SPL REPAIR DAMAGED RCC JALI, BRICK WORK WALL PLASTER, PROVN OF FENCING 3 FT HIGH WITH Y ANGLE AND PROVN OF TIOLET BLOCK NEAR BLDG NO P-23 AT OUTRAM LINE UNDER GE (ARMY) BARODA

Amount

Surface dressing not exceeding 15cm deep in soft/loose soil complete all as specified and directed.

Surface excavation not exceeding 30 Cm deep and averaging 15 cm deep and getting out in soft / loose soil.

M & L Cement concrete in foundations, filling and mass-concrete type D2 1:4:8 (40 mm graded stone aggregate)

M & L for M-25 Grade design mix reinforced cement concrete in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc; basement slabs, under-reamed piles and mass concrete.

M & L for M-25 Grade design mix reinforced cement concrete in column, pier, pillars beams; plinth beams; bases for columns, etc; basement slabs, under-reamed piles and mass concrete.

M & L for M-25 Grade design mix reinforced cement concrete in lintel, lintel beams; plinth beams; bases for columns, etc; basement slabs, under-reamed piles and mass concrete.

M & L for M-25 Grade design mix reinforced cement concrete in slab supported on wall, shelves slab dick slab, bases for columns, etc; basement slabs, under-reamed piles and mass concrete.

Use and waste formwork for rough finished flat surface of concrete to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter.

Use and waste formwork for rough finished flat surface of concrete sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc..

Use and waste formwork for rough finished flat surface of concrete to sides of concrete to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping).

Use and waste Formwork for fair finished surface to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete.

M&L Brick work with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in cement Mortar 1:6.

M&L half thick Brick work with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in cement Mortar 1:4 as in partition wall

M&L 40 mm thick Damp proof course in cement concrete type Bo 1:2:4 to horizontal or vertical surfaces including necessary formwork using water proofing compound @ 3% by wt of cement.(WPC will be measured separately)

Applying evenly a coat of blown type bitumen at the rate of 1.50 kg per square metre and blinding with clean dry sand @ 0.05 cu. m. per sq. m

M & L for mild steel TMT bars 10mm dia and over, cut tolength, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

M & L for mild steel TMT bars but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

Spreading and leveling of soft/loose soil in floor in layers n exc. 25 cm thick including well ramming watering as required.

M&L Hardcore of broken stone of gauge n exc. 63 mm, deposited, spread and leveled in layers n exc. 15 cm thick, watered and rammed to a true sur-face

M&L cement concrete 75 mm thk, type D2 1:4:8 (40 mm graded stone aggregate) in sub base of flooring.

M&L 25 mm thick cement concrete in flooring type Bo, 1:2:4 (12.5mm graded stone aggregate)

M&L for non skid colour ceramic tile 7 to 8 mm thick area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc set and jointed inneat cement slurry and pointed in white or colour cement to match including screed bed or bedding layer of 15 mm thick, in CM 1:6.

M&L for Glazed ceramic coloured walls tiles in vertical surfaces 300x200x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm thick rendering on vertical surface of wall or concrete surfaces in CM 1:4 to receive wall tiles.

M&L 75 mm thick cement concrete type C2 1:3:6 using 40mm graded stone aggregate in plinth protection for finished even and smooth without using extra cement including forming joints and filling with bituminous filler material.

M&L Rendering in two layer on fair faces of brick work or concrete surfaces of wall 5 mm thick in CM 1:4 mixed with WPC @ 3% by wt of cement for finished even and smooth without using extra cement over 10 mm thick rendering in cement mortar 1:6 smooth without using extra cement (WPC will be measured separately)

Rendering 10 mm thick on fair faces of brick work or concrete surfaces of wall in cement mortar 1:6 for finished even and smooth (without using extra cement)

Rendering 5 mm thick on fair faces of ceiling in cement mortar 1:3 for finished even and smooth withou using extra cement

Supply only integral water proofing compound

S&F 15mm bore galvanised mild steel tubing medium grade with all fittings and fixed complete to walls and ceilings or laid in floors all as directed.

