Supply of Lab Equipment for CEIL Civil Lab, Bina(M.P.)

SIEVE SHAKER-GYRATORY-FOR 20/30 & 45CM DIA SIEVES WITH DIGITAL TIMER, Sieve Shaker Carries upto 7 sieves of 450mm diameter in single adaptor. Supplied without sieves or Lid‑Pan. Detailed specification as follows: Calibration from NABL Lab shall be included

SIEVE SHAKER-GYRATORY-FOR 20 & 30CM DIA SIEVES WITH DIGITAL TIMER- Sieve Shaker Carries upto 7 sieves of 200 / 300 mm diameter in single adaptor. Supplied without sieves or Lid‑Pan. Detailed specification as follows: Calibration from NABL Lab shall be included

SIEVE SHAKER-GYRATORY-FOR 20CM DIA SIEVES WITH DIGITAL TIMER Sieve Shaker Carries upto 7 sieves of 200mm diameter in single adaptor. Supplied without sieves or Lid‑Pan. Detailed specification as follows: Calibration from NABL Lab shall be included

PAVEMENT CORE DRILLING MACHINE WITH PETROL ENGINE - 5.5 HP AND 100MM DIA CORE DRILL BIT The machine is primarily intended to drill out core samples from the Asphalt or concrete road, Suitable for vertical drilling only. Detailed specification as mention in following page. Supplied with 100 mm dia X 450 mm / 400 mm Core drill bit.

CORE DRILL BIT 65 MM, 70 MM , 100MM and 150 MM DIA X 450MM WITH BARREL - V, With Portable Pump / Portable Submersible Pump

CORE CUTTING MACHINE - 150 MM DIA CORE -WITH ACCESSORIES Rock/stone/Concrete cube or cylinder cutting and grinding machine, with 450mm dia Diamond impregnated cutting wheel, suitable to cut up to 150mm depth. Equipped with 2 HP Three Phase Electric motor, starter. Floor standing model. Water Tank of 25 ltr. below machine level.

BITUMEN EXTRACTOR - MOTORISED WITH VARIABLE SPEED WITH DIGITAL RPM INDICATOR SPECIAL MODEL WITH AC MOTOR AND DRIVE : This model facilitates precise speed control and vibration free smooth operation. Speed variation up to 3600 RPM. Complies with following International Standards - ASTM D 2172, AASHTO T 58, T 164. Calibration from NABL Lab shall be included

BUOYANCY BALANCE WITH ELECTRONIC BALANCE - 15 KG X 0.1 GM For Water absorption and specific gravity test of aggregates. With Density basket, water tight cylinder and electronic balance of 15 kg x 0.1 gm sensitivity. The balance will be with under hook weighing arrangement and will be mounted on suitable table to facilitate the test. The Water tight container will be mounted on a mechanical jack, which will facilitate the up‑down movement of the container for weight in air and water. As per EN 12390-7, BS 1881:114, IS:2386 (Part III) Calibration from NABL Lab shall be included

REBAR LOCATOR - PROFOMETER PM8000 Profometer PM8000 - Portable Concrete Rebar locator - the latest generation 2023 product release by Screening Eagle Switzerland, under its value brand Proceq, is the most powerful & precise instrument for inspection of concrete for locating reinforcement bars, their Position, Spacing, Cover & Diameter of rebar, fully wireless designed for use in rough environments. Profometer PM 8000 with I Pad – Basic Model

REACTION CONTAINER - IS 2386 (PART VII), As per IS:2386 -Part VII (fig.5), Made of stainless steel, 50 to 75 ml. capacity, fitted with air tight cover.

REFRACTORY FURNACE-9" X 4" X 4"-1200°C, Light weight with ceramic wool insulation. The outer casing made of thick mild steel sheets painted attractively. Heating Chamber consist of grooved refractory bricks in which heating elements are inserted in coil form and are easily replaceable. Temperature controlled by Dual display microprocessor based Digital temperature indicator cum controller with K type sensor. compensating cable etc.working on 230 V. Max. Temperature: 1200 °C. & Working Temp.: 1150 °C. Detailed specification as follows: Calibration from NABL Lab shall be included

CHLORIDE METER FOR FRESH CONCRETE – (Germann Instrument make) The chloride meter has the best performance to quickly and accurately measure the chloride ion concentration contained in raw concrete/aggregate. All equipment required for measurement, such as standard calibration solution, cleaning solution, and sensor, are stored in the case, making it convenient to carry and use. From calibration to measurement and output, it is conducted in an interactive manner, making it easy for anyone to operate. In addition, it uses a large 128×64 LCD that cannot be found in existing chloride ion meters, so that the measurement results can be checked in real time during calibration or measurement, and the self-diagnosis function in the CPU checks the device status in real time and is configured to notify the user immediately if an abnormality occurs.

