SPECIAL REPAIRS TO OTM BLDG NOS. P 122, P 123 AND T 73 AND CERTAIN REVENUE MINOR WORKS AT MIL STN DHRANGADHRA

Amount

M&L for excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation etc or for shaft, wells, cesspits, manholes, pier holes etc not exceeding 10 sqm on plan and getting out in hard/dense soil complete all as specified and directed.

M&L for returning, filling in, including, spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick in any type of soil complete all as specified and directed.

M&L for removing excavated material (soil), not exceeding 50m and depositing where directed at level not exc 1.5m above the starting point complete all as specified and directed.

M&L for for moorum/red bajri filling floors or pavings, laid in layers not exc. 15cm thick, spread, levelled and rammed including watering complete all as specified and directed.

M&L for plain cement concrete (1:5:10) type E-2 using 40 mm graded stone aggregate in filling into sunken floor and mass concrete complete all as specified and directed.

M&L for plain cement concrete (1:4:8) type D2 using 40 mm graded stone aggregate in foundation filling and mass concrete complete all as specified and directed.

M&L for plain cement concrete (1:2:4) type B-2, using 40 mm graded stone aggregate as in foundation, filling, Bed blocks and mass concrete complete all as specified and directed. Note:- Volume of column embedded in PCC shall be deducted for payment purpose.

M&L for plain cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate in foundtion of pole/stay assembly etc including necessary form work, all as specified and directed.

M&L for pre-cast cement concrete (1:3:6) type C1 using 20 mm graded stone aggregate as in landings, cover slabs (for manholes etc) with plain fair faces, including chamfers, weathering, throating etc and set in cement mortar (1:6) complete all as specified and directed.

M&L for RCC 1:2:4 , type B-1 using 20mm graded stone aggregate suspended slabs supported on walls/columns, in floors, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for Brick work with old size, sub class 'B' bricks, straight or curved on plan exc. 6m mean radius built in cement mortar (1:6) complete all as specified and directed.

Cutting chases, pinning in, making good to facings in stone concrete block or slab walls where required and pointing in cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting exceeding 20 cm girth complete all as specified & directed.

M&L for walling of random rubble stone masonry, uncoarsed, well bonded, bedded and solidly hearted, built in cement mortar 1:6 complete all as specified and directed.

M&L for walling of random rubble stone masonry, brought up to courses, well bonded, bedded and solidly hearted, built in cement mortar (1:6) but except stone complete all as specified and directed.

Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints, as specified, of random rubble walling, uncoursed or brought upto course with maximum depression on face from straight edge held against the dressed surface not.exc. 20mm for sand stone complete all as specified and directed.

M&L for form work to soffit of suspended slabs such as roof slabs, floor slabs, landings and simillar works not exceeding 20cm thick and fair finished surfaces of concrete all as specified and directed.

M&L for formwork to edges of concrete flats, treads, break in floors, window cills, concrete wall, floor and roofs n exc 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping or similar work exc 10 cm but n exc 20 cm wide and fair finished surfaces completed all as specified and directed.

S&F, 35 mm thick, 2nd class hard wood, factory made, glazed & skeleton shutters, open rebated and prepared to receive glass, gauze etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc. Sizes of members of shutters as specified in SSR Part I, Section 8, Clause 8.24 (a) complete all as specified and directed.

S&F, 35 mm thick, 2nd class hard wood factory made, plain, framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F factory made 30mm thick flush shutters, solid core construction, with block board core and plywood face panles, commercial type on both sides complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc. 1.5sq.m each complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutter from the frames) exc. 1.5sq.m but not exc. 4sq.m each complete all as specified and directed.

Taking down old shutters of any description exc. 1 sqm but not exc. 2 sqm each complete all as specified and directed.

Taking down steel window/ventilator including grills of any description, n. exc 1.5 Sqm each complete all as specified and directed

S&F, factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tube for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at site complete all as specified and directed.

S&F, solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube, supplying and fixing in opening as per specifications complete all as specified and directed.

