PROVN OF PARKING SHED, TOILET AND BATHROOM NEAR MAIN OFFICE BLDG NO P-207 AT SRC RAMGARH CANTT

Amount

Surface excavation not exceeding 30 cm deep and averaging 15cm deep and getting out in soft/ loose soil complete all as specified and directed.

Excavation in trenches in soft/loose soil not exceeding 1.5 metre deep and not exceeding 1.5 mtr width and getting out soil including forming bottom surface to required slope /gradient for laying cables, ,foundations, laying of pipes,shafts, well,cesspits, manholes etc. complete all as specified and directed.

Returning, filling in including spreading, leveling, watering and well ramming in layers of not exceeding 25 cm thick after the cables & pipes etc. are laid, jointed & tested and foundations complete all as specified and directed by Engineer-in-Charge.

Spreading, levelling in layers not exceeding 25 cm thick and ramming including watering complete all as specified & directed .

Removal of surplus excavated soil exceeding 50 Mtr distance and depositing where directed by Engineer-in-Charge at a level not exceeding 1.5 m above the starting point complete all as specified.

M&L for plain cement concrete 1:4:8 ,type D-2 (using 40 mm graded crushed stone aggregate) as in foundations,filling & mass concrete for fencing posts, foundation of pole ,struts & stay assembly etc complete all as specified and directed.

M&L reinforced cement concrete M-25 (design mix)(using 20 mm graded crushed stone aggregate) as in foundation including rafts, footings,plinth beams, and mass concrete etc.complete all as specified and directed. Note : Reinforcement & form work will be measured & paid seperately under respective item of BOQ.

Use & waste of form work to sides of concrete foundation, base of column ,rafts,footings, plinth beams, and plinth beam and similar work for rough finished flat surfaces of concrete complete all as specified and directed.

M&L reinforced cement concrete M-25 (design mix)(using 20 mm graded crushed stone aggregate) as in columns, pillars, piers,popst and struts etc.complete all as specified and directed. Note : Reinforcement & form work will be measured & paid seperately under respective item of BOQ.

Use and waste of form work to sides of columns, pillars, piers, post and struts for rough finished surface of concrete complete all as specified and directed.

M&L reinforced cement concrete M-25 (design mix) (using 20 mm graded crushed stone aggregate) as in lintels beam, floor/roof Beams, cantilevers, bressummers, etc complete all as specified and directed. Note : Reinforcement & form work will be measured & paid seperately under respective item of BOQ.

Use and waste of form work to sides and soffit of lintel ,Beam, floor /roof Beams, cantilevers, bressummers, etc for rough finished surface of concrete complete all as specified and directed.

M&L reinforced cement concrete M-25 (design mix) (using 20 mm graded crushed stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed. Note : Reinforcement & form work will be measured & paid seperately under respective item of BOQ.

Use and waste of form work to sides of soffit of suspended slab such as roof slab ,floor slab ,landing and similar work , not exceeding 200 mm thick for rough finished surface of concrete complete all as specified and directed.

Use and waste of form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor & roofs and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exceeding 10cm but not exceeding 20cm wide rough finished surface of concrete complete all as specified and directed.

M&L for Brick work with using fly ash bricks, straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6 etc complete all as specified & directed.

M& L for Brick work with fly ash bricks straight or curved on plan to any radiusin half brick thick wall built in cement mortar 1:4, complete all as specified and directed

M & L for 40 mm thick damp proof course to horizantal or verticle surface with PCC (1:2:4) type B-0 (using 12.5 mm graded crushed stone aggregate )mixed with integral water proofing compound (as per manufacturer’s instructions) conforming to IS: 2645 including covered with 100 micron thick polythene film complete all as specified & directed. (Note:Water proofing compound shall be measured and paid seprerately under respective item of "BoQ")

Supply only water proofing compound complete all as specified and directed.

S & F solid PVC door frame of size 50mm X 47mm made out of 5mm plain colour PVC sheet reinforced with mild steel square tubes suppyling & fixing in opening as per specification & drawing complete all as spcefied and directed by Engineer-in-Charge.

S & F for factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of mild steel tube for top and bottom rails. mild steel framed shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, paneling of plain colour PVC sheet to be fitted in the MS framed welded/sealed to stiles & rails with suitable PVC sheet beading & joined together with solvent cement complete all as fixing in the frame at site as per specification and drawing complete all as specified and as directed.

