SPL REPAIR TO MT GARAGE BLDG NO P-46 AND PROVN OF PATHWAY, INTERLOCKING, HARD STANDING NEAR STATION MANDIR AND PROVN OF WALL BEHIND NEW CENTRAL MANDIR AND PROVN OF 06XTOILET AND BATHROOM AT BLDG P-97 AT BINNAGURI MIL STATION UNDER GE (S) BINNAGURI

Amount

Schedule 'A'

Taking down Chowkhats or frames exc. 1.5 sqm but not exe 4.00 sqm each but with shutters (without taking off shutters from the frames) complete all as specified and directred

Taking down Chowkhats or frames not exc. 1.5 sq. m each but with shutters (without taking off shutters from the frames) complete all as specified and directed.

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing rubbish off the premises complete all as specified and as directed

Taking down plaster on brick or stone wall, ceiling etc incl racking out joints hacking for keys scrubbing down with water etc. Complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for Complete all as specified and as directed.

Hacking out old broken unserviceable glass panes (any thickness, size, quality or description) for metal frame including punching or drilling out old glazing pins/spring clips.

Demolition of brick masonary work, built in cement mortar including all quions, arches, pillars, etc. but excluding precast concrete articles etc. and deposited where directed complete all as specified and directed.

Dismantling old PGI/CGI sheeting any gauge, thickness, including Nainital. Sikkim or similar pattern roof/facia etc complete all as specified and directed.

Demolation of un-reinforced cement Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. for receieving top layer complete all as specified and directed.

M& L for vetrified ceramic tiles 10 mm thick (square/rectangular) light shade, area of each tiles not exceeding 0.36 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete over 15mm thick screed bed in CM(1:6) complete all as specifierd and as directed.

M& L for vetrified ceramic tiles 10 mm thick (square/rectangular) light shade, area of each tiles not exceeding 0.36 sqm in skirting/dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match as in Vertical surface including 10 mm thick screed bed in cement mortor 1:4 complete all as specified and directed.

M&L for Machine cut kota stone slab flooring mirror finished 18-20mm thick (each slab not less than 0.25 sqm) over cement screed base rendering laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing and 20 mm thick screed bed or bedding layer in CM 1:4 surface finished fair and even for laying floor finishes complete all as specified and directed.

All as per item No- 14 here- in- above but as in skirting and on 10 mm tkick rendering/ back coating in CM (1:4) - ditto --

M&L for high tensile 550 MPA yield strength Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering The sheet shall have a hot dip metallic zinc aluminium alloy coating of zinc 43.5%, aluminium (55%)and silicon (1.5%) with total mass coating of 150 gms/sqm on both sides. Covered width will be 1020mm and sheet length as per site requirement. The profile is having return leg for proper side lap. The sheet shall be fixed using self drilling/self capping screws with EDPM seal complete all as specified and directed.

All as per item No- 16 here- in- above but Plain sheets as in ridges/ hips / valley/Eaves and Eaves board - ditto --

M&L for mild steel rolled sections conforming to Fe - 410 (Gde E-250) as in main and cross beams, hip and jack rafters; verticals , purlins where connected to common rafter and running rails and guides for sliding doors fixed with angle cleats or other connecting plates painting one shop of zinck chromimum pimer paint including preparation of surfaces at contractor workshop before fabrication complete all as specified and directed complete all as specified and directed.

M&L for MS flat iron bent to shape, holes drilled etc. complete as in wind ties etc including one coat of red oxide paint complete all as specified and directed.

S&F rolled mild Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment of grade Fe410W (Gde E-250) quality A complete all as specified and directed.

M&L for 75mm thick plain cement concrete 1:3:6 type C2 (using 40mm graded stone aggregate) as in path / steps laid with and including use and waste of form work and finishing the surface even and rough complete all as specified and as directed.