CALCIUM OXIDE POWDER - EXTRAPURE - 500 GM, Price per 500 gm.

FERRIC OXIDE RED EXTRAPURE-500 GM

MAGNESIUM OXIDE LIGHT - LR 500 - GM

SODIUM SULPHATE - 500 GM, Sodium sulfate anhydrous EM 500 G

CUBE MOULD-15 CM-ISI MARKED IS:10086. Weight of the mould will be about 13.5 kg. Strictly as per BIS specifications and within required tolerance. Calibration from NABL Lab shall be included

CUBE MOULDS-7.06 CM-ISI MARKED (FOR CEMENT) As per IS:10080. The total weight of the Mould shall be 2.8 ± 0.2 Kg. Calibration from NABL Lab shall be included

PH METER-TABLE TOP-(0.01 PH)-(MTC)-(MANUAL CALIBRATION)-(PM 100) Digital pH Meter, Detailed Specifications as mentioned in the following page.

TDS METER-TABLE - DIGITAL TDS METER Microprocessor based Six Ranges: 0.001 PPM to 200 PPT. 4 digit LED display. Table top model. Accessories (Unbreakable Cell EQ- 708A, stand set, screw driver).

HIGH PRECISION ELECTRONIC BALANCE-210 GM-0.001 GM (1 MG)- EXTERNAL CALIBRATION Capacity : 220 gm, Resolution : 0.001g, Repeatability : ± 0.001, Linearity : ± 0.0015, Response Time : < 3 Second, Pan Size : 110 mm Dia., Calibration : External, Technology : Monolithic Block Technology. Calibration from NABL Lab shall be included

ANALYTICAL ELECTRONIC BALANCE -(220 GM X 0.0001 GM/0.1 MG)- EXTERNAL CALIBRATION 0.1 mg Accuracy. Detailed specification as follows: Calibration from NABL Lab shall be included

BRINELL HARDNESS TESTING MACHINE - MOTORIZED Brinell hardness tester is precision engineered to IS:2281-1968, BS:240 and ASTM:E10 Most suitable for production testing. These machines are designed to measure hardness of casting, forgings, other metals and alloys of all kinds, hard or soft, whether flat, round or irregular in shape. Supplied with standard accessories. For details, please refer description

IZOD IMPACT TESTING MACHINE- ASTM-A370 :2020 - DIGITAL Impact Testing Machine is suitable for testing raw material specimen as well as finished components. According to ASTM A 370:2020 And IS 1598:1977 With Recommended Accessories · U NOTCH GAUGE - FOR IZOD · IMPACT TESTING MACHINE · V NOTCH GAUGE - FOR IZOD · IMPACT TESTING MACHINE · U NOTCH MILLING CUTTER · V NOTCH MILLING CUTTER · CALIPER GAUGE - FOR IZOD IMPACT TESTING MACHINE · SELF CENTERING TONG - FOR IZODIMPACT TESTING MACHINE · DEPTH NOTCH GAUGE - FOR IZODIMPACT TESTING MACHINE · TEMPLATE - FOR IZOD IMPACT TESTING MACHINE · DIGITAL SUB ZERO TEMP BATH · CHARPY NOTCH BROACHING MACHINE - ASTM A370 - MOTORIZED-

BELT GRINDER (POLISHER) - CE MARKED- For flat, Coarse grinding prior to fine grinding. The specimens to be ground in 60, 80 or 120 grit after cutting operation or moulding to remove surface imperfections. Useful step to remove light metallurgical damage in the specimen surface induced during cut-off operation.

PROFILE PROJECTOR RPP-250C (FOR CHARPY SPECIMEN INSPECTION)

NOTCH BROACHING MACHINE - MANUAL - FOR IMPACT TEST Detailed Specification as below. Accessories 1. U NOTCH BROACHING TOOL – ASTM A370 2. V NOTCH BROACHING TOOL – ASTM A 370

ABRASIVE CUT-OFF MACHINE RACM-55 Detailed Specification as follows:

Micrometer (LC 0.01 mm) (Mitutoyo / Micro/ Baker Make)

Humidity Chamber

Measuring Cylinder (100ml, 150 ml and 300 ml)

Intalation and Transportation Charges