C & E/F 3 Nos. phase indicating lamps to show the incoming power with control 2A TP MCB,and 1 no. digital multifunction meter with matching cast resin CT's.

One set of TPN, Al. bus bar rated 500 Amps (after considering necessary deratings of 80%) for phases and neutral for half capacity of phases.

The outgoing feeders are as follows :

12Nos. 63Amps 4P feeders each having one number 63Amps 4P MCCB.

1 set of complete wiring

PLUMBING PANEL-OUTDOOR TYPE

Incomer

1 No. Incomer 63Amps 4P MCCB with Microprocessor releases for O/C, S/C & E/F 3 Nos. phase indicating lamps to show the incoming power with control 2A TP MCB,and 1 no. digital multifunction meter with matching cast resin CT's.

One set of TPN, Al. bus bar rated 200 Amps (after considering necessary deratings of 80%) for phases and neutral for half capacity of phases.

The outgoing feeders are as follows :

1nos 32DP MCB 10KA.

1 set of complete wiring

MAIN LIFT PANEL Ics = 25KA

1Nos. Incomer 125Amps 4P MCCB with TM releases for O/C, S/C, 3 Nos. phase indicating lamps to show the incoming power with control 2A TP MCB,and 1 no. digital multifunction meter with matching cast resin CT's.

One set of 4P, Al. bus bar rated 200 Amps (after considering necessary deratings of 80%) for phases and neutral for half capacity of phases.

The outgoing feeders are as follows :

2Nos. 100Amps TPN feeders each having one number 100Amps TPN MCCB.

1No. 63Amps TPN feeders each having one number 63Amps TPN MCCB.

1 set of complete wiring

LIFT PANEL-01 Ics = 25KA

1Nos. Incomer 100Amps 4P MCCB with TM releases for O/C, S/C, 3 Nos. phase indicating lamps to show the incoming power with control 2A TP MCB,and 1 no. digital multifunction meter with matching cast resin CT's.

One set of 4P, Al. bus bar rated 200 Amps (after considering necessary deratings of 80%) for phases and neutral for half capacity of phases.

The outgoing feeders are as follows :

2No. 63Amps TPN feeders each having one number 63Amps TPN MCCB.

1No. 63Amps TPN feeders each having one number 63Amps DP MCB.

1 set of complete wiring

FIRE SUPPRESION SYSTEM FOR Panels

Supply Installation & commisioning of 4 Kg capacity FK-5-1-12 with UL approved 4.5 ltr water capacity non ferrous Seamless Cylinder(PESO & UL Approved) with a test pressure of 53 bar and maximum working pressure of 35bar, DLP Assembly with safety relief disc and isolation valve & UL Approved Pressure Gauge , push in connector for tube, UL approved 4kg FK-5-1-12 Gas ref NFPA 2001 FK-5-1-12 , mounting bracket, End of Line adopter with weight measuring unit to indicate loss in weight in MCU & low pressure(UL Approved) switch to indicate loss in presure in MCU, both to be used for monitoring system activation or loss of agent. Make - SVS Firetrex, Reacton, Ceasefire

Supply Installation & commisioning of 1 Kg capacity FK-5-1-12 with UL approved 1.6 ltr water capacity non ferrous Seamless Cylinder(PESO & UL Approved) with a test pressure of 53 bar and maximum working pressure of 35bar, DLP Assembly with safety relief disc and isolation valve & UL Approved Pressure Gauge , push in connector for tube, UL approved 1kg FK-5-1-12 Gas ref NFPA 2001 FK-5-1-12 , mounting bracket, End of Line adopter with weight measuring unit to indicate loss in weight in MCU & low pressure switch((UL Approved)) to indicate loss in presure in MCU, both to be used for monitoring system activation or loss of agent. Make - SVS Firetrex, Reacton, Ceasefire

Supply Installation & commisioning of Linear pneumatic heat Detection Tube :- UL Aproved Heat detection Tube, 4mm ID, 6mm OD, detection temprature 160 Deg celcius, mutlilayer, Water Absorbtion ≤ 1.5% @ 20oC and 50% RH as tested per ISO62 with fittings and supports. SVS Firetrex, reacton, Ceasefire

Supply Installation & commisioning of Master Control Unit for controlling each system along consisting Battery back for 24 hours at standyby mode with atleast 1000 eventlog, complete with pressure switches, buzzers and electronic hooters, including all necessary accessories and electrical wiring to make each entire system functional. Make - SVS Firetrex, Honeywell, Ceasefire, Seimens.

CHAPTER - II : LIFT WORK

(a) Speed 1.0 MPS

(b) Floors:- G+4

(c) Travel:- G+4 (20 MTR. approximate)

(d) Stops & Opening : from 1st door opeing level to last door opeing bottom level.

(e) Controller: Microprosessor based & AC variable voltage & variable ferquency

(f) Automatic Rescue Device complete with Dry Maintenance Free Batteries as required .

(h) Power - 415 Volts, 3 Phase, 50Hz, 4 wire system.

(i)Type of doors:

(j) Car: Power operated, center opening horizontal sliding stainless steel (Hailine) Stainless Steel false ceiling and granite flooring of approved shade/colour.

(k) Landng doors: SS landing doors in Hairline

(l)Handrail of sufficiant length at 900 mm above floor level to be fixed in the lift car.

(m) Braille operating buttons system as requred in each car and at all levels. The button shall be placed in suitable location for acccess of handicapped person.

(n) 900 center opening, 2000 mm car height

(o) Fire rated : Fire rating of 120 mintues.

(p) Ventilation : Cross flow fan.

(a) Speed 1.0 MPS

(b) Floors:- G+4

(c) Travel:- G+4 (20.00 MTR. approximate)

(d) Stops & Opening : from 1st door opeing level to last door opeing bottom level.

(e) Controller: Microprosessor based & AC variable voltage & variable ferquency

(f) Automatic Rescue Device complete with Dry Maintenance Free Batteries as required .

(h) Power - 415 Volts, 3 Phase, 50Hz, 4 wire system.

(i)Type of doors:

(j) Car: Power operated, center opening horizontal sliding stainless steel (Hailine) Stainless Steel false ceiling and granite flooring of approved shade/colour.

(k) Landng doors: SS landing doors in Hairline

(l)Handrail of sufficiant length at 900 mm above floor level to be fixed in the lift car.

(m) Braille operating buttons system as requred in each car and at all levels. The button shall be placed in suitable location for acccess of handicapped person.

(n) 900 center opening, 2000 mm car height

(o) Fire rated : Fire rating of 120 mintues.

(p) Ventilation : Cross flow fan.

CHAPTER - III : HVAC SYSTEM

VRV/VRFSystem

Outdoor Unit

Supply, Installation,Testing & Commissioning of Modular type Variable Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling and heating having 100% hermetically sealed inverter type twin Rotary/Scroll Compressor(s), minimum two compressors (with individual seperate PCB) for above 14HP modules, microprocessor based Controller, top discharge type condensing unit(s), with R-410-A Refrigerant or equivalent, vibration Isolators with suitable foundation etc. complete as required. To have better efficiency condensor fan shall be capable to operate at different speed with respect to load.The unit shall deliver the rated capacity and in confirmation as per IS 18728:2024 and CPWD Specifications and work even at 50°C ambient temperature without tripping. The system shall be able to deliver 100% of the rated capacity upto 39 Degree Celcius.The unit shall be suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply and BMS compatible. The unit shall be filled with first charge of the refrigerant and ready for use as required. The condenser should be coated with a hydrophilic film to prevent water accumulation on the surface of the heat exchanger, enhance water dispersion, and reduce the risk of degradation, thereby improving overall performance and durability. The Indian Seasonal Energy Efficiency Ratio (ISEER) of the unit shall be as per Energy Conservation and Sustainable Building Code (ECSBC) 2024 as below and complete as per CPWD specification, connections, inter connections etc. as required. (For capacity 40 and 70 ISEER 5.6 for ECSBC Building) For Cooling or Heating or Both

Indoor Units (4 Way Cassette for VRV)

Supply, Installation,Testing and Commissioning of following minimum capacity 4 way Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX Copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration Isolation, Corded remote control etc., suitable for operation on single phase 230 V ± 10%, 50Hz AC supply, complete, as required. The Indoor units must shut down upon receiving a singal from the BMS System/Fire Singnals. The system shall be capable to adjust air flow as per room requirement in auto mode. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. (Make will be same as of Outdoor)

Indoor Units (Hi-Wall for VRV)

Supply, Installation, Testing and Commissioning of following minimum capacity High wall type Indoor unit equipped with and comfort washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, outer cabinet, cord less remote control, drain pan, necessary accessories etc., suitable for operation on 230 V ± 10%, 50 Hz, single phase AC supply, complete as required. The Indoor units must shut down upon receiving a singal from the BMS System/Fire Singnals. The system shall be capable to adjust air flow as per room requirement automatically. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. (Make will be same as of Outdoor)

Ductable Unit (for VRV):

Supply, Installation, Testing and Commissioning of following minimum capacity and external static pressure VRF/VRV ceiling mounted high ductable type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, corded remote control, outer cabinet, vibration Isolators, drain pan, drain pump, other necessary supports etc., suitable for operation on single phase AC supply 230 V ± 10%, 50 Hz complete as required. The Indoor units must shut down upon receiving a singal from the BMS System/Fire Signals. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. (Make will be same as of Outdoor)

High Static Ductable units (minimum 78 pascal external static pressure)

Supply, Installation, Testing and Commissioning of following minimum capacity and external static pressure VRF/VRV ceiling mounted mid high static ductable type Indoor unit equipped with washable synthetic media prefilter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, corded remote control, outer cabinet, vibration Isolators, drain pan, drain pump, other necessary supports etc., suitable for operation on single phase AC supply 230 V ± 10%, 50 Hz complete as required. The Indoor units must shut down upon receiving a singal from the BMS System/Fire Signals. The system shall be capable to adjust air flow as per room requirement automatically. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. (Make will be same as of Outdoor)

High Static Ductable units (minimum 49 to 77 Pascal external static pressure)

CEILING SUSPENDED AHU DX TYPE

DX 'Cooling Coil Section: SS-304 construction end plates with Hydrophilic costing on Fins to be provided.

Fan Section: Fan section shall be equipped with a Single Inlet Centrifugal Impeller with High Efficiency Backward curved airfoil blades and AC motor, energy optimized for operation without spiral housing for high efficiency and favorable acoustic behavior. The minimum efficiency class of the motor shall be equivalent to IE4 suitable for continuous operation. The speed of the motor shall be varied with variable frequency drive. The fan in totality shall be of most efficient type so that the power Consumption and noise level is minimal. The motor shall be minimum IP54 protection class.

From electrical panel there shall be single input to Single AHU terminal box. All necessary internal wiring from Terminal Box to multiple direct drive motors/ Filters/ Valves/ Etc. shall be provided by AHU supplier.