M&L for PCC 1:2:4 type B-0 using 12.5mm graded stone aggregate as in sub base flooring 25 mm thick surface finished even and rough to receive the topping layer completed all as specified and directed

M&L for 75mm thick plain cement concrete 1:3:6 type C2 (using 40mm graded stone aggregate) as in sub base of floor over and including 50 micron polythene film laid complete all as specified and as directed.

M & L PCC (1:3:6) type C1 (20mm graded aggregate) as in bed block for fillinghollow space of steel chowkhats, fixing of hold fast, coping, slightly rounded or chamfered on edges, finished even and smooth on exposed concrete surface without using extra cement all complete as specified and as directed.

M&L for broken stone or boulders hardcore of gauge not exceeeding 63mm, deposited , spread and levelled in layer ot exceeding 15cm thick, watered and rammed to a true surfaces completed all as specified and directed .

S&F of 3mm thick plain glass, ordinary quality and glazing with oil putty in square n.exc 0.5 sqm in each pane complete all as directed.

S&F 4mm thick non-Asbestos fibre cement building board( E-board) false ceiling with board of size 600x600mm with powder coated GI snap grid frame work including cutting holes in brick wall built in cement mortar & making good in cement concrete 1:2:4 type B0 Cement mortar 1:3 complete all as specified and directed including all necessary drilling and necessary arrangement to fix electrical items as under:- (a) 27x27x0.55mm thick GI angle powder coated duly plugged @ 600mm centre to centre along perimeter of wall. (b) 25x25x0.55mm thick GI tee powder coated as main and cross runners suspended with 1.6mm dia GI wire suspenders(n.exc 1.2mtr length) with adjustable clamps and dash true fastners plugging in RCC slab/A.I Runner of slopped roof placed @ 600mm centre to centre from perimeter of wall. (c) Fixing of 4mm thick non-Asbestos fibre cement building board( E-board) false ceiling with board of size 600x600mm of approved texture and finished complete with two coats of oil based distemper over a coat of alkali resistance primer on ceiling. NOTE: The complete ceiling work shall be done as per manufactures instruction and as directed.

S&F for pressed steel frames 125x60mm size for doors with one or more rebates including necessary lugs, hinges, lock strike plate, etc., complete all as specified and directed.

S&F 35mm thick second class hard wood rail and style Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

M&L second class Hard wood 35mm thick factory made Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, complete all as specified and directed.

S&F in repair factory made Z section steel window with side hung shutter frame including projecting/ box type hinge with steel handle and steel peg stay. complete without glazing bars , dovetailed or welded including a shop coat Red Oxide priming complete all as specified and directed.

S&F in repair factory made Z section steel window with side hung shutter frame including projecting/ box type hinge with steel handle and steel peg stay. complete with glazing bars , dovetailed or welded including a shop coat Red Oxide priming complete all as specified and directed.

S & F Mild steel work in framed work such as in gates,grills, Framed guard bars, gratings, ladders etc., with ends of bars shouldered and/ or riveted, or forged into spikes, and similar work confirming to Fe 290 Gde E-165.complete all as specified and directed.

M&L for brick work with old size sub class 'B' bricks, straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in cement morter 1:6 finished even and fair without using extra cement complete all as specified and as directed.

M&L for external rendering 20 mm thick in two layer, first layer shall be of 10 mm thick CM 1:6 and second layer of finishing coat shall be 10 mm thick in CM 1:4 mixed with WPC as per manufacturer instruction by weight of cement on brick work or concrete surfaces of wall and finished even and fair complete all as specified and directed. Note-WPC shall be measured and paid seperately.

Supply only integral water proofing compound conforming to IS: 2645 - 1975 specification complete all as specified and as directed.

M&L for prepartion of newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of cement based wall care putty all as specified and directed.

M&L for preparing of newly plastered surfaces of wall including cornices etc by brooming down applying two coats of antifungal exterior acrylic emulsion paint over a coat of acrylic primer complete all as specified and directed.