S&F, aluminium anodised, barrel tower bolts of extruded section with length of bolt 200 mm and fixed complete all as specified and directed

S&F, aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy with length of bolt 250 mm and fixed complete all as specified and directed.

S&F, butt hinges, medium weight, cold rolled, mild steel of size 100 mm complete all as specified and directed.

S&F, 150mm size, aluminium handles, cast type, anodised complete all as specified and directed.

S&F, 150 mm size extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F in repairs, brass, chromium plated tubular towel rail 20mm dia 60CM long between flanges complete all as specified and directed.

S&F, 150mm long floor door stopper of aluminium alloy body and tongue with hard drawn steel springcomplete all as specified and directed.

S&F, galvanised mild steel wire cloth 0.63 mm nominal dia of wire and average width of aperture 1.40mm and fixed wth tinned tacks or galvanized wire staples or wooden bead complete all as specified and directed.

S&F, stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

M&L for mild steel framed work such as grills, gratings, etc. with ends of bars, shouldered and/or riveted, or forged into spikes, framed guard bars etc and similar work conforming to Fe-290 (Gde-E-165) including applying one shop coat of red oxide primer complete all as specified and directed

S&F, Mild steel bolts purpose made with hexagonal or square head one end and screwed the other, or screwed both ends each screwed end to be fitted with washers and one hexagonal or square nut. Exc 30cm long dia of neck in exc 12mm and n. exc 20mm complete all as specified and directed.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M&L for mild steel TMT bars 6 to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M&L for MS rolled sections (Fe 410-W (Gde-E-250) quality-A) as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors fixed with angle cleats or other connecting plates including one shop coat of zinc chrome primer complete all as specified and directed.

S&F, mild steel work in plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes without any attachment conforming to Fe-290 (Gde E-165) complete all as specified and directed. complete all as specified and directed.

S&F, MS angle iron Fe-410-W (Gde-E-250) quality A in framed work for roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle channel or flat sections) including distance pieces, cleats etc incl one shop coat of zinc chrome primer complete all as specified and directed.

M&L for rolled mild steel angle iron work as in door frames complete, drilled for fixing of hinges etc. also fastening and fixing conforming to Fe-290 (Gde-E-165) complete all as specified and directed.

S&F, Aluminium anodised doors/windows/ventilators with one or more rebates including joining cleat for fixing etc complete with frame and shutter of size directed by Engineer-in-charge including handles, tower bolts, etc complete all as specified and directed. Note:- Floor door spring, sheet glass, wire cloth, lock, rubber gasket, etc shall be measured and paid seperately.

S&F, pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet, 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F, pre-painted galvalume aluminium zinc coating GI based plain steel sheet, 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F, in repair, false ceiling, at any height, 600 x 600mm grid with Armstrong 'Prelude XL 32' grid system and 16mm thick mineral fibre acoustic tile 'RH - 99 Classic lite' with suspension system complete all as specified and per manufacturer's instruction. Make : Armstrong or equivalent as approved by GE.

M&L for machine cut kota stone slab, 20-25mm thick as in skirting laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab, rubbing and polishing,over and including screed bed 10mm thick in CM (1:3), complete all as specified and directed.

M&L for 50mm thick cement concrete 1:3:6 type C1, using 20mm graded stone aggregate as in plinth protection, finishing cement concrete surfaces even and smooth without using extra cement, Joints of plinth protection shall be filled with bitumen mastic (1:3) complete all as specified and as directed.

M&L for 75 mm thick cement concrete (1:3:6) type C-2 using 40 mm graded stone aggregate as in sub base of flooring/hard standing, path and finishing the surface even and fair without using extra cement complete all as specified and directed.

M&L for glazed ceramic coloured tiles of size 350 x 250 x 7mm/ 450mm x 350mm x 7mm on vertical surface such as skirting, dados, risers to steps etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, laid over and including cement plaster 10mm thick in cement mortar (1:4) , complete all as specified and directed.

M&L for glazed ceramic coloured tiles of size 350 x 250 x 7mm/ 450mm x 350mm x 7mm on vertical surface such as skirting, dados, risers to steps etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, laid over and including cement plaster 10mm thick in cement mortar (1:4) , complete all as specified and directed.

