Up-gradation of Duhak to Garthoon road km 0/0 to 4/500

Amount

Excavation in hilly area in all heights and depths and in all kind of soil by all means including saturated soil comprising of ordinary soil, ordinary rock, soft rocks, hard rocks, chiseling/ wedging out rock ( where blasting is prohibited) and their intermediate classification of soil complete including setting out true to the required line, grades, width cutting and trimming of side slopes and level as shown in the drawing and as directed by the Engineer-in- Charge at site according to the M.O.R.D. technical specification section 300 and 1600 and sorting out useful materials and stacking the same with in all leads and lifts in acquired width of the road and transportation of useful material for filling in road ways, camber, embankments for grade improvements and disposal of all surplus material to the approved dumping sites through all modes of transportation including head load or animals transport or mechanical means along with its leveling fine dressing and carriage of machineries, materials, tools equipments and safety measures and other incidentals, necessary to complete the work by Mechanical means / labour if required. All useful materials such as stones shingle, aggregate and slates etcetera shall be sorted and stacked in proper stack. Recovery for useful stones of 131.15 cubic meter at the rate Rs. 300/- ( Rupees Three Hundred) only per cubic metre shall be effected from the contractor's bill on pro-rata basis as per actual quality executed. Any loss to the public / private property during the course of execution shall be the absolute responsibility of the contractor which shall have to be compensated by him in all cases. The rate is inclusive of octroi, royality, Malkana, toll tax, sale tax ,GST or other taxes imposed by the Government.

Loosening of the ground upto a level of 300 mm (Three hundred millimetre) below the sub grade level, watered, graded with motor grader and compacted in layers to meet requirement of Tables 300.1 and 300.2 with three wheel 80-100 (eighty to hundred) Kn static roller for sub grade construction as per M.O.R.D. Technical Specification section 300 and entire satisfaction and direction of Engineer - in- Charge including carriage of material with in all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Earth work in excavation for structures in all depths in all kinds of soil as per drawing and M.O.R.D. technical specification clause 305 & 1603 including setting out, construction of shoring and bracing, removal of stumps and other deleterious materials and disposal in all lead and lift including dressing of sides and bottom and back filling in trenches with excavated suitable materials. All work of rock cutting by blasting shall be carried out by taking all necessary precautions against soil erosion, damage to hill side, water pollution etc. and to protect stability of hill side, rock shall be excavated with chiseling and wedging out rock (where blasting is prohibited). All earth work in cutting/excavation including rock excavation shall be carried out true to lines grades, side slopes, width, camber super elevation and level as shown on the drawings as directed by the Engineer-in-Charge hauling and stacking of materials useful for construction at suitable sites and safe disposal of unsuitable cut materials in specified manner, filling of unevenness and finishing the road to specified dimension as directed by the Engineer-in-Charge. If the foundation of the structure is in an area with stagnant water or water is met with in the excavation due to spring seepage rain and other causes it shall be removed by suitable diversion, bailing out or pumping as directed and the area of the foundation or embankment shall be kept dry. Any loss to the public or private property during the course of excavation shall be the whole responsibility of the contractor which shall have to be duly compensated by him at his own cost in all cases. The rate is including octroi, royality, Malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Back filling with granular material behind abutment, wing wall, return wall retaining walls complete as per drawing & MORD technical specification clause 1203 and 1604 as per direction of the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental. The rate is including of octroi, royality, Malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Construction of granular sub-base by providing well graded material as per Table 400.1, spreading in uniform layers with Tractor mount grader on prepared surface, mixing by mix in place method with rotavator at OMC and compacting with three wheel 80-100 (eighty to hundred) KN static roller, to achieve the desired density, complete as per M.O.R.D. Technical specifications clause 401 for grading -I materials including carriage of material with in all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing laying spreading and compacting by mechanical means of stone aggregate size 63mm to 45mm ( sixty three millimetre to forty five millimetre) Grading-II[75mm( seventy five millimetre) consolidated thickness to water bound Macadam specification including spreading in uniform thickness using template, hand packing, rolling with three wheel 80-100 (eighty to hundred) K.N. static roller in stages to proper grade and camber including applying and brooming, stone screening type-B of size 11.2mm (Eleven point two millimetre) nominal size at the rate of 0.20 cum (zero point two zero cubic metre) per ten square metre and binding material at the rate of 0.06 cum (Zero point zero six cubic metre) per ten square metre to fill up the interstices of coarse aggregate, watering and compacting to the required density as per M.O.R.D. technical specifications clause 405 and as per the entire satisfaction and direction of Engineer - in- Charge including carriage of material with in all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing, laying, spreading and compacting by mechanical means stone aggregate size 53mm to 22.4mm ( fifty three millimetre to twenty two point four millimetre) Grading-III 75mm( seventy five millimetres) consolidated thickness to water bound Macadam specification including spreading in uniform thickness using template, hand packing, rolling with three wheel 80-100 (eighty to hundred) K.N. static roller in stages to proper grade and camber including applying and brooming, stone screening type-B of size at 11.2mm (Eleven point two millimetre) nominal size at the rate of 0.18 cum (zero point one eight cubic metre) per ten square metre to fill up the interstices of coarse aggregate, watering and compacting to the required density as per M.O.R.D. technical specifications clause No. 405 and as per entire satisfaction and directions of Engineer - in- Charge including carriage of materials within all leads and lifts and other incidental . The rate is including octroi, royality, Malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and applying primer coat on the prepared surface of granular base including cleaning of road surface with Hydraulic brooms and spraying primer at the rate of 0.85 kg/sqm (zero decimal eight five kilogram per square meter) using one part of bitumen emulsion SS-I and two parts of water mixed with Nano technology Tera prime emulsion @ 1% (One percent) of weight of emulsion by mechanical means as per M.O.R.D Technical Specification clause 502. as per directions of Engineer-in-charge including carriage of material within all leads lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and applying tack coat on the prepared of granular surface treated with primer and cleaned with Hydraulic brooms and spraying tack coat at the rate of 0.275 kg/sqm (zero decimal two seven five kilogram per square metre) using one part of bitumen emulsion RS-I and two parts of water mixed with Nano technology tack emulsion @ 1.4% (One decimal four percent) weight of emulsion as per Technical Specification clause 503 and as per directions of Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and applying tack coat on the prepared bituminous surface treated with primer and cleaned with Hydraulic brooms and spraying tack coat at the rate of 0.225 kg/sqm (zero decimal two two five kilogram per square metre) using one part of bitumen emulsion RS-I and two parts of water mixed with Nano technology tack emulsion @ 1.4% (One decimal four percent) weight of emulsion as per Technical Specification clause 503 and as per directions of Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and laying bituminous macadam with hot mix plant using crushed stone aggregates of grading as per Table 500.4 premixed with bituminous binder at the rate of 3.30% (three point three zero percent) of mix and Nano technology zycothorm @ 0.1% ( zero point one percent ) of weight of bitumen and transporated to site of work and laid over previously prepared surface with paver finisher to the required grade, level and alignment and rolled to achieve the desired compaction as per MORD Technical Specification Clause 504. including hauling of materials in all lead lifts and as per the directions of Engineer - in- Charge including carriage of materials within all leads , lifts and other incidental . The rate is including octroi, royality, Malkana, toll tax, sale tax, GST or other taxes imposed by the Government