High Static Ductable units (minimum 49 to 77 Pascal external static pressure)

Supply, Installation, Testing and Commissioning of following minimum capacity and external static pressure VRF/VRV ceiling mounted mid high static ductable type Indoor unit equipped with washable synthetic media prefilter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, corded remote control, outer cabinet, vibration Isolators, drain pan, drain pump, other necessary supports etc., suitable for operation on single phase AC supply 230 V ± 10%, 50 Hz complete as required. The Indoor units must shut down upon receiving a singal from the BMS System/Fire Signals. The system shall be capable to adjust air flow as per room requirement automatically. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. (Make will be same as of Outdoor)

High Static Ductable units (minimum 49 to 77 Pascal external static pressure)

5000 CFM / 14TR DX Coil / 6 RD / 50 mmwg St. Pressure(ESP).

Supply and installation of AHU Expansion Kit of AHU Connectivity kit to VRF Outdoor units with suitable Electronic Expansion valves and control box with thermostat and all accessories for 5000 CFM

Supply,Installation, testing and commissioning of Centralised Analog remote controllers for operation & status monitoring of VRV/VRF indoor units

Supply, Installation, Testing and Commissioning of Y/T/Multi Joints. Joints shall be of same Original Equipment Manufacturer (OEM) make as of ODUs and IDUs

Indoor Units

Outdoor Multi Joint

COPPER REFRIGERANT PIPING

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of 19 mm thick insulation as given below for Suction and Liquid lines, all accessories as per specifications etc. as required :

6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm

9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm

12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm

15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm

19.1 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm

22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm

28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm

34.9 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm

41.27 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm

HI - WALL SPLIT SYSTEMS

Supply , Installation, Testing and Commissioning of Air Cooled Hi Wall split type Air conditioners complete with Indoor unit(IDU), Out door unit (ODU), surface / concealed copper Refrigerant piping with insulation (closed cell elastomeric nitrile rubber tubular pipe section) upto 3 Mtr (IDU to ODU), copper power cable upto 3.5 Mtr (IDU to ODU) i/c drain pipe R-32/R-410/ R-407 Green Refrigerant, wireless Remote control, suitable for working between 180-260V with low & high voltage cutoff and 50 hz ,1 phase AC supply capable of performing cooling, dehumidification, air circulation of following capacity with Scroll / rotary compressor. The system shall be able to deliver 100% of the rated capacity upto 42 Degree Celsius. Min 5 year Original Equipment Manufacturer (OEM) warranty both compressor and Printed Circuit Board (PCB). Must comply : Electrical cable IS 694 or IS 9968 temperature sensing control IS /International Electro technical Commission (IEC) 60730, hermetic compressor IS 10617, heat exchanger IS 11329, capacitor IS 2993 and motor IS 12615. Complete as per CPWD specification and IS : 1391 Part II 2023. The system shall be able to operate up to 50 0C (out door ambient temperature).

2.0 TR with 5 Star BEE Rating

1.5 TR with 5 Star BEE Rating

Ducting

Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports, bends, transitions, reducers, end caps, collars etc as required complete in all respect in confirmation to IS : 655 and approved drawings and specifications of following sheet thickness complete as required.

Thickness 0.63 mm sheet

Thickness 0.80 mm sheet

Thickness 1.00 mm sheet

Thickness 1.25 mm sheet

Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (Class “O”) insulation on existing duct after applying suitable adhesive for Nitrile rubber. The joints shall be sealed with 50 mm wideand 3 mm thick self adhesive nitrile rubber tape insulation complete as perspecifications and as required.

Duct Acoustic Lining-Supply and Application of internal acoustic lining of supply air ducting using open cell nitrile rubber insulation with density within 140-180 Kg/m3 as per the approved shop drawings and specifications. Insulation material shall be bonded with the ducts using metal screw and washers to facilitate grip to the GI sheet.

Grilles/Diffusers:

Supply and Fixing installation, testing and commissioning of powder coated extruded aluminium Supply Air Grills with aluminium volume control dampers in confirmation to SMACNA/IS and as per specifications complete etc. as required.

Supplying & fixing of powder coated extruded aluminium Return Air Grills with louvers but without volume control dampers complete in confirmation to SMACNA/IS and as per specifications complete etc. as required.

Supply and Fixing installation, testing and commissioning of supply air diffusers of powder coated aluminium with aluminium volume control dampers with anti smudge ring & removable core in confirmation to SMACNA/IS and as per specifications complete etc. as required.

Supply and Fixing installation, testing and commissioning of Return air diffusers of powder coated aluminium without volume control dampers with anti smudge ring & removable core in confirmation to SMACNA/IS and as per specifications complete etc. as required.

Supply, installation, testing and commissioning of GI volume control duct damper complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc in confirmation to SMACNA/IS and as per specifications complete etc. as required

Fresh / Exhaust air louvers with bird screen & damper

Inline Fans : Supplying, Installing, Testing and Commissioning of Inline fans complete with motor, supporting frame, gravity louvres,etc. as per drawings and specifications. @ 15mm Static.

500 CFM Inline Fan

400 CFM Inline Fan

Drain Piping:Supply,installation,testing and commissioning of rigid PVC piping complete with fittings, supports as per specifications and duly insulated with 6 mm thick closed cell nitrile rubber class ‘O’ . Providng and fixing pipes with all necessary fittings, supports and insulation.

Control & Transmission Wiring

Supply,installation,testing and commisioning of control cum transmission wiring of 2 core x 1.5 sqmm copper in suitable 25 MM PVC conduits between indoor and out door unit & outdoor units to central remotes controllers.

CHAPTER - IV : DG SET

DIESEL GENERATOR SET-320KVA

Supply, installation, Testing & Commissioning of 'Silent Type Diesel Generating set as per CPCB IV + or better norms along with having Prime Power Rating of KVA as below, 415 volts at 1500 RPM, 0.8 lagging power factor at 415 V suitable for 50 Hz, 3 phase system & for 0.85 Load Factor, including testing at factory and site with fuel, load for test and other necessary arrangements Complete as per CPWD specifications, should have QR code which should contain drawing, test report OEM manual,Geo-Tag of manufacturing location, rating plate as per relevant IS Code etc. and consisting of the followings:

(A) Diesel Engine:

Turbocharged Diesel engine 4 stroke water cooled, multi cylinder,dynamically balanced fly wheel, electric start of suitable BHP at 1500 RPM suitable for above output of alternator at 40 Degree C, 50% RH & at 1000 Meter MSL , capable of taking 10% over loading for one hour after 12 hours of continuous operation. The engine will be with Electronic governor, Dry type Air filter with service indicator, first filling of engine fuel (after commissioning) lubricating Oil, Coolant and other consumables complete with all the required accessories, the Electronic governor shall be as per ISO 8528.The engine shall comply to the latest CPCB norms (CPCB IV + or better) and Conforming to BS 5514, BS 649, IS 10000, IS 10002, IS 13018 and as per CPWD specifications.

(B) Engine mounted Instrument Panel fitted with and having digital display for following:

(i) Start-stop switch with key

(ii) Water temperature indication

(iii) Lubrication oil pressure indication

(iv) Lubrication oil temperature indication

(v) Battery charging indication and Voltage indication

(vi) RPM indication

(vii) Over speed indication

(viii) Low lubricantion Oil trip indication

(ix) Engine Running Hours indication

(x) Fuel Level

(C) Alternator:

Synchronous alternator rated of appropriate KVA, 415 volts at 1500 RPM, 3phase 50 Hz, AC supply with 0.8 lagging power factor at 40 Degree C, 50%RH & at 1000 Meter MSL. The alternator shall be having Screen Protected Drip Proof (SPDP) enclosure IP23, brushless, continuous duty, dynamically balanced rotor, capable of taking 10% over loading for one hour after 12 hours of continuous operation, self cooled,self-excited and self-regulated through AVR conforming to IS13364(Part 2)/IS: 4722/BS 2613 suitable for tropical conditions and with class- H insulation.

(D) Base Frame & Foundation:

Both the engine and alternator shall be mounted on suitable base frame made of MS channel with necessary reinforcement which shall be installed on suitable cement concrete foundation and vibration isolation arrangement as per recommendations of manufacturer.

(E) FUEL TANK:

Daily service fuel tank of suitable liters capacity as per CPWD Specifications, fabricated out of 3 mm thick M.S. sheet complete with all standard accessories and fuel piping between fuel tank and diesel engine with MS class 'C' pipes of suitable dia. Complete with valves, level indications & accessories as required as per specifications.

(F) Exhaust System:

Dry exhaust manifold with hospital type exhaust silencer and catalytic convertor.

(G) Starting System:

12V/24V DC starting system comprising of starter motors: voltage regulator and arrangement for initial excitation complete with suitable numbers of batteries (180 AH capacity lead acid SMF type) as required as per specifications. The battery shall be housed inside the acoustic enclosure of DG Set.

(H) Acoustic and weather proof enclosure with arrangement for fresh air intake for cooling of the engine & alternator, extraction, discharging hot air in to the atmosphere and the temperature rise inside the enclosure, noise level outside enclosure. The acoustic enclosure should be suitable for cable connection/connection through bus-trunking. Such arrangements on acoustic enclosure should be water proof & dust-proof conforming to IP-65 protection. The enclosure shall be as per CPCB IV + or better norms etc. and as per CPWD specifications.

(I) AMF Panel:

Free standing floor mounted IP 42 automatic mains failure control panel including auto by-pass, suitable for KVA as below for silent type DG set complete with relays, timers, set of CTs for metering & protection and energy analyser to indicate currents, phase and line voltages, frequency, power factor, KWH, Kilo Volt Ampere Reative Hour (KVARH), KVA (Phase & Total),KW & provision for overload, short circuit, restricted earth fault, under frequency, power (aluminum) and control (copper ) cabling of suitable size upto 15 meter between AMF panel, LT Panel and DG Set including connection interconnection etc. as required, all complete and inter locking and communication/ Ethernet /RS485/SNMP port open protocol for BMS integration including suitable software, the panel shall be of DG Set OEM make etc. as per approved by Engineering in charge and including the following:

1. Suitable numbers and appropriate capacity 4 pole motorised electrically operated draw out with cradle type 3 position ACB/ MCCB with electronic release for O/C & E/F and shunt trip.

3. Protection for under and over voltage phase reversal (2 nos Over voltage relay, 2 Nos. reverse power relay and 2 Nos. under voltage relay, 2 Nos. reverse power relay and 2 Nos. under voltage relay).

4. 3 Sets of current transformers 15 P 10 accuracy for protection and 15VA class-I for metering

5. Energy analyser unit to indicate current, Voltage( L-N & L-L), kW, Kva (Phase & Total), Frequency, KWH, PF.

6. LED Indicating lamps for load on mains and load on set.

7. Fuse/ MCB for instruments.

9. Main supply failure monitor.

10. Supply failure timer.

11. Restoration timer

12. Control unit with three impulse automatic engine start/stop and failure to start lockout.

13. Impulse counter with locking and reset facility.

14. ON/OFF/Control circuit switch with indicator

15. Audio/Video annunciation for

(i) High water temperature

(ii) Low lubricating oil pressure

(iii) Engine over speed

(iv) Engine fails to start

(v) Full load/maximum load warning

16. Protection for over/under Frequency, Loss of AC sensing, Over Current, Unbalancing load with suitable number of relays and accessories

17. Maintenance notification based on Engine Run Hour & due date

18. Load Management through PLC to achieve auto opening and closing of incomer breakers, bus coupler switching of essential panel , interlocking providing signal to AMF Panel for load status and AMF shall give command to DG Set to auto start / auto stop depending upon load status and requirement etc. and necessary hardware and software required to perform the operation shall be provided by the contractor including all control wiring.

CHAPTER - V : ACCESS CONTROL SYSTEM

Access Control System with Face recognition

Supplying, Installation, Testing and Commissioning of Access Control System comprising of Face and fingerprint Recognition, Smart Card, QR Code, NFC & PIN Code based Reader, following sizes of 5” IPS TFT Touch Screens, 1GB RAM, 8 GB ROM, Live Face Detection with anti-spoofing against 2D photograph, mobile selfie & video, Fake Fingerprin and face Detection Technology, 30,000 Face storage (1:N) /, 3,000 fingerprint (1:N), QR code 30,000, 30,000 card storage (1:N), 2lakh transaction storage, 20,000 image logs, onboard dual camera (colour & IR) Primary camera min 2MP, Support Face authentication & verification from up to 1 meters, Communication protocols WiFi, TCP/IP, Wiegand Out, Wiegand IN, USB, MQTT protocol, Blacklist Employee Management, User wise authentication modes; Built in Lock Control, Mask Detection & Alert (configurable), 40 to 30,000 lux illumination, IP65 for Ingress Protection, Certification: CE, FCC, BIS, ROHS, etc. Metal Enclosure with battery backup, suitable for mounting on metal surface/metal frames/ wooden frames/wall/flap barriers including all mounting bracket & accessories complete etc. as required.

