Maintenance, Repairing, Renovation work for Different Municipal Bunglows, Municipal Schools, Municipal Schools, Anganwadi, Municipal Library, & Municipal Garden and Other Municipal Buildings in Navrangpura ward at West Zone.

1. Name of Work : Maintenance, Repairing, Renovation work for Different

Municipal Bunglows, Municipal Schools, Municipal Schools,

Anganwadi, Municipal Library, & Municipal Garden and Other

Municipal Buildings in Navrangpura ward at West Zone.

2. Tender Estimated Cost : Rs:-

: 1% of the Tender Cost in the form of Rs. 99,995.00 (D.D. / Pay

3. Earnest Money

- Order / Local Micr Check/B.G.)

4 Tender Fee Rs : Demand Draft of Rs.2400.00

5 S.D. : 5 % of tender amount

6. Time-Limit : 12 months

7. Validity Period : 120 Days

(a) Eligibility Criteria Register “D” class in PWD in Govt. R&B/CPWD/AMC or

equivalent registration with any other state Govt. or

8. (i) Last Date of Submission of :

(ii) Mode of Sending : a) In Sealed cover in duplicate copies by Registered Post A.D,

or by Courier.or hand delivery

b) Tender sent by ordinary post will be rejected out right.

(iii) Description essential to :

a) Name of work, Tender Notice No. & Tender No.

be made on sealed cover b) Date of receiving tender by Corporations.

(iv) Mode of quoting rates in : The Price bid shall be submitted online only.

Schedule of Quantities and

Rates It shall not be submitted Physically.

9. Date of Opening : Dt.06-01-2026, 15:00 PM

10 Place of Submission & : Submission of EMD. Tender fee and other Documents during office

Opening of Tender hours: On date.06-01-2026 &12:00 pm West Zone, 2nd Floor, A.M.

Office, Dr. Ramanbhai Patel Bhavan, Usmanpura.Ahmedabad

Municipal Corporation, W.Z. Office, Ahmedabad-380013.

11 Penalty Due to Delay of work (1) Rs.1000/- per day (for tenders amounting upto 10 Lakhs), (2)

Rs.2500 per day (for tenders amounting above 10 Lakhs and upto

30 Lakhs), (3) Rs.5000 per day (for all tenders amounting above

Lakhs) but not more then 10% of bill

Defect Liability : As per ‘B-1 Form Close

Whenever a work is allotted by Engineering staff, whether minor or

major of part thereof of any amount, the contractor shall be bound to

start the works within 48 hours of intimation of work. Communication

done telephonically via SMS, Via Whatsapp and through letter / E-

mail shall be considered legal and binding for the same. Failure of

comply to start the works in 48 hours of intimation as above by

Time permitted to start parts

contractor the contractor shall be levied penalty of (1) Rs.1000/- per

day (for tenders amounting upto 10 Lakhs), (2) Rs.2500 per day (for

tenders amounting above 10 Lakhs and upto 30 Lakhs), (3)

Rs.5000 per day (for all tenders amounting above 30 Lakhs). Three

times failures by contractor shall make contractor responsible to be

black listed unless and otherwise justified properly in writing /

binding within 15 days of last notice of penalty.

 The staff of the contractor shall wear safety jackets,

hoes, helmets etc. while on duty and any violation will attract

fine of Rs. 5,000/- for each incident.

Safety Failure to erect safety signage or trying to carry out he

works without proper precautions/safety measures as

equired will attract a fine of Rs. 5,000/- for each incident.

The contractor shall be responsible to make good and remedy at

his own expense any defect which may develop or may be noticed

before the period mentioned hereunder from the certified date of

completion, The within 15 days of receipt of the notice. In the case

of failure on the part of the contractor, the Engineer-in-charge may

rectify or remove or re-execute the work at the risk & cost of the

contractor. The Engineer-in-charge shall be entitled to appropriate

Defect &Liability Period the whole or any part of the amount of security deposit towards

14 the expenses, if any, Incurred by him in rectification, removal or re-

execution. The Defects Liability period shall be as under(a) for all

works costing upto Rs. 50,000 ( amount put to tender), the period

shall be 3 months from the certified date of completion.

(b) for all works costing more than Rs. 50,000 and upto Rs. 1 crore

(amount put tender), the period shall be 6 months from the

certified date of completion or one monsoon, whichever is later.

(c) for major projects costing more than Rs. 1 crore, the period

shall be 12 months from the certified date of completion which

should include one monsoon.

(d) For building works, the period specified in (a), (b) or (c) above

OR elapse of monsoon period following the certified date of

completion, whichever is later. For the purpose of deciding the

monsoon period, the 30th September may be treated as the last

Compensation for Delay 10% of Remaining work (As per Circular)

Whenever a work is allotted by Engineering staff, whether minor

or major of part thereof of any amount, the contractor shall be

bound to start the works within 48 hours of intimation of work.

Communication done telephonically via SMS, Via Whatsapp and

through letter / E-mail shall be considered legal and binding for

the same. Failure of comply to start the works in 48 hours of

Time permitted to start parts intimation as above by contractor the contractor shall be levied

16 of work penalty of (1) Rs.1000/- per day (for tenders amounting upto

Lakhs), (2) Rs.2500 per day (for tenders amounting above

Lakhs and upto 30 Lakhs), (3) Rs.5000 per day (for all tenders

amounting above 30 Lakhs). Three times failures by contractor

shall make contractor responsible to be black listed unless and

otherwise justified properly in writing / binding within 15 days of

last notice of penalty.

Addendum/Corrigendum If any Shall be Published 48 Hrs. Price To

the Final Submission Time And Date. The Same Shall From a part Of

Addendum/Corrigendum

17 Tender And The Same As to be Attached Along With The Tender

EPF Act As per Acoount Department circular no-37 Date:09/08/2018

GST will be paid extra by AMC/Authority at prevailing rate to the

Signature of contractor

Add. City Engg.(West Zone)

Name : Ahmedabad Municipal Corporation

Company's Seal :Date :

AHMEDABAD MUNICIPAL CORPORATION

ENGINEERING DEPARTMENT-WEST ZONE

Name of The Work:- Maintenance, Repairing, Renovation work for Different Municipal Bunglows, Municipal

Schools, Municipal Schools, Anganwadi, Municipal Library, & Municipal Garden and Other Municipal

Buildings in Navrangpura ward at West Zone.

Sr. No. Qty Description of Item Per Amount Rs.

Excavation for foundation up to1.5 m depth

including sorting out and stacking of useful

materials and disposing of theexcavated 115.92

stuff upto 50 Meter lead.(A) Loose or soft soil

1.5 to 3.0 mt.depth

Excavation for foundation for depth from 3.0 m to

5.0 m including sorting out and stacking of useful

c 50.00 materials and disposing off Cmt

the excavated stuff upto 50 Meter lead.(A) Loose

Excavation for foundation for depth from 1.5 m

to 3.0 m including sorting out and stacking of

useful materials and disposing off the excavated 270.83

stuff upto 50 Meter lead.(C) Hard Murrum

Filling available excavated earth (excluding

rock) in trenches, plinth, sides of foundations

2 50.00 etc. in layers not exceeding 20 cm. in Cmt

depth consolidation each deposited layer by

ramming and watering.

Filling in plinth with sand underfloors

3 50.00 including watering ramming, consolidating and Cmt

dressing etc. complete.

Filling in foundation and plinth with murrum or

selected soil in layers of 20 cm. thickness

including watering, ramming and 286.20

consolidating etc.

Providing and laying cement

concrete1:5:10 (1-Cement: 5- coarses

sand and:10-hand broken stone aggregates

40mm nominal size) and curing 2,492.51

complete excluding cost of formworkin (A)

Foundation and Plinth (upto 10 ton).

Providing and laying cement

concrete1:4:8 (1-Cement: 4- coarses

and:8-hand broken stone aggregates 40mm

nominal size) and curing complete 2,634.11

excluding cost of formworkin (A) Foundation

and Plinth (upto 10 ton).

Providing and laying cement concrete 1:3:6 (1-

Cement : 3- coarse sand : 6- hand broken stone

7 20.00 aggregates 40 mmnominal size) and curing Cmt

complete excluding cost of formwork in (A)

Foundation and Plinth..

Providing and laying cement concrete

1:3:6 (1-Cement:3-coarse sand:6-hand

broken stone aggregates 20mm nominal

size) and curing complete including cost of 4,006.15

formwork in (A) wall caps/coping (upto

Providing and laying cement concrete

work 1:2:4 ((1-Cement:2- coarse sand:4-graded

9 aggregates 20mm nominal size) curing

complete excluding cost of formwork

and reinforcement.

Foundations, footings, base or columns

and mass concrete 3,923.53

Slabs, landing, shelves, balconies, lintels,

b 20.00 beams, girders and cantilivers upto floor Cmt

Independent piers, columns, and pillars, upto

floor two level 4,012.47

Provdg. & laying cement concrete 1:2:4 (1

cement : 2 coarse sand : 4 graded stone

aggregates 20 mm nominal size) for

reinforced concrete chhajjas not exceeding

10 cm. thickness upto floors two level

including finishing the exposed surfaces 6,487.07

with cement mortar 1:3 (1 cement : 3 find

sand) to give a smooth and even surface

centering and form work and curing

complete excluding cost of reinforcement.

Providing and laying controlled cement concrete

M.150 for curing complete excluding cost of

formwork and reinforcement for reinforced

concrete work in (A) Foundations, footings,Base 3,871.39

columns and Mass concrete

Providing and laying in position Ready

Mixed M-150 grade concrete for

reinforced cement conctere work, using

cement content as per approved Design Mix

manufactured in fully automatic

batching plant and transported to site of work

intransit mixer for a lead up to 10 kms

having continuous agitated mixer,

manufactured as per mix design of specified

grade for reinforced cement concrete work

11A 15.00 including pumping of R.M.C. from transit Cmt

mixer to site of laying, excluding the cost of

centering shuttering finishing and

reinforcement including cost of admixtures

inrecommended proportions as per IS:9103

to accelerate/ retard setting of concrete,

improve work ability without impairing

strength and durability as per direction of

theEngineer-in-charge. Without Fly Ash (Min

cement level as per latest IS456 shall be

Providing and laying in position Ready

Mixed M-200 grade concrete for

reinforced cement conctere work, using

cement content as per approved Design Mix

manufactured in fully automatic

batching plant and transported to site of work

intransit mixer for a lead up to 10 kms

having continuous agitated mixer,

manufactured as per mix design of specified

grade for reinforced cement concrete work

12 15.00 including pumping of R.M.C. from transit Cmt

mixer to site of laying, excluding the cost of

centering shuttering finishing and

reinforcement including cost of admixtures

in recommended proportions as per IS:9103

to accelerate/ retard setting of concrete,

improve work ability without impairing

strength and durability as per direction of

theEngineer-in-charge. Without Fly Ash (Min

cement level as per latest IS456 shall be

Providing and laying controlled cement concrete

M.200for curing complete excluding cost of

formwork and reinforcement for reinforced

concrete work in (A) Foundations, footings,Base 3,977.88

columns and Mass concrete

Walls, from top of foundation level upto floor two

Slabs,landing,shelves,Balconies Lintels, Beams,

c 10.00 Girders and Cantilever upto floor two level. Cum

Columns, Pillars posts and struts upto floor two

d 5.00 level. Cum

Staircases excluding landing upto floor two level

Vertical and Horizontial its upto floor two level.

Providing and laying in position Ready

Mixed M-250 grade concrete for

reinforced cement conctere work, using

cement content as per approved Design Mix

manufactured in fully automatic

batching plant and transported to site of work

intransit mixer for a lead up to 10 kms

having continuous agitated mixer,

manufactured as per mix design of specified

grade for reinforced cement concrete work

13 25.00 including pumping of R.M.C. from transit Cmt

mixer to site of laying, excluding the cost of

centering shuttering finishing and

reinforcement including cost of admixtures

in recommended proportions as per IS:9103

to accelerate/ retard setting of concrete,

improve work ability without impairing

strength and durability as per direction of

theEngineer-in-charge. Without Fly Ash (Min

cement level as per latest IS456 shall be

maintained) (Cement level 450 kg )

Providing and laying controlled cement concrete

M.250 and curing complete excluding the cost of

formwork and reinforcement for reinforced

concrete work in

Foundations, footings, Base of columns and

B 5.00 Mass concrete. Cu.M.

Walls, from top of foundation

C 5.00 level upto floor two leve Cu.M.

Slabs,landing,shelves,Balconies, Lintels, Beams,

D 5.00 Girders and Cantilever upto floor two level. Cu.M.

Columns, Pillars posts and

E 5.00 struts, upto floor two level. Cu.M.