S&F 25mm bore galvanised mild steel tubing medium grade with all fittings and fixed complete to walls and ceilings or laid in floors all as directed.

S&F 500 Ltrs Rotational moulded polyethylene water storage tanks (cylin-drical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I

S&F Ball brass valves, for 20 mm bore of pipe high pressure, with polythene float and fly- nut complete, screwed for iron pipe or brass ferrule and fixed

S&F 15mm bore pillar taps fancy type, cast copper alloy with capstan heads, chromium plated, screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts screwed for iron pipe and fixed

S&F 15mm bore stop valve fancy type cast copper alloy, chromium plated, screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed

S&F 15mm bore stop valve fancy type cast copper alloy, chromium plated, long shunk concealed type screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed

S&F Vitreous China Squatting pan,"Orissa" pattern size 580x400 white with intergral foot rest complete including provision of lime concrete bedding (excluding flushing cistern and flush pipe).

S&F Vitreous China wash basin, white flat baack, size 550x400mm excluding taps, waste, chain and plug and porcelain stopper but including brackets.

S&F Vitreous China urinal half stall type white (excluding flushing cistrern, flush pipe and waste pipe).

M&L 32mm waste fittings, brass, chromium plated for glazed ware sinks, basins etc with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed.

S&F 32mm bore low density polyethylene (LDPE) pipes of pressure rating 6Kgf/sq.cm for basins and urinals

S&F 32mm bore brass chromium plated trap 'P' or 'S' pattern for wash basins and urinals with inlet and outlet, screwed for pipe or connections and with one cleaning cap and fixed

Supply and fix urinal spreader of PTMT any color for fixing with 15 mm dia pipe (Min weight 60 gms)

Supply and fix PVC connection 15 mm size with PTMT nuts of length 450 mm long.

S&F grating square 150 mm size of PTMT (Minimum weight 100 gms)

S&F 15mm bore bib tap, fancy type, cast copper alloy with crutch of butterfly handle, screwed down, high pressure for iron pipe or for brass ferrule

S & F for PVC low level flushing cistern, white, 10 Ltrs capacity complete with all internal accessories & fixed to wall & making good to wall surfaces incl. taking down existing flushing cistern complete.

S & F for Towel rail 600 mm long with PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats.

S & F brass CP hand jet sprey for bathing including bracket and PVC connection of required length.

S & F 125mm dia chromium plated shower rose with swivel joints including fixing to GI union complete

S&F 100mm bore sand cast iron soil, waste, vent pipes in any length with or without ears with cement joints, fixed to walls

S & F 100mm CI vent cowl

M & L for 150x100 mm dia salt glazed stoneware gully trap, square or round mounted, type "P" as specified.

S & F 75mm bore sand cast iron soil, waste, vent pipes in any length with or without ears with cement joints, laid in trenches or in floors

S & F 100mm bore branch pieces, single (equal or ;unequal) ordinary or inverted (spigot or socket type) or with parallel branches with access door all as directed

S & F 75mm bore cast iron bends diminishing pieces or tapers (large bore measured) with oval access doors

S & F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specification and drawing. The door frame shall be tied to the wall using 75/100mm long MS screw as directed .

S & F Factory made solid panel PVC door shutte 30mm thick (style) consisting of frame made out of MS tube for top and bottom rails. M S tube for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stile and rails with suitable PVC sheet beading and jointed together with solvent cement.

S&F Butt hinge, medium wight, cold rolled mild steel of 100 mm size

S&F 150 mm aluminium alloy handles, cast type anodised all as specified.

S&F150mm aluminium anodised barrel tower bolts of extruded section and fixed.

S&F of Powder coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

S&F 4.00mm thick figured glass, pin head type and glazing with oil putty in square n exec 0.5 sqm in each pane

M&L preparing new plastered surfaces of wall and applying three coats of white wash on wall

M&L preparing new plastered surfaces of ceiling and applying three coat of white wash .