S & F 100mm size butt hinges medium weight cold rolled mild steel complete all as specified and directed .

S&F 150 mm long aluminium anodised barrel tower bolts of extruded section and fixed all as specified and directed.

S&F 150 mm aluminium alloy handles of extruted section type, anodised complete all as specified & directed.

M&L for framed work such as grills,gratings etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railing; framework of water tanks and similar work conforming to Fe 290- Gde E -165 complete all as specified and as directed

M&L for mild steel TMT bars 10mm dia and over grade Fe-500, cut to length, bent to shape required, including cranking bending spirally for hooping for column,, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete etc all as specified and directed.

M&L for mild steel TMT bars 08 mm dia and over grade Fe -500 , as in stirrups, spacers & binders ,cut to length, bent to shape required, including cranking bending spirally for hooping for coloumn,, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete etc all as specified and directed.

S & F for steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified & directed.

M & L for 75 mm thick plain cement concrete (1:3:6) mix, type C-1 (using 20mm graded crushed stone aggregate ) as in plinth protection, finishing the surfaces even and fair without using extra cement, including 10 mm wide, 75mm deep joints made at 3.00 m in length and filled with bitumen 85/25 grade and sand in the ratio 1:3 including necessary form work , complete all as specified and directed.

M&L for 75 mm thick plain cement concrete 1:4:8, type D-2 (using 40 mm graded crushed stone aggregate) as in sub base of flooring & mass concrete etc complete all as specified and directed.

M&L for hard core of broken stone or boulder gauge not exceeding 63mm deposited, spread & leveled in layers not exceeding 15cm thick, watered and rammed to a true surface etc complete all as specified& directed.

M & L joint free non skid coloured ceramic tiles 7 to 8 mm thick (sqaure/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc., over and including 15mm thick screed bed in cement mortar (1:6) set and jointed in neat cement slurry and pointed in coloured cement to match the existing surfaces, complete all as specified and directed.

M & L glazed ceramic coloured tiles of size 350 mm x 250 mm x7mm thick / 450 mm x 350 mm x7mm thick ,as in vertical surface such as dado/skirting etc ,set and jointed in neat cement slurry and pointed in colour cement to match the tiles, over & including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M&L for 10mm thick rendering (internal) on brick or concrete surface in cement mortar 1:6, finishing surface even and smooth without using extra cement complete all as specified and directed.

M&L for 5mm thick cement plastering in cement mortar 1:3 on concrete ceiling surfaces finished even & smooth without using extra cement omplete all as specifed and as directed.

M&L for 15mm thick rendering (external) on stone masonry surfaces or on other than fair face of brick work or concrete surface in cement mortar 1:4, finishing surface even and smooth without using extra cement complete all as specified and directed.

M&L for prepatation of new plaster surface and applying two coats of distemper oil emulsion (OBD) over a coat of alkali resistant primer (from same manufacturer of OBD) and a layer of wall care putty not less than 2mm thick complete all as specified and directed.

M&L for preparation of newely plastered surfaces of ceiling and applying three coats of white wash on ceiling complete all as specified & directed.

M & L for applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50gm/litr and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance Exterior paint of required shade (company depot tinted) with silicon additives @1.43 litre/10 Sqm, over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm over new surfaces including 1.0 mm thick plaster of paris putty applied on plastered surface even amd smooth complete all as specified & directed.

S&F 3.0 mm thick figured glass pin headed type in squares/ rectangular not exceeding 0.5 Sqm in each pane glazing with oil putty or aluminium frame/shutters with rubber neoprene beading complete etc all as specified & directed.

M&L for prepartion of new or previously untreated steel surface of any description , not otherwise described over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer on steel surface complete all as specified & directed.

S&F for GI water tubing medium grade, ISI marked, galvanised, 15 mm bore with all fittings, (such as tee, elbow, socket, union & short pieces) fixed to walls and ceiling or laid in floors including cutting chases for brick walls and making good the surface in cement mortar 1:3 complete all as specified & directed.

S&F for GI water tubing medium grade, ISI marked, galvanised, 20 mm bore with all fittings, (such as tee, elbow, socket, union & short pieces) fixed to walls and ceiling or laid in floors including cutting chases for brick walls and making good the surface in cement mortar 1:3 complete all as specified & directed.

S&F for GI water tubing medium grade, ISI marked, galvanised, 25 mm bore with all fittings, (such as tee, elbow, socket, union & short pieces) fixed to walls and ceiling or laid in floors including cutting chases for brick walls and making good the surface in cement mortar 1:3 complete all as specified & directed.