Providing and laying in position Ready Mixed M-

300 grade concrete for reinforced cement

conctere work , using cement content as per

approved Design Mix manufactured in fully

automatic batching plant and transported to site

of work in transit mixer for a lead up to 10 kms

having continuous agitated mixer, manufactured

as per mix design of specified grade for

reinforced cement concrete work including

14 5.00 pumping of R.M.C. from transit mixer to site of Cum

laying, excluding the cost of centering shuttering

finishing and reinforcement including cost of

admixtures in recommended proportions as per

IS: 9103 to accelerate/ retard setting of

concrete, improve workability without impairing

strength and durability as per direction of the

Engineer - in - charge. Without Fly Ash (Min

cement level as per latest IS

shall be maintained)

Providing and laying in position Ready Mixed M-

350 grade concrete for reinforced cement

conctere work , using cement content as per

approved Design Mix manufactured in fully

automatic batching plant and transported to site

of work in transit mixer for a lead up to 10 kms

having continuous agitated mixer, manufactured

as per mix design of specified grade for

reinforced cement concrete work including

15 2.00 pumping of R.M.C. from transit mixer to site of Cum

laying, excluding the cost of centering shuttering

finishing and reinforcement including cost of

admixtures in recommended proportions as per

IS: 9103 to accelerate/ retard setting of

concrete, improve workability without impairing

strength and durability as per direction of the

Engineer - in - charge. Without Fly Ash(Min

cement level as per latest IS

shall be maintained)

Providing and Laying ordinary cement

concrete 1:2:4 (1-Cement 2-coarsesand: 4-

graded stone aggregates 20 mm nominal

size) and finishing smooth with curing etc.

complete including the cost of form work but 8,341.79

excluding the cost of reinforsement for R.C.C

work in (iv) Slabs having more than 13 cm and

upto 15 cm.thickness

Providing and Laying ordinary cement

concrete 1:2:4 (1-Cement 2-coarsesand: 4-

graded stone aggregates 20 mm nominal

size) and finishing smooth with curing etc. 7,380.23

complete including the cost of form work but

excluding the cost of reinforsement for R.C.C

work in (iv) Slabs having more than 8 cm and

upto 10 cm.thickness

Providing and laying ordinary cement concrete

1:2:4 (1- Cement 2- coarse sand : 4- graded

stone aggregates 20 mm nominal size) for R.C.C

lintel including finishing smooth with,curing etc. 8,634.45

complete including the cost of formwork but

excluding the cost of reinforcement.

Brick work using common burnt clay

building bricks having crushing strength

16 not less than 35kg./Sq.Cm.in foundation

and plinth in Cement Mortar1:5 (1-Cement

:5 - fine sand)

(A) Conventional (upto 10 ton)

Extra Rate for brickwork in Above Item for

17 super structure above plinth level upto floor

two level (B) Conventional

(A) Conventional (upto 10 ton)

C) above floor two level Item No. 2(6.13) (A) Per

c 10.00 Modular Floor Per

D) above floor two level Item No. 2(6.13) (B) Per

d 10.00 Conventional Floor Per

Half brick masonry in common brunt clay

building bricks having crushing strength not

less than 35 Kg/Sq.Cm. in Cement mortar 1:4 (

1-Cement : 4 coarse sand ) in foundation 593.90

and Plinth conventional brickwork (up

to 10 ton) (B) Conventional

Extra for half brick masonry in super

19 10.00 structure above plinth level upto floor Smt

two level (B) conventional

Providing and laying Pre cast Light weight

concrete hollow core wall with hollow core

concrete unit of approved make & size of

mm thick, 600 mm wide and 2400 mm/

20 4.00 mm/ 2850 mm/ 3000 mm/ 3300 mm in legth Sqm

made from of controlled cement concrete

M20 having cube compressive strength not less

than 20 MP a jointing with high strength &

tensile adhesion non-shrink cementitious

joint compound /P.U. Foam. (Plaster not

Providing and laying Pre cast Light weight

concrete hollow core wall with hollow core

concrete unit of approved make & size of

mm thick, 600 mm wide and 2400 mm/

mm/ 2850 mm/ 3000 mm/ 3300 mm in legth

21 2.00 made from of controlled cement concrete Sqm

M20 having cube compressive strength not less

than 20MP a jointing with high strength &

tensile adhesion non-shrink cementitious

joint compound/ P.U.Foam. (Plaster not

Providing and laying Pre cast Regular

concrete hollow core wall with hollow core

concrete unit of approved make & size of

mm thick, 600 mm wide and 2400 mm/

mm/ 2850 mm/ 3000 mm/ 3300 mm in legth

22 4.00 made from of controlled cement concrete Sqm

M35 having cube compressive strength not less

than 35 MP a jointing with high strength &

tensile adhesion non-shrink cementitious

joint compound/ P.U.Foam. (Plaster not

Providing and laying Precast Regular

concrete hollow core wall with hollow core

concrete unit of approved make & size of

mm thick, 600 mm wide and 2400 mm/

mm/ 2850 mm/ 3000 mm/ 3300 mm in legth

23 4.00 made from of controlled cement concrete Sqm

M35 having cube compressive strength not less

than 35 MP a jointing with high strength &

tensile adhesion non-shrink cementitious

joint compound /P.U.Foam. (Plaster not

Providing form work in ordinary timber

planking so as to give a rough finish

including centering, shuttering, strutting and

propping etc. height of propping and

centering below supporting floor to celling not

exceeding 4 M & removal of the same for

in situ reinforced or plain concrete work upto

floor four level

Foundation, footings, bases of columns

etc. and mass concrete. 171.68

(B) Flat surfaces such as soffits of supspened

b 2.00 floors slabs Landings and the like. (1) Floors etc. Smt

upto 200 mm in thickness.

(B) Flat surfaces such as soffits of suspended

c 2.00 floor roof slabs Landings and the like. (2) Floors Smt

etc. above 200mm in thickness.

Vertical surface such as walls (any thickness)

d 2.00 partitions and the like including attached Smt

buttresses & string course & the like.

(ii) Sides And Soffits Of Beam, Haunchings

e 2.00 Cantilevers, Girders, Bressumers And Smt

Lintels Not Exceeding 1 M In Depth.

(G) Columns PillarsPosts and struts. (1) Square

Rectangular Polygonal in plan. 297.68

(2) Circular or curved in plan.

(H) (2) Sides and soffits of Beams Beam

h 2.00 Haunchings canti-levers Girders Bressumers Smt

and Lintels exceeding 1M.in Depth.

Providing and fixing 35 mm thick shutters for

Doors, windows and clear story windows

including anodised alluminium butt hinges

with necessary screws.

(A) Indian Teak Wood (ii) Fully Glazed.

(B) Indian Teak Wood (ii) Fully Panelled

(C) Indian Teak Wood (iii) Partly panelled

and partly glazed. 5,133.69

Providing and fixing 35 mm thick shutters for

Doors, windows and clear story windows

including black enamelled M.S.butt hinges

with necessary screws.

(A) Indian teak wood. (i) Fully

Panelled.(upto 10 ton) 5,285.45

(A) Indian teak wood. (ii) Fully

Glazed.(upto 10 ton) 4,595.06

(A) Indian teak wood. (iii) Partly panelled and

partly glazed. (upto 10 ton) 4,940.25

Providing and fixing 35 mm thick panelled,

glazed or panelled and glazed shutters for

Doors windows and clear story windows

including anodised alluminium But hinges

with necessary screws and indian teak wood

(A) Plywood sheet panels.

(B) Particle board panels

(C)Hard board panels.

(D) Asbestos sheet panels.

Providing and fixing 25 mm thick shutters

for cup boards etc. including black

28 10.00 enamelled M.S. butt hinges with necessary Smt

screws.(A) Indian teak wood. (i) Fully

Panelled. (upto 10 ton)

Providing and fixing 25 mm thick shutters for

cupboards etc. including anodised alluminium

butt hinges with necessary screws. (A) Indian 2,594.74

teak wood. (ii) Fully Glazed.

Providing and fixing 25 mm thick shutters for

cupboards etc. including anodised alluminium

butt hinges with necessary screws. (A) Indian 2,814.42

teak wood. (ii) Partly panelled and partly glazed.

Providing and fixing plain asbestos cement

sheet 6 mm thick in partitions including

fixing to fames with screws etc, complete with

50 mm x 12 mm Deodar wood beading 827.20

(Frames to be paid separately) (upto

Providing and fixing in partitions 4 mm thick

medium hard board of approved quality

including fixing to fames with screws etc

complete with 50 mm x 12 mm teak wood 516.60

beading (Frames to be paid separately)

25 mm thick wooden shelves supported

on 40 x 40 mm x 6 mm T or L iron brackets

31 10.00 fixed at suitable distances but not Smt

exceeding 75 cm. apart with Mango

wood or equivalent quality. (upto 10 ton)

40 mm thick wooden shelves supported

on 40 x 40mm x 6 mm T or L iron brackets fixed

32 4.00 at suitable distances not exceeding 75cm. Smt

Apart with Mango wood or equivalent

quality. (upto 10 ton)

Providing and fixing M.S. round or square bars

with M.S. flats at required spacing in wooden

frames of windows and clerestory 68.53

windows.(upto10 ton)

Providing and fixing M.S. grills of required

pattern to wooden frames of windows etc. with

M.S. flats at required spacings and

frame alround, square or round bars with round 100.17

headed bolts and nuts or by screws (A) Plain

Grill. (upto 10 ton)

Providing and fixing M.S. grills of required

pattern to wooden frames of windows etc. with

a 2.00 M.S. flats at required spacings and kg

frame alround, square or round bars with round

headed bolts and nuts or by screws (A)

Ornamental Grill. (upto 10 ton)

Providing and fixing glazed louvered

glass windows and ventilators with teak

35 2.00 wood frame 10 cm. x 7 cm. size including 3 Smt

coats of oil painting to wood work

etc.complete. (upto 10 ton)

Providing and fixing glazed louvered

glass windows and ventilators with teak

wood frame 10 cm.x7 cm. size including

coats of oil painting to wood work 4,332.47

etc.complete.with wooden louvers plank 12mm

thick (upto 10 ton)

Providing and fixing 35 mm thick shutters for

Doors, windows and clere story windows

including Indian teak wood frames 10 cm x 7 cm.

37 10.00 size including anodized alluminium fixtures Smt

and fastenings including primer coat of

approved quality and two coats of oil painting

etc, complete.(ii) Fully Glazed.

Providing and fixing 35 mm thick shutters for

Doors, windows and clere story windows

including Indian teak wood frames 10 cm x 7 cm.

38 4.00 size including black enamelled iron oxidixed Smt

fixtures and fastenings including primer coat

of approved quality and two coats of oil

painting etc, complete.(ii) Fully Panelled.

Providing and fixing 35 mm thick shutters for

Doors, windows and clerestory windows

including Indian teak wood frames 10 cm x 7 cm.

size including anodized alluminium fixtures

and fastenings including primer coat of approved 3,557.15

quality and two coats of oil painting

etc, complete. (iii) Partly panelled and partly

Providing and fixing 30mm thick FACTORY

SOLID BOTH SIDE PRELAM PANEL PVC

SHUTTER consisting of frame made out of

M.S.tubes of 19 gauge thickness and size of

19mm x 19mm for stiles, top and bottom rails.

M.S. frame shall have a coat of steel primer of

and manufactures. M.S frame covered with 5mm

thick heat moulded prelim PVC ‘C’ channel of siz

30mm thickness, 70 mm width of which 50mm

shall be flat and 20mm shall be tapered in

degree Angle on either side forming stiles, and

5mm thick, 95mm wide pream PVC sheet out of

which 75mm shall be flat and 20mm shall be

tapered in 45 degree on the inner side ot form

top and bottom rail and 115mm wide prelim PVc

39 8.00 sheet out of which Smt

75nmm shall be flat and 20mm shall be - 75nmm

shall be flat and 20mm shall be tapered on both

side to form lock rail, Top, bottom

and lock rails shall be provided either side of the

panel. 10mm (5mm x 2) thick 20mm wide cross

PVC sheet shall be provided as gap insert for

top rail and bottom rails. Panelling of 5mm thck

both side prelim PVC sheet to be fitted in the

M.S. frame welded,sealed to the stiles and rails

with 7mm (5mm + 2 mm) thick x 15mm wide

PVC sheet beading on inner side, and joined

solvent cement adhesive. An additional 5mm

thick PVC strip of 20mm width is to be stuck on

the interior side of the ‘C” chanel using PVC

solvent adhesive etc. complete as per direction

of Engineering in charge, manufacture’s

specification and rawing.

Providing and fixing in position collapsible

steel shutters with vertical channels 20 x

10 x 2 mm braced with flat iron diagonal 20 x6

mm size with top and bottom rails T iron 40 x

40 8.00 40 x 6 mm with 38 mm dia steel pulleys Sq.M.

complete with bolts, units, locking

arrangements, stoppers, handles, including

a priming coat of red lead paint & approved

Providing and fixing 1 mm thick M.S. sheet

sliding shutters with frame and diagonal

braces of 40x40x6 mm angle iron, 3.15 mm

M.S.gusset plates at Junctions and corners

41 2.00 mm dia. pulley, 40x40x6 mm angle and Sqm

T-iron huide rail at top and bottom

respactively with handles, stoppers and locking

agangement etc, including applying a

priming coat of red lead paint. (upto 10 ton)

Providing and fixing rolling shutters of approved

make made of 80 mm wide M.S.laths

inter-locked together through their entire length

and jointed together at theends by end locks

mounted on specially designed pipe shaft

42 7.00 with bracket plates, guide channels Sqm

and arragements for inside and out side

locking with push-pull operation including

the cost of hood cover and spring etc.

complete. (A) Shutters having width below

Providing and fixing rolling shutters of approved

make made of 80 mm wide M.S.laths

inter-locked together through their entire length

and jointed together at theends by end locks

mounted on specially designed pipe shaft

a 2.00 with bracket plates, guide channels Smt

and arragements for inside and out side

locking with push-pull operation including

the cost of hood cover and spring etc.

complete. (A) Shutters having 3.5 M. &

Providing and fixing extruded aluminum window

having extruded aluminum Colour Powder

Coated section frame main outer size 127mm x

1.35mm ,@ Wt.1.384 Kg/mt,horizontal Four

track member size 122.20mm x 31.75mm x

1.10mm @ Wt. 1.205 Kg/mt,vertical member of

size 122.20mm x 31.75mm x 1.50mm ,@ Wt.

