CONSTRUCTION OF MULTI-PURPOSE INDOOR SPORTS FACILITY

BoQ_Ver3.0

Tender No: GAIL/BDA/CNP/AKM/25/W-23 (Tender ID: 2025_GAIL_252260_1)

Name of the Bidder/ Bidding Firm / Company :

PRICE SCHEDULE (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only )

NUMBER #

CIVIL WORKS

Supplying and filling approved SAND of specified quality under floors, in foundations, plinths, tank foundations etc. for all depths and heights including cost of sand,royalties, transportation to site for all leads and lifts,including loading, unloading, spreading in layers of loose thickness not exceeding 150 mm,watering,ramming,compacting with mechanical compactors and/or other equipment to the specified levels to achive 85% relative density as per IS:2720 Part XIV,including preparation of subgrade to the required slope,providing testing apparatus and testing the degree of consolidation all complete as per drawings, specifications and direction of Engineer-in-charge.The rates shall be inclusive of the cost of all labour,material,equipments etc. all complete .

Site clearance by demolition of listed work by manual or mechanical means including removing the debris and disposal of unserviceable material to any lead and staking of serviceable materials, handing over serviceable material to concerned department if required as per technical specifications and direction of Engineer-in-charge. Note: 1. Rate includes cost of all labour, tools, tackles, hire charges, royalties, levies, leads, loading/unloading, transportation, water, electric power, illumination etc. complete in all respects as per scope of work, detailed construction drawings, technical specifications and direction of Engineer-in-charge. 2. Demolition will be paid in NET CUM as demolished.

Demolishing of Brick Work In cement mortar

Demolition of R.C.C work of all concrete Grades including stacking of Reinforcement.

Dismantling unreinforced cement concrete concrete (PCC) of mix 1 : 2 : 4 , and leaner mixes including IPS flooring

Dismantling of tile & kota stone flooring Dismantling tile work in floors and roofs laid in cement mortar For thickness of tiles 10 mm to 25 mm

Dismantling of the existing china mosaic waterproofing from terrace

Earth work in Excavation below ground level for all kinds of works in ALL TYPES OF SOIL as classified in specification for a depth upto 1.5m including removal of vegetation, shrubs and debris, cutting and dressing of sides in slopes, levelling, grading and ramming of bottoms, dewatering of accumulated water from any source and keeping the surface dry for subsequent works and disposal or stacking of excavated material within a lead of 100m, as directed including providing temporary supports to existing service lines like water pipes, sewage pipes, electric overhead and underground cables etc. all complete.

For depth beyond 1.5m and upto & inclusive of 3.0m.

For depth beyond 3.0m and upto & inclusive of 4.5m.

EARTHWORK IN FILLING including supply by excavating the earth from BORROW AREAS arranged by CONTRACTOR for all leads, transporting the earth from borrow area including cleaning & stripping the earth at borrow areas, breaking clods, loading, unloading and laying at all depths and heights in layers of thickness not exceeding 15 cms., watering, rolling and ramming by manual methods/mechanical compactors to achieve 90% of the maximum laboratory dry density, dressing, trimming, levelling the top surface etc. in foundations, plinths, trenches etc. all complete.

Transporting and disposing the SURPLUS EARTH AND DEBRIS including shrubs and vegetations from construction area beyond the initial lead of 100M including re-excavating the deposited soil excavated earlier, transportation, loading, unloading, laying at all depths and heights, stacking, levelling and dressing both the area (viz. from where the earth is transported and where it is deposited) to required levels and slopes complete with all lifts as directed. For carting on the basis of truck measurements (volume of truck reduced by 30% for voids) i) Upto 1.0Km.

Providing and laying PLAIN CEMENT CONCRETE for all depths below and upto plinth level in foundations,drains, fillings, non-suspended floors, pavements & ramps or any other works etc. including shuttering, tamping, ramming, vibrating, curing, shuttering etc. all as specified in any shape, position, thickness and finishing the top surface rough or smooth as specified and directed all complete for concrete of nominal mix 1:3:6 by volume (1 Cement: 3 Coarse Sand: 6 Crushed Stone Aggregates/Gravels with 40mm and down size graded crushed stone aggaregates.

Providing and laying REINFORCED CEMENT CONCRETE OF M-25 GRADE with 20mm and down size graded crushed stone aggregates/gravel in SUB-STRUCTURE of all types e.g. foundations, footings, raft, beams, slabs, pile caps, retaining walls, jambs, counterforts, buttresses, trenches, manholes,pipe encasement, catchpits, drains, RCC pits, equipment/machine foundations, pedestals, pipe sleepers, columns, plinth beams, suspended floors, beams, staircases, landings, steps, brackets etc. (including single pour concreting upto 250m3), including cost of admixtures if used,providing pockets, openings, recesses, chamfering etc., wherever required, vibrating, tamping, curing and rendering if required to give a smooth and even surface etc. all complete (excluding the Cost of Reinforcement and Shuttering) for all depths below and upto plinth level in any shape, position and thickness etc. all complete as specified, shown and directed.

