CA NO CE CHZ AMB T 19 2021 22 ADDITION ALTERATION AND UPGRADATION OF OFFRS JCOS AND ORS MARRIED ACCN INCLUDING CONSTRUCTION OF GARRAGES AT AMBALA CANTT

Amount

Schedule 'A'Section-I (Building Works)

Lump sum price worked out by the Contractor for "Building Work" as listed in Sch 'A' Sec I

Schedule 'A'Section-II (Site Clearance And Earthwork)

Lump sum price worked out by the Contractor for "Site Clearance And Earthwork" as listed in Sch 'A' Sec II

Schedule 'A'Section-III (APPROACH PATH AND REPAIR/UPGRADATION OF EXISTING PATH WORKS)

Lump sum price worked out by the Contractor for "Approach path and repair/upgradation of existing path works" as listed in Sch 'A' Sec III

Schedule 'A'Section-IV (SECURITY WALL & SECURITY FENCING WORKS)

Lump sum price worked out by the Contractor for "Security Wall and Security Fencing Works" as listed in Sch 'A' Sec IV

Schedule 'A'Section-V (EXTERNAL WATER SUPPLY WORKS)

Lump sum price worked out by the Contractor for "External water supply works" as listed in Sch 'A' Sec V

Schedule 'A'Section-VI (EXTERNAL ELECTRIC SUPPLY WORKS)

Lump sum price worked out by the Contractor for "External electric supply works" as listed in Sch 'A' Sec VI

Schedule 'A'Section-VII ( DEMOLITION / DISMANTLING WORKS)

Lump sum price worked out by the Contractor for "Demolition/dismantlng works" as listed in Sch 'A' Sec VII

Schedule 'A'Section-IX(Misc Items of Works) Note : This schedule is not pre-priced by MES and the pre-priced rate indicated as "Rs 0.00" under Col. 5 siginifies this fact only.

ITEM NO. 1 : Cutting openings, through brick walls built in cement mortar for door, window and other openings or enlarging existing openings, converting window into door openings etc. or cutting out defective brick work for under- pinning, including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard-core, etc and rubbish not exc. 50 mtr from site complete all as specified and directed by Engineer-in-Charge.

ITEM NO. 2 : Taking down Cement plaster or cement lime plaster on brick or stone walls including raking out joints, hacking for key & scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge.

ITEM NO.3 : Demolition of cement concrete (reinforced) (reinforcement cut as required to facilitate demolition) as in roofs, floors (other than ground floors) beams, slabs, staircases, landing, chajjas and similar suspended work complete all as specified and directed by Engineer-in-Charge.

ITEM NO.4 : Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

ITEM NO.5 : Demolition of Cement concrete unreinforced as in Ground Floor and paving n. exc. 15cm thick (above or below G.L.) complete including disposal of unservicable rubbish outside Cantt area all as specified and directed by Engineer-in-Charge.

ITEM NO.6 : Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc of any description or thickness, laid, bedded and pointed in any mortar complete all as specified and directed by Engineer-in-Charge.

ITEM NO.7 : Taking down chowkhats or frames n.exc 1.5 sqm each (without taking off shutter from the frame) and removing from the site including dismantling brick work of hold fasts complete all as specified and directed by Engineer-in-Charge.

ITEM NO.8 : Taking down chowkhats or frames exc 1.5 sqm but n.exc 4 sqm each (without taking off shutter from the frame) and removing from the site including dismantling brick work of hold fasts etc complete all as specified and directed by Engineer-in-Charge.

ITEM NO.9 : Taking down shutters of any description n exc 1 Sqm each and removing from the site complete all as specified and directed by Engineer-in-Charge.

ITEM NO.10 : Taking down shutters of any description exc 1 Sqm and not exc 2 Sqm each and removing from the site complete all as specified and directed by Engineer-in-Charge.

ITEM NO.11 : Taking down of wooden door shutter of any description and refixing of shutter of area n.exc 1 Sqm in same opening after repair/easening etc complete all as specified and directed by Engineer-in-Charge.

ITEM NO.12 : Taking down of wooden door shutter of any description and refixing of shutter of area exc 1 Sqm and not exc 2 sqm in same opening after repair/easening etc complete all as specified and directed by Engineer-in-Charge.

ITEM NO.13 : Dismantling structural steel work including doors, gates but excluding framed truss etc,including erection and refixing of old framed steel work as in doors or gates of angle or other section with gusset plates, rails, braces, etc, complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and fixing complete all as specified and directed by Engineer-in-Charge.

ITEM NO.14 : Dismanting of stucturel steel work as in door chowkats, shutters guard bars and similar items but excluding framed truss complete all as specified and directed by Engineer-in-Charge.

ITEM NO.15 : Hacking out old broken glass (any thickness, size , quality or description) from wooden, glazed with putty or fixed with beads including clearing rebates for re-glassing, taking out beads, removing rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

ITEM NO.16 : Dismantling wooden boarding any description, fixed in any position with nails as in shelves of cup board and pelmets of any description complete all as specified and directed by Engineer-in-Charge.

ITEM NO.17 : Running welding in repairs to hinges of steel window/pressed steel door and steel ladder of various guard post /watch towers and making good for opening of doors/window shutters thickness of metal to be welded exc 6 mm but n exc 9 mm complete all as specified and directed by Engineer-in-Charge.

ITEM NO.18 : Taking down of Eaves gutter/rain water pipe( AC rain water pipe /SWG pipe line of any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fitting and accessories) complete all as specified and directed by Engineer-in-Charge.

ITEM NO.19 : Demolition and breaking up 150 mm bore drain pipes (salt glazed stone ware pipes) set in cement mortar complete all as specified and directed by Engineer-in-Charge.

ITEM NO.20 : Taking up or down steel tubing and connections of 15mm bore in pipe, including cleaning for re-fixing or removal from site to store complete all as specified and directed by Engineer-in-Charge.

ITEM NO.21 : Taking up or down steel tubing and connections of 20mm bore in pipe, including cleaning for re-fixing or removal from site to store complete all as specified and directed by Engineer-in-Charge.

ITEM NO.22 : Dismantling of cast iron or RCC drain pipes 100 mm bore jointed in cement mortar from floors/walls etc. and taking out of trenches if required complete all as specified and directed by Engineer-in-Charge.

ITEM NO.23 : Dismantling of cast iron or RCC drain pipes 75 mm bore jointed in cement mortar from floors/walls etc. and taking out of trenches if required complete all as specified and directed by Engineer-in-Charge.

ITEM NO.24 : Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed Conduit(TV/Tele Socket) etc., and making good, cutting not exc 10cm girth and complete all as specified and directed by Engineer-in-Charge.

ITEM NO.25 : Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position.(cleaning reparing etc measured separately) complete all as specified and directed by Engineer-in-Charge.

ITEM NO.26 : Demolition of brick work built in cement mortar incl all quions arches, pillar or any other description etc complete all as specified and directed by Engineer-in-Charge.

ITEM NO.27 Demolition of cement concrete (reinforced) of any description and in any position including cutting of rienforcement complete all as specified and directed by Engineer in Charge.

ITEM NO.28 : Dismantling of brick or terracing tiles of single layers on roofs incl cleaning of bricks/tiles and removal of unusable bricks/tiles and removal from site, complete all as specified and directed by Engineer-in-Charge.

ITEM NO.29 : Demolition of mud roof any thickness (whether full thickness removed or part thereof ) including plastering & leaping complete all as specified and directed by Engineer-in-Charge.

ITEM NO.30 : Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets from any position complete all as specified and directed by Engineer in Charge.

ITEM NO.31 :Dismantlling Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings in any position complete all as specified and directed by Engineer in Charge.

ITEM NO.32 :Dismantling timber scantlings as in rails, posts, rafters, purlins etc under 40 Sq cm in section from any situation complete all as specified and directed by Engineer in Charge.

ITEM NO.34 : Broken stone hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete, all as specified.

ITEM NO.35 : 25 mm thick Cement concrete (1:2:4) type B-0,using 12.5 mm graded mechanically crushed stone aggregate as in sub base of floor and pavings etc. complete all as specified and directed by Engineer-in-Charge.

ITEM NO.36 : 75 mm thick Cement concrete (1:5:10) type E-2,using 40 mm graded mechanically crushed stone aggregate as in sub base of floor complete all as specified and directed by Engineer-in-Charge.

ITEM NO. 37 : 50 mm thick, cement concrete type C-1, 1:3:6 using 20 mm graded stone aggregate, finished even & smooth without using extra cement, as in plinth protection, complete all as specified

ITEM NO. 38 : Cement concrete 75 mm thick 1 :2 4 type B 2 using 40 mm graded stone aggregate as in flooring,finishing cement concrete surface even and fair with out using extra cement, to be laid in alternate panels as directed complete all as specified

ITEM NO. 39 : 40 mm thick cement concrete 1:2:4 type B 1 (20 mm graded mechanically crushed stone aggregate) as in PCC flooring finishing concrete surface even and smooth without using extra cement complete all as specified and directed.

ITEM NO. 40 : 40 mm thick cement concrete 1:2:4 type B 1 (20 mm graded mechanically crushed stone aggregate) as in PCC flooring including spike rolling to surfaces or making impressions of expanded metal, while the concrete is green complete all as specified and directed by Engineer In Charge.

ITEM NO.41 : Plain cement concrete (1:3:6) type C-1,using 20 mm graded mechanically crushed stone aggregate as in filling of pressed steel frame /hold fast blocks etc and similar complete all as specified and directed by Engineer-in-Charge.

ITEM NO.42 : Plain cement concrete (1:4:8) type D-2,using 40 mm graded stone aggregate as in foundations, filling and mass concrete, sub base to paver blocks etc complete all as specified and directed by Engineer-in-Charge.

ITEM NO.43 : Plain cement concrete 1:3:6 type C-2, using 40mm graded stone aggregates as in concrete bed to drain pipes laid to falls in trenches in any depth including packing under and haunching against the sides for 300mm bore reinforced concrete pipes after the pipes are laid and tested complete all as specified and directed by Engineer-in-Charge.

ITEM NO.44 : Plain cement concrete 1:3:6 type C-2, using 40mm graded stone aggregates as in concrete bed to drain pipes laid to falls in trenches in any depth including packing under and haunching against the sides for 450 mm bore reinforced concrete pipes after the pipes are laid and tested complete all as specified and directed by Engineer-in-Charge.

ITEM NO. 45 Concrete bed to drain pipes of 150mm bore including packing under and hauching against the sides of pipes after they are laid and tested in PCC 1:3:6 type C2 complete all as specified and directed by Engineer in charge.