43 10.00 1.398 Kg/mt with sliding shutters of horizontal Smt

member size 40mm x

18mm x 1.29mm @ wt.of 0.456Kg/mt,vertical

member of size 40mm x 18mm x 1.29mm @

wt.of 0.456Kg/mt,@ with 5 mm thick transparent

bronze colour tinted float glass with powder

coated aluminum fittings and fixtures and

transparent silicon sealant glass fixing to frame

as per details etc complete for window.

Providing and fixing window having extruded

aluminum Colour anodized section frame main

outer size 63.50 x 38.10 x 1.95 mm,@ Wt

Kg / Rmt, horizontal two track member size

Kg/mt, vertical member of size 61.85 mm x

31.75mm x 1.30 mm @ wt.of 0.659 Kg/mt with

sliding shutters of horizontal member size 40mm

x 18mm x 1.29mm @ wt.of 0.456Kg/mt, vertical 1,696.73

member of size 40mm x 18mm x 1.29mm @

wt.of 0.456Kg/mt, @ Wt. 0.457 Kg/mt with 5 mm

thick transparent bronze colour tinted float glass

with powder coated aluminum fittings

and fixtures and transparent silicon sealant glass

fixing to frame as per details etc complete for

Providing & Fixing in position Alluminium

vents with frame using approved anodised

extruded alluminium section as approved by

Engg. In charge.(Jindal alluminium)

45 10.00 units equivalent Approved Rate)Frame section Sq. M.

of 63.50 x 38.50 mm. (wt. 0.68Kg/Rmt)

incl. Providing & Installing 5 mmthick approved

color Acrylic sheet of standard quality

Providing and fixing standared extruded of

alluminium section of size 63 mmx38.10

mmx1.2 mm (Jindal Section:2434, @

46 10.00 Wt.0.643 Kg/mt) with colour anodized Sq. M.

alluminium frame for ventilation with 5 mm

thick frosted glass as details etc complete for

Providing and fixing standared extruded of

alluminium section of size 63.50 x 38.10 x

mm,@ Wt 1.094Kg / Rmt with colour Powder

Coated alluminium frame with 5 mm thick 1,509.90

transparent bronze colour tinted float glass as

details etc complete for Fix Partition

Providing and laying 40 mm thick marble

chips flooring rubbed and polished (I.E.terrazo)

to granolithic finish with under layer 30 mm thick

cement concrete1:2:4 (1-Cement: 2-coarse

sand: 4-graded stone aggregate 10 mm

and down gauge) and to player 10 mm thick

48 1.00 with white, black or white and blak marble cihps Sqm

of required sizes from 1 mm to 4 mm nominal

size laid in cement marble powder mix 3:1 (3-

Cement:1-Marble powder by weight) in

proportion of 4:7 (4- Cement: 7-marble

chips by volume) (C) Medium Shade

pigment with approx 50% white cement

and 50% ordinary cement (In top layer only)

Providing and laying marble chips skirting

(Terrazo) or dedo rubbed, and polished to

Granolithic finish to player 6 mm white, black

or white and black marble chips of size

from smallest to 4 mm nominal size laid in

cement marble powder mix 3:1 (3-Cement: 869.40

1 marble powder by weight) in proportion of

4:7 (4-cement marble powder mix: 7-marble

chips by volume) (B) Light shade pigment with

white cement (In top layer only)

Providing and laying white glazed tiles 6mm

thick in flooring treads of steps and landing laid

50 2.00 on a bed of 12mm thick cement mortar 1:3 (1- Sq.M.

cement : 3-coarse sand ) finishing with flush

pointing in white cement.

Providing and laying Ceramic tiles 6 mm thick

in flooring treads of steps and landing laid on a

51 10.00 bed of 12 mm thick cement mortar 1:3 (1- Sq.M.

cement :3-coarses and) finishing with flush

pointing in white cement. (upto 10 ton)

Providing & Fixing 2mm Aluminium / 4mmACP

sheeting fixed with Type-11 Class-C High

Intensity Grade Sheeting as per IRC 67 :

reflective sheeting of size including lettering and 5,832.20

Providing and laying Vitrified tiles 8 to 10 mm

thick, 36''x36'' in flooring treads of steps and

landing laid on a bed of 12 mm thick

cement mortar 1:3 (1-cement:3-coarses and) 1,469.91

finishing with flush pointing inwhite cement. (upto

Providing and laying Vitrified tiles 8 to 10 mm

thick, 24''x24'' in skrting risers of steps and dedo

54 30.00 on 10 mm thick cement plaster 1:3 (1- Sqm

cement: 3-coarse sand) and jointed with

white cement slurry (upto 10 ton)

Providing and laying Vitrified tiles 8 to 10 mm

thick, in skrting risers of steps and dedo on

55 20.00 mm thick cement plaster 1:3 (1-cement:3- Sqm

coarse sand) and jointed with white cement

slurry (upto 10 ton)

Providing and laying 24" x 24" vitrified

Tiles 8 to 10 mm th. Double Charged

gloosy/ Matt of Approved make as approved

by Adl.C.E. / consultants in flooring over

mm thick cement mortar 1:6 (1 cement : 6 1,527.00

coarse sand)on new surface& jointed with

colour cement slurry incl with flush

pointing & cleaning the surface etc. comp.

Providing and laying 24" x 24" vitrified

to 10 mm th.Double Charged Gloosy /

Matt tiles of Approved make as Approved

by Adl.C.E. / Consultants for upto 10 cm high

57 10.00 skirting as approved by Engineer in charge Rmt

over 10 mm thick cement mortar 1:6 (1 cement

: 6 coarse sand)on new surface& jointed with

colour cement slurry incl with flush pointing &

cleaning the surface etc. comp.

Providing and laying polished Kota stone slab

flooring over 20 mm (Average) thick base

of cement mortar 1:6 (1-cement:6-coarses

and) or L.M.1.1.5 (1-Lime putty:1.5-

58 15.00 coarses and) laid over and jointed with grey Sq.M.

cement slurry mixed with pigment to match

the shade of slab including rubbing and

polishing etc. complete. (A) 25 mm thick (upto

Providing and laying marble stone slab flooring

over 20mm (average)base of cement mortar 1:6

(1-cement : 6 coarse sand) or L.M. 1:1.5(1- lime

putty : 1.5 - coarse sand) laid and jointed with 2,194.63

gray cement slurry including rubbing and

polishing complete. (A) Marble slab 25mmthick

Providing and laying polished Kota stone slab

flooring over 20 mm (Average) thick base

of cement mortar 1:6 (1-cement:6-coarses

60 2.00 and) or L.M.1.1.5 laid over and jointed with Sq.M.

grey cement slurry including rubbing and

polishing etc.complete. (B) 30 mm thick

Providing and laying polished kota stone slab

mm thick in risers of steps, skirting Dedo and

pillars laid on 10 mm thick cement mortar 1:3 (1-

61 2.00 Cement :3 coarses and) and jointed with Sq.M.

gray cement slury mixed with pigment to

match the shade of slab including rubbing

and polishing etc.complete. (upto 10 ton)

Providing and laying cement concrete

flooring 1:2:4 (1-cement: 2-coarses and:4-

62 2.00 graded stone aggregate 20mm nominal size) Sq.M.

laid in one layer and finished with a floating

coat of neat cement. (A) 40mm thick. (upto

Providing and laying cement concrete

flooring 1:2:4 (1-cement: 2-coarse sand:4-

graded stone aggregate 20mm nominal size)

laid in one layer and finished with a floating 348.08

coat of neat cement. (B) 50mm thick. (upto

Providing and fixing pre-cast concrete

kerb stone of gray cement based

concrete block 30 cm length, 30 cm height and

15 cm thick of M200 grade concret as per

approved design and including excavation 376.43

for fixing in proper line and level, filling the joint

with C:M 1:3 (1 cement :3 fine sand) etc

complete. (upto 10 ton)

Providing and fixing pre-cast Rubber Dye / steel

Dye inter locking concrete block 60mm thick

with grade of concrete M300 pnumatic

compressed / vibrated mechanically and as per

65 2.00 approved design Confirming to IS 15658 : 2006 Smt

including 35 mm Sand layer for levelling

and filling the joint with sand in proper line and

level as per guidlines of IRC : SP 63-2018 etc.

Providing and laying broken china mosaic

flooring for terrace using 12 mm to 20 mm

broken pieces of glazed tiles to be laid over

cement mortar 1:3 to plain or slope and to be

66 5.00 tempered to bring mortar creme out upto Sqm

surface using white cement including

rounding off junctions and extending them

up to15 cm along the wall, clearing with

water and oxalic acid etc.asdirected.

Providing and laying coloured glazed

tiles of the size 300 mmx200 mmx8

mm/300 mmx450 mmx8 mm in skirting,

risers of steps and dedo on 10 mm. thick 1,426.95

cement plaster 1:3 (1cement: 3 coarse

sand) & jointed with white cement slurry.

Providing corrugated G.I. sheet of class-3

roofing fixed with glavanished iron J

or L Hooks, Bolts and nuts 8 mm diameter

68 5.00 with bitumen and G.I. limpet washer or G.I. Sqm

limpet washer. filled with white lead complete

excluding the cost of purlins, Rafters and

Trusses. (1) 0.80 mm thick sheet.(up to10 ton)

Providing ridges or hips 600 mm over allin

69 2.00 plain G.I. sheet class-3 fixed with G.I. J or L Sqm

Hooks and nuts 8 mm dia G.I. Limpet and 635.58

bitumen washer complete. (1)

Providing and fixing 150 mm wide 450 mm over

all semi circular plain G.I.sheet class-3 gutter

with Iron brackets 40 mmx3 mm size Bolts,

Nuts, washers etc. including making 555.71

necessary connection with rain water pipes. (i)

Providing and fixing five courses water

profing treatment with bitumen felt

consisting of second and fourth course of

blown/ bitumen or/and residual bitumen

applied hot at 1.2 kg.per Sq.M.of area for

each course and first course with fibre

base bitunen saturated under lay type land third

course with fibre base self finished felt type 2 466.84

grade 1 and fifth and final course of stone grit

6 mm and down size or pea sizes gravel

Cu.Metre/Sq.metre preparation of surface

excluding grading complete. (upto 10 ton)

Providing and fixing on wall face C.I. Rain

water pipe including filling the joints with spun

72 1.00 yarn soaked in neat cement slurry and Rmt

cement mortar 1:2(1- Cement : 2-fine

sand) (A) 75 mm dia.

Providing 15 mm thick cement plaster in

single coat on Rough (Similar) side of single or

73 2.00 half brick walls for interior plastering up to Sqm

floor two level and finished even and smooth

in (i) Cement mortar 1:3 (1-cement :3-sand)

Providing 20mm thick sand faced cement plaster

on walls upto height 10 metres above ground

level consisting of 12mm thick backing coat of

C.M. 1:3 (1-cement : 3-sand) and 8mm thick 215.78

finishing coat of C.M. 1:1 (1-cement : 1-sand)

Colour washing with lime on wall surface

(two coats) over and including a primary

coat of white washing to give an even shade

after through brooming the surface to remove 12.29

all dirt, dust, mortar drops and other foreigh

Removing dry or oil bound distemper

by a washing and scraping and sand

papering the wall surface smooth including 11.19

necessary repairs to scratches complete.

Distempering with dry distemper of approved

brand and manufacture (two coats) and of

required shade on wall surfaces of given an

77 5000.00 even shade, over and including a priming Sqm

coat of whiting after thoroughly brooming

the surface free from mortar dropping and

other foreign matter.

Extra Coat for Above Item over above for

77 a 5000.00 every subsequent coat of approved brand Sqm

and manufacture.

Distempeing (Two coats) with oil bound

distemper of approved brand and

manufacture and of required shade on wall

surfaces to give an even shade, over and

including a priming coat with distemper

78 5000.00 primer of approved brand and Sqm

manufacture after thoroughly brushing the

surface free from mortar dropping and other

foreign matter and also including

preparing the surface even and sand papered

Extra Coat for Above Item over above for

79 5000.00 every subsequent coat of approved brand Sqm

and manufacture.

Wall painting (two coats) with plastic

emulsion paint of approved brand and

manufacture on undecorated wall surface to

give an even shade including throughly brushing 78.44

the surface free from mortar droppings and

other foreign matter and sand papered smooth.

Extra over item for every sub sequent coat of

81 5000.00 wall painting with plastic emulsion paint of Sqm

Extra over item for painting with plastic emulsion

81 a 5000.00 paint of approved brand on ceilings and sloping smt

Applying priming coat over new steel and

other metel surface after and including

preparing the surface by throughly cleaning,

82 1500.00 oil, grease, dirt and other foreign matter Sqm

and scoured with brushes fine steel wood,

scrapers and sand paper with ready mixed

priming paint brushing red lead.

Painting two coats (excluding priming

coat) on new steel and other metal surface

with enamel paint, brushing, interior to give

an even shade including cleaning the surface 86.94

an even shade including cleaning the surface

of all dirt, dust and other foreign matter.

Painting one coats (excluding priming coat)

on previously painted steel and other metal

84 2000.00 surface with enamel paint, brushing to give Sqm

an even shade including cleaning the surface of

all dirt, dust and other foreign matter.

Extra over item for 83 & 84 every sub sequent

coat of paint. 50.40

Painting two coats (excluding priming

coat) on new steel and other metal surface

86 2000.00 with synthetic enamel paint, brushing to give Sqm

an even shade including cleaning the

surfaceofalldirt,dust and other foreign matter.

Painting one coats (excluding priming coat)

on previously printed steel and other metal

87 2000.00 surface with synthetic enamel paint, brushing to Sqm

give an even shade including cleaning the

surface of all dirt, dust and other foreign matter.

