Yearly Rate of Gutter, R.C.C. Road Repairing, NP2 Pipe Line Etc. Repairing Work in Kheralu Nagarpalika, At. Kheralu Dist. Mehsana

Name of Work: Yearly Rate of Gutter, R.C.C. Road Repairing, NP2 Pipe Line Etc.

Repairing Work in Kheralu Nagarpalika, At. Kheralu Dist. Mehsana

No. Item Rate Per

Excavation for foundation up to 1.5 m. Depth including sorting out and stanching of useful 122.99 Cu. M.

materials and disposing of the excavated stuff up to 50 Meter lead (A) Loose or soft soil

Providing and laying cement concrete 1:5:10 (1 Cement : 5 Coarse Sand, 10 Hand broken

stone aggregate 40 mm nominal size) and curing complete excluding cost of form work in

(a) Foundation and Plinth (up to 10 ton)

Providing and laying cement concrete 1:4:8 (1 cement 4 coarse sand 8 hand broken stone

aggregate 40 mm nominal size) and curing complete excluding cost of Form work in. (a)

Foundation and Plinth (up to 10 ton)

Providing and laying cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone

aggregate 20 mm nominal size) and curing complete excluding cost of form work and

reinforcement for reinforced cement concrete work in

(A) Foundations, footing, base of columns and mass concrete (up to 10 ton) 3875.94 Cu. M

Providing Thermo Mechanically Treated bat (T.M.T.) (I.S.I. Mark) Conforming to I.S.-

1786 Fe-415 for R.C.C. work Including bending, binding & placing in position comp. up to

floor two level (up to 10 ton)

Uncoursed rubble masonry with hare stone with hard stone of approved quality in

foundations and plinth in cement mortar 1:6 (1 Cement : 6 Coarse Sand) Including leveling

up etc. complete (up to 10 ton)

Providing and laying ordinary cement concrete 1:3:6 (1 Cement : 3 Coarse Sand: 6 Crushed

store aggregate 20 mm nominal size) and Curing Complete including the cost of Form

work in Wall Caps/Copings (up to 10 ton)

Pointing on uncoursed stone masonry with cement mortar 1:3 (1 cement, 3 sand) (A) 96.63 Sq. M.

Filing available excavated earth (excluding rock) in trenches plinth sides of foundation etc.

layers not exceeding 20cm. in depth consolidating each deposited layer by ramming and

Brick work using common burnt clay building bricks having crushing strength not less than

35 Kg./Sq. cm in foundation and plinth in cement mortar 1 :6 ( 1 cement :6 fine sand ) in

(B) Conventional (up to 10 ton)

(2) Half Brick masonry in common burnt clay building bricks having crushing strength not

less than 35 Kg./Sq. cm in cement mortar 1:5 (1 cement :5 coarse sand) in foundation &

plinth (B) Conventional (up to 10 ton)

Providing 10 mm. thick cement plaster in single coat on fair side brick / concrete walls for

interior plastering up to floor two level and finished even and smooth in (i) cement mortar

Providing 20 mm thick sand faced cement plaster on walls up to height 10mt. Above

ground level consisting of 12mm thick backing coat of C.M. 1:3 ( 1-cement : 3-sand ) and

8mm thick finishing cost of C.M.1 :1 ( 1-Cement : 1-Sand) etc. complete.

Earthwork for embankment including breaking clods. with all lead and lift (Excluding

watering and consolidation)

(A) From borrow pits within lead width 150.00 Cu.M.

(B) From borrow pits within 0.5 km. lead 287.50 Cu.M.

(C) From borrow pits within 1.0 km. lead 297.50 Cu.M.

(D) From borrow pits within 2.0 km. lead 317.50 Cu.M.

(E) From borrow pits within 3.0 km. lead 336.25 Cu.M.

Demolition and disposal or unserviceable materials with all lead and lift. (i) Cement 680.40 Cu.M.