M&L for preparation of newly wooden surfaces of any description, over 10cm width or girth and applying Two coat of synthetic enamel paint over a coat of red oxide complete all as specified and directed

M&L for preparation of newly steel surfaces of any description, over 10cm width or girth and applying Two coat of synthetic enamel paint over a coat of red oxide complete all as specified and directed

M&L for applying two coats of oil bound distemper over a coat primer over a coat of cement based wall care putty including complete removal of existing treatment all as specified and directed.

S&F sliding door bolt of 250mm long plate Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F aluminium handle cast type anodiside of 150 mm size complete all as specied and directed.

S&F 150 mm long Aluminium anodised barrel tower bolts complete all as specified and directed.

S&F 300mm ordinary rat tail rod pattern spring including roller plate complete all as specified and directed.

S&F of 140mm floor door stopper of alluminium alloy body and tongue anodised with hard drawn steel spring fixed in door complete all as specified and directed.

S&F 100 mm stainless steel butt hinges etc complete all as specified and directed.

M&L for plain cement concrete 1:3:6 type C-2 (using 40 mm graded stone aggregate ) as in surface channels and drains etc complete all as specified and directed.

M&L for machine pressed ,pre-polished and chemically treated, smooth finished ,exterior graded coloured cement concrete Chequered tiles 30cm x 30cm x 22-25mm thick, set, jointed and pointed in neat cement slurry with gray cement and pigments in floors over and including 15mm thick screed bed or bedding layer in cement mortar 1:4 complete all as specified and directed.

Surface excavation n exc 30cm deep and average 15cm deep and getting out in soft/ loose soil complete all as specified and directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m depth and not exceeding 1.5 m depth in soft /loose soil etc complete all as specified and directed

Returning, filing in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in any type of soil etc complete all as specified and directed

Removal of excavated materials exceeding 250 m and n. exc. 500 m depositing where directed at a level not exceeding 1.5 m above the starting points etc complete all as specified and directed

Excavation over area 1.5m depth for foundation etc. in soft /loose soil etc complete all as specified and directed.

M&L for PCC 1:4:8 Type D2 using 40mm graded stone aggregate in foundations, filling and mass concrete complete all as specified and directed.

M&L for providing RCC (desigm mix) M-25 using 20mm graded stone aggregate as in Rafts, Footings,Foundation, plinth beams, Braces for columns etc complete all as specified and directed. (Note :- Reinforcements and formwork shall be measured and paid separately)

M&L for providing RCC (desigm mix) M-25 using 20mm graded stone aggregate as in column, pillers, piers, post and struts etc complete all as specified and directed. (Note :- Reinforcements and formwork shall be measured and paid separately)

M&L for providing RCC (desigm mix) M-25 using 20mm graded stone aggregate as in Beams,Cantilevers,Lintels etc and the like complete all as specified and directed. (Note :- Reinforcements and formwork shall be measured and paid separately)

M&L for providing RCC 1:2:4 type B-1( using 20mm graded stone aggregate) slab supported on walls, beam and column in floor, roof, landing, balconies, canopies, deck slab aand in shelves and the like inclluding necessary formwork complete all as specified and directed.

Form work to sides of column, pillers, piers, post and struts etc for flat rough finished concrete surface complete all as specified and directed.

Use and waste of form work to soffits of floor or roof beam , beam haunching, girders, bressummers, lintels, cantilevers, shelves, for flat rough finished surfaces complete all as specified and directed.

Form work to sides of concrete foundation ,footings, bases of columns, raft and raft beams sides and soffits (if any )of foundation and plinth beams for flat rough finished concrete surface complete all as specified and directed.

M&L for TMT bars 10 mm dia, cut to length, bent to shape required including cranking, bending spirally for hooping for columns and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L for TMT bars 5mm dia and over upto and including 10mm dia as in stirrups, spacers and binders , cut to length, bent to shape required including cranking, bending spirally for hooping for columns and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

S&F, factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain cover PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour PVC sheet for top rails lock rail and bottom rail on either side & as gap insert for top rail and bottom rail paneling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the styles and rails with suitable PVC sheet beading and jointed together with solvent cement and supply & fixing in the frame at site as per specification and shown on drawing SSR Part-II (2004) all as specified complete all as specified and directed.

