Package No.558_1

Amount

1. COMMUNITY HALL (ASSAM TYPE) : Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of: 15.28.1 G.S. Sheet

Providing corrugated G.S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/vertical or curved surfaces), excluding the cost of purlins, rafters 0.63mm thick with zinc coating not less than 275 gm/m2

Providing ridges or hips of width 60cm overall width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8mm dia G.I. limpet and 0.63mm thick with zinc coating not less than 275 gm/m2

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges or required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately). Second class teak wood 30mm thick shutters

Providing and fixing plain multipurpose cement board (Hight pressure steam cured) with suitable screws for cement particle board in ceiling etc. complete (frame work to be paid separately). 12.26.1 6mm thick cement fiber board as per IS:14862

Distempering with 1st quality acrylic distemper (ready made) having VOC content less than 50 gm per ltr. Of approved manufacturer and of required shade and colour complete. As per manufacturer's specification. 13.108.1 One or more coats on old work

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement:3 coarse sand (zone-III) derived from natural sources: 6 graded stone aggregate 20mm nominal size derived from natural sources) over 75mm thick bed of dry brick.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using primer as per manufacturers specifications: 13.48.1 Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of special primer applied @ 0.75 ltr/10sqm

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joints with white cement and matching pigments etc., complete. 11.41.1 Size of Tile 500 x 500mm 11.41.2 Size of Tile 600 x 600mm

Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.75 ltr/10 sqm of approved brand and manfacture.

2. ELECTRICAL WORKS : Wiring for light point/fan point/Exhaust fan point/Call bell point with 1.5 sq mm FRLS PVC insulated copper Conductor single core cable in surface/recessed medium class PVC conduit with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq mm FRLS PVC insulated copper conductor single core cable etc, as required. 1.10.1 Group A

1.10.2 Group B

1.10.3 Group C

Wiring for circuit/submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/recessed medium class PVC conduit as required. 1.14.2 2x2.5 sq mm + 1x2.5 sq mm earth wire

1.14.3 2x4 sq mm + 1x4 sq mm earth wire

1.14.4 2x6 sq mm + 1x6 sq mm earth wire

Supplying and fixing following modular switch/socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 1.24.1 5/6 A switch

1.24.3 15/16 A switch

1.23.4 3 pin 5/6 A socket outlet

1.24.5 6 pin 15/16 A socket outlet

1.24.8 Bell push (Office RM)

Supplying and fixing two module steeped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing following size/modules GI box along with modular base & cover plate for modular switches in recess etc. as required. 1.27.2 3 module (100mm x 75mm)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/wooden block including connections etc. as required.

Supplying and fixing brass batten/angle holder including connection etc. as required.

Supplying and fixing call bell/buzzer suitable for single phase, 230V, complete as required.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (Upto 30cm) with 1.5 sq.mm FRLS PVC insulated, copper conductor, single core cable etc. as required.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. 1.50.1 Up to 450mm sweep

Wiring for group controlled (looped) light point/fan point/exhaust fan point/call bell point (without independent switch etc.) with 1.5sq.mm FRLS PVC insulated copper conductor single core cable in surface/recessed PVC conduit, and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. 1.55.1 Group-A

1.55.2 Group-B

Supplying and fixing following way, single pole and neutral, sheet steel, MCB Distribution board, 240 V on surface/recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar interconnections powder painted including earthing etc. as required (But without MCB/RCCB/Isolator). 2.3.3 6 way Double door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator). 2.4.1 4 way (4+12) Double door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 KA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as rquired. 2.10.1 Single pole

2.10.2 Double pole

Supplying and fixing following rating four pole 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 2.13.2 63A

Earthing with G.I. earth pipe 4.5 metre long, 40mm dia including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/coke and salt as required.

Supplying and laying 25mm x 5mm G.I. strip at 0.50 metre below ground as strip earth electrode, including connection/terminating with G.I. nut, bolt, spring washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm).

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.

Providing and fixing of lighting conductor finial, made of 25mm dia 300mm long, G.I. tube having single prong at top, with 85mm dia 6mm thick G.I. base plate including holes etc. complete as required.

Jointing copper/G.I. tape (with another copper/GI tape, base of the finial or any other metallic object) by riveting/nut bolting/sweating and soldering etc. as required.