Providing and laying REINFORCED CEMENT CONCRETE OF M-25 GRADE with 20mm and down size graded crushed stone aggregates/gravel in SUPER STRUCTURE in suspended floors, slabs, beams, columns, walls including counterforts, staircases, landings, steps, facias, fins, mouldings, gutters, shelves, windowsills, canopies, lintels, girders, ducts, brackets, chajjas with drip moulds, pedestals, posts, struts, equipment/machine foundations, ramps etc. (including single pour concreting upto 250m3) including cost of admixtures if used providing pockets, openings, recesses, chamfering wherever required, vibrating, tamping, curing and rendering if required to give a smooth and even surface etc. all complete (excluding the Cost of Reinforcement and Shuttering) for all heights above plinth level in any shape, position, thickness etc. all complete as specified, shown and directed.

Providing and fixing CENTERING AND SHUTTERING in foundations, footings, raft beams, slabs, pile caps, retaining walls, jambs, counter-forts, buttresses, trenches, equipment/machine foundations, pedestals, abutments, pipe sleepers, columns, plinth beams, lintels, suspended slabs, beams, staircases, landings, steps, non-circular tunnels/bunkers/silos/ shafts/ hoppers/liquid storage structures etc. including shuttering for single pour concreting, strutting, bracing, propping etc., keeping the same in position during concreting and removal of the same after specified period etc. for Straight/ Inclined Shuttering, keeping necessary provision for inserts, projecting dowels, anchor bolts or any other fixture etc. all complete and as specified and directed.

i) For all depths below and upto & inclusive of plinth level.

ii) For all heights above plinth level.

Providing temporary barricades of height 2.5 m and made of angle (or alternate) section and precoated GI sheet of 0.6mm wall thickness for isolation of area, provided with suitable glow signs, warning signs etc. including dismantling / removal and disposal of barricades after completion of job. Layout and location of barricades to be approved by Engineer In Charge. Barricades to be stable against wind and imposed loads without requirement of permanent foundations.

Supplying and placing in position HIGH STRENGTH DEFORMED STEEL BARS REINFORCEMENT (conforming to IS:1786, Grade Fe 415/500 ), for R.C.C. work including transporting the Steel, straightening, cleaning, decoiling, cutting, bending to required shapes and lengths as per details, binding with contractor's own 16 SWG black soft annealed binding wire at every intersection, supplying and placing with proper cover blocks, supports, chairs, overlaps, welding, spacers, fanhooks etc. for all heights and depths etc. all complete as directed.

Supplying, transporting, storing, fabricating in position and testing/examining bolted and/or welded STRUCTURAL STEEL WORKS at all levels and locations including all builtup sections/compound sections made out of rolled sections and/or plates/bent plates in trusses, purlins, wind ties, wind girders, columns, portals, racks, frameworks, crane gantries, surge girders, bracings, floor beams, lifting beams, monorails, platforms, staircases (excluding chequered plates and gratings), ladders, stoppers, brackets, side runners, sagrods, supports for equipment and technological accesories and process piping, hand railings, posts, conveyor galleries, trestles, towers, masts, junction houses etc., cutting to required size, straightening/bending if required, edge preparation, cleaning, preheating, bolting/welding of joints, (including sealing the joints of box sections with continuous welding), finishing edges by grinding, fixing in line and level with temporary staging & bracing and removal of the same after erection, grouting with Ordinary Grout or premix free flow Nonshrink Grout as specified, including preparation and submission of detailed fabrication drawings and applying primer after fabrication as per specification (for normal corrosive environment), etc. all complete

Site clearance by demolition of listed work by manual or mechanical means including removing the debris and disposal of unserviceable material to any lead and staking of serviceable materials, handing over serviceable material to concerned department if required as per technical specifications and direction of Engineer-in-charge. Note: 1. Rate includes cost of all labour, tools, tackles, hire charges, royalties, levies, leads, loading/unloading, transportation, water, electric power, illumination etc. complete in all respects as per scope of work, detailed construction drawings, technical specifications and direction of Engineer-in-charge. 2. Demolition will be paid in NET CUM as demolished.

80 x 1.2 mm MS laths with 1.20mm thick top cover

joints at locations approved by the architect.

Extra for providing mechanical device chain and crank operation for operating rolling shutters. Exceeding 10.00 sqm and upto 16.80 sqm in the area.

Supplying, transporting, storing, fabricating and fixing in position M.S. METAL INSERT (with lugs) of any shape made out of flats, plates, rolled sections, pipes etc. providing necessary templates, staging, cutting, straightening, if required, bolting, welding as required and embedding in position on both Plain and Reinforced Cement concrete members inclusive of adjusting shuttering & reinforcement/any other fixture, welding where necessary, tying and holding to correct level, line and position, any auxilliary dummy structures to support the heavy inserts, painting exposed surfaces with a coat of Red Oxide Zinc Chromate Primer etc. all complete for all depths and heights as specified and directed.