Extra over Above item for 86 & 87 for every

sub sequent coat of paint. 43.47

Painting two coats (excluding priming

coat) on external surface of new rain water,

soil, waste and vent pipes and fittings with

89 2000.00 ready mixed bituminous brushing, black, anti Sqm

corrosive to give an even shade including

cleaning of all dirt, dustand other foreign

matter.(75 mm dia)

Painting two coats (excluding priming

coat) on external surface of new rain water,

soil, waste and vent pipes and fittings with

90 2000.00 ready mixed bituminous brushing, black, anti Sqm

corrosive to give an even shade including

cleaning of all dirt, dust and other foreign

matter.(100 mm dia)

Painting two coats (excluding priming

coat) on new wood and wood based surface

with enamel paint, interior to give an even

91 2000.00 shade including cleaning the surface of Sqm

all dirt, dust and other foreign matter sand

papering and stopping. (a) Ready mixed paint

brushing wood primier pink.

Painting one coats (excluding priming coat)

on previously painted wood and wood based

surface with enamel paint, to give an even shade

including cleaning the of all dirt, dust and other 40.17

foreign matter.(b) Ready mixed paintbrushing

priming for enamel

Extra over Above item for 91 & 92 every sub

sequent coat of paint. 36.39

Painting two coats (excluding priming coat) on

wood and wood based surface with ready mixed

94 2000.00 paint, brushing, oil, gloss, semi gloss to give and Sqm

even shade including cleaning of all dust, dirt

other foreign matter sand papering and stopping.

Finishing wall with weather proof exterior

emulsion paint on wall surface (two coats)

to give an required shape even shade after

thoroughly brushing the surface to remove all 113.40

dirt, and remains of loose powdered

materials.etc complete

Applying two coats of putty & two coats of primer

of approved brand and manufacture on new wall

surface to give an even shade including

96 5000.00 thoroughly Sqm

brushing the surface free from mortar dropping

other foreign matter and sand papered smooth.

Painting two coats (excluding priming

coat) on new wood and wood based surface

with enamel paint, interior to give an even

shade including cleaning the surface of 87.11

all dirt, dust and other foreign matter sand

papering and stopping.

Writing letter or figures on any surface

with black japan paint (stops, comas, per letter

98 10.00 hyphens and the like not to be measured per

and paid for separately) (i) Block Cm/Ht

(Letters/Figures) (Per 10 Letter pet CM.HT)

Extra over items for using thick white paint per letter

instead of black japan paint. (i)Block per

(Letters/Figures) Cm/Ht

Polishing with french polish on new wood and

wood based surface to give an even

surface including cleaning, the surface of all dirt,

100 10.00 dust and Smt

sand papering smooth and including a coat of

Extra over items for using thick white paint

instead of black japan paint. (ii) Indian

101 10.00 0.07 perCm/Ht

(Letters/Figures)

Painting lines, deashes, arrows, letters etc

on roads, Air fields and like in two coats with

102 10.00 road marking paint, brushing including Sqm

cleaning the surface of all dirt, dust and other

foreign matter. (i)Over 10cmi n width

Painting lines, deashes, arrows, letters etc

on roads, Air fields and like in two coats with

103 10.00 road marking paint, brushing including Rmt

cleaning the surface of all dirt, dust and other

foreign matter.(ii) Upto 10 cm in width

Painting lines, deashes, arrows, letters etc on

roads, Air fields and like in one coats with road

104 10.00 marking paint, brushing including cleaning the Sqm

surface of all dirt, dust and other foreign matter.

(i) Over 10cm in width

Painting lines, deashes, arrows, letters etc

on roads, Air fields and like in one coats with

105 10.00 road marking paint, brushing including Sqm

cleaning the surface of all dirt, dust and other

foreign matter. (ii) Upto 10cm in width

Demolition including stacking of serviceable

106 10.00 materilas and disposal of unserviceable Cu.M.

materials with all lead and lift. (i) R.C.C. work

Demolition of Brick work and stone masonry

including stacking of serviceable materil as

and disposalof unserviceable materials with all 544.95

lead and lift.(ii) In Cement Mortar.

Demolition of terrace including stacking of

serviceable materilas and disposal of

unserviceable materials with all lead and lift.(i) 63.00

Brick tile covering.

Dismentaling tiled of stone floors laid in mortar

including stacking of serviceable materil as and

disposal of unserviceable materials with all 47.25

Dismentaling of sheet roofing including

ridges, Hips, Valleys, Gutters etc. stacking of

109 2.00 serviceable materil as and disposal of Sqm

unserviceable materials with all lead and

lift.(i) G.I.sheet roofing.

Dismentaling of sheet roofing including

ridges, Hips, Valleys, Gutters etc. stacking of

109 A 2.00 serviceable materil as and disposal of Sqm

unserviceable materials with all lead and

lift.(i) A.C. sheet roofing.

Dismentling steel work including

110 2.00 distempering and stacking the materials Kg.

with all lead and lift.

Dismentling doors, windows, ventilators

etc. (wood or steel) shutters including

chowkhats architraves, hold fasts and other

attachment etc. complete and stacking the 185.85

material within all lead and lift.(i) Not exceeding

3 Sq.M. in area.

Dismentling doors, windows, ventilators

etc. (wood or steel) shutters including

chowkhats architraves,hold fasts and other

attachment etc. complete and stacking the 248.85

material with in all lead and lift.(ii) Exceeding

Dismentling barbed wire in fencing including

making rolls and also including dismentling

fencing posts including all earth work concrete in

base and making good the disturbed

ground stacking useful materials as 66.15

directed and disposing as directed

and disposing of the unserviceable

materials with all lead and lift.

Dismentling C.I. pipes G.S.W. pipes abd

A.C. rain water pipes with fittings and clamps

including stacking the materials with all lead and 74.03

lift (for any dia, of pipe)

Dismantling santtary fittings like wash basin .

W.C. pan Indian and Europe an type, flushing

tank etc. including stacking the materials 401.63

with all lead and lift

Scraping oil paint from steel and other metal

116 10.00 surface and making the surface even Smt

(with Hand Scraping.)

Removing and scraping of old deteriorated

plaster of any thickness from wall /

R.C.C member including stacking of

serviceable material and disposal of 19.38

unserviceable from site of work with all lead

Providing and fixing M.S. fan clamps of

shape and size as specified in existing

R.C.C. slab including cutting chase and making 168.53

Cutting out cracks of roof terrace to V-

section, cleaning out, wetting, grouting with

cement and sand slurry 1:3 (1-cement 3-sand 64.58

) (upto 10 ton)

Cutting out cracks roof terrace to V-Section

cleaning out and filling solidly with a hot

mixture of bitumen and clean dry sand (1:1 75.29

by weight) (up to 10 ton)

Providing & Fixing in position Alluminium

doors with frame using approved quality

anodised extruded alluminium section as

approved by Engg.in charge(Jindal

alluminium)(a) Frame sections 101.6x44.45

mm (b) Shutter bottom vertical & top

section 83.5x44.45 (wt.1.31 kg/mt.)(at

kg/mt) (c) Shutter bottom section at

114.3x44.45 mm at (1.37 kg/mt) Shutter middle 2,900.00

section at 100x44.3 wt.(1.37 kg/mt)

incl.providing & installing 5 mm thick

approved color Acrylic sheet of standard

quality fixed with glazing chips on upper

pannel & Laminated sheet on lower pannel

(wtt.0.13 kg/Rmt) etc.comp.as direction of

engg.in charge.(N.S.)

Providing & Fixing in position Fully Panelled /

Partly Panelled Partly Glazed / Fully Glazed

Alluminium doors with frame using approved

quality anodised extruded alluminium

section of 1.5 mm thickness as approved by

Engg. In charge.(Jindal alluminium )(a) Frame

sections 101.6x44.45 mm b) Shutter vertical

& top section 83.5x44.45 (wt.

kg/mt.)( at 1.31 kg/mt) © Shutter bottom 4,583.00

section at 114.3 x44.45mm at ( 1.37 kg/mt )

Shutter middle section at 100x44.3 wt. (1.37

kg/mt ) incl. providing & installing 5 mm thick

Glass of standaed quality fixed / 12 mm

thick Laminated sheet with glazing chips (wt.

0.13 kg/ Rmt) in panels etc. comp. as per

Detail Given & direction of engg.in charge.

Providing & Fixing in position Alluminium

window 2/3/4 track sliding / fix type with

frame using approved anodised extruded

alluminium section of minium thickness of

123 1.00 mm as approved by Engg. In Sq. M.

charge.(Jindal alluminium) units

equivalent. including P/F installing 5 mm thick

clear/tinted Glass of standard quality

Providing and fixing standared extruded of

alluminium section of size 63.50 x 38.10 x

mm,@ Wt 1.094Kg / Rmt with colour Powder

Coated alluminium frame with 1,815.14

5 mm thick transparent bronze colour tinted float

glass as details etc complete for Fix window.

Providing and fixing of Ridge flashing

for roof panel shall be made out of

mm thick pre coated GI sheet. The Pre

coatedsheet shall be of minimum 240 mpa

steel grade confirming to IS 14246:1995 and

shall have zinc coating of minimum 120 gsm

as per IS:277:1992, 5-7 microns epoxy

primer on both side of the sheet and

polyester top coat 15-18 micron. The PP GI 458.85

Sheet shall have plastic protective guard film

of minimum 25 microns to avoid scratches

during transportation. The ridge shall be fixed

to the steel members by poprivetor self

drilling/self stitching fastners @ maximum

450mm c/c along length of capping/flashing etc

Supplying and fixing vinyl flooring over the

surface having 1-2 mm thickness as per

directed by engineer incharge etc 963.00

as completed (N.S.)

Providing and laying 15mm bamboza

wooden flooring as per architect's drawing

with all necessary details as directed by

127 2.00 the project consultants. Use underlay for Smt

better result as per Detail specifications and

directed by the project consultants. (N.S.)

Approved Rate )

Providing and fixing 1.20 Metre high

fencing with 2.0 Metre long M.S. Angle posts

40 mm x 40 mm x 6 mm and oil painting

coats fixed at 2.5 Mt, C/c. with five

Horizontan lines and two diagonals of

galvanised steel barbed wire weighting 9.38 385.40

Kg. per 100 Metre, strained and fixed to posts

with G.I, staples including fixing the posts in

ground with 0.5 M x 0.5.M x 0.5 M. block in

C.C 1:5:10 etc complete.

Dismentling barbed wire in fencing including

making rolls and also including dismentling

posts including all earth work concrete in base

129 2.00 making good the disturbed ground stacking Rmt.

materials as directed and disposing as directed

disposing of the unserviceable materials with all

Constructing a sink (chowkedi) with C.C.

1:2:4, 12 cm. thick over B.B. masonry in C.M,

(1:6) in front and dwarf wall 1.0 Mt. high and

cm. thick cement plaster to masonry / in 2,235.66

C.M.1:3) and cement concrete flooring in 1:2:4:

mix 5cm.dia.drain pipe etc.complete.

Constructing a cooking platform 60 cm. width

and 70 cm high resting on B.B. Masonry walls

23 cm. thick in C.M. (1:6) with (i) Fixing

131 2.00 or precast R.C.C. 1:2:4) 8 cm. thick slab with Rmt

marble chips set in C.M. (1:6) (6 mm thick

terrazo) with plastering on exposed faces

walls in C.M. (1:4) etc complete.

Making 15 mm groove in RCC work on road and

filling it with polysulfied selant and finished it

good incl. all all labour charges etc. comp as 30.00

P/A Tremix with dewartering machine

and floater machine on constructed CC work

for finishing the surface as per

133 2.00 requirement. The rate including all machinaries, Sq.M.

labor, loading, unloading,

transportaion etc complete as per direction

given by engineer incharge.

Carring out timber treatment to all wood work

including drilling holes and spraying oil based

chemical solution on surface of timber work for

termite control including labour and material

etc. complete. Using Chlordene 20 EC.

As Per 6113_part III Consentration

134 2.00 Weight1.00 percent is recommended one litre Smt

chemical emulsion dillute with 9 liter of

kerosene precent concentration. Total

dillute concrentration will be 10 litre

inclusive of the litre chemical emulsion

appication 0.75 / Litre chemical per one

Sqmt printed two coat wood surface.

Applying general insecticide pest control

treatment to floors, cup boards etc

including labour material etc. complete.

Using Heptachloride 20 EC. As Per

6113_pests Consentration Weight

135 2.00 percentis recommended one litre chemical Smt

emulsion dillute with 39 liter of water will give.

Total dillute concrentration will be 40 litre

inclusive of one litre chemical emulsion

appication 0.5 Litre chemical / Sqm of

surface is recommended as per I.S

Carring out plinth treatment to post construction /

existing structure by spraying chemical

solution for termite control treatment

including labour and material consist ment

with I.S. specification. Using Chlordene

and Chior purfiles 20 EC. As Per

6131_paret-II Consentration Weight on percentis 104.90

recommended i.e one litre 20 EC chemical

emulsion with 19 liter give 1% concrentration

inclusive of one litre chemical emulsion

appication attherate of 5 Litre chemical /

Sqm of surface is recommended as per I.S

Carrying out wall treatment for termite

control including spraying with chemical

solution in oil base (0.5 Lit./Sq.M.) including

labour and material Using Hepachlor

concentration 20 EC. As Per

IS.6316_paret-II Consentration by Weight

137 2.00 0.50 percentis recommended i.e Smt

one litre chemical emulsion dillute with

liter go fIS concrentration total dillite

concentration will be 40 litre inclusive of one

litre chemical emulsion appication at the rate

of 7.5 Litre chemical / Sqm of surface is

recommended as per I.S

Providing erecting and fixing double

coated Syntex PVC.(ISI) water tank of

138 500.00 required capacity each with all necessary Litre

fittings and connection etc. complete on

Providing and fixing to wall, ceiling and floor

galvanised Mild steel tubes (Medium

139 grade) of the following nominal bore, tube

fitting and clamps including making good the wall

ceiling and floor.

