Construction and Development works of RITES RPO Building at Gomti Nagar, Lucknow

Amount

Total Amount of BoQ 2

Amount after unconditional Rebate

Description of Work / Item(s)

Amount

Total of BoQ 3, BoQ 4, BoQ 5 and BoQ 6

Total Amount of BoQ3 (Item Rate)

Total Amount of BoQ4 (Percentage Rate)

Total Amount of BoQ5 (Percentage Rate)

Total Amount of BoQ6 (Percentage Rate)

Description of Work / Item(s)

Amount

Schedule - (E) Bill of Quantites for Non Schedule Items (MR ITEMS)

CIVIL

NS 1 - Construction of apron drain of size 150mm wide and minimum depth 150mm, made with brick work with class designation 7.5 (230 mm thick wlls) having base concrete 1:4:8 (75mm thick) with cement conrete flooring 40 mm thick (1:2:4) and finished with 15mm thick plaster with top coat of neat cement and having required slope. This item also includes excavation & refilling of earth.

NS 2 - Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm at terrace level, for all leads & lifts, all complete as per direction of Engineer -incharge.

NS 3 - Providing and fixing GI hexagonal chicken wire mesh of size 12mm x 22gauge at the junction of disimilar surfaces of brick masonry wall and R C C column & beams including necessary nails for fixing etc, complete all as per specification and direction of Engineer -in -charge for all floor at all heights.

NS 4 - Supplying & applying paint on truss & doors with PU paint of approved brand and manufacture of required colour to give an even shade : New work (two or more coats) including a coat of approved primer.

NS 5 - Providing and fixing SS tower bolts, ISI marked, with necessary screws etc. complete as approved by Engineer-in-charge :

NS 5.1 - 250x10 mm

NS 5.2 - 150x10 mm

NS 6 - Providing and fixing SS sliding door bolts, with nuts and screws etc. complete as approved by engineer-in-charge:

NS 6.1 - 300x16 mm

NS 6.2 - 250x16 mm

NS 7 - Providing and fixing bright finished SS hanging type floor door single rubber stopper with necessary screws, etc. complete as approved by Engineer-in-charge.

NS 8 - Providing and fixing Stainless steel 304 Grade H- type pull handle of size min 32 mm dia and 1200mm long of approved make including SS screws, including making holes of required size in shutter etc. complete as per direction of Engineer-in-Charge.

NS 9 - Providing and fixing SS Bottom patch Lock with cylinder of approved make including necessary screws etc. all complete as approved by Engineer-in-charge

NS 10 - Providing and fixing SS floor mounted half dome door stopper of dia 45mm including necessary screws etc. all complete.

NS 11 - Providing and fixing of ‘Unistone’ or equivalent Glass Reinforced Concrete (G.R.C) Wall Cladding Tiles in approved design, size, texture, thickness, pattern and color. The thickness of the tiles should range between 12 to 18 mm (depending on the texture of the tile), allowing variance of ± 2 mm in accordance with IS: 1237‐1980. The composition of tiles should be ‘43’ Grade Portland cement, reinforced with Alkali Resistant Glass Fiber and homogeny pigmentation should be done with exterior grade synthetic inorganic iron oxide pigments manufactured by ‘BAYFERROX / Lanxess (Germany)’ or equivalent. The pigmentation should be homogeneous and in accordance with British Standards BS EN 12878:1999. The other additives should be fine washed graded quartz, super plasticizers and integrated water proofing agents and others. The tiles should be produced with high vibration technology and concrete mix design compressive strength equivalent to M‐40 Grade@28 days. The top surface of the tiles should be sealed with acrylic lacquer resulting in surface water absorption of tiles, less than 1% and water absorption by 24 hrs immersion method, less than 8%. The tiles should be applied on a rough plaster of 1:3 cement mortar 1:3 (1 cement: 3 coarse sand) and the fixing of tiles should be done by ‘Unistone’ tile adhesive or equivalent as per manufacturer’s laying instruction.

NS 12 - Constructing brick masonry inspection chamber 60x60x90 cm with bricks of class designation 75 in cement mortar 1:4 (1 cement : 4 coarse sand) including CI cover with frame LIGHT WEIGHT complete in all respect. i/c necessary excavation, foundation concrete 1:5:10 , fixing of CI frame with cover and inside plastering with cement mortar 1:3 12 mm thick, finished with a floating coat of neat cement complete as per standard design etc. complete in all respect.

NS 13 - Providing, and fixing of CP insect repellar floor drain complete

NS 14 - Supplying and fixing of SS ball bearing hinges of size 100x75x3mm complete with SS screw of BB1953 BeckerFS/Dorma/Geze make (4no. Per panel required for all doors)

NS 15 - Supplying and fixing of anchor fastner of maximum10mmx 80mm length. (HILTI/FISHER required for all door )

NS 16 - Providing and supplying heavy duty HITRE 500 V3 or equivalent with Rebar with a predefined ration (3:1) of resin and hardner in a soft foil pack. The product should be approved bt ETA,ICC,CSTB,COLA,BZS with shock approval, seismic approval in Anchors and Rebars to use in cracked/uncracked concrete. Drilling hole with double flute type drill bits/hollow drill bits to the required depth by rotary hammer drill, cleaning with brush and jet of clean air, filling resin and hardner using serrated nozzle to eliminate mixing error with standard HDE A22 battery dispenser along with piston plug and extension hose for longer depths to ensure no air bubbles are in the hole and then fixing the rebar, conducting occassional site inspection, executing work by trained personnel and occassional supervision from the manufactures representative. The installation and setting instruction should be strictly followed as per the manufactures recommendations. (for mullions and bend at lintel level )

NS 16.1 - 10mm dia re-bar 110 mm depth

NS 16.2 - 12mm dia re-bar 120 mm depth

NS 16.3 - 16mm dia re-bar 160 mm depth

NS 16.4 - 20mm dia re-bar 200 mm depth

NS 16.5 - 25mm dia re-bar 250 mm depth

NS 17.1 - 100 mm dia upto depth 150mm

NS 17.2 - 150 mm dia upto depth 150mm

NS 17.3 - 100 mm dia upto depth 300mm

NS 17.4 - 150 mm dia upto depth 300mm

NS 18 - Providing and fixing of 12mm thick frameless clear toughened glass with automatic bi-parting sliding door operator for clear opening size of 2000 mm x 2400mm, modular design, including internal cover, eagle sensors on both side, Electromechanical lock,light barriers and programme switch complete, With Operator Dimensions (Lx H xT): 4150x 100 x 180 mm. The track profile should be separate from the main profile for enabling reduction in vibration. It should be equiped with Microprocessor controlled control unit. It should be Selflearning, with adjustable parameters for opening and closing speed, hold-open time and opening and closing force; complete in all respect and approved by Engineer-in-charge.

NS 19 - Providing and fixing stainless steel ( Grade 304) railing with 10 mm thick toughened GLASS of height 735mm , supported on 40X40mm Hollow tubes SS 304 grade top mounted square baluster with glass holding accessories ( wall thickness 1.5mm) with two no high tension anchor & fastners , etc. and 50mm dia SS 304 grade hand rail ( wall thickness 1.5mm) including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge.

NS 20 - Supply and installation of full height Single glazed partition using 10mm thick toughened Glass fixed with proprietary anodized aluminium sections of size 26x30mm (H) on top, bottom, horizontal & vertical. Rate to include required accessories as per the manufacturer's specifications and shall be inclusive of all accessories like Gaskets. Glass to glass joints to be sealed with Double sided 2mm Thick transparent tape. The glasses to be butt jointed with 2 to 3mm edge chamfer & edge polishing all around.Achieving value of 31 dB. ( Rate is not included for door frames). Finish - Black Anodised, Partition Height - 2400mm, System - Micra I. Glass - 10mm Toughened Glass, Make - Liko-s or equivalent

NS 21 - Providing and fixing of 12mm thick laminated wooden flooring with double locking system on 3mm thick foam for noice reduction. Wooden planks having mehlamine impregrated decocrative film of HDF density ( water & fire resistant ) to be laid complete in all respect as manufacturers specification and as per direction of Engineer-in-charge.

NS 22 - Providing and fixing 8mm thick High pressure laminated (HPL) wall cladding as per specification given below • Black Paint on Plastered Wall. • Fix aluminium section on wall, maintain gap of 400 - 700mm center to center with help of cleat vertically. • Pilot hole must be pre- drilled before fastening rivets tight. • Size of rivets must be three times the thickness of panel and gauge of aluminium. Ensure rivets used are fully threaded.

NS 23 - Providing and fixing Aluminiuml Clip in Metal Ceiling System of600x600/ 300x1200 & more module which includes providing and fixing 'C' wall angle of size 20x30x20 mm made of 0.5 mm thick pre painted steel along the perimeter of the room with help of nylon sleeves and wooden screws at 300 mm center to centre, suspending the main C carrier of size 10x38x10 mm made of G.I steel 0.7 mm thick from the soffit with help of soffit cleat 37x27x25x1.6 mm, rawl plugs of size 38x12 mm and C carrier suspension clip and main carrier bracket at 1000 mm c/c. Inverted triangle shaped Spring Tee having height of 24 mm and width of 34 mm made of Gl steel 0.45 mm thick is then fixed to the main C carrier and in direction perpendicular to it at 600 mm centers with help of suspension brackets. Wherever the main C carrier and spring T have to join, C carrier and spring T connectors have to be used. All sections to be galvanized @ 120 gms/sqm (both side inclusive), fixing with clip in tiles into spring T with : AluminiumI Metal Ceiling Clip in plain Beveled edge global white color tiles of size 600x600/300x1200 & more etc and 0.5 mm thick with 25 mm height, made of AluminiumI sheet 60 microns (minimum)

NS 24 - Supply and Installation of polycarbonate multi-layered system, a complete assembly of extruded multilayer UV protected polycarbonate panels incorporated into a complete system. Co-extruded UV protected polycarbonate panel system of min 18 mm thick panel of 1050-1200 mm width for bigger spans and minimal junctions for better performance. Panels shall have minimum seven layers with all fixing accessories to ensure best performance for wind uplift, vibration, oil canning and visual appearance. Panels shall be manufactured with vertical offset standing seam at both sides of the panel. Panels shall provide angular daylight for better shading and variable day light transmission throughout the day with translucent and opaque combination of layers. Panels have to be fixed on Purlin with snap on connectors with grip lock locking mechanism and will be secured on MS structure (will be paid Separately) with 3 numbers self-drilling screws & trapezoid SS fasteners holding the base of the standing seam offering best stability having a pull-out load of min. 7000N (7KN) tested as per ISO 6892:1998 and IS 1608: 2005. Panels must satisfy Dart drop impact test as per IS 14443-97 shall show no sign of breakage on Polycarbonate Panel which have been exposed to UV for a min. of 500 Hours as per ASTM G 155. Panels shall not have Yellowness Index as per ASTM D 1925 of 15 units when tested on a sample exposed to UV for 500 Hours as per ASTM G 155. U value shall not be more than 1.8 W/m2K as per EN ISO 10077-2:2018. Panel shall be with additional End cap/Aluminium U/F profile/ Glazing Bar for ends as required. Panel shall be fixed over MS structural steel/MS purlin (paid separately) conforming to the detail technical specifications as per approved architectural drawings. Trained and factory authorized labour with supervision to complete the entire panel installation as per drawing & direction of the engineering in charge. Color: As per Approval. Approved Make: DPI Daylighting/ GE/Lexan/Dunpolan

NS 25 - Providing and fixing 'Unistone/Unique', make or equivalent Glass Reinforced Concrete (G.R.C) Screens casted with 'Spray Mix' concrete design in approved size, pattern, thickness of 50mm on the outer Border & 25-30mm for Internal member and shade. The Screens should be made from ‘53 grade’ White Portland Cement manufactured by ‘JK Cement’ or 'Birla white', White Quartz fine graded sieved Silica Sand, Alkali Resistant Glass Fibre manufactured by 'NEG Japan, Owen Corning ‘Saint Gobain’ or equivalent, Super Plasticizers manufactured by ‘Karochem’ or equivalent, Polymers manufactured by ‘Nova Polychem’ or equivalent and U.V resistant Synthetic inorganic pigments should be used for pigmentation manufactured by ‘Phenochem industries or equivalent. The Screens casting shall take place with layering methodology using- Direct Power Spray machines. The GRC Screens flexural strength average L.O.P should be above or equivalent to 6 N/mm2 & M.O.R should be above or equivalent to 15 N/mm2 for tests done on 28 days cured samples. The fixing of Screens should be done using ‘Dry fixing’ method onto structural support members i.e. R.C.C, Brick work, MS Framework. SS / MS Galvanized CLAMPS & PINS also if required fasteners to be used of Wurth, Hilti & Fischer or equivalent. ALL CAST IN SOCKET TO BE EPOXY PRIMER COATED. ELECTRODES to be used of ADVANI, MANGALAM, ESAB or Victor brand or equivalent. Vendor shall submit shop drawings of same, the drawings to be duly approved from Engineer in charge at site

NS 26 - Providing and applying water proofing treatment for landscaping decks after cleaning, brushing and removing loose materials & filling pot holes /cracks by using polymer modified cement mortar using Dr. Fixit pidicrete URP and (i) Applying Dr. Fixit Flexi 270 (I) or equivalent pure polyethrene based single component, low VOC, elastomeric, seamless waterproofing membrane, applied in 2 coats over one coat of primer at a total consumption of minimum 1.8 kg. sqm to achieve a DFT of 1.5mm & thereafter providing & laying 120 GSM polyster geotextile layer. (ii) laying protective concrete screed of average thickness 75mm using M25 grade of concrete with minimum thickness of 40mm at rain water outlet at a slope of 1:120, making wattas at junction of horizontal & vertical surfaces to float finish well compacted curing for 7days etc complete ( concrete to be paid extra) (iii) Supply and installtion of “Tikidan” / "Uniseal / Delta Terraxx" Rolled Matrix Soil Filter cum surface drainage System as per manufacturers specifications. “Tikidan"/ "UNiseal", or, “Delta Terraxx” consist of dimple raised, moulded polypropylene sheet bonded to a high strength polypropylene geotextile fabric. This geotextile fabric composite allows passage of moisture through fabric while preventing fine soil from entering to drainage channel all complete as per direction of Engineer-in-charge

NS 27 - Providing and fixing Jaquar/parryware/hindware/Cera make table mounted quarter turn sink cock as per Jaquar make model Florentine FLR-CHR-5357N complete for all respect.

NS 28 - Extra for providing PVC sleek dual flush cistern instead of cistern taken in item no 17.1.1 (CIVIL WORKS)

NS 29 - Providing and fixing oval shaped under counter wash basin of Jaquar/Parryware/Hindware/Cera make size 595x 420x 200 as per Jaquar make model (CNS-WHT-705) and Jaquar/parryware/hindware/Cera make 15mm dia CP Brass auto closing pillar cock as per Jaquar make model (PRS-CHR-301) and 32mm Jaquar/Parryware/ Hindware / Cera make CP waste coupling including painting of fitting and cutting and making good walls wherever required.

NS 30 - Providing and fixing towel ring of Hindware/ cera /Jaguar make as per Jaquar make model (Cat CAN-CHR-1121BN) complete in all respect.

NS 31 - Providing and fixing in floor and wall face Ringfit PVC Conventional system for soil and waste water pipes conforming to (HSN CODE: 3917) Type B including jointing with seal ring. (i) Single socketed pipes. 160MM

NS 32 - Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC pipes including jointing with seal ring leaving 10 mm gap for thermal expansion. Providing & fixing UPVC Coupler 160mm dia

NS 33 - Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC pipes including jointing with seal ring leaving 10 mm gap for thermal expansion. Providing & fixing UPVC Bend 160mm dia

NS 34 - Providing and fixing dry cladding upto 10 metre heights with 25mm thick gang saw cut stone with (machine cut edges) of uniform colour and size upto 1mx1m, fixed to structural steel frame work and/ or with the help of cramps, pins etc. and sealing the joints with approved weather sealant as per Architectural drawing and direction of Engineer-in-charge. (The steel frame work, stainless steel cramps and pins etc. shall be paid for separately) : 25 mm Ruby Red Granite (Polished) with base price of ₹ 2250/sqm and finishing the joints with tanex and pigment.

NS 35 - NS 35 - Design ,supply and installation 500 LPH Reverse RO Plant with treated water quality as stated below Turbidity : < 1NTU pH : 6.5-7.0 Chlorides : <10 ppm Sulphates : <5 ppm TDS : < 150 ppm and RO plants should consist of equipments as stated below:

I. RAW WATER FEED PUMPS 1. Type : Centrifugal Mono block 2. Discharge in m3/hr : 1.5 m3/hr 3. Discharge Pressure : 2.0-3 Kg/ sq.cm 4. Total Head in Meter : 20-30 m 5. Rating in HP/kW : 0.5HP/KW 6. Material of Construction: CI 7. Casing : SS 8. Impeller : SS 9. Phase : 3 Phase 10. Quantity : 2 nos.

II. SAND MEDIA FILTER 1. Design Flow : 1.5 m3/hr 2.Type of vessel : Vertical Cylindrical 3. Type of Flow : Down flow 4. Size : 10”x54”(2.5” Top) 5. Operating Pressure : 3.0Kg/ sq.cm 6. Material of Construction: FRP 7. Media : Various Sizes of Sand & pebbles 8. Qty of Sand : 30 Kgs 9. Quantity : 1 nos.

III. ACTIVATED CARBON FILTER 1. Design Flow : 1.5 m3/hr 2.Type of vessel : Vertical Cylindrical 3. Type of Flow : Down flow 4. Size : 10”x54”(2.5” Top) 5. Operating Pressure : 3.0Kg/ sq.cm 6. Material of Construction: FRP 7. Media : ACTIVATED CARBON IV900 8. Qty of Anthracite : 30 Kgs 9. Quantity : 1 nos.

IV. ANTISCALENT DOSING SYSTEM 1. Type : Electronic Dosing Pump 2. Capacity : 0-6 LPH 3. Operating Pressure : 4Kg/ sq.cm 4. MOC : PP 5. Power Supply : 230v A.C. 50 Hz 6. Make : Droplet 7.Qunatity : 1 no. Tank 8. Capacity : 100 ltr 9.MOC : HDPE 10.Qunatity : 1 no.

V. MICRON CATRIDGE FILTER 1. Type : Spun/Wound 2. Model : 5 micron as suitable 3. MOC : PP 4. Quantity : 2 Nos. 5. MOC : PP

VI. LOW PRESSURE SWITCH 1. Pressure : 0.5-5kg/cm2 2. MOC : Glass Filled Nylon 3. Quantity : 1 Nos.

VII. HIGH PRESSURE SWITCH 1. Pressure : 2 -25kg/cm2 2. MOC : Glass Filled Nylon 3. Make : DANFUS 4. Quantity : 1 Nos.

VIII. HIGH PRESSURE PUMP 1. Type : Vertical Multistage Centrifugal 2. Discharge in m3/hr : 1.8 m3/hr 3. Discharge Pressure : 12-13.5 Kg/cm2 4. MOC : CI body, SS impeller 5. Phase : 3 Phase 6. Motor rating : 1.1 KW / 1.5 HP 7. Quantity : 2 nos.