Providing and laying 30mm (thirty millimetres) campacted thickness bituminous concrete with minimum 100-120 (one hundred to one hundred twenty) TPH hot mix batch type plant with electronic control grading-II using crushed aggregate 13.2mm (thirteen decimal two millimetres) nominal size of specified grading premixed with bituminous binder V-G-10 (viscosity grade-ten) at the rate of 5.40 to 5.60 (five decimal four zero to five decimal six zero) percent of mix and filler or as per design mix with nano technology zycotharm @ 0.1% (zero decimal one percent) of weight bitumen transported to site, laid with censor paver finisher hydraulic with sensor control to the required grade level and alignment over a previously prepared surface and rolling complete with smooth three wheel rollor 8-10 (eight to ten) tonne capacity for initial break down rolling and vibratory roller 8-10 (eight to ten) tonne capacity or pneumatic tyre roller of 12-15 (twelve- fifteen) tonne with tyre pressure of at least 0.56 MPa (zero decimal five six) for inter mediate rolling and finish rolling with 6-8 (six to eight) tonne smooth wheeled tandom rollers to achieve the desire compaction as per MORTH technical specification clause 507 including hauling of materials in all leads ,lifts and as per the directions and entire satisfaction of Engineer - in- Charge including carriage of materials within all leads, lifts and other incidental . The rate is including octroi, royality, Malkana, toll tax, sale tax, GST or other taxes imposed by the Government

