Design, Supply, Installation and testing of Fire Protection System at State Water Data Center Building, Gandhingar.

(A) Percentage Rate Tender (Up to INR 50 Cr.)

ITEM UNIT Quantity RATE

Supply, installation, testing, & commissioning of

electric driven Main Fire Pump suitable for automatic

operation consisting of the following specification.

Back Pull out ,centrifugal end suction type pump

complete for delivery of 137 m3/hr (2280 LPM) with

2900 rpm against a total head of 60 metres with

bronze impeller complete with Gland Packing with

Complete accessories like Base Frame,Anti vibration

Pads,Coupling etc to make the system functional in all

Squirrel cage induction , 3 phase ,415 Volt, 50 Hz,

Energy Efficient Motor

suitable for above pump. (As per the Specifications of

Motors specified in the Electrical tender Document)

Supply, installation, testing, & commissioning of

diesel engine driven Standby Fire Pump suitable for

automatic operation consisting of the following ( as

specification ).

Back Pull out ,centrifugal end suction type pump

complete for delivery of 137 m3/hr (2280 LPM)

rpm against a total head of 60 metres with bronze

impeller complete with Gland Packing with Complete

accessories like Base Frame,Anti vibration

Pads,Coupling etc to make the system functional in all

2 respect. Set 1

Air cooled (Radiator Type) Diesel Engine developing

suitable Power for the above pump Complete with

Exhaust Silencer,Hot Insulation with

Cladding,Supports ,Painting Complete with

Battery,Charging system,Cables, Panel (As per

General Specifications in electrical Tender),Diesel

Tank (Min capacity for 4 Hrs Opration) Complete with

Nozzles,Level Indicator, Isolation Valves etc with

Mounting Stand ,duly painted (Frame & Tank) in all

make the System Functional.

Supply, installation, testing, & commissioning of

electric driven automatic

pressurisation pump set consisting of the following.

Vertical in line ,multistage Jockey pump complete for

delivery of 10.8 m3/hr against a total head of

metres with bronze impeller complete with Gland

3 Packing with Complete accessories like Base Set 1 85580.00

Frame,Anti vibration Pads,Coupling etc to make the

system functional in all respect.

Squirrel cage induction , 3 phase ,415 Volt, 50 Hz,

Energy Efficient Motor suitable for above pump. (As

per the Specifications of Motors specified in the

Electrical tender Document)

Supply, Installation, testing & commissioning of

cubical type floor mounted fire control panel.The panel

shall be designed as per IS standard & Refer General

Specifications of LT Panels defined in Electrical Tender

Document including the list approved makes.The

Panel shall have facility to Operate in Auto/Manual

Mode for Electric Main Pump,Diesel Pump & Jockey

Pump). The Panel shall be designed as per the SLD

Drawing- HAL- UM - 324 - R0 - SLD For Fire Pumps

All incoming power & control cables of suitable size

from panel to motors, pressure switches And Also

Including main supply For Fire Panel to Main Electric

Supply Room etc. including termination with Copper

5 Lugs & Double Compression Cable Glands, Cable Lot 1

Tray, Pipes and Earthing as per IS standard and

Defined in General Specification of Electrification of

Electrical Tender Document including Approved

Supply, Installation, testing & commissioning of single

headed SS 304, ISI mark oblique pattern hydrant valve

with 80mm diameter flanged inlet & 63 mm

instantaneous type female out let with pvc cap- chain

spring release type lug and accessories as per IS:

Supply,Installation, testing & commissioning first aid

hose reel, Wall Mounted Drum with 30 mtr long,

25mm dia rubber lined, with ss 304 shut off nozzle of

7 6 mm dia. confirming to IS: 884, 1969 including Nos 13 8470.00

25mm dia pipe connection from riser to hose reel with

Ball Valve and Shut off Nozzle and complete Other

Supply ,Installation, testing & commissioning air

vessel of Min 450 mm dia. (8 mm thick) 1.5 meter long

made from M.S with 25mm-dia spring-loaded air

release valve, safety valve and gunmetal full way valve.