5" IPS TFT Touch Screen

Software for Web based Access Control System

Supplying, Installation, Testing and Commissioning of Web based Access Control Enrolment and Device Configuration Software, Should be independent of OS (Windows), Unified Management of Biometric, Card, and Controllers, Import Functionality for bulk user details, Biometric Template Retrieval for Data Recovery, User Management, Logs and Terminal Management, Support for IP-based and USB Biometric Devices, User-specific Access Policies, Different User Policies on the Same Terminal, Assignment of Specific Access Schedules, Pushing Users to Terminals or Groups, Admin Authority Management to define rights of each user to perform, Blacklist User Management, Access Schedule Creation, Real-Time Log Retrieval, Real- Time User Identification, Secure Storage of Biometric/Users Data, Capable to integrate with 3rd party applications over Web API's, MQTT protocol support

Electromagnetic locks

Supplying, Installation, Testing and Commissioning of Electromagnetic locks (fail safe type) for following type of Doors suitable for operation on 12 V DC having holding force 600 lbs for Single Leaf Door and 1200lbs for Double leaf door with suitable feedback i/c connection complete etc. as required.

Single leaf door

Double leaf door (Each leaf 600lbs & Total 1200 lbs)

Exit Push Button

Supplying, Installation, Testing and Commissioning of Heavy Duty SS Finish Exit Push Button for releasing access doors with all necessary installation accessories i/c connection complete etc. as required.

Door Position Sensor

Supplying, Installation Insta, Testing and Commissioning of Door Position Sensor i/e connection complete etc. as required.

CHAPTER - VI : FIRE FIGHTING / FIRE ALARM SYSTEM

a) Supply, Erection, Testing and Commissioning ofon existing foundation Fire Water Main Pump of Horizontal split casing type with a speed of 1450 RPM and of capacity 1620LPM against a total head of 50 MWC, complete with base plate, coupling, coupling guard, foundation bolts and nuts making of PCC foundation etc., complete.

b) Supply, Erection, Testing and Commissioning of SPDP squirrel Cage induction Motor suitable for 415V,3Phase,50Hz AC supply with Synchronous speed of 1500 RPM with class 'F' insulation, suitable for the pump mentioned above

a) Supply, Erection, Testing and Commissioning on existing foundation of Fire Water Jockey Pump of Horizontal end suction type with a speed of 2900 RPM and of capacity 180 LPM against a total head of 50 MWC, complete with base plate, coupling, coupling guard, foundation bolts and nuts making of PCC foundation etc., complete.

b) Supply, Erection, Testing and Commissioning of TEFC squirrel Cage Induction Motor suitable for 415V,3Phase,50Hz AC supply with Synchronous speed of 3000 RPM with Class ''F' Insulation, suitable for the pump mentioned above

Supply, Installation, Testing and Commissioning on existing foundation of diesel engine driven main fire pump suitable for automatic operation and consisting of following : complete in all respect required as under.

Horizontal / End suction type, type,multistage, centrifugal, split casing pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal to ensure a minimum pressure of 3.5 kg/sq.cm. at highest and farthest outlet at specified flow of 1620 LPM at outlet head 50 Metres conforming to IS 1520. (The pump should be capable of delivering 150 % rated discharge at a head not less than 65% of the rated head).

Suitable HP 1500 RPM diesel engine conforming to BS:649/ IS:1601 /IS:10002 all amended upto date, continuous duty,multi cylinders vertical 4 stroke cycle water cooled, developing suitable BHP at operating speed specified to drive the fire pump capable of driving continuous non-stop operation for 8 hours having 10% overload capacity for one hour in a period of 12hours continuous run, capacity to accept full load within 15 seconds from the receipt of signal to start and complete with following accessories:

i) Dynamically balanced fly-wheel. ii) Direct coupling for pump and coupling guards. iii) Radiator with hoses, fan water pump, drive arrangement and guard. iv) Air-cleaner dry type v) Fuel tank with necessary pipe. vi) Pump for lubricating oil and lubricating oil filter. vii) Electric starting system alongwith lead acid battery of suitable ampere hours 12 V / 24 V. viii) Exhaust siliencer(residential type) with necessary pipe work. ix) Governor x) Instrument panel housing all the gauges including tachometer, hour meter and starting switch with key (for manual starting xi) Necessary safety controls.and stop solenoid in the event of fault xii) Winterization arrangement. xiii) Hand operated semi-rotary hand pump for filling the service tank xiv) required length of exhaust piping as per the norms duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding (xv)Painted in post office red colour.

Common bed plate fabricated out of MS channel of suitable size for assembling the Pump and the Engine, flexible coupling and with coupling guard for protection/safety.

a) 2 Nos of Fire Water Main Pump (1 working + 1 stand-by) (300A- 02 Nos)

b) 1 No. of Jockey pump (63A- 01 No)

Supply, laying and commissioning of following size 1.1KV grade XLPE insulated armoured aluminium conductor under ground cable laid in existing trench/ humepipe/Gi Pipe etc., when laid in ground at a depth of 750mm below ground level including excavation in all kinds of soil, and refilling of earth after cables laid, providing protection with sand and bricks at sides and top and cable route markers at every 15mtr.interval and also at the turnings, identification tags at both ends. The cable shall conform to IS 7098/ Part I.

3C x 25 Sqmm armoured XLPE Aluminium conductor cable.

Laid in ground.

Laid in existing pipe/ Trench.

3C x 95 Sqmm armoured XLPE Aluminium conductor cable.

Laid in ground.

Laid in existing pipe/ Trench.

Supply and making end termination with brass compression glands and aluminium lugs for following sizes of PVC insulated, XLPE aluminium conductor cable of 1.1 KV grade all as directed.

3 core x 95 sq.mm

3 core x 25sq.mm

Supply, Erection Testing and Commissioning of Pressure Switches, with an adjustable range of 1.6 to 16 Kg/cm2 including all fixing hardware, electrical end termination and accessories etc. complete

Supply installation and testing of pipe earthing with G.I. Class B earth pipe of 3.0 metre long , 65 mm dia including accessories , and providing masonry enclosure with MS cover plate of 300 x 300mm x 6mm, having locking arrangement, wire mesh funnal with charcoal and salt as per IS 3043-1987 and directed by Engineer-in-charge.

Supply and laying of 25 x 5mm GI strip laid in ground or on surface or in recess , if laid in ground at a depth of 500mm below ground including excavation, backfilling, terminating with nut, bolt Spring, washer etc. as reuired. (Jointing shall be done by over lapping and with 2 sets of GI nut bolt & spring washer spaced at 50mm)

Supply and fixing cast iron Butterfly valve of the following sizecomplete with bolts, nuts, washers and neoprene gaskets as per specifications.

100 mm dia

80 mm dia

65 mm dia

Supply, installation, testing and commissioning of Dual Plate wafer type non return valve of rating PN 1.6 with CI body & SS plated of following sizes complete with rubber gasket, GI bolts, nuts, washers etc as required.

100 mm dia

80 mm dia

65 mm dia

Supply and fixing cast iron Y type strainer of the following sizecomplete with bolts, nuts, washers and neoprene gaskets as per specifications.

80 mm dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :

50 mm dia

40 mm dia

32 mm dia

25 mm dia

Supply and laying MS ERW black pipes as per relevant IS 1239/3589 marked including all accessories such as screwed/welded flanges, tees, reducers etc. conforming to IS standards complete including painting, welding, jointing and neoprene gaskets, nuts, bolts etc. as required.

100 mm dia pipes and fittings complete with anti corrosive, wrapping and coating of the pipes as per IS:10211 in all kinds of soil at a depth 1.5 m including excavation and refilling the trench all complete. (for Header)

80 mm dia pipes and fittings complete with anti corrosive, wrapping and coating of the pipes as per IS:10211 in all kinds of soil at a depth1.5 m including excavation and refilling the trench all complete. (For Suction & delivery pipe of pump)

65 mm dia pipes and fittings complete with anti corrosive, wrapping and coating of the pipes as per IS:10211 in all kinds of soil at a depth1.5 m including excavation and refilling the trench all complete. (For Suction & delivery pipe of pump)

Supply and fixing stainless steel Single headed external yard hydrant valves with instantaneous stainless steel couplings of 65mm dia. With cast iron wheel ISI marked conforming to IS 5290 (Type-A) 44 Providing stainless steel cap long fungus resistant

Supply and fixing 65 mm dia standard stainless steel short Branch Pipe as per IS 903 with 20 mm nozzle complete with fixing clamps.

Supply and fixing first aid hose reel full swinging type with 30 m length x 20 mm dia rubber lined pipe with ABS plastic shut off nozzle of 6 mm dia. The hose reel shall conform to IS requirements. Rate shall include 25 mm dia pipe connection from riser to hose reel including flexible pipe, sockets, nipples, elbows and 25 mm ball valve

Supply & fixing M.S Hose cabinet with powder coating of postal red color (of size 750MMx600MMx450MM) made of 14 G M.S.sheet with 6mm thick glazed glass doors i/c necessary locking arrangement suitable to accommodate external hydrant with butterfly valve , 2nos 15m long hoses and one no. branch pipe complete as per direction of Engineer incharge.

Supply and fixing Four Way Fire Brigade Inlet to Hydrant outside the Building (Butterfly valve and non return valve to be paid seprately) complete in all respects :

150mm dia.

Supply and fixing suction coupling for fire brigade drawl of water from tank with 150 mm dia MS(Heavy class) pipe and foot valve (Pipemax 24 M long)

Supply and installing cylindrical type air vessel of 300mm dia,1.5m high fabricated out of 8mm thick MS plate suitable for 7kg/sqcm.working pressure complete with 25mm gunmetal air release valve,safety valve, pressure gauge etc as required. The air vessel shall be continuous welded construction and painted with two coats of Postalred enamel paint outside over a coat of primer and Epoxy paint inside.

Providing & Fixing Fire Man axe as required with Test Certificate of 20000 volts.

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories :

Pendent Sprinkler

Upright Sprinkler

Horizontal side wall sprinkler

FIRE ALARM AND DETECTION SYSTEM (ADDRESSABLE TYPE)

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required

Supplying, installation, testing & commissioning response indicator on surface/recess MS box having two LEDs metallic cover complete with all connections etc. as required.

Supplying, installation, testing & commissioning of manual call boxes of MS construction in surface/recess with stainless steel chain & hammer assembly complete with glass and push button etc. as required.

Supplying, installation, testing & commissioning fire alarm sounder with facility to make announcement, mounted in M.S. box (16 SWG) with hinged cover plate & suitable for operation with amplifier i/c line matching transformer etc. complete as required

Supplying, installation, testing & commissioning of fault isolator complete with base as required

Supplying, installation, testing & commissioning of fire fighter telephone handset complete as required.

Supplying, installation, testing & commissioning of fire fighter phone jack complete as required.

Supplying, installation, testing & commissioning of addressable fire control module complete as required

Supplying, installation, testing & commissioning response indicator on surface/recess MS box having two LEDs metallic cover complete with all connections etc. as required.

Supply of 2c x 1.5 sq.mm Fire Survival Circuit Integrity Armoured Cable 600/1000 Volt rated with class-2 Copper conductor having cross linkable Low Smoke Zero Halogen insulation as per BS EN50363 and Low Smoke Zero Halogen (LSZH) inner & outer sheath. The cable should meet fire performance circuit integrity test as per BS EN50200 PH-120 & BS6387 CWZ (950 Deg. C for 3 hours). The cable should be LPCB certified to BS EN50200 (PH-120 & BS6387 CWZ. Outer sheath should be in Red colour having ANTI-RODENT LSZH properties.

Supplying, drawing, Installation, Testing and commissioning of Cat6A UTP 4 pair, 23 AWG solid copper cable in existing conduit/ on surface, U/FTP, LSZH, Non-Plenum, Horizontal (solid) Cable suitable for high speed data networking application supporting upto 10Gbps over a 100 meter channel. The 4 Unshielded Twisted Pairs (UTP) cable with color coded insulation for easy indentification should have FLAME PROPERTIES i.e. Flammability Test - IEC 60332-1, Smoke Density - IEC 61034, LSZH standards compliance: ANSI/TIA- 568 C.2, ISO/IEC 11801, IEEE 802.3an, RoHS. Delay Skew should be < 45NS. The outer Cable Diameter should be 7.5 + 2 mm. Cable should have been tested and verified by UL/ ETL.

1 run of cable

2 run of cable

3 run of cable

4 Run of cable

FIRE ALARM SYSTEM

The Panel Should have Min 24 Zone Controller expandable upto 144 zones with seamless integration facility with main fire alarm panel for voice evacuation complete as required.