Scarifying the existing bituminous road surface to a depth of 150 mm (one hundred fifty millimetres) and disposal of scarified material within all leads and lifts as per MORD Technical Specification Clause 301.4 or as per directions of Engineer - in- Charge including carriage of materials within all leads and lifts and other incidental . The rate is including octroi, royality, Malkana, toll tax, sale tax, GST or other taxes imposed by the Government

Construction of un-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement thickness as per design, over a prepared sub base with 43(forty three) grade cement or any type as per clause 1501 M-30 (M-thirty) grade, design mix cement concrete, coarse and fine aggregates conforming to IS:383(three hundred eighty three), maximum size of coarse aggregate not exceeding 25mm(twenty five millimetre ) mixed in a concrete mixer of not less than 0.2 (zero point two) cubic meter capacity and appropriate weight batcher using approved mix design, laid in approved fixed side form work ( steel channel), laying and fixing of 125(one hundred twenty five) micron thick polythene film, wedges, steel plates including levelling the form work as per drawing spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying deboning strips, primer, sealant, dowel bars, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14 days using curing compound (where specified) and water, finishing to line and grade as per drawing and as per M.O.R.D. technical specification clause 1501 and as per directions of Engineer - in- Charge including hauling /carriage of materials to various location through all modes of transportation with in all leads, lifts and other incidental The rate is including octroi, royality, Malkana, toll tax, sale tax, GST or other taxes imposed by the Government

Construction of sub grade and earthen shoulders with approved material obtain from borrow pits including transporting to site, spreading, grading to require slope and compacted to meet requirement of table 300.2 as per M.O.R.D. technical specification clause 407 and as per directions of Engineer - in- Charge including hauling /carriage of materials to various location through all modes of transportation with in all leads, lifts and other incidental The rate is including octroi, royality, Malkana, toll tax, sale tax, GST or other taxes imposed by the Government

Providing and laying of hot applied thermoplastic compound 2.5 mm (two point five millimetres) thick including reflectorising glass beads @ 250 gms (two hundred fifty grams) per square area, thickness of 2.5 mm (two point five millimetres) is excludive of surface applied glass beads as per IRC:35. The finished surface to be level, uniform and free from streaks and holes as per MORTH Technical specification clause 803 and as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental. The rate includes octroi,royality,Malkana,Tol tax, sale tax, GST or any other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated cement concrete 1:4:8 (one cement isto four sand isto eight graded stone aggregate 40mm (forty millimetre) nominal size) for plain/reinforced concrete in or under water water and curing complete for 14 (fourteen) days, in open foundations for all type of structures like retaining walls, breast walls and the like etcetera including pumping or bailing out water (surface and sub soil water) dewatering for all heights and depths and any quantum of water including removal of slush which may arise at the time of laying under water complete for all heights / depths including the cost of form work as per drawing and technical specification clauses 802, 803, 1202 and 1203 as per the directions of Engineer-In-Charge including carriage of materials within all leads, lifts and other incidental. The rate including the octroi, royality, Malkana, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing and laying 100 mm (One hundred millimetre) diametre PVC pipe weep holes in brick masonry/ stone masonry, plain/reinforced concrete abutment, wing walls, return walls and breast /retaining walls extending through the full width of the structures with slope of 1 (one) vertical: 20 (twenty) horizontal towards drawing face complete as per drawing and MORD technical specifications clause/section 709 and 1200 and as per direction of Engineer - in- Charge including carriage of materials within all leads, lifts and other incidentals . The rate is including of octroi, royality, Malkana, tolltax, sale tax, GST or other taxes imposed by the government.

Providing and laying mechanically mixed and vibrated concrete for plain concrete in open foundation for all types of structure complete of plain cement concrete grade M-10 ( M ten) nominal mix 1:3:6 (one cement : three sand : six graded crushed / broken stone aggregate 20mm (twenty millimetre) nominal size in or under water including curing complete pumping or bailing out water , dewatering removal of slush as required at site which may arise at the time of laying under water complete for all heights/ depths including the cost of form work as per drawings and technical specification section 800, 900 and 1200 as per the direction of Engineer-in-Charge Including carriage of material within all leads ,lifts and other incidentals. The rate including octroi, royality, Malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated concrete for plain cement concrete in sub structure for all type of structure complete grade M-15 ( M fifteen) design mix with cement contents not less than 275 kg (two hundred seventy five kilogram) per cubic metre in or under water including curing complete including pumping or bailing out water , dewatering removal of slush as required at site which may arise at the time of laying under water complete for all heights/ depths including the cost of form work in abutments etc. as per drawings and M.O.R.D. technical specification section 800, 900 and 1200, and as per the direction of Engineer-in-Charge including carriage of material within all leads , lifts and other incidentals .The rate including of octroi, royality, Malkana, tolltax, Sale Tax, GST or other taxes imposed by the government.