IX. FRP MEMBRANE HOUSING 1. MODEL : 4040-300PSI 2. Quantity : 2 Nos.

X. MEMBRANE 1. Membrane : DOW FILMTECH 2.Quantity : 2 nos. 3. Orientation : 01:01:00 4. Model : BW4040.

XI. FLOWMETER 1. Type : Rota meter Type 2. Quantity : 2 Nos.

XII. PRESSURE GAUGE 1.Type : Glycerin Filled 2. Range : 0-21kg/cm2 3.Quantity : 2 nos. 4.Range : 0-7Kg/cm2 5.Quantity : 2 nos.

XIII. UV STERILIZER SYSTEM 1. Model : ECS15L 2. Flow Rate : 750LPH 3. Inlet Outlet Size : ¾ BSP 4.Reactor Chamber MOC : SS304 5.Operating Voltage : 230V/ 50-60 Hz (+-10%) 6.MOC : Alfa UV

XIV. OZONATOR 1. Model : D2GRM 2. Generation Rate : 2 Grm/Hr 3. Technology : Corona Discharge 4. Cabinet MOC : MS Body 5.Operating Voltage : 30V/ 50-60 Hz (+-10%) 6.Operating watts : 80W

XV.PIPING 1. RO SKID : As per requirement with SS202 HD 2. High Pressure Piping : As per requirement with uPVC pipes 3.Low Pressure Piping : Interconnecting piping, fittings, and valves within the battery limits of the Water Treatment plant with uPVC pipes.

XVI. ELECTRICAL ITEMS 1. Control panel : Khayatee III Phase 2. G.I perforated cable tray & copper cables

XVII. SS Tank 1000 ltr. SS Tank with Six Layer insulation. Lock Latches, Big manhole, reinforced heavy wall corrugation, ss 304 water inlet outlet, water level controler having multiple level (L & T), Easy Drainage, Sediment Drainage pipe, SS Bulkhead fitting, Lifelong durable and leakproof, 100% recycle, Non Toxic, rust free and scaling free, SS 2205 Duplex Innner Sheet, Havey Duty SS 304 Stand, Dual protection coating with reflective insulation at bottom, pressurized tanks are teasted for 50 kg for whole life leakage. Cutomize inlet and ourlet scope, Full Volume guaranteed, all insulation made in Germeny and Italy-Certificate provided, Factory Acceptance test certificate provided- make Oasis

Full job of 500 Lph RO including ss tank and installtion as stated above

NS 36 - Supplying, installation, testing & commissioning of wall hanging drinking online water cooler with bottle filler facility sensor and Mechanical both operation, made by stainless steel top and heavy duty galvanized steel frame. With cooling capacity 60 ltr, ADA Compliant, size 472 mm Depth X 447mm width X 960mm, SS bubbler guard , operated between 50 to 120 PSI, Chiller unit Suitable to R134a Refrigerant, Adjustable thermostat control, suitable for 220-230v/50-60 hz A/C Supply Complete with all accessories which include MD-CU29 Push Pad,, which is an EPA registered antimicrobial copper that fights off microorganisms which include MRSA and e-coli. The water Fountain shall possess NSF-USA, TUV, GRIHA-Green building, energy star saving certification, Mechanical + Sensor Both Operation and to be placed at different location of buidling. installing the Water Fountain for proper functioning and aesthetic view as directed by the engineer-in-charge without any extra cost- Make- Oasis/Sunrock/Filtrin/Eureka Forbes

NS 37 - Supplying and installation and commissioning of sump pump model 2200CW, 3 Phase, approx capacity 5LPS at head 9.5m with provision of auto and manual starter and delivery pipe of 65mm complete. (Kriloskar,CRI, GE, Crompton)

NS 38 - Supplying and installtion of Water Transfer Pumps (Hydropneumatic systems) 1-nos, vertical stainless steel in-line pumps having stainless steel casing, stainless steel pump foot diffusers, stainless steel impellers, ceramic bearing, tungsten carbide shaft protection bushes and mechanical seal driven by appx 25.0 hp ,415volts 50 cycles, AC 3 phase TEFC vertical flange motor motor. Each pump shall be capable of delivering 12.0 lps @ 100 mtr head. With complete headers, fittings & foundation as per Specifications

NS 40 - Supplying, installing, testing & commissioning of Sewage Treatment Plant of 50m3/day based on MBR technology (excluding excavation, back filling & disposal of surplus earth MS / Civil construction work) for the following duty: Nature of Sewage - Domestic Sewage from toilet, kitchen , Bathrooms & pantry waste water shall be discharged into the STP. Design to take consideration of same.

The STP shall be designed based on the following parameters: Daily average flow : 50m3/Day PH : 6.5 - 8.5 BOD5 : 250 - 300 mg/l S. Solids : 50 - 350 Mg/l COD : 600 - 800 mg/L Oil & Grease : 50-100 mg/L

Effluent discharge standard after treatment :- PH : 6.0 - 8.5 BOD5 : less than 5 mg/l S. Solids : less than 5 Mg/l COD : less than 50 mg/l Oil & Grease : less than 5 mg/l

Note: STP vendor will be responsible for getting approval / NOC from concerned pollution control department of state government at various stages of works including preparation of report/drawing as per pollution board requirement. Contractor shall include the cost of chemicals consumed during testing & commissioning . No extra cost will be paid to the vendor for getting the approval. Client will be liable to pay valid statutory fees payment against receipt of invoice. S.T.P comprises of following equipment as stated below:

A. Electro - Mechanical Equipment

1. Bar Screen : Supplying, installing, testing & commissioning Perforated bar screen chamber including 2nos. S.S. bar screen of size having provision for lifting arrangement etc. complete as required. Size : 300mm X 300mm MOC : SS-304 Purpose: For separation of large solids

2. Supply, Installation, Testing & Commissioning of Automatic fine screen system including all necessary equipment and lifting arrangement complete as required.

3. Supply Installation Testing & commissioning of Oil skimmer capacity and size for removal of oil from chamber in all respect.

4. Supply, installation, testing & commissioning of 1 Nos Stainless Steel Perforated, Corrugated Basket type fine screen with suitable lifting arrangement of following sizes : (size 300 mm wide x 300 mm high approx). - Domestic Sewage (Location before reaction tank)

5. Water level controller for operation of the system connected to control panel for automatic switching ON / OFF of each pump.

6. Supply, installation, testing & commissioning of non clogging type Submersible Sewage Pumps having CI casing & CI impeller complete with foundation bolt and all accessories, motor of required capacity. pressure gauge on delivery line with isolation cock, level controller to control the level for provision to control the level of sump automaticly. Pumps shall have following duty:2No.(1W+1S) Flow Rate : 3 cum/Hr Head : 10mtr Solid handling : 32MM Make:Wilo/Grundfos Purpose: For sewage transfer from equalisation tank to Aeration Tank

7. Supply, installation, testing & commissioning of non clogging monoblock type Sludge Recirculation Pump having CI casing & CI impeller complete with and foundation bolts all accessories, motor of required capacity. pressure gauge on delivery line with isolation cock, level controller to control the level of sump automatically. Pumps shall have following duty: Flow Rate : 2 cum/Hr Head : 10mtr Solid handling : 8mm Make: Kilosker/KSB Purpose: For transfer sludge to Sludge holding tank and recirculation to Anoxic chamber of Aeration tank

8. Air diffusion system shall include the following:

8(a) 2 Nos. twin type Rotary air blowers (1W + 1S) capable of delivering 50m3/hr of free air at 0.5 kg/cm2 driven through “V” belt or directly coupled through flexible coupling to a TEFC motor of suitable HP Suitable for 415 ± 10% volts, 3 phase, 50 cycles A/C supply. Including foundation and foundation bolts work. Purpose: For air supply to equalisation tank/sludge holding tank/Aeration Tank

8(b) 2 Nos. twin type Rotary air blowers (1W + 1S) capable of delivering 70 m3/hr of free air at 0.5 kg/cm2 driven through “V” belt or directly coupled through flexible coupling to a TEFC motor of suitable HP Suitable for 415 ± 10% volts, 3 phase, 50 cycles A/C supply. Including foundation and foundation bolts work. Make: Everest/Beta Purpose: For air supply to MBR Reactor

9. Supply, Installation, Testing & Commissioning of Variable frequency Drive (VFD) to regulate blower's motor speed with in all respect Purpose: To MBR blower Regulate

10. Non clog, Self Cleaning type air dispersion system capable of handling 3-5 cfm of air with oxygen transfer efficiency of 3-4% per / meter water depth. Air dispersion grid shall be assembled in modular form so that they can be replaced / repaired easily from plat form at the top. Purpose : Air dispersion system shall be provided for transfer to air in Sewage Sump/equalisation tank, aeration tank and Sludge Holding Tank.

11. Solenoid Valves are required in air line of MBR to make the system automated according to the process cycle. Purpose : Air dispersion system shall be provided for transfer to air in MBR Reactor.

12. Providing and fixing all piping (as described below) and isolation control valves for making the system complete. uPVC : Submerged air piping MS Epoxy : Air piping & pumped effluent riser (non-submerged) MS Epoxy : Interconnecting pipe line after delivery header of pump/ filter MS epoxy : Pumped effluent (submerged) & tank overflow pipe line Make: (For MS Pipe)--Tata/Jindal

13. Supply, installation, testing and commissioning of MBR Module Hollow Fibre/Flat sheet to be installed in MBR reactor alongwith suitable sludge removal arrangement either by pumps or air lifting pumps. Make:Toray/GE Purpose: For bacterial growth on surface

14. Supplying, installing, testing & commissioning of Horizontal centrifugal non clog water pumps with CI casing and CI Impeller along with motor, pressure gauge with isolation cock, Isolation valve, NRV on delivery line. Isolation valve, stainer (with by-pass) at suction. Mechanical seal, suitable vibration elimination pads of approved design, drain pipe with valve for the pump. The pump shall be suitable for 415±10% volts 3 phase AC supply. Including foundation bolts(1 Working + 1 Standby)

15. MBR Suction Pump Capacity : 3 cum/Hr Head :10Mtr Make : Kirlosker/Wilo Purpose: For deliver MBR treated water to Treated water tank

16. Treated Water Transfer Pump Capacity : 4.2 cum/Hr Head :25Mtr Make : Kirlosker/Wilo Purpose: For transfer treated water to desire purpose

17. Supplying, installing, testing & commissioning of non clog Submersible type Plant Room Sump Pumps with CI Head & Base, CI Impeller along with motor, pressure gauge with isolation cock, Isolation valve, NRV on delivery line. Isolation valve, stainer (with by-pass) at suction. Mechanical seal. The pump shall be suitable for 415±10% volts 3 phase AC supply. Capacity: 4 cum/hr Head: 10-12mtr Make:Wilo/Grundfos Purpose: For transfer of Plant room drained water

18. Supply, installation, testing & commissioning of Poly dosing system comprising of 100 ltrs HDPE/FRP tank with 0-6 lph electronic metering type pump.

19. Supply, installation, testing & commissioning of Chlorine dosing system comprising of 100 ltrs HDPE/FRP tank with 0-6 lph electronic metering type pump. Purpose: For Disinfection purpose

20. Suppy, installation, testing & commissioning of electro-mangnetic type flow meter at inlet of reactor tank. Size 40mm

21. Suppy, installation, testing & commissioning of DO & Turbidity analyser fitting in all respect.

22. Supply Installation Testing Commissioning CIP System Chemical dosing should consist of electronic / electro mechanical metering pumps with suction and delivery flexible connections and fittings. The pump shall be mounted on HDPE tank of 500 ltr capacities. Pump Flow :- 5 cum/Hr Head :- 25 meter Make : Wilo/Grundfos

23. Supply Installation Testing & Commissioning of submesible Mixer of required capacity for anoxic tank in all respect lifting arrangement. Make : Toshio Purpose : For completion of chemical reaction effectively

24. Supply, Installation, Testing & Commissioning of ozonator unit shall have with oxygen consitrator, recirculation pump, SS ventury, pipe line, control panel etc complete.

25. Supply, installation, testing and commissioning of Filterpress with 12"X12" with 11 no plates with all fittings & accessories .Hydraulic operated. Purpose: For Drying of Sludge

26. Supply, installation, testing and commissioning of Filter Press Feed Pumps Screw type Complete with all fittings & accessories. Including foundation and foundation bolts.( 2Nos.- 1W+1S) Capacity :1cum/H Head : 40mtr MOC : CI Purpose: For feed of sludge to Filter Press

B. Electrical installation for Sewage treatment plant

2. MCC –1 (Sewage Treatment Plant)

Bus Bar: 50 amps TPN (25 KA) aluminium bus bar with heat shrinkable insulation sleeves

h. Spare MCB’s of following capacities: i. 20 amps TPN MCB’s 2 Nos ii 32 amps TPN MCB’s 2 Nos

MCC –1 for STP as described above

4. Note: All MCCB's to be suitable for motor duty and shall be of 25 KA breaking capacity. Provision shall be made for providing potential free contacts to all pumps starters for connection to building automation system. All motor starter shall be provided with Automatic level controller. Overflow alarm must be provided at the plant room Electrical panel must have the Auto announciator to indicate the system failure if any.

Full job of STP ( Electro- mechanical equipment & electrical installation ) as stated above

NS 41 - Supplying and providing Electric rotary type Lawn Mower With Grass Catcher - 18" Blades - 1 PH AC Adapter Push Lawn Mower complete

NS 43 - Providing, fitting and fixing of foldable horizontal Grab Bar of stainless steel (Make Jaquar, Kitch or equivalent) for person with disabilities (for WC)

NS 44 - Providing, fitting and fixing of vertical Grab Bar of stainless steel (Make Jaquar, Kitch or Equivalent for person with disabilities. (for wash basin & WC)

NS 45 - Providing, and fixing of C.P grating 100mm

NS 46 - Supplying fabricating and installation of green wall consisting of MS frame steel structure with primere & paint including vertical wall panel 450x150 mm approx to hold 3 nos. of 150mm pots providing for drip irrigation with 16mm irrigation pipes which is to be installed aling with the drips for each pot with filter. Pots would be installed with geotextile fabric filled with engineered soil consisting of cocopeat and vermicompst. 3 nos. storage tank with pressure pump having capacity of 3000 Ltrs each shall also be supplied and installed. suitable plants will be supplied and planted as per clients choice. The rate includes all materials and labour etc. complete in all respect as given in specification and as per direction of Engineer-in-charge.

Fire Fighting

NS 47 - Supplying and installing Air Release Valve, Gunmetal, having rubber ball with 1” (25mm) BSP Male threaded inlet

NS 48 - Supplying and installing Fire Hydrant Valve, Double headed, Gunmetal, IS:318-LTB2 Grade, 100mm N.B Flanged inlet, Brass Spindle, 02 individually controlled 63mm Female Instantaneous Oblique Outlet, Complete with PVC Blank Cap & GI Chain, Bearing IS:5290 Mark, Flange O.D.220mm, PCD 180mm, Eight 19mm Dia Holes

NS 49 - Supplying and installing Fireman Axe-made of carbon steel with rubber insulated handle tested to 20,000 Volts as per IS:926

NS 50 - Supplying and installing Fire shaft door fabricated out of M.S. sheet and frame, door size of 1200 (W) x 2100 (h) with 4 mm thick glass, suitable Rubber beading and Locking arrangement and complete door shall be powder coated with red color powder coating

NS 51 - Providing, storing, handling, shifting, installation, testing and commissioning of halon free portable fire Extinguishers as described below:

NS 51.1 - Co2 type Fire Extinguisher 4.5 Kgs. Capacity, made from brand new seamless cylinder, as per IS: 7285 and CCE approval, fitted with Discharge hose and horn and wheel type valve with initial Charge as per IS: 15683:2018 specification, bearing ISI Mark & as approved. by Engineer-in-charge.

NS 51.2 - Co2 type Fire Extinguisher 6.5Kgs. Capacity, made from brand new seamless steel cylinder, as per IS: 7285 and CCE approval fitted with discharge, hose and horn with wheel type valve mounted on trolley wheels with initial charge as per IS: 16018 : 2012 specification, bearing ISI Mark & as approved. by Engineer-in-charge.

NS 51.3 - Co2 type Fire Extinguisher 9 Kgs. Capacity, made from brand new seamless steel cylinder, as per IS: 7285 and CCE approval fitted with discharge, hose and horn with wheel type valve mounted on trolley wheels with initial charge as per IS: 16018 : 2012 specification, bearing ISI Mark &as approved. by Engineer-in-charge.

NS 52 - Providing and fixing Fire related signages printed on photoluminescent U1000 aluminium sheet of 1.0 mm (+-10%) containing Lumigen II as base chemical, covered under UV stablized coating and of appropriate size including fixing on wall, door, ceiling etc. with proper clamps, hangers, cleats, anchor fasteners etc. complete in all respects as directed by Engineer-in-charge.

NS 53 - Providing and fixing FRP Hose Box single door (750X600X250)

NS 54 - Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc

NS 54.1 - 4 Core X 16 sqmm. Aluminium Armoured

NS 54.2 - 4 Core X 10 sqmm. Aluminium Armoured

NS 54.3 - 3.5Core X 50 sqmm. Aluminium Armoured

NS 54.4 - 3.5 Core, X 35 sqmm. Aluminium Armoured

NS 54.5 - 3.5 Core X 300 sqmm. Aluminium Armoured

NS 54.6 - 3.5 Core X 120 sqmm. Aluminium Armoured

NS 55 - Supplying , installating, Testing & commissioning of XLPE insulated & PVC sheathed 1.1 KV grade armoured Copper control cables for various equipment through walls / ceilings with appropriate clamps / fixing arrangements and complete with termination as per manufacturer's specifications & as directed by Engineer-in-charge.

NS 55.1 - 6 C x 2.5 Sqmm

NS 55.2 - 2 C x 4.0 Sqmm

NS 55.3 - 2 C x 2.5 Sqmm

NS 56 - Supply and fixing in position 1 m wide Insulation mat made of elastomeric polymers Material (Class -A) of 415V grade as per IS 15642-2006 . Thickness of insulation mat shall be not less than 3 mm to withstand 1.1 KV dielectric strength AS PER IS 15652 : 2006. It should be complete as per specifications & directions of Engineer-in-charge. It should be complete as per specifications & directions of Engineer-in-charge.