(A) 15mm (upto 10 ton)

(B) 20mm (upto 10 ton)

(C) 25mm (upto 10 ton)

(D) 32mm (upto 10 ton)

(E) 40mm (upto 10 ton)

(F) 50mm (upto 10 ton)

Providing and laying in trenches galvanised

mild steel tubes (Midium grade) of the

following nominal bore, and tube fitting

(Earth work in trenches to be measured

and paid for separately)

(A) 15mm (upto 10 ton)

(B) 20mm (upto 10 ton)

(C) 25mm (upto 10 ton)

(D) 40mm (upto 10 ton)

(E) 65mm (upto 10 ton)

(H) 80mm (upto 10 ton)

Making connection of galvanised Mild steel

distribution branch with galvanised mild steel

141 1.00 main 50 mm to 80 mm nominal bore by Each

providing and fixing tee including cutting and

threading the pipes complete.

Providing and fixing to wall ceiling and floor

Kg.F/Cm2 working pressure poluthene pipes

of the following out side Dia. Low

142 densidy, complete with special falnge

compression type fittings,wall clips

etc.including making good the wall ceiling and

Providing and fixing to wall ceiling and floor

10.0Kg.F/Cm2 working pressure polythene

pipes of the following out side Dia.

143 Low densidy, complete with special falnge

compression type fittings, wall clips etc.

including making good the wall ceiling and

Providing and fixing cast iron (Spun)

Nahni trap of the following nominal diameter

of self cleaning design with C.I. screaed

down or higned grating including cost of 600.08

cutting and making good the walls and floor

mm inlet and 50 mm outlet.(C)100mm dia.

Providing and fixing water closet squatting

Pan (Indian type W.C.Pan) size

mm (Earth work, bed concrete, foot rest and

trap to be measured and paid for separately) 926.10

(A) Vitreous China. (I)Long pattern = White

Provdg. & fixing wall mounted White /

Color Vitreous China European water

closet with integral P trap of "Cera" -

Clair Series or equivalent incl. seat cover , 4,250.00

Chair Bracket etc. complete as per direction of

engg. In charge.(N.S.)

Providing and fixing wsh down water

closet (Europe an type, W.C.Pan) with

integral P or S trap including jointing the trap

147 15.00 with soil pipe in Cement Mortar1:1 (1- Each

Cement:1-fine sand) (Seal and cover to be

measured and paid forseparately) (A)

vitreous China Pattern :(i) in white colour

Providing and fixing Urinal of approved quality

including connection with trap and with integral

148 10.00 longitudinal flush pipe.(A) Squating plate pattern No.

white earthenware 550mm x 300mm.

Providing & Fixing Angle cock of " Ess Ess" -

Trend series or equivalent standard

make as approved by engg. in charge all 403.39

complete. (N.S.)

Providing & Fixing pillar cock of " Ess Ess" -

Trend series or equivalent standard

make as approved by engg. in charge all 641.53

complete. (N.S.)

Providing and fixing 100 mm size P or S

trap for water closet squatting pan including

150 18.00 jointing the trap with the pan and soil pipe in Each

cement Mortar1:1 (1-Cement : 1-Fine

sand)(A) Vitreous China.Pattern in white colour

Providing and fixing washbasin with single hole

pillar tap with C.I. or M.S. brackets painted white

including sutting holes and making good the

but excluding fittings.(A) Vitreous China:(ii) Flat

Back washbasin 550 mm x v 400mm size. (i) In

Providing and fixing Kitchen sink with C.I. or

M.S. brackets, painted white including cutting

152 15.00 holes in walls and making good the same Each

but excluding fittings. © Vitreous China Sink.

(i) 600 mm x 450 mmx 150 mm size

Providing and fixing 600 mm x 450 mm

bevelled edge mirrror of superior glass

153 15.00 mounted on 6 mm thick A.C. sheet or ply wood Each

sheet and fixing to wooden pluge with C.P.

brass screws and washers.

Providing and fixing chromium plated brass

154 halftrun flush cock of approved quality including

fixing in pipe line etc. complete.(ii) 25mm dia.

Provdg. & fixing White / Color Vitreous

china Counter wash basin with signle hole for

pillar tap of "Cera " - Concord series of

x425 mm size to be fiited in stone counter with

necessary brackets painted white incl.

155 25.00 cutting holes and making good the same No.

.Cost Includes P/F C.P. brass waste

coupline, 32 mm dia fisher union ,15 mm dia.

Pillar cock & Angle cock of " Ess Ess"- Trend

series ,32 mm dia. Waste pipe etc.

complete as per dir. of engg. in charge.

Finishing wall with water proofing cement paint

on wall surfaces (Two coats) to give an

156 1000.00 brand and manufacture and of required shape Smt

even shade after thoroughly brushing the

remove all dirt and remains of loose powered

Extra over Item 156 for every subsequent coat

156 a 1000.00 ofwater proofing cement paint of approved Smt

brandand manufacture. 31.82

Providing & Fixing S.S.304 Grade Sink of

Nirali / Krishna or Equivalent Make for

Kitchen Platform of size : 24":x18" as per 4,650.00

Direction of engg. In charge

Providing and fixing Kitchen sink with C.I. or

brackets, painted white including cutting holes in

157A 2.00 walls and making good the same but excluding Each

fittings. (C) Vitreous China Sink.(i) 600mm x

Providing and fixing C.P. brass towel rail

comlete with C.P.brass brackets fixed to

wooden plugs with C.P. brass scews.(B) 597.22

600mm x 20mm size.

Providing and fixing 600 mmx120 mm glass

shelf with C.P. brass bracket and guard rail

complete mixed to wooden plug with 561.03

C.P.brass screws.

Providing and fixing toilet paper holder. (A)

C.P.Brass 414.53

Providing and fixingof S.S. Railing pipe 50 mm x

161 1.00 16 G ASIS 304 Grade as per instruction of

engineer in charge.

Providing and fixing screw down bib taps of

162 following size. (B) Brass chromium plated

screws down Bib Tap.

Providing and fixing screw down bib taps of

163 following size. © Gun metal screw down bib

Providing and fixing pillar tap, capstan

164 head, screw down high pressure with screws,

shanks and back nuts.

Providing and fixing Gun metal check or

non-return fullway wheel valve.

(III) 25 MM DIA

Providing and fixing brass screw down stop

165 A 10.00 Each

tap.(A) 15 mm dia 203.79

Providing and fixing chromium plated brass

166 10.00 half trun flush cock of approved quality including

fixing in pipe line etc. complete.

(iii) 32mm dia.

Providing and fixing Urinal or approved

quality including conecting the Urinal

167 10.00 with waste pipe , tap etc.complete. (A) White Each

earthen ware flat back or corner type size

Providing and fixing Urinal of approved

quality including connection with trap

168 10.00 and with integral longitudinal flush pipe. (A) Each

Squating plate pattern white earthen

ware 550mm x 300mm.

Providing and fixing chromium plated,

169 10.00 bottle trap with necessary couplings of Each

approved quality for wash basin.

Providing and fixing ball cock ofapproved

170 10.00 quality as directed. (A) Copper Metal (i) 25mm Each

Providing and fixing ball cock ofapproved

171 10.00 quality as directed. (A) Copper Metal (i) 50 mm Each

Filling with good Quality thor as and where

directed by the Architect / Engineer-in-

charge, in sunk in layers of 15 cm. thickness,

including watering, ramming well etc. 3,850.00

complete, as directed by the Architect /

Engineer-in-charge .

Providing laying and jointing in true line and level

15 mm dia. U.P.V.C. Pipe (SCH-40) for

cold water including fittings make PRINCE/

SUPREME/ ASTRAL/ FINOLEX or equivalent

as approved by Engineer In Charge. Pipe

173 10.00 shall be fixed on the wall with the help of Rmt

clamp at every two metre C/C or shall be

concelled as directed including necessary

fittings etc. including testing of pipe and joints

and fixing the same with solvent, including

cost of all materials.adhesive

Providing laying and jointing in true line and level

25 mm dia. U.P.V.C. Pipe (SCH-40) for

cold water including fittings make PRINCE/

SUPREME/ ASTRAL/ FINOLEX orequivalent

as approved by Engineer In Charge. Pipe

174 10.00 shall be fixed on the wall with the help of Rmt

clamp at every two metre C/C or shall be

concelled as directed including necessary

fittings etc. including testing of pipe and joints

and fixing the same with adhesive solvent,

including cost of all materials.

Providing laying and jointing in true line and level

32 mm dia. U.P.V.C. Pipe (SCH-40) for

cold water including fittings make PRINCE/

SUPREME/ ASTRAL/ FINOLEX or equivalent

as approved by Engineer In Charge. Pipe

175 15.00 shall be fixed on the wall with the help of Rmt

clamp at every two metre C/C or shall be

concelled as directed including necessary

fittings etc. including testing of pipe and joints

and fixing the same with adhesive solvent,

including cost of all materials.

Providing laying and jointing in true line and level

40 mm dia. U.P.V.C. Pipe (SCH-40) for

cold water including fittings make PRINCE/

SUPREME/ ASTRAL/ FINOLEX or equivalent

as approved by Engineer In Charge. Pipe

176 1.00 shall be fixed on the wall with the help of Rmt

clamp at every two metre C/C or shall be

concelled as directed including necessary

fittings etc. including testing of pipe and joints

and fixing the same with adhesive solvent,

including cost of all materials.

Providing laying and jointing in true line and level

50 mm dia. U.P.V.C. Pipe (SCH-40) for

cold water including fittings make PRINCE/

SUPREME/ ASTRAL/ FINOLEX or equivalent

as approved by Engineer In Charge. Pipe

a 10.00 shall be fixed on the wall with the help of Rmt

clamp at every two metre C/C or shall be

concelled as directed including necessary

fittings etc. including testing of pipe and joints

and fixing the same with adhesive solvent,

including cost of all materials.

Providing and fixing premoulded compressible

filler board in black colour confirming to

MoRT&H Specifications (Clause 1015), having

177 5.00 minimum density 95kg/cum. non-staining with Smt

less than 1% water absorption & compression

recovery of 93% minimum as per specification

for 20 mm wide expansion joint including cutting

to required size and shape at all levels

etc.complete as directed.

Fixing sun film for protection sunlight in black or

178 5.00 any colour as as directd by engineer In Smt

Charge.(Market rate)

Providing & Fixing 3 mm thick F.R.P.sheet

of Approved Quality & Color / Pattern as per

Consultant's design also includes required

fabrication structure in the grid of 2'-0x2'-0

size using hollow pipe of16 gauge & size

179 30.00 2"x1" & 1"x1" ,G.I. & Bitumen Washers, SqM

Silicon paste application for fixing the sheet

. Rate also includesnecessary bending, cutting,

labor charges , Zinc Primer coat & Two coats

of oil painting of color as approved by

consultants & making good the wall. (N.S.)

Providing 2 mm thick F.R.P. Gutter with

180 15.00 necessary M.S. Supporting Brackets. (N.S.) Rmt

Hiring charges for J.C.B.machine inclduing

181 6.00 cost of fuel, operator, dirver etc.. ( 12 Hrs.

hours sift day/night) (N.S.)

To provide tractor with hydraulic trolley, driver,

4 Nos. of Labor with all tools like bucket drum,

showels, trikam, pavadas, etc,, to

182 5.00 carryout different works during monsoon for No.

12 Hrs. Shift. Work shall be carried out as

per the instrucitons of Engineer In-Charge.No

extra charged shall be paid for night shift.

Roller Blind Providing and fixing Roller Blind

curtain fixed on window level on wooden

batten and curtain lift with cotton thin rope,

183 1.00 make of aerolax or equivalent design Smt

and colour as per instruction by engineer –

in – Charge with necessary hardware fitting,

material and labour etc complete.

Providing & Fixing Door closer - complete of

184 5.00 Approved make to wooden / Aluminium Doors as No.

per direction of engg. In charge.

Providing and fixiing M.S. Fan clamps type 1 of

16 mm dia M.S. bar bent to shape with hooked

185 5.00 ends of R.C.C. slabs during laying incl. painting No.

the exposed protion of loops, all as per standard

design complete.

Providing cement vata (10cm. x 10 cm. size)

186 5.00 quarter round in cement mortar 1:1 including Rmt

neat cement finishing, watering etc. complete.

187 2.00 Making Water connection from exi.Muni. Water No.

line (N.S.) 250.00

Applying and providing Expansion joint sealing

System on 100 mm vide joint including cleaning

exansion joint by mechanical means provision of

adhesive and flexible membrane with required

bond length as per menufracturer specification

188 2.00 and Smt

4mm thick alluminium strip covering with one

sloted and bolted with suitable system, inclusive

all manpower, machinery and material as per

specification and as directed.

Providing and Fixing 1 H.P. Electrical monoblock

or submarcible water pumps withmotor and

required cable and switch board of approved 6,800.00

brand and make etc.comp.as directed.

.Providing TMT Bar FE 415 reinforcement for

R.C.C. work including bending, binding and

placing in position complete up to floor two level 66.59

ProvidingTMTBarFE500/500Dreinforcement for

R.C.C.workincluding bending,binding and

placing in position complete upto floor two level

placing in position complete upto floor two level 75.46

placing in position complete upto floor two

level(upto 10 ton)

Providing and fixing 30mm thick solid both side

prelam PVC door shutter (sintex door-

equivalent) with necessary alluminium fitting with 2,214.00

EL-7 section frame

Providing & Fixing in position Alluminium window

sliding / fix type with frame using approved

anodised extruded alluminium section as

approved by Engg. In charge.(Jindal alluminium)

units equivalent (a) Frame sections 65 x 25 mm (

at 0.41 kg/mt) (b)Sliding Frame bottom section of

192 1.00 61.85 x 31.75 mm (at 0.41 Kg/Rmt) © Shutter Sq. M.

top & bottom section 40 x18 mm ( wt.