ITEM NO.46 : Plain cement concrete 1:2:4 type B-0 using 12.5mm graded stone aggregate as in roof kerbs or mud stops and benching, rounded or chamfered on edges , coving shall be 150 mm in radius mixed with acrylic based polymer water proofing compound complete all as specified and directed by Engineer-in-Charge. Note : WPC shall be paid separately.

ITEM NO.47 : Plain Cement concrete 1:2:4 type B-1 using 20mm mechanically graded crushed stone aggregate as in padding to roof to maintain the required slope and finished the surface even and smooth without using extra cement including weathering, slightly rounded or chamfered angles and throating with and including using necessary use and waste of formwork for fair finished surface complete all as specified and directed by Engineer-in-Charge.

ITEM NO.48 : Plain cement concrete 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in surface channel/drains inside the manholes , copings, slabs, benching in manholes, haunching around manhole frame for settting and the like including weathering, slightly rounded or chamfered angles and throating with and including using necessary use and waste of formwork for fair finished surface complete all as specified and directed by Engineer-in-Charge.

ITEM NO.49 : Plain cement concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregate as in surface channel/drains inside the manholes , copings, slabs, benching in manholes, haunching around manhole frame for setting and the like including weathering, slightly rounded or chamfered angles and throating with and including using necessary use and waste of formwork for fair finished surface complete all as specified and directed by Engineer-in-Charge.

ITEM NO.50 : Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped end etc. complete all as specified and directed by Engineer-in-Charge. NOTE: Inner girth only be measured and paid.

ITEM NO.51 : Add or deduct in per serial item No.50 here-in-before for each 25 mm girth or part thereof over or under 30 cm -ditto- complete all as specified and directed by Engineer-in-Charge.

ITEM NO.52 : Reinforced Cement Concrete Design mix using 20mm graded crushed stone aggregate as in chajjas and the like complete all as specified and directed by Engineer-in-Charge.

ITEM NO.53 :Reinforced Cement Concrete Design mix using 20mm graded mechanically crushed stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed by Engineer-in-Charge.

ITEM NO.54 : Reinforced Cement concrete Design Mix using 20mm graded mechanically crushed stone aggregate as in, copings, benching in Design Mix manholes, haunching around manhole frame for settting and as in lintels upto clear span 1.5 metre and the like including weathering, slightly rounded or chamfered angles and throating with and including using necessary use and waste of formwork complete all as specified and directed by Engineer-in-Charge.

ITEM NO.55 : Reinforced Cement Concrete Design Mix using 20mm graded mechanically crushed stone aggregate as in Beams, Design Mix cantilevers, bressummers, lintels over 1.5m span bed blocks,coping and the like including necessary form work complete all as specified and directed by Engineer-in-Charge..

ITEM NO.56 : Use & waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves inncluding supports, overhangs, etc. also splays between floors and beams, etc. (rough finished flat surfaces of concrete), complete all as specified and directed by Engineer-in-Charge.

ITEM NO.57 : Use & waste of Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings , slab over manholes similar work; not exceeding 200mm thick (Horizontal or sloping) (rough finished flat surfaces of concrete), complete all as specified and directed by Engineer-in-Charge.

ITEM NO.58 : Use & waste of Formwork to sides and soffits of plinth bands , lintel bands, shelves etc and edges of concrete flats, breaks in floors, openings in concrete walls, floors and roofs and sides of RCC/PCC bands in walls, horizontal or sloping, and similar work all exceeding 20cm wide complete all as specified and directed by Engineer-in-Charge.

ITEM NO.59 : Use and waste of form work to Chullah hoods, chajjas, troughs and similar items including edges and similar work for fair finish surfaces complete all as specified and directed by Engineer-in-Charge.

ITEM NO.60 : Use & waste of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide (rough finished surfaces of concrete), complete all as specified and directed by Engineer-in-Charge.

ITEM NO.61 : TMT steel bars 10mm dia and over, of grade Fe-500D cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge.

ITEM NO.62 : TMT steel bars 8 mm dia, of grade Fe-500D cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge.

ITEM NO.63 : TMT steel bars 5mm dia and over upto and including 10mm dia , of grade Fe-500D cut to length, bent to shape required, including cranking, bending stirrups spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips as in strirrups , spacers and binders complete all as specified and directed by Engineer-in-Charge.

ITEM NO.64 :Glazed ceramic tiles white of size 150x75x5/6mm with required alphabet/number printed black on tile for the purpose of marking bldg no/qtr no fixed & jointed with 3 to 6 mm thick tile adhesive with notched trowel and pointed in grout of matching shade of tiles, at location decided by the Engineer-in-Charge complete.

ITEM NO.66 : First quality, Non skid ceramic, coloured, rectified i.e. straight edge (locally known as joint free) tiles of size 600 x 600mm each and of thickness not less than 9 to 10 mm, in verical surfaces such as skirtings, dados and risers to steps etc (by cutting the tiles to required height). over and including 10 mm thick cement mortar (1:4) rendering, set jointed and pointed in grout of matching shade of tiles, complete all as specified and directed by Engineer-in-Charge.

ITEM NO.67 : First quality Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors etc. set and jointed in neat cement mortar over and inculding 15 mm thick screed in cement mortar (1:6) and pointed in white or coloured cement to match the tiles complete all as specified and directed by Engineer-in-Charge.

ITEM NO.69 : Glazed ceramic coloured tiles 450 x 300 x 6 to 7mm thick on vertical surface such as skirting , dado etc. over and including 10 mm thick rendering in CM 1:4 thick set and jointed in neat cement mortar and pointed in white or colour cement to match tiles complete all as specified and directed by Engineer-in-Charge.

ITEM NO.72 : Machine cut Kota stone slab flooring 18-22 mm thick, for staircase step (treads) in single piece (of length not more than 1200 mm), laid over over & including 15 mm thick (average thickness) cement mortar (1:3) screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (mirror finish) complete, including provn of two Nos 3x3mm grooves at tread of each step complete all as specified and directed by Engineer-in-Charge.

ITEM NO.73 : Machine Cut Kota stone slab 18-22 mm thick on vertical surfaces like riser of steps, skirting, in single piece (of length not more than 1200 mm) over & including 10 mm thick (average thickness) cement mortar (1:3) rendering and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (Mirror finish), complete all as specified and directed by Engineer-in-Charge.

ITEM NO.74 : Machine cut Kota stone slab flooring 18-22 mm thick, laid over & including 20 mm thick screed bed in cement mortar 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (mirror finish) complete all as specified and directed by Engineer-in-Charge.

ITEM NO.75 : Machine cut Kota stone slab 18-22 mm thick as in skirting, dado and pillars etc , laid over & including 10 mm thick rendering in cement mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (mirror finish) complete all as specified and directed by Engineer-in-Charge.

ITEM NO.76 : Granite jet black shade, 18-20 mm thick, (table rubbed and polished) in single piece (in one direction) machine cut, machine polished, bedded and jointed with adhesive suitable for granite/stone & pointed with grout of matching shade including necessary cutting over & including 10 mm thick (average thickness) cement mortar (1:3) screed, as in cooking platform, shelves, RCC counters, window cills & similar situations, complete all as specified and directed by Engineer-in-Charge.

ITEM NO.77 : Baroda green marble, 18-20 mm thick, (table rubbed and polished) machine cut, laid over & including 15 mm thick (average thickness) cement mortar (1:3) screed and bedded, jointed with grey cement slurry & pointed with grout of matching shade including rubbing and polishing (Granite finish), over cooking platform shelves , RCC counters, window cills & similar situations complete all as specified and directed by Engineer-in-Charge. NOTE: Full round nosing if ordered on exposed edges shall be paid separately under respective item.

ITEM NO.78 : Rounding to edges of stone (of any description) slabs one edge, such as in steps, cooking platform, and other similar situations including cutting, rubbing and polishing (mirror finish), complete all as specified and directed by Engineer-in-Charge.

ITEM NO. 79 : Providing and laying of 300x300 mm & 10mm thick Anti-Skid vitrified pavement tile in approved color & Shade in anti skid finish set and jointed in neat cement slurry and pointed in white cement & pigment to match over and including 20 mm thick screed bed in cement mortar 1:4 complete all as specified and directed by Engineer- in - Charge . (Note: Design/pattern shall be as approved by GE at the time of execution)

ITEM NO. 80 : Supply only Glass dividing strips, 3mm thick and inserted in position to conform to design width of strip 38mm complete all as specified and directed by Engineer In Charge.

ITEM NO. 81 : Supply only 4mm thick plain Asbestos cement sheet 75mm wide as in dividing strips in flooring fixed in position to conform to design all as specified and directed by Engineer In Charge.

ITEM NO.82 :Brick work using burnt clay bricks of sub class 'B' ,class designation 100, straight or curved on plan exceeding 6.00 metre mean radius built in cement mortar (1:4) including corbellings etc, raking out joints internally and also externally (above G.L.) for plastering and externally joints pointed flush below ground level in the same mortar as the work proceeds complete all as specified and directed by Engineer-in-Charge.

ITEM NO.83 :Description All as per serial item No. 82 here-in-above but except bricks -ditto-

ITEM NO.84 : Brick work with sub class 'B' bricks, class designation 100, old size bricks, straight or curved on plan exceeding 6.00 metre mean radius built in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge.

ITEM NO.85 :Description All as per serial item No. 84 here-in-before but except bricks -ditto-

ITEM NO.86 : Brick work using burnt clay bricks of sub class 'B' ,class designation 75,straight or curved on plan to any radius in half brick thick walls built in cement mortar (1:4) complete all as specified and directed by Engineer-in-Charge.

ITEM NO.87 : Precast PCC plain factory made tiles, ISI marked, 22 mm thick of size 250 mm x 250 mm, machine pressed and cut polished and set jointed and pointed in neat cement slurry and fabricated using grey cement & no pigments. over and including 15 mm thick cement mortar (1:3) bedding joints grouted flush in cement mortar (1:3) mixed with integral liquid water proofing compound over roof surfaces complete all as specified and directed by Engineer-in-Charge.

ITEM NO. 88 : Fixing only brick tiles laid flat on lime concrete & joints grouted flush in cement mortar (1:3) bedded over and including 15mm th cement morter (1:6)mixed with 5% of crude oil by weight of cement complete all as specified and directed. Note :- Tiles to be reused retrived here in before.

ITEM NO.89 : Forming jambs, etc to openings, including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work; built in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge.