Box Cutting the road surface to proper slop proper and camber for making base for road

work incl. removing the excavated stuff & depositing on the road slop as directed up to

Providing & Laying ordinary concrete M-200 (1 Cement : 1.5 coarse Sand : 3 graded stone

aggregate 20 mm nominal size) and curing completed excluding the cost of formwork in

and reinforcement if rainforced concrete work in (UP TO 10 TON) including surface

vibrator and rough finish to surface as per instruction including leveling, channel vibrating

Providing and laying cement concrete flooring 1: 2: 4 (1 Cement: 2 course sand: 4 graded

stone aggregate 20 mm nominal size) laid in one layer finished with a floating coat of neat

(A) 40 mm Thick 182.70 Sq.M.

(B) 50 mm Thick 213.15 Sq.M.

Providing and fixing pre-cast Rubber Dye inter locking concrete block 60mm thick with

grade of concrete M-300 pneumatic compressed by mechanically pressed and as per 740.51 Sq.M.

approved design including 35mm sand layer for leveling and filling the joint with sand in

praper line nand level etc. completed

Providing and laying broken chine mosaic flooring for terrace using 12 mm to 20 mm

broken pieces of glazed tiles to be laid over cement mortar 1:3 to plain or slope and to be

tempered to bring mortar crème out up to surface using white cement including rounding

of junctions and extending them up to 15 cm along the wall, clearing with water and oxalic

acid etc. as directed

Providing and fixing M.S. grills required pattern of window etc. with M.S. flats at required

spacing & frame around square or round bars with round headed bolts & nuts and welding 105.24 Kg.

or by screws and including one coat of primer and two coats of oil paintng etc. complete as

approved by the Architect and Engineer-in-charge, (A) Plain grill

Providing and laying (to level or slopes and jointing reinforced concert light duty non

pressure pipes IS class NP2 of the following internal dia. meter with clears and butt ends

prepared for collar joints including testing of jointing completed.

(B) 150 mm (up to 10 ton) 257.13 Meter

(C) 250 mm (up to 10 ton) 359.74 Meter

(D) 300 mm (up to 10 ton) 677.90 Meter

(E) 450 mm (up to 10 ton) 1076.89 Meter

(F) 500 mm (up to 10 ton) 1252.18 Meter

(G) 600 mm (up to 10 ton) 1400.60 Meter

Supplying and fixing reinforced concrete R.C.C. heavy duty Non- pressure pipe with

collars for culverts including setting and jointing the pipe in C.M 1:2 watering and lying(to

level or slopes) of i.S. class NP-3 of following internal diameters.

900 mm dia. 3824.55 Rmt.

1050 mm dia. 5211.21 Rmt.

1200 mm dia. 6205.81 Rmt.

Providing and fixing 1.20 m. high fencing with 2.0 meter long M.S. angle posts 40 mm x

40 mm x 6 mm and oil painting 3 coats fixed at 2.5 m. c/c with five horizontal line and two

diagonals of galvanized steel barbed wire weighing 9.38 K.G. per 100 meter, stained and

fixed to posts with G.I. staple including fixing the posts in ground with 0.5 m. x 0.5 m. x

0.5. Block in C.C. 1:5:10 etc. Complete.

Providing Soak Pit 6' dia. & 20' deep with necessary excavation dry encores rubble maso. 30000.00 1 Nos.

or dry b.b.maso. Recast R.C.C. over 6" th. as per instruction (every 5th layer in c. m. 1:4

Providing and fixing to wall, ceiling and floor 6.0 KgF/cm2 working pressure polyethylene

pipes of the following outside dia low density complete with special flange compression

type fitting, wall clips etc. including making good the wall ceiling and floor.

(A) 20 mm 52.08 Meter

(B) 25 mm 67.31 Meter

Providing and fixing to wall, ceiling and floor 10.0 KgF/cm2 working pressure

polyethylene pipes of the following outside dia low density complete with special flange

compression type fitting, wall clips etc. including making good the wall ceiling and floor.