Voice message priority according to risk analysis and emergency response plan

Each loop of fire alarm panel shall have 10-15% spare addressable units.

4 Loops Panel With Integrated Digital Voice Evacuation system. (For Upto 240+ Addressable devices per Loop) with Network Card. The Panel Should have 25/70 VRMS amplifier complete as required.

Supply, Installation, Testing & Commissioning of the Output Module controls speakers & Notification Appliances. The module have a panel controlled LED indicator. The LED flashes during normal operation and stays ON steadily when the device is in alarm condition. Supports group activation capability for fast reaction time. Can handle Class A or Class B device wiring. No external EOL required for class A operation. The Module shall be UL Listed & FM Approved.

Supply, Installation, Testing & Commissioning of Fire Panel Supervised Voice Evacuation Ceiling/Wall Mounted Fire Panel Supervised Voice Evacuation Speaker with 25 & 70 volt line matching transformers and include output power taps of 1⁄4, 1⁄2, 1 and 2 watt(s). High dBA output (over 90 dBA at 10 feet @ 2 watts) with moulded terminal block connection & equipped with a ground wire and frequency response of 400 to 4000Hz for Voice Evacuation with suitable rating amplifiers with Fire alarm panel including. Moisture resistant & Fire retardant cone material. The Speaker shall be UL/ULC Listed. Make-Advanced/Apollo/Mircom/Secutron/Honeywell-Gamewell.

CHAPTER - VII : PUBLIC ADDRESS SYSTEM

Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with USB, MP4 player (including 6 zone button paging station) with seamless integration facility with main fire alarm panel for voice evacuation complete as required.

Supplying, installation, testing & commissioning of 1.5/3/6W ceiling speaker complete as required.

Supplying, installation, testing & commissioning of digital audio amplifier 75 Watt, 25V rms operating at 240 Volt AC Supply complete as required.

Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required.

speaker cable Single pair, 2-core, 1.5 sqmm

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

CHAPTER - VIII : IP BASED EPABX SYSTEM

Supply, installation, testing and Commissioning of IP based voice communication system with 04 Port Voicemail, 04 Port FXS, 04 Port FXO, 1 PRI Trunk lines (30 Channels) Circuit with CLIP Facility, min 100 IP users License with provision for further additions, 100 analog users, 01 Number IP based Operator Console, 100 Party Conference, Speed Dial, Music on Hold, Internal/ External ring difference, Call Barring, Call Pickup, Reducdant server in active -Active mode and as per technical specification including supporting accessories etc complete as required.

Supply, Installation, Testing & Commissioning of Type 1 IP Phone having 2 VoIP account, 120 x40 DOT matrix screen with backlight, Full HD duplex speaker phone, IPV6, Gigabit Etherent, PoE etc. complete as required.

CHAPTER - IX : AUDIO VISUAL SYSTEM

Supply, installation, testing and commissioning of 65" 350 nits Brightness, Smart Android OS, 4K UHD Resolution, 16*7, Screen Mirroring through Airplay/Chromecast, Direct LED, 16 Gb storage, Wi-Fi, 178 Degree Viewing Angle, Landscape/Portrait/Tilt Installation, IP/RS232C Control, 10W+10W Speakers, HDMI 2.1 (3), USB (2), 1200:1 Contrast Ratio. 4K Processor X1, 4K X-Reality PRO, Motionflow XR, HDR10/HLG

Supply, installation, testing and commissioning of 55" 350 nits Brightness, Smart Android OS, 4K UHD Resolution, 16*7, Screen Mirroring through Airplay/Chromecast, Direct LED, 16 Gb storage, Wi-Fi, 178 Degree Viewing Angle, Landscape/Portrait/Tilt Installation, IP/RS232C Control, 10W+10W Speakers, HDMI 2.1 (3), USB (2), 1200:1 Contrast Ratio. 4K Processor X1, 4K X-Reality PRO, Motionflow XR, HDR10/HLG

Supply, installation, testing and commissioning of Mounting Arrangement for above Displays

Supply, installation, testing and commissioning ofCentral Conference Engine with recording capabilities shall have 4 or more Conference Ports shall have Integrated dynamics processor with programmable threshold ratio attack and release of noise gate AGC and limiter functions shall have USB port for expandable memory to record longer meetings (volumes up to 500 GB) shall have ON/OFF PowerSystem etc 48KHZ audio processing inbuilt equalization feature. Feature to perform centralized equalization. Web Server with User-friendly Interface (License based) shall have 1 x Balanced XLR audio input 1 x Balanced XLR audio output 2 x Unbalanced audio inputs 2 x Unbalanced audio outputs.Audio Routing Network Monitoring built-in Diagnostics application and camera control Loop cabling for redundancy in case of failure of unit, optional to configure as master and slave. It shall have flexibility to attach wireless conference units as well if required in future. Supports interpretation with a default of 2 languages + floor (can be extended to 63 + floor ) license based for future expansion, should have capability to perform look at me function for cameras over IP and standard RS-232 protocols. Control Port Ethernet should be 19" Rack Mountable. should have provision for master slave connectivity for redundancy should have inbuilt zoning feature allowing to configure individual audio output zones. should be BIS certified, BIS certificate to be submitted by the bidder Certification: CE etc complete with standard accessories as required. Approved makes: Brahler/Bronx/Televic

Supply, installation, testing and commissioning of table top chairman unit with chairman priority, Compact & attractive design, Excellent speech intelligibility with built-in accoustic feedback supression, Built-in volume control for headphones, headphone sockets, Built‑in loudspeaker, Loudspeaker volume is set centrally at the control unit for all delegate units level using knob, Encryption ensures that information within the system remains confidential, To prevent acoustic feedback, Systems can be configured in either daisy chain or ring topology, the built-in loudspeaker is automatically muted when the microphone is on, o 3.5 mm (0.14 in) stereo headphone sockets, Built‑in volume control for headphones, On-board support for automatic HD camera control, capacitanceSensitivity: -46 dBV /Pa , Headphone load: 16Ω, stereoInput impedance: 2kΩ SNR: 69dB, Frequency response: 18 ~ 18000Hz, should have two RJ45 connectors for loop in loop out connectivity or star connectivity, should have 48K full digital audio processing, should be supplied with low profile microphone of exceptional sound quality designed to give the user the possibility to view the meeting and be seen by other participants, Low profile microphone with Highly directional polar pattern, Cardiod Comm Shield Technology guards against interference from Cellular RF devices and digital bodypack transmitters Bidder should provide bid specific OEM authorization etc all complete

Supply, installation, testing and commissioning of table top delegate unit with Compact, attractive design, Excellent speech intelligibility with built-in accoustic feedback supression, Built-in volume control for headphones, headphone sockets, Built‑in loudspeaker, Loudspeaker volume is set centrally at the control unit for all delegate units level using knob, Encryption ensures that information within the system remains confidential, To prevent acoustic feedback, Systems can be configured in either daisy chain or ring topology, the built-in loudspeaker is automatically muted when the microphone is on, o 3.5 mm (0.14 in) stereo headphone sockets, Built‑in volume control for headphones, On-board support for automatic HD camera control, capacitanceSensitivity: -46 dBV /Pa, stereoInput impedance: 2kΩ SNR: 70dB, Frequency response: 18 ~ 18000Hz, should have two RJ45 connectors for loop in loop out connectivity or star connectivity, should have 48K full digital audio processing, should be supplied with low profile microphone of exceptional sound quality designed to give the user the possibility to view the meeting and be seen by other participants, Low profile microphone with Highly directional polar pattern, Cardiod Comm Shield Technology guards against interference from Cellular RF devices and digital bodypack transmitters.Bidder should provide bid specific OEM authorization etc all complete Approved makes: Televic/Bronx/Brahler

Supply, installation, testing and commissioning of low profile shot gun type microphone Features a 6-8.5 inches, 100-degree pickup area, narrower than a supercardioid or cardioid Frequency Response 125 to 15,000 Hz, Dynamic Range 90 dB SPL, Signal‐to‐Noise Ratio 68 dB, Sensitivity (open circuit voltage, @ 1 kHz, typical) –33 dBV/Pa (22 mV) . Approved makes: Televic/Bronx/Brahler

Supply, installation, testing and commissioning of Digital Signal Processor, shall offer advanced audio processing capabilities for various applications. The DSP shall provide enhanced control and management of audio signals. The DSP shall include a minimum of 8 Mic/Line inputs and 8 Line outputs, allowing for flexible audio routing and connectivity. Each microphone input shall support phantom power. The DSP shall feature a minimum of 8 or more AEC channels. This enables effective echo cancellation and improved audio quality, particularly in conferencing or telecommunication applications. To facilitate network audio integration, the DSP shall support a minimum of Dante channels and provide compatibility, network audio channels via Dante/AES67 or a similar protocol. This ensures seamless integration with networked audio systems and simplifies audio routing. The DSP will incorporate high-quality 24-bit A/D-D/A converters or better, ensuring accurate audio signal conversion. It shall operate at a sample rate of 48 kHz or better, RS-232 control, delivering high-fidelity audio reproduction. The input frequency response will be 20 Hz to 20 kHz or better, and the input dynamic range >94dB, providing excellent audio performance. should have USB port for USB based audio integration enabling 8x8 routing for USB audio through matrix, should be compatible with application based video conferencing applications. The supply of the DSP will include all necessary components and accessories for installation and operation.Approved makes: Serenix/TWaudio/Biamp

Supply, installation, testing and commissioning of ceiling speaker, featuring a 2-way open-back, bass reflex enclosure with polypropylene cone woofer and tweeter, butyl rubber surround, and Kapton voice coil former for high durability and sound quality. Engineered with a high-temperature voice coil and aluminium coupling ring for low distortion and extended high-frequency response. Rated for 7.5W/15W/30W/60W at 100V, 3.75W/7.5W/15W/30W/60W at 70V, and a 30W RMS power output, it supports line inputs at 100V, 70V, or 8Ω. The speaker unit includes a 6.5" woofer and 0.98" tweeter with a 2.5kHz crossover, and delivers a wide 150° conical dispersion for uniform audio coverage. Sensitivity is rated at 88.5dB (1W/1m) with a maximum SPL of 107dB, and frequency response ranges from 50Hz-20kHz (±3dB). Constructed with an ABS enclosure, removable locking 4-pin connectors, metal grille, and metal back can in white, it supports flush-mount in-ceiling installation. Ideal for background music and speech in schools, restaurants, hotels, train stations, and airports, this high-power output speaker is suited for large-scale PA system installations. Unit dimensions: 203mm diameter x 145mm height; cutout size: 170mm; weight: 2.1kg. Supplied in packaging of 8 units (540x500x420mm). Program power handling: 125W at 8Ω. Approved makes: Serenix/TWaudio/Biamp

Supply, installation, testing and commissioning of Class D mixer amplifier with power output 250W, designed for professional conference and public address systems. Features include four microphone inputs, three line inputs, one AUX output, and individual gain controls for each channel, plus treble and bass tone adjustment. Supports 70V, 100V, and low-impedance (4–16Ω) speaker outputs. Enhanced protection circuitry against short-circuit, overload, and high temperature. Equipped with side heat vents and an automatic speed-adjusting fan. Prioritised MIC1 and EMC muting. USB playback (up to 16GB), balanced 3-pin XLR mic inputs, and robust steel chassis. Powered by 110V/60Hz or 230V/50Hz mains. Ideal for multi-zone audio installations and conference environments. Makes: Serenix/Biamp/TWaudio

VIDEO CONFERENCE COMPATIBLE FOR CLOUD BASED CONFERENCE

Supply, installation, testing and commissioning of Poly Studio E60 Smart Camera 4K MPTZ with 12x Optical Zoom, Camera range 32 feet Group framing; Presenter tracking; Poly DirectorAI

Supply, installation, testing and commissioning of Poly Studio E60 Power Accessory

Supply, installation, testing and commissioning of 1 Year Partner Poly+ Poly Studio E60 Smart Camera 4K MPTZ with 12x Optical Zoom

Supply, installation, testing and commissioning of Poly Trio C60 IP Conference Phone and PoE-enabled No DECT, Three MEMS microphones for 360 degree mic pick up, 6.1 m/20 ft microphone pickup range

Supply, installation, testing and commissioning of Poly Trio C60 Expansion Microphones

Supply, installation, testing and commissioning of Poly Trio USB-A to Micro USB Cable (1.2M)

Supply, installation, testing and commissioning of Poly Trio C60 Power Supply with Power Cord and CAT-5

Supply, installation, testing and commissioning of 1yr Partner Poly+ Trio C60

Supply, installation, testing and commissioning of HDMI Cable 5 mtr

Supply, installation, testing and commissioning of Video Streamer/Recorder, High–performance, real–time HD video/audio over standard 100/1000Mb network, AVC Support — H.264/MPEG–4 & AAC codecs, Streaming Support — Unicast or Multicast through RTSP (Real Time Streaming Protocol), etc.