ITEM NO.90 : Rendering 15 mm thick in cement mortar 1:3 (5mm thick rendering provided as floating/ setting coat over 10 mm thick rendering ) on fair/unfair faces of brick/concrete surface as in sunken portion complete all as specified and directed by Engineer-in-Charge.

ITEM NO. 91 : Rendering 15 mm thick in cement mortar 1:6, on fair faces of brick or concrete surfaces , trowelled to even and smooth surface without using extra cement, complete all as specified and directed by Engineer-in-Charge.

ITEM NO.92 : Rendering 10 mm thick in cement mortar 1:6,on fair faces of brick or concrete surfaces of walls finished even and fair without using extra cement, complete all as specified and directed by Engineer-in-Charge.

ITEM NO.93 : Rendering 15 mm thick in cement mortar 1:4, on brick or concrete surfaces mixed with water proofing compound, trowelled to even and smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge. NOTE: Water proofing compound shall be measured and paid separately.

ITEM NO.94 :15mm thick rendering in CM 1:4 on brick/concrete surface finished even and smooth using extra cement.complete all as specified & directed by Engineer in Charge.

ITEM NO.95 : Rough cast finish plastering over and including 10 mm thick rendering in cement mortar 1:3 and while it is still in plastic state, the rough cast mixture consisting of crushed stone or fine gravel aggregate ( of size between 6 to 12 mm ) mixed with coarse sand and cement in the ratio of 1: 1: 1 shall be applied and finished even. The mix of cement and sand shall be made slightly wetter than normal for rendering to ensure that larger aggregates are thoroughly covered complete all as specified and directed by Engineer-in-Charge. Rough cast finish plaster shall be applied as specified in clause 14.22 of SSR Part-I .

ITEM NO 96 Supply only liquid water proofing compound ISI Marked complete all as specified and directed.

ITEM NO.97 : Rendering 5 mm thick in cement mortar 1:3 as in soffits of slabs/Chajja/ Sunshade finishing the plastered surface even & smooth without using extra cement etc complete all as specified and directed by Engineer-in-Charge.

ITEM NO.98 : Rendering 5mm thick in cement mortar 1:3 as in soffits of slabs/chajja/sunshades over and including dubbing out average 10mm thick on irregular surface of soffits of slabs/Chajja/ Sunshades etc. in CM 1:4 complete all as specified and directed by Engineer-in-Charge.

ITEM NO.100 : Preparation of new external surfaces of walls brooming down, applying one coat of white cement based wall care putty after applying emery paper or sand paper two coats of weather proof exterior emulsion paint over a coat of primer as per manufacturers instructions etc complete all as specified and directed by Engineer-in-Charge.

ITEM No 101. : Preparation of newly plastered or old decorated wall surface applying white cement based wall care putty in two coats of minimum thickness 1.00 mm in each coat and finished thickness not less than 1.00 mm after applying emery paper or sand paper to get smooth surface to receive painting complete all as specified and directed by Engineer-in-Charge.

ITEM NO.102 : Preparation of new plastered or unplastered surfaces of walls rough cast plaster and applying two coats of cement base paint complete all as specified and directed by Engineer-in-Charge. (Note:- For Measurment purpose only flat surface shall be measured)

ITEM NO.103 : Complete removal of existing treatment from walls and applying two coats of cement base paint including preparation of surfaces complete all as specified and directed by Engineer-in-Charge.

ITEM NO.104 : Preparation of new plastered surfaces of wall and applying two coats of oil bound distemper over a coat of alkali resistant primer complete all as specified and directed by Engineer-in-Charge.

ITEM NO.105 : Providing one layer of guiniting of thickness not exceding 50 mm provided steel reinforcement and chicken wire mesh if required by means of tinned tracks or welded to existing reinforcement in CM 1:3 for top & bottom of roof slabs, beams, columns and staircase ets as directed including scaffolding at any height all as directed including mild steel chicken wire mesh of weight exceeding 0.25 kg/sqm and but not exc. 4kg/sqm complete all as specified and directed by Engineer-in-Charge.

ITEM NO.106 : Preparation of old Plastered or un-plastered surfaces of walls cornices etc by brooming down or steel wire brushing, scrapping down smoke soot moulds, moss, efflorescence salts treating oil and greasy spots etc and applying one coat of white wash on walls/ old decorated surfaces complete all as specified and directed by Engineer-in-Charge.

ITEM NO.107 : Preparation of old Plastered or un-plastered surfaces of ceilings etc by brooming down or steel wire brushing, scrapping down smoke soot moulds, moss, efflorescence salts treating oil and greasy spots etc and applying one coat of white wash on ceilings/ old decorated surfaces complete all as specified and directed by Engineer-in-Charge.

ITEM NO.108 : Complete removal of existing treatment of old ceilings, preparation of surfaces of ceilings and applying three coats of whitewash complete all as specified and directed by Engineer-in-Charge.

ITEM NO.109 : Preparation of plastered or unplastered new surfaces of ceilings and applying three coats of white wash including preparation of surface complete all as specified and directed by Engineer-in-Charge.

ITEM NO.110 : Preparation of plastered or unplastered new surfaces of walls and applying three coats of white wash including preparation of surface complete all as specified and directed by Engineer-in-Charge.

ITEM NO. 111 : Complete removal of existing treatment and applying two coats of oil bound distemper on walls over a coat primer and 2 to 3mm thick cement based wall care putty including preparation of surfacecomplete all as specified and directed.

ITEM NO.112 : Factory made Pressed steel frames, confirming to IS, having profile 125 x 60 mm , 1.25 mm thick MS sheet for doors with one or more rebates including necessary lugs,, lock strike plate, etc. and fixing only 100 mm size hinges with one shop coat of zinc chromate primer and fixing complete all as specified and directed by Engineer-in-Charge. Note: Mild Steel butt hinges shall be measured and paid separately as supply only under relevant item.

ITEM NO.113 : Factory made Pressed steel frames, confirming to IS, having profile 105 x 60 mm , 1.25 mm thick MS sheet for doors with one or more rebates including necessary lugs, lock strike plate, etc. and fixing only 100 mm size hinges,, with one shop coat of zinc chromate primer and fixing complete all as specified and directed by Engineer-in-Charge. Note: Mild Steel butt hinges shall be measured and paid separately as supply only under relevant item.

ITEM NO.114 : Plain, solid, straight 2nd class Hard wood chowkhats and frames, wrought, framed rebated on solid, rounded or chamferred, put together with glue pinned at joints supplied and fixed complete all as specified and directed by Engineer-in-Charge.

ITEM NO. 115 : Factory made solid panels PVC shutters 30mm thick (styles) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strips of 20mm width stuck inside with solvent cement for styles & wood grain printed PVC sheet for Top rail lock rail & bottom rail on either side & as gap inserted for top rail & bottom rail paneling of panel colour PVC sheet to be fitted in the MS frame welded/scaled to the stiles & rail with suitable PVC sheet beading & jointed together with solvent cement supply & fixing in the frame at site as per specification & drawing.

ITEM NO.116 : 35 mm thick factory made glazed & Skeleton shutters of 2nd class HardWood open rebated & prepared to receive glass or gauze etc without sash bar open rebated with edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing glass or guage etc size ofstiles rails etc as specified in sec 8 clause 8.24 (a) of SSR Part-I (2009) complete all as specified and directed by Engineer-in-Charge.

ITEM NO.117 : Solid PVC door frames of size 50mm x 47 mm made out of 5mm wood grain printed PVC sheet reinforced with MS square tube, and edges will be painted to match with printed sheet, supply & fixing in opening as per specification & drawing complete all as specified and directed by Engineer-in-Charge.

ITEM NO.118 : Factory made box type steel windows with pressed steel frame complete including mild steel acessories like lugs, door stopper, holdfasts, pintol hinges, handles( minimum One for each shutter), and ISI marked tower bolt 150mm size (minimum 2 for each shutter) etc. with or without glazing bars dovetailed or welded with one shop coat of zinc chromate primer, complete all as shown on drawing No. TD-276(R), Sheet No 1/4 to 2/4, 3/4, 4R/4 and as specified and directed by Engineer-in-Charge. Note: (i) Fabrication as per TD-276 (R) SH 1/4 to 2/4, 3/4, 4 (R) /4 (ii)Mode of measurement Unit will be in Kilogram for the complete window except Glass/ Gauge but incl fittings, ISI marked iron mongery and Grill/ Guard bar complete as per TD. The weight of windows will be finalized by the BOO to be convened by CWE before installation. The weight shall not include PCC back filling of the chowkhat. (iii) The PCC back filling in chowkhat of window, Sheet glass and wire gauge will be measured and paid separately against respective items.

BLANK

ITEM NO. 120 : 8 mm thick toughened glass ( 125 mm to 250 mm wide) as in shelves incl all necessary stainless steel fittings for fixing on wall complete all as specified and directed by Engineer-in-Charge.

ITEM NO.121 : Factory made steel window fixed type (fabricated from P-tube section as shown on drawings) including necessary mild steel acessories etc. with glazing bars dovetailed or welded with one shop coat of zinc chromate primer, complete all as shown on drawing No. TD-220R Sheet 3/3 and as specified and directed by Engineer-in-Charge.

ITEM NO.122 : Stainless steel butt hinges 100 mm long heavy weight complete all as specified and directed by Engineer-in-Charge.

ITEM NO.123 : Aluminium alloy anodised extruded fabricated type handle 150mm long complete all as specified and directed by Engineer-in-Charge.

ITEM NO.124 : Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) 250 mm long and fixing with bolts extruded sections or cast aluminium alloy and fixed complete all as specified and directed by Engineer-in-Charge.

ITEM NO.125 : 200 mm long Aluminium anodised barrel tower bolts of extruded section complete all as specified and directed by Engineer-in-Charge.

ITEM NO. 126 : Mild steel sliding door bolt with hasp, staple (bolt type) 250 mm long and fixing with bolts extruded sections complete all as specified & directed by Engineer in Charge.

ITEM NO.127 : Powder coated Anodised aluminium frame for doors, windows, ventilators, sliding doors/ window with one or more rebates including joining cleat for fixing etc complete all as specified and directed by Engineer-in-charge.

ITEM NO. 128 : Sheet glass 5.50mm thick, ordinary quality and glazing with beads (either supplied with shutters or to be measured separately as supply only) fixed with panel pins in square exceeding 0.5 Sqm in each pane complete all as specified and directed by Engineer-in-charge.