(C) 32 mm 81.38 Meter

(D) 40 mm 110.25 Meter

(E) 50 mm 157.50 Meter

Compaction and finishing of cement concrete road by tremix process. providing extra labor

charge for tremix (Vacuum dewatering service) process on cement road surface by using

vacuum dewatering pump floater surface vibrator including making groves and rough

finish to surface as per instruction including leveling etc. Complete Consider 10.0 mt

Length & 5 mt. width of road

Providing & Fixing Chhino & vata fitting in nagarpalika area

Providing Laying kotah stone slab flooring over 20 (average) thick base of cement mortar

1:6 (1 Cement : 6 course sand) or L.M. 1:1.5 and laid over and jointed with grey cement 627.90 Sq.M.

slurry including rubbing and polishing etc. complete

(A) 25 mm thick (up to 10 ton)

Providing and laying white glazed tiles 6mm thick in skrting risers of steps and dedo on

10mm thick cement plaster 1:3 (1-cement : 3-coarse sand) and jointed with white cement

Providing and Laying 24" x 24 " vitrified mm. thick tiles, flooring over 20 mm (Average)

base of cement mortar 1:6 (1 cement : 6 coarse sand) on new surface or fixing on existing

flooring by adhesive materials including dismantling of existing flooring and joined with

colour cement slurry including finished with flush pointing & cleaning the surface etc.

complete. for light shade finished with flush pointing in white cement (up to 10 ton)

Providing and fixing Water Closet Squatting pan ( Indian type W.C.pan) size 580mm

(Earthwork, bed concrete, foot rest and trap to be measured and paid for separately) (A)

Vitreous China -(i) Long pattern-white colour.

Providing and fixing of black granite stones name plate with engraved letters of matters in 7095.00 Smt.

any size and any language and filled with golden paints in to engraved matters. The above

matters to be done as per architect drawing and instruction on site.

Collecting and Carting Paver Block From Nagarpalika Different Area 78.00 Sqm.

Fixing Paver Block leveling and filling the joint with sand in proper line and level 100.00 Sqm.

SPEED BREAKERS: - Must be supplied with the DIV segment interlocking sub-units

made of ABS (Acrilinatorial - Boutadie - Styrene) / PE (Poly Ethylene). So that it fits

completely into one generation bump. Difficulties are pre-colored (black-yellow) and UV 2000.00 1 RMT

settled. Each sub unit should be packed with good quality reflections somewhere. The

bump is hollow from the back and will be filled with a concrete base. And then have to be

fixed on the ground surface with adhesive (epoxy and resin) and bolt or fasteners.

IN 1 METER 2 PCS (YELLOW) & 2 PCS (BLACK)

SIZE W350 X L250 X H65 MM (PER/PCS)

CAPACITY 30-40 TON

MATERIALS 100 % ABS VIRGIN PLASTIC

TOP FINISH UV FINISHED (AUTO GLOW IN NIGHT)

REFLECTOR BOTH SIDE PLATE TYPE REFLECTORS

WARRANTY 4 YEAR

SPEED BREAKERS: - Must be supplied with the DIV segment interlocking sub-units 1800.00 1 RMT

made of ABS (Acrilinatorial - Boutadie - Styrene) / PE (Poly Ethylene). So that it fits

completely into one generation bump. Difficulties are pre-colored (black-yellow) and UV

settled. Each sub unit should be packed with good quality reflections somewhere. The

bump is hollow from the back and will be filled with a concrete base. And then have to be

fixed on the ground surface with adhesive (epoxy and resin) and bolt or fasteners.

IN 1 METER 2 PCS (YELLOW) & 2 PCS (BLACK)

SIZE W350 X L250 X H50 MM (PER/PCS)

CAPACITY 25 TON

MATERIALS 30 % ABS & MIX PLASTIC

TOP FINISH BOTH SIDE PLATE TYPE REFLECTORS

REFLECTOR 3 YEAR

WARRANTY 2.0 INCH

Providing formwork of ordinary timber planking so as to give a rough finish including

centering shuttering strutting and propping etc. Height of propping and centering below

supporting floor to ceiling not exceeding 4 M. and removal of the same for in situ 179.55 Sqm.

reinforced concrete and plain concrete work in. (B) Flat surfaces such as soffits of

suspended floor roof slabs Landings and the like. (2) Floors etc. above 200mm in thickness.