S&F factory made Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet, reinforced with MS square tube, supplying and fixing in opening with fittings as per specification & drawing complete all as specified and directed.

S&F factory made Z section steel ventilator with top hung shutter frame including projecting/ box type hinge with steel handle and steel peg stay. complete with glazing bars , dovetailed or welded including a shop coat Red Oxide priming complete all as specified and directed.

M&L for rendering 5mm thick in CM 1:3 in ceiling finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of newly plastered surfaces of ceiling and applying three coat of white wash complete all as specified and diredted.

M&L for non skid coloured joint free ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exc. 0.11 Sqm but n. exc. 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match as in floor including 15mm thick screed bed in cement mortor 1:6 complete all as specified and directed.

M&L for glazed coloured ceramic tiles (450x350x7mm thick) on vertical surfaces such as skirting/dado set and jointed in neat cement slurry pointed in white or coloured cement to match over 15mm thick rendering in CM(1:4) complete all as specified and directed .

S&F of Figured glass, pin head type 4mm thick in squares n.exc 0.50 Sqm in each pane complete all as specified and as directed.

M&L for sand filling under floor or in foundations including watering and consolidation in layers n. exc 25 mm thick complete all as specified and directed

S&F vitreous china wash basin, white, flat back, size 550x400m excluding taps, waste , chain & plug & porcelain stopper including brackets incl cutting for pinning in ends of bracketes or erecting stand and fixing and supply and waste pipe complete all as specified and directed.

M&L for CI Nahani trap with grating including jointing to waste pipe fixed in cement concrete (1:2:4) type B1 (diameter of outlet 100mm) complete all as specied and directed.

S&F stop valve,fancy type chromium plated screwed down,high pressure with crutch or butterfly handle,screwed both end for iron pipe or for union of 15mm bore complete all as specified and directed.

S&F bib taps, fancy type chromium plated with crutch or butterfly hadle screwed down, screwed for iron pipe or brass ferule of 15mm bore complete all as specified and as directed.

S&F PVC flushing cistern symphonic action type,10 ltrs capacity,low level white with inlet ball valve,float and handle including bracket including flush pipe complete all as specified and as directed.

S&F Brass CP central hole basin mixer for WHB complete all as specified and directed.

S&F Brass CP mixer for mixing hot & cold water screwed down for iron pipeand fixed complete all as specified and directed.

S&F Tubular towel rail of brass chromium plated, 20mm dia, D type, 60cm long between flanges, fixed in repairs complete all as specified and directed.

S&F stainless steel shop dish best quality chromium plated brass complete all as specified and directed.

S&F of PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as specified and directed.

S&F of gratting doom 100mm size with waste hole complete all as specified and directed.

S & F for vitreous China squatting pan, 'Orissa' pattern, size 580 x 440 mm white with integral foot rest and 'P' or 'S' trap, including provision of lime concrete bedding, connection to trap and flushing pipe etc complete including making good to disturbed surfaces of floor to match with existing specifications as specified.

S&F 15mm bore Gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed all complete as specified and as directed.

S&F swivel shower roses of chromium plated with shower arm any colour for fixing with shower arm15mm pipe complete all as specified and directed.

S&F of PVC 110 mm bore (SWR) pipes single socket, in any length with rubber ring joint, laid in tranches or in floor, complete all as specified and as directed.

S&F of PVC (SWR) bend any radius suitable for 110mm bore PVC pipe jointed with solvent complete all as specified and directed.

S&F of PVC (SWR) vent cowl any radius suitable for 110mm bore PVC pipe jointed with solvent complete all as specified and directed.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc. and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed.

S& F 15 mm bore steel water tubes, medium grade, galvanised with all fitings and fixed to wall, complete all as specified and directed.

S& F 20 mm bore steel water tubes, medium grade, galvanised with all fitings and fixed to wall, complete all as specified and directed.