M&L preparing new plastered surfaces of wall and applying two coats of cement base paint over a coat of primer.

M & L for 10 mm thick cement plaster (1:3) in CM with using water proofing compound @ 2% by weight of cement as per manufacturer's instructionsand 0.5% recrone fiber shall be applied on padding concrete when concrete is still green complete all as specified and directed by Engr-in-charge. (WPC will be measured separately).

M & L for applying evenly a priming/tack coat with bituminous primer at 10 kg per 10 sq metre (Paving bitumin).

M & L for APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified.

M & L for 16 to 18 mm thick machine cut green marbel stone as in floor, steps (in single piece), cooking platform etc laid over 15 mm thick cement screed and jointed with base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including cement mortar 1 : 6 complete all as specified and as directed.

M&L for cement concrete 100mm thick type B-2 1:2:4 (40mm graded stone aggregate) as in approach path laid in alternate pannels used waste of form work/screed and to dividing the area in panel, finished even and smooth all as directed by Engineer in charge.

M&L for machine pressed precast concrete (rubber moulded) coloured interlocking paver block any shape & size conforming to IS 15658-2006 of 60mm thickness, M-35 grade, bedded and jointed with gray cement and pigment over 30mm thick sand cushioning (sand cushion paid separately) complete all as specified and as directed.

M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and directed

M&L for PCC 1:2:4, Type B-0 using 12.50mm graded stone aggregate as in coping,benching,roof kerb including necessary formwork, weathering, slightly rounded or chamfered angles and throating complete all as specified and directed.

M&L for cement concrete bed to drain pipes in PCC 1:3:6, type C2 (using 40mm graded stone aggregate), for 150mm dia drain pipe including packing under and haunching against the sides of pipes with concrete after they are laid and tested complete all as specified and directed.

M&L for reinforced concrete pipe of 150mm bore of pipe, class NP-2, laid and jointed in cement mortar (1:1) complete with collars complete all as specified and directed.

M&L for PCC (1:2:4) type B-1 using 20 mm graded aggregate as in benching to surface channels for manholes or drains etc, including finishing top of benching even and smooth using extra cement and including necessary formwork, complete all as specified and directed.

M&L for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement including forms, moulds, mitred / stopped ends etc complete all as specified and directed.

M&L, rendering 10 mm thick fair faces of brick work or concrete suraces in CM 1:4 finished even and smooth without using extra cement complete all as specified and directed.

M&L for pre-cast reinforced cement concrete 1:2:4, type B1 (using 20mm graded stone aggregate) as in manhole cover with plain fair surface including chamfers, weatherings, throatings, necessary form work and set in CM (1:6), placed in position complete all as specified and directed.

Mild Steel TMT Bar 10mm dia and over mm dia as in reinforcement, cut to length, bent to shape required, including cranking bending and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

M/L for cutting into existing MH for connecting new sewer line of dia .150mm including making good to existing MHS and channels etc all as specified in SSR.

Demolition of stone slabs and tiles of any description or thickness in floors & wall, laid bedded & pointed in any mortar.

Demolition of cement concrete (unreinforced) in ground floor and paving n.exc 15 cm thickness (below or above ground level)

Demolition of cement concrete of any description and in any position not otherwise specifically provided for

Demolition brickwork or stone/boulder masonry built in cement mortar including all quoins, arches, pillars, etc,

M&L for Providing precast cement concrete louvres and jallies, 25mm thick (measured solid), including all mouldings set and jointed in CM 1:4 but excluding frame (Pre cast frame shall be measured separately and paid for under item

M&L Rendering in two layer on fair faces of brick work or concrete sur-faces of wall 5 mm thick in CM 1:4 mixed with WPC @ 2% by wt of cement for finished even and smooth without using extra cement over 10 mm thick rendering in cement mortar 1:6 (WPC will be measured and paid separately).

Supply only Internal water proofing compound all as specified and directed.