HAND RAIL (SS) Cost of providing and fixing 1 mtr height SS hand rail with necessary accessories.

Providing and laying BRICK MASONRY WITH BRICKS OF CLASS 7.5 in cement mortar 1:6 (1 Cement : 6 Sand) in one or more brick thickness and in any shape (excluding circular/curved brick masonry) AT ALL DEPTHS including the cost of materials, labour, scaffolding/ staging, sampling & testing, soaking of bricks, cutting and laying of bricks, providing recesses, making openings of any shape & size, finishing the joints flush below ground level and raking out the joints above ground level, sealing the gap between masonry and soffit of beam/slab, embedding the fittings & fixtures, curing, etc. all complete as per specifications.

Providing and laying BRICK MASONRY WITH BRICKS OF CLASS 7.5 in cement mortar 1:6 (1 Cement : 6 Sand) in one or more brick thickness and in any shape (excluding circular/curved brick masonry) AT ALL HEIGHTS including the cost of materials, labour, scaffolding/ staging, sampling & testing, soaking of bricks, cutting and laying of bricks, providing recesses, making openings of any shape & size, finishing the joints flush below ground level and raking out the joints above ground level, sealing the gap between masonry and soffit of beam/slab, embedding the fittings & fixtures, curing, etc. all complete as per specifications.

Providing and laying HALF BRICK MASONRY with bricks of CLASS 7.5 in cement mortar 1:4 (1 Cement : 4 Sand)in any shape, including the cost of materials, labour, scaffolding/staging, sampling and testing, soaking of bricks, cutting and laying of bricks, providing openings of any shape & size, raking out the joints, supplying and placing 2 Nos. 6mm dia. M.S. Bars at every fourth course, sealing the gap between masonry and soffit of beam/slab, embedding the fittings and fixtures, curing etc. all complete as per specification.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

CEMENT PLASTER..External Walls 15 mm cement plaster on rough side of single or half brick wall of mix: 1:6 (1 cement: 6 coarse sand)

CEMENT PLASTER..Internal Walls 12 mm cement plaster of mix : (1 cement: 4 fine sand)

Wall painting with premium acrylic emulsion paint of INTERIOR grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Primer + 2 coats of acrylic emulsion of suitable colour.

EXTERNAL walls:- Providing & applying 3 coats of waterproofing decorative cement paint of approved make and approved shade, cleaning, including preparation of surfaces, base primer, curing etc. all complete

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete before internal painting of INTERNAL walls

Finishing EXTERNAL walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives. 13.48A.1 New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm

Vent pipe for WC (110 Φ) with COWL

Providing and fixing precoated galvanised steel sheet roofing accessories of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05 mm) with Zinc coating 120 gram per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : 1 Ridges plain (500 - 600mm)

Providing and laying 500 Gauge Low Density Polythene Sheet (LDPE) under flooring; including laps. Wastages etc. complete.

Providing and injecting approved chemical emulsions as specified for PRE CONSTRUCTION ANTI-TERMITE TREATMENT and creating a chemical barrier under and around column pits, wall trenches, basement excavations, top surfaces of plinth filling, junction of wall and floor, along the external perimeter of building, expansion joints, surrrounding of pipes and conduits etc. all complete as specified and directed. (Plinth area of the building at ground floor only shall be measured). Quoted rate is inclusive of all labour and material costs. With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades in dado, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. SIZE 600 x 1200.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

"Providing and fixing 12mm Frosted toughned float glass of approved brands (Saint Gobain, Sisecam, Modi Gaurd) along with aluminium glass edge protector having minimum 1.2 mm to 4mm thickness covering 15 to 20 mm on all the edges complete as per direction of Engineer-In-Charge. For Door (Openable) Portion:The price is inclusive of making holes/cutouts required for fixing fittings like floor spring, patch fittings, patch locks etc. in toughened glass wherever required as per direction of EIC.

Providing and fixing aluminium work for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) kg

Providing and fixing THERMALLY INSULATED precoated galvanised iron profile sheets (TATA BLUESCOPE OR APPROVED EQUIVALENT ) {size, shape and pitch of corrugation as approved by Engineer-in-Charge) of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. Under deck to be fused with insulation layer followed by protection coat. Total thickness 6mm

Providing & fixing 8mm thk Shera Board Panelling using shera Board sheets or equivalent, fixed to the wall with using suitable framework, screwed/ welded adequately, inclusive of giving neat hairline

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Fixing of (Re bars) Reinforcement bar using chemical of various diameter, using various drill upto a depth of 12 times dia of bar cleaning etc. complete as per manufacture’s specification including scaffolding.

Rebar Fixing with FISCHER FISV 360S Chemical 8mm Dia

Rebar Fixing with FISCHER FISV 360S Chemical 10mm Dia

Rebar Fixing with FISCHER FISV 360S Chemical 12mm Dia

Rebar Fixing with FISCHER FISV 360S Chemical 16mm Dia

Rebar Fixing with FISCHER FISV 360S Chemical 20mm Dia

INTERIOR WORK Providing and laying Vitrified tiles in FLOOR in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, levelling system and rubber mallet for placing the tiles gently and easily.