M&L, Non-skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete as specified and directed.

M&L for coloured glazed ceramic tiles of size 350 x 250 x 7mm/450x350x7mm thick highlighter on vertical surface such as skirting/dado, set and jointed in net cement slurry and pointed in colour cement to match over 10 mm thick backing coat in CM 1:4 complete all as specified and directed.

M&L, Non-skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular), area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set & jointed in net cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete as specified and directed.

M&L, Non-skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular), area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm, as in skirting/dado etc. set & jointed in net cement slurry and pointed in white or coloured cement to match over and including 10mm thick screed bed in CM 1:4 complete as specified and directed.

M&L for vitrified tiles, 10mm thick (minimum), (square/ rectangular) polished, area of each tiles exceeding 0.36 Sqm (including 600mmx600mm size) but not exceeding 0.42 Sqm, in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles and over and including 15mm thick screed bed in CM (1:6) complete all as specified and directed.

M&L for vitrified tiles, 10mm thick (minimum), (square/ rectangular) polished, area of each tiles exceeding 0.36 Sqm (including 600mmx600mm size) but not exceeding 0.42 Sqm, in skirting/dado, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles and over and including 10mm thick rendering in CM (1:4) complete all as specified and directed.

M&L, for machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size conforming to IS 15658- 2006 of 60mm thickness, M-35 grade including 25mm thick sand cushion below paver blocks complete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) and removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for rendering cement plaster 10mm thick in cement mortar 1:3 on fair faces of concrete in ceilings, chajjas, fins facia etc. finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 10mm thick in cement mortar 1:6 on stone masonry surface or surface other than fair face of brick work finished surface even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1:6 on stone masonry surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick cement plaster 1:4 on stone masonry surface or surface other than fair face of brickwork surface finished even and smooth without using extra cement.

Taking down cement plaster on brick or stone wall etc. including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed.

M&L for preparing new plastered or un-plastered walls surfaces and applying three coats white wash complete all as specified and directed.

M&L for preparing old plastered or un-plastered surfaces and applying one coat of white wash on walls complete all as specified and directed.

M&L for preparing of new plastered or un-plastered wall surfaces and applying two coats of oil bound distemper over and including chalk whiting on plastered surfaces, preparatory to distempering complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of cement base paint over a coat of white cement as primer complete all as specified and directed.

M&L for complete removal of existing treatment and preparation of plastered surfaces of walls and applying two coat of cement base paint complete all as specified and directed.

M&L for complete removal of existing treatment (with mechanical scrubber) and preparation of old plastered or un-plastered surfaces and applying two coats of oil bound distemper over and including one coats of Birla/JK wall care putty complete all as specified and directed.

M&L for complete removal of existing treatment (with mechanical scrubber) and preparation of old plastered or un-plastered surfaces of wall and applying two coats of cement base paint over a coat of primer complete all as specified and directed.

M&L for preparing new plastered or un-plastered ceiling surfaces and applying three coats of white wash complete all as specified and directed.

M&L for preparing old plastered or un-plastered surfaces and applying one coat of white wash on ceiling complete all as specified and directed.

M&L for 4mm thick sheet glass, ordinary quality and glazing with oil putty in square not exc. 0.5sq.m in each pane complete all as specified and directed.

M&L for 3mm thick figured glass, ordinary quality and glazing with oil putty in square not exc.0.5 sq.m in each pane complete all as specified and directed.

M&L for preparation of old wooden surface of any description, over 10cm width or girth and applying one coats of synthetic enamel paint complete all as specified and directed.

M&L for preparation of new wooden surface of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

M&L for preparation of old painted steel surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of new steel surface of any description exc. 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

M&L for preparation of new steel surface of any description exc. 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

Taking up or down steel tubing and connections for 15mm bore of pipe complete all as specified and directed.

Taking up or down steel tubing and connections for 20mm bore of pipe complete all as specified and directed.

Taking up or down steel tubing and connections for 25mm bore of pipe complete all as specified and directed.

S&F, steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors for 15mm bore of pipe complete all as specified and directed.