M & L for preparing old decorated surfaces of wall applying one coat of cement base paint on external wall

M & L for Glazed ceramic coloured tiles in vertical surface 350x 250x 7mm/ 450X 300X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match, complete including 10mm thick cement mortar in CM 1 : 4 complete all as specified and as directed.

M & L for 100 mm thick PCC 1:4:8 mix type D2 using 40mm graded crushed stone agg as in sub base as in floor.

M & L for Chequered cement concrete tiles 30cm x 30cm x 22-25mm thick, set, jointed and pointed in neat cement slurry in floors complete all as specified and directed (WPC will be measured and paid separately).

M & L Cement concrete type B1 1:2:4 (20 mm graded stone aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges.

Demolation of brickwork or stone/boulder or PCC block masonry, built in any mortar including all quoins, arches, pillars, etc

M & L for cement concrete 1:2:4: type B1, (using 20mm graded stone aggregate) as in plinth courses, string courses, copings etc, as directed.

M & L for preparation of newly plastered surface of walls and applying two coats of cement base paint all as specified and directed.

M & L for mild steel work confirming to Fe-290 Gde E-165 in angle iron posts & struts in fencing including cutting top to shape as directed, drilling holes, noteching for wire etc. and including flat iron filletes for securing wire mesh or fence etc. including all necessary bolting riviting etc complete all as specified and directed

S & F in repairs galvanised 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specified and directed

M & L for preparation of new steel Surfaces of any description, over 10cm in width or girth, and applying two coats of synthatic enamel paint over a coat of red oxide primer.

S & F erecting of 610 mm dia punched tape concertina coil fencing, stretches along with two lines for RBT (supporting wire of the same material as concertina coil) having standard specifications including coating of P x 2 compound (anti rust) and fixed over existing 'Y' shape angle iron brackets on compound wall with and including using necessary scaffolding along the length of wall, complete all as specified and directed. Note : Concertina coil shall be stretched on ground and then lifted for fixing by means of mechanical crane or manually and resting over the existing 'Y' shape angle iron brackets/pickets which are already fixed on compound wall. Rate quoted by the contractor shall be deemed to include for making entire arrangement of fixing of coil. length between cook house to mortuary building is 300RM

M&L for sand cushoning, to cable with river sand and punning to provide required cover for UG cables all as directed at site.(punned thickness shall be measured)

M&L brick protection cover to electric cable with class 'B' bricks laid dry and flat abutting each other with gap between adjascent not exceeding 10mm.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size: 10 sqmm 2 core

M&L for galvanized steel tubing light Grade of 25 mm dia protection of cable fixed to pole/walls or laid in floors, road crossing ducts with all necessary fittings and fittings and fixed with clamps, bolts, nuts and washers etc complete all as specified and directed.

M&L concealed point wiring complete with 1.5 Sqmm single core multistranded copper conductor PVC insulated and unsheathed FRLS cable 1100 volts grade drawn through and including non metallic rigid PVC conduit, medium grade minimum 20mm dia ISI marked and conduit accessories concealed in wall etc with sunken type pressed steel/welded MS terminal boxes made out of 1.2 mm MS sheet, 3mm thick laminated sheath top cover for mounting of fittings, switches, sockets outlets, regulators etc complete including provisining of 1.5 sqmm PVC insulated unsheathed FRLS cable 1100 volt grade with multi stranded copper conductor to common earth and connected to earth dolly for One light/fan/bell point controlled by one switch 6 Amp one way

S & F MCB DB SPN 04 way factory made IP 42 protection class metal double door with 200 Amp rating bus bar 240/430V for fixing of MCBs/Isolators/RCCBs etc completed. Make: C&S/Havells/HPL

S & F MCBs 240/415 Volts 10 KA finger proof terminal, bi-connect termination, label holder, 35 Sqmm terminal capacity, insulated sliding shutter, large two position dolly, ISI marked to be fixed on DB. Make: C&S/Havells/HPL (DB will be measured and paid separately under respective items of sch A):-

MCB SPN 6 to 40 Amps.