ITEM NO. 129 : Anodised aluminium powder coated (minimum thickness of powder coating 50 micron) three track window ( two shutters glazed & one shutters wire gauge) with frame, glazed shutters with 4 mm thick tinted glass and, with stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm including rubber bead joining cleat for fixing in position, concealed type lock for all three shutter, PVC roller etc all as specified below,including the cost of EPDM rubber /neoprene gasket required complete all as specified and directed by Engineer In Charge. Sizes of members shall be as follows :-- (a) Frame (top & side) section shall of size 92.00 x 31.75 x 1.50 mm ( Section No 20831) (b) Frame (bottom) section shall of size 92.00 x 31.75 x 1.50 mm ( Section No 20832) (c) Top & side Members of shutter Section shall be be of size 18.00 x 40.00 x 1.55mm (Section No 20738) (d) Shutter Interlock Section shall be be of size 18.00 x 40.00 x 1.45mm (Section No 20737) (e) Bottom Members of shutter Section shall be be of size 18.00 x 40.00 x 1.55mm (Section No 20736)

ITEM NO. 130 : Aluminium fixed type window fabricated with aluminium powder coated (minimum thickness of powder coating 50 micron) section for side & top rail of size 101.60 mm x 44.45 mm x 2.5 mm (section 20102) for middle rail (horizontal / vertical) of size 101.60 mm x 44.45 mm x 2.5 mm (section No 20057),included glazed with 5.50 mm thick tinted glass including EPDM rubber/neoprene gasket required. glazing clip, rubber bead, fixed in position as standard practice complete all as directed by the Engineer-in-Charge.

ITEM NO. 131 : Aluminium powder coated with approved colour ventilator, partially glazed and partially louvers, outer frame & mullion fabricated with aluminium section of size 82.50 mm x 38.00 mm x 1.70 mm thick (section No 20036), half portion glazed with 4 mm thick frosted glass including rubber beading, & glazing clip, half portion louvers of 80 mm wide & 4 mm thick frosted glass including aluminium louver patti including stainsless steel wire gauge fixing of 0.36mm dia and 1.40 width of aperture with 25x3mm thick aluminium strip with screw to upper half portion of ventilator all fitting & fixture fixed in position including taking down old ventilator complete all as specified and directed by Engineer In Charge.

BLANK

ITEM NO.133 : Rolled Mild steel Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete and conforming to Fe-290 Gde-E-165 complete all as specified and directed by Engineer-in-Charge.

ITEM NO.134 : Mild Steel Framed work as in guard bars/grills, gratings, etc.. with ends of bars shouldered/welded and/or riveted, or forged into spikes; framed guard bars/grills complete all as shown on drawing No. TD-220R Sheet 3/3 and as specified and directed by Engineer-in-Charge.

ITEM NO.135 : Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm fixed with stainless steel wire staples complete all as specified and directed by Engineer-in-Charge.

ITEM NO. 136 : Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm fixed with stainless steel wire staples as in repair complete all as specified and directed by Engineer In Charge.

ITEM NO.137 : Sheet glass 4 mm thick, ordinary quality and glazing with linseed oil pane putty & spring glazing clips using Silicon for fixing of glass in addition to glazing putty, in squares not exceeding 0.5 Sq. mtr in each pane, complete all as specified and directed by Engineer-in-Charge.

ITEM NO.138 : 4 mm thick figured glass pin head type and glazing with oil putty in square not exc 0.5 sqm each and using Silicon for fixing of glass in addition to glazing putty complete all as specified and directed by Engineer-in-Charge.

ITEM NO.139 : Preparation of new or previously untreated wooden surface of any description not otherwise described over 10cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer complete all as specified and directed by Engineer-in-Charge.

ITEM NO.140 : Preparation of newly primed surfaces and applying two of synthetic enamel paint over steel and iron surfaces of any description, not otherwise described, over 10 cm in width or girth, complete all as specified and directed by Engineer-in-Charge.

ITEM NO.141 : Preparation of new or previously untreated steel and iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engineer-in-Charge.

ITEM NO.142 : 300 mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed by Engineer-in-Charge.

ITEM NO.143 : Supply only 50 mm long cold rolled mild steel butt hinges medium weight complete all as specified and directed by Engineer-in-Charge.

ITEM NO.144 : Supply only 100 mm long cold rolled mild steel butt hinges medium weight complete all as specified and directed by Engineer-in-Charge.

ITEM NO.145 : Preparation of old or previously treated wooden surface of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed by Engineer-in-Charge.

ITEM NO.146 : Preparation of old or previously treated steel and iron surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed by Engineer-in-Charge.

ITEM NO.147 : Painting and preparation of old steel and iron surfaces of any description over 10 cm width or girth not otherwise described and applying two coats of synthetic enamel paint, complete all as specified and directed by Engineer-in-Charge.

ITEM NO.148 : 100mm long hasp and staple safety type Aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed by Engineer-in-Charge.

ITEM NO.149 : 25mm dia stainless steel fancy type drapery rod of wall thickness 0.9 mm including taking out of old pelmet/bracket, complete all as specified and directed by Engineer-in-Charge.

ITEM NO . 151 : Mild steel works as in hand rails, half round or other stock section or core for wooden handrail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) in-cluding all necessary drilling, bolting or riveting, etc., confirming to Fe-290-Gde E-165, complete all as specified.

BLANK

ITEM NO.153 : Factory made mild steel door shutter with frame, fabricated from of 1 mm thick MS sheet including provision of steel handle & locking arrangement by providing 04 lever lock with duplicate keys (of make Godrej, Link or Harrison & handle etc, including spray painting over a coat of red oxide primer and fixing the same on existing cupboard nitch MS fasteners with cement & sand mortar, complete all as specified 'shown on drawing no. TD-161.2.1.161.2.2,162.2.1 & 162.2.2 and directed by Engineer-in-Charge. Note : The shutter area only should be measued for payment.

ITEM NO. 154 40mm thick Flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on one face and decorative face veneer with lipping on one face complete all as specified.

ITEM NO.155 : Rubber strips 3 to 4mm thick & 65mm to 75mm wide fixed on bottom rail of door for covering gaps between door & floor to aviod entry of insects,dust etc complete all as specified and directed by Engineer-in-Charge.

ITEM NO.156 : LEAD FREE PVC Celuka ply 18mm thick (Minimum density 600kg/Cum) both side plain white colour, fixed with stainless steel screws, solvent cement /adhesive to make kitchen /bed rooms cabinet sides top and bottom and shelves inside the cabinets complete as per manufacturer’s specifications complete all as specified and directed by Engineer–in–Charge

ITEM NO.157 : LEAD FREE PVC Celuka ply 18mm thick (Minimum density 600kg/Cum) of single side rigid lamination of approved colour and other side plain white colour, fixed with stainless steel screws, solvent cement /adhesive to make kitchen cabinet shutters and shelves complete as per manufacturer’s specifications complete all as specified and directed by Engineer-in-Charge.

ITEM NO.158 : 12mm thick LEAD FREE PVC Celuka ply (Minimum density 600kg/Cum) of fixed with stainless steel screws, solvent cement /adhesive to make wall mount kitchen cabinet back and pull out drawer sides complete as per manufacturer’s specifications complete all as specified and directed by Engineer-in-Charge.

ITEM NO.159 : Stainless steel 304 grade wire basket cutlery of size 370 x 485mm premium quality fixed in position complete all as specified and directed by Engineer–in–Charge. Make : HETTICH, KAFF, GLEN, HARRISON and GODREJ.

ITEM NO.160 : Stainless steel 304 grade wire basket (average weight 2.5 to 4 Kg per Basket) of pull out type like plain /cup & saucer /bottle /multi purpose /2–3 shelf basket etc for kitchens of required size fixed in position complete all as specified and directed by Engineer–in–Charge. Make : HETTICH, KAFF, GLEN, HARRISON and GODREJ.

ITEM NO.161 :Ball bearing runners 45mm telescopic (KTS–20) full extension load capacity minimum 50Kgs complete all as specified and directed by Engr–in–Charge. Make : HETTICH, KAFF, GLEN, HARRISON and GODREJ.

ITEM NO.162 : ‘D’ type cabinet handles premium quality, stainless steel grade 304, gloss chrome, SN finished 150mm long matt finished complete all as specified and directed by Engineer–in–Charge. Make: HETTICH, KAFF, GLEN, HARRISON and GODREJ.

ITEM NO.163 : Auto closing hinges of size 35mm of 0 crank (KH–001) of 8 crank (KH–002) openable at 110 degree for kitchen cabinet shutters complete in all respect and fixed in position complete all as specified and directed by Engineer–in–Charge. Make : HETTICH, KAFF, GLEN, HARRISON and GODREJ.

ITEM NO.164 : Small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops,cleats and the like of 2nd class Hardwood, including all necessary' labours; articles n exc 200 cu. cm each complete all as specified and directed by Engineer-in-Charge.

ITEM NO.165 : Welding in repairs exc 2.5 cm but n.exc 5 cm in length and making good thickness of metal to be welded exc 6mm but n-exc 9mm complete all as specified and directed by Engineer-in-Charge.

ITEM NO.166 : Steel water tubing, galvanised, medium grade, ISI marked, 15 mm bore with and including all fittings , cutting, threading and fixed to walls and ceilings or laid in floors and making good the surfaces to match the existing ones complete all as specified and directed by Engineer-in-Charge.

ITEM NO.167 : Steel water tubing, galvanised, medium grade, ISI marked, 20 mm bore with and including all fittings , cutting, threading and fixed to walls and ceilings or laid in floors complete all as specified and directed by Engineer-in-Charge.

ITEM NO.168 : Refixing old GI tubing 15mm bore galvanised with all fittings as in walls,ceilings or floors etc complete all as specified and directed by Engineer-in-Charge.

ITEM NO.169 : Refixing old GI tubing 20mm bore galvanised with all fittings as in walls,ceilings or floors etc complete all as specified and directed by Engineer-in-Charge.

ITEM NO.170 : Supplying and fixing in repairs Vitreous china wash down water closet pan (Pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe), P or S trap, complete all as specified and directed by Engineer-in-Charge.

ITEM NO.171 : PVC water closet seat cover , white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed by Engineer-in-Charge.

ITEM NO.173 : 10 ltr capacity PVC valveless, syphonic action dual flush type flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, 32 mm dia flush pipe complete all as specified and directed by Engineer-in-Charge.

ITEM NO.174 : CP health faucet including 1.00 mtr long flexible tube complete all as specified and directed by Engineer-in-Charge'.