Supply, installation, testing and commissioning of ideo Encoder, High–performance, real–time 4K60 4:2:0 video/audio/RS–232/IR/USB over standard 1G network, Supports HDCP 2.2, Scalable enterprise grade one to many/many to many/video wall/KVM–over IP media distribution, etc

Supply, installation, testing and commissioning of Cable Cubby with Slow Motion Flip- Open Cover and Multi Format Cables, with the Cover of Desktop Socket which is made of Aluminium alloy finishing , design for perfect integration into the office Furniture, with Default Connectivity; 2 x Universal Power, 1 x USB-A Charger, 1 x USB - C Mobile Charger, 6 pass through holes Makes: Extron/Aktan/Crestron

Supply, installation, testing and commissioning of 4x4 HDMI Switcher with audio deembedding

Supply, installation, testing and commissioning of Transmitter and Receiver set for 70 Mtr

Supply, installation, testing and commissioning of 2 Mtr HDMI Cable

Supply, installation, testing and commissioning of 5 Mtr HDMI Cable

Supply, installation, testing and commissioning of Speaker Cable

Supply, installation, testing and commissioning of 12U Equipment Rack

Supply, installation, testing and commissioning of CAT-6 Cable with SSTP RJ45 Connectors

CHAPTER- X: ROAD / HARDSTANDING

Banking excavated earth by mechanical / manual means in layers not exceeding 20 cm in depth, breaking clods, watering, rolling each layer with ½ tonne roller, or wooden or steel rammers, and rolling every 3rd and top-most layer with power roller of minimum 8 tonnes and dressing up, in embankments for roads, flood banks, marginal banks, and guide banks etc., lead upto 50 m and for all lift :

All kinds of soil

Preparation and consolidation of subgrade with power road roller of 8-12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and comsolidating with road roller including making good the undulations etc and re-rolling the subgrade and disposal of surplus earth lead upto 50 metres.

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge.

With material conforming to Grade-II (size range 53 mm to 0.075 mm) having CBR Value-25

Construction of dry lean cement concrete sub base over a prepared sub-grade with coarse and fine aggregate conforming to IS:383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per specifications, cement content not to be less than 150 Kg/cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, for all leads & lifts, laid with a mechanical paver, compacting with 8-10 tonne vibratory roller, finishing and curing etc. complete as per direction of Engineerin-charge.

Providing and fixing polythene sheet of 125 micron thickness (separation member) over the levelled surface as specified in the drawings and as directed by Engineer-in-Charge etc., all complete.

Providing and laying design mix cement concrete of M-30 grade, in roads/ taxi tracks/ runways, using cement content as per design mix, using coarse sand and graded stone aggregate of 40 mm nominal size in appropriate proportions as per approved & specified design criteria, providing dowel bars with sleeve/ tie bars wherever required, laying at site, spreading and compacting mechanically by using needle and surface vibrators, levelling to required slope/ camber, finishing with required texture, including steel form work with sturdy M.S. channel sections, curing, making provision for contraction/ expansion, construction & longitudinal joints (10 mm wide x 50 mm deep) by groove cutting machine, providing and filling joints with approved joint filler and sealants, complete all as per direction of Engineerin- charge (Item of joint fillers, sealants, dowel bars with sleeve/ tie bars to be paid separately).

Note:- Cement content considered in M-30 is @ 340 kg/cum. Excess/ less cement used as per design mix is payable/ recoverable separately.

Cement concrete prepared with batch mixing machine

Dry stone pitching 22.5cm thick including supply of stones and preparing surface complete

Providing and fixing pre-moulded joint filler in expansion joints of RCC roads / CC pavements after making the joints dust free with high pressure air jet cleaners, all complete as per direction of the Engineer-in-Charge. (Pre-moulded joint fillers shall be made of bitumen hot sealing compound impregnated fibre board having impregnation more than 35%, conforming to IS:1838 for fibre board and IS: 1834 for hot sealing bitumen compound grade A.)

Providing and filling in position rubberized bitumen hot sealing compound for sealing of expansion joints in roads / pavements all complete as per direction of the Engineer-in-Charge.

Providing and filling in position rubberized bitumen hot sealing compound for sealing of expansion joints in roads / pavements all complete as per direction of the Engineer-in-Charge

Providing and placing PVC Pipe/Sleeve (40mm dia) on road expansion around dowl bars as per drawing and approved by Engineer-in-charge.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.

Mild steel and Medium Tensile steel bars

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Making bell mouth opening/ entrance of size 100x50x50 cm for drainage pipe under footpath, including providing cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) for shape of bell mouth, including plastering providing and fixing precast R.C.C./ S.F.R.C. slab including plastering with cement mortar 1:3 (1 cement : 3 fine sand) of 6 mm thickness on exposed surface of the slab & bell mouth including centring, huttering & neat cement punning inside the bell mouth etc. all complete.

Providing and fixing solar road studs (Model - RKSS01 of RK Security solution or equivalent) of size of 132x122x32mm having specifications: No of Led's - 6 LED's(3 Each side) Material - Aluminum Alloy and PC Installation Remarks - Gum Fix Water Proof Grade - >IP67 All complete, as per directions of Engineer-in-Charge.

Providing and fixing Plastic speed breakers (Model - RKPB50-1 of RK Security solution or equivalent) of size of 500x400x50mm all complete, as per directions of Engineer-in-Charge.

Providing and fixing Glow studs of size 100x20mm made of heavy duty body shall be mounted ASA (Acrylic styrene Acryloretrite) or HP (High impact polystyrene) or ABS having electronically welded micro-prismatic lens with abrasion resistant coating as approved by Engineer in charge. The glow stud shall support a load of 13635 kg tested in accordance with ASTM D4280. The slope of retro-reflective surface shall be 35(+/-) degrees to base. The reflective panels on both sides with at least 12cm of reflective area up each side. The luminance intensity should be as the specification and shall be tested as described in ASTM I:809 as recommended in BS :873. part 4:1973, The studs shall be fixed to the Road surface using the adhesive conforming to IS , as per provedure recommended by the manufacturer complete and as per direction of Engineer-in-charge.

Providing and applying 2.5mm thick road marking strips (retroreflective ) of specified shade/colour using hot thermoplastic material by fully /semi automatic thermoplastic paint application machine fitted with profile shoe, glass beads dispenser,propane tank heater and profile shoe heater driven by experienced operator on road surface including cost of material,labour, T&P. cleaning the road surface of all dirt,seals oil, grease and foreign material etc. complete as per direction of Engineer-in-charge and accordance with application specifications.

Providing and fixing post delineators made of ABS round body fitted with 2no 100mm dia high reflective reflectors and mounted on MS pipe of 65mm dia duly powder coated anti-rust and anti theft steel to be installed as per direction of Engineer-in-charge.

Providing and laying Non pressure NP-3 class(Medium duty) R.C.C pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2(1cement : 2 fine sand) including testing of joints etc. complete.

450mm dia RCC pipe

600mm dia RCC pipe

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :

150mm dia RCC pipe

250mm dia RCC pipe

Providing and laying 60 mm thick factory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

CHAPTER- XI : EXTERNAL WATER SUPPLY

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m :

All kinds of soil

Pipes, cables etc, not exceeding 80 mm dia.

Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia

Providing and laying S&S Centrifugally Cast (Spun)/Ductile Iron pipes confirming to is:8329:

100 mm dia Ductile Iron Class K-9 pipes

Providing push-on-joints to Centrifugally (Spun) Cast Iron pipes or Ductile Iron Pipes including testing of joints and including the cost of rubber gasket

100 mm dia pipes

Providing and fixing GI pipes complete with GI fittings and clamps, including cutting and making good the walls etc.

20mm dia nominal bore.

25mm dia nominal bore.

32mm dia nominal bore

40 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.

50 mm dia nominal bore

80 mm dia nominal bore

Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality :

50 mm dia nominal bore

80 mm dia nominal bore

Providing and filling sand of grading zone V or coarser grade, allround the G.I. pipes in external work :

50 mm dia nominal bore

80 mm dia nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :

25mm dia nominal bore

32 mm nominal bore.

50mm dia nominal bore

Making connection of G.I. Distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete

50 to 80 mm nominal bore

Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in reinforced cement concrete slab 1:1.5:3 mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size), including necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :

With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Supply & installation of Monoblock pumps set (3 HP) including starter panels and all kingds of fittings, suction & delivery, construction of pump foundation, all complete. (Make Cromption or equivalent)

CHAPTER-XII : EXTERNAL ELECTRIFICATION

11/0.433 KV, 3 Phase, 50 Hz Outdoor mounting TRANSFORMER-11/0.433 KV 1250KVA

Supply, installation, testing and commissioning of following capacity (continuous loading) 11/0.433 KV Delta/Star, step down, 3 Phase, 50 Hz, Dyn 11 vector group, Cast Resin / VPI (vacuum pressure impregnated) Dry Type, copper wound transformer (Electrolytic grade 99.9% pure copper, Core made of first grade Cold Rolled Grain Oriented (CRGO) Core grade MOH or better) AN (air natural) cooled transformer suitable for Outdoor applications with enclosure, On Load Tap Changer (OLTC) on HV side having AVS relay and Remote Tap Changer Control (RTCC) for automatic sensing of incoming voltage, automatic operation of OLTC and facility for remote/ manual operation of OLTC HV side in range of +5% to -15% in steps of 2.5%, insulation class F (minimum), suitable for environment conditions Class E-O-3, suitable for fire behavior class F1,climate class-C1, having cable end boxes on HV side suitable for 3x300 sqmm XLPE cable of 11 KV grade with necessary hardware, clamps, lugs etc. for termination on HV/MV etc. for all transformers, bus trunking arrangement on LV side complete with all accessories and safety provisions as per relevant IS Code ,The transformer shall be provided with standard fittings/accessories as per relevant IS and mentioned below, protection alarm/trip protection, 3 nos. of Polymeric Zinc Oxide surge Arrestors on HV Side. Winding Temperature scanner (Digital) with alarm/Trip contacts with RTD Sensors per LV winding and space for mounting differential protection CT's in LV chamber with neutral brought out separately including

supplying and laying of copper conductor multicore control cable from transformer to HT breaker/HT Panel for safety tripping, complete as confirming to IS-2026 Part-11, i/c supplying and grouting of suitable M.S. Channel with all accessories ,complete in all respects as required at site as per CPWD specifications. Design ambient condition : a) air temperature 50 deg C, b) Relative Humidity 90 % Max, c) Seismic Zone as per location of site, d) Altitude as per location/site. The transformer should have QR code which should contain drawing, test report OEM manual, Geo- Tag of manufacturing location, rating plate as per relevant IS Code etc. All testing shall as per relevant IS Code. Noise level Shall not exceed limits as per NEMA TR-1 with all accessories running measured as per IEC 551 / NEMA standard. The enclosure shall also have

Welded Door handle , Danger plate on HV and LV side doors, caution plate for tap links for HT doors, Door limit switch on both HV and LV side doors to be wired up to WTI box terminal for tripping the transformer in case door is opened with then closure transformer energized, Phase marking plates on HV and LV doors.

Fitting and Accessories : The following fittings shall be provided:- a) Two earthing terminals with the earthing symbol b) Rating and terminal marking plates; c) Thermometer pocket with cap; d) Lifting lugs for the complete transformer as well as for core and winding assembly; e) Bi-directional flat rollers (for transformers above 200 kVA); f) HV side neutral grounding strip (where one of the HV bushing terminal is connected to earth); g) Arcing horns or suitable rating lightning arrestors for HT side – 3 Nos. for transformers up to 200 kVA; h) Bird guard; i) Jacking pads (for transformer above 1 600 kVA); j) Name Rating & Diagram Plate. k) Monogram Plate. i) Additional neutral separately brought out on bushing for earthing.