MCB SP 6 to 40 Amps

M&L switch piano flush type single pole, one way 6amp .

S&fix ceiling rose 65x17mm three terminals .

S& F lamp holder,PVC/Polycarbonate type and back plate suitable for batten fitting with 9watt LED bulb

Supply, Fixing, Testing and commissioning of 4' LED not less than 1X18W LED Batten with LED tube not less than 18 watt. Similar to Batten cat Part No.REGALBATTEN8UPTO1X22wSSBSWH and LED tube light cat part No.CRYSTAL1213T8DSTL18WLED865SGLASS of Make- Havells or equivalent in Make: Philips/Wipro/CG

S & F wall security light LED type not less than 20W . The Luminaire connecting with not less tha 0.5 sqmm 3 core flexible stranded copper conductor wire upto ceiling rose complete with GI pipe suitable bend 1.2 mtr long and fixing on wall/pole with clamp, nut & bolt complete all as directed and specified by Engr-In-Charge. Make- Havells, Model-ENDURACITYLITEPLATSL20W LED 757SASYBOPC or equivalent in Phillips/Wipro/CG.

M&L earthing complete with galvanized steel earth plate electrode 600mmX600mmX6mm buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below normal ground level, the earth electrode surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15cm on all side and connected to and including galvanized earth lead wire 4.0 mm dia upto 7.5 mtrs long by means of nuts and bolts, check nuts and washers of GI and connected to earhing test point and earth dolly all as shown in electrical plate No 3 of MES schedule Part-I, and testing on completion including necessary excavation and earth work in any type of soil, PCC(1:3:6) type C1 chamber, CI cover with cast iron frame, funnel with watering pipe 20mm dia medium grade, wire mesh and lugs, GI protection pipe15mm dia, light grade 7.5 mtr long for protection of earth lead upto test point etc all as specified and as directed.

Supply, fixing, testing & commissioning of exhaust fan 300 mm sweep 1400 RPM with minimum airflow/air delivery 1710 Cmh, totally enclosed heavy duty motor, die cast aluminium rotor mounted on double ball bearing, IP-55, polarity-4, 230 Volt AC supply (single phase), rated power input not more that 90watt, with louvers and connecting up including provison of PVC insulated overall PVC sheathed copper conductor cable from ceiling rose to fan. Make : CG/Bajaj/Havells or equivalent. Similar to Crompton Greaves model No EXHD300-4-1

Excavation in trenches/post holes in soft/loose soil not exceeding 1.5 mtr wide and not exceeding 1.5 meter in depth for laying of cable and for poles/stay and struts not exceeding 10 Sqm on plan and getting out, excavated earth, forming bottom surfaces to required level complete all as specified and directed .

Removing excavated material (soil) not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed

Removing excavation material exc 250m but n.exc 500 m and depositing where directred.

Returning filling in including spreading leveling watering and well ramming in layers n.exc 25cm thick in soft/loose soil complete all as specified.

Supply and laying in trenches of GI steel tubing medium grade including all fittings such as Tees, elbow, bends etc for 25 mm bore of pipe complete all as specified.

Supply and laying in trenches/wall/roof of GI steel tubing medium grade including all fittings such as Tees, elbow, bends etc for 20 mm bore of pipe complete all as specified and directed .

S&F 25 mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe.

S&F 20 mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe.

M&L for cutting existing steel tubing for alterations or additions (Each cut measured) and inserting new Tee, bend, elbow etc up to 40 to 50 mm dia

M&L brick masonary valve pit of size 750mm X 750mm X 750mm (internal dimension) complete with MS angle iron frame work (Angle Iron size 40mm X 40mm X 6mm) & 3mm MS sheet top cover openable through hinges including necessary locking arrangement, rendering complete and painting with two coat of black bituminous paint over a one coat red oxide primer

RAJENDRASINH B THAKOR

Gayatri Associates