S&F, steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors for 20mm bore of pipe complete all as specified and directed.

S&F steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors for 25mm bore of pipe complete all as specified and directed.

Refixing old serviceable steel tubing and connections in new or old position (walls, ceilings, floors etc.) for 15mm bore of pipe complete all as specified and directed.

Refixing old serviceable steel tubing and connections in new or old position (walls, ceilings, floors etc.) for 20mm bore of pipe complete all as specified and directed.

Refixing old serviceable steel tubing and connections in new or old position (walls, ceilings, floors etc.) for 25mm bore of pipe complete all as specified and directed.

S&F, in repair, 25mm dia, powder coated, fancy type, aluminium decorative tubular curtain rod with decorative ball type side brackets complete all as specified and directed.

S&F, in repair, brass chromium plated, tubular towel rail 20mm dia, D type, 600mm long complete all as specified and directed as per Cat No. ACN 1111NM of Make Jaquar or equivalent make as approved by GE from Appendix 'C'.

S&F, in repair, chromium plated over head shower 100mm dia round shape single flow (ABS body chrome plated with Gray face plate) with rubit cleaning system complete all as specified and directed as per Cat No. EOS-542N of ESSCO or equivalent make approved by GE from the make specified in Appx 'C'.

S&F, in repairs, 15mm brass chromium plated bib cock with wall fange, complete all as specified and directed as per Cat No. MQT-511 of ESSCO or equivalent make approved by GE from the make specified in Appx 'C'.

S&F, in repair, stop valve, angular, chromium plated for iron pipe or for unions and fixed to 15mm bore pipe complete all as specified and directed as per Cat No - MQT - 513A of Make : ESSCO or equivalent as approved by GE complete all as specified and directed.

S&F, in repair, concealed stop cock of 15mm, heavy body casted, chromium plated for iron pipe or for unions and fixed to 15mm bore pipe complete all as specified and directed as per Cat No - MQT - 514A of Make : ESSCO or equivalent as approved by GE complete all as specified and directed.

Supply, fixing and installation of office compactor complete set of 03 or 04 unit of size 1.20 x 0.50 x 2.00mtr), superior and prime quality of steel (Powder coated) with wheel and rail and base frame made of channel and angle section including suitable shelves for office files and books etc and lockehead for entire system with single locking operation, stoppers, anty dust solution with long durability complete all as specified and directed. Make - Methodex or equivalent as approved by GE.

S&F, in repairs, 50mm bore, low density polyethelene pipe (HDPE) of pressure rating 6kgf/sq.cm fixed to walls, ceilings or in floors etc. complete all as specified and directed.

Supply, hoisting, fixing in position and connecting, in repairs, 500 litres capacity rotational moulded polyethylene water storage tank double layered (cylindrical, vertical with closed top), ISI marked, including fixing arrangement for inlet/outlet/over flow and vent pipe of standard size all as specified in SSR Part-I complete all as specified and directed.

Supply, hoisting, fixing in position and connecting, in repairs, 1000 litres capacity rotational moulded polyethylene water storage tank (cylindrical, vertical with closed top) including fixing arrangement for inlet/outlet/over flow and vent pipe of standard size all as specified in SSR Part-I complete all as specified and directed.

S&F, in repair, bib taps, cast copper alloy, fancy type, chromium plated, screwed down, screwed for iron pipe or brass ferrule of 15mm bore complete all as specified and directed.

Supply only, pillar taps cast copper alloy with capstan head, chromium plated, screwed down high pressure, with or without lettered ‘hot’ or ‘cold’ with long screwed shanks and fly nuts, screwed for iron pipes 15mm bore complete all as specified and directed.

Supply only, pillar taps cast copper alloy with capstan head, chromium plated, fancy type, screwed down high pressure, with or without lettered ‘hot’ or ‘cold’ with long screwed shanks and fly nuts, screwed for iron pipes 15mm bore complete all as specified and directed.

S&F, stop valves, cast copper alloy, fancy type, chromium plated screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipes or for unions of 15mm bore complete all as specified and directed.

S&F, in repair, stop valves, cast copper alloy, fancy type, chromium plated screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipes or for unions of 15mm bore complete all as specified and directed.