NS 57 - Providing and fixing 100x100x100 mm single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.

NS 58 - Providing and fixing 75x75x75 mm single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. Hubless centrifugally cast (spun) ironepoxy coated inside & outside as per IS:15905

NS 59 - Providing and fixing CI W.C CONNECTOR (PUSH-FIT) complete Hubless centrifugally cast (spun) ironepoxy coated inside & outside as per IS:15905

INTERNAL AND EXTERNAL ELECTRICAL

NS 60 - Supplying and fixing 63 amps, 415 volts, TPN industrial type, socket outlet, with 4 pole and earth, metal enclosed plug top along with 63 amps "C" curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

NS 61 - Supply & fixing of PVC raceways for following sizes with all accessories like coupler,bends,risers and fixing brackets along with covering complete in all respect equivalent to Legrand Model 0896

NS 61.1 - 100 mm X 38 mm, 2 Compartment PVC Race ways

NS 61.2 - 100 mm X 38 mm, 2 Compartment PVC Race ways

NS 62 - Supply & fixing of GI raceways for following sizes with all accessories like coupler,bends,riser and fixing brackets along with covering complete in all respect equivalent to Legrand Model 0895

NS 62.1 - 100 mm X 38 mm, 1 Compartment GI Race ways

NS 62.2 - 150 mm X 38 mm, 1 Compartment GI Race ways

NS 62.3 - 225 mm X 38 mm, 3 Compartment GI Race ways

NS 63 - Supply & fixing of GI raceways for following sizes with all accessories like coupler,bends,riser and fixing brackets along with covering complete in all respect equivalent to Legrand Model 0895

NS 64 - Supply and fixing of GI Floor Box with 3 Compartments (264X264 mm) height 86 mm with Cover with and provision of cable entry complete in all respect equivalent to Legrend Model 6896

Down Lighter

NS 65 - SITC of recess mounting round 6 Watt LED Down Lighter having Powder coated die cast aluminium housing with efficacy ≥100 lm/w with heat sink, diffuser/ Reflector and driver set complete in all respect.

NS 66 - SITC of LED Wall bracket Luminaire with E27 base lamp holder suitable for LED bulb of wattage 12W with chrome lamp cup.

NS 67 - SITC of recess mounting round 12 (± 10%) Watt LED Down Lighter having Powder coated die cast aluminium housing having efficacy ≥ 100 lm/w with heat sink, diffuser/ Reflector and driver set complete in all respect.

NS 68 - SITC of recess mounting round 18 (± 10%) Watt LED Down Lighter having Powder coated die cast aluminium housing having efficacy ≥ 100 lm/w with heat sink, diffuser/ Reflector and driver set complete in all respect.

For Double height

NS 69 - SITC of recess mounting round 24 Watt (± 10%) LED Down Lighter having Powder coated die cast aluminium housing having efficacy ≥ 100 lm/w with extended heat sink, diffuser/ Reflector and driver set completed in all respects.

2'X2' Square Fittings

NS 70 - SITC of 36 Watt (± 10%) indoor Recess mounting LED Square Fitting for Armstrong Ceiling having Powder coated die cast CRCA housing body having efficacy ≥ 100 lm/w with extended heat sink and diffuser of and driver set complete in all respect.

LED Tube Light

NS 71 - SITC of LED Tube Light with batten suitable for up to 20 watt (± 10%) watt LED tube light fitting with housing made of polycarbonate on Surface complete in all respect

NS 72 - SITC of LED Tube Light with batten suitable for up to 40 watt (± 10%) LED tube light fittingwith housing made of extruded aluminium on Surface complete in all respect

NS 73 - SITC of IP65 10 Watt LED bulkhead luminaire (± 10%) made of pressure die cast aluminium with driver set having efficacy ≥ 100 lm/w and above Protection complete in all respect.

NS 74 - SITC of factory wired integral LED flood light luminaires with pressure die cast aluminium housing built with dirver set suitable for 80 Watt (± 10%). Confirming to IP 65 protection complete in all respect.

NS 75 - SITC of Mirror Wall Light oblong 10 Watt (± 10%) LED luminaire with driver set confirming to IP 65 and above Protection having polycarbonate housing complete in all respect.

NS 76 - SITC of LED cover strip 5W/Meter comes in 5 meter spool along with driver with copper wiring for looping

NS 77 - SITC of Specialized 20 watt LED Track lighting system for Museum alogwith with sensors required and 1 meter track light accessories etc and housing made of pressure die cast aluminium wirh reflector complete in all respect.

NS 78 - SITC of double sided illuminated exit sign with system wattage 8 watt LED including providing maintenance free batteries & charger capable of working for 2 hr duration mounted on ceiling/wall complete with the approved EXIT self adhesive labels as per site requirement as required including connection with 1.5 sqmm FRLS PVC insulated copper conductor.

NS 79 - Supplying, erection, connecting, testing and commissioning of 750 mm wall circulating fan complete in all respect including fixing wiring connection etc

NS 80 - Supplying, erection, connecting, testing and commissioning of 400 mm wall fan complete in all respect including fixing wiring connection etc

NS 81 - Supplying, erection, connecting, testing and commissioning of following size exhaust fan complete with gravity louver and connection with 3 core flexible wire as required.

NS 81.1 - 380mm 900 RPM

NS 81.2 - 450mm 900 RPM

NS 82 - SITC of single unit LED aviation obstruction light complete with transformer and LED spiral etc complete in all respect..

NS 83 - Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.

NS 83.1 - S & F 100 amp. FP MCCB (16KA) Thermal Magnetic Release

NS 83.2 - S & F 125 amp. FP MCCB (25KA) Thermal Magnetic Release

NS 83.3 - S & F 160 amp. FP MCCB (25KA) Thermal Magnetic Release

MAIN LT Panel

NS 84 - Supply, erection, testing & commissioning of IP -42 cubicle type Panel fabricated (folded joints construction) out of 14 SWG CRCA sheet steel floor mounted totally enclosed extendable on both sides switchboard of uniform width with top cable entry and suitable for use on 415 V, 3 phase 4 wire 50 c/s having 50 KA fault capacity complete and housed with incomming and outgoing aluminium bus-bars,interconnection between feeders etc. and their accessories including supply and fixing of base channels of 100x50x6mm as required with provision for following incoming and outgoing switchgear with protection, metering etc. and terminals for scheduled cables and also compataible to PC/PLC/BMS with communiction port RS-485, complete as required and as per specification and schematic diagram complete as required. confirming IS 61439

Note-1) DESIGN, TESTING & CERTIFICATION OF LT MAIN PANEL's MUST COMPLY IEC-61439, ALONG WITH IEC-61641 FOR INTERNAL ARC FLASH

2) PROVISION OF BUSDUCT/CABLE MUST BE AS PER SLD.

The incoming of Transformer feeders & DG feeders as shown on drawing shall be connected through bus duct. The suitable adopter box shall be provided on top only and Solar Incommer through cable from bottom.

All Intelligent ACB shall have Micro processor based O/C, S/C & E/F release RS485 on board communication port. The release setting of all ACB's shall be possible from communication & also user can see the energy parameter of release from BMS/SCADA/Webpage and display module/HMI shall be provided on panel for each ACB to see the release data of ACB. All ACB's shall have Ics=Icu=Icw=50KA for 1Sec & should be supplied with Adopter Terminal Connections whose orientation can be changed on site.

All Intelligent MCCB shall have Micro processor based release with RS485 on board communication port, the release setting of all MCCB shall be possible from communication & user can see the release from BMS/SCADA/Webpage and a indication shall be provided on panel for each MCCB . All CTs and PTs shall be cast resin type. All MCCB shall have Ics = 100% Icu & should have Isolation Feature & Class II Front Face as standard.

All Intelligent ACB'S shall have spare wired contacts for ON,OFF,Trip,rackin,rackout spring charge status for BMS/SCADA communication along with LCD display.

All Intelligent MCCB shall be motorised with Microprocessor based release having spare wired contacts for monitoring ON/OFF and Trip shall be provided for SCADA communication. Control: ON & OFF.

TVM Shall have RS 485 Modbus RTU on board Communication protocol for SCADA communication.

All outgoing feeders shall have touch display module/HMI with RS-485 ports

Night mode and day mode for APFC CT in the transformer incomer.

The LT Panel manufacturer shall provide necessary,CT's Aux. contacts; multiply those contacts in the respective panels etc. to hook up in to PLC system

INCOMING

TRANSFORMER INCOMER [2 Nos.] shall be equipped as: (1000 KVA)

1 No. 1600 A, 50KA FP, draw out type electrically operated air circuit breaker with 230 V A.C. spring charged motor and micro processor based O/C, S/C & E/F releases, with communication port through RS-485 compatible with PLC/PC/BMS etc

1 No. 24 volt D.C.Shunt release

1 No. 230 volt A.C.closing coil

1 No. 415 volt A.C. under voltage release.

1 No. 1600 Amp. Ammeter (digital type) with inbuilt ASS

1 Set of CTs 1600 A/ 5A class-1 for metering

1 No.Volt Meter (digital type) with inbuilt VSS & control fuses.

1 No.P.F. meter (digital type)

1 No.KWH meter (digital type)

1 No. C.T.1600/5 / 5A Class-1 for Capacitor panel.

Under Voltage relay 415 V A.C.

Over Voltage relay 415 V A.C.

O/C, S/C, and E/F relay

Breaker control switch

1 Set of phase indication lights R,Y,B.

1set of ON-OFF-TRIP ckt. Healthy. indication lights

Spring charged indication.

D.G. PANEL INCOMERS[2 Nos.625 KVA]

1 No. 1250 A, 50KA FP, draw out type electrically operated air circuit breaker with 230 V A.C. spring charged motor and micro processor based O/C, S/C & E/F releases, with communication port through RS-485 compatible with PLC/PC/BMS etc

1 No. 24 volt D.C.Shunt release

1 No. 230 volt A.C.closing coil

1 No. 415 volt A.C. under voltage release.

1 Set of CTs 1250 A/ 5A class-1 for metering

Digital Tri-Vector meter with KVAR, KW, KWH, PF, Ampere, Volts, Frequency metering

Battery charger 230 V/ 24 V DC, 20 A with DC ammeter and DC voltmeter. Charger should have all basic protections like over load, over Voltage reverse polarity etc.

Under Voltage relay 415 V A.C.

Over Voltage relay 415 V A.C.

O/C, S/C, and E/F relay

Restricted Earth Fault relay

Three phase differential relay

Trip circuit supervision relay

Auxillary relay

Master trip relay

Breaker control switch

Automatic load supervision relay

1 Set of phase indication lights R,Y,B.

1set of ON-OFF-TRIP ckt. Healthy. indication lights

Spring charged indication.

SOLAR POWER PLANT INCOMERS [1 Nos.] shall be equipped as: (50 KWp)

1 Nos.250 A FP MCCB , 50 KA, with M.R.,O/C, S/C & E/F releases & indicating lamps (R.Y.B. Phase indication with ON/OFF & Trip Indication) & ammeter and volt meter with all functions with set of CTs etc

1 No. Ammeter (digital type) with inbuilt ASS

1 No.Volt Meter (digital type) with inbuilt VSS & control fuses.

1 No.8 step A.P.F.C.Relay (intelligent micro-processor based with current sensitivity less than 1%)

3 Nos. CTs- 250/5 Amps. Class -1.0

1 Set phase indication lights (R, Y, B)

BUS BARS:-

2000 Amps. 4P aluminium bus bars (50 KA)

BUS COUPLER:-

1 No. 1600A ,4POLE ,EDO ACB with 230 V A.C. spring charged motor.

1 sets Breaker Control switch

1 Sets of phase indication lights R,Y,B.

1 sets of ON-OFF-TRIP ckt. Healthy. indication lights

Interlocking: Transformer incomers ,DG Panel Incommers,solar PV Plant Incomers and bus couplers shall be electrically and mechanically interlocked so that no different source can be paralled at any point of time.

OUTGOINGS:-

3 Nos.630 A FP MCCB , 50KA, with M.R.,O/C, S/C & E/F releases & indicating lamps (R.Y.B. Phase indication with ON/OFF & Trip Indication) & Multifunction meter with all functions with set of CTs with communication port through RS 485 compatible with PLC/PC/BMS.

1 Nos.400 A FP MCCB , 50KA, with M.R.,O/C, S/C & E/F releases & indicating lamps (R.Y.B. Phase indication with ON/OFF & Trip Indication) & Multifunction meter with all functions with set of CTs with communication port through RS 485 compatible with PLC/PC/BMS.

2 Nos.250 A FP MCCB , 50KA, with M.R.,O/C, S/C & E/F releases & indicating lamps (R.Y.B. Phase indication with ON/OFF & Trip Indication) & Multifunction meter with all functions with set of CTs with communication port through RS 485 compatible with PLC/PC/BMS.

3 Nos.160 A FP MCCB , 50KA, with M.R.,O/C, S/C & E/F releases & indicating lamps (R.Y.B. Phase indication with ON/OFF & Trip Indication) & Multifunction meter with all functions with set of CTs with communication port through RS 485 compatible with PLC/PC/BMS.

PLC Operations

NS 85 - PLC system for Auto mains failure, Auto Load Sharing Management, with Auto Synchronization (For 2 Nos Transformer + 2 Nos.DG Sets + 1 No. Solar Power Panel )

2 Nos. no volt monitors for DG supply

2 Nos. no volt monitors for main supply

1 Nos. no volt monitors for Ongrid Solar Power supply

1 No. PLC Comprising:

PLC (Allen Bradley/ siemens)

5 Nos. Power monitors

PLC rack

Digital input modes

Digital Output modes

EPROM (EP)

Man Machine interface (MMI)

Grafix Software for PLC

1 set mimic (SEM)

Set of Auxiliary relays

Set of indicating lights and push buttons

set of control MCBs

Communication cable from PLC to computer as per requirement

1 No. Auto-manual-semi auto & test switches

1 No. status indicator

UPS for required operation

1 No. Auxiliary transformer (star/star)

1 No. printer A3 size

PC as per specifications ( Refer list of makes of materials)

Metering

Power & Energy monitor model (EM 6400 with RS- 238/485 port accuracy class 0.5)

Visual Indications & Control

1 set running

1 No. Emergency stop push button

1 No. Breaker close push button

1 No. Breaker trip push button

Annunciation

Annunciator with hooter, test, accept and reset Push button & Annunciate

Annunciator Inscriptions:

Solid state Annunciator ( 2 Nos. DG sets) for DG-1/ DG-2

Inscription:

Electrical Fault

Excitation Failure

Reverse Power

Emergency Shutdown

Over speed

Low Lube oil pressure

High water temperature

Engine overheating

Bearing temperature high

Winding temperature high

Low fuel level

Exhaust quality

Spare

Spare

Spare

Spare

Solid state Annunciator (1 No.) for ASP

Inscription

DG-1 Fails to Start

DG-1 Neutral Discrepancy

DG-1 ACB Fails to Close

DG-2 Fails to Start

DG-2 Neutral Discrepancy

DG-2 ACB Fails to Close

Annunciator shall have facility for PC interface

Status indicator Annunciator ( 1No.) for ASP

DG-1 Supply Available

DG-1 ACB connected to Bus

DG-1 Neutral ON

DG-2 Supply Available

DG-2 Supply Available

DG-2 ACB connected to Bus

DG-2 Neutral ON

BC - ACB ON

System operation:

The emergency Diesel -Alternator sets will function as follows:

DG SUPPLY : 2 NOS

MAINS SUPPLY : 2 NOS.

BUS COUPLER : 1 NOS

Manual Mode:

Two different source / supply can’t be paralleled as interlocking is Provided between all the incomers and Bus Couplers in both Auto/Manual mode.

PLC on manual mode:

When all Grid supply available, breaker of all mains shall be switched ON with B/C in off position, all sections of bus bar will be fed through Grid supply.

On Grid failure all mains breaker will get tripped and depending on the load demand any one of the DG can be started and respective DG Breaker along with bus-coupler can be switched ‘ON’ to charge the complete Bus manually. However D.G. can be started automatically if it is in Auto Mode.

We can run one D.G. and one mains supply (but not on the same bus) with bus coupler in off position or Vice-Versa.

No time delay shall be applicable in Manual Mode for closing and tripping of air ckt. Breaker.

Auto Mode:

Grid Supply Healthy:

When all mains supply available, breaker of all mains shall be switched ON with B/C in off position, all sections of bus bar will be fed through Grid supply.

On Grid Failure:

Option – 1

DG 1 in auto mode, rest of D.G.s in manual or in off mode. As Soon as Grid fails DG1 will be started automatically. Healthiness of the DG1 voltage will be sensed by PLC through Under Voltage Relay provided in DG incomer and closing command will be given by PLC to DG1 incomer Breaker and B/C will have time delay of 10 seconds, will be closed so that complete load will be feed through DG1 and similarly in case with DG2

Option – 2

DG1 & DG2 in Auto mode and other DG sets are Manual or in off Mode In this case both the DG sets will start as soon as grid fails. After attaining proper Voltage PLC will give closing command to DG1, DG2 and bus coupler will get tripped. If either of DG fails to start than in-between bus coupler will get closed to charge the complete bus through single DG set. Further if faulty DG becomes healthy and comes in line than in-between bus coupler will get tripped and DG breaker will get closed.

Option – 3

If all D.G.s are in Auto mode then the bus coupler will be in ON position and the DG will get Start one by one as per the priority set as per the load conditions.

If load on DG exceeds 80% of its full load after 10 sec. of time delay in order to check load consistency, the next DG which is in auto mode and healthy condition will start automatically bus coupler will get tripped through PLC and DG breaker of new DG will get closed.

On mains restoration of (45 seconds stabilized) supply all DG Breaker will gets tripped and Mains breaker will get closed. B/C will get closed with time delay say of 10 seconds. On further failure of Grid supply same sequence of operation will be followed as above.