Kg/Rmt ) (d) Shutter interlock vertical section

x 18 mm.( 0.41 Kg/ Rmt) (e) Shutter vertical of

40 x 18 mm. (0.41 Kg/Rmt) including P/F

installing 5 mm thick approved color Acrylic

sheet of standard quality etc.comp.

Providing and laying polished granite stone slab

18 mm thick in risers of steps, dedo and pllars

laid on 10 mm thick cement mortar 1:3 (1

cement:3 coarse sand) and jointed with gray 2,690.00

cement slurry including rubbing & polishing

Wall panelling with 12 mm MDF fixed to

existing alluminium framing and making grove

194 2.00 as per design and finished with royal plastic Smt

paint as per instruction of engineer incharge.

Providing and laying 15mm bamboza

wooden flooring as per architect's drawing

with all necessary details as directed by

195 10.00 the project consultants. Use underlay for Smt

better result as per Detail specifications and

directed by the project consultants. (N.S.)

(Approved Rate )

Providing 20 mm thick double coat mala cement

plaster on interior brick / concrete work for

plastering comprising of base coat of 12 mm

thick cement plaster in cement mortar (1 Cement

: 4 coarse sand) in rough finishing and 8 mm 269.78

thick top coat of cement mortar 1:2 (1 Cement :

2 Coarse sand) finished with trovel including

scaffolding curing etc. complete.

Finishing wall with weather proof exterior

emulsion paint on wall surface (two coats) to

give an required shape evenshade after

thoroughly brushing the surface to remove all 113.40

dirt, and remains of loose powdered

materials.etc complete

High Back Chairs for vip Lounge

:Supplying and installation of “Revolving

High Back” chairs. The chairs must be

robust, ergonomically designed and

comfortable. Seat & Back Assembly -

1.2 cm thick hot pressed plywood and

upholstered with Fabric and Molded

Polyurethane Foam with PVC lining all

around. Back foam is designed with

contoured lumber support for extra comfort.

Chairs Dimension - Width 55 cm, Depth

cm Height 103 – 115.5 cm, Seat Height(SH)

44 – 56.5 cm. The Polyurethane foam should

be molded with density 45+/-2 kg/m3 &

Hardness = 16+/-2 kg/m3onHampden

machine at 25% compression. Arm Rest

- One-piece Black integral skin

polyurethane with 50-70 shore. `D’ Type Handle

and reinforced with MS insert. Centre

Pivot Mechanism - 360o revolving type 17o

maximum tilt on pivot at centre Tilt tension

adjustment. Upright locking. Telescopic

Bellow Assembly - The bellow should be 3 piece

telescopic type and injection molded in black

Polypropylene. Hydraulic Height Adjustment -

The Hydraulic height adjustment should be

provided with adjustment stroke of at least

10cms. Pedestal Assembly - The pedestal

should be injection molded in Black

powder coated MS on and fitted with 5 nos.

twin wheel castors. Twin wheel castors -

The twin wheel castors should be injection

molded in Black Nylon The complete

item as per architect /engineer in charge

Providing and supplying Medium Back

Chair for Control room MODEL LIKE

HOF OCT 172 Revolving synchro

tilting mechanism based chair with gas lift

for adjustable height and medium curved

back with seat and back PU molded cushion

with MS pipe frame structure and white

foam layer for seat and molded PU foam. White

foam layer for back covered with thick

199 3.00 cloth and draped with cloth of approved Each

shade. (min. of Rs.150/meter). 5 legged

revolving molded nylon chair base with good

quality of PU castors with 2 years replacement

guarantee. The chair to have wide polyurethane

arm rest of approved shape. Complete chair

should be in suitable shape. Rates to be

inclusive of all taxes and free delivery at

site. The complete item as per architect

/engineer in charge

Providing and fixing storage, entire unit to be

made from 19 mm th. and 12mm Ply with

1.0mm &. 8 mm th. Laminate. Shelves to be

made from 19mm Ply with both side

laminate. Rate shall include necessary

200 60.00 approved mortise locking systems, S S Smt

Handle pair 2" to 4" height and necessary

hardware. Over all storage to be completed

with necessary hard ware and accessories

completed as per drawing and design as

given by Architect.

Existing storage repairing and veneer on

top Providing and fixing of Louvers On Existing

d.c panel Providing and fixing 35mmthk.

Louvers shutter made up from Ghanateak

frame with 135x75mm and shutter frame as per

detail and fixing aluminum louvers which

is specified readymade powder

coated aluminum grill panel louvers .and 7,500.00

applying melamine spray polish all exposed

wood work. Overall door to be completed

with necessary hardware and

accessories completed as per drawing and

design as given by Engineer In

charge/Architect.

Providing and fixing flush door shutters,

solid core construction with frame of first

class hardwood with cross board and face

veneer or plywood face panels, with both side

1 mm laminate finishing including

anodized aluminum butt hinges with

necessary screws. Decorative type and

pine wood core anodized minimum 3 no

mm long aluminum butt hinges in flush door

202A 2.00 shutters with 2 no of brass holdfast 325 mm Smt

long 1 no brass tower bolt 250 mm long and

two no of 150 mm long brass door handle .

Decorative both side laminated Flush door

mm thick. with frame of 10 cm x 7 cmt

Indian teak wood frame including all

necessary fitting fixtures hardware screw

and adhesive etc fixing up to all lead and lift

height up to 45 mtr from GL etc complete as

per direction of engineer in charge

Providing and fixing 35mm thick factory made

moulded door shuter consisting of solid core

single leaf flush door of 30mm thickness, lipped

with 15mm (5mm x 3) thick x 30mm width on

one stiles and top rail and 10mm (5mm x 2) thick

x 30mm width on the other stilesand bottom

rails. The inner panel laminated with 2mm thick

termite proof, water proof and fire resistant

B 2.00 moulded PVC Smt

sheet with 2,4,6 raised panel design in different

plain and /or prelim colours on one side after

routing the moulded design on flush door and

2mm plain and/or prelim PVC sheet on other

side using rubber adhesive on flush door and

solvent cement adhesive on the PVC liping etc.

complete as per direction of Engineer in charge,

manufacture’s specification and drawing.

P/M/F chainlink jali 8'x4' size as per details

sketch & instructionof engineer in charge same

as lal darwaja garden pattern consisting of 3'dia.

M.S black pipe 'A' class 5'4" ht. fixed at 8'9" c/c

in C.C 1:2:4 block of 9"x9"x9" size chain link jali

of size 2"x2"x10 gauge fixed in 35x35x5 mm MS

angle frame 8'x4' size with MS flat of size 25x3 1,230.00

mm welded jali etc.comp.The jali is to be welded

to MS pipe with MS flat as instruction given.The

M.S pipe and the M.S angle frame are to be

painted one coat of primer and two coats of paint

as directed in line and level. (N.S)

Providing & Fixing masonary wall with porbandar

lachiya stone with well dressed grooveas per

directed by engg.in charge for foundation, plinth

or super structure level (above plinth level upto

floor two level) in cement mortar 1:5 (1-cement :

5-fine sand) incl.pointing the joint with white

cement and yellow oxide powder in proportion to

match stone colour the joints should be thread

grooved as per exi. lake stone pitching

(A) stone masonary wall/stone dressed single

faced (size 15"x8"x9") 8,990.00

(B) stone coping (size 15"x8"x4")

(C) stone coping (size 15"x8"x9")

(D) stone column (size 15"x15")

(E) stone column top (size 20"x20"x9")

Supplying and fixing of 300 mm-L x 150 mm-

B x 380 mm-H Kerb block for Footpath in M-

20 grade using 20 mm nominal size black

trap aggregate of Sevaliya/Timbaor

equivalent quality for pre-cast blocks,

reasonablyexposed finish/ formwork

, mould with well equippedwith vibratory

system for kerb stones of approved design

including curing, etc. complete, including

205 50.00 thecost of formwork etc. complete. The Rmt

rate shall also include necessary cutting

of asphalt, fixing the Kerbstones in line and

level on 5 cm thick sand bedding

withnecessary equipments and materials.

The rate shall also include the flush pointing

in CM (1:3) for all joints of thekerbstones. Filling

of zari alone the sides of the kerbstone fixed

with Bituminous concrete

Bituminousconcrete / C.C. mixed in proper

position to flush withthe road surface as

directed by Engineer in change to form a

portable mixture.a) Laying on 5 cm thick Sand

Providing and fixing pre-cast concrete kerb stone

of gray cement based concrete block 30cm

length,30cm height and 15cm thick of M200

b 25.00 grade concret as per approved design and Rmt

including excavation for fixing in proper line and

level,filling the joint with C:M 1:3 (1cement:3fine

sand) etc complete.

Providing and Laying of Rubber Moulded Paver

Block Grey/Coloured 60 mm thick, M-35 Grade

of any size shape (Usually Uni-Paver Blocks)

using black trap good quality aggragate of

mm nominal size for footpath,parking areas,

service lanes and other areas as mentioned in

the drawing / instruction of engineer in charge.

Cost includes formworks using rubber mould,

Rate providing and laying paver blocks as per

required grading and specification. The paver

block shall be mechanically compacted. The

work of paving blocks shall be executed in line 501.60

and level by skill mason of flooring work only. It

should be laid in such a way that the no cutting

of the paver block to be necessary. if cutting of

paver block necessary then it should be cut by

machine only and carting. The finished surface

of the paver block shall have resonably good,

plain finished. Paver blocks shall be compacted

and shall be relaid if necessary. Gravel or such

type of materials shall not be allowed for

production. Laying on 5 cms thick sand

Provoding and fixing flush door shutters, solid

core construction with frame of first class hard

wood with cross board and face veneer or ply

wood face panels, including anodised alluminium

butt hinges with necessary screws. (B) Non- 1,779.97

decorative type and block board core anodised

alluminium butt hinges in flush door shutters (2)

35 mm thick. Labour work for fixing any kind of

paving with cement pointing in CM 1:2, including

watering, ramming etc comp. as dir.For

I) Laying on Sand bedding as per requirement to

208 5.00 fix the C.C.Block / Nibhada Stone in Line & Level Smt

Box type metal letters forming composite box

made from 1mm thick stainless steel plate of

grade 304 having brush finish of following font

size to be fixed at Main Gate in english and or

Gujrati and including fixing charges approved

before fixing by clent / consultant.

Providing and fixing false ceiling at all height

including providing and fixing of frame work

made of special sections, power pressed from

M.S. sheets and galvanized with zinc coating of

120 gms/sqm (both side inclusive) as per IS :

277 and consisting of angle cleats of size 25 mm

wide x 1.6 mm thick with flanges of 27 mm and

37mm, at 1200 mm centre to centre, one flange

fixed to the ceiling with dash fastener 12.5 mm

dia x 50mm long with 6mm dia bolts, other

flange of cleat fixed to the angle hangers of

25x10x0.50 mm of required length with nuts &

bolts of required size and other end of angle

hanger fixed with intermediate G.I. channels

45x15x0.9 mm running at the spacing of

mm centre to centre, to which the ceiling section 850.00

0.5 mm thick bottom wedge of 80 mm with

tapered flanges of 26 mm each having lips of

10.5 mm, at 450 mm centre to centre, shall be

fixed in a direction perpendicular to G.I.

intermediate channel with connecting clips made

out of 2.64 mm dia x 230 mm long G.I. wire at

every junction, including fixing perimeter

channels 0.5 mm thick 27 mm high having

flanges of 20 mm and 30 mm long, the perimeter

of ceiling fixed to wall/partition with the help of

rawl plugs at 450 mm centre, with 25mm long

dry wall screws @ 230 mm interval, including

fixing of gypsum board to ceiling section and

perimeter channel with the help of dry wall

screws of size 3.5 x 25 mm at 230 mm c/c,

including jointing and finishing to a flush finish of

tapered and square edges of the board with

recomme-nded jointing compound , jointing

tapes , finishing with jointing compound in

layers covering upto 150 mm on both sides of

joint and two coats of primer suitable for board,

all as per manufacturer’s specification and also

including the cost of making openings for light

fittings, grills, diffusers, cutouts made with frame

of perimeter channels suitably fixed, all complete

as per drawings, specification and direction of

the Engineer in Charge but excluding the cost of

Providing and fixing wall acoustical paneling

using ecotone Slato/ Anutone slato or equivalent

Acoustic Panel make Slats L-16 of size

128mmx2430mmx16mm thick up to 2400mm

high as per the following specification :-Slats L-

16- 2mm @16mm, 32 x 128 x 2430 mm high

grade Pine wood base Medium Density Fiber

acoustic boards with Tongue & Groove

Edge,2mm slot perforation @ 16mm centre,

slates perforations, The acoustic should be

furnished with a Black absorbent felt backing

with an airflow resistance of 330- 460 Ns/m³

(DIN 53887),wood practical core,NRC : should 4,160.00

be Up to 0.75,should meet the safety

requirements of EN 14190. Fixing :- Sound Strut

CC18 screw fixed horizontal/vertical to wall at

every 600mm c/c. Metal cleat can be fixed on

top edges of Sound Strut CS55 fixed directly by

stamping to the CS55 and IC91 which is screw

fixed directly to the wall where ever required with

a backing black color fabric as approved by

Architect and as specified including all

accessories, material & labor complete as

directed by Architect / Engineer.