S&F, 20mm bore, ball valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed complete all as specified and directed.(Minimum weight -210 Gms)

S&F, in repair, 20mm bore, ball valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed complete all as specified and directed. (Minimum weight -210 Gms)

S&F, PVC connection 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed.

S&F, 75mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints laid in trenches or floor complete all as specified and directed.

S&F, 110mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints laid in trenches or floor/walls complete all as specified and directed.

S&F, 75mm bore PVC (SWR) bend, any radius, with access door complete all as specified and directed.

S&F, 110mm bore PVC (SWR) bend, any radius, with access door complete all as specified and directed.

S&F, 110mm bore PVC (SWR) junction single, (Single T) equal or unequal with access door complete all as specified and directed.

S&F, 75mm bore PVC (SWR), vent cowl complete all as specified and directed.

S&F, 110mm bore PVC (SWR), vent cowl complete all as specified and directed.

S&F, PVC (SWR) floor trap, with chromium plated grating including jointing with solvent cement, dia of outlet 75mm complete all as specified and directed.

S&F, PVC (SWR) gully trap 125/110mm, setting and jointing with solvent cement complete all as specified and directed.

M&L for cement concrete (1:3:6) type C-2 using 40 mm graded stone aggregate as in bed to drain pipes including packing under and hunching against the sides of pipe after they are laid and tested for 150mm bore of pipe complete all as specified and directed.

M&L for cement concrete (1:3:6) type C-2 using 40 mm graded stone aggregate as in bed to drain pipes including packing under and hunching against the sides of pipe after they are laid and tested for 200mm bore of pipe complete all as specified and directed.

M&L for salt glazed stone ware drain pipes, 150mm internal diameter, grade 'A' laid in trenches and jointed complete all as specified and directed.

M&L for salt glazed stoneware drain pipes, 200mm internal diameter, grade 'A' laid in trenches and jointed complete all as specified and directed.

Cutting into existing manholes for cnnecting new drain pipes, making good to pipes and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cment concrete (1:2:4) type B1, using 20mm graded stone aggregate, smooth finished and reforming benching as required for 200mm bore of pipe complete all as specified and directed.

S&F, in repair, vitreous china squatting pan, 'Orissa’ pattern, white of size 580mm x 440mm with integral foot rest, P or S trap (excluding flushing cistern and flush pipe) complete all as specified and directed.

S&F in repair, vitreous china bowl urinal flat back, of size 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, fixing flush pipe grating and union for discharge pipe including urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms). (exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and directed.

S&F, in repair, 10 litres capacity, PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet ball valve, float and handle including brackets and connection to pipe or lever etc. complete all as specified and directed.

S&F, Vitreous china wash basin, white, flat back of size 550mm x 400mm including waste fitting and brackets, 32mm bore brass waste fitting chromium plated and PVC Connection of 15mm size with PTMT nuts of length 600mm complete all as specified and directed.

S&F, in repair, vitreous chinas wash down water closet pan (pedstal pattern), white including connection to drain (or outgoing pipe) and to flushing pipe, fixing of plastic seat, black, closed pattern with flat bottom and cover and mild steel chromium plated or alumninium hinging device complete all as specified and directed. (Note:- Supply only Plastic sheet cover shall be measured and paid separately)

S&F, soap dish, vitreous china white, approximate size 160x 160x90mm complete all as specified and directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc. complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exc. 15cm thickness (below or above ground level) all as specified and directed.

Dismantling of reinforced cement concrete of any description and in any position not otherwise specifically provided for, reinforcement cut as required to facilitate demolition complete all as specified and directed.

Dismantling timber scantlings 40 sq. cm and over in section (framed), in any position complete all as specified and directed.

Dismantling timber scantlings 40 sq. cm and over in section in fillets rails, posts, rafters, purlins etc in unframed work complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for.

Dismantling asbestos cement (corrugated, semi corrugated etc.) sheets in roof covering complete all as specified and directed.

Dismantling of cast iron, PVC or reinforced concrete drain pipes jointed in cement mortar and taking out of trenches if required for 110mm and 75mm bore of pipe complete all as specified and directed.