Distempering with dry distemper of approved brand and manufacture (two coats) and of

required shade on wall surfaces of given an even shade, over and including a priming coat 32.24 Sqm.

of whiting after thoroughly brooming the surface free from mortar dropping and other

foreign matter.

Painting one coats (excluding priming coat) on previously printed steel and other metal

surface with synthetic enamel paint, brushing to give an even shade including cleaning the

surface of all dirt, dust and other foreign matter.

Providing, laying, spreading & compacting graded machine crushed black stone aggregates

to Wet Mix Macadam (WMM) in layers including premixing the material with water to

OMC in mechanically mix (Pug-mill) carriage of mix material by tipper to site, laying

Lowering, laying and jointing PVC pipes and specials of following class and diameter

including cost of conveyance from stores to site of works including cost of labour, material,

except cement solvent, giving satisfactory hydraulic testing as per ISI code.

63 MM 94.00 RMT

75 MM 131.00 RMT

90 MM 188.00 RMT

Providing and laying compacted WBM 150 mm thick of machine crushed BT metal of size 1139.01 CUM

45 mm to 90 mm with using and stone dust including complete

Providing and laying cement concrete work 1:2:4 (1- Cement : 2- Coarse sand : 4-graded

stone aggregates 20 mm nominal size) and curing complete excluding cost of formwork 3168.00 CMT

and reinforcement for reinforced concrete work in (A) Foundations, footings, Base or

columns and Mass concrete (more than 10 ton)

Steel work, riveted in built up sections framed work including cutting, hoisting, fixing in

position and applying a priming coat of read lead paint. (A) In beams and joists, channels 6174.18 CMT

angles Tees, flats, with connecting plates or angle cleats as in main and cross beams. Hip

and jack rafters, purlins connected to common rafters and the like. (upto 10 ton)

Providing corrugated G.I. sheet of class-3 roofing fixed with glavanished iron J or L Hooks,

Bolts and nuts 8mm diameter with bitumen and G.I. limpet washer or G.I. limpet washer. 793.10 SQmt

filled with white lead complete excluding the cost of purlins, Rafters and Trusses.(1)

mm thick sheet. (upto 10 ton)

RCC precast M.H. frame & Cover Manufacture, supply & delivery at store or at site of

work precast RCC M.200 frame & cover suitable to drainage M.H. and as per type design 1255.00 nos

& drawing including cost of reinforcement M.S. Angles or Flat, curing mold work etc.

(frame suitable for 50cm opening of MH)

RCC precast M.H. frame & Cover Manufacture, supply & delivery at store or at site of

work precast RCC M.200 frame & cover suitable to drainage M.H. and as per type design 1314.00 nos

& drawing including cost of reinforcement M.S. Angles or Flat, curing mold work etc.

(cover suitable for 50cm opening of MH)

Renovation of manhole by increasing the height at top including cost of excavation,

refitting of C.I. manhole frame and cover curing etc. complete incl. all carting and

providing of materials which is required for the purpose (except manhole frame and

cover)for all type manhole by providing RCC 1:2:4 partition walls with required

reinforcement 25cm thick and circular opening with 500mm clear dia and 0.40 mt. av. ht.

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE

having National Sanitation Foundation (NSF) seal for potable water of following dia. 136.50 RMT

nominal bore tube fittings and clamps including making good the wall, ceiling and floor

etc. complete. [A] 15mm.

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE

having National Sanitation Foundation (NSF) seal for potable water of following dia. 177.45 RMT

nominal bore tube fittings and clamps including making good the wall, ceiling and floor

etc. complete. [B] 20 mm.

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE

having National Sanitation Foundation (NSF) seal for potable water of following dia. 226.80 RMT

nominal bore tube fittings and clamps including making good the wall, ceiling and floor

etc. complete. [C] 25 mm.

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE

having National Sanitation Foundation (NSF) seal for potable water of following dia. 317.90 RMT

nominal bore tube fittings and clamps including making good the wall, ceiling and floor

etc. complete. [D] 32mm.