S&F rotational moulded polythene water storage tank of capacity 1000 ltrs (Cylindrical/vertical with closed type), triple layer construction, ISI marked, hoisted and fixed in position including 20 mm bore GI nipple and 25 mm bore ball/ float valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum weight 455 gms) complete all as specified and directed.

S&F stop valve 15mm bore chromium plated with long shank fancy type cast copper alloy, screwed down high pressure, screwed both ends for iron pipe or for brass ferrule fixed concealed in wall etc complete all as specified and directed.

S&F 15mm dia bore angle stop valve cast copper alloy fancy type, chromium plated with long shank and cup (concealed type) screwed down high pressure with crutch or butterfly handle screwed bot ends for iron pipe or for unions complete all as specified and directed

S&F 15mm bore long body (weight not less than 400 gm) bib tap, cast copper alloy, CP fancy type with crutch or butterfly handle, screw down, screwed for iron pipe or for brass ferrule including flange complete all as specified and directed

S & F pillar taps chromium plated, cast copper alloy with capstan head, screwed down with or without lettered 'Hot' or 'Cold' with long screw shanks and fly nuts, screwed for iron pipe and fixed for 15 mm bore complete all as specified & directed

S&F Stop valves 20 mm bore, cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions complete all as specified & directed

S&F Stop valves 25 mm bore, cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions complete all as specified & directed

S & F Toilet paper holder, vitreous China,box type fixed to wall with chromium plated brass screw complete all as specified and directed.

S& Ffor PVC connection 15 mm dia size with PTMT nuts of length 450 mm complete all as specified and directed.

M&L for 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement with chromium plated grating with or without hole complete all as specified and directed.

S&F 75 mm bore PVC(SWR) pipes single socketed , in any length with rubber ring joints, laid in trenches ,floor or in wall complete all as specified and directed.

S&F 110 mm bore PVC(SWR) pipes single socketed , in any length with rubber ring joints, laid in trenches ,floor or in wall complete all as specified and directed.

S & F 110 mm bore PVC(SWR) pipes single socketed, in any length with rubber ring joints, fixed on wall including PVC clamp properly with PCC 1:2:4 complete all as specified and directed

S & F PVC (SWR) bends 75mm bore of any radius complete all as specified and directed

S & F PVC (SWR) bends for 110mm bore of any radius complete all as specified and directed.

S&F 110 mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed.

S&F 110 mm bore PVC (SWR) vent cowl complete all as specified and directed.

S & F PVC flushing cistern 10 ltr capacity valve less syphonic action type low level with and including ball valve float and handle, PVC flush pipe 32 mm bore & PVC connection 15 mm bore 450 mm long with PTMT nuts and brackets complete set & making good disturbed surface with CM 1:3 complete all as specified and directed.

S & F vitreous China wash basin, any colour, flat back size 550 mm X 400mm including 32mm brass chromium plated waste coupling ,PVC 32 mm bore waste pipe, chromium plated Grating including bracket complete all as specified and directed.

S&F vitreous China wash down water closet (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe), fixing seat cover including connection to drain (or outgoing pipe, and to flushing pipe & antisyphonage pipe etc with aluminium hinging device complete all as specified and directed. Note : Plastic seat cover shall be measured separately as Supply only as considered under respective items.

Supply only plastic water closet seat closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device complete all as specified and directed.

S&F vitreous China urinals, bowl type angle back, size of 430 x 370 x 340 mm white (minimum),with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe)(back or corner wall type),complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets,flush pipe, grating and Union for discharge pipe etc.complete all as specified and as directed