Providing & Fixing SPEED BUMP - #2 No (1

black, 1 yellow) 350 x 500 x 50 mm, Size per

color End Cape 350 MM x 175 MM x 50 MM

TOP DESIGN - Lining Top flat ANTI SKID

PATTERN FOR GRIP COLOUR :- YELLOW &

BLACK BODY MATERIAL :- MODIFIED

THERMOPLASTICS (Polymer Rubberized ) • 2,185.00

ECO FRIENDLY RECYCLE RUBBER Packing

:- 4 pcs/ woven Bag Load Capacity :- 20 MT

Fitting ( Fixing on TRAKE) :-4 holes & END

CAPE :- 2 HOLE HEX Bolts with Washer Epoxy

for Bolt Fitting etc. complete as directed by EIC .

Providing & Fixing in position 24 MM exposed

grid suspension system with “P “ Grid profile

false ceiling system using 600 MM X 600 MM

ecotone/anutone or equivalent make Glass Fiber

Ceiling Tiles having tegular edges & 0.90 NRC

value and approved surface design (with NRC of

0.90) and edge profile Tegular placed in a

suspended grid of size 600 MM X 600 MM made

from hot dipped GI Steel sections, rotary

stitched, main tee of size 24 X 42 X 3000 MM X

0.40 MM thickness suspended at every 600 MM

c/c along length of ceiling with 4 MM dia, Pre- 2,619.00

straightened G.I.Wire with necessary level

adjusters & intermediate cross tees of size 24 X

38 X 600 MM X 0.40 MM thickness shall be

inserted in to slots between the main tees at

MM centers in direction vertical to the main tees,

where in the main tees are resting on the

periphery on wall angles of size 24 MM X 24 MM

X 3000 MM X 0.40 MM thickness including

providing necessary openings for light fixtures,

Providing and fixing of Roller blind

curtain/blackout. The fabric shall be woven from

formulated platisol extruded over a polyaster

yarn.The fabric shouldl be weaved to provide

subtle view of the side of the blind and should 2,610.00

offer elimination of glare and sunlight radiance

upto a minimum of 80%.The fabric shall be flame

Providing and applying Texture Paint (Rustic

Finish) on external plastered surfaces, pattern

as per sample approved by the Architect.

including preparing surface, using roller to get

approved texturised surface. Job to include

making required surface preparation, to receive

Texture paint finish etc. All complete as per 425.00

detail drawing, as specified and as directed by

Architect / Consultant / Project - In - Charge. The

rates shall be inclusive of Scaffolding, all

material, labour etc. complete. as directed by

Providing and fixing PVC/Gpsysum plain colour

false ceiling with grid type with aluminium

frame from gypsteel, fastners ,props, Finishing

as per architectural drawing allowing

216 2.00 openings for A.C. Diffusers, Smt

Light/Electrical Points etc –complete, Prior to

fixing on frame.(Brand : Anutone or

equivalent ) (N.S.) or as directd by engineer In

Provdg. & laying S.W. Gully trap with brick

masonry chamber & water tight G.T.Stone

including fixing of covervSquare mouth trap 100 1,279.40

mm x100 mm size P-Trap

Providing cement vata (10cmx10cmsize) quarter

218 50.00 roundin cement mortar 1:1 including neat Rmt.

cement finishing, waterin getc. complete.

Providing and laying (to level or slopes) and

jointing with stiff mixture of Cement Mortar in

219 5.00 proportion 1:1 Salt glazed stoneware pipes Rmt.

including testing of pipes and joints complete.(A)

Providing and laying (to level or slopes) and

jointing with stiff mixture of Cement Mortar in

220 10.00 proportion 1:1 Salt glazed stoneware pipes Rmt.

including testing of pipes and joints complete.(B)

Constructing brick masonry chamber for

underground C.I. Inspection chamber and bends

with bricks having crushing strength not less

than 35Kg/Cm2 in C.M. 1:5 C.I. cover with frame

(Light duty) 455mm x 610mm intenal dimensions

total weight of cover with frame to be not less

than 38Kg. (Wt. of cover 23 Kg.) and Wt. of

221 10.00 frame 15Kg. ) (R.C.C. top slabe with 1:2:4 mix Each

(1-cement :2- coarse sand :4-graded stone

aggregate 20mm size) foundation concrete

1:5:10 inside plaster 15mm thick with cement

mortar 1:3 finished smooth with a floating coat of

neat cement on walls and bed concrete etc.

complete.(i) Inside dimensions 455mmx 610mm

and 450mm deep for single pipe line.

Constructing brick masonry chamber for

underground C.I. Inspection chamber and bends

with bricks having crushing strength not less

than 35Kg/Cm2 in C.M. 1:5 C.I. cover with frame

(Light duty) 455mm x 610mm intenal dimensions

total weight of cover with frame to be not less

than 38Kg. (Wt. of cover 23 Kg.) and Wt. of

frame 15Kg. ) (R.C.C. top slabe with 1:2:4 mix

(1-cement :2- coarse sand :4-graded stone 3,624.51

aggregate 20mm size) foundation concrete

1:5:10 inside plaster 15mm thick with cement

mortar 1:3 finished smooth with a floating coat of

neat cement on walls and bed concrete etc.

complete.(i)Inside dimensions 500mm x 700 mm

and 450mm deep for pipe line

with one or two inlets.

Constructing brick masonry chamber for

underground C.I. Inspection chamber and bends

with bricks having crushing strength not less

35Kg/ Cm2 in C.M. 1:5 C.I. cover with frame

(Light duty) 455mm x 610mm intenal dimensions

total weight of cover with frame to be not less

38Kg. (Wt. of cover 23 Kg.) and Wt. of frame

222A 10.00 15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1- Each

cement :2- coarse sand :4-graded stone

aggregate 20mm size)

foundation concrete 1:5:10 inside plaster 15mm

thick with cement mortar 1:3 finished smooth

with a floating coat of neat cement on walls and

concrete etc. complete.(iii) Inside dimensions

600mm x 850 mm and 450mm deep for pipe

lines with three or more inlets.

Providing, supplying and fixing precast C.C.

blocks (M-20) edge kerb having size of 75 x

x 300 mm depth and as per design conveying it

to the site, jointing into C:M 1:3 and racking out 219.00

the joints incl. necessary excavation of asphalt,

soil etc..completed.

Constructing a cooking Sandwich platform

cm. width and 70 cm high resting on

B.B.Masonry walls23 cm.thick in C.M.(1:6) with

(ii) Fixing black Granitee 30mm thick laid on 933.98

precast R.C.C. (1:2:4) slab with plastering on

exposed faces of wall in C.M. (1:4) etc complete.

Constructing a cooking platform 60 cm. width

and 70 cm high resting on B.B.Masonry walls

cm.thick in C.M.(1:6) with (ii) Fixing black

kadappa stone 30mm thick laid on precast 1,132.43

R.C.C. (1:2:4)slab with plastering on exposed

faces of wall in C.M. (1:4) etc complete.

Providing and fixing hard drawn steel wire fabric

75mm x 25mm mesh or weight not less than

7.75 kg. per Sq.M. to window frames etc. 754.65

including60 x 20mm beading of teak wood.

Providing & fixing 15 cm wide chicken mesh jali

with nails & then application of 15 mm plaster on

R.C.C.& masonary joints as per dir.of engg.in 35.00

Providing and laying cement concrete flooring

1:2:4 (1-cement : 2-coarse sand : 4-graded

227 10.00 stone aggregate 20mm nominal size) laid in one

layer and finished with a floating coat of neat

cement. (A) 50mm thick.

Providing and constructing, Underground (U/G)

water tank of specified capacity, on specified

location, for all depths, in controlled CC of M-200

grade with bottom slab, top slab and RCC walls,

including cost of form work and

reinforcement,with inside and outside plaster in

228 25000.00 CM 1 :3 and water proofing treatment as per

IWP specification,including injection, grouting,

etc. complete. The rate includes for providing

and fixing two nos. 0.6m. x 0.6 m. size medium

duty CI manhole cover/s at top, including wash

out pipe line and inlet and outlet connections etc.

Providing & Fixing of Armstrong Mineral Fibre

Acoustical Suspended Ceiling System with Dune

(Bevelled Tegular) Edge Tiles With Armstrong

15mm Exposed GRID. The tiles should have

Humidity Resistance (RH) of 99%, NRC 0.5,

Light Reflectance ≥85%, Thermal Conductivity k

= 0.052 - 0.057 w/m K, Colour White, Fire

Performance UK Class 0 / Class 1 (BS 476 pt -

&7) in module size of 600 x 600 x 15mm

suitable for Green Building application, with

Recycled content of 32%. The tile shall be laid

on Armstrong Silhouette profile grid system with

229 10.00 15mm white flanges incorporating a 6mm central

reveal in white/black colour and with a web

height of 45mm and a load carrying capacity of

minimum 15.68 Kgs/M2 & minimum pull out

strength of 100 Kgs.. Silhouette, Main Runners

& Cross Tees to have mitred ends &

“birdsmouth” notches to provide mitred cruciform

junctions. The T Sections have a Galvanizing of

90 grams per M2 and need to be installed with

Suspension system of Armstrong make.

Warranty Certificate and Test Reports for NRC,

CAC and Fire rating shall be provided by

Mineral Fibre Acoustic Modular Ceiling Tile

should be GREENPRO certified and qualifies as

GREEN PRODUCT certified by CII Green

Products and Services Council.INSTALLATION:

To comprise main runner spaced at 1200mm

centres securely fixed to the structural soffit

using Armstrong suspension system

(specifications below) at 1200mm maximum

centre. The First/Last Armstrong suspension

system at the end of each main runner should

not be greater than 450mm from the adjacent

wall. Flush fitting 1200mm long cross tees to be

interlocked between main runners at 600mm

centre to form 1200 x 600 mm module. Cut

cross tees longer than 600mm require

independent support. 600 x 600mm module to

be formed by fitting 600mm long flush fitting

cross tees centrally between the 1200 mm cross

tees.Perimeter trim to be Armstrong wall angles

of size 3000x19x19mm, secured to walls at

mm maximum centres. Installation should be

carried out as per Armstrong recommended

procedure.ARMSTRONG SUSPENSION

SYSTEM accessories manufactured and

supplied by Armstrong World Industries

consisting of M6 Anchor Fasteners with Vertical

Hangers made of Galvanised steel of size 26 x

26 x 25 x 1.2mm with a Galvanised Thickness of

80gsm, A pre Straightened Hanger wire of dia –

2.5 mm of 1.8 m length., thickness of 80gsm and

a tensile strength of 344-413 MPa, along with

Adjustable hook clips of 0.8mm thick, galvanised

spring steel for 2.68 mm with a minimum pull

strength of 110 kg. The adjustable clip also

consists of a 3.5 mm aquiline wire to be used

with the main runner.

Providing and fixing PVC Printed pain colour

false ceiling with grid type with alluminium frame

consisting of 600mm x 600mm 3mm thick plain

PVC sheet used as panel insert in a frame work

made using anodized alluminium T section of

size 1 x 1 (235 x 25mm, 19 gauge or 1 mm thick)

in square pattern of grid sizes of 2 x 2 (600 x

600mm) The alluminium frame work is supported

230 10.00 from the cceiling with the help of G.I. hook and

G.I. wire/6mm M.S. rods of required sizes to

maintain proper level etc. The aluminium frame

work is supported on side wall with the use of

alluminium L section of size 1 x1 (25 x 25mm)

angles etc. complete as per direction of Engineer

in charge. Manufactures specification and

Providing and supplying of labour for necessary

manual excavation, cleaning, Shifting of Material

231 15.00 Or any other, or for any other work as directed

by Engineer In charge. The Rate includes

Handcart with Mazdoor

Fitter/Plumber/Mason

WELDER/ Gas cutter at Day /night

Supplting of welding machine / gas cutter

including cost of welding rods/gas,

D 5.00 Transportation, including carting from site to

Mazdoor at Day Male/Female

Conveyance charges of (A) limemurrumbuilding

rubbish earth manure or

232 200.00 sludge & execavated rock andrubbish

[Limemurrum building rubbish

Supplying electric breaker machine for RCC slab

or asphalt demolishing work on site by using

operator, fuel, power supply etc.complete as

directed. (no payment should be allowed for non

233 1.00 working condition of machinery and for pipe line

excavation and M.H. work. Allowed only for

break down work) (Based on Previously

approved rate by CE sir )

CatchPit Jali Fixing P/F FRC catch pit jali with

frame 600mm x 600mm clear opening etc.

234 5.00 comp. As directed by engineer in charge. (Based

on Central Store Rate)

Providing and fixing concealed center point to

wall ceiling & floor CPVC (SDR 13.5) PIPE

having National Sanitation Foundation (NSF)

235 seal for potable water of following dia. nominal

bore tube fittings and clamps including making

good the wall, ceiling and floor etc. complete.

Providing and fixing cast iron steps of size

236 10.00 500mm x 150mm x 22.5mm and painting with

two coats of Anti-corrosive paint etc. complete.

Supplying and fixing C.I. cover 300mm x 300mm

237 10.00 without frame for Gulley trap (Standard pattern)

te weight of cover to be not less 4.53 Kg.)

Providing and fixing to wall ceiling and floor

10.0Kg.F/Cm2 working pressure polythene

pipes of the following out side Dia.

238 Low densidy, complete with special falnge

compression type fittings, wall clips etc.

including making good the wall ceiling and

Providing and fixing sheet glass, selected quality

(Type-C) bedded in putty and fixed withwooden

239 10.00 beading including the cost of wooden beadings

of first class teakwood and necessary cutting of

glass. (2) 6 mm thick.