Providing and laying flooring laid over cement concrete bedding complete using cement concrete block grade M-15 ( M fifteen) design mix with cement contents not less than 275 kg (two hundred seventy five kilogram) per cubic metre in or under water including curing complete including pumping or bailing out water , dewatering removal of slush as required at site which may arise at the time of laying under water complete for all heights/ depths including the cost of form work in flooring laid over bedding as per drawings and M.O.R.D. technical specification clause 1303 and curing complete including hauling /carriage of materials to various location through all modes of transportation in all leads, lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax, sale tax, GST or other taxes imposed by the Government

Providing and laying mechanically mixed and vibrated concrete for plain cement concrete in cradle bedding for hume pipe of plain cement concrete grade M-15 ( M fifteen) nominal mix 1:2.5:5 (one cement isto two point five isto five) graded crushed stone aggregate 40mm (forty millimetres) nominal size on ground or under water and curing complete including pumping or bailing out water , dewatering removal of slush as required at site which may arrise at the time of laying under water complete for all heights/ depths including the cost of form work as per drawings and M.O.R.D. technical specification section 800,900 and 1101 including carriage of materials to various location through all modes of transportation in all leads, lifts and other incidental The rate is including octroi, royality, Malkana, toll tax, sale tax, GST or other taxes imposed by the Government

Filling in foundation trenches as per drawing & MORD technical specification clause 305.3.9 earth filling and as per direction of the Engineer-in-Charge including carriage of materials within all leads , lifts and other incidental. The rate is including of octroi, royality, Malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and laying ( to level or slope) 900mm dia (nine hundred millimetre ) diameter reinforced cement concrete heavy duty non pressure pipes IS Class NP-3 for culverts on first class bedding of granular materials in single row including fixing collar with cement mortar 1 : 2 ( One cement : two sand) but excluding the cost of excavation, protection works, back filling, concrete and masonry work in head walls and parapets as per drawing and M.O.R.D. technical specifications clause 1101 and as per direction of Engineer - in- Charge including carriage of materials to various location through all modes of transportation in all leads, lifts and other incidental. The rate is including of octroi, royality, Malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and laying of boulder apron laid in wire crates with 4 mm (four millimetres) diameter GI wire conforming to IS:280 and IS:4826 in 100 mm x 100 mm (one hundred into one hundred millimetres) mesh (woven diagonally) including 10 per cent extra for laps and joints laid with stone boulders weighing not less than 40 kg (forty killogramm) each as per drawing and MORD technical specification clause 1301 and as per direction and entire satisfaction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax, sales tax, GST or other taxes imposed by the Government

Providing and erecting "W" metal beam crash barrier comprising of 3 mm (Three millimetres) thick corrugated sheet metal beam rail, 70 cm (seventy centimetres) above road/ ground level, fixed on ISMC series channel vertical post, 150 x 75 x 5 mm (One hundred fifty into seventy five into five millimetres) spaced 2 m (two metres) centre to centre, 1.8 m (one decimal eight metres) high, 1.1 m (one decimal one metres) below ground/road level , all steel parts and fitments to be galvanized by hot dip process, all fittings to conform to IS:1367 and IS:1364, metal beam rail to be fixed on the vertical post with a spacer of channel section 150 x 75 x 5 mm, (One hundred fifty into seventy five into five millimetres) 330mm (three hundred thirty millimetres) long complete as per MORTH technical specification clause 810. and as per direction of Engineer - in- Charge including carriage of materials within all leads ,lifts and other incidentals . The rate is including of octroi, royality, Malkana, tolltax, sale tax, GST or other taxes imposed by the government.

Supplying fitting and placing HYSD bar reinforcement in sub-structures complete as per drawings and MORD technical specifications section 1000 and 1200, including cutting bending, binding, Straightening and placing in position complete in all respect including the cost of binding, wire upto all heights and depths and as per direction and entire satisfaction of Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate is including Royality, Malkhana, Octroi, toll tax, sales tax, GST or any other taxes imposed by the Government.