Dismantling of cast iron, PVC or reinforced concrete drain pipes jointed in cement mortar and taking out of trenches if required for 150mm bore of pipe complete all as specified and directed.

Demolition and breaking up drain pipes (slat glazed stoneware, AC or RCC) set in cement mortar for 200mm bore of pipe complete all as specified and directed.

Dismantling of cast iron or reinforced concrete drain pipes, 100mm bore, jointed in cement mortar and taking out of trenches complete all as specified and directed.

Taking down carefully unserviceable copper/aluminium point wiring (Light, fan, socket or power) complete including unserviceable fittings and fixtures such as switches, ceiling roses, pendents, regulators, sockets, lamp holders, brackets, except ceiling fittings, bulk head fittings, tube light fittings etc. and making good the disturbed surfaces of walls, floors, etc. complete all as specified and directed.

M&L for wiring with and including multistranded copper conductor 1.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed FRLS cable 1100 Volts grade, ISI marked with valied CML number drawn in and including medium grade PVC casing and capping double lock type 32mm in size, fire resistant, ISI marked including with its fittings and fixtures such as tees, bends, elbows, junction boxes, etc. including multistranded copper conductor 1.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed FRLS cable 1100 Volts grade, ISI marked with valied CML number as continuity earth wire and including pressed steel sunken concealed terminal box with 3mm thick industrial laminated sheet cover for mounting switches, sockets and fan regulators etc. complete all as specified and directed for the following :-

(a) One light/fan point controlled by one switch

(b) One 3 pin, 5 Amps, socket outlet on the same board controlled by another switch.

(c) One multi pin 5 Amps, socket outlet on Independent board.

M&L for wiring with and including multistranded copper conductor 2.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed FRLS cable 1100 Volts grade, ISI marked with valied CML number drawn in and including medium grade PVC casing and capping double lock type 32mm in size, fire resistant, ISI marked including with its fittings and fixtures such as tees, bends, elbows, junction boxes, etc. including multistranded copper conductor 1.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed FRLS cable 1100 Volts grade, ISI marked with valied CML number as continuity earth wire and including pressed steel sunken concealed terminal box with 3mm thick industrial laminated sheet cover for mounting switches, sockets and fan regulators etc. for one 3 pin, 15 Amps socket outlet point on independent board complete all as specified and directed.

S&F, switch piano, flush button, single pole, one way, 5 Amps complete all as specified and directed

S&F, switch piano, flush button, single pole, one way 15 Amps complete all as specified and directed

S&F, socket outlet, 2 in 1, 3 pin, 15 Amps and 5 Amps flush type complete all as specified and directed

S&F, socket outlet, 2 in 1, 3 pin, 5 Amps, flush type complete all as specified and directed

S&F, Isolator, SPN, 40 Amps, 240 Volts fixed in sheet metal board complete all as specified and directed.

S&F, Isolator, TPN, 63 Amps, 415 Volts fixed in sheet metal board complete all as specified and directed.

S&F, in repairs, sheet metal distribution board, factory made and tested complete, protection class IP-42 suitable for mounting MCBs, isolator with 200 A tinned copper bus bar of capacity 200 Amps of SPN, 4 way 240 Volt complete all as specified and directed

S&F, in repair, sheet metal distribution board, double door factory made and tested complete, protection class IP-42 suitable for mounting MCBs, isolator with 200A tinned copper bus bar of capacity 200 Amps, 3 phase with neutral of 4 way 415 Volt complete all as specified and directed.

S&F, ceiling rose, 3 terminal , any shade, of PVC/Polycarbonate, isolated body complete all as specified and directed

Supplying & laying, in repairs, XLPE insulated, PVC inner sheathed, armoured with galvanised steel strip or wire heavy duty underground cable with aluminium multi stranded conductor, 1100 volt grade, laid in trenches/duct, passing through pipe/duct or fixed on pole and connecting and testing complete including taking down old unserviceable cable all as specified and directed of 25 Sqmm, 4 core sizes of cable.