ITEM NO.175 : Supplying and fixing in repairs PTMT jet spray with 1.00 metre PVC tube , (suitable for European seat) complete all as specified and directed by Engineer-in-Charge.

ITEM NO.176 : Supplying and fixing in repair CP toilet paper holder with flap model complete all as specified and directed by Engineer-in-Charge.

ITEM NO.177 : Supplying and fixing in repairs pillars taps fancy type chromium plated, screwed down high pressure, with or without lettered 'Hot'or cold with cast copper alloy with capston head long screwed shanks and fly-nuts, screwed for iron pipe of 15mm bore and fixed complete all as specified and directed by Engineer-in-Charge.

ITEM NO.178 : Supplying and fixing in repairs vitreous china wash hand basin white flat back of size 550x440mm including CI brackets , chromium plated waste coupling, waste pipe etc., (incl all waste fittings) complete all as specified and directed by Engineer-in-Charge.

ITEM NO.180 : Supplying and fixing in repairs 15 mm fancy type chromium plated fancy type bib tap brass long body with flange screwed down high pressure CP cast copper alloy with crutch or butterfly handles screwed down suitable for 15mm bore pipe or union complete all as specified and directed by Engineer-in-Charge.

ITEM NO.181 : Bib tap, cast copper alloy, chromium plated, fancy type,Long body screwed down, high pressure,with crutch or butter fly handle suitable for 15 mm bore pipe, complete all as specified and directed by Engineer-in-Charge.

ITEM NO.182 : Bib tap, cast copper alloy, chromium plated, fancy type,Short body screwed down, high pressure,with crutch or butter fly handle suitable for 15 mm bore pipe, complete all as specified and directed by Engineer-in-Charge.

ITEM NO.183 : Bib tap, cast copper alloy, chromium plated, fancy type,Short body screwed down, high pressure,with crutch or butter fly handle suitable for 15 mm bore pipe fixed in Repair complete all as specified and directed by Engineer-in-Charge.

ITEM NO.184 : Supplying and fixing in repairs stainless steel grating doom openable 100mm size (Minimum Weight 25 grams) with/without hole including fixing with white cement complete all as specified and directed by Engineer-in-Charge.

ITEM NO.185 : Supplying and fixing in repairs 15mm bore angle cock cast copper alloy chromium plated screwed down high pressure with crutch or butterfly handle complete all as specified and directed by Engineer-in-Charge.

ITEM NO.186 : Supply & fixed 15mm bore angle cock cast copper alloy chromium plated screwed down high pressure with crutch or butterfly handle complete all as specified.

ITEM NO.187 : Supplying and fixing stop valves (concealed type),cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions,long shank and cup of 15 mm bore complete all as specified and directed by Engineer-in-Charge.

ITEM NO.188 : Supply and fixing in repair gun metal globe or gate valves with iron wheel head, screwed both ends for iron pipes 20 mm bore and fixed

BLANK

ITEM NO.190 : Supplying and fixing in repairs stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, all as specified, of 15mm bore, fancy type, chromium plated with long shank and cup (Concealed type) complete all as specified and directed by Engineer-in-Charge.

ITEM NO.191 : Supplying and fixing fancy type shower rose 125mm dia size of Rim and 30cm long CP brass pipe with swivel joint in including fixing to steel pipe or union complete all as specified and directed by Engineer-in-Charge.

ITEM NO.192 Supplying and fixing in repairs Fancy type shower rose125mm dia size of Rim and 30cm long CP brass pipe with swiwel joint in complete all as specified and directed by Engineer in Charge.

ITEM NO.193 : Supplying and fixing Chromium plated hand shower with 1.5 mtr long flexible tube complete all as specified and directed by Engineer-in-Charge.

ITEM NO.194 : CP wall mixer telephonic type for mixing hot and cold water screwed down for 15 mm dia iron pipe complete all as specified and directed by Engineer-in-Charge.

ITEM NO.195 : Supplying and fixing Corner glass shelf with CP stand complete all as specified and directed by Engineer-in-Charge.

ITEM NO.196 : Supplying and fixing Sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated guard and railing 60 cm long complete all as specified and directed by Engineer-in-Charge.

ITEM NO.197 : Supply & Fixed in repair chromium plated Soap dish, fixed to plugs with chromium plated brass screws complete all as specified and directed by Engineer-in-Charge.

ITEM NO.198 : Supply and fixed in repair brass chromium plated, tubular towel rail, 20mm dia, 60cm long between flanges complete all as specified and directed by Engineer-in-Charge.

ITEM NO.199 : PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed by Engineer-in-Charge.

ITEM NO.200: PVC connections 15mm size with PTMT nuts of length 450mm fixed in repair complete all as specified and directed by Engineer-in-Charge.

BLANK

ITEM NO.202 Stainless steel plate rack of standard size 900mmx750mm mm complete and fixing with rawl plug and steel screws of weight not less than 8kg each complete all as specified and directed by Engineer in Charge.

ITEM NO.203 Stainless steel plate rack of standard size 900mmx750mm mm complete and fixing with rawl plug and steel screws of weight not less than 8kg each fixed in repair complete all as specified and directed by Engineer in Charge.

ITEM NO.204 : Supply and fixed in repair sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste pipe incl bedding in cement mortor to dwarf wall ot cantilever brackets and connecting union to pipe overall size 915x460mm, bowl size 410x 330x160mm incl all fittings ie chromium plated waste coupling, waste pipe complete all as specified and directed by Engineer-in-Charge.

ITEM NO. 205 : Sink without drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm, waste pipe complete all as specified and directed by Engineer in Charge.

ITEM NO.207 : Supply and fixing in repair PVC cabinet with looking mirror of size 350x450mm complete all as specified and directed by Engineer-in-Charge.

ITEM NO.208 : 75mm bore cast iron bends any radius with oval access door and diminishing pieces or tapers (larger bore measured) complete all as specified and directed by Engineer-in-Charge.

ITEM NO. 209 : 75mm bore Cast Iron sand cast soil waste and vent pipe in any length with or without ears with cement joints laid in trenches or in floors complete

ITEM NO.210 : 75mm bore cast iron soil waste and vent pipe in any length with or without ears with cement joints fixed to wall complete all as specified and directed by Engineer-in-Charge.

ITEM NO.211 : 100 mm bore cast iron soil waste and vent pipe in any length with or without ears with cement joints laid in trenches or floor complete all as specified and directed by Engineer-in-Charge.

ITEM NO.212 : 100 mm bore cast iron soil waste and vent pipe in any length with or without ears with cement joints fixed to walls complete all as specified and directed by Engineer-in-Charge.

ITEM NO. 213 : Stack clamps made of 50mm by 5 mm flat iron and 16 mm dia round iron stays, incl bolts & nuts and securing ends of stays to wall or roof for 75 mm bore CI Pipe complete all as specified and directed by Engineer in Charge.

ITEM NO. 214 : Stack clamps made of 50mm by 5 mm flat iron and 16 mm dia round iron stays, incl bolts & nuts and securing ends of stays to wall or roof for 100 mm bore CI Pipe complete all as specified and directed by Engineer in Charge.

ITEM NO. 215 :Cast iron P or S trap 100 mm bore complete all as specified and directed by Engineer in Charge.

ITEM NO.216 : 100mm bore CI bends (any radius) diminishing pieces or tapers (larger bore mesured) with oval access door complete all as specified and directed by Engineer-in-Charge.

ITEM NO.217 : CI 75 mm bore branch piece single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches with oval access door complete all as specified and directed by Engineer-in-Charge.

ITEM NO.218 : CI 100 mm bore branch piece single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches with oval access door complete all as specified and directed by Engineer-in-Charge.

ITEM NO.219 : CI 100mm bore branch piece double (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches with oval access door complete all as specified and directed by Engineer-in-Charge.

ITEM NO.220 : Cast Iron 75 mm socket (double collars), complete all as specified and directed by Engineer-in-Charge.

ITEM NO.221 : Cast Iron 100mm socket (double collars), complete all as specified and directed by Engineer-in-Charge.

ITEM NO.224 : Extra over cast iron pipes and fittings if lead joint is provided in lieu of cement joint for 100 mm bore pipe include for hacking out cement joints or burning out lead joints and collecting useful materials and removing them to stores/credit complete all as specified and directed by Engineer-in-Charge.

ITEM NO.225 : Extra over cast iron pipes and fittings if lead joint is provided in lieu of cement joint for 75 mm bore pipe include for hacking out cement joints or burning out lead joints and collecting useful materials and removing them to stores/credit complete all as specified and directed by Engineer-in-Charge.

ITEM NO.226 : Reinforced cement concrete pipes, 150 mm bore, NP3 laid in trenches to any depth, with and including jointing material and testing complete all as specified and directed by Engineer-in-Charge. Note :- Excavation and earth work and concrete for bed and haunching of pipe shall be measured and paid separately

ITEM NO 227 : 75mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and directed by Engineer-in-Charge.

ITEM NO.228 : 110 mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and directed by Engineer-in-Charge.

ITEM NO.229 : PVC (SWR) junction single, (Single T 110mm), equal or unequal complete all as specified and directed by Engineer-in-Charge.

ITEM NO.230 : PVC(SWR) bends (any radius), for 110mm bore pipes, with access doors, complete all as specified and directed by Engineer-in-Charge.

ITEM NO.231 : Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc. of tank capacity n exc 500 Ltr complete including disconnecting and refixing after cleaning the tank all as specified and directed by Engineer-in-Charge.

ITEM NO.232 : Salt-glazed stoneware (SGSW) gully traps,150x150 square or round mouthed, type "P" setting and jointing to drains with cm 1:1 complete all as specified and directed by Engineer-in-Charge.

ITEM NO.233 Cast iron bends (any radius), diminishing pieces or tapers (largrer bore measured), suitable for 100 mm bore spun pipes, ISI marked, complete all as specified and directed by Engineer in Charge.

ITEM NO.234 Cast Iron vent cowl 75 mm bore size, complete all as specified and directed by Engineer in Charge.

ITEM NO.235 : Wire brushing and cleaning the top surfaces of tiles, lime terracing or cement concrete, roof surfaces etc. with water including flashings and junction of parapets etc. complete all as specified and directed by Engineer-in-Charge.