Supplying fitting and placing HYSD bar reinforcement in super structures complete as per drawings and MORD technical specifications section 1000 and 1400, including cutting bending, binding and placing in position complete in all respect including the cost of binding wire upto all heights / depths as per the direction and entire satisfaction of Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate is including Royality, Malkhana, Octroi, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated concrete for reinforced concrete in substructure using reinforced concrete grade M-20 ( M twenty ) design mix with cement contents not less than 330 kg (three hundred thirty kilogramm) per cubic metre with 20mm (twenty millimetre) nominal size graded crushed stone aggregate as per drawing and M.O.R.D. technical specification section 800,900 and 1200 Including the cost of form work but excluding the cost of reinforcement for reinforced concrete work in bed block, dirt wall etcetra and as per the direction of Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals .The rate is including of octroi, royality, Malkana, tolltax, Sale Tax, GST or other taxes imposed by the government.

Providing and laying mechanically mixed and vibrated plain cement concrete in open foundation of all type of structure complete Grade M-20 (M-Twenty) design mix with minimum cement contents of 330 kgs (Three hundred thirty kilogramms) per cubic meter with 20 mm (Twenty millimetres) nominal size graded crushed/ broken stone aggregate and curing complete including the cost of form work complete for all heights / depths as per drawings and MORD technical specifications section 800,900 and 1200 and as per the direction of Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals .The rate is including of octroi, royality, Malkana, tolltax, Sale Tax, GST or other taxes imposed by the government.

Providing and laying mechanically mixed and vibrated reinforced cement concrete in super structure as per drawing and M.O.R.D.. technical specification section 800, 900 and 1400 using R.C.C. grade M-25 (M- twenty five) design mix with cement concrete not less than 400 kg (four hundred kilogramm) per cubic metre with 20mm (twenty millimetre ) nominal size graded crushed stone aggregate and curing complete including cost of form work but excluding the cost of reinforcement for reinforced concrete work in deck slab and to the entire satisfaction and as per the direction of Engineer-in-Charge including carriage of material within all leads , lifts and other incidentals .The rate is including of octroi, royality, Malkana, tolltax, Sale Tax, GST or other taxes imposed by the government.

Providing and fixing of typical PMGSY informatory sign board with logo as per drawing and M.O.R.D. technical specification section 1700. Three MS plates of 1.6 mm ( one point six millimetres) thick top and middle plate duly welded with MS flat iron 25mmx5mm ( twenty five millimetres into five millimetres) size on back on edges. The lower plate will be welded with MS angle iron frame of 25mmx25mmx5mm (twenty five millimetre into twenty five millimetre into five millimetre). The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 Nos. ( Two Nos.) 75mmx75mm (seventy five millimetre into seventy five millimetres) of 12 SWG (twelve standard wire gauge) sheet tubes posts duly embedded in cement concrete M-15 ( M fifteen) grade nominal mix 1:2.5:5 (one cement : two and half sand : five graded or crushed stone aggregate 40mm (forty millimetres) grade blocks of 450mmx450mmx600mm ( four hundred fifty millimetres into four hundred fifty millimetres into six hundred millimetres), 600mm ( six hundred millimetres) below ground level. The top most diamond plate will be welded to middle plate by 47mmx47mm ( forty seven millimetre into forty seven millimetres) of 12 SWG ( twelve standard wire gauge) steel plate tube. All MS will be stove enameled on both sides. Lettering and printing, arrows, borders etcetera will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing and M.O.R.D. technical specifications section 1700 including carriage of materials to various location through all modes of transportation in all leads, lifts and other incidental complete and as per direction of Engineer-In-Charge. The rate is including of octroi, royality, Malkana, tolltax, sale tax, GST or other taxes imposed by the government.

Reinforced cement concrete mechanically mixed and vibrated grade M-15 ( M- fifteen) nominal mix 1:2.5:5 (one cement : two and half sand : five graded crushed/ broken stone aggregate 40mm (forty millimetres) nominal size Kilometre stone of stranded design as per IRC:8 (eight) fixing in position including painting and printing etcetera as per drawing and MORD Technical specification rural roads clause 1703 (Ordinary Kilometre stone Precast) including hauling of materials in all leads, lifts and other incidental or as per direction and entire satisfaction of Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate is including Royality, Malkhana, Octroi, toll tax, sales tax, GST or any other taxes imposed by the Government.

Reinforced cement concrete mechanically mixed and vibrated grade M-15 ( M- fifteen) nominal mix 1:2.5:5 (one cement : two and half sand : five graded crushed/ broken stone aggregate 40mm (forty millimetres) nominal size Kilometre stone of stranded design as per IRC:8 (eight) fixing in position including painting and printing etcetra as per drawing and MORD Technical specification rural roads clause 1703, 200 mtrs( Two hundred metre stone precast) including hauling of materials in all leads, lifts and other incidental or as per direction and entire satisfaction of Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate is including Royality, Malkhana, Octroi, toll tax, sales tax, GST or any other taxes imposed by the Government.