630 KVA (losses at 50% loading < 2000watt, losses at 100% loading < 5855watt)

H.T. Cable

Supplying of following size of Al conductor, XLPE insulated armoured and over all PVC sheathed, 11 KV (UE) grade earthed cable as per technical specifications

3 core x 300Sq. mm

Supply & Laying of non skid Electro mat 1mtr wide and 2.5 mm thick 11KV grade IS 15652 as required including cutting to required length complete as per requirement of local electricity authorities.

Supply and fixing in position the approved “Shock Treatment Charts” written in English and Local Language. These charts shall be framed in teak wood frame and covered with glass.

Supply and fixing position the approved single line diagram for HT and LT panel framed in 1000 x 100 mm size glass frame and installed in main LT & HT Panel Room.

Supply of tool kit, first aid box with all accessories required for operation and maintainence for 415 volt & 11 kV equipment with 1 pair 11 kV rubber hand gloves of approved make.

HT Cable laying

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 kV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required.

Above 120 sq. mm and upto 400 sq. mm

supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 kV grade as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.

Above 120 sq. mm and upto 400 sq. mm

Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required.

250 mm dia

Supplying and making straight through cable jointing with heat shrinkable jointing kit complete with all accessories including ferrules suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required :

Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

Providing and fixing H.T. danger notice plate of 250 mm X 200 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

Automatic Power Factor Correction (APFC) System

Supply, Installation, testing and commissioning of Automatic Power Factor Correction (APFC) panel, indoor type floor mounted free standing totally enclosed, extendable, IP 42, of following capacity for 3 phase, 415 V + 10 %, 50 Hz AC System for Ambient temperature -5°C to +40°C, fabricated in compartmentalised designed made of CRCA sheet steel of 2.0mm thick for framework & covers, 3 mm thick for gland plate i/c cleaning & finishing complete with 9 tank process for powder coated of approved shade ( RAL 7032-Siemens gray or as approved by Engineer-in-Charge), having front section (switch gear and control accessories) and rear section capacitor and reactor, front and rear access, having suitable current carrying capacity, extensible TPN Aluminium alloy bus bar of high conductivity, DMC/SMC bus bar supports,bottom base channel of MS Section, fabrication shall be done in transportable section, entire panel shall have common copper earth bar of minimum size of 25mm x 5mm with 2 nos. earth studs, the earth terminals provided on the body of capacitor bank shall also be bonded to the main capacitor panel earth bus with 2 nos. 8 SWG or 6 SWG GI earth wires/ equivalent size of copper conductor cable, forced ventilation for maintaining temperature rise not more than 5°C from ambient, interconnections, connections with 14% detuned reactor and heavy duty 525 V ISI marked Impregnated MPP(Metalized Polypropylene) Capacitor (IS 13340 Part -1 & 2) APFC Panel shall be in compliance with IS :16636 & CPWD Specifications etc. as per below details.

(A) Incomers

Suitable capacity MCCB Microprocessor base with O/C, S/C,E/L release of TPN 50KA breaking capacity (Ics=Icu), ON, OFF,Trip, R, Y, B - LED Indicating Lamp set alongwith required Instruments and accessories with extended rotary handel and door interlocking arrangment. Current rating of the Incomer in ampere shall be APFC Panel rating in KVAR x 1.4 x 1.5 or Nearest higher standards rating.

(B) Instruments & Indications

3-Phase current sensing APFC microprocessor relay/controller , advance 8/12 stages (8 stages for capacity below 100 KVAR and 12 stages 100 KVAR & above) with Communication Ethernet/RS485/SNMP port open protocol for BMS integration as per approved by Engineering in charge and having display of Phase wise V, A, PF, Cos-Phi, Kw, KVA, KVAR, THD-V , THD-I, harmonics up to 31 level. 3 nos of dual core CT's accuracy class 1, 15VA at incomer of PCC Panel for APFC relay.

iii) Digital Multi function meter with LED Display for V, A, PF, KW, KVA, KVAR, THD-V & I, Frequency.

iv) Suitable rating control transformer shall be provided for control and indication circuit.

v) All components like control transformer, meter, relay and indicating lamp shall be protected by using suitable rating individual MCB's.

vi) Wiring of the control circuit shall be done by using 2.5 sq mm, FRLS/HFFR 1100 V grade, PVC insulated multi stranded copper control wire.

(C) Bus Bars

1.3 Amp per Sq.mm,TPN, Electrolytic grade Aluminium bus bar of capacity 1.25 times of incomer rating as per CPWD specification.

(D) Outgoings (APFC Section)

(i) Capacitor bank ratings & stages shall be as per the technical specifications sheet of NIT.

(ii) Capacitor will be MPP self healing type with discharge resistor, pressure release mechanism.

(iii) Since Capacitor Voltage is 525 Volts, thus higher KVAR has to be considered to get rated output at 415 Volts.

11 KV HT PANELS BOARD

11kV 3WAY Ring mains Unit (1 incomer 2 outgoings )

Design, Supply, Erection, Testing and Commissioning of 11 KV, 630A, 21KA for 3secs, SF6 insulated, Motorized, Outdoor, Right side extensible RMU , type tested in line with latest IEC standards. The RMU shall be suitable for operations at a height up to 1000 meters above sea level and at 40 degree ambient temperature without any derating. The switchgear and busbar shall all be contained in a stainless steel enclosure filled with SF6 at 0.3 bar (300 hPa) relative pressure. The RMU tank shall provide full insulation, making the switchgear insensitive to the environment with degrees of protection of IP67 . The switchgear operating mechanism shall have an IP2X protection and cable chamber shall have IP55. The outer enclosure should be IP 55 type tested, should be powder coated with pure polyester based paint , suitable for the site installation condition. Outer enclosure should be a integrated one and indoor RMU placed inside outdoor canopy is not acceptable. Accidental overpressure due to an internal arc is limited by the opening of the safety valve, at the bottom of the metal enclosure, away from the operator. An operator situated in front, lateral and rear (A-FLR 21kA – 1sec, downwards exhaust, for tank as well as cable compartment) of the RMU switchboard during an internal fault will not be exposed to the effects of arcing. Internal Arc Type Test Report for IAC AFLR 21 kA for 1 sec for both tank & cable box should have been for minimum 3 way / 3 Function RMU. Plug in type of extensibility must be provided and coupling busbar should not be exposed to air to avoid oxidation of busbars. Extension of cubicle should only require 450mm to handle and the gap between the coupled RMU’s must be within 10mm. All operations shall be from front of the RMU, including access to cable bushings. Cable bushings along the sides or the rear of the RMU are not acceptable. The outer enclosure of the RMU should be capable of withstanding the C5M climatic conditions as per ISO 12944-6 near to the sea shore within 500 M radius of sea shore. RMU Manufactured by OEM / OEM's authorized license partner are acceptable if they furnish the valid license under technology transfer.

Each of the above Ring Main Unit shall comprise of the followings:

Load Break Switch (LBS) as Incomer each comprising of the following:

11 KV, 630A, 21KA for 3sec Motorized Load break switch; with built in line side manual earth switch. Earthing should be completed within 2 operations only (i.e 1. Main switch - OFF, 2. Earth switch - ON). LBS shall have 3 positions, open or disconnected, closed and earthed, and will be constructed in such a way that interlocking prevents unauthorized operations. For earth switch, manual opening and closing will be driven by a fast-acting /snap action mechanism, independent of operator action. LBS and earth switch shall have a min of 1000 (M1) mechanical operations , and 5 nos closing operations at rated SC current. LBS should have 100 electrical operations at rated current

Position indicator through clear front mimic in line with IEC 62271-103

Live cable indicator with indications (Voltage Presence Indicator) at the front and three inlets provision to check the synchronization of phases. VPI should be of same make as that of RMU

Cable box with termination bushing suitable for upto 2 RUN 3Cx300 Sq mm, XLPE cable

Cable Boots suitable for actual cable size - 1R*3C*300 sq.mm.

Auxilary switch : LBS - 2 NO +2 NC, Earth switch - 1 NO + 1 NC

Fault passage indicator (FPI) with in-built Overcurrent, Short Circuit and earth fault indication (in (N-1) LBS). The FPI should be self-powered and should have internal lithium battery for external indication and setting of FPI in the absence of current. FPI should have 4 digit LCD display, ammeter feature and should be of same make as that of RMU

Mechanical operation counter

Suitable ratio CT 100/1 A, Class 0.5 for Metering, 2.5 VA

MFM EM 6400NG Class 0.5

2nos Vacuum circuit breaker (VCB) each comprising of the following:

11 KV, 630A, 21KA for 3sec Motorized VCB with spring assisted mechanism and series trip coil; with built in manual line side three position disconnector cum earth switch. Earthing should be completed within 2 operations only (i.e 1. Main switch - OFF, 2. Earth switch - ON). Vaccuum interrupter should be of same make as that of RMU. The circuit breakers shall have 2 positions: open or disconnected and closed. A separate and independent 3 position earthing switch and disconnector shall be fitted to open and earth the cables in such way that interlocks prevent all unauthorized operations. An independent mechanism shall be fitted for the 3 positions earthing switch and disconnector. Circit breaker shall have a min of 2000 mechanical and 2000 electrical operations at rated current and 50 nos of operations at rated short circuit current. Disconnector and earthswitch shall have a min of 1000 (M1) mechanical operations. The earthing switch shall be fitted with its own operating mechanism and manual closing shall be driven by a fast-acting mechanism, independent of operator action.

Position indicator through clear front mimic in line with IEC 62271-103

Self powered relay with O/C , E/F protection. Relay should have a front USB port for laptop interface , LCD display ,10 event records, 5 fault records with time stamp, min 2 setting group and keypad for setting parameters for the relay. Relay should be of same make as that of RMU

Suitable ratio CT 30/1 A, Class 10P5, 2.5VA for protection; Class 0.5 for Metering

MFM EM 6400NG Class 0.5

Live cable indicator with indications (Voltage Presence Indicator) at the front and three inlets provision to check the synchronization of phases.VPI should be of same make as that of RMU

Cable box with termination bushing suitable for upto 1 RUN 3Cx300 Sq mm, XLPE cable

Cable Boots suitable for actual cable size

Mechanical operation counter

Emergency trip push button

Air Insulated Bus Connected Unit comprising the following

Air Insulated enclosure with necessary bus connection via bushing. VT’s from the manufacturer and according to IS 3156 shall be accepted

11KV/rt3/110V/rt3; 25VA class 0.5. Single phase bus PT for metering

11KV/230V AC, 1KVA control transformer

FRTU as per the specifications + Modem for communication on IEC-104 protocol with DISCOM SCADA

Accessories

Antireflex operating handle

Battery 24V DC , 12Ah,

Battery charger (I/P-230V AC, O/P - 24V DC)

Manometer with remote contact per tank of RMU

MAIN LT PANEL-TTA TYPE

Supply,Installation, Testing and Commissioning of dust, damp and vermin proof IP- 5X free floor standing /wall mounted, Indoor type, form 3B/4A complied factory assembled in sheet steel enclosed modular construction, extendable from both side, fabricated out of CRCA grade d or equivalent sheet steel for load bearing member in 2mm thick and 1.6mm for non-load bearing members and doors with covers, 3mm thick for gland plates complete with 9 tank pre treatment process for powder coating with minimum 80 to 100 micron electro static powder coating coverage in approved shade of RAL 7032/7035 in elasto polymer type powder, complete with Aluminium bus bars designed for proper temperature rise withstand capacity, inter-connection with copper conductor wires / aluminium strips, neutral links, earth bus etc. including control wiring with 1.5sqmm. & 2.5sqmm. PVC insulated FRLS copper conductor S/C cable for voltage & current respectively, cable alleys, cable gland plates in two half for acb panels, etc. suitable for operation on 415 ±10% volts, 50 Hz AC 3 phase 4 wire system necessary metering protections & indications and mounted with the following switch gears etc. complete as required complying with IEC-61439 Part1&2 (TTA Type) .

