Improvement of WSS for providing house hold connection to PC habitation Nagpuri, Rananagar and Guhan under LWSS Mungal, Rananagar in Tehsil Jaisinghpur Distt. Kangra HP.

Amount

Excavation in foundation trenches etc. in earth work in all kinds of soil such as pick work,jumper work,blasting in soft and hard rock and chiselling work including saturated soil slushy soil and under floor upto all depth and stacking the excavated soil not more than 3 metre clear from the edge of excavation and then returning the stacked soil in 15 centimetre (Fifteen centimetre)layer when required into plinth sides of foundation etc.consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed by the Engineer-in-charge within all leads and lifts.

Providing and laying cement concrete 1:6:12 (One cement is to six sand is to twelve graded stone aggregate 40 milimetre nominal size) and curing complete excluding the cost of form work in foundation and plinth within all leads and lifts as per the direction of Engineer-in-charge.

Random rubble masonry/polygonal rubble masonry (Uncoursed/brought to courses with hard stone of approved quality in foundation and plinth including levelling up with cement concrete 1:6:12)One cement is to six sand is to twelve graded stone aggregate 20 milimetre nominal size) in cement mortar 1:6 (One cement is to six sand) in breast wall/retaining walls within all leads and lifts as per the direction of Engineer-in-charge.

Boulder filling dry hand packed tightly under floor including carriage of material within all leads and lifts as per the direction of Engineer-in-charge.

Providing form work with steel plates 3.15 milimetre thick welded with angle iron in frame 30x30x5 milimetre so as to give a fair finish including centring,shuttering,strutting and propping etc.with wooden battens ballies,height of propping and centring below supporting floor two ceiling not exceeding 4 metre and removal of the same for in-situ-reinforced concrete and plain concrete work in :-

Beams, cantilever, girder and linter sides and soffits of beams haunchings cantilevers girder, bressumers and lintel not exceeding one meter in depth in all heights from floor within all leads and lifts as per the direction of Engineer-in-charge.

Slopping or battering surfaces including folded plates, where inclination to horizental plan degree not exceeding 30 degree requiring shuttering only on the under side within all leads and lifts as per the direction of Engineer-in-charge.

Flat surfaces such as soffits of suspended floors,roofs,landings and the like floors etc.upto 200 milimetre in thickness within all leads and lifts as per the direction of Engineer-in-charge.

Edges of slab and breaks in floor and walls under 20 centimetre in wide within all leads and lifts as per the direction of Engieer-in-charge.

Providing and laying cement concrete 1:2:4 (One cement is to two sand is to four graded stone aggregate 20 milimetre nominal size) and curing complete excluding the cost of form work and reinforcement for reinforced cement concrete work in:-

Suspended floors,roofs landing shelves and their supports balconies beams,girders and cantilevers upto floor two level within all leads and lifts as per the direction of Engineer-in-charge.

Providing and laying mild steel/tor steel reinforcement for reinforced cement concrete work including bending binding and placing in position complete upto floor two level within all leads and lifts as per the direction of Engineer-in-charge.

Brick work using common burnt clay building bricks in foundation and plinth in cement mortar 1:4 (One cement is to four sand) within all leads and lifts as per the direction of Engineer-in-charge.

Providing wood work in frames and doors,windows,clearstory windows and other frames wrought framed and fixed in position Second class (Deodar wood) within all leads and lifts as per the direction of Engineer-in-charge.

Providing and fixing 40 milimetre thick panelled,glazed or pannelled and glazed shutters for doors, window and clearstory window including bright finished/black enamelled iron but hinges with necessary screws in 2nd class deodar wood with in all leads and lifts as per the direction of Engineer in charge.

Providing and fixing mild steel grills of required pattern in wooden frames of windows etc. mild steel flats square or rounded bars with required bolts and nuts or by screws plain grill within all leads and lifts as per the direction of Engineer-in-charge.

40 milimetre(Forty milimetre)thick cement concrete flooring 1:2:4(One cement is to two sand is to four graded stone aggregate 20 milimetre nominal size) laid in one layer and finished with a floating coat of neat cement within all leads and lifts as per the direction of Engineer-in-charge.

15 milimetre (Fifteen milimetre) thick cement plaster in single coat on rough side of brick/stone masonry for interior plastering upto floor two level including arrises internal rounded angles chamfers and/or rounded angles not exceeding 80 milimetre in girth and finished even and smooth in cement mortar 1:6 (One cement is to six sand) within all leads and lifts as per the direction of Engineer-in-charge.

Flush pointing on brick work with cement mortar 1:3 (One cement is to three sand) including carriage of material within all leads and lifts as per the direction of Engineer-in-charge.

White washing with lime on undecorated wall surfaces two coats to give and even shade including thoroughly/brooming the surface to remove all dirt dust mortar dirt and other foreign matter within all leads and lifts as per the direction of Engineer-in-charge.

6 milimetre (Six milimetre) thick cement plaster to ceiling in cement mortar 1:3 (One cement is to three sand) within all leads and lifts as per the direction of Engineer-in-charge.

Distempering with dry distemper of approved brand and manufacture (two coats) and of required shade on undecorated wall surface to give an even shade over and including primer coat of whiting after thoroughly brushing the surface free from mortar droppings and other foreign matter including preparing the surface even and sand papered smooth with in all leads and lifts as per the direction of Engineer-in-charge.

Applying priming coat over new wood and wood based surfaces after and including preparing then surface by thoroughly cleaning oil grease,dirt and other foreign matter,sand papering and knotting with ready mixed paint brushing wood primer pink with in all leads and lifts as per the direction of Engineer-in charge.

Painting two coats (excluding priming coat) on new wood and wood based surfaces with enamel paint to give an even shade including cleaning the surface of all dirt dust and other foreign matter sand papering and stopping with enamel paint other than white with in all leads and lifts as per the direction of Enginer in charge.

Providing and fixing anodized aluminium sliding door bolts with nuts and screwed complete with in all leads and lifts as per direction of Engineer in charge

300x16 milimetre.

Providing and fixing aluminium tower bolts (barrel type bolts) with screws etc. complete with in all leads and lifts as per the direction of Engineer in charge.

200x10 milimetre.

Providing and fixing aluminium handles anodized to required colour of shade with necessary acrews etc. complete withy in all leads and lifts as per the direction of Engineer in charge.

100 milimetre.

Providing plinth protection 50 milimetre thick in cement concrete 1:3:6(One cement is to three sand is to six graded stone aggregate 20 milimetre nominal size)including finishing the top surface of concrete smooth within all leads and lifts as per the direction of Engineer-in-charge.

Providing under layer for plinth protection of 75 milimetre thick unconsolidated bed dry brick/stone aggregate 40 milimetre nominal size wall rammed and consolidated and grouted with fine sand including preparation of gound within all leads and lifts as per the direction of Engineer-in-charge.

Half brick masonry work using common burnt clay building brick in superstructure above plinth level upto floor two level in cement mortar 1:4 (One cement is to four sand) second class with in all leads and lifts as per the direction of Engineer-in-charge.

parveen kumar

AMIT KATOCH