The Vessel shall be Painted with one Coat of Red Oxide

and Two Coats of Synthetic Enamel Paint . The Vessel

shall be Fixed and Mounted by Vendor including

anchoring etc. Two Numbers Extra Air vents with

Isolation Ball valves to be Provided in the Piping at the

Supply, fabrication & erection of above ground G.I. 'C'-

Class, ERW piping,

conforming to IS:1239, part-I, Heavy class up to

Various dia. and IS:3589. G.I. pipe fitting's as per IS:

Heavy class for size of Various Dia. dia.& IS:

flanges, nuts bolts & washers, 3 mm thick gasket, pipe

9 hydrostatic testing for 2 hour's at 150% of the system

pressure, hook-up etc.

painting for piping, fittings & structural pipe support,

shall be two coat of zinc

primer and two coats of fire red conf. to IS: 5, Shade

536. Complete with all

accessories as per approved drawings, specification

and direction of the

Engineer-in-charge, with all complete.

(a) Dia 150mm Meter 32 3070.65

(b) Dia 100mm Meter 328 2253.24

(c ) Dia 80mm Meter 40 1648.96

(d) Dia 50mm Meter 30 1078.83

(e ) Dia 25mm Meter 24 556.55

Supply ,Installation, testing & commissioning of

Pressure gauges - Glycerine Filled SS 304 with all

accessories like needle- valve, Syphon etc. Range 0-

16 Kg/cm2 , Dial - 100 mm, Size - 1/2 " BSP

Supply,Installation, testing & commissioning of

Diaphragm Type Pressure switch, housing shall be die

11 cast aluminum with SS 316 moving parts like Nos 3 2948.00

pressure element and socket. the range 0 to

Supply, Installation, Testing and Commissioning of

S.S. Ball Valves with all fittings required.

Excavation,back Filling and min 150 mm sand

13 bedding of Underground Pipes as defined in Technical Lot 1 11428.40

Specification strentch Depth Minimum 1 meter.

Supply, Instalation,Testing & Commissioning of NP-03

14 Grade Hume Pipe 250 mm dia. & the Meter 40 1023.00

specifications/Laying Refer Tender Specification.

Wrapping and Coating of Under Ground Piping with

15 MM Pypkot anti Corosivetape , As per Technical sqmtr 40 698.50

Supply, Installation, testing & commissioning ISI

marked C.I (SS304 Disc) Butterfly valve of P.N

Rating as per Technical Specification ,the mating

flange and additional Pair of Flanges shall be

considered to Fix the distance piece with Butterfly

(a) Dia 150mm Nos 5 4828.00

(b) Dia 100mm Nos 9 3150.00

(c ) Dia 80mm Nos 2 2841.00

(d) Dia 50mm Nos 2 1902.00

Supply,Installation, testing & commissioning ISI

marked C.I double flanged dual plate type Non- Return

17 valves(PN1.6) (SS 304 disc) Complete with Mating

Flanges,Nuts,Bolts and Gaskets, As per Technical

(a) Dia 150mm Nos 5 11548.00

(b) Dia 100mm Nos 4 8363.00

(c ) Dia 80mm Nos 2 6657.00

Design, Supply, Installation, Testing, Commissioning

of External Striner for Woltman type Bulk Water

Meter, Body: IS:210 FG200 , Strainer Frame : SS

Perforated Sheet, SS 304, Mesh (30) : 58 Perforated

Sheet, SS 304, Gasket: Rubber Cover: IS:210FG200,

Stud/Bolts/Nut: IS:1363CL4.6 & CL 4.0, Eye Bolt:

IS:1363CL4.6 & CL4.0, Plug:13% CR.SS (AISI 410),

Flange Dimensions as per IS:1538 table 6/ BS-4504

PN16, with all necessary hardware to complete the

(a) Dia 150mm Nos 2 14060.00

(b) Dia 100mm Nos 1 8344.00

S.I.T.C of ISI marked Ball Type Foot Valve, CI Body &

Nitrile Reinforced Ball

PN 1.6 rating with matching Flanges , Nut, bolts,

washer & Gaskets.

(a) Dia 150mm Nos 2 17743.00

Supply,Installation, testing & commissioning of SS

304 63mm dia branch pipe as per ISI Standard

Complete in all respect with Nuts,Bolts ,Gasket etc .As

per Technical Specification

Supply & Installation of outdoor type hose cabinet

fabricated from 16g M.S sheet with full front glass

door and locking arrangement suitable to

accommodate, 2 no of 15 meter long hose pipe and one

21 branch pipe. It should be painted with one coat of Nos 13 4578.75

primer and two coat of synthetic enamel paint.