ITEM NO.236 : APP polymeric water proofing membrane minimum 3 mm thick and weighting not less than 3.6 Kg/Sqm black finish reinforced with non-woven polyster matt wt not less than 150 gms/Sqm with thermo fusable finish laid over compatible bitumen primer at the rate of 0.40 Ltr/Sqm torching over laps with a propane or butan gas torch with a over lap of 75 mm at the side and 100 mm at the ends and sealing including applying a coat of cold emulsion bituminious primer all as per manufacturers instructions incl preparation of surface complete all as specified and directed. Note :- The water proofing treatment shall be got carried out by the manufactarer or their authorised applictor's duly approved by GE in writing.

ITEM NO.237 : Heat resisting painting to surfaces of any description wood, steel, iron, concrete, brick, stone, APP surface, etc., exceeding 10cm in width or girth incl preparation of APP surfaces complete all as specified and directed by Engr-in-charge

ITEM NO.238 : Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction but welded tubes conforming to IS 1161-1979 grade St-240 as in rafters, purlins, vertical posts etc complete all as specified and directed by Engineer-in-Charge.

ITEM NO.239 : Rolled Mild steel work as in Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment for covering to steel doors, gates including necessary welding, confirming to Fe-410-W (Gde-E-250) quality-A complete all as specified and directed by Engineer-in-Charge.

ITEM NO.240 : Supply and fixing Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws etc complete all as specified and as directed by Engr-in-charge.

ITEM NO.241 : Supply and fixing Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws etc complete all as specified and as directed by Engr-in-charge.

ITEM NO. 242 :Cutting into existing manholes for connecting new drains, making good to pipe and rendering,cutting out existing benching for and forming branch channel(1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finished, and reforming benching as required for 150 mm dia pipe complete all as specified and as directed by Engineer in Charge.

ITEM NO. 245 : Plain metal false ceiling at all heights 600x600x0.5mm TEULAR EDGE TILES in global white Powder Coated with 60-70 Micron front coating laid on 24mm wide Tee grid – strong section flanges colour white having stitching on the Main Runner, 1200 mm and 600 mm Cross Tees with web height of 26mm. The tiles should have Humidity Resistance (RH) of 100%, with Light Reflection of 62%. The main runner spaced at 1200 mm max (centre to centre) securely fixed to the structural soffit . Hangers (GI wire of 4 mm dia) to be fixed by approved roof plug, level adjusters and screws etc at max 1200c/c along the main runner.The First/Last suspension system at the end of each main runner should not be greater than 450mm from the adjacent wall. Flush fitting 1200mm long cross tees to be interlocked between main runners to form 1200 x 600 mm with grid module(24X38X0.3mm).Cut cross tees longer than 600mm require independent support. 600 x 1200mm module to be formed by fitting 600mm long flush fitting cross tees centrally between the 1200 mm cross tees. Perimeter trim to be wall angles of size 24x24x0.3mm, secured to walls at 450mm max (centre to centre), including PVC clips to hold the ceiling tile, complete all as specified and as directed by the Engineer-in-Charge.

ITEM NO. 246 : Material and labour for carrying out water proofing treatment of sunken floor complete all as specified under :-- (i) The concrete / wall surface shall be cleared thoroughly of all laitance,loose particles ,dust,grease etc and any friable and unsound area which shall be chipped,cleaned and thereafter pre-wetted to a saturated surface dried condition (ii) In case of pot holes/superficial cracks,the same shall be repaired with polymer modified mortar using URP as admixture @ 10% of cement content (iii) The polymer modified mortar using URP as admixture @ 10% of cement content shall also be applied on vertical surfaces after removing of plaster upto 60 cm height (iv) The surface thus prepared shall be coated by applying 2 coats of Dr Fixit Hydrochem Super in the sunken areas and extending it upto 150 mm above the finished floor level.This includes layer of a 150 mm wide strip of an open woven glass fiber mesh over the PCC benching (Gole) on the 1st coat while it is still wet (v) Rendering 10 mm in CM 1:4 admixed with integral water proofing compound LW+ @ 200 ml per bag of cement complete all as specified and as directed by the Engineer-in-Charge.

ITEM NO. 247 : Material and labour for Precast Cement concrete Type B1, 1:2:4 using 20 mm graded crushed stone aggregates as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas,water troughs,mangers, shelves and similar articles with plain face complete all as specified and directed by the Engineer-in-Charge.

ITEM NO. 248 : Material and labour for Cement concrete (1:5:10), type E-2, using 40 mm graded crushed stone aggregates as in filling in sunken floor,rounded or chamfered on edges complete all as specified and directed by the Engineer-in-Charge.

ITEM NO. 249 :Galvanised iron tubes, `medium grade',25 mm bore, with all fittings as in spout complete all as specified and directed by the Engineer-in-Charge.

INTERNAL ELECTRIC SUPPLY WORKS

ITEM NO.251 : Taking down old and unservicable sheet metal enclosure , switch fuse unit , distribution bord any type /way / capacity including fuses,MCB's , insulator etc complete after removing all connection and making good the disturbed surface complete all as specified and directed by Engineer-in-Charge.

ITEM NO.252 : Taking down old and unservicable MCCB/MCB's etc complete after removing all connection and making good the disturbed surface complete all as specified and directed by Engineer-in-Charge.

ITEM NO.253 : Taking down ceiling fan /exhaust fan, sealing cable end, dismantling blades and removing fan, any size or any type complete all as specified and directed by Engineer-in-Charge. Note : All Ceiling fan/Exhaust fan shall be deposited to concerned AGE E/M for repair if required.

ITEM NO.254 : Taking down old unserviceable meter and old Meter shall be deposited by contractor to concerned Maintance AGE E/M store complete all as specified and directed by Engineer-in-Charge.

ITEM NO.256 : Taking up old unserviceable cable any type/any size complete all as specified and directed by Engineer-in-Charge.

ITEM NO.257 : Taking down of water heater (Geyser) any type/ size / capacity with all acessories after removing of all connection complete.Note all Geysers deposited to concerned maintanance AGE E/M store for repair if required complete all as specified and directed by Engineer-in-Charge.

ITEM NO.258 (a) One light point controlled by one switch or one (Ceiling/ Wall/ Exhaust) fan point controlled by one switch and regulator and one bell point controlled by one bell push

ITEM NO.259 (b) One 3 pin 5 Amps socket outlet on independent board

ITEM NO.260 (c ) One 3 pin 5 Amps socket outlet on same board with other switches

ITEM NO.261 (d) One light point controlled by two, two way switches.

ITEM NO.262 (e) One bell/buzzeer point controlled by one bell push.

ITEM NO.263 (a) One light point controlled by one switch or one (Ceiling/ Wall/ Exhaust) fan point controlled by one switch and regulator and one bell point controlled by one bell push

ITEM NO.264 (b) One 3 pin 5 Amps socket outlet on independent board

ITEM NO.265 (c ) One 3 pin 5 Amps socket outlet on same board with other switches

ITEM NO.266 (d) One light point controlled by two, two way switches.

ITEM NO.267 (e) One bell/buzzeer point controlled by one bell push.

ITEM NO.269 Modular Switch one way 6 Amps one module complete all as specified and directed.

ITEM NO.270 : Modular Switch one way 16 Amps one module complete all as specified and directed.

ITEM NO.271 : Modular Switch two way 6 Amps one module complete all as specified and directed.

ITEM NO.272 : Modular Bell Push 6 Amps one module complete all as specified and directed.

ITEM NO.273 : Modular Socket 6 Amps 5 Pin 2 Module complete all as specified and directed.

ITEM NO.274 : Modular Socket 6/16Amps 6 Pin 2 Module complete all as specified and directed.

ITEM NO.275 : Modular TV Socket,with metal flash box and inner/outer plate complete all as specified and directed.

ITEM NO.276 : Modular Telephone socket,with metal flash box and inner/outer plate complete all as specified and directed.

ITEM NO.277 : Modular fan Regulator step type 2 module complete all as specified and directed.

ITEM NO.279 : Switch piano flush type single pole one way, 5 Amps 230V grade complete all as specified and directed.

ITEM NO.280 : Switch piano flush type single pole two way, 5 Amps 230V grade complete all as specified and directed.

ITEM NO.281 : Bell push switch 5 Amps, 230 volt, flush type complete all as specified and directed.

ITEM NO.282 : Socket outlet multi purpose having provision for 5 pin, 5/6 Amps, flush type 230 volts grade, ISI marked, inter locking type complete all as specified and directed.

ITEM NO.283 : Switch 15Amps flush type controlled by one switch 15 Amps complete all as specified and directed.

ITEM NO.284 : Socket outlet inter locking type 6 pin 5/15Amps flush type complete all as specified and directed.

ITEM NO.285 : Ceiling rose surface backlite 65 x 20mm size three terminalcomplete all as specified and directed.

ITEM NO.286 : Electric bell AC, ding-dong type, 230 Volt, single pole complete all as specified and directed.

ITEM NO.287 : Electronic step type ceiling fan regulator , 240 volt complete all as directed by Engr-in-charge complete all as specified and directed.

ITEM NO.288 : Lamp holder, PVC/ Polycarbonate type with back plate complete all as specified & directed.

ITEM NO.289 : LED lamp 9 watt suitable for 230 volts AC supply, B22 base type complete all as specified and dierected.

ITEM NO.290 : Exhaust fan 300 mm sweep metal body, heavy duty, Single phase AC 230/240V, with energy efficient motor, pre lubricated double ball bearing, speed 900 rpm complete with louvers for wall mounting including grouting,making hole in the wall and holding down bolts, nuts, washers and provision of flexible copper conductor cable 3 core from ceiling rose to exhaust fan incl cutting of hole of required size for fixing of the exhaust fan complete all as specified and directed

ITEM NO.291 : LED tube light fitting ,1x20 watt LED 230v energy efficent Batten fitting, industrial model,aluminium body with Driver etc complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible cable copper conductor including 20 watt LED tube rod complete all as specified and directed.

BLANK

ITEM NO.293 : Security Light LED 25W made up of pressure dia cast Alumunium housing with black epoxy powder coating with cover heat resistance glass safety input voltage range 170 to 270 volts, industrial model with IP-65 protection and other connected accessories including sevice bracket of GI pipe 32mm bore medium grade of length 0.9 mtr with MS clamps, bolts, nuts, and washers and suitable reducer for connecting fitting to GI pipe as required as site and making electrical connection, complete all as specified and directed.

ITEM NO.294 : Surface mounted wall mirror LED light Compact & sturdy 10 watt LED decorative fixture with anti glare polycarbonate diffuser, multi purpose lighting solution & applications .all accessories & fixtures, internally prewired and connecting by providing copper flexible wire 23/.0076 mm twin core upto fitting, complete all as specified and directed.