NS 86 - Supplying, installation, testing and commissioning of free standing, front operated cubical type capacitor control panel with aluminium bus bars of current density 0.8Amps/sq.mm.& rupturing capacity(50KA), LED indicating lamps interconnections with under noted switch gears as per technical specifications and drawings complete as required. All MCCB shall have rotary operating handles. (capacitor control panel)

Note-1) DESIGN, TESTING & CERTIFICATION OF PCC PANEL's MUST COMPLY IEC-61439, ALONG WITH IEC-61641 FOR INTERNAL ARC FLASH

420 kvar capacitor control panel

1 No.800A ,TPN ,50KA,MDO ACB with releases for O/C,S/C&E/F.protection..

1 No. Ammeter (digital type) with inbuilt ASS

1 No.Volt Meter (digital type) with inbuilt VSS & control fuses.

1 No.12 step A.P.F.C.Relay (intelligent micro-processor based with current sensitivity less than 1%)

3 Nos. CTs-800/5 Amps. Cl-1

1 Set phase indication lights (R, Y, B)

800 Amps. TP&N aluminium bus bars (50 KA)

8 No.100 Amps. TPN MCCB(50 KA) with electronic releases.

7 No. 60 KVAR TP Shunt capacitor Heavy duty MPP type with discharge resistor and 7% D-tuned Harmonic reactor filter

7 No. 120 Amps. TP capacitor duty contactors.

12 Sets self illuminated Red-Green ON-OFF push buttons. 2 Sets of Axial flow fans with thermostate.

NS 87 - Supplying, installation, testing and commissioning of cubical type MV Panel made out of 14 SWG CRCA sheet steel, totally enclosed IP-54 protection, free standing, floor mounted dust and vermin proof, indoor type compartmentalized powder coated of approved shade after antirust treatment (with min seven tanks ) suitable with busbar interconnection with suitable size of copper lead/solid Aluminium strips, control circuits & bottom base channel of MS section not less than 100mmx50mmx5mm (thick), Fabrication shall be done in transportable section ,entire panel shall have a common earth busbar at rear with 2 nos earth stud cable alleys, cable gland plates in two half as required as per single line diagram & specification enclosed with the following switch gears

All MCCBs shall have Ics=Icu=100%

MCB Should be connected throught terminal Strip of suitable rating

All outgoing MCCB feeders shall have ON/OFF Trip indication lights (LED Type)

NS 87.1 - Panel Specification as stated above (Floor Panel)

Incomer

1 No. 315 A FP MCCB (36 KA)

1 Set phase indication lights (R, Y, B)

1 No. Volt Meter (digital type) with inbuilt VSS & control fuses.

1 No. 0-315 Amp. Ammeter (digital type) with inbuilt ASS

Provision of Space for dual source energy meter with CT

BUS BARS:-

315 Amps. TP&N aluminium bus bars (36 KA)

OUT GOINGS:-

6 Nos 40 Amp. FP MCB (25 KA)

4 Nos 63 Amp. FP MCB (25 KA)

4 Nos. 100 Amps. FP MCCB (25KA)

NS 87.2 - Panel Specification as stated above (Main UPS Panel)

Incomer

2 No. 200 A FP MCCB (36 KA)

2 Set phase indication lights (R, Y, B)

2 No. Volt Meter (digital type) with inbuilt VSS & control fuses.

2 No. 0-200 Amp. Ammeter (digital type) with inbuilt ASS

BUS BARS:-

400 Amps. TP&N aluminium bus bars (36 KA)

OUT GOINGS:-

6 Nos. 100 Amps. FP MCCB (25KA)

NS 87.3 - Panel Specification as stated above (Lift Panel)

Incomer

1 Nos 250 Amps Automatic Change Over Switch

1 No. 250 A FP MCCB (36 KA)

1 Set phase indication lights (R, Y, B)

1 No. Volt Meter (digital type) with inbuilt VSS & control fuses.

1 No. 0-250 Amp. Ammeter (digital type) with inbuilt ASS

BUS BARS:-

400 Amps. TP&N aluminium bus bars (36 KA)

OUT GOINGS:-

6 Nos. 125 Amps. FP MCCB (25KA)

Sub Outgoing

6 Nos. 40 Amps. DP MCB (25KA)

EXTERNAL LIGHTING

NS 88 - Supplying, installation, testing and commissioning of L.T. panel fully compartmentalized cubical type sheet clad floor mounted totally enclosed , extensible on both sides, switch board suitable for use on 415 Volts 3-phase, 4 wire, 50 Hz system having required fault capacity, housed with incoming and outgoing, Aluminium bus bars with current rating of 0.8 Amp/sq.mm, interconnection etc. with indication lamps, accessories etc, as required as per specification and schematic diagram as required. (Street lighting Panel)

INCOMER:-

1 Nos.160 Amps. TPN MCCB(25 KA) with electronic releases.

1 Set phase indication lights (R, Y, B)

1 No. Volt Meter (digital type) with inbuilt VSS & control fuses.

1 No. 0-200 Amp. Ammeter (digital type) with inbuilt ASS

BUS BARS:-

200 Amps. TP&N Aluminium bus bars (25 KA)

OUT GOINGS:-

8 Nos. 40A TPN, MCB (10KA).

6 Nos. 24 Hr Timer Switch

6 Nos. 63A TPN contactor

NS 89 - Supplying, installation, testing and commissioning of following ratings of MCCBs/ACB installed in sheet steel enclosure with indicating lamps etc., earthing, connections, as per specifications complete as required.

NS 89.1 - 1000 Amps FP ACB

NS 90 - Supply and burring of Safe Earthing Electrode T-19 (Hot Dip Galvanized), Length up to 2000mm, outer pipe 50mm, inner pipe 25, terminal Dia 12 mm, outer GI pipe of 16 swg and inner GI pipe of 12 swg with Hot Dip Galvanization up to 100 micron filled with crystalline conductive mixture (CCM) having anti corrosive & conductive property with 50 kgs activated soil (BFC) capable of reducing the soil resistivity with good mixture of retaining capacity along with 30cm square C.I. frame with hinged cover & masonry husing (from electrode terminal to switch board, cost of 25 x 3 G.I . strip will be extra) Make: As approved in U.P. P.W.D., & C.P.R.I. Certified

NS 91 - Supplying, installation, testing and commissioning of following ratings of MCCBs/ACB installed in sheet steel enclosure with indicating lamps etc., earthing, connections, as per specifications complete as required.

NS 91.1 - 3.5 x 400 sq.mm

NS 91.2 - 3.5 x 300 sq.mm

NS 91.3 - 3.5 x 240 sq.mm

NS 91.4 - 3.5 x 185 sq.mm

NS 91.5 - 3.5 x 150 sq.mm

NS 91.6 - 3.5 x 120 sq.mm

NS 91.7 - 3.5 x 95 sq.mm

NS 91.8 - 3.5 x 70 sq.mm

NS 91.9 - 3.5 x 50 sq.mm

NS 91.10 - 3.5 x 35 sq.mm

NS 91.11 - 3.5 x 25 sq.mm

NS 91.12 - 4 x 16 sq.mm

NS 91.13 - 4 x 10 sq.mm

NS 91.14 - 4 x 6 sq.mm

NS 91.15 - 3 x 10 sq.mm

NS 91.16 - 3 x 6 sq.mm

NS 91.17 - 2 x 16 sq.mm

NS 91.18 - 2 x 10 sq.mm

NS 91.19 - 2 x 6 sq.mm

NS 92 - Supply, laying, connecting, termination and testing of under noted sizes of flexible copper conductor flexible PVC sheathed & sleeved and overall PVC sleeved 1.1 KV grade power distribution cables conforming to relevant IS code and as per specification in ground (in existing trenches) through pipe or on wall / racks cable trays including dressing and clamping the cable with MS zinc passivated clamps etc. as required.

NS 92.1 - 1 C x 70 sq.mm

NS 92.2 - 1 C x 35 sq.mm

NS 93 - Supply, laying and testing of under noted sizes of copper conductor XLPE insulated PVC sheathed & sleeved armoured and overall PVC sleeved 1.1 KV grade power distribution cables conforming to relevant IS code and as per specification in ground (in existing trenches) through pipe or on wall / racks cable trays including dressing and clamping the cable with MS zinc passivated clamps etc. as required.

NS 93.1 - 4 x 6 sq.mm

NS 93.2 - 4 x 4 sq.mm

NS 93.3 - 2x 2.5 sq.mm

NS 94 - Supply and making end termination with brass double compression gland including providing and crimping of copper heavy duty solderless lugs / ferrules for XLPE armoured power copper conductor cable 1.1 KV grade of following sizes:-

NS 94.1 - 4 x 6 sq.mm

NS 94.2 - 4 x 4 sq.mm

NS 94.3 - 2x 2.5 sq.mm

NS 95 - Supply, installation, testing & commissioning of the following: IGBT based 60 KVA parallel True Online Double Conversion UPS suitable for unbalanced, 3 Phase input and 3 phase 415 V output, power Fcator 0.9 or more. UPS system with isolation transformer (i.e., K-13 type), suitable for operating in parallel and each comprising as per technical specification complete as required with VRLA sealed maintenance free batteries for 60 KVA UPS system, for providing 30 minutes back up to each 60 KVA UPS. Each bank of batteries shall comprise required Nos. of SMF batteries etc as per specifications as required. Matching cabinet to house SMF batteries for 60 KVA UPS system along with interconnecting links and I/c S/F MCCB as required.

NS 96 - Supply, laying and testing of under noted sizes of copper conductor XLPE insulated PVC sheathed & sleeved armoured and overall PVC sleeved 1.1 KV grade power distribution cables conforming to relevant IS code and as per specification in ground (in existing trenches) through pipe or on wall / racks cable trays including dressing and clamping the cable with MS zinc passivated clamps etc. as required.

NS 96.1 - 4 x 2.5 sq.mm

NS 97 - Supply and making end termination with brass double compression gland including providing and crimping of copper solderless lugs / ferrules for XLPE armoured power copper conductor cable 1.1 KV grade of following sizes:-

NS 97.1 - 4 x 2.5 sq.mm

NS 98 - Supplying, laying, connecting,terminating, testing & commissioning of under noted sizes of PVC insulated, PVC sheathed unarmoured and overall PVC sleeved 1.1 KV grade control cables in pipe, wall, racks, cable trays, including, dressing, clamping with M.S Zinc passivated clamps etc as required conforming to relevant IS code and technical specifications.

NS 98.1 - 8C x 1.5 sq.mm

NS 98.2 - 10C x 1.5 sq.mm

NS 98.3 - 14C x 1.5 sq.mm

NS 99 - Supplying and fixing ladder type prefabricated CRCA sheet steel Stove enameled cable tray complete with bend/tee joints, coupling plate and nut bolts washers etc. including providing and fixing of hangers etc. as required.

NS 100 - Supplying, Laying, terminating, testing, commissioning of following sizes of Copper Conductor PVC insulated, PVC sheathed armoured cable 1100 V grade. On surface the cable run shall be fixed on G.I. clamps etc of suitable size or as directed by the E-I-C complete in all respects. Supply and providing cable identification markers. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. as per specifications complete with end termination as required.

NS 100.1 - 24 C x 2.5 Sqmm

NS 100.2 - 2 C X 4.0 Sqmm

NS 100.3 - 3 C X 6 Sqmm

NS 101 - Supplying, installation testing and commissioning of 1000 kVA, outdoor type, oil cooled, distribution transformer, suitable for 3 phase, 50HZ, AC supply, rated turn/voltage ratio of 11kV/0.433kV,Dyn 11 vector group, percentage impedence of 5%, oil immersed naturally cooled (ONAN) mechanism,core made of good quality CRGO, windings made of double wound copper, insulation class A,approved danger and arc flash signages and with all components as mentioned in BOQ, specifications and SLD & confirming IS 1180 Level-II losses, complete as required.

Cable termination box with disconnecting facility for 11 KV XLPE cable at 11 KV side suitable for 11kV(E) 3C x 300 sqmm XLPE Cable

Bus Trunking Provision LV Side of Transformer as per SLD

On load tap changer +5 to - 15 % in the steps of 1.25 with RTCC and AVR

Bi directional rollers

Conservator with drain valve

Earthing terminals.

Explosion vent with double diaphragm and sight glass.

Radiator with top & bottom shut off valve.

First filling of oil including make up fill.

Silica gel breather with oil seal.

Rating and diagram plate.

Air release plug.

Buchholz relay with shut off valve.

Winding temperature indicator. (WTI)

Oil temperature indicator. (OTI)

Magenatic oil level gauge.

Pressure relief device.

Marshalling box with watertight lockable cover lid and all associated accessories as per schedules and specifications.

Drain cum bottom filter valve

Oil surge relay.

NS 102 - Supplying, installation, testing and commissioning of of HT PANEL BOARD

A. Incomming Panel 1 Nos. each shall be comprising of:

1- Metal Clad housing with track having 1250A TP integral VCB with Electric operated draw out type mechanism (spring charged motor - 230 VAC).

1- Set of air insulated copper bus bar & chamber.

1- Set of isolating plug and receptacle.

1- Set of Automatic safety shutter.

1- Set of breaker control switch (TNC)

2- Sets of CT's

CT- I -800/400/5A class 5P-10(15 VA)

CT- II –800/400//5A class -1(15 VA)

3 - Nos. PT's 11KV /Rt.3 /110V/Rt 3 of (100 VA) cast resin type.

1 - H.T. Cable box for 3C x 300 sq.mm aluminium conductor XLPE cable (11 KV earthed system).

1 - No. Tripping coil & closing Coil 24V DC/110V A.C.

1 - Set of ON/OFF/Trip & circuit healthy and phase indicating lights.

1- 3 element O/C, EF & SC relay (IDMTL & Hi - set) with required setting.

1- set Auxiliary relay.

1- Master trip relay

1-set Trip circuit supervision

1-Restricted Earth fault relay

B. Outgoing Panel 2 Nos. each shall be comprising of:

1- Metal Clad housing with track having 630A TP integral VCB with Electric operated draw out type mechanism (spring charged motor - 230 VAC).

1- Set of air insulated copper bus bar & chamber.

1- Set of isolating plug and receptacle.

1- Set of Automatic safety shutter.

1- Set of breaker control switch (TNC)

2- Sets of CT's

CT- I -200/100/5A class 5P-10(15 VA)

CT- II - 200/100/5A class -1(15 VA)

1 - H.T. Cable box for 3C x 300 sq.mm aluminium conductor XLPE cable (11 KV earthed system).

1 - No. Tripping coil & closing Coil 24V DC/110V A.C.

1 - Set of ON/OFF/Trip & circuit healthy and phase indicating lights.

1- 3 element O/C, EF & SC relay (IDMTL & Hi - set) with required setting.

1- set Auxiliary relay.

1- Master trip relay

1-set Trip circuit supervision

1-Restricted Earth fault relay

NS 103 - Supply, erection, testing & commissioning of 230 V, single phase, 2 wire, A.C. to 24V D.C. 180 AH sealed maintenance free batteries with semiconductor/ IGBT (half wave rectifier) with auto-manual trickle boost facility battery charging units complete including 1 No. Distribution board having 63 Amps DP MCB incomer and 12 No. 16/ 20 Amps DP MCBs (D.C. duty) as outgoing complete as required as per technical specifications.

NS 104 - Supplying and fixing of non-skid rubber mat 25mm thick and 900mm width as required including cutting to required lengths of approved make with Test Certificates for H.T. 11 KV panels.

NS 105 - Supplying and fixing of non-skid rubber mat 16mm thick and 900mm width as required including cutting to required lengths of approved make with Test Certificates for L.T. panels.

NS 106 - Supplying and fixing of fire bucket painted red and duly filled with sand conforming to IS: 2546-1974.

NS 107 - Supplying and fixing of MS stand suitable for supporting two buckets (Pedestal type)

NS 108 - Supplying and fixing of MS stand suitable for supporting four buckets (Pedestal type)

NS 109 - Supplying and fixing of shock restoration chart written in English and Hindi duly framed in as required.

NS 110 - Supplying and fixing of carbon dioxide fire extinguisher type 4 kgs. Capacity of approved make with wall mounting bracket as required conforming to IS: 2878/1976 (Push type).

NS 111 - Supplying and fixing of first aid box as approved complete with standard kit as prescribed by Indian Red Cross.

NS 112 - Supply of 13M long MS pole (Swaged type) as per IS-410 SP-70 with acessories as required.

NS 113 - Supply of 11 KV, 3 phase, 630 Amps central post racking type gang operated switch with earth switch complete with hardware, arcing horns, arcing contacts, vertical drop out fuses, down rod operating with locking devices, necessary MS channel/angle iron brackets, clamps insulators & connections etc. as required for earthed system and conforming to IS: 19813.

NS 114 - Supplying and laying of the 250mm dia 'B' class GI pipe complete with all accessories as required as per specifications.

NS 115 - Supply of one number PVC insulated and PVC sheathed/XLPE Power cable of 11 kV Grade of following size 3Cx300 sq. mm

NS 116 - Supply and fixing of decorative 45 Watt LED Post top indirect light luminaire having Pressure die cast aluminium body and Clear glass with driver set confirming to IP 65 and above protection complete in all respect including connecting copper wiring.

NS 117 - Supply & Erection of 3 meter long GI Decorative pole for above post top fitting with inbuilt junction box,MCB,sleeve in foundation and required wiring till fixture in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) foundation including excavation and refilling etc. as required.

NS 118 - Supply and fixing of decorative 9/10 Watt LED bollard luminaire with driver set confirming to IP 65 protection complete in all respect including foundation and connecting copper wiring.

NS 119 - Supply and fixing of LED Street light Fitting having die cast aluminium body and diffuser with driver set suitable for 140 to 150 Watt. Confirming to IP 66 Protection complete in all respects including connecting copper wiring

NS 120 - Supply & fixing of 9mtr GI Octagonal Pole of approved make (top dia 70mm, Bottom dia 155 mm and base plate 12mm thik) having 3mm thikness with single arm bracket (1 Mtr length) on RCC foundation including the cost of foundation, foundation bolts, excavation & back filling and with inbuilt junction box with MCB,and wiring till fixture, sleeve in foundation,Required T&P completee in all respect.

NS 121 - Supply & fixing of 9 mtr GI Octagonal Pole of approved make (top dia 70mm, Bottom dia 155 mm and base plate 12mm thik) having 3mm thikness with Double arm bracket (1 Mtr length) on RCC foundation including the cost of foundation, foundation bolts, excavation & back filling and with inbuilt junction box with MCB,and wiring till fixture,sleeve in foundation, Required T&P completee in all respect.

NS 122 - Supply and fixing of factory wired integral LED flood light luminaires with die cast aluminium housing built with dirver set suitable for 80 Watt. Confirming to IP 65 protection complete in all respect including connecting copper wiring.

NS 123 - Providing, Installing, Testing and Commissioning of ‘Silent Type’ Diesel Generating set alongwith having Prime Power Rating of 625 KVA, 415 volts at 1500 RPM, 0.8 lagging power factor at 415 V suitable for 50 Hz, 3 phase system & for 0.85 Load Factor and consisting of the followings:

(a) Diesel Engine:

Diesel engine 4 stroke water cooled, electric start, of suitable BHP at 1500 RPM suitable for above output of alternator at 40 Degree C, 50% RH & at 1000 Meter MSL and conforming to BS 5514, BS 649, IS 10000, capable of taking 10% over loading for one hour after 12 hours of continuous operation. The engine will be fitted complete with all the required accessories.