Complete in all respect with Fixing Supports of Steel

Members Duly Painted in same color and Clamping

Supply,Installation, testing & commissioning 63mm

dia 15mtr long reinforced rubber lined hose pipe

confirming to IS: 636-1962 PART-A with ISI SS

male and female coupling, complete in all respect.

Supply,Installatation,Testing & Commissioning of gun

metal 2 way fire brigade in let connection with 63mm

23 instantaneous coupling with plug, cap, No 1 6490.00

chain,complete in all respect including,

Nuts,Bolts,Gaskets etc.

Supply & Installation of 6 Kg ABC Extinguisher of

stored pressure type with mono ammonium

phosphate discharge tube and pressure gauge

complete. Tenderer shall give 3 years guarantee on

cylinder with gas and powder. Quantity & Quality

shall be as Latest Code -15683/BIS Standard.

Supply & Installation of CO2 Fire Extinguisher of

Kg capacity fitted with screw down type high pressure

control valve with 1.0 M long rubber braided discharge

hose with horn. The Body shall be CCE approved with

IS:2878 marking and supplied with initial charge of

CO2 gas. The valve shall conform to IS:3224.Quantity

& Quality shall be as Latest Code -15683/BIS

S.I.T.C of Air release valve And Ball valve with Body

26 Brass, Internal Parts & Float HDPE complete with all Nos 2 1133.00

accessories. Dia 25mm

Supply, Installation and commissioning of Fire Alarm

27 Panel Conventional type. 8 zone, with complete No 1 13475.00

Supply, Installation and commissioning of Various

items with complete accessories

(a) smoke detectors and heat detectors(Combine) Nos 82 715.00

(b) plug in base for the smoke detectors, hooters Nos 82 206.80

(c ) Audio hooters Nos 9 896.50

(d) Manual Call Points Nos 9 872.30

(e ) On/Off Switch For Pump Nos 6 533.50

S.I.T.C of 3 core x 1 sq. mm flexible wire with pvc

29 conduit & accessories for on/off switch from pump Meter 155 157.85

house to each floor

S.I.T.C of 2 core x 1.5 sq. mm wire with Armour

30 Copper Red Cable & accessories for Alarm System to Meter 630 124.58

Supply & Fixing of Auto glow Signage's (ACP SHEET /

HEAVY FOAM SHEET)

Fire Exit 4" X 12" Nos 8 195.36

Fire Equipment 4" X 12" Nos 13 195.36

Fire Extinguisher 8" X 4" Nos 11 130.24

Incase of fire do not use lift, use, Use staircase 8’’ X

Obtaining approval on entire Fire Protection and

detection system from Local Fire Brigade authority /

Insurance co. or from any other statutory body with

all respect the Statutory Approval Charges paid to the

Statutory authorities will be re imburshed on reciept

of written approval from Statutory authority and

against submission of Payment reciepts from

Statutory Authorities.

Providing and laying cement concrete 1:2:4 (1- Cement

: 2- Coarse sand : 4- graded stone aggregates 20 mm

nominal size) and curing complete excluding cost of

formwork in (A)Foundation and Plinth

Providing, laying controlled cement concrete M

250 and curing complete including the cost of

34 form work but excluding reinforcement for Cmt 6.00 4303.84

reinforced concrete work in: Up to Plinth Level. All

type of RCC work.

Half Brick masonry in common brunt clay building

bricks having crushing strength not less than

35 Kg/Sq.Cm. in Cement mortar 1:4 (1- Cement : 4 - smt 32.00 613.94

coarse sand ) in foundation and plinth (B)

Conventional width 230mm

20mm thick sand faced cement plaster on walls upto

height 10 metres above ground level

36 consisting of 12mm thick backing coat of C.M.1:4 (1- Smt 77.60 231.66

cement : 4-sand) and 8mm thick finishing coat of C.M.

1:1 (1-cement : 1-sand) etc.complete.

