Special Repair for Strengthening of Link Road from Old Jagadhari road (Km 0.00 to 1.530) in Ambala District (Road ID 218) (Pdg. Decorative Poles with LED Fittings).

Amount

Wire 1.5 Sqmm ISI marked, FRLS PVC insulated, single core copper conductor cable. EL003

10 Sqmm ISI marked, FRLS PVC insulated, single core copper conductor cable. EL007

MCCB ,DISTRIBUTION BOARDS, MCB's, RCCB's, CHANGE OVER etc. Supply and erection of Modular case circuit breaker single pole/4 pole on existing wall/pedestal/Panel including bounding to earth and making necessary connections required to complete the job in all respect up to the entire satisfaction of the Engineer-in-charge of the work. 4 pole MCCB 6 amp to 100 amp HSR No. 23.22.1.9

MCCB Enclosure made of Sheet Steel suitable for mounting MCCB of following ratings MCCB up to 125 A FP HSR No. 23.22.2.1

Supply and erection of double door sheet steel enclosure distribution board suitable for MCBS and ELCBS etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect up to to the entire satisfaction of the Engineer-in-Charge of the work. TPN DB Horizontal type Double Door 4 way ( 8 incoming and 3phase*4 outgoing) HSR No. 23.22.4.5

Supply and erection of miniature circuit Breaker/isolator 240/415 V in the existing distribution board including making necessary connections:- 6 amp. to 32 amp Single Pole HSR No. 23.22.5.1

6 amp. to 32 amp MCB's TRIPLE POLE HSR No. 23.22.5.5

Supply and election of Goodridge Almirante type M.S. pedestal made of 50 mm *50 mm * 6 mm angle Iron frame with 3.00 mm thick M.S. sheet covering including shutters with suitable hinges and looking arrangement with the Godrich type handle including round bars. The to covering should have a downward overhang of 75 mm on all sides of pedestal, having two sets of water proof ventilation holes of suitable size on the sides, at top and bottom, each set containing four No’s. holes to discharge the heat produced by suitable size to make it water proof . The pedestal duly painted both inside and outside with two coats of approved paint and primary coat and its legs are embedded upto the entire depth in 1:2:4 cement concrete block, projected 75 mm all around the pedestal and 200 mm above the ground level including the cost of all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-in charge of the work. M.S. pedestal of size 750 mm wide, 900 mm high, 300 mm deep and bottom totally open , duly embedded in cement concrete block of size 900 mm*450 mm*200 mm above ground level , having a base of size 1050 mm* 600 mm* 250 mm below ground level. HSR No. 23.27.2

CHAPTER 24.0 - CABLE LAYING AND STREET LIGHTING EARTHING AND LIGHTENING ARRESTOR Earthing with GI earth pipe 4.5 m long and 40 mm dia with masonry enclosures on the top etc. (but without charcoal or coke and salt) as required. HSR No. 24.1.1

Extra for using salt and char coal/coke for pipe earth electrode as required. HSR No. 24.1.2

Providing and laying earth connections from earth electrode with 4.00 mm dia G.I. wire in 15 mm dia G.I. pipe from earth electrode as required. HSR No. 24.1.11

Providing and fixing 4.00 mm dia G1. Wire on surface or in recess for loop carthing as required. HSR No. 24.1.13

Laying of underground cable in pipe /existing open/closed tench tc as required:- 16 Sq mm to 35 sqmm 2 to 4 Core HSR No. 24.2.4.2

Supply and erection of copper lugs including crimping etc. entire satisfaction of Engineer-in- Charge of the work. 1.5 sqmm HSR No. 24.2.6.1

10 sqmm HSR No. 24.2.6.5

Supply and erection of suitable compression type brass cable glands for underground Cable :- 10 sqmm to 16 sqmm Cable 2 to 4 Core HSR No. 24.2.7.2

25 sqmm to 50 sqmm Cable 2 to 4 Core HSR No. 24.2.7.3

Supply and erection of aluminium lugs heavy duty including crimping etc. upto the entire satisfaction of the Engineer-in-charge of the work. 16 sqmm HSR No. 24.2.8.4

35 sqmm HSR No. 24.2.8.6

S/E mark double walled corrugated (DWC) HDPE, pipe 10 Kg/Cm2 ,laid 0.75 Mtr below ground level including diging and refilling of earth including cost of suitable size socket/cuppler for HDPE pipe including the cost of labour and material required to complete the job in all respect up to the entire satisfaction of Engineer in charge of the work. DWC/HDPE pipe 63/50 mm outer dia/inner dia HSR No. 24.5.2.3