(Each MCCB will have variable current setting for over current and short circuit, front extended lockable handle, pad lockable in off position, indication light for ON, shrouding on incomer side, termination shall be suitable for aluminium bus bars. All MCCBs shall be microprocessor based only otherwise as specified in the boq.

All Switchboards shall have provision for entry of cables from the top or bottom as required

All live accessible parts shall be shrouded and all equipment shall be finger touch proof. The Busbars shall be fully insulated with heat shrinkable sleeves and should withstand busbar temp. The busbar support insulators should be SMC. Padlocking isolating switches and load break switches lockable in OFF position. The panel shall meet criterias as per Client EHS guideline.

All kA ratings indicated shall be Ics = Icu = Icw values

Ics value should be 100%

GA drawings shall be got approved from Owners/Architects/ Consultants before fabrication.

Tube based Clean Agent Fire suppression system shall be taken for all panels as specified in the boq.

All Panel should be Form 4b (For ACB Compartment) &3b combination.

MAIN L.T PANEL- Ics=50KA

Incomers :- 5 Nos numbers (2 x 1000A, 4P EDO ACB from trafo + 2x 630A ACB From D.Gs.

Incomer from Traformers of 630 kVA

2 Nos. 1000A 4P EDO ACB with microprocessor based communicable release, over current with different time settings, short circuit with time delay & earth fault release with time delay, instantaneous current setting . Suitable links shall be provided for cable termination. ON/OFF/TRIP indication shall be wired through potential free contact up to terminal strip of breaker for hooking to BMS. Each incomer shall have following.

3 Nos. indicating lights for ACB on/ off/ trip position.

Phase Reversal relay for each Transformer incomer with indicator for trip and hooter for alarm.

1 no. 3 phase voltage monitoring relay cum phase sequence meter

1 No. APFC relay with matching cast resin CT's.

Incomers :- 2Nos numbers (1x630A, 4P EDO ACB from D.G Set)

Incomer from D.G Set of 320 kVA

2Nos. 630A 4P EDO ACB with microprocessor based communicable release, over current with different time settings, short circuit with time delay & earth fault release with time delay, instantaneous current setting . Suitable links shall be provided for cable termination. ON/OFF/TRIP indication shall be wired through potential free contact up to terminal strip of breaker for hooking to BMS. Each incomer shall have following.

3 Nos. indicating lights for ACB on/ off/ trip position.

1 No. reverse power relay with matching cast resin CTs for each D.G incomer

1 no. 3 phase voltage monitoring relay cum phase sequence meter

Bus Couplers

One number 1000A 4 pole EDO ACB microprocessor based over current, short circuit release type as bus coupler. Necessary contacts shall be wired upto terminal strip for breaker ON/OFF/TRIP, providing potential free contact ON/OFF/TRIP for status monitoring in BMS.

Bus Bar Section-I & II

Two set of TPN Aluminium bus bar rated for 1600A (after considering all necessary deratings) 3 phase 4wire, 50Hz. A minimum derating factor of 0.80 must be taken for calculation of bus bar sizes. The bus bar size after derating shall be equal to the ampere given in the BOQ. current density of bus-bars shall not be more than 0.8 Amps/sq.mm for Aluminium and earth bus size shall be suitable of system fault level.

Outgoings Bus Sections-1

2Nos. 630A 4P feeders each having one no.630A 4P MP based MCCB.Digital flush type class-1.0 accuracy multifunction meter showing V, A, PF, KVAR , KWH etc. along with current transformers of 300/5A ratio, 15 VA Class 1.0 metering.3 Nos. indicating lights for on/ off/ trip position & 1 Set of three phase R,Y,B indicating lamps along with 2A SP MCB backup protection.

3Nos. 315A 4P feeders each having one no.315A 4P MP based MCCB.Digital flush type class-1.0 accuracy multifunction meter showing V, A, PF, KVAR , KWH etc. along with current transformers of 300/5A ratio, 15 VA Class 1.0 metering.3 Nos. indicating lights for on/ off/ trip position & 1 Set of three phase R,Y,B indicating lamps along with 2A SP MCB backup protection.

5Nos. 200A 4P feeders each having one no.200A 4P MP based MCCB.Digital flush type class-1.0 accuracy multifunction meter showing V, A, PF, KVAR , KWH etc. along with current transformers of 200/5A ratio, 15 VA Class 1.0 metering.3 Nos. indicating lights for on/ off/ trip position & 1 Set of three phase R,Y,B indicating lamps along with 2A SP MCB backup protection.

1Nos. 160A 4P feeders each having one no.160A 4P MP based MCCB.Digital flush type class-1.0 accuracy multifunction meter showing V, A, PF, KVAR , KWH etc. along with current transformers of 160/5A ratio, 15 VA Class 1.0 metering.3 Nos. indicating lights for on/ off/ trip position & 1 Set of three phase R,Y,B indicating lamps along with 2A SP MCB backup protection.

1No. 63A 4P feeders each having one no.63A 4P MP based MCCB.Digital flush type class-1.0 accuracy multifunction meter showing V, A, PF, KVAR , KWH etc. along with current transformers of 60/5A ratio, 15 VA Class 1.0 metering.3 Nos. indicating lights for on/ off/ trip position & 1 Set of three phase R,Y,B indicating lamps along with 2A SP MCB backup protection.

Outgoings Bus Sections-2

2Nos. 630A 4P feeders each having one no.630A 4P MP based MCCB.Digital flush type class-1.0 accuracy multifunction meter showing V, A, PF, KVAR , KWH etc. along with current transformers of 300/5A ratio, 15 VA Class 1.0 metering.3 Nos. indicating lights for on/ off/ trip position & 1 Set of three phase R,Y,B indicating lamps along with 2A SP MCB backup protection.

3Nos. 315A 4P feeders each having one no.315A 4P MP based MCCB.Digital flush type class-1.0 accuracy multifunction meter showing V, A, PF, KVAR , KWH etc. along with current transformers of 300/5A ratio, 15 VA Class 1.0 metering.3 Nos. indicating lights for on/ off/ trip position & 1 Set of three phase R,Y,B indicating lamps along with 2A SP MCB backup protection.

5Nos. 200A 4P feeders each having one no.200A 4P MP based MCCB.Digital flush type class-1.0 accuracy multifunction meter showing V, A, PF, KVAR , KWH etc. along with current transformers of 200/5A ratio, 15 VA Class 1.0 metering.3 Nos. indicating lights for on/ off/ trip position & 1 Set of three phase R,Y,B indicating lamps along with 2A SP MCB backup protection.

1Nos. 160A 4P feeders each having one no.160A 4P MP based MCCB.Digital flush type class-1.0 accuracy multifunction meter showing V, A, PF, KVAR , KWH etc. along with current transformers of 160/5A ratio, 15 VA Class 1.0 metering.3 Nos. indicating lights for on/ off/ trip position & 1 Set of three phase R,Y,B indicating lamps along with 2A SP MCB backup protection.

1No. 63A 4P feeders each having one no.63A 4P MP based MCCB.Digital flush type class-1.0 accuracy multifunction meter showing V, A, PF, KVAR , KWH etc. along with current transformers of 60/5A ratio, 15 VA Class 1.0 metering.3 Nos. indicating lights for on/ off/ trip position & 1 Set of three phase R,Y,B indicating lamps along with 2A SP MCB backup protection.

Other items such as

PLC FOR INTERLOCKING & LOAD MANAGEMENT

Necessary electrical Interlocking through PLC/ advance contacts / contactors in MCCB/ ACB's (Incomers & Bus couplers) should be provided to ensure that only one supply is available at a time on each section of bus and to eliminate any possibility of accidentally approaching two supplies at one bus section as per single line diagram enclosed & as required.

1kVA online UPS with minimum 15 minutes backup built in battery for PLC system.

1 Lot of control wiring.

1 Set of designation plates

Tube based Clean Agent Fire suppression system for entire panel

MAIN L.T PANEL as describe above

CHAPTER-XIII : EXTERNAL LIGHTING

1 set of complete wiring

Supply,Installation, Testing and Commissioning of 35W LED Postop made up of aluminium pressure die-cast aluminum with UV protected polycarbonate diffuser in addition to a specific weathering resistance treatment. Big dai of 450mm for High Efficiency long life LED module with SMD LED package mounted on MCPCB. Lumen Efficacy of LED>115Lm/W and CRI >70. Powered by Built In electronic. LED driver 120-277V,Surge 4KV, Auto Restart, High Cut off ( >325 V), Auto Restart, THD < 10% at full load. System Lumen>4000 Lm, IP 66, IK 10, PF>0.95, Operating voltage range: 140 V - 270V, Average life L70B50: 50,000 hours. Luminaire manufacture shall provide LM79 report from NABL/UL accredited lab & LM80 report issued by LED manufacturer. Both the fixture and Driver should be of same make & must have separate BIS approval. including with the angle arragment for fixing and accesories as required. Similar to signify/philips cat. ref. no: BGP300 LED40 PSU PC IN

CHAPTER-XIV : lllUMINATED SIGNAGES & WATER COOLERS

Supply installation of Water Purification System with in built water coller & UV Purifications (RO+Chiller), with 60 Ltr. Storage tank made of stainless steel body operated on single phase 230V make and model as per approved by Engineer-in-charge.

Supply & intallation of IDEAL Purifier for room large coverage of upto 36m2 (380 Sqft), it purifies a standard room in just 10 minutes with a CADR of 300m3/h (Standard room size is 18ft by 12 ft with an 8ft ceilling height) 3-layer hepa filtration : Captures 99.97% of particles upto 0.003 microns (PM 0.003) - to protect from pollen, dust, pet dander, smog, or gasses and viruses. The phillips Nano Protect HEPA Filter can clean upto 2x more air than traditional HEPA H13 filtration COMPACT & PORTABLE DESIGN : The AC1711 Air purifiyer comes with a display panel on top, 3600 suction on the bottom and an air outlet on the top to ensure effective pure air circulation and ease of operation, making it the ideal room air purifier.

Supply, installation testing & commissioning of Pedstal Mouted 30 KW DC charging station for Vehcle charging facility brand & Model as approved by Engineer-in-charge.

CHAPTER-XV : EXTERNAL SEWERAGE

Excavating trenches by mechinical / manual means of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, for all depth, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All kind of soil

Pipes, cables etc, not exceeding 80mm dia

Pipes, cables etc, eceeding 80mm dia but not exceeding 300mm dia

Pipes, cables etc. exceeding 300 mm dia but not exceeding 600 mm

Excavating trenches of required width for pipes, cables, etc, including excavation for sockets, depth upto 1.5m, including getting out the excavated materials, returning the soil as required in layers not exceeding 20cm in depth, including consolidating each deposited layers by ramming, watering etc, stacking serviceable material for measurements and dispoal of unserviceable material as directed,within a lead of 50m: Ordinary Rock

Pipes, cable etc,not exceeding 80m dia

Pipes,cables etc, exceeding 80mm dia but not exceeding 300mm dia

Pipes, cables exceeding 300 mm dia but not exceeding 600 mm dia

Extra for excavating trenches for pipes, cables, etc. in ordinary/hard rock exceeding 1.5 m in depth but not exceeding 3 m. (Rate is over corresponding basic item for depth upto 1.5 metre). Ordinary rock :

Pipes, cables etc. exceeding 80 mm dia but not exceeding 300 mm dia

Pipes, cables exceeding 300 mm dia but not exceeding 600 mm dia

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :

150 mm dia. R.C.C. pipe

250mm dia RCC pipe

300mm dia RCC pipe

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design:

150mm dia RCC pipe

250mm dia RCC pipe

300mm dia RCC pipe

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating PCC block masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 180x150 mm size P type

With precast cement concrete solid blocks of 1:3:6 (1 cement :3 coarse sand: 6 graded stone aggregate 20mm nominal size)

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :

Inside size 90 x 80 cm and 45 cm deep including C.I. cover with frame (light duty) 455 x 610 mm internal dimensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg)

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra depth for circular type manhole 0.91m internal dia (at bottom) beyond 0.91 m to 1.67 m

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design :

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra for depth beyond 45 cm of brick masonry chamber :

For 455 x 610 mm size

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS: 10910 on 12 mm dia steel bar conforming to IS : 1786 having minimum cross section as 23 mm x 25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specification and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30 x 20 x 15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.