VITRIFIED TILES 1200 X 600

VITRIFIED TILES 600 X 600

Providing and fixing (Make-SUNDEK or approved equivalent) make Air cush wooden flooring (certified by BWF according to BWF standards - Grade 1A. Mix Grade African teak floorboard with imported oil based polish. Game line marking along with movable net and pole included in the price. Sub base : Rubber pad 18mm thk EPDM, with 45 x 70mm European SPF runners, 21mm thk floorboard. Total thickness : 84mm. Badminton court area 380 m2.

Providing and laying 3mm thick VINYL Tile / strip board flooring (WOOD PATTERN) over prepared surface ( IPS floor or equivalent) in Tennis court circulation areas.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. Granite stone slab of colour black, Cherry/Ruby red

Providing and laying damp-proof course 40 mm thick with cement concrete 1:2:4 (1 cement :2 coarse sand (zone-Ill) derived from natural sources :4 graded stone aggregate 12.5 mm nominal size derived from natural sources)

Providing & applying a coat of residual petroleum bitumen of gra

de of VG-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement sluny, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate

Providing and laying ANTI SKID AND MATT FINISH Vitrified tiles in floor indifferent sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to 15:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the jointswith white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Double charge vitrified tile polished finish of size 11.41A.1.1 Size ofTile 600 x 600 mm.( KITCHEN + TOILETS + GF WALKWAYS + BLDG OUTSIDE CORRIDOR)

Providing and fixing Acoustic panelling (Make: Knauf Armstrong or approved equivalent) 15mm thick, HERADESIGN FINE A2 ALPHA+ Finely textured wood wool acoustic tile with excellent fire reaction and good acoustics. The price shall include the GI Framework behind the Panel board.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length all complete and as directed by EIC (hold fast lugs or dash fastener shall be paid for separately).

Polishing with french polish on new wood and wood based surface to give an even surface including cleaning, the surfaceo fall dirt, dust and sand papering smooth and including a coat of wood filler.

Laminated sheet 1.00 mm thick

Providing and Fixing of all fittings as per direction of Engineer-In-Charge. Note: The hardware should be used of brands like Ozone,Hafele, Hettich,Taiton Double action double cylinder hydraulic floor spring of 120 kg (black) 500000 cycle tested , for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates complete as per the direction of Engineer-in-charge. a) Top patch b) Bottom patch patch c) Pivot d) Half Moon Door stopper (black pvdf/ teflon/ electrolating) e) Glass to glass lock or glass to wall lock f) Handle (25mm*302mm*450mm) h type

"Providing and fixing 12mm Frosted toughned float glass of approved brands (Saint Gobain, Sisecam, Modi Gaurd) along with aluminium glass edge protector having minimum 1.2 mm to 4mm thickness covering 15 to 20 mm on all the edges complete as per direction of Engineer-In-Charge. For Door (Openable) Portion:The price is inclusive of making holes/cutouts required for fixing fittings like floor spring, patch fittings, patch locks etc. in toughened glass wherever required as per direction of EIC.

Providing an fixing glazed shutters for doors, windows and clerestory windows using 4mm thick float glass, including ISI MARKED M.S. pressed butt hinges, bright finished of required size with necessary screws all complete and as directed by EIC. (Second class Teak wood 35mm thick)

Providing & fixing 1200mm x 600mm Armstrong - ARMSTRONG SIERRA OP SUPERFINE EDGE (BADMINTON COURT) as per RCP drawings with TEGULAR 15 GRID STRUCTURE WITH GI HANGING WIRE FROM FROM TRUE CEILING.The rate to include for rubbing, cleaning, surface preparation, cutting for light etc. complete.

Providing and fixing ISI marked flush door shutters decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 25 mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. piano hinges with necessary screws etc. all complete as directed by EIC.

"Providing and fixing panelled decorative shutters for doors, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note: Butt hinges and necessary screws and fittings shall be included in quoted rate) Second class teak wood 35 mm thick shutters"

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer’s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter cha

nnels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks)

PLUMBING WORKS

Providing, and installing counter top 30" x 18" double bowl SS kitchen sink with drain board and high arch faucets (2 nos), all complete with bottle trap and all acessories

Providing and fixing Urinal with fixing accessories complete including all cutting and making good the walls and floors wherever required, of make Jaquar: Product id -URS-WHT-13263 or Kohler: Product id -K- 26475IN-ER-0

Providing and fixing Urinal Sensor Complete Set with Installation Box (Battery Operated) complete including all cutting and making good the walls and floors wherever required, of make Jaquar: Product id -SNR-STL-51087 or Kohler: Product id K-24199IN-C01-CP

