AMC of Staff quarter (Civil) 2020-21

Amount

Demolishing cement concrete 1:3:6 or richer mix manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.

Demolishing R.C.C. work manually / by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Demolishing brick work in cement mortar manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area 3 sq. metres and below

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead: Of area 3 sq. metres and below

Dismantling of 15 to 40 mm dia G.I. Pipe including stacking and diposing of dismantled pipes in IIP store yard, as per the direction of Engineer-in-Charge.

Dismantling of flushing cistern of any size including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead.

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

Disposal of building rubbish/malba/similar unserviceable,dismantled or waste materials by mechanical means,including loading,transporting,unloading to approved dumping ground within IIP campus or as approved by Engineer-in-charge,beyond 50 m lead,for all leads including all lift involved.

Dismantling W.C. Pan of all sazes including disposal of dismantled materials and malba all complete as per the direction of Engineer -in-charge.

Taking out existing wooden door shutter,repair by cutting,painting etc. And and refixing of repaired door shutters to existing door frame, including replacement of hinges with screws, 4 mm ply etc. as required,all complete as per the direction of the Engineer-in-charge.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. For Thermo-Mechanically Treated bars of grade Fe- 500 D or more.

Centering and shuttering including strutting, propping etc. and removal of form for : Shelves (Cast in situ)

Brick work with F.P.S. bricks of class designation 75 in foundation and plinth in Cement mortar 1:6 (1 cement : 6 coarse sand)

Half brick masonry with F.P.S. bricks of class designation 75 in superstructure above plinth level up to floor V level in Cement mortar 1:4 (1 cement :4 coarse sand)

Providing sal wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position :

Providing and fixing 30 mm thick second class teak wood glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes including black enamelled ISI marked M.S butt hinges with necessary screws.

Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters : For 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.

Providing and fixing 35mm thick second class teak wood wire gauze shutters using galvanised M.S. wire gauze of average width of aperture 1.4mm with wire of dia. 0.63 mm for doors, windows and clerestory windows including ISI marked bright finished or/and black enamelled M.S. butt hinges with necessary screws :

Providing and fixing 25 mm dia (heavy type) nickel plated M.S. pipe curtain rods with nickel plated brackets :

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. all complete. For fixed to steel windows by welding.

Providing and fixing fly proof galvanised M.S. wire gauze to windows and clerestory windows using galvanised M.S. wire gage with average width of aperture 1.4 mm in both directions with wire of dia. 0.63 mm. With 2nd class teak wood beading 62X19 mm.

Providing and fixing 250X16 mm ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete :

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete :

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete :

Providing 40mm thick with 20mm nominal size stone aggregate Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete.

Providing and fixing 40 mm wide and 4 mm thick glass strips in joints of terrazo/ cement concrete floors.

Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand) including pointing the joints with white cement and matching pigment etc., complete.

Providing and fixing on wall face un plasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.(i) Single socketed pipes.

75 mm diameter

110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.

Single tee with door 75x75x75 mm

Single tee with door 110x110x110 mm

Single tee without door 75x75x75 mm

Single tee without door 110x110x110 mm

75 mm bend 87.5°

110 mm bend 87.5°

Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer 3mm thick water proofing membrane, black finished reinforced with non-woven polyester matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 ltr/sqm. by the same membrane manufacture of density at 25°C, 0.87-0.89 kg/ltr and viscocity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane Torch and sealing all joints etc., and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 650/450N/5cm. Tear strength in longitudinal and transverse direction as 300/250N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane :

12 mm cement plaster of mix 1:6 (1 cement: 6 fine sand)

Distempering with 1st quality acrylic distemper (ready mix) having VOC content less than 50 gms/litre, of approved brand and manufacture of required shed and colour complete,as per manufacturer's specification.

New work (two or more coats) over and including priming coat with cement primer.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :

Two or more coats on new work

Providing and applying white cement based putty of average thickness 1 mm of approved brand and manufacturer over the plastered wall surface to prepare the surface even and smooth complete.

Applying priming coat : With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)

Repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq. meters and under including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50metres lead : With cement mortar 1:4 (1 cement : 4 fine sand)

Fixing chowkhats in existing opening including embedding chowkhats in floors or walls cutting masonry for holdfasts embedding hold fasts in cement concrete blocks with cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) painting two coats of approved wood preservative to sides of chowkhats and making good the damages to walls and floors as required complete including disposal of rubbish to the dumping ground within 50 meters lead :

Door chowkhats

Window chowkhats

Renewing glass panes and refixing existing wooden fillets: with Float glass panes of thickness 4 mm

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete

Distempering with 1st quality acrylic distemper (ready mix) having VOC content less than 50 gms/litre, of approved brand and manufacture of required shed and colour complete, as per manufacturer's specification.

one or more coats on old work

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :

One or more coats on old work.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require :

White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap.

Providing and fixing 610x460 mm bowl depth 200 mm Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required :

Providing and fixing white vitreous china water closet squatting pan (Indian type). For Orissa pattern W.C. pan of size 580x440 mm

Providing and fixing white vitreous china pedestal type (European type/ wash down type) water closet pan.

Providing and fixing 8 mm dia C.P. /S.S.jet with flexible tube upto 1 metre long with S.S triangular plate to European type W.C. Of quality and make as approved by Engineer-in-Charge.

Providing and fixing 10 litre capacity - White P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete.

Providing and fixing 32 mm dia P.V.C. waste flexible pipe for sink or wash basin including P.V.C. waste fittings complete.

Providing and fixing Rectangular shape of size 453x357mm mirror of superior glass (of approved quality) and with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :

Providing and fixing 15 mm nominal bore G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc.Internal work – Exposed on wall.

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.External work

20 mm dia. Nominal bore

50 mm dia. Nominal bore

Providing and fixing 15 mm nominal bore ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :

Providing and fixing 15 mm nominal bore and 45 cm length uplasticised PVC connection pipe with brass unions :

Providing and placing on terrace (at all floor levels) polyethylene circular water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank

Providing and fixing 15 mm nominal bore C.P. brass bib cock of approved quality conforming to IS:8931

Providing and fixing 15 mm nominal bore C.P. brass bib cock of approved quality conforming to IS:8931

Providing and fixing 15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931

Providing and fixing PTMT bib cock of approved quality and colour.

15mm nominal bore, 86 mm long. Weighing not less than 88 gms.

15 mm nominal bore, 122mm long. Weighing not less than 99 gms.

Providing and fixing 15 mm nominal bore, 86mm long Weighing not less than 88 gms.PTMT stop cock of approved quality and colour.

Providing and fixing 15mm nominal bore, 107mm long. Weighing not less than 110 gms PTMT pillar cock of approved quality and colour .

Providing and fixing 15 mm nominal bore, 105 mm long Weighing not less than 138 gms PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball.

Providing and fixing PTMT angle stop cock 15 mm nominal bore. Weighing not less than 85 gms.

Providing and fixing PTMT swivelling shower, 15mm nominal bore. Weighing not less than 40gms.

Labour supply in mandays

unskilled (Beldar/coolie)

Skilled / Mistri (Mason/Plumber/Painter etc as and when required by department.)

Proving and fixing size of stainless steel wash basin / sink jali as required of required size etc. all complete.

Cleaning of sewer line of all size dia including intermediate chamber etc. Complete as per the instruction of Engineer-in-Charge.

ROORKEE ASSOCIATES