(b) Engine mounted Instrument Panel fitted with and having digital display for following:

(i) Start-stop switch with key

(ii) Water temperature indication

(iii) Lubrication oil pressure indication

(iv) Lubrication oil temperature indication

(v) Battery charging indication

(vi) RPM indication

(vii) Over speed indication

(viii) Low lub. Oil trip indication

(ix) Engine Hours indication

(c ) Alternator :

Synchronous alternator rated at 625 KVA, 415 volts at 1500 RPM, 3 phase 50 Hz, AC supply with 0.8 lagging power factor at 40 Degree C, 50% RH & at 1000 Meter MSL. The alternator shall be having SPDP enclosure, brushless, continuous duty, self-excited and self-regulated through AVR conforming to IS: 4722/BS 2613 suitable for tropical conditions and with class- F/H insulation.

(d) Base Frame & Foundation:

Both the engine and alternator shall be mounted on suitable base frame made of MS channel with necessary reinforcement which shall be installed on suitable cement concrete foundation and vibration isolation arrangement as per recommendations of manufacturer.

(e) Fuel Tank:

Daily service fuel tank of 990 liters capacity fabricated out of 3 mm thick M.S. sheet complete with all standard accessories and fuel piping between fuel tank and diesel engine with MS class ‘C’ pipes of suitable dia. Complete with valves, level indications & accessories as required as per specifications.

(f) Exhaust System:

Dry exhaust mainfold with hospital exhaust silencer and catalytic convertor.

(g) Starting System:

12V/24V DC starting system comprising of starter motors: voltage regulator and arrangement for initial excitation complete with suitable nos. of batteries (25 plates, 180 Amp. Hour capacity lead acid type) as required as per specifications.

(h) Accoustic and weather proof enclosure with arrangement for fresh air intake for cooling of the engine & alternator, extraction, discharging hot air in to the atmosphere as per specifications.

LIFTS

Supply,Installation,testing Commissioning of Below described lifts complete as per specification and as per direction of Engg-In Charge

NS 124 - Supply, installation testing and commissioning of lifts(with Machine Room) of maximum rated load 16 passenger, speed 1.5 mps of simplex system travelleing for B1 +B2 +G +6 floors of travel height ( 32 mts approx.). Hair line stainless steel SS304 , centre opening automatic door of fire retardent capacity not less than 2hours inclusive of all accessories, gadgets, car operating panel indicator, door close and open button alarms, colour LCD display, emergency phone, handicapped COP, braille push buttons, star light ceiling finish inside the car, tiles finish, and all other devices complying to fire escape, emergency evacuation control, NBC etc. complete in all respect etc. (As per Data Sheet in Technical Specification)( Passenger Lift) Note- Opertation of lift is covered under scope of work till the handing over of lifts to client.

NS 125 - Addition and deletion of cost per floor on below stated size of lift as per requirement of site. 16 Persons (1088 KG) (With m/c Room) Lift with speed of 1.5 M/Sec. (dimensions and travelling as per drawing)

IP CCTV System

NS 126 - SITC of IP Dome Camera 4MP IR Dome Camera, Metal Housing, H.265+/H.265/H.264, Up to 2592x1520@25fps, Min. illumination Color: [email protected], Smart IR, IR Range: 30m, Built-in Mic, SD Card Slot, Reset Button, POE, IP67, IK10, 120dB WDR, Support tripwire and perimeter, ANR. BIS,CE,FCC,ROHS,UL/EN. etc all complete.

NS 127 - SITC of IP Bullet Camera 4MP IR Bullet Camera, Metal Housing, H.265+/H.265/H.264, Up to 2592x1520@25fps, Smart IR, IR Range: 50m, Built-in Mic, SD Card Slot, Reset Button, 120dB WDR, POE, IP67, 120dB WDR, Support tripwire and perimeter, ANR. BIS,CE,FCC,ROHS,UL/ENetc all complete.

NS 128 - SITC of IP PTZ Camera 2 MP -IP PTZ Camera 2 MP - IP Network 1/2.8" CMOS, Dual IR Cut Filter , 1920x1080:30fps, H.264/MJPEG Or better, Triple streams, AC24V/POE+, IP66, Micro SD card slot support up to 128GB, Alarm in/out 1/1, Audio in/out 1/1, -30-65℃, IP66, 33x optical zoom(4.6 ~ 152mm), IR range: up to 150m, 120dB WDR, IP66, 33X optical zoom, HLC,BLC,3D DNR, Smart functions-Auto Tracking, CE, FCC, Defog, Privacy mask, Up to 8 Pattern, Presets – 300 , PAN Range - 360° , 0.1°/s ~ 180°/s ,Tilt Range -–16° ~ 90° (auto flip) , 0.1° ~ 120°/s etc all complete. Certificate – BIS, CE, FCC, ROHS, UL/EN etc all complete.

NS 129 - SITC of NVR - H.265 8SATA 64ch NVR, H.265+ Compression, Support 64-ch input, Up to 12MP Resolution Recording, Incoming Bandwidth 320Mbps, Outgoing Bandwidth 320Mbps, HDMI and VGA independent outputs, HDMI Video output at up to 4K (3840 × 2160) resolution, 8 SATA interfaces for 8 HDDs, up to 10TB for each HDD, eSATA interface:- 1 SATA interface, 2xRJ45 self-adaptive 10/100/1000 Mbps network interfaces, VCA detection alarm is supported, Array Type:- JBOD, RAID0/1/5/6/10, 2xUSB 2.0, 1xUSB 3.0, serial Interface:- 2xRS-485, 1xRS-232, No.of Hard Disks 4TB for the calaculation of 1 month recording 2MP@25FPS as per all camera count, VMS should also be included if required etc. all complete.

NS 130 - SITC of 10 TB Survillance Sata Type HDD for Network video Recorder etc all complete

NS 131 - SITC of MS Windows 2008 Server R2 x64, Intel i5 Xeon Quad Core processor, 8 GB RAM, 1TB HDD, 2GB Graphics Card. With CD/DVD player, Mouse and Keyboard etc all complete.

NS 132 - SITC of 55" Professional Display Panel, 4K/UHD Resolution, Direct-lit LED, Brightness 400 nits, Contrast ratio 1200:1, inputs: 2 HDMI, DVI, DisplayPort, Audio inputs with mounting arrangements etc all complete

Access Control System

NS 133 - SITC of IP Based Master controller with 2,40,000 Card holder capacity, 50,000 event buffer. Natively supports 4 readers and 2 openings over OSDP and expandable upto 64 readers with IP Based interface module. UL294 Listed,FCC, CE, RoHS, NIST Certified Encryption etc all complete

NS 134 - SITC of IP based Reader Interface module. Supports 2 Door- 2 reader over weigend and 2 Door- 4 Reader over OSDP. Also works with PoE & PoE+ . UL294 Listed, FCC, CE, RoHS, NIST Certified Encryption etc all complete

NS 135 - SITC of Iclass Smart card reader1. Operating Frequency: 13.56 MHz Contactless Smart Card Reader Data Formats: Wigand, OSDP, Keypad Data Formats : Field configurable, 8-Bit Burst (default) and 26-Bit Wiegand, Certifications and Compliance: UL294/cUL (US), FCC, IC, CE,C-Tick, MIC, NCC Housing Material UL94 Polycarbonate etc all complete

NS 136 - SITC of Enclosure with UL Listed Power Supply for Controllers etc all complete

NS 137 - SITC of UL294 Listed Biometric device with inbuilt smart card reader CPU: ARM Cortex-A9 core 1GHz, Linux Operating System, Fake finger detection, Duress finger, FBI PIV IQS certified optical fingerprint senso, Network/Communication, Ethernet, RS485, USB,Integrated Smart Card Reader, Internal storage capacity: 512MB Flash, 512MB RAM, Operating conditions: - Temperature: -20°C to 55°C (-4°F to 131°F), Humidity: 10% to 80% (non condensing), Ingress protection: IP65 and EMC/Safety standards: - CE, CB, FCC, BIS, UL294 , RoHS, REACh and WEEE compliant etc all complete

NS 138 - SITC Smart card Frequency Excitation (13.56 MHz) Mifare/I-class technology smart Card. Memory Type EEPROM,Complies with ISO/IEC standards for thickness. Lifetime Warranty etc all complete

NS 139 - SITC of Single Door Electro Magnetic Lock Approved,Monitored Single Leaf/Double Leaf Electromagnetic Lock with 600/1200 lbs holding force with dual Monitoring and tested for 45 min on fire door assemblies fire rating including necessary mounting brackets Standards: UL Listed or CE Certified etc all complete

NS 140 - SITC of Double Door Electro Magnetic Lock Approved,Monitored Single Leaf/Double Leaf Electromagnetic Lock with 600/1200 lbs holding force with dual Monitoring and tested for 45 min on fire door assemblies fire rating including necessary mounting brackets Standards: UL Listed or CE Certified etc all complete

NS 141 -Supply Installation Testing and Commissioning Touchless Request to Exit button with detection range from 4 to 12 cm , 0.1 million cycle tested .

NS 142 - Supply Installation Testing and Commissioning Emergency Door Release Button, Gree, Key Resettable, Double Pole Double Throw (DPDT) etc all complete

NS 143 - Supply Installation Testing and Commissioning of Network Cat6A cable ( Complete Roll 305 Mtr aoorox)

NS 144 - Supply Installation Testing and Commissioning of 2-conductor 4 core 20 to 22 AWG

NS 145 - Supply Installation Testing and Commissioning of RS485 2 twisted pair, individually shielded, 18 to 22 AWG

NS 146 - Supply Installation Testing and Commissioning of Power Cable 3*1.5 sqmm PVC insulated flexible FRLS copper

NS 147 - SITC of Web Based Standard Application for Time Attendance-Access Control, GUI, Antipass back, Reports in Inbox, with Unlimited Users, Door Scheduling, Unlimited Client logins, Event Notification, POP ups, Mustur Points, Area Control, Time base access and alerts. Software should be VAPT approved and should provide Per reader license, Should have integrated modules of Elevator management, Visitor Management, Template management and card priting module , Integrated credential issuance application inclusive of card template designing, card printing, finger print enrollment, key management, contactless card reader/writer & contact card reader/writer etc all complete

NS 148 - SITC of Visitor Managment Software Application to allow employees to pre- register visitors & visitor request approval management etc all complete

NS 149 - SITC of MS Windows 2008 Server R2 x64, Intel i5 Xeon Quad Core processor, 8 GB RAM, 1TB HDD, 2GB Graphics Card. With CD/DVD player, Mouse and Keyboard etc all complete.

NS 150 - SITC of motorized Boom barrier,6 Mtr Boom Length open closing time 2 Sec(Adjustable),IP 54,MTBF 2 Million etc all complete,CE certified etc all complete.

IT Data Networking and Voice System (Passive Component)

NS 151 - SITC of LSZH Cat 6A-10G speed unshielded twisted pair computer cable with 23 AWG solid copper conductors in existing concealed/surface conduits/Raceways complete 305 Mtr. Roll as per specification etc. all complete.

NS 152 - SITC of Single port faceplate with Gang Box etc. all complete.

NS 153 - SITC of Dual port faceplate with Gang Box etc. all complete.

NS 154 - SITC of UTP Cat-6A Information Outlet Red for Data, Voice and IP CCTV as per specification etc. all complete

NS 155 - Supply of CAT6A Ceiling Connector with CAT 6A Copper pigtail with moudled RJ45 Plug (for Wireless AP's)

NS 156 - SITC of Cat-6A Mounting Cords 7 Feet for Data and Voice as per given Specification etc. all complete.

NS 157 - SITC of Cat-6A Mounting Cords 4 Feet for Data and Voice Jack Panel end as per given Specification etc. all complete.

NS 158 - SITC of Cat-6A, 24 Port Jack Panel for data as per given Specification etc. all complete.

NS 159 - SITC of Cat-6A, 24 Port Jack Panel for Voice as per given Specification etc. all complete.

NS 160 - SITC of Cat-6A, 24 Port Jack Panel for CCTV and ACS as per given Specification etc. all complete.

NS 161 - SITC of Cable Manager for above jack panels as per given Specification etc. all complete.

NS 162 - SITC of 12 Core Single Mode Fiber (Armored) Cable as per given Specification etc. all complete.

NS 163 - SITC of 12 Port Fiber LIU Loaded with SC SM Coupler, as per given Specification etc. all complete.

NS 164 - SITC of 24 Port Fiber LIU Loaded with SC SM Coupler, as per given Specification etc. all complete.

NS 165 - SITC of SC SM Pigtail (1.0 Mtr) as per given Specification etc. all complete.

NS 166 - SITC of SC-LC SM Fiber Patch Cords ( 3 Mtr) as per given Specification etc. all complete.

NS 167 - SITC of 9U (W 600mm/ D 600mm) wall mount with front glass door and side panels with lock & key (load bearing capacity of 40Kgs), AC main Channel 06 points 5 Amp (PDU) with Mounting Hardware (Pack of 10) ect all complete

NS 168 - SITC of 15U (W 600mm/ D 600mm) wall mount with front glass door and side panels with lock & key (load bearing capacity of 40Kgs), AC main Channel 06 points 5 Amp (PDU) with Mounting Hardware (Pack of 10) ect all complete

NS 169 - SITC of 42U Close Floor Mounted Rack - (800 mm x 1000 mm - W X D), with Perforated doors (Front & rear), 2 Nos. of 1U power distribution box, with 10 x IEC - C13 sockets & with 32Amp MCB- terminating on a IP56 power sockets - VERTICAL - in each rack, 2 No. Horizontal PDU with 5/15Amp Universal Sockets with 32Amp MCB - in each rack, Front mounting PVC Cable managers/ guide x 10 in each rack (1U Horizontal), Integral Cable management ducts/ arms (on either side) with covers, Fan housing unit 4 Fan POSN - 90 CFM 230VAC, Bar, Earthing 42U with Mounting Hardware (Pack of 10) ect all complete

NS 170 - SITC of 1000 Pair MDF Box with Mounting Frame etc all complete

NS 171 - SITC of 50 Pair Riser cable etc all comlete

NS 172 - SITC of Huck up wire of 305 meter role etc all complete

IT Data Networking and Voice System (Active Component)

NS 173 - SITC of 24 Port Edge/Accsess Switch (Data & WiFi), 24 x 10/ 10 0/ 10 0 0BASE-T (RJ-45) PoE-Plus Half, Full, Auto Duplex | 2 x 10 GBASE-X SFP+, Serial (console port RJ-45), USB, RPS port, fully loaded with SFP/SFP+ Module etc all complete

NS 174 - SITC of 24 Port Edge/Accsess Switch (CCTV and ACS), 24 x 10/ 10 0/ 10 0 0BASE-T (RJ-45) PoE-Plus Half, Full, Auto Duplex | 2 x 10 GBASE-X SFP+, Serial (console port RJ-45), USB, RPS port, fully loaded with SFP/SFP+ Module etc all complete

NS 175 - SITC of 48 Port Edge/Accsess Switch ((Data & WiFi)), 48 x 10/ 10 0/ 10 0 0BASE-T (RJ-45) PoE-Plus Half, Full, Auto Duplex | 4 x 10 GBASE-X SFP+, Serial (console port RJ-45), USB, RPS port, fully loaded with SFP/SFP+ Module etc all complete

NS 176 - SITC of L3 Distribution Switch, 24 x 10GBase-X (SFP+) ports, 2 x Stacking/QSFP28 ports, Serial console port, 10/100/1000BASE-T out-of-band management port, VIM slot, fully loaded with fibre module and all required accessories etc all complete

NS 177 - SITC of Router with 4 X 10G SFP+ Ports and 16X10/100/1000 Base-T ports. The device should have 4 Gbps of IMIX/Real World throughput. 6 Gbps of Application Visibility and Control, 1 Gbps of IPSec VPN with 2000 VPN tunnels support. Should support min 4GB internal DRAM, 16GB internal Flash memory. Should have redundant power supply. Should be SD-WAN ready for any future requirement etc all complete

NS 178 - SITC of Firewall solution with minimum of 500 users from day one with 1 years of subscription / support and flexibility to scale up to 2000 users. This solution should have Firewall performance (Real World/IMIX) of 20 Gbps, IPS performance of 15Gbps, NGFW throughput of 9 Gbps, Connections per second 250K, Maximum sessions of 5 Million and includes following features as per detailed specification: Web Security, Next Generation Firewall, IPS, Applications Visibility/AVC, Routing capabilities enabled as BGP, RIP v1/v2, OSPF, IS-IS, IPv4, IPv6, Static Routes, MPLS, Multicast VPN etc all complete

NS 179 - SITC of Indoor 802.11ac Wave 2 Dual-Radio Dual 5 GHz 3x3:3 MIMO Access Point for High Capacity Environments, with Integrated BLE radio and USB interfaces supporting IoT etc all complete

NS 180 - SITC of Wireless LAN Controller which can control up to 50 APs etc all complete

NS 181 - SITC of 100% Non Blocking Fully Digital Integrated Services Digital Network (ISDN) Compatible Voice Over Internet Telephone(VoIP) ready 19" Rack mountable EPABX presently equiped with 06 ISDN PRI Trunk Lines (180 Channel), 10 IP Extension, 16 Digital Extension, 250 Analogue Extension, Expandable up to 1000 Ports / Channels and other as per the given Specification etc. all complete

NS 182 - SITC of IP User Linceses for 10 Users etc all complete

NS 183 - SITC of 16 Port Digital Card etc all complete

NS 184 - SITC of 24 Port Analouge Card etc all complete

NS 185 - SITC of High End Digital Key Phone 6x24 Display with 24 Programmable Dual Color LED’s with 4 Feature Access Keys, multi-step Tilt angle adjustment, Navigator Key, backlit display, should have option to connect Blue Tooth etc. all complete.

NS 186 - SITC of Low end DIgital Key Phone 1x16 Display with 8 Programmable Dual Color LED’s etc. all complete.

NS 187 - SITC of IP Phone 1x16 Display with 8 Programmable Dual Color LED’s etc. all complete.

NS 188 - SITC of Analog Phone With Speaker , Small Display etc. all complete.