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE

having National Sanitation Foundation (NSF) seal for potable water of following dia. 426.36 RMT

nominal bore tube fittings and clamps including making good the wall, ceiling and floor

etc. complete. [E] 40mm.

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE

having National Sanitation Foundation (NSF) seal for potable water of following dia. 655.29 RMT

nominal bore tube fittings and clamps including making good the wall, ceiling and floor

etc. complete. [F] 50mm.

Providing laying and jointing in true line and level 15mm dia. U.P.V.C. Pipe ( SCH- 40)

for cold water including fittings as approved by Engineer In Charge. Pipe shall be fixed on

the wall with the help of clamp at every two metre C/C or shall be concealed as directed

including necessary fittings etc. including testing of pipe and joints and fixing the same

with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 25mm dia. U.P.V.C. Pipe ( SCH- 40)

for cold water including fittings as approved by Engineer In Charge. Pipe shall be fixed on

the wall with the help of clamp at every two metre C/C or shall be concealed as directed

including necessary fittings etc. including testing of pipe and joints and fixing the same

with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 32mm dia. U.P.V.C. Pipe ( SCH- 40)

for cold water including fittings as approved by Engineer In Charge. Pipe shall be fixed on

the wall with the help of clamp at every two metre C/C or shall be concealed as directed

including necessary fittings etc. including testing of pipe and joints and fixing the same

with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 40mm dia. U.P.V.C. Pipe ( SCH- 40)

for cold water including fittings as approved by Engineer In Charge. Pipe shall be fixed on

the wall with the help of clamp at every two metre C/C or shall be concealed as directed

including necessary fittings etc. including testing of pipe and joints and fixing the same

with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 50mm dia. U.P.V.C. Pipe ( SCH- 40)

for cold water including fittings as approved by Engineer In Charge. Pipe shall be fixed on

the wall with the help of clamp at every two metre C/C or shall be concealed as directed

including necessary fittings etc. including testing of pipe and joints and fixing the same

with adhesive solvent, including cost of all materials.

Providing and laying B.M 37.50 mm thick (Average)layer with Asphalt 60/70 for tack coat

at the rate of 3.4 kg./ 10 Sqm. with mechanical sprayer on B.T. surface and using B.T.

stone aggregates as per required gradation with the asphalt of 60/70 grade at the rate of

3.4% i.e.34.40 Kg./M.T. by weight by mix including heating and mixing in drum mix plant,

transporting the mix spreading the same by sensor paver finisher and consolidation by

vibrator roller MORTH specification including cost of all materials, fuel labours, tools and

plant etc using contractor own drum mix plant etc complete.

Providing & laying 20 mm. thick Mix Seal Surfacing using stone chipping & aggregate as

per M.O.R.T.&H. specification & asphalt grade 60/70 for mixing at the rate of

Kg./M.T. i.e. 5.09% of total weight of mix including heating the aggregate & asphalt in

continuous batching drum mix plant & spreading the same by paver finisher & 3331.93 M.T

consolidation with vibratory roller & flushing sand @ 0.30 Cum/ 100 Smt. including

providing all materials wquipments, tools & plants, fire wood, oil, kerosene, labour charges

etc complete using constractors own machinery drum mix plant & paver finisher etc

Scarifying gravelled macadam or Bitumen macadam surface 6cm to 10cm depth inluding 41.60 SQMT

stacking useful materials on road side and disposing off remaining stuff

Providing and laying Builtup spray grout base 37.50 mm thick (Average)layer with Asphalt

60/70 for tack coat at the rate of 2.5 kg./ 10 Sqm. with mechanical sprayer on B.T. surface

and using B.T. stone aggregates as per required gradation with the asphalt of 60/70 grade at

the rate of 1.99% i.e.19.90 Kg./M.T. by weight by mix including heating and mixing in

drum mix plant, transporting the mix spreading the same by sensor paver finisher and

consolidation by vibrator roller MORTH specification including cost of all materials, fuel

labours, tools and plant etc using contractor own drum mix plant etc complete.