M & L for application of water proofing treatment using APP modified roof membrane over non accessible/ non approachable RCC roof slab / chajjah / canopy / parapet wall( horizontal/vertical surface) to be executed through approved applicator of the membrane manufacturer/authorized applicator of the manufacturer with following specification etc complete all as specified and directed :- (a) Cleaning existing surface properly & apply 10 mm thick plaster /rendering in cement mortar (1:3) with WPC as per manufactures instructions (b) Applying approved bituminous based primer( conforming to IS: 3384-1995) @ 0.30 litre / Sqm manufactured by the same agency as that of APP membrane with a density 0.87-0.89 Kg per liter at 25 degree centigrade on prepared surface er . (c) Laying not less than 3mm thick APP (Atactic polypropylene Polymer modified prefabricated membrane) modified water proofing membrane weighing not less than 3.00 Kg/Sqm reinforced with non woven polyster fiber weight not less than 160gms/Sqm using butane torch by torch application with 10cm side laps and 15cm end lap. Physical property of membrane shall be as under (i) Membrane weight not less than 3.00 Kg/Sqm. (ii) Non woven polyester weight not less than 160 gms/Sqm. (iii) Softening point of membrane not less than 150 degree Celsius. (iv) Joint tensile strength-longitudinal not less than 150 Kg / Sqcm and transverse not less than 450 Kg /Sq.cm at 230 degree Celsius. (v) Tear strength - longitudinal not less than 300 N & transverse not less than 250N. (vi) Elongation of reinforcement not less than 30%. (vii) Impermeability under water pressure not less than 3 Kg/Sqcm. (d) APP modified polymeric membrane shall be laid using butane torch by Torch application with minimum 10cm side overlap and 15cm end lap. (e) Applying two coat of bituminious based Aluminium Paint @ 0.3 Kg /sqm over APP Membrane complete all as specified and directed

Excavation in post holes (or similar holes) in soft /loose soil not exceeding 0.5 cum, getting out, & removing surplus soil (material) to a distance not exceeding 50 mtr & making good surface complete all as specified & directed.

S&F roof trusses (framed), trussed, purlins, crane gantries ,rail,rafter, heavy bracket framing (beam, tee, angle, channel or flat sections) distance pieces, cleats,fastening including fabrication and fixing conforming to Fe-410-W(Gde E-250) quality-A complete all as specified & directed. Note: Drawing & design shall be approved by GE.

S&F for pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified and directed.

M&L for 60 mm thick factory made machine pressed pre-cast concrete coloured interlocking paver block of approved shade, laid in design & pattern as in footpath, light traffic parking etc, made by table vibratory method using PU mould of any shape and size conforming to IS-15658-2006 of M-35 grade laid over & including 50mm thick compacted bed over fine sand, compacting and proper embedding/ laying by vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed.

M&L for 100 mm thick plain cement concrete 1:4:8, type D-2 (using 40 mm graded crushed stone aggregate) as in sub base of flooring & mass concrete etc complete all as specified and directed.

M&Lprecast reinforced cement concrete 1:2:4 ,type B-1 (using 20 mm graded crushed stone aggregate) as in kitchen platform, shelves, cover slab (man holes), chajjas,etcand similar articles with plain faces including necessary formwork complete all as specified and directed. Note : Reinforcement will be measured & paid seperately under respective item of BOQ.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing bweinching for and forming branch channel (1/2 round or ¾ section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required in 150mm internal dia pipe complete all as specified and as directed.

M&L for plain cement concrete 1:2:4, type B-1 (using 20 mm graded crushed stone aggregates) as in kerb /benching /copings /leveliing course/window cill etc. including weathering,slightly rounded or chamfered angle and throating including use & waste of necessary form work etc complete all as specified and directed

M & L plain cement concrete (1:2:4) type B-2 (using 40 mm graded crushed stone aggregate) as in benching, & surface channel drains, etc., complete all as specified.

S & F Reinforced concrete drain pipes of 150mm dia class NP-3 laid and jointed with collars in trenches and jointed, complete all as specified and as directed by Engr-in-Charge

M & L, for Concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid in PCC 1:4:8, type D-2 (using 40mm graded crushed stone aggregate) including necessary shuttering and tested complete for 150mm bore pipe all as specified and directed.

M&L for Vetrified ceramic colour floor tiles 10 mm thick (Square/rectangular) area of each tile not exceeding 0.36 sqm, in floors & walking ways etc.,set & jointed in neat cement slurry and pointed in cloured cement to match the shade of tiles over & including 15 mm thick screed bed in cement mortar (1:4 etc complete all as specified & directed.

M&L for point wiring for one light point /exhaust fan point controlled by one way switch with using with FRLSH PVC insulated PVC unsheathed electric cable conforming to IS:694, 1100V grade AC, single core having multi stranded copper conductor of size 1.5 Sq.mm nominal cross sectional area for phase & neutral and including non metallic rigid PVC conduit ISI marked medium grade not less than 20 mm dia with all conduit accessories in concealed wiring system & 1.5 Sqmm green PVC insulated unsheathed multistranded copper conductor as a earth wire connected to earth dolly by providing lugs including sunken type anodized pressed steel sheet terminal box made out of 1.6mm thick of suitable size, for mounting fittings/junction boxes including wooden board with bakelite sheet 2.8 mm thick laminated cover make sheet for housing/fixing switches etc., complete all as specified and directed. Note: Proper colour coding to be adopted.