Providing and fixing wall mounted EWC with seat cover, Hinges, Fixing Accessories Set, S/P-Trap complete including all cutting and making good the walls and floors wherever required, of make Jaquar: Product id -DRS-WHT-37953BIUFSM or Kohler: Product id - K-20217IN-S-0

Providing and Fixing Concealed Tank, Installations Kit including all cutting and making good the walls and floors wherever required, of make Jaquar: Product id -JCS-WHT-2400S or Kohler: Product id -K-26351IN-M-NA

Providing and Fixing Control Plate (Flush Plate) including all fittings, of make Jaquar: Product id -JCP-CHR-352415 or Kohler: Product id -K-28476IN-M-CP

Providing and fixing C.P. brass long nose Two way bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. Make : Jaquar (OPP-CHR-15041PM)

Providing and fixing NAHANI GRATING 100MM DIA. MAKE : JAYNA (AC05 - 100X800X22)

Providing & fixing chrome plated brass battery based infrared sensor operated pillar cock, having foam flow technology. Single Lever Basin Mixer without Popup Waste, with 450mm Long Braided Hoses . Make : Jaquar (OPP-CHR-15011BPM)

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 . Make : Jaquar ( OPP-CHR-15053PM )

Providing and fixing Sensor Faucet for Wash Basin including all fittings, of make Jaquar: Product id -SNR-51449 or Kohler: Product id -K-24270IN-ND-CP

NR VALVE (3/4") Cost of providing and fixing NR Valve fixed with necessary accessories.

Providing and fixing Toilet Roll holder with stainless steel flap including all fittings, of make Jaquar: Product id -AKP-35753PS or Kohler: Product id -K-5633IN-CP

Providing and fixing Automatic Soap Dispenser with Complete Set of make Jaquar: Product id - SDR-BLC-DJ0160AS or Dolphy: Product id -DSDR0112-S

Providing and fixing HAND DRYER with Complete Set of make Jaquar: Dyson: Product id - Airblade Db

Providing and fixing Bottle Trap for Wash Basin including all fittings, of make Jaquar: Product id -ALD-769L300x190 or Kohler: Product id -K-16407IN-CP

GRANITE COUNTER Cost of providing and fixing with necessary accessories.

Providing and fixing Hand Shower (Health Faucet) including all fittings of make Jaquar: Product id -ALD-573 or Kohler: Product id -K-98100IN-0

Providing and fixing wash basin with fixing accessories all complete of make Jaquar: Product id -JDS-WHT-25907N or Kohler: Product id -K-25316IN-0

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. Providing and fixing C.P. brass Towel rack of approved quality conforming to IS:8931 . Make : Jaquar Towel Rack (AHS-CHR-1581)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing Rectangular shape 1500x450 mm

15 mm nominal dia Pipes

20 mm nominal dia Pipes

25 mm nominal dia Pipes

32 mm nominal dia Pipes

PROVIDING AND FIXING SWR UPVC Pipe (Drainage) MAKE: ASHIRVAD/ PRINCE/ JAIN, WITH ADHESIVE SOLVENT FOR CONNECTION / JOINTS.

87.5 DEG BEND

87.5 DEG DOOR BEND

32 mm nominal dia Pipes

PROVIDING AND FIXING SWR UPVC Pipe (Drainage) MAKE: ASHIRVAD/ PRINCE/ JAIN, WITH ADHESIVE SOLVENT FOR CONNECTION / JOINTS.

110mm dia. - SOLVENT WELD (3 METERS LONG)

87.5 DEG BEND

BEND 45 DEG

SINGLE TEE

75mm dia. - SOLVENT WELD ( 3 METERS LONG)

OH TANK...Supply, transportation and erection of 500 liters SINTEX/Penguin/Supreme water tanks with inlet piping of 1/2 inch and outlet pliping 0f 3/4 inch including auto start / cut facility once the tanks are empty / full

Rain water down takes (150 Φ) PVC

BoQ_Ver3.0

Tender No: GAIL/BDA/CNP/AKM/25/W-23 (Tender ID: 2025_GAIL_252260_1)

Name of the Bidder/ Bidding Firm / Company :

PRICE SCHEDULE (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only )

NUMBER #

INLET PIPING (3/4" GI) TO OH TANK

OUTLET PIPING (1/2" PVC) TO OH TANK

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed

with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge : With average thickness of 120 mm and minimum thickness at khurra as 65 mm.

FIRE AND ELECTRICAL WORKS Supply, installation, testing and commissioning of Microprocessor based Intelligent addressable main fire alarm control panel (FACP) central processing unit with the following loop modules and capable of supporting not less than 240 devices(including detectors) and minimum 120 detectors per loop and loop length upto 2 km, network communication card, min. 320 characters graphics/LCD display with touch screen or other keypad and min. 4000 events history logs in the non volatile memory(EPROM), power supply unit 48 hrs. back up with 24volt sealed maintainence free battery with automatic charger. the panel shall have facility to connect printer to print out log and facility to have seamless integration with analog/digital voice evacuation system and shall be complete with all accessories. the panel shall be compatable for IBMS system with open protocol BACNet/Modbus over IP complete as per specifications.