CHAPTER- XVI: STORM WATER DRAINAGE/TRENCHES FOR SERVICES

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan) ,including dressing of sides and ramming of bottoms, for all lifts, including ,getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50m.

All kind of soil

Excavtion work by mechanical means (Hydraulic excavator) /manual means in foundation trenches of drains (not exceeding 1.5m in, width or 10sqm on plan), including dressing of sides and ramming of bottoms, all lift, including getting out the excavated soil and disposal of surplus excavated soils as directed,within a lead of 50m.

Ordinary rock

Hard rock(blasting prohibited)

Centering and shuttering including strutting, propping etc, and removal of form for all heights:

Foundations, footings, bases of columns , etc, for mass concrete

Walls (any thickness ) including attached pilasteres, butteresses,plinth and string courses etc.

Suspended floors, roofs, landings, balconies and access platform

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering -All work up to plinth level:

1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources).

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing:

1:2:4 (1 Cement : 2 coarse sand (zone-Ill) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Ordinary Portland cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% times of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

All works upto plinth level

Concrete of M25 grade with minimum cement content of 330 kg /cum

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in :

Cement mortar 1 : 6 (1 cement: 6 coarse sand)

15 mm cement plaster on rough side of single or half brick wall of mix:

1:4 (1 cement: 4 coarse sand)

CHAPTER- XVII: BOUNDARY WALL

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

Any kind of soil

Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5m in width or 1 0 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50 m.

Ordinary rock

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 and for all lift.

Brick work with common burnt clay modular bricks of class designation 7.5 in foundation and plinth in:

Cement mortar 1 : 6 (1 cement: 6 coarse sand)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work upto plinth level

1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Centering and shuttering including strutting, propping etc. and removal of form for:

Foundations, footings, bases of columns etc. for mass concrete.

Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Columns, Pillars, Piers, Abutments, Posts and Struts

Steel reinforcement for R.C.C work including straightening, cutting , bending placing in position and binding all complete at all heights and locations.

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Ordinary Portland cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% times of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

All works upto plinth level

Concrete of M25 grade with minimum cement content of 330 kg /cum

All works above plinth level upto floor V level

Concrete of M25 grade with minimum cement content of 330 kg /cum

Add for using extra cement in the items of design mix over and above the specified cement content therein.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Washed stone grit plaster on exterior walls height upto 10 metre above ground level, in two layers, under layer 12 mm cement plaster 1:4 (1 cement : 4 coarse sand ), furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 2 Kg of cement per square metre, top layer 15 mm cement plaster 1:1/ 2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10 mm nominal size), in panels with groove all around as per approved pattern, including scrubbing and washing the top layer with brushes and water to expose the stone chippings ,complete as per specification and direction of Engineer-in-charge (payment for providing grooves shall be made separately).

Forming groove of uniform size in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer, including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications and direction of the Engineer-in-charge :

15 mm wide and 15 mm deep groove

CHAPTER - XVIII : ARBORICULTURE WORKS

Trees & Plantation Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately)

Holes 90 cm dia, and 90 cm deep

Supply and plantation of flowering or foilage or desired well gown Tree of 5" heigth sapling with disease /insect free, good foilage and stem girth and above 2-3 years old sapling. Staking the Tree sapling with bamboo staked of same height & 25mm thick. treated with anti termite solution and fixing in position, tie with stick at two suitable places. After plantation tree saplings & bamboo staking are to be maintained for a perioud of one month including replacing the capsualties with the same size and girth of tree sapling if any . List of trees are as following

Oelonix Regia / Peltophorum / Cessea Semia / Brush/ Jacaranda / Alestonia / Mimu sops Elengi / Graville nobusta / Poly Althfa Equivalent

Providing and stacking of Azadirachta indica ( Neem ) of height 120-130cm in big polybag of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Delonix regia (Gulmohar) of height 150-165 cm in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Ficus religiosa (Peepal) of height 150-165 cm in big poly bags of size 30 cm as per direction of the officer-in-charge.

Providing and stacking of Mangifera indica (Mango-grafted ) of height 60-75 cm. in big poly bag of size 25 cm as per direction of the officer-in-charge.

Shrubs Plantation Digging of Beds upto 60cm depth in all type of soil or pits 60cm deep including removal mild vegetation, debris etc. Refilling the pits with the excavated earth after antitermite treatment and mixture with cow dung organic manure in the ratio 3:1(3part of good earth :1 part of organic manure ) manure cost included (extra good earth if needed to be paid for separetely on actual measurement basic) Flooding the pit with water so that the earth & manure mixture settles down. Supply and plantation of approved shrub species(Like- TMC vari/callendera/cassia bifora euphorbia red/ Hibiscus/ Largestomea /Plumbago/ Hamelia/ Ficus Panda or equivalent)saping of good quality disease free, healthy 2-3 years old with well developed root system, in the centre of pit, with a clear ,minimum height of 1-1.5feet after the plantation,stacking the plant is essential with bamboo stick of same height treated with anti termite solution and fixing in position, tie with stick at, suitable place, shrubs if planted in beds shall be places @ 60cm. Watering it for 30days regularly as the minimum guarantee period including replacing the casualities with same size and age of plant if any.

In rows 5cm apart in both directions

With grass turf

Hedge Plantation Preparation of beds/ trench for hedging by excavation 60cm deepx45cm wide xRM in length in all type of soils, Refilling the excavated earth after breaking clods and mixing with sludge or organic manure in the ratio of 5:1 (five part of good earth and one part of organic manure) flooding with water filling with earth if necessary(good earth laid for separately on actual measurement basis after the reduction of 20% of its volume levelling and fine dressing for planting hedge sapling.

Ground Cover Preparation of beds/area/ground as per item no, 5(lawn) except ratio of manure should 5:1(five parts of good earth and one part of cow dung organic manure) including cost of manure ,soil if required to be paid separately and levelling , dressing to desired shape and levels, supply and plantation of approved ground cover species of sapling, about 1years old sapling with well gown, disease/insect free. After plantation sapling are to be maintained for a of one month including replacing the casualties if any

Creepers: Wadelia/Irysin/Altemanthra or equivalent in Poly Bags

Chlorophythytm/Ophiopogum/Ribben & black grass/Verbena/ Asp. Sprengeri/syngoniumI Golden Duranta/EquL 8" size.

Tradescantia /Dianella/Asparagus maril or equivalent

Ornamental Plants Supply and plantation of ornamental plants including digging of pits of size 50cm dia, And 60cm deep. Mixing of organic manure in the ratio of 3:1(three parts of good earth and one part of organic manure).Plantation of the approved varieties of Ornamental plant sapling, it should be well grown,disease/insect free. After plantation plant are to be maintened for a period of one month including replacing the casualties with same siz e& age of plant if any. Cycus Revoluta 3'ht/Cycus circinalls in 16'pots size 35-45 leaves fully developed

Fercarea 2' ht in 12" pots size

Phonix palms 2' ht. in 16" size

Ficus panda & benjamina/Golden duranta topiary 5-6" ht

Washingtonia palm 2"ht 14"Size

Euphorbia Millie in 10" pot size

Ficus starlight 3'-4;ht. busby & well developed

Golden bamboo 3-4" ht

Nolina 1.5-2'ht

Jumiperus 3'ht

Ficus benjamina Green busby 7-8" Ht.

Ficus Black Diamond 4'-5' Ht.Bishy

Bottle palm 7'ht. /Fox Tail Palm 6'/ Fish tail palm 5'

Budha Belly Bamboo 3'ht

Dracena Varietied Victoris 2"ht

Dracena SOI/Kedanath/Reffeca in 10" pot

Ixona 10' pot

Good Earth Supply and stacking of good earth suitable for plantation at site including royality and carriage (earth measured in stacks will be reduced by 20% for payment)

Filling mixture of earth and sludge or manure in the desired proportion in trenches, flooding with water and leveling (cost of supplying earth and sludge or manure and mixing excluded).

Supplying and stacking of well decayed cattle manure at site including royalty and carriage upto 5 k.m.lead complete (Cattle manure measured in stacks will reduced by 8% for Payment).

Supply and placing of indoor plants in 10" earthen pots in presantable form. Approved vertities : Area Palm/Aceroceria /1 Cratons/Money Plants /Aglonema or equivalent. As per direction of Engineer-in-charge.

Note:- Maintenance of Arboriculture will be one month after issued of completion certificate.

CHAPTER - XIX : DEMOLISHING OF EXISTING BUILDING / STRUCTURE

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.

In cement mortar

Dismantling tiled roofing with battens, boarding etc. complete including stacking of serviceable material and disposal of unserviceable material within 50 metres lead.

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead :

Of area 3 sq. metres and below

Of area beyond 3 sq. metres MS Railling

Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead.

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

Percentage BoQ

BoQ_Ver3.0

Name of the Bidder/ Bidding Firm / Company :

PRICE SCHEDULE (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only )

NUMBER #

CREDIT SCHEDULE FOR DEMOLISHED MATERIAL

Old Bricks

Scrap old steel MS Built-up Section

Credit for Hard Rock of CHAPTER-I (SH:1 EARTH WORK)

Credit for Hard Rock of CHAPTER- XVI: STORM WATER DRAINAGE/TRENCHES FOR SERVICES

Please Enable Macros to View BoQ information

eProcurement System Government of India Created By: Sheel Kamal Gupta Created Date/Time: 27-Oct-2025 12:53 PM Tender Title: Provision of Additional Multi Storied Building for Training Centre of CEPTAM at Metcalfe House, Delhi Tender ID: 2025_DRDO_878879_1

Total of BoQ 2 & BoQ 3

Total of BoQ 2

Total of BoQ 3

eProcurement System Government of India Created By: Sheel Kamal Gupta Created Date/Time: 27-Oct-2025 12:53 PM Tender Title: Provision of Additional Multi Storied Building for Training Centre of CEPTAM at Metcalfe House, Delhi Tender ID: 2025_DRDO_878879_1

Confoss Construction (GSTN-07AAAFC6514D1ZZ) BID ID -3295738

Aircon Technique Pvt Ltd (GSTN-07AAACA5596Q1Z0) BID ID -3295796

M/s Nand Kishore Anil Kumar (GSTN-07ADDPK2402J1ZX) BID ID -3297246

LEO AIR & POWER SOLUTION PVT LTD (GSTN-07AABCL1931F1ZW) BID ID -3297864

ARUN CONSTRUCTION (GSTN-NA) BID ID -3295227

eProcurement System Government of India Created By: Sheel Kamal Gupta Created Date/Time: 27-Oct-2025 12:53 PM Tender Title: Provision of Additional Multi Storied Building for Training Centre of CEPTAM at Metcalfe House, Delhi Tender ID: 2025_DRDO_878879_1

Confoss Construction (GSTN-07AAAFC6514D1ZZ) BID ID -3295738

Aircon Technique Pvt Ltd (GSTN-07AAACA5596Q1Z0) BID ID -3295796

M/s Nand Kishore Anil Kumar (GSTN-07ADDPK2402J1ZX) BID ID -3297246

LEO AIR & POWER SOLUTION PVT LTD (GSTN-07AABCL1931F1ZW) BID ID -3297864

ARUN CONSTRUCTION (GSTN-NA) BID ID -3295227

Confoss Construction (BID ID -3295738)

LEO AIR & POWER SOLUTION PVT LTD (BID ID -3297864)

M/s Nand Kishore Anil Kumar (BID ID -3297246)

Aircon Technique Pvt Ltd (BID ID -3295796)

LEO AIR & POWER SOLUTION PVT LTD (BID ID -3297864)

Confoss Construction (BID ID -3295738)

M/s Nand Kishore Anil Kumar (BID ID -3297246)

Aircon Technique Pvt Ltd (BID ID -3295796)

LEO AIR & POWER SOLUTION PVT LTD (BID ID -3297864)

Confoss Construction (BID ID -3295738)

M/s Nand Kishore Anil Kumar (BID ID -3297246)

Aircon Technique Pvt Ltd (BID ID -3295796)