S & F switch piano flush button single pole one way 5 Amp, complete all as specified and as directed.

Supply and fix ceiling rose three terminals PVC/ Polycarbonate, isolated body complete all as specified.

S & F lamp holder, PVC/Polycarbonate type with back plate having matching colour to holder suitable for angle/batten fittings (ISI marked), complete all as specified.

S & F LED light fitting 1 x 20watt , 220 V, AC to produce proper illumination with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose to fitting, complete all as specified and as directed by Engr-in-Charge.

S & F LED bulb of capacity 09 watt , lumen out put (950)lm ,length 113 mm, dia 60 mm , base cap B22 (ISI mark) three star rated lamp complete all as specified and as directed by Engr-in-Charge.

S & F LED light fittings 1 x 9/10 watts integral slim LED batten with high out put diffuser 2 feet long ,220 volt ,AC decorative type with driver holder & LED lamp & all other accessories duly pre wired and making connection with and including three core copper flexible wire from connector to ceiling rose not less than 1 mtr fixed on wall with plastic gutties complete all as specified & directed.

S & F building security lights with new generation energy saving & environment friendly long life versatile pressure die-cast aluminium IP66 roadway luminaries with high power LEDs as light source & exclusively designed polycarbonate cover along with electronic driver type street light fitting 35/36 watt capacity LED and including all necessary accessories duly pre-wired, fixing on bracket with nut, bolts & washers as required at site for fixing on wall complete including all accessories duly pre-wired including provision of two core flexible copper cable of size 2.5 sqmm not less than 1.5 mtr long for connection completecomplete all as specified & directed.

S & F double door SPN distribution boards steel sheet powder coated DBs suitable for MCBs fitted with bus bar, neutral link earth bar and din rail Single phase and neutral 240 Volts suitable Amps rated busbar 4 way complete all as specified and directed.

S & F amp rating 240V, 10 kA 'B' Curve miniature circuit breaker (MCB) of single poles and neutral and current carrying capacity 32 Amp in the MCB DB complete with connection testing and commissioning all as specified and as directed.

S & F 240V, 10 kA 'B' Curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 Amp in the MCB DB complete with connection testing and commissioning all as specified and as directed.

M&L ,for earthing complete with galvanised steel earth plate electrode of size 600 mm x 600 mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below ground level, connected to galvanised earth lead wire 4.00 mm dia by means of bolts, nuts check nuts & washers of galvanised iron or steel, protected by GI pipe 15 mm bore (light grade) and watering pipe 20 mm bore GI pipe (light grade) and PCC of chamber and coping shall in 1:3:6 type C-1 using 20 mm graded stone aggregate including excavation and earth work and removal of surplus soil and filling with black cotton soil upto ground level complete all as shown in electrical plate No 3 of SSR Pt-I, 2009 with CI cover 10mm thick of size 300x300mm with charcoal dust and common salt complete and earth lead connected to panel including testing complete all as specified and directed. Note : Earth test result should not less than one ohm.

S & F 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

M&L for drilling in existing water pipe, taking new tapping from existing pipe,proper welding to the pipe surface complete all as specified and directed

Supply , laying and testing cable XLPE insulated , screened , PVC bedded , galvanized steel strip or wire armoured , electric power cable (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 Sqmm two core.

M&L sand filling in cable trenches for cable protection for clean dry sand unwashed including gently punning in a layer of 15 cm and 8 cm (total 23 cm) inthickness all across the laid portion of LT cable in trenches complete all as specified and directed. (Note:-Punned thickness shall only be considered for payment)

M&L for un-reinforced precast concrete cable cover class LV , type 1 , flat size 250 mm x 150 mm x 40mm all as specified and directed.

Supply and laying HDPE pipe of pressure rating 6kgf/cm^2 fixed with all necessary fittings for cable protection in walls , ceilings, floors , road etc complete all as specified and as directed.

upadhyay engineers and consultant

M/S SHAMBHU SHARAN SINGH

simplex infra project

M/s friend enterprises

M/S tiwari enterprises

Raj Construction

M/S KAMLESHWAR SINGH

JP ENTERPRISES

M/S Bhushan Kumar Jain