2 Loop Panel

Supply, installation, testing and commissioning of Repeater Panel with 320 character/Touch screen LCD display with inbuilt reset, acknowledge and silence switches complete as required.

Supply, installation, testing and commissioning of intelligent Analog Addressable photothermal detector complete with mounting base complete as required.

Supply, installation, testing and commissioning of fault isolator complete with mounting base complete as required.

Supply, installation, testing and commissioning of addressable phone control module complete as required.

Supply, installation, testing and commissioning of Addressable Manual call point complete as required.

Supply and laying 2x15 sq.mm Fire survival armoured cable 600/1000V rated with annealed copper conductor having glass mica fire barrier tape covered by an extruded layer of cross linkable ethylene proplyene rubber insulation and LSZH inner bedding, steel wire armouring & LSZH outer sheath complete as required.

Providing and fixing PVC insulated copper conductor ISI marked armoured cable (IS:1554) 4 x 1.5 sq mm complete with neccessary saddling and clamping complete - as actual quantity measured. (From FACP Panel to Repeter Panel at Security - Legnth assumed)

Fire Fighting:- Providing, laying, testing & commissioning of 'B' class medium duty G.I. pipe conforming to IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade comolete as required :

Pendent Sprinkler

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISi marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required :

Supply and installation of CO2 – 4.5 Kg cylinder along with stand confirming to IS 15683 complete in all respects.

Single headed Gun Metal

Liasioning and will take necessary Statuary Approvals, NoCs, Advisory, Clearance etc. from all concern Local Authorities / Departments, if any, required before start of the work, during the work, after execution of work & before handing over.

Supplying and fixing Single headed external yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISi marked, conforming to IS 5290 (type A) with blank Gunmetal/Stainless Steel cap and chain as reauired :

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the followinq as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories :

2X4.0 sq. mm + 1X4.0 sq. mm Earth wire.

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line {Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes comolete as reauired.

2X2.5 sq. mm + 1X2.5 sq. mm Earth wire.

2X1.5 sq. mm + 1X1.5 sq. mm Earth wire.

Wiring for light point/fan point/exhaust fan point/call bell point with 1.5 sqmm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate,, suitable GI box and earthing the point with 1.5 sqmm FRLS PVC insulated copper conductor single core cable etc. as required.

Group C

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection, painting etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 15/16 & 5/6 amps modular socket outlet and 15/16 amps modular switch, connection, painting etc. as required.

Wiring for Submain/Circuit wiring alongwith earth wire with the following sizes of FRLS PVC insulated, copper conductor single core cable in surface/ recessed medium class PVC conduit as required.

6 way (4 + 18), Double door, horizontal type

Wiring for Twin control light point light with 1.5 sqmm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with 2 way modular switch, modular plate,, suitable GI box and earthing the point with 1.5 sqmm

FRLS PVC insulated copper conductor single core cable etc. as required.

POINTS

Supplying,installation,Testing and commissioning of Main and sub panels as per drawing and specifications. Panel should be dust and vermin proof (IP-52). Panel shall be fabricated from 14 /16 SWG CRCA sheet metal duly painted with seven tank process and poweder coated of approved paints. Panel consisting of following. Note : All MCCBs shall be Ics = 100 % Icu and to be adjustables. All MCB shall be 10kA - C-Curve, All ACBs shall be Icu=Ics=Icw for 1 Sec. MAIN PANEL (At 7th Floor Elect Rm) Incomer : 400 A FP MCCB, 35 kA, T/M - 1 No. incomer shall be inbuilt protection of S/C, O/C and E/F protection with SPD - 400 A, 440V, FP, Copper. Busbars(connections shall be done with bimetallic lugs) - 40 x 6 mm Copper Earth Busbars - CTs with MFM - indicating lamps Outgoing Feeders : - 250 A TPN MCCB, 25 kA, T/M (2 nos.) - 80 A FP MCCB, 25 kA, T/M (2 nos.) - 40 A FP MCB, 10 kA (10 nos.) - 6A - 32 A FP MCB, 10 kA (2 nos.)

4 way (4 + 12), Double door, horizontal type

8 way (4 + 24), Double door, horizontal type

4 way (4 + 12), Double door, horizontal type

Supplying and fixing following rating, double pole, (single phase and neutral) 240 volts, residual current circuit breaker (RCCB), having a sensivity current 30/100/300 miliampere(as per load) in the existing MCB DB complete with connections,testing and commissioning etc. as required :

15 mm thick lining

Supplying and fixing following way, Horizontal type three pole and neutral,prewired, sheet steel, MCB distribution board, 415 volts,on surface /recess, complete with tinned copper busbar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required (But without MCB / RCCB / Isolators).