ITEM NO.295 : Sub main wiring using approved colour coding as per IS with four runs of 10 sqmm PVC insulated, unsheathed cable FRLSH, flame retardant low smoke and low halogen 1100 volts grade , ISI marked with multistranded copper conductor with two runs of 10 sqmm (green colour) PVC insulated, unsheathed cable FRLSH, flame retardant low smoke and low halogen 1100 volts grade , ISI marked with multistranded copper conductor connected to common earth dolly with thimbles, drawing into & including PVC Concealed conduit ISI marked with all accessories on walls and making good of disturbed surfaces including all conduit fittings, clamps, gutties etc all as specified and directed. Note: (i) Six runs (four for main & two for earth) each of one RM of 10.00 sqmm cable together with conduit shall be considered as 1 running meter for payment purpose.

ITEM NO.296 : Sub main wiring using approved colour coding as per IS with two runs of 6 sqmm PVC insulated, unsheathed cable FRLSH, flame retardant low smoke and low halogen 1100 volts grade , ISI marked with multistranded copper conductor with one run of 6 sqmm (green colour) PVC insulated, unsheathed cable FRLSH, flame retardant low smoke and low halogen1100 volts grade , ISI marked with multistranded copper conductor connected to common earth dolly with thimbles, drawing into & including PVC Concealed conduit ISI marked with all accessories on walls and making good of disturbed surfaces including all conduit fittings, clamps, gutties etc all as specified and directed. Note: (i) Three runs (Two for main & one for earth) each of one RM of 6.00 sqmm cable together with conduit shall be considered as 1 running meter for payment purpose.

ITEM NO.297 : Sub main wiring using approved colour coding as per IS with two runs of 4 sqmm PVC insulated, unsheathed cable FRLSH, flame retardant low smoke and low halogen 1100 volts grade , ISI marked with multistranded copper conductor with one run of 4 sqmm (green colour) PVC insulated, unsheathed cable FRLSH, flame retardant low smoke and low halogen1100 volts grade , ISI marked with multistranded copper conductor connected to common earth dolly with thimbles, drawing into & including PVC Concealed conduit ISI marked with all accessories on walls and making good of disturbed surfaces including all conduit fittings, clamps, gutties etc all as specified and directed. Note: (i) Three runs (Two for main & one for earth) each of one RM of 4.00 sqmm cable together with conduit shall be considered as 1 running meter for payment purpose.

ITEM NO.298 : Sub main wiring using approved colour coding as per IS with two runs of 2.5 sqmm PVC insulated, unsheathed cable FRLSH, flame retardant low smoke and low halogen 1100 volts grade , ISI marked with multistranded copper conductor with one run of 2.5 sqmm (green colour) PVC insulated, unsheathed cable FRLSH, flame retardant low smoke and low halogen 1100 volts grade , ISI marked with multistranded copper conductor connected to common earth dolly with thimbles, drawing into & including PVC Concealed conduit ISI marked with all accessories on walls and making good of disturbed surfaces including all conduit fittings, clamps, gutties etc all as specified and directed. Note: (i) Three runs (Two for main & one for earth) each of one RM of 2.5 sqmm cable together with conduit shall be considered as 1 running meter for payment purpose.

ITEM NO.299 : Sheet metal single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amp complete all as specified and as directed

ITEM NO.300 : Sheet metal enclosure DB load line vertical TPN 6 way including 1 incommer MCCB of 63 Amps 4 pole and 18 modules for outgoing, double door IP-43 protection, powder coated, with 200 Amps rated bus bar and cable management kit complete all as specified and directed.

ITEM NO.301 : Sheet metal enclosure DB load line vertical TPN 6 way (8+18) modules for incomming & out going), 415 Volts, sheet metal powder coated, IP 43 protection including insulated bus bar of suitable capacity, cable management kit, circuit identification level complete all as specified and directed.

ITEM NO.302 : Sheet metal enclosure MCB DB, 12 way SPN, 240 volts,IP-43 protection, double door type grouting in wall in CM, flush mounted complete with 200 Amp rated bus bar complete all as specified and as directed.

ITEM NO.303 : Sheet metal enclosure MCB DB, 8 way SPN, 240 volts,IP-43 protection, double door type grouting in wall in CM, flush mounted complete with 200 Amp rated bus bar complete all as specified and as directed.

ITEM NO.304 : Sheet metal enclosure MCB DB, 2 way SPN, 240 volts,IP-43 protection, double door type grouting in wall in CM, flush mounted complete with 200 Amp rated bus bar complete all as specified and as directed.

ITEM NO.305 : MCB TP 63 Amps, 440 volts , 50 Hzs, 10 KA , "C" series, ISI marked all as specified and directed.

ITEM NO.306 : MCB SP 63 Amps, 230 volts , 50 Hzs, 10 KA , "C" series ISI marked all as specified and directed.

ITEM NO.307 : RCBO 4 Pole 63 Amps 7 module as incommer conforming to IEC 61009-1 with breaking capacity 10 KA and sensitivity 100 mA having overload, short circuit and earth leakage protection with earth fault indicator complete all as specified and directed.

ITEM NO.308 : RCBO 2 Pole 40 Amps 4 modules as incommer conforming to IEC 61009-1 with breaking capacity 10 KA and sensitivity 100 mA having overload, short circuit and earth leakage protection with earth fault indicator complete all as specified and directed.

ITEM NO.309 : RCBO 2 Pole 32 Amps 2 modules as incommer conforming to IEC 61009-1 with breaking capacity 10 KA and sensitivity 100 mA having overload, short circuit and earth leakage protection with earth fault indicator complete all as specified and directed.

ITEM NO.310 : MCB SPN 16 Amp,220 volts,50Hz, 10KA, 'C' series ISI marked all as specified and directed.

ITEM NO.311 : MCB SP 6- 40 Amps, 220 volts , 50 Hzs, 10 KA , "C" series, ISI marked all as specified and directed.

ITEM NO.312 : PVC conduit 15mm dia with 1 run of 1.5 Sqmm copper wire drawn through including cutting and chasing in wall and accessories such as bend, T, socket etc for invertor circuit complete all as specified and directed.

ITEM NO.313 : Ceiling fan AC single phase 240 Volt 50 Hz of size 1200 mm sweep complete in white colour having service value more than or equal to 6, with BLDC motor 5 star BEE rating suitable to operate with existing fan regulator, canopy cover and hanging rod with all accessories incl nuts,bolts,U clamps, 2 core PVC flexible cable 01 sqmm for making electrical connections etc, complete all as specified and directed Note :- MES No in four digits by using radium tape work over ceiling fan of specified size and colour and rate for he same including in the item rate quoted.

ITEM NO.314 : Material and labour for opening the startor & rotor of the 1200mm sweep ceiling fan cutting the existing wornout winding & rewinding the fan with superior quality super enamelled copper rewinding wire & filing the varnish as insulation between each winds & covering each loops of winding by sleeves & paper & reassembling of complete fan by fixing servicable old and new parts i.e. rubber bush of condensor & shackle housing, condensor, gun metel bushs, ball bearings twin twisted canopy, split pins complete all as per manufactures design all delevery including greasing, oiling & testing of fans complete all as specified and directed by Engineer-in-Charge.

ITEM NO.315 : All s per item No 314 here-in-before but for Exhaust fan of any size all as specified and directed by Engineer-in-charge.

ITEM NO.316 : Material and labour for cleaning the fan motor assembly body, blade of ceilingfan, fitting the cavity rubbing with sand paper, taking off old paint with th eheld of chemicals & painting the ceiling fan/exhaust fan with one coat of superior quality of synthetic enemal paint (duco paint as done on vehicale) by spraying apparatus and spraying process including writing the MES number on the ceiling fans/Exhaust fans with black colour synthetic enamel paint complete and all as specified and directed by Engineer-in-Charge.

ITEM NO.317 : Supply & fix capacitor 2.5 MFD dry type complete all as specified and directed by Engineer-In-Charge.

ITEM NO.318 : Supply & replacing heating element of 1.5/2kw as required at site for geyser of any make and any descriptions including taking out old unservicable heating elemnt complete all as specified and directed by Engineer-In-Charge..

ITEM NO.319 : Supply & replacing thermostate switch for geyser of any type ISI marked including taking out old unservicable thermostate switch complete all as specified and directed by Engineer-In-Charge .

ITEM NO.320 : TV Socket with internally grout mild steel sunken box of suitable sizes with Hylem sheet complete all as specified and directed.

ITEM NO.321 : MCB SPN 10 Amp 220 volts 50 HZ C series ISI marked complete all as specified and directed by Engineer-In-Charge .

ITEM NO.322 : Hanging only ceiling fan after repair/painting in any model/size etc and making all connection using three core copper conductor flexible cable in size 1.5 sqmm including drawn through PVC flexible conduit pipe from ceiling rose to fan connector complete all as specified and directed.

ITEM NO 323 : Fixing only exhaust fan after repair in any model/size etc and making all connection using three core copper conductor flexible cable in size 1.5 sqmm including drawn through PVC flexible conduit pipe from ceiling rose to fan connector complete all as specified and directed.

ITEM NO.324 : 10W Bulk head LED luminaries Die cast aluminium alloy body ,heat resistent prismatic glas cover ,with specially designed gasket incl all accessories & fixtures, internally prewired and connecting by provding copper flexible wire 23/.0076 mm twin core upto fitting, complete in all respects complete all as specified and directed by Engineer-in-Charge.

ITEM NO.325 : Refixing of water heater any type and any size/capacity with all accessories such as nut bolt washers ,PVC pipe etc with making all connection using three core copper conductor flexible cable drawn through in PVC flexible conduit pipe including painting with two coats of super enameled paint of existing shed complete all as specified and directed by Engineer-in-Charge.

ITEM NO.326 : Decorative Post top lantern LED luminaire with diffuser and painted spun aluminium deflector fitting 15 W with clear acrylic cover complete all as specified and as directed by Engineer-in-Charge.