M&L for 100mm thick plain cement concrete 1:3:6 type C2 (using 40mm graded stone aggregate) as in sub base of floor over complete all as specified and as directed.

M&L for 80mm thick M-40 grade factory made vibratory compected cement concrete rubber moulded, interlocking paver block any shape and size conforming to IS 15658-2006 with grey cement and pigment as approved laid over and including 25mm thick consolidated sand cushion and joints filled with sand including demolition of old paver block complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in sub base flooring 50 mm thick surface finished even and rough to receive the topping layer completed all as specified and directed

M&L for Endura tiles of size 300x300x10mm set, jointed and pointed in neat cement slurry over in pavement/ footpath/ floor over including 15mm thick screed bed in cement mortor 1:6 complete all as specified and directed.

M&L preparing newly plastered or unplastered surface of wall and applying two coats of Cement base paint over a coat of cement base primer complete all as specified and directed.

INTERNAL ELECTRIFICATION Taking down carefully aluminium conductor point wiring (light,fan,socket or power) complete including fittings such as switches,ceiling roses, pendants, regulators ,sockets etc. and removing (except those to be reused shall be kept in safe custody at the site ) and making good disturbed surfaces of walls, floors etc.to match with the existing complete all as specified.

M&L point wiring complete with FRLS PVC insulated unsheathed multistranded copper conductor of size 1.50 sqmm nominal cross sectional area single core drawn in and including 20mm dia 'medium grade' PVC concealed conduits and fittings, including cutting chasingin brick wall n.exc 10cm width or girth(excluding ceiling surface), pressed steel concealed terminal switch boxes not less than 1.2mm thick of reqd size factory made duly painted inside and outside with two coats of black bituminous paint over one coat red oxide primer, 3mm thick plastic laminated sheet top cover (ISI Marked) fitted with chromium plated brass screws & washers complete including 1.50 sqmm nominal cross sectional area PVC insulated unsheathed multistranded copper conductor green as earth wire connected to earth dolly with all accessories including making good disturbed surfaces with CM(1:4) with treating the surfaces as per existing finishes complete all as specified and directed. (a) One light point controlled by one way switch 5/6 amps.

(b) One ceiling fan/Exhaut fan point controlled by one way switch 5/6 amps.

(c) One socket out let 5/6 amps point on the same board

(d) One socket out let 5/6 amps point on the independent board

All as per item No102 above but wiring with 2.5 sq mm single core copper conductor for one socket out let 15/16 amps point on the independent board complete all as specified and directed.

S&F switch piano flush type 5/6 amps single pole one way all as specified.

S&F socket 2 in 1, 5 Pin, 5/6 amps, white ivory finish flash type complete all as specified and directed.

S&F of socket outlet 2 in 1, 5 Pin 5/15 Amp multipurpose 230 volt flush type complete all as specified and directed by Engr-in-Charge.

S&F switch piano flush type 15/16 amps single pole one way complete all as specified and directed.

S&F ceiling rose, bakelite, surface type, 220/240 volts, three terminals complete all as specified and directed.

M & L for lamp holder, insulated body, with back plate suitable for batten/angle fittings complete all as specified and directed.

S & F deluxe fan Electronic regulator AC 50 Hzs rotary step white/ivory finish complete all as specified and directed.

S & F Wall mounted slim LED batten 20W, with extruded aluminium housing, with integrated LED driver complete all as specified and as directed.

S&F High Power LED street light fitting ,system wattage-35 Watt, made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having IP65 protection and impact resistance of IK07 with 10KV built in surge protection device using 2.5 Sqmm PVC insulated three core copper cable including taking down all as specified and directed.

Supply and Fixing MCB DB double door, powder coated sheet metal enclosure, 8 way 240 volts grade single pole and neutral with 200 amps rated bus bar,IP 43 protection fixed to wall using nuts & bolts and washer of suitable dia and grouted to wall using suitable gutties complete all as specified and as directed.