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 5 amps. to 32 amps. rating, 240/415 volts `C' series, miniature circuit breaker (MCB)suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Single Pole

Supply and laying of following Hot deep G.I. Earth strip or copper earth strip for earthing with all required jointing / cutting / welding complete with all hardwares and all welded joints to be painted with black bitumin paints and to be wraped with jute complete to the satisfaction of E.I.C

40 x 6 mm GI earthing strip

Supply, laying, installing and commissioning of following size PVC insulated wire including end terminations with bimetallic type lugs as per the requiements with each piece of cable etc. complete for earthing duly clamped / laid in existing conduit / trunking cable tray etc complete

4.0 sq.mm in green colour

Supply, laying with excavation and backfilling of cable trench/tray as specified in General specification of Erection, Installation, Testing & commisioning of Electrical Equipments/ Cable route layout , termination , erection and testing of 1.1 KV Power FRLS XLPE Cables . Outdoor cable will be laid in buried cable trench and via HDPE duct laying and in Indoor application it will be in Cable trench by provision of Cable tray and supports inside the trench as per cable and Accessories.

3.5 C x 185 Sq.mm A2XFY Cable

4 C x 16 Sq.mm Cu 2XFY Cable

4 C x 4 Sq.mm Cu 2XWY Cable

40 x 6 mm GI earthing strip

Supply, laying, installing and commissioning of following size PVC insulated wire including end terminations with bimetallic type lugs as per the requiements with each piece of cable etc. complete for earthing duly clamped / laid in existing conduit / trunking cable tray etc complete

4.0 sq.mm in green colour

3.5 C x 185 Sq.mm A2XFY Cable

4 C x 2.5 Sq.mm Cu 2XWY Cable

3 C x 2.5 Sq.mm Cu 2XWY Cable

3 C x 1.5 Sq.mm Cu 2XWY Cable

Supplying and making end terminations with brass compression glands and aluminium/copper lugs for following size of PVC insulated and PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade as required.

3.5 x 185 sq.mm. Aluminium Cable

Supply, erection, fabrication and jointing of following size GI hot dip galvanized cable tray with cover and all accessories such as bends / cross / reducers / Tee, with covers or without covers and clamps, GI hardwares, other accessories etc. as per drawing and specification complete in line and level etc. complete to the satisfaction of EIC (Galvanisation thickness shall not been less than 75 micron)

100 x 25 x 2.0 mm Perforated cable tray with 110 x 10 x 2.0 mm plain GI hotdeep cover

150 x 50 x 2.0 mm Ladder type cable tray

Supply, erection, fabrication, cutting, welding and installation of structural steel using m.s. angles, flats, channels etc. as per drawing and specification with one coat of red-oxide paints and two coats of approved enamel paints with all hardwares such as anchor fastners, GI nutbolts and washers etc. complete to the satisfaction of EIC.

Supply and installation of 100 mm x 100 mm x 60 mm junction box as per drawing. Junction box duly fabricated from 16 SWG hot deep G.I. sheet with top cover of 16 SWG hot deep GI cover plate, neo-prene gasket inside, all required hardwares, necessary knock-out all sides suitable for 4 x 4 / 3 x 2.5 sq.mm Cu. YWY / 2XWY cables glanding complete with 15 A terminals inside the junction complete to be installed on wall / RCC / steel structure with necessary drilling / welding etc. complete to the satisfaction of EIC

Supplying, and fixing following thickness duly laminated of aluminium foil mat finish closed cell Nitrile rubber (class “O”) insulation on existing duct after applying suitable adhesive for nitrile rubber. The joints shall sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required. above values should have pressure rating of 25 bar minimum

Supply, installation, testing and commissioning of Addressable Manual call point complete as required.

Supply, Installation, testing and commissioning of following Light fixtures etc. Including supply and installation of flexible cords, ball sockets, down rods, hardwares etc. Excluding supply and fabrication of structural steel supports for industrial fixtures in plant bldgs. but inclusive of erection of fixtures with all necessary structural steel supports and to be welded or nut-bolting with all necessary fabrication and drilling etc.complete. (Structural steel supports shall measure and paid extra as per the item in this tender).

155 W, 20000 Lumens LED Flood light fixture complete with all assembly lamp, drivers etc.

12 W Recessed false ceiling mounted 1200 Lumens LED downlight fixture with necessay assembly lamp, drivers, diffuser etc complete

6 W Recessed false ceiling mounted 600 Lumens LED downlight fixture with necessay assembly lamp, drivers, diffuser etc complete

20W, 2200 Lumens, 1200 mm long LED batten light fixture surface mounted with in-built driver etc complete

Supply and Laying of 2 core x 1.5 sqmm pvc insulated copper conductor for communication and wired remote controller in PVC Conduit for VRF units

Supply and Laying of 3 core x 2.5 sqmm pvc insulated copper conductor cable for indoor units in PVC Conduit

Supply and Laying of 3 core x 4.0 sqmm pvc insulated copper conductor cable for indoor units in PVC Conduit

4core x 10sqmm pvc insulated copper conductor cable

4core x 16sqmm pvc insulated copper conductor cable

Supply and fixing of fololowing rating 30mA RCBO with waether proof box

LIASIONING :

scope of work a. Prepare and submission of application at Electrical Inspectorate. b. Approval of Drawings. c. Arrange for Ele. Inspector site inspection. d. Receipt of NOC and submit at MGVCL for further action. Liasoning work with MGVCL as per scope of work a. Registration of application. b. Arranging for technical feasibility site survey from M/s MGVCL c. Obtaining detailed estimate from M/s MGVCL. d. Arranging for payment of estimation and Execution of agreement with M/s MGVCL. e. Release of power on proposed place from M/s MGVCL EI complete in all respects.