Audio Visual System

NS 189 - SITC of 98" Professional Display Panel, 4K UHD Resolution, 350 nits brightness, Contrast ratio 4000:1, Viewing angle 178 degrees h/v, Display colors 8 bit, 16.7 million, Input: 4 HDMI, VGA, DisplayPort, USB-C, Anti-glare treatment, 2 x 12W speakers etc all complete

NS 190 - 55" Display Panel, Resolution: 4K UHD (3840 x 2160p) Resolution, Direct-lit LED, Brightness: 500 nits, Contrast ratio: 1200:1, Display Colors: min 10bit, Input: 2 HDMI, DisplayPort, VGA, Audio In, Output- Audio output, Built-in OPS Slot, HDR10 Support, HDMI-CEC, 2 x 8W speakers etc all complete

NS 191 - SITC of 55" Commercial Grade LCD Video Wall Display Panel with LED backlight, Full HD (1920x1080) Resolution, Brightness 500 nits, Contrast ratio 4000:1, Viewing angle 178 degrees h/v, Portrait and landscape orientation, 1.7mm combined bezel to bezel, Input: 2 HDMI, DisplayPort, DVI, VGA and HDMI/DisplayPort Loop Output etc all complete

NS 192 - SITC of Ultra-Slim Pop-Out Videowall Mount, Recommended screen size: 42" - 70", Max load: 50kg etc all complete

NS 193 - SITC of Heavy Duty Universal Flat Screen Wall Mount, Recommended screen size: 65” up to 120", Max load: 200kg etc all complete

NS 194 - SITC of Universal Flat Screen Ceiling Mount, Recommended screen size: up to 65", Max load: 50kg, Ceiling Drop: 1m etc all complete

NS 195 - SITC of Slant mounting dusplay, screen size 55" etc all complete

NS 196 - SITC of High-quality PTZ camera with 20x Optical Zoom, Full HD 1080p60 with 1/2.8”high-quality CMOS sensor (2.07 Megapixel), High SNR CMOS combined with digital noise reduction, Output: 3G-SDI, HDMI up to 1080p60 and USB 2.0 up to 1080p30, VISCA, Pelco-D/P via RS232, RS485, Visca over IP, or IR, remote control, Up to 255 presets with 0.1° accuracy etc all complete

NS 197 - SITC of AV Bridge, Outputs simultaneous USB 3.0 and IP streaming with up to 1080p quality, Enables software-based video conferencing with Pro AV peripherals, HDMI input accepts 4K (3840 x 2160) signals and encodes and scales appropriately, PoE powered, Integrates with external DSPs by providing two balanced audio line inputs and outputs etc all complete

NS 198 - SITC of Mini PC, 8 GB RAM, 500 GB HDD, 4 USB ports, 2 HDMI/DisplayPort outputs, Integrated graphics card, Latest generation Intel i3/AMD equivalent with wireless keyboard and mouse etc all complete

NS 199 - SITC of Desktop Hidden Connection Box, Mechanical Locking Device, Smooth Pneumatic Support Structure, DisplayPort, HDMI, VGA, Audio, Network / Telephone, Power, Input voltage: 110V-220V / 50-60Hz, Mountable Enclosure for Cables etc. all complete.

NS 200 - SITC of Multiformat Transmitter, HDMI, VGA, DisplayPort, DVI-D and Audio inputs, Extends VGA, DVI, HDMI 1.4 or DP 1.1, Audio, Ethernet, RS-232, up to 120 Meter over one CAT5/6/7 cable, HDMI 1.4, HDCP 1.4 and DVI 1.0 compliant, HDBaseT compatible, Pixel Accurate Reclocking, Supports HDMI 3D signal formats, Bi-directional RS-232 and IR extension (pass-through and control), Supports HDMI 4K signal formats (4K UHD @30Hz RGB 4:4:4 or @60Hz YUV 4:2:0, up to 9 Gbps) etc all complete

NS 201 - SITC of Matrix Switcher of 4 HDBaseT , 4 HDMI Inputs, 2 HDBaseT and 2HDMI outputrs with audio outputs, 4K / UHD (30Hz RGB 4:4:4, 60Hz YCbCr 4:2:0), 3D capabilities and HDCP are fully supported, Built-in PoE injector, Balanced analog audio output for audio de-embedding, Built-in Event Manager control automation feature, HDBaseT compatible, HDMI 1.4, HDCP 1.4 and DVI 1.0 compliant, Pixel Accurate Reclocking, No video compression, Bi-directional RS-232 extension (pass-through), No signal latency, zero frame delay etc all complete

NS 202 - SITC of HDMI Transmitter, HDMI inputs, Extends DVI/HDMI 1.4, Audio, Ethernet, RS-232, up to 120 Meter over one CAT5/6/7 cable, HDMI 1.4, HDCP 1.4 and DVI 1.0 compliant, HDBaseT compatible, Pixel Accurate Reclocking, Supports HDMI 3D signal formats, Bi-directional RS-232 and IR extension (pass-through and control), Supports HDMI 4K signal formats (4K UHD @30Hz RGB 4:4:4 or @60Hz YUV 4:2:0, up to 9 Gbps) etc all complete

NS 203 - SITC of HDMI Reciever, HDMI inputs, Extends DVI/HDMI 1.4, Audio, Ethernet, RS-232, up to 120 Meter over one CAT5/6/7 cable, HDMI 1.4, HDCP 1.4 and DVI 1.0 compliant, HDBaseT compatible, Pixel Accurate Reclocking, Supports HDMI 3D signal formats, Bi-directional RS-232 and IR extension (pass-through and control), Supports HDMI 4K signal formats (4K UHD @30Hz RGB 4:4:4 or @60Hz YUV 4:2:0, up to 9 Gbps) etc all complete

NS 204 - SITC of Digital UHF Wireless Handheld Microphone System, Dynamic, 24 bit Digital Audio, Dynamic Range - 118 dB or better, Frequency Response : 20 to 20,000 Hz, Polar Pattern : Cardioid, Channels – Upto 30 simultaneous Channels per frequency bands, Switching Bandwidth - 42 MHz or better, Frequency Auto Scan Functionality, Range – 300 ft or more, RF Transmitter Output : 10 mW, Should have LAN port for monitoring, Should include rechargeable batteries and charger, Battery Life : 8 hours or more etc all complete

NS 205 - SITC of Digital UHF Wireless Lapel Microphone System, Condenser, 24 bit Digital Audio, Dynamic Range - 118 dB or better, Frequency Response : 20 to 20,000 Hz, Polar Pattern : Omnidirectional, Channels – Upto 30 simultaneous Channels per frequency bands, Switching Bandwidth - 42 MHz or better, Frequency Auto Scan Functionality, Range – 300 ft or more, RF Transmitter Output : 10 mW, Should have LAN port for monitoring, Should include rechargeable batteries and charger, Battery Life : 8 hours or more etc. all complete

NS 206 - SITC of Digital Conference System: Control Unit: Frequency response : must fall in audible range 70 Hz- 16 KHz, Total Harmonic Distortion : less than 0.1 %, Should control upto 250 conferencing inputs without any software or accessories, Analog In – Minimum 2, Analog Out – 4 or more, LAN Ports – 4 or more, TCP/IP port – 1 or more, Should inlcude power supply to power the required number of conference units, Should be able to prevent one mishap from taking down your entire system using redundant loop cable topology/ring topology, Four different microphone operating modes should be supported: Automatic,, First-In/First-On (FIFO), VOX (voice activated), and Manual etc all complete

NS 207 - SITC of Digital Conference System: Chairman Microphone Unit, Table Top Chairman Unit with 4 inch or more capacitive touch screen to vote, check participants information, view agenda etc., Delegate Off push button for switching off all active delegate microphone, Should Include detachable gooseneck microphone with length not more than 15” and have pickup area of 100-degree or less, Speak LED indicator for chairman microphone on, Frequency response : should fall in audible range 50 Hz – 17 KHz, Excellent RF Noise Immunity etc all complete

NS 208 - SITC of Digital Conference System: Delegate Microphone Unit, Table Top digital conference unit with Microphone On/ Off Push button to activate/deactivate the microphone, Request LED Indicator for microphone , Should Include detachable gooseneck microphone with length not more than 7” and have pickup area of 100-degree or less, Frequency response : should fall in audible range 50 Hz – 17 KHz, Excellent RF Noise Immunity etc all complete

NS 209 - Digital Conference System: Connecting cable for conference network, Cat6 STP, length 2m etc. all complete

NS 210 - Digital Conference System: Connecting cable for conference network, Cat6 STP, length 20m etc. all complete

NS 211 - SITC of Digital Audio Processor, 24 Channels of Total Analog Audio, 8 Configurable Flex Channels, 16x16 USB Audio Channels, 128x128 Network Audio Channels, 16 Channels of Routable AEC, Multiple Instance VoIP Lines, Single POTS Telephone line etc all complete

NS 212 - SITC of Type : Two - Way ceiling speaker with plastic back can, Cover/Material : Fire resistant plastic vented enclosure, metal grill, Speaker Unit : 5.5” with tweeter coaxial, Power Handling : 30W / 40W, Impedance : 70V / 100V / 8Ω, Sensitivity : 90dB, Frequency Response : 100-20KHz, Connector : Phoenix in/out, Tapings : 30w, 15w, 7.5w and 3.5w, Installation : Flush mount fast fit etc all complete

NS 213 - SITC of High Efficiency Class-D , Dual Channel Amplifier, Auto Sleep Function, Built-in Limiter Circuit, Dynamic Range - 116dBA, Output Resistance - 43 mOhm, Power Output (4 Ohms/8 Ohms/70V/100V) - 280W/245W/250W/240W, Frequency Response +/- 0.1dB 20Hz – 20kHz, Voltage Gain 32dB etc all complete

NS 214 -SITC of Enterprise-Class Control System, One RS-232/422/485 COM port, Two RS-232 COM ports, Eight IR/serial, eight relay, Programmable event scheduling with astronomical time clock etc complete

NS 215 - SITC of Apple iPad with GUI Application etc all complete

NS 216 - SITC of VGA+Audio Cable: 3 Feet etc. all complete.

NS 217 - SITC of High Speed HDMI Cable: 3 Feet etc. all complete.

NS 218 - SITC of High Speed HDMI Cable: 6 Feet etc. all complete.

NS 219 - SITC of High Speed HDMI Cable: 50 Feet etc. all complete.

NS 220 - SITC of 4K DisplayPort Cable: 3 Feet etc. all complete.

NS 221 - SITC of 16AWG 2 Core Speaker Cable (as per actual) etc. all complete.

NS 222 - SITC CAT6A cable F/UTP (as per actual) etc all complete

NS 223 - SITC of 2 Core Sheilded Audio/Control Cable (as per actual) etc all complete

NS 224 - SITC of Connector and Accessories etc all complete

NS 225 - SITC of Rack Structure 20 U Air Cooled AV Equipment Rack with 4 Nos. of Vertical Power Strips, Cantilever Selves, Cable routing perforations, 4 No. of Spin Wheels etc. all complete.

Operator Workstation

NS 226 - Client Workstation :- PC comprising i7 processor, 3 GHz, 16 GB RAM, 256MB SSD, 1 TB HDD, 1GB Graphic card, 52X CD RoM drive, USB Port, 21 inch LED display, keyboard, mouse and windows 10 operating system and anti virus software.

NS 227 - Laser jet Printer (A4 size, B/W)

BUILDING MANAGEMENT SYSTEM WEB-BASED SERVER SOFTWARE

NS 228 - Supply, Installation, Testing & Commissioning of software for Building Management Software with features like 3D vector dynamic graphics with Autocad import of plan with Zoom In & Zoom Out facility, Plant Viewer, Trend Viewer, Object Viewer, Report Viewer, Alarm router. The Web-Based Server software shall permit use of Standard Web-Browsers such as Microsoft Internet Explorer, Netscape Navigator, etc. The software shall be capable of integration third-party systems and should supports latest IP technology (IP V4/V6). The Management Stations shall match the BACnet Profile B-AWS (Advanced workstation) as per the BTL Listing. The Web based software shall include 1 Client License for remote viewing. The software shall have Online Engineering capability i.e. Zero Downtime for software graphics modification and multi monitor 4 simultaneous views of critical systems. The software shall be capable of integrating seamlessly with FAS System & should provide SMS/Email feature for accessing critical alarms on mobile phone. (Properitary Protocol shall not be accepted)

NETWORK SUPERVISORY CONTROLLERS) Compliant with ISO 16484-5 and BTL label (BACnet communications passed the BTL test)

NS 229 - Supply, installation, testing and commissioning of Microprocessor based 32 Bit ,UL Listed Web Based Supervisory controller for connecting all field DDC controllers and 3rd party System Integration Units and for transferring data from field devices to BMS Server Software. The Network Controller shall support routing between BACnet/IP , BACnet/LonTalk and BACnet MS/TP. The Router shall Supports BACnet/IPv4 & BACnet/IPv6 and Firmware update via Ethernet and USB Device. In case of PC/Software Failure, User can access the system using POT. Proprietry Protocol shall not be accepted between Router and Management station.

NS 230 - Supply, Installation, Testing & Commissioning of LCD Display type Portable Operator Terminal for Local Control & Monitoring by Operator at Field. The same should be able to provide dynamic response of the process variables graphically. Alarm monitoring with acknowledgement and visual and audible alarm indication. Pop up window with detailed message for alarms and events. Alarm and event history. Data point display and operation of all measured values, setpoints, plant states, operating states and parameters. Graphic based display and operation of all time schedules, exception calendar, online trending and heating curve. User specific configurable overview of main values in plant.

PROGRAMMABLE & APPLICATION SPECIFIC CONTROLLER (DDC) - UL LISTED/BTL certified.

NS 231 - Supply, Installation, Testing & Commissioning of Standalone, Intelligent, UL listed, BTL tested, ANSI/ASHRAE approved interoperable DDC as per the specification. All the controllers are UL/BTL tested & CE certified .The controller possesses Dual 32 Bit Microprocessor both for IO Management as well as communication. Bit Rate for Bacnet/IP Controller should be 100 Mbps autosensing. The storage capacity of the controller is 64MB SDRAM & 32MB FLASH. It should store trend logs and event buffer for a typical duration of upto 30 Days. DDC Controller shall have a resident real time clock with a battery back up. DDC must support trending & scheduling at Controller level.For Modular Chiller Plant Controller Analog IO Modules should have an option for local override facility . LCD display shall be as per OEM listed in Approved Make.(LO/ID to ISO 16 484-2) & Relay Modules should have override as per ISO 16 484 2 . There should be minimum spare capacity of 10 % points. The controller shall be housed in a vandal proof, lockable & secure MS cabinets along with all necessary switchgear protections as required. Please Note: Manufacturer self-declaration PICS is required prior to executing work to gain information on the type of communication for the building automation and control system.

The above shall be housed in a vandal proof, lockable & secure MS Cabinets to be supplied along with all necessary switchgear protections as required.

NS 231.1 - DDC for Chilled Plant Manager includes Chiller, Primary, Secondary, Condensor, Cooling Tower, Hot Water Generator & Pumps - The DDC shall have optional Analog IO Modules which should have local override facility. LCD display shall be as per OEM listed in Approved Make. (LO/ID to ISO 16 484-2) & optional Relay Modules should have override as per ISO 16 484-2)

NS 231.2 - DDC for Air Handling Units (Maximum 2 AHU in 1 DDC)

NS 231.3 - DDC for Electrical System

NS 231.4 - DDC for Plumbing System

NS 231.5 - DDC for Fire Fighting System

SYSTEM INTEGRATION UNITS for 3rd party integrations - UL listed Controllers & BTL label

NS 232 - Supply, Installation, Testing & Commissioning of System Integration unit consisting of microprocessor based controller units BTL & UL Listed for third party integration. The same should support operations/ monitoring via portable operator terminal. The controller shall be Native BACnet type with communication via BACnet/LonTalk, Integration platforms and system controllers for third-party devices and systems via KNX, Modbus, M-Bus and other protocols into the automation level via BACnet. The same shall Support operation via local or network-compatible operator units. It should store trend logs and event buffer for a typical duration of up to 30 Days. Thirty Party make controller shall not be accepted.

NS 232.1 - Integrator of Chillers & Secondary Pumping, Cooling Tower integration on Bacnet/MSTP or Modbus Protocol

NS 232.2 - Integrator of AHU VFDs on Bacnet/MSTP or Modbus Protocol

NS 232.3 - Integrator of DG on Modbus RTU with RS 485 Communication Port

NS 232.4 - Integrator of MFM for LT Panels - 14 No's

NS 232.5 - Integrator of UPS on Bacnet/IP, Bacnet/MSTP or Modbus Protocol

NS 232.6 - Integration of Fire Alarm System on Bacnet/IP Protocol

NS 232.7 - Integration of Access control system on Modbus/TCPIP

Field instruments

NS 233 - Supplying, installing, testing and commissioning of the following sensors / transducers / transmitters

NS 233.1 - Supply, Installation, Testing & Commissioning of Immersion temperature sensor 100 mm Pt1000 with Brass Thermowell.

NS 233.2 - Supply, Installation, Testing & Commissioning of Outside air temperature + humidity sensors for measuring outside air temperature. It should be provided with sun sheild and rain protection.

NS 233.3 - Supply, Installation, Testing & Commissioning of Clampon Type Electromagnetic Water Flow Meter.

NS 233.4 - Supply, Installation, Testing & Commissioning of Water Flow Switch

NS 233.5 - Supply, Installation, Testing & Commissioning of Differential pressure sensor for liquids (0…10 V)

NS 233.6 - Supply, Installation, Testing & Commissioning of Water Level Switch.

NS 233.7 - Supply, Installation, Testing & Commissioning of Differential pressure switch for Blower/Filter Status (Pa Range 20…300…500 Pa)

NS 233.8 - Supply, Installation, Testing & Commissioning of Duct temperature sensor, Pt1000 element for Temperature Monitoring.

NS 233.9 - Supply, Installation, Testing & Commissioning of Duct temperature & RH Sensor

NS 233.10 - Supply of Current Relay

NS 233.11 - Supply, Installation, Testing & Commissioning of Flameproof Level Switch.

NS 233.12 - Supply, Installation, Testing & Commissioning of Voltage Transducer

NS 233.13 - Supply, Installation, Testing & Commissioning of Bi Level Switch

NS 233.14 - Supply, Installation, Testing & Commissioning of Pressure sensor for neutral and slightly aggressive liquids (0…10V).

Cabling and Conduiting

NS 234 - Supplying & laying of signal cables. (2 core x 1.5 Sq.mm), PVC insulated, Shielded tinned copper conductor cable.

NS 235 - Supply & Laying of GI Flexible

WATER COOLED WATER CHILLING MACHINES :

NS 236 - Supplying, installing, testing & commissioning of microprocessor controlled variable speed Screw Type water chilling machine each having a minimum actual capacity of 180 TR at chilled water inlet/outlet temperature of 54 deg.F/44 deg.F, Fouling Factor 0.0005 FPS with chilled water circulation rate of 432 USGPM and condenser water inlet/outlet temperature of 90 deg.F/ 97.5 deg.F ,Fouling Factor 0.001 FPS with circulation rate of 692 USGPM, suitable for operation on refrigerant R-134a for semi hermetic screw type each comprising of the following complete as per specifications and as required. NPLV shall not exceed 0.38 and IKW/TR 0.71 at reducing condenser water temperature as per AHRI 550/590 standard. Chiller performance should certify with AHRI 550-590. Performance testing on AHRI certified test bed at 100% load of one machine at manufacture works on AHRI certified test bed. The COP of the machine should not be less than 5.4. IPLV SHALL BE MINIMUM 6.5. Mono / twin Screw Type Compressor in semi hermetic construction, complete with automatic steeples type capacity control, safety switches, forced feed lubrication system etc., as per specifications. Suitable Nos & suitable capacity squirrel cage induction motor with class 'F' insulation suitable for operation on 415 volts +10%, 50 Hz, A.C. supply. Suitable Nos. & suitable capacity Air Cooled VFD starter suitable for compressor motor complete with ammeter, over load protection, under voltage protection, protection against phase reversal & independent single phase preventers etc. complete as required. The VFD shall be installed inside the panel/ in case VFD is installed separately the same shall be IP 54 rated.