Supply and Fixing MCB DB double door, powder coated sheet metal enclosure, 4way 240 volts grade single pole and neutral with 200 amps rated bus bar,IP 43 protection fixed to wall using nuts & bolts and washer of suitable dia and grouted to wall using suitable gutties complete all as specified and as directed.

S&F MCB single pole & neutral 6 to 32 amp, 415 volts, 'C' series, 10 KA breaking capacity & making connection complete all as specified and directed.

S&F MCB single pole, 6 to 32 amps rating, 240 volts, 'C' series, 10 KA breaking capacity & making connection complete all as specified and directed.

M&L for Earthing complete with galvanised steel plate electrode of size 600x600x6.30mm thick burried directly in ground with earth pit not less than 2.25 meter deep below normal ground level with top edge of plate not less than 1.5 meter below normal ground level connected to galvanised 4 mm dia earth lead by means of nuts bolts check nuts GI washers earth wire protected by galvanised iron pipe 15mm bore (Light grade) for building LT wall panel all as directed including concrete pit in PCC (1:3:6) type CI, precast RCC cover slab of size 30x30x10 cm with one handle for lifting made out of 8 mm diameter MS bar finnel wire mesh 20 mm bore galvanised iron pipe (medium grade) for watering charcoal or coke and salt in alternate layers necessary earth work in soft/loose soilwith and including taking down the old one complete all as shown in electrical plate No 3 of SSR Part I 2009 including testing on completion all as specified and directed.

S&F street light bracket, made out of GI pipe medium grade) 32mm bore, 1.2 m long bend to shape and fixing/grouting with wall using 2 Nos 25 x 5 mm size MS FI clamps with bolts, nuts & washers complete including drilling as necessary and two coats of Aluminium paint over a coat of Red oxide primer all as specified & directed.

S&F PVC Insulated screened XLPE Insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of of size 10 sqmm 2 core , providing lugs, straight through joints as required complete including jointing material as required and making connection of LT cables , including dismantling & taking out defective LT under ground PVC cable from trenches, cutting and removing defective parts complete all as specified and directed.:- Note:- Excavation & earthwork,sand cushoining,brick protection & GI pipe shall measured and paid separately,

M & L for sand cushioning with river Sand to underground cable (8 cm thick before laying and 15 cm thick after laying the cable punned to a thickness of 18 cm) complete all as specified and directed

Supply and laying sub class 'B' bricks laid dry and flat across the length of cable for protection of cable complete all as specified and directed

M&L for GI tubing 40 mm bore ,light grade with all necessary fittings laid in trenches/under road crossing/fixed on pole/wall/under floor including suitable mild steel FI clamps of required size complete all as specified and directed.

Takind down ceiling fan after removing all connection from wire and refixe at same position with all connection complete all as specified and directed.

S&F exhaust fan of 300mm sweep A/C single phase 230/240 volts heavy duty complete with fan motor, blade, bracket and ring including grouting anchor bolts and making good to disturbed surfaces to match the existing complete including provision of PVC insulated & PVC sheathed round flexible cable of copper conductor,Three core of size 0.5 sqmm from ceiling rose to connector of fan, surface of the wall shall be made good by cement work/plastering and matching by existing colour ,all the metal part shall be painted two coats of synthetic enamel paint over a coat of primer, writting the MES no. with white colour paint complete all as specified and directed.

S&F sub main wiring with single core FRLS PVC insulated unsheathed multistranded copper conductor conforming to IS 694 of size 4sqmm nominal cross sectional area,1100 v grade and two run of 4sqmm nominal cross sectional area FRLS PVC insulated unsheathed multistranded copper conductor green colour as continuous earth wire drawn in and including 25mm dia 'medium grade' PVC concealed conduits and fittings,complete all as specified and directed. NOTE:- One unit length shall measured as two run of main wire and one run of conduit & earth wire.

M/s. RAMPHAL GARG

S. G. CONSTRUCTION

BBKundu

samrat saw mill and joinery workshop