HVAC WORKS

Supply, Installation, Testing and Commissioning of Top Discharge Variable Refrigerant Flow air-conditioning units with 100% Inverter type compressor, Heat-pump type, air cooled condenser with low noise fan having interconnected control wiring and refrigerant piping housed in compact housing duly powder coated of following capacities All compressors shall be inverter type. The condensing units shall be suitable to work on cooling as well as heating mode. The condensing units shall be suitable for operation on 415 ±10% volts, 50Hz, 3 phase AC power supply and complete with auto check function for connection error, auto address setting, etc. The outdoor units shall be low noise type. outdoor units shall be of following capacities: (min. BEE3)

Supply of VRV indoor air-c

onditioning unit of below mentioned capacity suitable to operate from 230+10% volt, 50 Hz, 1/3 phase power supply, with air-cooled evaporator with coil, fan, and fan motor, air-cooled condenser with thermetically sealed scroll/rotary type compressor condenser coil, propeller fans controls, control panel, drain pan. The charging of ref/oil if required shall be included in the cost. The Unit should be 3 Star rated (on the date of procurements the minimum EER value of the units should be as per BEE Standard) with suitable electrical starter, etc. of the following capacities.

Ductable Type (8.0 TR)

Supply, Installation, Testing and Commissioning of Wall Mounted Split type Indoor Unit along with necessary arrangement

Supply and Fixing of Drain Pump for Ductable and Hiwall Units

Supply of Wireless remote

Supply of Wired Remote

Supply and fixing of Y joints

Supply and fixing of ODU Joints

41.3 mm dia pipe insulated with 19 mm thick insulation

34.9 mm dia pipe insulated with 19 mm thick insulation

28.5 mm dia pipe insulated with 19 mm thick insulation

22.2 mm dia pipe insulated with 19 mm thick insulation

19.1 mm dia pipe insulated with 19 mm thick insulation

15.9 mm dia pipe insulated with 13 mm thick insulation

12.7 mm dia pipe insulated with 13 mm thick insulation

9.5 mm dia pipe insulated with 13 mm thick insulation

6.4 mm dia pipe insulated with 13 mm thick insulation

Supply and installation of 150 (w)x 100 (d) x1.6 (thickness) Ms perforated Cable Tray with cover for exposed Refrigerant copper piping.

Refrigerant R-410A to top up the system

Providing and fixing in position the following PVC Drain with all necessary fittings and joints. Quoted price shall be inclusive of 6 mm closed cell nitrile rubber pipe insulation.

40 mm dia drain pipe.

Refrigerant R-410A to top up the system

Providing and fixing in position the following PVC Drain with all necessary fittings and joints. Quoted price shall be inclusive of 6 mm closed cell nitrile rubber pipe insulation.

40 mm dia drain pipe.

32 mm dia drain pipe.

25 mm dia drain pipes.

Wall Chiselling/ Opening for Drain & CU Pipe

Supplying, installing, testing and commisioning of GI volume control Duct damper complete with neoprene rubber gaskets, nuts, bolts, screws, linkage flandes etc. as poer specifications.

Supplying & fixing of powder coated extruded aluminium Supply Air grill with volume control damper as per specifications.

Supplying & fixing of powder coated extruded aluminium Return Air Grill without damper complete as required.

Supplying & fixing of powder coated extruded aluminium Supply Air Diffuser with aluminium volume control dampers with anti smudge ring & removable core

Supplying & fixing of powder coated extruded aluminium Return Air Diffuser without aluminium volume control dampers with anti smudge ring & removable core

Supplying, installing, testing of thermal insulated Flexible Duct of following size flexible ducting of following sizes duly suported at regular interval as per site requirements etc. complete as required as per specifications.

200 mm dia

300 mm dia

Supply and Installation of Fabric Flexible Canvas Connection to be installed between all the indoor Units and the ducting to provide flexibility of movement

Supplying & fixing of powder coated extruded aluminium 300mm dia Supply Air Jet Nozzle

Supply and fixing of Collar damper for Jet Nozzle

Supply and fixing of Rectangular Collar damper

Supply, Fixing & Testing of open cell nitrile rubber acoustic insulation, with density 140-180 kg/cum. and having anti fungal & anti bacterial properties as per DIN EN ISO 846, MATHOD A&C. The insulation should have been tested for air erosion at air velocity of 10000 fpm in accordance to ASTM Standard C 1071-05. 20 mm thick for Ducts.