Necessary drive arrangement.-1 Set – Lubrication device,oil strainer, automatic pressure regulating valve, oil heater, oil heater thermal sNecessary drive arrangement.-1 Set – Lubrication device, oil strainer, automatic pressure regulating valve, oil heater, oil heater thermal switch etc. as per specifications. 1 No. – Matching shell and tube water cooled condenser of M.S. shell and integrally both side finned copper tubes. The pressure drop across condenser should be as per CPWD Standard. 1 No. – Matching shell & tube flooded type chiller for screw type units of MS shell and integrally both side finned copper tubes the pressure drop across cooler should be less than 5 meter. 1 Lot – Refrigerant piping fittings, valves and accessories to inter connect compressor, condenser, chiller and expansion valve. The expansion valve shall work on level sensing technology. 1 Set – Microprocessor based control panel (Modbus and BACnet protocol compatible) compete with accessories and inbuilt OEM provided remote monitoring facility for the remote access for the chiller by OEM as per the specification. as per specifications. 1 Lot – Refrigerant line accessories comprising of safety valves, angle valve, liquid line indications, liquid level control etc. 1 Lot – Water flow switches at outlet of condenser & chiller, water drain and air purge valves wherever required.. 1 Lot – Suction line and chiller insulation (OEM provided factory installed) with minimum 19 mm thick polyvinyl nitrile rubber insulation complete as required. 1 Lot –Frame work for mounting the above condenser, chiller compressor and motor with base plate complete with ant vibration pads/springs. 1 Lot – Initial/first charge of refrigerant gas and compressor oil. 180 TR Screw Chillers with VFD.

Hot water Generators

NS 238 - Supply,installation, testing & Commissioning of electrically operated Hot Water Generator of of following actual capacity made of 8mm M.S. sheet and dish end made of 10mm M.S. having 16 gauge stainless steel lining with heaters arranged in banks and Controller and Thermostat so that required qty. of hot water is generated at 50°C with nominal variation, including 100mm thick resin bonded fibre glass insulation of 24 Kg / CUM density finished with 1.25mm thick aluminium sheet cladding including necessary Electrical panel with BMS compatible having suitable Incoming and outgoing Switchgears for Boiler, automatic Controls including inlet and outlet connections for water complete with pressure release valve, low level cut-out, Autovent sight-glass as per specification complete as required. (Degree of protection IP52 with IS 2147) - 150 KW

Heating capacity : 150 KW (1W+1SB)

Water in temp. : 45 deg C

Water out temp : 50 deg C ,Flow Rate : 140USGPM

Condenser water Pumps Set

NS 239 - Supply, erection, testing and commissioning of Centrifugal Vertical Split Casing condenser water pump set capable of delivering 692USGPM of water against 28 mtr head each comprising of the following and complete as per specifications and as required. 1 No. - Split Casing/end suction back pull out type pump with bronze impellar, S.S Shaft, Suitable Coated CI body and mechanical seal.1 No. - Split Casing/end suction back pull out type pump with bronze impellar, S.S Shaft, CED Coated CI body and mechanical seal.1 No. Suitable HP, TEFC squirrel cage induction motor with class 'F' insulation,Eff-2, 1450 RPM synchronous speed, operating on 415 Volts ± 10 %, 3 phase, 50 Hz A.C. supply. Unless otherwise specified, renewable wear ring of bronze shall be furnished atleast on the casing

Pump as above (2 working+1 Stand by)

Chilled water Primary Pumps

NS 240 - Supplying, erection, testing and commissioning of Centrifugal Vertical Split Casing/ primary chilled set capable of delivering 432USGPM of water against a head 20 Mtr. each pump shall comprise the following as required as per specifications.1 No. -Vertical Split Casing type pump with bronze impeller, S.S Shaft, Suitable Coated C.I body and mechanical seal.1 No.- Suitable HP, TEFC squirrel cage induction motor with class 'F' insulation,IP -55 Protection, IE3 MOTORS, 1450 RPM synchronous speed, operating on 415 volts ± 10%, 3 phase, 50 Hz A.C. supply. Pump as above (2 working+1 SB)

Secondary pump

NS 241 - Supplying, erection, testing and commissioning of Centrifugal Vertical split casing Secondary chilled , comprising of:Pumping set with Suitable Coated cast Iron casing, Bronze impellers with stainless steel shaft, connected to suitable capacity TEFC ventilated induction motor with class 'F' insulation, IE-3 motor, 3 Phase, 1450 RPM, suitable for 415 volts ± 10%, 3 phase, 50 Hz A.C. supply. Renewable wear ring of bronze shall be furnished atleast on the casing . Pump shall follow following duty with following no. of pumps:Flow Rate : 432USGPM , Head : 28 Metre WC

Hot Water Pump Sets

NS 242 - SSupply,erection, testing and commissioning of end suction back pull out type Hot water centrifugal pump for hot water recirculation, pump set capable of delivering 140 USGPM of water against 30 mtr head each comprising of the following and complete as required 1 No. - centrifugal type pump with bronze impellar and mechanical seal.1 No. Suitable HP, TEFC squirrel cage induction motor(Eff-1) with class ' B' insulation, 1500 RPM synchronous speed, operating on 415 Volts + 10 % , 3 phase , 50 Hz A.C. supply. (1 working+1 stand by )

Cooling Towers

NS 243 - Supply, installation, testing and commissioning of FRP Induced draft Cross / Counter flow, 1 to 4 fan as required direct / gear driven site erected cooling tower of capacity as mentioned below based on the parameters given below and complete with PVC Fill Louvers Drift Eliminator Weather proof IP 55 TEFC Motor ( IE-3), Propeller Fan FRP basin with additional sump in the bottom of the basin on every outlet point to avoid vortex formation in the condenser water pipe line Hot dip galvonized Steel Ladder, Stainless Steel hardware including nut, bolt, washer etc. The cooling Tower shall confirm to technical specification given in the tender The maximum allowable sound power at distance of i M from the cooling Tower shall be less than 75 dB. Tower fan motor shall besuitable for VFD operation and operation of VFD system shall be approach of cooling towerm with separate isolator / MCCB etc. as required.Cooling Towers 6.45 lacs kcal/hr heat rehection capacity. Water Leaving Temperature : 32.3 Deg C, Water Entering Temperature : 36.4 Deg C, Water Flow Rate : 692USGPM , Ambient Wet Bulb Temperature : 28.3 Deg C, Cooling Tower as Above ( 2 working+1 stand by)

FLOOR MOUNTED/ CEILING SUSPENDED AIR HANDLING UNITS :

NS 244 - Supply,installation,testing and commissioning of sheet metal sectionalised construction draw thru type in Double Skin construction with 275 GSM galvanized inner coating for corrosion resistance and with CFC-free PUF insulation of 42 kg/Cum injected between with an integral gasket between the both skin , inner and outer sheet made of 0.63 mm thickness of pre coated galvanized sheet . entire fan assembly shall be supplied with base fram and shall be mounted on suitable spring isolators to minimize the vibration . Mixing box if required .Cooling coil /heating coil as per datasheet and specification . Fan shall be as per the specifications and shall be plug fans duly certified with AMCA/EUROVENT for air and sound performance .Motor shall be of IE-3 efficiency . Each Air Hndling Units shall be with filter sections , coil size shall be at face velociy of 500 FPM, 6 row deep cooling coil .Motor shall be suitable for 415V/3Ph/50 Hz AC electric supply.AHU shall be complete with accessories , supports , vibration spring isolators, insulated drain pan , access panel for fan motor , filter cleaning /replacement . etc in all respect. Any other detail shall be as per specification , datasheet and drawings .

ALL OTHER AHU DETAILS SHALL BE AS PER DBR DATASHEETS AND SPECIFICATION

AIR HANDING UNITS - CEILING SUSPENDED UNITS

NS 244.1 - 3000 CFM-65 MM ESP , 7 TR

NS 244.1 - 3000 CFM-65 MM ESP , 7.5 TR

NS 244.4 - 3300 CFM-65 MM ESP , 8.8 TR

NS 245 - Supply, installation, testing and commissioning of Pump Logic controller (Control Panel-Variable secondary Panel should have a dedicated programmable logic controller with individual drive for each pump and with required no. of sensors and the entire unit has to be procured from the Pump manufacturer to ensure the smooth operation of the system. The Programmable logic controller shall be able to control minimum 1 Pump and maximum of 4/6 Pumps. Microprocessor based control panel shall have suitable hardware & software so that it can be integrated directly to IBMS with standard communication open protocol using backnet / Modbus as well as open IP.), 3*15kW VFD and DPT - 2 Nos (Necessory 2 nos. of Ectronic Differential Pressure Transmitters and control wiring (control wiring is quantified in electrical Sub head) as required) for Secondary Pump (To be provided with conjunction of NS Item No.-241) .

NS 246 - Supply, installation, testing and commissioning of ceiling suspended FCU's static pressure shall be max 5 mmwc, each complete with 3 row deep cooling coil of copper tubes aluminium fins construction, centrifugal fan, 3 speed motor, filters insulated drain pan, coil piping connections, condensate drain connection, manual air vent valve, SP isolator with MS enclosure box should be Provided etc. as required as per specification & drawings with the following capacities:-

NS 246.1 - 2.0 TR-800 CFM

NS 246.2 - 2.5 TR-1000 CFM

NS 246.3 - 3.5 TR-1400 CFM

NS 247 - VARIABLE FREQUENCY DRIVES-Supply, Installation, testing & commissioning of HVAC dedicated VFDs suitable for the following AHU fan motor capacity (The integration of the VFD with AHU is included in this item) with IP 54/55 enclosures with Mains disconnect, complying with the tender specifications and having:Built-in dual 5% impedance DC link reactor (harmonic filters) on the positive and negative rails of the DC bus of the VFD. Built-in EMC Filters (electromagnetic compatibility filters) for VFDs for restriction of conducted emissions to comply with IEC61800: 3 (unrestricted distribution): 2004 Category C 1/C 2, for required length of cable between motor & VFD.Two/Three -feedback PID (Propotional integrated derivative) controller having capability to simultaneously accept 2/3 feedback signals from temperature sensors for process optimization and accordingly regulate the speed of the AHUs.Automatic Energy Optimization for maximum energy savings. 3.7 KW

NS 248 - Supply, Installation, testing and Commissioning of ceiling / floor mounted Rectangular/ROUND box type accoustically insulated centrifugal Inline fan, constructed of GSS duly powder coated as per detailed specifications, complete with forward curved DIDW fan, motor and drive suitable for 220 ± 10% volts, 1 phase, 50 Hz A.C supply, with necessary canvas connection etc complete in all respects. for toilet exhaust 500 cfm at 15 mm static

NS 249 - Supplying, installation, testing & commissioning of Propeller type exhaust air fans suitable for following capacities complete with electric motor suitable for operation on 220 V+ 10%,50 Hz, 1 phase AC supply fitted with speed regulator, mountings, frames, louvers and bird screen etc. of the following capacities.e unit shall be complete as per drawings and specifications. 200 mm dia

Main HVAC Panels

NS 250 - Supply, installation, testing and commissioning of the following integrated cubical type dead front extensible sheel control panel, anchoring of panel to foundation. The panel shall be suitable for 415Volts/3Ph/50Hz. Quoted price shall also include Ruber Mats etc. The Panel shall have separate compartment for bus bar and cable alleys. The following components and accessories ashall be mounted within each control pane.

INCOMER

Two set of 1250 Amps Electrically operated draw out type 4 pole ACB with 6 NO & 6 NC contacts and complete with the following

Overvoltage tripping mechanism for persistent voltage exceeding 110% of the rated voltage for more than 5 minutes

CT operated over current and earth fault relay(IDMT) with CTs 4000/5A SP 10 protection class VA burden

Phase indicating Lamps with toggle switches and control fuses.

BUS COUPLER - 1 No 1250 Amps ACB with ON/OFF and trip indication .

Bus Bars :

Aluminium Bus bar with heat shrinkable sleeves rated at1600 Amps for 3 ph and neutral phase. Bus bar shall have maximum current density of 0.8amps/mm2 and the neutral phase bar of not less than 50% capacity 1600A EP ACB for Bus Coupler

Outgoings:

1 nos. 160 Amps contactor with TP MCCB 160 A with neutral link outgoing feeders for sec. chilled water pump motor. The compartment shall contain CT operated multifunction meter and indicating lamps with fuse and toggle switch for ON and Trip status .

Total Panel Price

Control Panel in Air Handling Units (AHUs) :

NS 251 - Supply,installation,testing and commissioning of the following Cubical type openable front , sheet steel wall mounted control panels sleeve type. Al. bus bars including anchoring inton the wall. These panels shall be completer in all respect as per the drawing and specification.

The panel shall include the following accessories :

MCCB as per rating given below.

Terminal block for power distribution.

Single Phase Preventor.

Phase indicating lights and indicating lights for ON/TRIP status

Time delay relay for automatic restart of AHUs motors.

All starters shall have suitable potential free contacts

Wiring for microswitch for stopping the fan when fire dampers closes.

The number of AHU panel shall be as detailed below :

32 amps TP MCB with 1 No. 5.0 HP DOL starter

Condenser Water Piping :

NS 252 - Supplying, fixing, testing and commissioning of condenser water pipes of following sizes of MS 'C' class along with necessary clamps, vibration isolators and fittings such as bends,tees etc.but excluding valves, strainers, gauges etc.adequately supported on rigid supports duly painted / buried in ground excavation and refilling etc.as per specification and as required complete in all respect. Note:- The Pipes size 150mm & below shall be M.S.'C' class as per IS:1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS:3589, from minimum 6.35mm thick M.S. Sheel for pipes upto 350 mm dia.And from mininum 8mm thick MS sheel for pipes of 400 mm dia and above. 50 mm dia

Condenser Circuit Valves without insulation

NS 253 - Supply,fixing,testing and commissioning of following size valves, guages and strainers for condenser water circulation as per drawings and specifications Butterfly Valves (manual) with CI body SS disc nitrile sheet and O ring PN 16 250 mm dia

NS 254 - Supply,fixing,testing and commissioning of flow switch

NS 255 - Supply ,Installation ,Testing and commissioning of Y -STRAINER of ductile body flanged ends with stainless steel strainer for condenser water piping without insulation as specified . - 200 mm dia

NS 256 - S/F of POT STRAINER - 250 MM DIA as show in drawing

NS 257 -Supplying,fixing,testing and commissioning of following valves, strainers,gauges in the chilled / hot water plumbing duly insulated to the same specifications as the connected piping and adequately supported as per specifications

Butterfly Valves /Ball valves(Manual) with CI body SS Disc, Nitrile Rubber seal and O- ring PN16 pressure rating for chilled water / hot water circulation as specified.

NS 257.1 - 32 mm dia. BALL VALVE

NS 257.2 - 25 mm dia. BALL VALVE

NS 257.3 - Ball Valve set with Y stainer duly insulated of the following sizes as per specifications and drawings. -32 mm dia

NS 257.4 - Ball Valve set with Y stainer duly insulated of the following sizes as per specifications and drawings. -25 mm dia

NS 258 - BALANCING VALVE WITH BUILT IN MEASURING FACILITY with C I body flanged construction with EPDM coated disc with long pitch with protected out pipe insulation & PN 16 pressure rating for chilled / hot water circulation as specified - 25 mm dia - brass /bronze

NS 259 - Supply ,Installation ,Testing and commissioning of Flexible connector for following Dia. pipe suitable for PN 16 pressure rating to be installed at pump and chiller suction and discharge .

NS 259.1 - 200 mm dia

NS 259.2 - 150 mm dia

NS 259.3 - 100 mm dia

NS 260 - Supply, Installation, testing and commissioning of thermostat for HEATING AND COOLING APPLICATION FOR various air handling Units AND FCU.

NS 261 - Two Way Motorized Valves with modulating motor actuator & transformar for converting AC to DC, in heating coil of air handling units as per specification gof following sizes. -25 mm dia

Close Type Expansion Tank & Air separator :

NS 262 - Supply,installation,testing and commissioning of close type expansion tank of 1000 litres capacity with EPDM butyle membrane tested at minimum 16 bar pressure complete with its pressurisation unit with double pump and its suitable panel and required accessories for proper installation and working as per drawings specifications. (for chilled water circuit)

Combined Air and Dirt Separators

NS 263 - Supply, Installation, testing and commissioning of a combined Air and Dirt Separators as per Specifications on the return water line located at the pump suction or a suitable location in AC Plant Room as suggested and suitable for 900 gpm water flow. Separator should be capable of removing all micro bubbles and should have a steel tube & copper wire media to carry out its operation. It should be able to remove upto 10 microns of dirt particles. The separator should be complete with high capacity air vent, service valve, non return valve, butterfly valve connection for makeup water inlet, flanges, drain valve etc

Drain Piping :

NS 264 -Supply,installation,testing and commissioning of condensate drain water piping of GI ' Medium' Class complete with fittings like elbow, tees, reducers bends M.S. flanges, Supports welding, Painting etc. as required confirming to tender specifications and of following size.

NS 264.1 - 65 mm dia

NS 264.2 - 50 mm dia

NS 264.3 - 40 mm dia

NS 264.4 - 32 mm dia

NS 264.5 - 25 mm dia

NS 265 - Supply,installation,testing and commissioning of Air Vents 15 mm dia.

NS 266 - S&F of 1" dia Ball valves for drain with fittings etc.

Underdeck Insulation of Exposed Roofs:

NS 267 - Supply and fixing thermal insulation on exposed roof ( underdeck) with 13mm thick Cross Linked Closed Cell Polyethylene FR-XPE insulation of density 33 kg/cub.mtr with adhesive (pidilite SR-505) etc. as required and finally fixed with the help of rawl plug & dash fastners.

AIR PURIFICATION SYSTEM ( UVGI SYSTEM FOR AHUS)

NS 268 - Supply, installation, testing and commissioning of comprehensive Air purification system in the specified areas where AHU units etc are installed, so as to improve Indoor air quality by using combination of needle point, Tube type & Carbon Brush Type Bi-polar ionizers would not have any consumables and would have a life of 10 years. Project design would meet standard ASHRAE 62.1 IAQ Procedure for energy saving. System would kill microorganism and pathogens, remove odour, VOC and reduce dust particle/particulate matter/PM2.5/PM10. The product would be UL/Intertek listed. Product would have minimal or negligible pressure drop & low power consumptions. Product would have UL 867 and UL 2998 certification (for zero ozone emission). The product shall have been tested on COVID-19 surrogate for its efficacy.

