E Tender No 04/EDC(Kashipur)/2024-25

Amount

Supply Item

Supply of MS Holding Clamp for SP-55 Pole duly Red Oxide Painted with Nut and Bolts and washer. (As per RESPO Specification & Drawing of UPCL)

Supply of Earth wire Clamp for SP-55 Pole duly Red Oxide Painted with Nut and Bolts and washer. (As per RESPO specification & Drawing of UPCL)

Supply of Stay clamp for SP-55 Pole duly Red Oxide Painted with Nut and Bolts and washer. (As per RESPO specification & Drawing of UPCL)

Supply of Shackle Insulator 75X90 mm with N&B (As per RESPO specification & Drawing of UPCL)

Supply of LT Clamp with N&B PCC Pole 8.5Mtr.Long (MS flat 50X6mm) (As per RESPO specification & Drawing of UPCL)

Supply of Stay Insulator 75x90 mm made of best Quality Pore Line and Without Defeets ISI Standerd. (As per RESPO Specification & Drawing of UPCL)

Supply of M.S Nut & Bolt off size

Supply of Aluminium Crimping Lug Size 120 sq mm made of best Quality Pore Line and Without Defeets ISI Standerd. (As per RESPO specification & Drawing of UPCL)

Supply of X Arm Holding Clamp for PCC Pole made of best Quality Pore Line and Without Defeets ISI Standerd. (As per RESPO specification & Drawing of UPCL)

Supply of MS Holding Clamp for SP-21 Pole duly Red Oxide Painted with Nut and Bolts and washer. (As per RESPO Specification & Drawing of UPCL)

Supply of LT Clamp with N&B for STP SP 21 (As per RESPO specification & Drawing of UPCL)

Supply of PP & Clamp for ST Pole SP-55 (MS Flat Size 65x8 mm) with 12φ x 35 mm Bolt with Nut & Washer (As per RESPO specification & Drawing of UPCL)

Supply of Suspension Clamps With I Hook. (As Per RESPO Specification & Drawing of UPCL)

Supply of Dead End Clamps With I Hook. (As Per RESPO Specification & Drawing of UPCL)

Supply of LT IPC for Distribution Box with Clamp N&B (As Per RESPO Specification & Drawing of UPCL)

Supply of Shear head Insulated Peircing Connector size 120x120 mm (As Per RESPO Specification & Drawing of UPCL)

Supply of SMC Three Phase L.T. Distribution Box for connection of LT consumer With in built Panel Lock with key, Al bus bar RYB 25x6 mm & Al bus bar N 40x6 mm. MAKE- (SINTEX/Other IS Complied Reputed Company)

Supply of LT Air Circuit Breaker (ACB) Type Complete LT Distribution Board for 250 KVA Transformer DTR fitted with 1 No 400 Amp CT Including Microprocessor release IPR-1 manual Operated Fixed Type (4 Poles as per IS-13947-2 & IEC 60947-2 with Panel and mounting structure). Make (IS Complied Reputed Company)

Supply of Al. Lug Long Barral Type Size 240 (As Per RESPO Specification & Drawing of UPCL)

Supply of Aluminium Crimping Lug Size 25 sq mm made of best Quality Pore Line and Without Defeets ISI Standerd. (As per RESPO specification & Drawing of UPCL)

TF Installation Work

Cartage of Following Material by private truck from store centre Rudrapur /Haldwani/ Kashipur to dump store approx. distance 21 to 50 Km. including loading into truck and unloading at road work site.

PCC Poles

Other Small Line Material

100 KVA T/F

250 KVA T/F

STP SP 21/23 Pole

STP SP 55 Pole

Mounting & Fixing of Fuse sets on double pole structures including making of connections complete work

Fixing of M.S. earthing rod 20×2500 mm for earthing of support as per RESPO drawing No. RES-12 including digging earth rod 0.3 m deep below ground level connected to support with earth wire 16 swg fixing of all accessories in all respect as per Specification of UPCL.

Excavation of earth for Stay set pit of size 0.6x0.6x1.2 Mtr Length in all type of soil including proper dressing of sides and ramming of bottom including getting out soil and disposal of surplus excavation soil as directed complete work in all respect.

Erection of 11 KV stay set with pole and stay rod on required tension as per specification of UPCL.

Excavation of Earth for Pole Pit of Size (.9x.6x1/6) of pole length in all type of soil including proper dressing of sides and ramming of bottom including getting out the excavated soil and diposal of surplus soil as directed complete work.