Providing and fixing of semi reflective cautionary, mandatory and informatory sign board of 600 mm (six hundred millimetres) equilateral triangle board as per IRC:67 made of 1.5 mm (One decimal Five millimetre) thick MS sheet duly stove enameled white colour in front and gray colour on back with red reflective border of 65 mm (Sixty Five millimetre) width and required letters and figures with reflective tape engineering grade as per section 1700 of MORD for rural roads of required shade and colour supported and welded on 47mm x 47mm x12 SWG (Forty seven into forty seven millimetres of twelve standred wire gauge) sheet tube firmly fixed to the ground by mean of properly designed foundations with M-15 (M-fifteen) grade cement concrete 450 x450 x 600 mm, (Four Hundred Fifty into Four Hundred fifty into Six Hundred millimetre), 600 mm (six Hundred millimetre) below ground level as per drawing and MORD technical section 1700 including painting angle iron post with primer and two coats of epoxy paint as per specification and entire satisfaction / direction of Engineer-In-Charge. including carriage of materials to various location through all modes of transportation in all leads , lifts and other incidental. The rate is including of octroi, royality, Malkana, tolltax, sale tax, GST or other taxes imposed by the government.

Providing and fixing of Semi-reflective cautionary, mandatory and informatory sign 600mm (six hundred millimetre) Circular board as per IRC-67 made of 1.5 mm (one point five millimetre) thick MS-sheets duly stove enameled paint in white colour in front and gray colour on back with red reflective border of 65 mm (sixty five millimetre) width and required letters and figures with reflective tape engineering grade as per section 1700 of MORD for Rural Roads of required shade and colour supported and welded on 47mm x 47mm of12 SWG ( forty seven into forty seven millimetre of twelve Standard Wire Gauge) sheet square tube firmly fixed to the ground by mean of properly designed foundation with M-15 grade ( M-fifteen grade) cement concrete 450mm x 450 mm x 600 mm ( four hundred fifty into four hundred fifty into six hundred millimetre), 600 mm ( six hundred millimetre) below ground level as per drawings and Technical Specification section 1700 including painting angle iron post with primer and two coats of epoxy paint as per specification and entire satisfaction / direction of Engineer-In-Charge. including carriage of materials to various location through all modes of transportation in all leads , lifts and other incidental. The rate is including of octroi, royality, Malkana, toll tax, sale tax, GST or other taxes imposed by the government.

Providing and fixing Semi Reflective Traffic Signs Direction and place indentification signs boards upto 0.90 Sqm size of board as per IRC:67 made of 2mm (Two millimetre) thick M.S. Sheet duly stove enameled paint white colour in front and gray colour on back with reflective border of 70mm (Seventy millimetre) width and required message, letters, figures with reflective tape of engineering grade of required shade and colour. Supported and welded on 47mm x 47mm (Forty Seven into Forty seven millimetre) of 12 SWG Square tube of 3050 mm height duly strengthened by 25mm x 5 mm (Twenty five into five millimetre) M/S flat iron on edges on back firmly fixed to the ground by means of properly designed foundations with M-15 grade cement concrete 450 mm x 450mm x 600 mm (Four Hundred Fifty into Four Hundred fifty into Six Hundred millimetre), 600 mm (Six hundred millimetre) below ground level as per approved drawing and technical specification section 1700 including hauling/ carriage of materials to various location through all modes of transportation in all leads, lifts and other incidental complete and as per direction of Engineer-In-Charge. The rate is including of octroi, royality, Malkana, toll tax, sale tax, GST or other taxes imposed by the government.

Guard Stone on Curve made of Reinforced cement concrete/ local stone of standard design as per IRC:25, fixed in position including finishing and lettering but excluding painting as per drawing and technical specification Clause 1704 and as per the direction of Engineer-in-Charge Including carriage of material within all leads , lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax, sale tax, GST or other taxes imposed by the Government

Painting lines, dashes, arrows, etc. on roads in two coats on new work with ready mixed road marking paint conforming to IS:164 on bituminous/concrete surface, including cleaning the surface of all dirt, dust and other foreign matter, demarcation at site and traffic control as per drawing and technical specification clause 1702 and as per the direction of Engineer-in-Charge Including carriage of material within all leads , lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax, sale tax, GST or other taxes imposed by the Government