ITEM NO.327 : Water heater (Geyser) storage type electric of capacity 25 Ltrs , BEE 5Star rated, ABS body, metal tank with glass lined coating, multiple heating option, shock safe plug, puf insulation, incoloy glass coated anode rod / copper heating element with ISI mark , adjustable knob for temp setting with minimum 8 Bar high working pressure, multi functional safety valve & whirl/Swirl flow technology, thermostat electronic type, complete including superior quality copper connection pipe heavy duty 15mm dia 450mm long, brass adopter for water connection with nickel coated ISI marked with fastner, nut bolts, washers duly grouted, giving shape to hole as suitable and plasetering including making good of disturbed surface as per existing surface, connecting to inlet and outlet valves, testing complete all as specified and directed by Engineer-in-Charge. Note :- Warranty certificate to be produced by the contractor from OEM for the following components before processing the bill. (a) for product -02 Years (b) for Heating element-03 years (c) for metal tank-07 Years

ITEM NO.328 : Supply and installation of smart RF Three phase meter with the following specifications : AC three phase Four wire, tamper proof static meter of class 1.0, 415 volt 50 Hz 10A-60 Amp confirming to IS : 16444 and relevant IS standard/ IEC standards with in built 865-867 MHz Radio frequency communication facility with self healing Mesh network with default and on demand display, billing data generation facility, anti tamper features. Microprocessor and LED/LCD based circuitry. • Meter should support the following data 15/30 min instantaneous data for voltage current, power factor, power comulative energy and frequency, 30 load survey data for energy, monthly billing survey for comulative energy and maximum demand. • Meter should have connect/disconnect functionality operable from billing software. • The meter should support opern communication protocol DLMS with the software. Make : Secure, L&T, Schneider

ITEM NO.329 : Supply and installation of smart RF single phase meter with the following specifications : AC single phase two wire, temper proof static meter of class 1.0, 240 volts 50 Hz 10A-60 Amp confirming to IS : 16444 and relevant IS standards/IEC standards with inbuilt 865-867 MHz Radio frequency communication facility with self healing Mesh network with default and on demand display, billing data generation facility auto tamper fealers, Micro processor and LED/LCD based circuitry . • Meter should support the following data 15/30 Min instantaneous data for voltage, current, power factor, power comulative energy and frequency, 30 load survey data for energy, monthly billing survey for comulative energy and Max. demand. • Meter should have connect/disconn at functionality operable from billing software. • The meter should support open communication protocol DLMS with the software. Make : L&T secure/Schneider.

Note for item 328 & item 329 :--Two-year comprehensive maintenance including operating costs after one year of defect liability period. They would include the following items. (a) Monthly SIM charges for the D.C.U. The contractor would ensure supply of appropriate SIM’s to ensure necessary signal availability. The contractor would change SIM or SIM provider as required. In case of network issues, the contractor would liason with the Telecom service providers for the necessary resolution. (b) Recurring SIM/SMS charges. The SMS would be issued for the payments alerts low balance alert and disconnection/connection alerts. (c) Software AMC. This would include necessary upgradations in the software such as support to the chrome browser changes, android version changes, iOS version changes. These changes happen on frequent basis and the software would support all the related changes. (d) Changes in government tariff structure. The government tariff structure changes may require software upgrade. The same would be included in AMC scope of work. (e) Remote server admin support- Ensuring adequate data base back up, upgradations in the operating system, antivirus updates, data base upgrade etc. (f) Reports development- the additional reports as needed for the success of the project would be developed. (g) Software installation on any alternate/ backup server if required. (h) The communication network monitoring and support. (i) Configuration of the repaired/replaced hardware in the system. (j) Trouble shooting and necessary action to run the system as required. (k) Software bug fixing as and when required. (l) The software would be hosted on MEITY (Ministry of Information Technology) approved by GCC (Government community cloud).

ITEM NO.329A : Supply and configuration of the web based software per meter with the following modules: (i) Meter data management Module The meter data management module would be responsible for collecting the data from the concentrator and make the data available to the billing system. The meter data management system would capture and provide the following data (a) 30 Min installations data from all the meter for seven parameter-commulative energy, comulative apparent energy (as applicable), Power, current, voltage, power factor and frequency. (b) Monthly billing survey data for comulative energy and max. demand. (c) Billing Module The billing module would collect the data from the meter data management module calculate the energy consumption, calculate billing determinant and make energy data/billing data available to admin and the end users. The billing module include functionalities for tariff setup bill format setup, bill adjustment occupation billing and vacation billing. The system would be set up as postpaid billing system. It would allow postpaid and prepaid functionality as required. (d) Occupation and vacation modules The system would support occupation/vacation and billing reports. The software would collect data from D.C.U. The software would provide access to staff as well as the occupants for the actual running data. (e) Web site- There would be a dedicated website for the AGE and BSO team to view all the data and information. The designated users in MES would have the admin access to the application. The MES staff would have also the access of the key information on an android mobiles app (for admin use only).

(f) Customer portal The system would include a customer portal for the resident/occupant to log in and view their own energy/billing data. There would be android and its own data and balance on regular basis. (g) Energy Accounting Module : The system would include feature of energy accounting. The system would be able to account for total energy blockwise facility wise and would also allow calculations of unaccounted energy in case total energy meter is also available. (h) Communication Module : The system would provide communication of energy data and bills via print,email and SMS methods. (i) Meter Master Data : The system would support meter master data repository. The system would support meter replacement process. (j) Excel Export : The system would support export of metering and billing data in excel format. (k) Customer care module : The software would include a customer care module where the user would be log in any complaint. The service provider would monitor the complaints and carry out the necessary activities for the complaints resolution. (l) Meter installation Module : The software would include an app based meter installation module where the meter installation or changes can be captured on the app itself and the reading may be demonstrated to the user, if required on the app itself. (m) Activity communication : The software support communication of the various activities such as occupation, vacation meter change, personal details change etc with the user as well as the department on email. Make : Innologix, SAP, Oracle. Note : (i) The software would be hosted on MEITY (Ministry of Information Technology) approved GCC (Government community cloud). (ii) The software would contain two years defect liability including all operating expenses such as GPRS charges, hosting charges etc.

ITEM NO.329B : Supply and installation of IP-67 protected Data concentrated unit (DCS) compatible for remote Automatic Metering infrastructure (AMI) solution and capable of communicating with the smart energy meter in the corresponding frequency band and with the data server through GPRS/Ethernet with comprehensive maintenance for two years after one year defect liability period. It would have internal memory to store data of at least 200 modules. It would have IP-67 protection. It would support auto discovery of the meter and self healing mechanism for the breaks in the RF network. Make : L&T, Secure, Schneider Cyan Connode.

ITEM NO.330 : Rigid non-metallic PVC conduit exclusive of boxes (junction/terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks of external dia size 20 mm , complete and including cutting/chasing of wall complete all as specified and directed by Engineer-in-Charge.

ITEM NO.331 : Junction Box of size 300x250x150mm with locking arrangement suitable for aluminium bus bar (02 Nos.) fixed on porecelain base insulator & 01 No MCB SP, 06A. Junction box made out of 2 mm thick MS sheet, painted with 2 coats of synthetic enamel paint over a coat of redoxide primer complete with suitable size of cable glands & MS clamps nuts, bolts & washess etc complete all as specified and directed (for Post top lantern).

ITEM NO.332 : Earthing complete with and including galvanised steel earth plate electrode 600 mm x 600 mm x 6 mm surrounded by a mixture of charcoal and salt in alternate layers burried directly in ground vertically in a pit of depth not less than 2.25 m deep below ground level with top edge of earth plate at a depth of not less than 1.5 m below ground level, connected with and including galvanised iron or steel earth wire, 4mm dia (No. 8 SWG) by means bolts, nuts, check nuts and washers made out of galvanised iron, 15 mm bore (light grade) GI pipe for protection of earthing lead, 20 mm bore (medium grade) GI pipe for watering with funnel, wire mesh and including necessary excavation and earth work, PCC 1:2:4 type B-1 pit and 50 mm thick RCC M-25(Design mix) reinforced with XPM (weight not less than 3 kg/sq m) pit cover, C.I frame, charcoal and comman salt filling in alternate layers, complete all as shown and specified in electrical plate No. 3 of SSR Part-I (2009) complete all as shown on drawings and as specified and directed by Engineer-in-Charge. Note : The unit rate includes for protecton pipe 15mm and GI earth wire 4mm dia from top of earth plate upto 7.50 metre above ground level.

ITEM NO.333 : Construction of brick masonary valve pit of 600 mm x 600mm x600mm (internal size) with 3mm thick mild steel sheet cover and angle iron frame of size 40mm x 40mm x 6mm including provision of suitable hold fasts to hold the frame, locking arrangement and lifting handle, duly painted with two coats of synthetic enamel paint over a coat of red oxide primer on MS cover & frame including necessary excavation , returning , filling , removal , plastering in CM 1:4 internally and externally complete all as specified and as directed.

ITEM NO.334 : XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric cables (heavy duty) cross sectional area 50 sq. mm, 3.5 core,stranded aluminium conductor including cable glands, cable lugs etc , to suit the cable size, 1100 volt grade, ISI marked, laid in trenches or fixing along the poles or passing through the pipes or laid under floors or through walls/ducts etc. complete all as specified.

ITEM NO.335 : XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric cables (heavy duty) cross sectional area 35 sq. mm, 3.5 core,stranded aluminium conductor including cable glands, cable lugs etc , to suit the cable size, 1100 volt grade, ISI marked, laid in trenches or fixing along the poles or passing through the pipes or laid under floors or through walls/ducts etc. complete all as specified.

ITEM NO.336 : XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric cables (heavy duty) cross sectional area 25 sq. mm, 4 core,stranded aluminium conductor including cable glands, cable lugs etc , to suit the cable size, 1100 volt grade, ISI marked, laid in trenches or fixing along the poles or passing through the pipes or laid under floors or through walls/ducts etc. complete all as specified.

ITEM NO.337 : XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric cables (heavy duty) cross sectional area 10 sq. mm, 2 core,stranded aluminium conductor including cable glands, cable lugs etc , to suit the cable size, 1100 volt grade, ISI marked, laid in trenches or fixing along the poles or passing through the pipes or laid under floors or through walls/ducts etc. complete all as specified.

ITEM NO.338 : XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric cables (heavy duty) cross sectional area 6 sq. mm, 2 core,stranded aluminium conductor including cable glands, cable lugs etc , to suit the cable size, 1100 volt grade, ISI marked, laid in trenches or fixing along the poles or passing through the pipes or laid under floors or through walls/ducts etc. complete all as specified.

BLANK

ITEM NO.340 : Un-reinforced precast concrete cable cover, Class LV, Type I, flat, size 250mm x 150mm x 40mm for protection of LT cable complete all as specified and directed.

BLANK

Note: For the purpose of arriving at lumpsum amount, the amount of credit schedule i.e Sch 'A' section VIII (i.e Rs 29,22,182.00 shall be deducted from the total amount arrived.

Total of Schedule 'A' Section-IX Rs.

Standard Const. Co.

M/s Kataria Construction Company