S&F, in repair, Ceiling fan 1200mm sweep, SP, 230/240 Volts 50Hz, white colour, with copper winding including down rod and canopy etc. including making connection with 1.5 Sqmm copper conductor cable from ceiling fan to connector and writing of MES Nos with black synthatic enamelled paint complete all as specified and directed. Make of Bajaj or equivalent make approved by GE from the make specified in Appx 'C'. Note : Old/unserviceable fans shall be deposited in MES Store as directed by Engineer-in-Charge.

S&F, miniature circuit breakers, type curve ‘C’ , SPN, 32 Amps, 240 Volts fixed in sheet metal board complete all as specified and directed.

S&F, miniature circuit breakers, SP, 6-32 Amps, 240 Volts fixed in sheet metal board complete all as specified and directed.

S&F, in repair/replacement, LED light fitting, batten type, 1 x 20 watt including lamp and connecting up complete with white PVC insulated and PVC sheathed round flexible twin core copper conductor cable of suitable size and testing on completion all as specified and directed. Make : Bajaj or equivalent make in Havells.

S&F, in repairs, LED light fitting, batten type, housed in extruded from powder coated aluminium, 9 watt for soft diffuser lighting with and including lamp and connecting up complete with white PVC insulated and PVC sheathed round flexible three core copper conductor cable of suitable size and testing on completion all as specified and directed. Make: As per Cat No. BAJAJ LED BATTEN 9W (Item Code 830102) of Bajaj or Cat No. LHEXBQP51N1W009 of Havells equivalent as approved by GE from the make specified under Appx 'C'.

S&F, Exhaust Fan, 250mm Sweep, single phase, 230/240 volts, including making opening for exhaust fan including grouting nut, bolts and washer for fixing of fan and making good the disturbed surfaces all as per existing and mounting fan including connected with suitable three core copper conductor cable complete all as specified and directed. Make as approved by GE from the make specified in Appx 'C'.

S&F, in repairs, stepped type electronic fan regulators, 120W/280V complete all as specified and directed. Make- Anchor Cat No. 33070 or equivalent as approved by GE.

S&F, in repairs, sub-main wiring with 2 single core, 4 Sqmm PVC insulated, unsheathed, 1100 Volts grade, FRLS, copper multi stranded conductor drawn in and including PVC concealed conduit and conduit acessories including drawing one run of PVC insulated, unsheathed, 1100 Volts grade, FRLS, copper conductor multi stranded, 2.5 Sqmm size as continuous earth wire drawn through and connected to main switch/DB and testing on completion complete all as specified and directed. Note: (i) 2 runs of main conductor, one run of earth conductor and one run of PVC conduit and acessories shall be measured as one unit length.(ii) Rate quoted shall deemed to includes cuttings chases for consealing PVC conduit and making good the disturbed surfaces in CM 1:3 complete.

M&L,earthing complete with galvanized steel earth plate electrode of 60 cm x 60 cm x 6mm thick buried directly in ground [earth pit not less than 2.25 metre deep below normal ground level] with top edge of the plate not less than 1.5 m below normal ground level, connected to galvanized earth wire of 4mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical plate No. 3 of MES SSR Part I all as specified and testing on completion including provision of earth lead protected by 15 mm dia light grade GI pipe & watering pipe shall be 20 mm bore medium grade GI pipe including all excavation and earth work in any type of soil, PCC pit with RCC cover, char coal, salt, funnel etc complete. Note : Rate quoted by tenderers shall be deemed to include for following provisions;-[i]. Excavation & earth work in any type of soil including removing of surplus material upto 50 M.[ii]. PCC 1:3:6 type C1 using 20mm graded stone aggregate in pit & 40mm thick precast RCC 1:2:4 type B1 cover 50x50 cm with 8mm TMT bars @ 10 cm C/C both ways with handles.[iii]. Main earthing lead from earth electrode to test point upto 7.5 mtr.[iv]. Funnel with watering pipe [GI pipe] 20mm bore [ISI marked] medium grade & copper lugs, charcoal & salt as reqd.[v]. GI protection pipe of size 15 mm bore light grade 7.5m.

partechengineers

Haritwal traders