NS 269 - SITC OF 1 Floor Mounted, bottom discharge Air Cooled DX type 4.0 Tr Precision Air Conditioner. The unit shall be self-contained direct expansion type Precision air conditioning units suitable for operation on R407c refrigerant & have advanced microprocessor and electronically communicated. Modular construction Precision air conditioning unit with R-407c refrigerant, bottom discharge arrangement consisting of inlet filter, blow through direct drive Electronically communicated Motors and Backward curved Plug fans, fan motor assembly to deliver desired air quantity, Scroll Compressor, Direct Expansion Cooling Coil, Heater to maintain humidity inside the space, condensate drain pan of stainless steel construction, Microprocessor panel, programmable control complete with LCD display. The Outdoor Condenser unit shall comprise of Condenser fans & motor, Condenser cooling coil (Copper coil with aluminium fins), Fan speed controller, Isolater switch. The unit shall be suitable for operation on 415 Volts, 50 Hz, 3 Phase, 4 Wire AC supply. Each unit should be having individual display panel, which shall display date, time, actual & set values, operating conditions, signal faults, collective faults, limiting values and PAC wellness alarm / service alarm to reduce the down time. Items included are: Scroll Compressor EC Fan with Motor Evaporator Cooling Coil Air cooled condenser with Fan Speed Controller Microprocessor (Carel) C5-12 Electric heater & Steam Humidifier Power Panel & starter for all drives G4 Filter RS485 Modbus Protocol to connect with BMS Team Mode feature for PAC units controller for synchronising the Multiple No. of units to work as single system for all above units. Load sharing mode & Sequencing feature Supply of 4.0 Tr PAC Unit as per above specification. Item included low side accessories and Installation and commissioning. 4 TR

Axial flow Fan for EXHAUST air Supply :

NS 270 - Supply, Installation, Testing & Commissioning of GSS long casing (Motor should completely coverd in fan casing) tube Axial flow type fans for parking ventilation exhaust fans and smoke exhaust fans for corridor complete with aluminium alloy blades with aerofoil design, bird screen,fire rated flexible connection & gravity louvers , vibration isolators at outlet. Motor shall be of 415 + 10% volts, 50 Hz. Sound level at 3mt distance from fan outlet shall not be more than 80db(A) (Room Condition). Capacity shall be as follows & as per detailed technical specification: Fans should be AMCA certified. RPM Should be as per manufacturer standards.However lower CFM fans upto 5000 CFM can be provided at 2850 Rotations per minute. Outlet velocity shuld not exceed 10 m/s of below capacities. fans shall be fire rated (250 deg c for 2 hours).

NS 270.1 - 10000 cfm at 20 mm static car park exhaust fans

NS 270.2 - 10000 cfm at 25mm static - typ coriidor smoke extraction

NS 271 - Supply, Installation, Testing & Commissioning of GSS long casing (Motor should completely coverd in fan casing) tube Axial flow type fans for parking smoke fresh airand staircase pressurization , stair well pressurization , lift lobby pressurization fans for areas mentioned in datasheet complete with aluminium alloy blades with aerofoil design, bird screen, flexible connection & gravity louvers at outlet. Motor shall be of 415 + 10% volts, 50 Hz. Sound level at 3mt distance from fan outlet shall not be more than 80db(A) (Room Condition). Capacity shall be as follows & as per detailed technical specification: Fans should be AMCA certified. RPM Should Not exceed 1450.However lower CFM fans upto 5000 CFM can be provided at 2850 Rotations per minute. Outlet velocity shuld not exceed 10 m/s of below capacities.

NS 271.1 - 10000 cfm at 25 mm static - 2nd basement fresh air , staircase pressurization , lift lobby pressurization

NS 271.2 - 3000 cfm at 25 mm static -stairwell pressurization fan

CO / CO2 System For Parking Ventilation Normal Mode Fans for Supply & Exhaust

NS 272 - Supply, installation, testing and commissioning of CO & CO2 system for on/off the motor of parking ventilation supply and exahust fans for normal mode operation. Each exahust fan shall be hooked with minimum 02 nos. CO sensors (as per tender specification) with minimum 01 nos. BMS compitable digital programmable touch screen control panels with controller (with 5 AI, 12 DI, 2 AO, 4 DO as per IO Summary given in specification per Zone) loaded with software to give the average outcome command simultaneoulsy to exhaust and supply fan motor drive.

The rate shall be inclusive of 2Cx0.5 Sqmm communication copper cable of shielded and twisted type in 25 mm PVC conduit of length 100 running meter approximately and other associted item as required to suit the site conditions etc. Each control panel shall be with all accessories including necessary switchgear, step down transformer, internal power and control cabling done and complete in all respect & as required to suit the site conditions etc. Sensor shall have following measuring range & accuracy:-

CO - Minimum measuring range : 0 ~ 300 ppm, CO2 -Minimum measuring range : 0 ~ 5000 ppm & Accuracy < 1% of measuring range.

Each zone shall have controlled ventilation rate of 25% of the specified fan capacity at a given frequency, When CO measurement is below 25 ppm or CO2 is below 1500 ppm & Ventilation rate shall increase proportionally & when CO level increase beyond 25 ppm or CO2 above 1500 ppm and reach the maximum fan capacity when CO level is above 50 ppm or CO2 above 3000 ppm. User should be able to vary these setpoints through manually. Controller shall also have the logic to switch ON the fan when CO is above 9 ppm or CO2 is above 1000 ppm & switched OFF again when CO drops below 6 ppm or CO2 is below 600 ppm. Controller shall also have the facility of timer & manual override for fan operation.

Above system should include 16 nos CO sensor , 16 no CO2 sensor , PLC panel , control wiring between CO sensors and fan ventilation panel

AIR DISTRIBUTION WORK

NS 273 - Supplying & fixing of powder coated extruded aluminium Return Air Grills with louvers but without volume control dampers complete as required.

NS 274 - Supply,installation,testing and commissioning of MS powder coated Exhaust /fresh air Grilles/louvers without dampers but with wire mesh jali for exhaust.

NS 275 - Supply, installation, testing and commissioning of fresh air/ exhaust air Louver comprising of powder coated GI louvers with bird screen as required.

NS 276 - Supply, installation & testing of GI back draft dampers (16 G Blade & Frame) similar constrction to gravity louvers (for Basement fans- fire case as specified in the drawing.) , provided with suitable links to prevent the back pressure of air.

Basement Ventilation Panel

NS 277 - Supplying, of dust, damp and vermin proof free floor mounted, Indoor type standing factory built sheet steel enclosed modular construction extendable panel, suitable for operation on 415 ±10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with CRCA sheet steel of 2mm thick for frame work and covers, 3mm thick for gland plates i/c cleaning & finishing complete with 7 tank process for powder coating in approved shade, complete with Aluminium bus bars, inter-connection with copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required.

including control wiring with 1.5sqmm. & 2.5sqmm. PVC insulated FRLS copper conductor S/C cable for voltage & current respectively, cable alleys, cable gland plates in two half, etc. necessary metering protections & indications and mounted with the following switch gears as per drawing and technical specifications etc. complete as required. ( Each starter should have remote control and interlocking facilities including auto manual switch, NO/NC contacts for control and must have auto manual operation suitable to take signal from fire alarm panel for automatic operation of fan in case of fire. All the starters shall have suitable facility to operate with fire sensing control modules.

corridor and staircase pressurization fan panel

NS 277.1 - Incoming:

320 Amp TPN MCCB (35 KA) (Ics=Icu upto 433 V) thermal magnetic release with over current and short circuit releases, all indication, front operating handle & door interlock )

3 Nos. Phase indication LED lamps with 2 Amps back up MCB, breaker ' ON/OFF' indicating light with 2A MCB

1 No. Intelligent multi-function digital panel meters of class 0.5 accuracy with communication interface port RS 485 for recording V (Between Phases and between each phase and neutral, A (In each phase and neutral), KWHr with suitable rating CTs, CT shorting links, R,Y, B LED indicating lamp and 2 A control SP MCB's.

Bus Bar :

TPN aluminium extensible type main bus bars of minimum of 500 Amp capacity and auxiliary bus bar of suitable capacity with heat shrinkable coloured sleeves and i/c DMC/ SMC bus bars supports at required intervals complete for cross section, size supports & their spacing etc.

Outgoings:

Ventilation Panel as above

Basement Ventilation Panel

NS 277.2 - Incoming:

400 Amp TPN MCCB (35 KA) (Ics=Icu upto 433 V) thermal magnetic release with over current and short circuit releases, all indication, front operating handle & door interlock )

3 Nos. Phase indication LED lamps with 2 Amps back up MCB, breaker ' ON/OFF' indicating light with 2A MCB

1 No. Intelligent multi-function digital panel meters of class 0.5 accuracy with communication interface port RS 485 for recording V (Between Phases and between each phase and neutral, A (In each phase and neutral), KWHr with suitable rating CTs, CT shorting links, R,Y, B LED indicating lamp and 2 A control SP MCB's.

Bus Bar :

TPN aluminium extensible type main bus bars of minimum of 500 Amp capacity and auxiliary bus bar of suitable capacity with heat shrinkable coloured sleeves and i/c DMC/ SMC bus bars supports at required intervals complete for cross section, size supports & their spacing etc.

Outgoings:

1 no PLC panel that should take input from 16 no of CO sensors and based on CO ppm inputs it should give signal to 12 no basement ventilation fans and 16 no dual speed jet fans .

Ventilation Panel as above

NS 279 - Design, supply and installation of steel structure work for DG exhaust piping as per drawings including painting work etc as required at site. The design of exhaust structure is covered in the scope of work.

NS 280 - Supply, installation, testing and commissioning of water softening plant of 25000 litter per day capsity for HVAC system as per below specification.

Raw Water pump 1 W & 1S - ( 8.0 M3/Hr) - 25 mt head - kirloskar pump /Crompton /CRI - 2 Nos.

Antiscalent Dosing System- Flow Rate : 0-4 LPH, 100 lits Tank - hypodosing , PH CORRECTION - 2NOS -CDS 2 - 3 Nos.

Multigrade Filter- Flow Rate : 3500 LPH,Material of Construction : FRP ,Vessel size : 24''(dia) x 72'' (ht)- NGMF -85 - 1 No.

Activated Carbon Filter- Flow Rate : 8000 m3/hr flow rate, Material of Construction : FRP ,Vessel size :24''(dia) x 72'' (ht)- NGMA -65 - 1 No.

Softner Plant - Flow Rate :8000 LPH,Material of Construction : FRP ,Vessel size : 21''(dia) x 62'' (ht) , NGS -9B ,RESIN QUANTITY - 300 KGS - 1 No.

4 M3 RO - 8 INCH -`4 ELEMENTS , AVERAGE RECOVERY 50 TO 60 % , MAX FEED TDS - 3313 , 250 PSI RATING , CONTROL PANEL -200 SERIS , CARTRIDGE FILTER- PP, PERMEATE PVC PIPE WORK -- 1 No.

I/c pipework (PVC from MGF inlet to RO OUT LET ) .Battery limit 1m from inlet of MGF - 1 No.

MCC Panel ,Cabling provision with level float switch for pump . - 1 No.

Operation of Electro Mechanical system ( As per BOQ) for defect liability period.

NS 281 - Operation and routine maintanance of Electro-Mechanical Services and other facilities as detailed in BOQ for 1st Year i.e., Defect Liability Period having HVAC System, 11/0.433KV Substation & DG Set, Lift, Fire alarm and Fire Fighting System IBMS System, Solar Panel/Solar Work, Sewage Treatment Plant, Water Supply etc as specified in the BOQ .

Operation and Comprehensive maintanance of Electro Mechanical system ( As per BOQ) after Defect Liability period

NS 282 - Operation and Comprehensive maintenance of Electro-Mechanical Services and other facilities as detailed in BOQ including providing replacement/repair of worn out/defective item with minimum down time after Defect Liability Period having HVAC System, 11/0.433KV Substation & DG Set, Lift, Fire alarm and Fire Fighting System IBMS System, Solar Panel/Solar Work, Sewage Treatment Plant, Water Supply etc as specified in the BOQ .

Bidder Name

Amount

tribeni Constructions ltd(GSTN-19AABCT8186C1Z4)

K S M BASHIR MOHAMMAD AND SONS(GSTN-09AAEFK3277F1Z9)

Globalzone Sanitory Infrastructure Pvt. Ltd.(GSTN-09AAGCG1652H1ZM)

N S Associates Pvt Ltd.(GSTN-07AABCN7057J1Z8)

KASANA BUILDERS PRIVATE LIMITED(GSTN-09AADCK2960P1ZZ)

RISHABH CONSTRUCTIONS PVT. LTD.(GSTN-08AABCR0445E1ZR)

G S Express Pvt Ltd(GSTN-09AACCG5655J2Z9)

GARG BUILDERS(GSTN-07AAPFG3406P2ZX)

SOM PROJECTS PVT LTD(GSTN-09AAJCS9451K1ZN)

Anurag Enterprises(GSTN-09AABFA6634R1ZY)

ASIAN CONSTRUCTION COMPANY(GSTN-NA)

C K Infrastructures Limited(GSTN-NA)

MUNDESHWARI CONSTRUCTION(GSTN-NA)

Bidder Name

Amount

tribeni Constructions ltd(GSTN-19AABCT8186C1Z4)

K S M BASHIR MOHAMMAD AND SONS(GSTN-09AAEFK3277F1Z9)

Globalzone Sanitory Infrastructure Pvt. Ltd.(GSTN-09AAGCG1652H1ZM)

N S Associates Pvt Ltd.(GSTN-07AABCN7057J1Z8)

KASANA BUILDERS PRIVATE LIMITED(GSTN-09AADCK2960P1ZZ)

RISHABH CONSTRUCTIONS PVT. LTD.(GSTN-08AABCR0445E1ZR)

G S Express Pvt Ltd(GSTN-09AACCG5655J2Z9)

GARG BUILDERS(GSTN-07AAPFG3406P2ZX)

SOM PROJECTS PVT LTD(GSTN-09AAJCS9451K1ZN)

Anurag Enterprises(GSTN-09AABFA6634R1ZY)

ASIAN CONSTRUCTION COMPANY(GSTN-NA)

C K Infrastructures Limited(GSTN-NA)

MUNDESHWARI CONSTRUCTION(GSTN-NA)

Bidder Name

Amount

tribeni Constructions ltd(GSTN-19AABCT8186C1Z4)

K S M BASHIR MOHAMMAD AND SONS(GSTN-09AAEFK3277F1Z9)

Globalzone Sanitory Infrastructure Pvt. Ltd.(GSTN-09AAGCG1652H1ZM)

N S Associates Pvt Ltd.(GSTN-07AABCN7057J1Z8)

KASANA BUILDERS PRIVATE LIMITED(GSTN-09AADCK2960P1ZZ)

RISHABH CONSTRUCTIONS PVT. LTD.(GSTN-08AABCR0445E1ZR)

G S Express Pvt Ltd(GSTN-09AACCG5655J2Z9)

GARG BUILDERS(GSTN-07AAPFG3406P2ZX)

SOM PROJECTS PVT LTD(GSTN-09AAJCS9451K1ZN)

Anurag Enterprises(GSTN-09AABFA6634R1ZY)

ASIAN CONSTRUCTION COMPANY(GSTN-NA)

C K Infrastructures Limited(GSTN-NA)

MUNDESHWARI CONSTRUCTION(GSTN-NA)

MUNDESHWARI CONSTRUCTION

KASANA BUILDERS PRIVATE LIMITED

K S M BASHIR MOHAMMAD AND SONS

G S Express Pvt Ltd

GARG BUILDERS

tribeni Constructions ltd

C K Infrastructures Limited

ASIAN CONSTRUCTION COMPANY

Anurag Enterprises

Globalzone Sanitory Infrastructure Pvt. Ltd.

RISHABH CONSTRUCTIONS PVT. LTD.

SOM PROJECTS PVT LTD

MUNDESHWARI CONSTRUCTION

K S M BASHIR MOHAMMAD AND SONS

GARG BUILDERS

tribeni Constructions ltd

C K Infrastructures Limited

Anurag Enterprises

KASANA BUILDERS PRIVATE LIMITED

G S Express Pvt Ltd

SOM PROJECTS PVT LTD

RISHABH CONSTRUCTIONS PVT. LTD.

Globalzone Sanitory Infrastructure Pvt. Ltd.

ASIAN CONSTRUCTION COMPANY

K S M BASHIR MOHAMMAD AND SONS

tribeni Constructions ltd

MUNDESHWARI CONSTRUCTION

C K Infrastructures Limited

GARG BUILDERS

KASANA BUILDERS PRIVATE LIMITED

Anurag Enterprises

G S Express Pvt Ltd

SOM PROJECTS PVT LTD

Globalzone Sanitory Infrastructure Pvt. Ltd.

RISHABH CONSTRUCTIONS PVT. LTD.

ASIAN CONSTRUCTION COMPANY

MUNDESHWARI CONSTRUCTION

RISHABH CONSTRUCTIONS PVT. LTD.

K S M BASHIR MOHAMMAD AND SONS

Anurag Enterprises

tribeni Constructions ltd

C K Infrastructures Limited

G S Express Pvt Ltd

KASANA BUILDERS PRIVATE LIMITED

SOM PROJECTS PVT LTD

Globalzone Sanitory Infrastructure Pvt. Ltd.

ASIAN CONSTRUCTION COMPANY

N S Associates Pvt Ltd.

MUNDESHWARI CONSTRUCTION

KASANA BUILDERS PRIVATE LIMITED

G S Express Pvt Ltd

GARG BUILDERS

tribeni Constructions ltd

Anurag Enterprises

C K Infrastructures Limited

Globalzone Sanitory Infrastructure Pvt. Ltd.

ASIAN CONSTRUCTION COMPANY

RISHABH CONSTRUCTIONS PVT. LTD.

SOM PROJECTS PVT LTD

N S Associates Pvt Ltd.

K S M BASHIR MOHAMMAD AND SONS

KASANA BUILDERS PRIVATE LIMITED

G S Express Pvt Ltd

tribeni Constructions ltd

Anurag Enterprises

C K Infrastructures Limited

GARG BUILDERS

Globalzone Sanitory Infrastructure Pvt. Ltd.

ASIAN CONSTRUCTION COMPANY

RISHABH CONSTRUCTIONS PVT. LTD.

SOM PROJECTS PVT LTD

N S Associates Pvt Ltd.