RCC FOUNDATIONS FOR OCTAGONAL POLES Providing RCC foundation of M25 grade (1 Cement:1 Stone aggregate: 2 Coarse sand) i/c excavation, steel reinforcement (Fe 500) @ 70 kg/cum of concrete contents, concrete cover 50mm, anchor bolts etc. over a bed of PCC 1:5:10 of required dimensions for octagonal poles of various heights as per following specifications complete in all respects and as per directions of Engineer-in-charge 5m high pole HSR No. 24.8.3

Digging & refilling of trench 30 cm wide below ground level for erection of pipe/cable (up depth of 1 Mtr. Underground cable excluding the cost of cable/pipe complete in all respect. HSR No. 24.10.1

S/Eof under ground cable ,loose in existing pipe or trenches complete with necessary connections . Supply & Erection of 16 Sq. mm 4 Core Cable Armoured under ground cable ,loose in existing pipe or trenches, make Grandlay complete with necessary connections complete in all respect including all material required to complete the job in all respect & up to the entire satisfaction of the Engineer in charge of the work. Make Havells/Plaza/Grandlay. NS-1

Supply & Erection of 35 Sq. mm 3.5 Core Cable Armoured under ground cable ,loose in existing pipe or trenches, make Grandlay complete with necessary connections complete in all respect including all material required to complete the job in all respect & up to the entire satisfaction of the Engineer in charge of the work. Make Havells/Plaza/Grandlay. NS-2

SITC of Aesthetically designed decorative hot dipped galvanised mild steel step pole. Compatible for all Havells post top range. Hot dipped galvanized mild steel step pole. Elliptical Aluminum sheet with HAVELLS in grey color is riveted to the pole. Standard height of 4 mtr. Grey UV stabilized Polyurethane paint after hot dipped galvanizing. Upper section of pole with length 250mm and dia 48mm suitable for bracket mounting wall Thickness 2.9 to 3.2 mm, middle section of pole with length 2800 ±15 mm having Ø60mm, Wall Thickness 2.9 to 3.2 mm and having 2 Pressure die cast aluminium embellishment in golden yellow color for decoration. Bottom section with Dia of 114mm and length of 1200mm with Pole window of 300 mm at the height of 600mm from ground for terminal connections & mounting accessories containing 3mm thick Bakelite sheet having machine cut. Tringle head locking arrangement required on pole window. Elliptical Aluminum sheet with HAVELLS in grey color is riveted to the pole. Window cover is fitted with allen screws to the pole. Mounting base of the pole is Mild steel base plate of 250 X 250 mm with 4 no. circular holes at corner of base plate with dia of 20mm on 200 mm PCD suitable for M12 bolts. Base plate thickness is 10mm.The Decorative pole to be approved by Engineer in Charge & Architect with all labour and material required to complete the job in all respect up to the entire satisfaction of Engineer-in-Charge of work. Make. As per approved make list. NS-3

SITC of 72 Watt IP 66 , IK07 Led hanging decorative Street light in round shape suitauble for U shaped Brackets with viewing angle of 120 degree for better uniformity , with injection moulded clear Polycarbonate Cover , pressure diecast heat sink , with individual PC lens for better uniformity , built in potted electronic driver with THD<10%, built in surge protection upto 10 KV and other safety test as per IS 15885 part-2/sec13, operating voltage 140-270 V , Life of Led 50000 burning hrs , operating temperature of 50 degree celsius.The fixture should have system efficacy of minimum 110 Lumens /watt. The CCT of the Fixture Warm white with all labour and material required to complete the job in all respect up to the entire satisfaction of Engineer-in-Charge of work. Make. As per approved make list. NS-4

SITC of Havells make Single over hang circular arms of 1 mtr length , suitable to be mounted on Pole of 4 mtr - 9 mtr height. The Decorative arm should be made out of M.S. round tubular Pipe sections of 48mm Diameter attached to a pipe of 76mm dia to support suspended mounting of the LED Drop Down Post Top. The circular arm should properly welded to the pipe by means of 3 segments of 29mm diameter (as shown in the reference drawing). A decorative Cast Iron embellishment knob at the top of the 76mm pipe for aesthetics addition. Painted in Pure polyester Paint in approved colour shade of Pole. The Decorative arm to be approved by Engineer in Charge & Architect. Equivalent to Havells make Orbit D. with all labour and material required to complete the job in all respect up to the entire satisfaction of Engineer-in-Charge of work. NS-5.

S/E of 63 amp. 3 Pole/230V Astronomical automatic time switch of Indo Asian make Cat No. TL065ASO alongwith contractor of required capacity movement controlled by precisaty quartz osciliation operation on main supply of continue to run on built in rechageable nicket cadium cell for 150 hours in the evnt of power failure including cost of contractor complete in all respect upto the entire satisfaction of Engineer-in-charge of the work. NS-6

Highlight Associates and Contractors