Providing and fixing GI tape 20mm x 3mm thick on parapet or surface of wall for lightning conductor complete as required. (For horizontal run).

Providing and fixing GI tape 20mm x 3mm thick on parapet or surface of wall for lightning conductor complete as required. (For vertical run).

Providing and fixing testing joint, made of 20mm x 3mm thick GI strip, 125mm long, with 4 nos. of GI bolts, nuts, chuck nuts and spring washers etc. complete as required.

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protection covering and refilling the trench etc. as required. 7.1.1 Upto 35 sq.mm

Supply, installation, Testing and Commissioning of 1200mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30cm long down road 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85 Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS: 374-2019) THD less than 10% remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC supply, earthing etc. complete as required.

Supplying and fixing 415 V four Pole MCCB of Breaking capacity 36ka with fixed thermal and fixed magnatic/adjustable thermal and fixed magnatic setting in an enclosure and necessary connection. 160 Amp 3P MCCB

Enclosure for MCCB

Supplying and fixing double door vertical TPN Distribution board for MCCB incomer with IP-43 protection on angle iron frame on wall & mending good the damages to original finish incl. inter connection with suitable size of copper wire and neutral link & provision for earthing attachment. (Havells Make) 8 Way VTPN DB

Supplying and fixing 240/415 V MCB of Breaking capacity 10ka & C characteristics on din rail of existing DBs and necessary connection. 63A TP

Supplying and fixing 240/415 V MCB of Breaking capacity 10ka & C characteristics on din rail of existing DBs and necessary connection. 40A TP

Supplying of XLPE Al./Cu. Armoured cables as below: 4Cx16sq.mm. XLPE Al Arm. Multistranded Cable

Supplying of XLPE Al./Cu. Armoured cables as below: 3&1/2 core 35 sq.mm. XLPE Al Arm. Multistranded Cable

Supplying, Installation, Testing & Commissioning of following watts/type LED fitting with all accessories and lamps mounting on ceiling surface/false ceiling not less than 100 lumens/watt, Min-50000 burning hours, LM79 report, THD less than 20% including making suitable cutting on false ceiling (wherever required) connection with 1.5sq.mm. FRLS PVC insulated copper conductor single core FR type cable as required. 8.0 a. 20 Watt Tube Light.

9.0 b. 18 Watt Surface type Ceiling Light

10.0 C12 Watt LED Bulb

Exhaust Fan-250mm dia

Supply fitting and fixing of All-in-one integrated Solar street light 60W

Supply fitting and fixing of 1.5 H.P. Submerssible pump set (water filled Motor Crompton make).

Supply, installation, Testing and Commissioning of orgria Solar Photovoltaic Power Plant conforming to MNRE specification sasamended, consisting of Mono/Poly Crystallines silicon solar cells, net metering facility, necessary protections, earthing, mountedon Aluminiu/GI structure of suitable strength with following components complete as required:- a) Solar Photo voltaic Module of capacity 330W por above, manufactured in India, conforming to ISI 14286/IEC61215, IS/IEC617 30-Part-1, IS/IEC61730-Part-2. Solar Photo voltaic Module conversion efficiency shall not be less than 16.5% PV module susedin solar power plants/system must be warranted for their out put peak watt capacity, which should not be less than 90% attheend of 10 years and 80% attheend of 25 years. b) Power conditioning Unit (PCU) of 350-800 VDC in put voltage range and 400 VAC, three phase, 4 wire, 50Hz+/- 2.5Hz, out put voltage suitable to generate AC Power with efficiency not less than 97% total harmoic distortion less than 3% and suitable for ambient temperature from 0 to 50 degree C. The PCU shall adjust the voltage and frequency level to suit the Grid Voltage Frequency. C) Data Monitoring system complete with accessories. d) Fixing of Array junction box & Main junction box with IP65p rotection and termination arrangement for incoming and outgoing cable along with glands, lugsand other accessories etc. as required. e) Lighting and surge voltage protection.. Connections & Interconnections by supplying & finging required size XLPE insulated copper conductor 1.1 KV grade armoured power and control cable

DANIEL BRAHMA (BID ID -277192)

Kemendra Kr Brahma (BID ID -277280)