Erection of Follwing Pole Structure after digging of pit size 0.6×0.6 mtrs & 1/6 length of support on 300×300×75 mm stone pad including fixing with all accessories complete in all respect as per Specification of UPCL.

Single PCC Pole

Single SP-21 Pole

Double SP-23 Pole Structure.

Double SP-55 Pole Structure.

Grouting of pole in size (.45x.45x1/9) length of support in CC ratio 1:4:8 (1Cement:4Graded Stone:20mm nomial size:8 coarse sand) Block Including cost of material in all respect.

Grouting of Stay in size 0.6x0.6x0.3 in CC ratio 1:4:8 (1 cement : 4 graded stone 20mm nominal size : 8 coarse sand ) block including cost of Cement,sand and stone ballast back filling of soil and boulders in pit and ramming and proper alignment, leveling as per RESSPO Manual.

Muffing of pole in size (.45cmx.6cm) radious with CC ratio 1:3:6 (1Cement :3core sand:6 graded stone 10mm nomial size) Block size 45cm height from ground level Including cost of material in all respect.

Installation of New 100 KVA Transformer/Plinth/Double Pole Structure with the help of Chain Pulley/Crain Depending upon the nature of Job at work complete in all respect and Energisation of Transformer.

Installation of New 250 KVA Transformer/Plinth/Double Pole Structure with the help of Chain Pulley/Crain Depending upon the nature of Job at work complete in all respect and Energisation of Transformer.

Laying, Spreading, Stringing and sagging of 11 KV line in Rabbit Conductor 3 phase Wire with G.I. earth wire complete including fixing of all accessories in 3 Nos. conductor in parallel with binding and jumpering as per profile and profile and sagging chart.

Fabrication of Channel/angle to Single/Double pole Structure Straight Cross arm T off Top and Dropper, Brecing Channel of M.S. Channel 125x65, 100x50 & M S Angle 65x65x6 mm Cutting and Holling in all respect as per Specification of UPCL.

Laying, Spreading, Stringing and sagging of 3 phase 4 wire length Rabbit Conductor L.T. Lines of the following wire as phase wire with G.I. earth wire complete with binding and jumpering as per RESSPO Specn.

Laying, sagging & binding of AB cableof size 120 sqmm

Laying of LT XLPE Cable 3x120+1x95+1x16 sqmm.

Chemical Earthing:Earthing of distribution transformer including digging of pit of size 2.5 Mtr depth and make hole of size 150 mm. Placing of earthing electrode (to be supplied by contractor as per drawing No. A) as drawing B, connecting the same with G.I. Strip (to be supplied by contractor ) of size 35x6 mm as per drawing C for a minimum lenght 6 m. treatment of soil with highly condctive substance as per IS 30343 complete in all respect, result of earthing resistance to be recroded in M.B. before and after installation of earthing. The earth resistance after earthing should be less than 1 Ohm.

Painting of poles with angle and channel and all steel part by one coat of Rod Oxide Primer and two coats of aluminium Paint and two strip of fluorescent altemate Red and White paint 30 Cm wide upto 1.5 Mtrs. From ground level.

ST Pole SP-23/21

ST Pole SP-55

Laying of LT PVC Cable (upto 150 sqmm)

Construction of Transformer Plinth with size 2x2x1.1 meter above ground level and 0.6 meter below ground level including the cost of material such as cement, brick, ballast, sand etc. complete work and tests as per standard.

Excavation of earth of size 2.1x2.1x1.2 meter

Cement concreting work in ratio 1:4:8

Brick work in 1:4 ratio

RR massonary work in 1:6 ratio

RCC Work of 1:2:4 ratio 15 cm thickness

Cement Plaster on side walls in 1:4 ratio

Fencing of DTR

Mounting & Fixing of TPMO on double pole structures including making of connections complete work

Mounting and Fixing of Lightning arrestor on double pole structure including making all connections by G.I. strip size 35x6 mm to earth point complete work (excluding cost of G.I.Strip)

Disconnection/ Reconnection of existing service connections by Loop jumpering on main line through catenary wire 12 SWG and eye rag bolt at consumer premisse including supply of catenary wire and eye rag bolt in size 150x12 mm as per RESSPO schedule.

Installation of ACB LT Distribution Box

Fixing of X Arm Holding Clamp for SP-55

Fixing of Stay Clamp for SP-55

Fixing of PRC 25-25

Fixing of Suspension Clamp I Hook

Fixing of Dead End Clamp I Hook

Fixing of PRC L2L 95-95

Fixing of PRC L2L 120-120

Vision Electricals

KUMAUN ELECTRICALS