Wall painting (two coats) with external paint plastic

emulsion paint of approved brand and manufacture

on undecotated wall surface to give an even shae

incl.thoroughly brushing the surface free from mortar

37 dropings and other foreign matter and sand prepared Smt 77.6 82.36

smooth incl. the cost of P/L min. two coats of Birla

putty & two coats of primer Asian or equivalent brand

.Rate includes for all lead & lift & as per directed by

Providing and fixing 10mm thick multiwall

Polycarbonate roof sheets of approved make, on

structural roofing / sky light structures in shapes as

per Architect’s drawing. The rate shall include cost of

scaffolding, screws, nuts, bolts and all necessary

fixtures and fastening etc. complete.Rate includes for

all lead & lift & as per directed by EIC.(STRUCTURAL

STEEL RATE WILL BE PAID EXTRA)

Removing & refixing pre-cast Rubber Dye / steel Dye

inter locking concrete block 60mm thick with grade of

concrete M300 pnumatic compressed / vibrated

mechanically and as per approved design Confirming

to IS 15658 : 2006 including 35 mm Sand layer for

levelling and filling the joint with sand in proper line

and level as per guidlines of IRC : SP 63-2018 etc.

Providing, supplying, fabricating and erecting in

position the structural steel for colums, grill, gates,

bars, truss, purlins, runners, cleats, insert plate, base

plate etc for all structural elements as per detail, made

up from closed structural steel hollow sections

(RHS/SHS including rolled section ) or angle or chanel

with weather resistant of Tata Structural / sections or

an approved equivalent as per details /

drawings/instructions including cutting, bending,

jointing, connecting, welding and / bolting and /

riveting and fabricating and erecting in position etc

complete for all levels as directed. The rate to include

all necessary fixtures, fastening including welding

rods of standard approvded quality etc for complete

the job. The rate shall also include the two coats of

synthetic enamel paint with priming coat & necessary

scaffolding etc. complete as directed.Rate includes for

all lead & lift & as per directed by EIC.

Preparing structural design of RCC (all Part of

Tank) Underground / Partially underground of

required capacity as per relevant I.S.

standards and constructing the same , including

excavation in all types of soil strata (Including Rock)

and shoring strutting if required, for loose soil/ to

protect from collapse due to nearby traffic load, RCC

water Tank Wall Thickness 230 mm and slab of

mm of M250 Grade , casting 120 mm thick PCC

leveling course in M-200 ,Providing and laying

precast terrazo tile 20mm thick white,black,white

and black with C.M. 1:6(:1 - cement :6 - coarse sand)

jointed with neat cement slurry mixed with pigment

to match the shade of tiles including rubbing and

polishing complete with precast tiles inside the entire

water tank , refilling the pit with proper soil and

disposing the surplus stuff all lead Including water

proof cement plaster CM 1:3 with approved water

proofing compound to inside water touching

surface to container with all type of labour and

material charges of lowering, laying, erecting/

hosting and jointing of pipe assembly to inlet,

outlet, overflow, and washout and by pass

arrangement as per hydraulic design. Providing

and fixing accessories like MS Step Irons for access

inside tank – fixed in RCC wall, CI Manhole frame

and cover, water level indicator, adequate CI

cowl type ventilators or lantern type

ventilator with stainless steel jali. B.B Chambers

for valves. Providing and applying three coats of

water proof cement paint/snowcap to the outside

face of the structure. It also includes satisfactory

water tightness Test as per relevant I .S. code and

painting name of the scheme and capacity on the

tank as per direction of engineer in charge. (For

rectangular watertak with sub soil water level below

foundation level) (For 1 Lac Liter)

I/We am/are willing to carry out the work at______________% above/below percent (Should

be written in figures and words) of the estimated rate mentioned above. Amount of my /our

tender works out

Estimated amount put to tender Estimated amount put to tender

Deduct____________% below Add___________% Above

1 The Contractor shall exhibit a board with brief details of work as directed by the

Engineer-In-Charge for which no extra payment shall be made.

2 The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.

3 GST and Income tax TDS will be deducted at a source while making payments of bills

4 In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as

per Govt. G.R. NO.: MIS102010/17/K1 Dated:30/07/2018 as stated in S.O.R.

therefore in R.C.C. items where there is a change as per actual mix design the cost of

difference of cement consumption have been deducted from the rate of original item

at the rate of input rate mentioned in all the tender.

5 Above mention Rate should be exclusive of GST

Deputy Executive Engineer Executive Engineer

WRI Sub Dn No.1 WRI Division

Ahmedabad Ahmedabad