Providing and fixing rough cast wired glass,

6mm thick bedded in putty and fixed with

240 10.00 wooden beading including the cost of wooden

beadings of Indian teak wood and necessary

cutting of glass. (C) Wired - figured glass

Providing and fixing five courses water profing

treatment with bitumen felt consisting of second

and fourth course of blown / bitumen or/ and

residual bitumen applied hot at 1.2 kg.per

Sq.M.of area for each course and first course

with fibre base bitunen saturated under lay type

land third course

241 20.00 with fibre base self finished felt type 2 grade 1

fifth and final course of stone grit 6mm and down

size or pea sizes gravel spread at 0.008 Cu.

Metre / Sq. metre

including preparation of surface excluding

grading complete.

Providing and fixing three courses water profing

treatment of Astral Make Company. with an first

layer of first course with fibre base, Second

Course of Water Proofing chemical coat, and

Third Coat of Fibre Coat with fibre base self

242 20.00 finished felt type 2 grade 1 and final course of

Burshing with chemical Treatment with a

thickness of 1 to 2 mm thickness, including

preparation of surface , The Said work should be

provided for a perfomance bond of 5 Years for

warranty purpose.

Constructing Manhole with R.C.C. top slab in

1:2:4 mix (1-cement :2-coarse sand : 4-graded

stone aggregate 20mm nominal size) foundation

concrete1:3:6 mix (1-cement : 3- coarse sand :6-

Brick bats 40 + 50mm size) inside plastering

15mm thick with Cement Mortar 1:3 (1-Cement :

3-coarse sand) finished with a floating coat of

neat cement and making channels in cement

concrete 1:2:4 mix (1- Cement :2-Coarse sand

:4-stone aggregate 20mm nominal size) finished

243 5.00 smooth complete including curing and festing (i)

Inside size 900mm x 1200mm

and 1.5M. deep including C.I. cover with frame

size 560mm diameter total weight of cover and

frame to be not less than 128 kgs. (Wt. of cover

64 Kg. and Wt. of frame 64 Kg.)(A) With 230mm

thick walls of brick msonry using brick having

crushing strength not less than 35Kg. / Sq.cm. in

Cement Mortar 1:5 (1- Cement: 5-Coarse sand)

(1) A type depth 0.90 Metre for 150mm diameter

Providing and fixing of wall paper at Wall/Ceiling/

or at other places, as required. ( Basic Rate of

244 5.00 Wall paper must be (100-120) Rs. Per Sq.Ft.

The Rate includes of necessary material, with

fixing and transporation with necessary solution.

Providing and fixing of Shower of jaquar make

245 5.00 for Serial No. 0797N ALD ( High Flow C/Body-

Jaquar, Primary Batch )

Providing and fixing of Metro Pole of 40 mm dia

246 5.00 of Jaquar Make of series FLV-1093 N ( Serial

Providing and fixing of chair bracket for Support

247 5.00 of W.C. of Primary batch Series-7324 of Jaquar

Providing and fixing of upper part of W/C of

248 5.00 jaquar series of 8481

Providing and fixing of 2 in 1 Bib cock of jaquar

249 5.00 Series of KUP-35041 (8481) as per Instructions

of engineer in charge.

Providing and fixing of Pillar cock of jaquar make

250 5.00 series EXTND 190 MM as per instructions of

engineer in charge.

Providing and fixing of Angle cock of jaquar

251 5.00 make series of KUP-35053 PM

Providing and fixing of shower of size 8x8m

including shower arm, flange, floor trape,

252 5.00 including all material with fixing as per

Instructions of engineer in charge.

Supplying and fixing of Roller blind curtain In

Patterned Fabric of Different Textures corded in

roller blinds with stiching fittings and of stichles

253 5.00 pattern. The Price Rate Includes necessary

Making with fixing of roller blind with roller

mechanism as instruction and selection of

design as per engineer in charge.

Supplying and fixing of Sheer Curtains of

Different Size, In Patterned Fabric of White

Colour Textures stiching fittings and of stichless

254 5.00 pattern. The Price Rate Includes necessary

Making with fixing of Sheer Curtain with top

channels of fixing as instruction of engineer in

Supplying and providing of Green Curtain for

prevention of Sunlight. The Price Rate Includes

blackout curtains with dense or fabirc or foam

255 5.00 interlining material. The Price Rate also Includes

necessary fixing with roller tie ropes at site at

any height as per instruction of engineer in

Demolition of Existing Platform and Construction

of New Modular kitchen with necessary drawer

Arrangement, Providing and fixing of chimney,

and Providing of Self for Placing of utensils, with

tandom channels, Laminates in hard board

material. The Rate also includes construction of

Platform in Granite work, including kitchen sink

256 1.00 and with necessary Plumbing work, as per

Instructions of engineer in charge. The Rate

includes with necessary materials of hardware,

manpower, necessary machinery for platform

work and other civil works upto any lead and lift

as directed. The Rate also includes carting of

materials for to and fro at the site.

Supply & fixing factory finished cold formed Light

guage steel frame sections confirming to SP:6

(5) 1980 at site or work including riveted, bolted

or welded in builtup for all type of sections ,in

257 750.00 framed work, cutting, hoisting, fixing in position

applying primer coat of approved steel primer

etc. complete as per structural designs &

directions of Engineer-in-charge.

Providing valleys 900mm overall in plain 1.6mm

258 2.00 thick G.I. sheet fixed with G.I. J or L Hooks, Bolts Smt

and nuts glavanised iron J or L Hooks Bolts and 1,042.78

nuts 8mm dia G.I. Limpet and bitumen washers

Providing laying (to level or slopes) and jointing

reinforced concrete Light duty non-pressure

pipes I.S. class NP2 of the following internal

259 2.00 diameter with collars and butt ends prepared for

collar joints including testing of joints

complete.(D) 300mm

Constructing Manhole with R.C.C. top slab in

1:2:4 mix (1-cement :2-coarse sand : 4-graded

stone aggregate 20mm nominal size) foundation

concrete 1:3:6 mix (1-cement : 3- coarse sand

:6-Brick bats 40 + 50mm size) inside plastering

15mm thick with Cement Mortar 1:3 (1-Cement :

3-coarse sand) finished with a floating coat of

neat cement and making channels in cement

concrete 1:2:4 mix (1- Cement :2-Coarse sand

:4-stone aggregate 20mm nominal size) finished

260 1.00 smooth complete including curing and festing (i)

Inside size 900mm x 1200mm and 1.5M. deep

including C.I. cover with frame size 560mm

diameter total weight of cover and frame to be

not less than 128 kgs. (Wt. of cover 64 Kg. and

Wt. of frame 64 Kg.)(A) With 230mm thick walls

of brick msonry using brick having crushing

strength not less than 35Kg. / Sq.cm. in Cement

Mortar 1:5 (1- Cement: 5-Coarse sand) (2) B

type depth 1.50 Metre for 150mm diameter

Providing laying (to level or slopes) and jointing

reinforced concrete Light duty non-pressure

pipes I.S. class NP2 of the following internal

261 9.00 diameter with

collars and butt ends prepared for collar joints

including testing of joints complete.(D) 300mm

ELECTRICAL WORKS:-

Point wiring for secondary light point with 2-

1.5 sq.mm & earthwire of 1.5 sq.mm (green)

both are of ISI marked 1.1 KV grade FRLS

PVC insulated multistrand copper wires, in

following type of pipe to be erected

concealed in / flushed on wall/ceiling, complete

with earth continuity and necessary 120.00

connection with primary light with accessories

erected on Metal / PVC box covered with

mm thick PC(Polycarbonet) / Acrylic sheet for

open / concealed wiring.with necessary Lamp

holder / ceiling rose / H.D.Connector as

directed.(a) with medium class Rigid PVC

pipe and accessories.

Providing and laying 4.0 sqmm circuit

2 1.00 wiring with 2.5 sqmm earth wire of green color Rmt.

Point wiring for secondary light point with 2-

1.5 sq.mm & earthwire of 1.5 sq.mm (green)

both are of ISI marked 1.1 KV grade FRLS

PVC insulated multistrand copper wires, in

following type of pipe to be erected

concealed in / flushed on wall/ceiling, complete

with earth continuity and necessary

connection with primary light with accessories 120.00

erected on Metal / PVC box covered with

mm thick PC(Polycarbonet) / Acrylic sheet for

open / concealed wiring.with necessary Lamp

holder / ceiling rose / H.D.Connector as

directed.(a) with medium class Rigid PVC

pipe and accessories.

Providing and laying 4.0 sqmm circuit

4 1.00 wiring with 2.5 sqmm earth wire of green color Rmt.

Suppling and laying Cat 6 lan cablel of d-

5 1.00 link or equivalent make etc. complete. (N.S.) Rmt

Mains with 1.1 KV grade FRLS PVC

insulated ISI marked stranded Copper

conductor wire in following type of pipe to be

erected concealed in /flushed with

6 wall/ceiling, with 1.5 sq. mm copper

conductor FRLS PVC insulated stranded

wire of green colour for earth continuity

of following size. (a) with medium class

Rigid PVC pipe and accessories.

(a) 2 wire 1.5 sq. mm.

(b) 2 wire 2.5 sq. mm.

(c) 3 wire 1.5 sq. mm

(d) 3 wire 2.5 sq. mm

(e) 4 wire 1.5 sq. mm

F 1.00 (f) 4 wire 2.5 sq. mm Rmt

(g) 6 wire 2.5 sq. mm

Supplying & erecting Delton or approved

make Telephone Cable electrolytic copper

conductor PE insulation twisted in two pairs,

& wrapped with FRLS PVC tape & sheathed

with FRLS PVC or HFFR outer Jacket suitable

for telephone wiring & confirming to C-DOT

erected in existing pipe. of following

size of conductors & nos.of pairs. With

necessary connections. (N.S.) [A] Conductor

Size 0.5 mm (a) Unarmoured

Call bell point with push button switch

Providing following type of Modular Type

Accessories mounted with pvc / metallic box,

single mounting base frame covered with

textured / metallic front plate , modules

erected with necessary connection.

As desired by Engineer Incharge

(1)One No. SP 6 Amp. Cat.III

(2) One No 5 pin plug.Cat. III

(9) 16 Amp. SP one way switch.Cat.III

(10) 6/16Amp. Universal

socket.Cat.III 200.00

Supply, Installation, testing and

commissioning of Surface mounted

light fixture suitable for 2 X 18 W luminaire

along with all other necessary

9 1.00 accessories. (PHILIPS / Equlent Cat :-Green No.

LED Square, type:

910403630906,Product descrption : BBS182

1XDLED- 5000 PSU WH) BASIC PRICE:

Supply , Installation, testing and

commissioning of pre-wired, fluorescent

fitting / compact fluorescent fitting/LED

fitting/MH fitting/post top luminaries etc of all

types, complete with all accessories

and tube etc. directly on ceiling/ wall,

including connection with 1.5 sq. mm FRLS PVC

insulated, flexible, copper conductor, single

core cable with flexible conduits and coupler

and earthing etc. as required

Supply,Installation,Testing and

Commissioning of 2'X2' LED LIGHT

PANEL of following Cat No. (1) RECESS

MOUNTING :- Philips RC 365B /

Crompton LCPL-36-CDL /Bajaj BZRS QL

W XL / Wipro LM17-411--XXX-XX- XX- 40 W

(2) SURFACE MOUNTING :- Philips SM 5,800.00

365C / Crompton LCPL-36-CDL / Bajaj

BZSSQL X 36 W XL / Wipro LM17-411--XXX-

XX-XX- 40 W Contractor has to supply

Colour i.e. Warm white/ Cool White as

per Client requirement.

Supplying & erecting 1 X 20W surface

mounted LED Patti light fixture with driver

and all accessories as approved by client /

11 5.00 consultant. (Ref make- PHILIPS make TMS No

501 / 1 x TLED 20w Luminaire suitable for

TLED 20w with 20w LED Tube) or equivalent of

Supply and erecting integral flood light with

driver inside a PDC housing Philips make

UNIFLOOD Cat.no: BVP120LED 70CWNB FG 9,890.00

S1 PSU GR or equivalent of Wipro or LG make

Supply, Installation, testing and

commissioning of Surface mounted

13 5.00 light fixture suitable for 2 X 18 W luminaire No.

along with all other necessary

accessories. Brand approved by eng. inch.)

Providing & erecting Approved make

Power Saving 50 Watt Ceiling Fan with

double ball bearing ISI mark with Condenser

230 volt A.C. 50 Hz 1200 mm sweep

complete having 3blades with aluminium

blades with , canopy & suitable lenght of 2,070.00

down rod erected with 24/ 0.2, 3 core flexible

wire with earthing.(Make shall be approved

by Engineer in charge))Orient energy star,

Havells ES-50,Crompton high speed +

Supplying and erecting approved make

oscillating type bracket fan A.C. 23OV. 50cy/s

400/450 mm sweep wall mounted with height

15 5.00 adjustment and rotary tilting device complete No

with guard, flexible Core plug top complete

erected with lead wires as directed.( Crompton,

Usha, Orient make only )

Supplying & erecting approved make low

noise decorative exhaust fan having size

16 5.00 200mm with 1350 RPM with square frame ABS No

body with inbuilt lowers & square

frame.(Crompton , USHA make only )

Providing and erecting 3 star and approved

make split air-cond consisting of

condensing unit wit hermetically sealed

rotary com accessories etc. duly

connecte erected evaporating unit and blower

17 5.00 accessories by means of proper ins tubing up No

to 5 RMT suitable for ( M.S. Stand, Gas

Charging & Int Wiring & Remote Control)

Makes :-3 of DAIKIN/O GENERAL / TR

/MITSUBISHI AND 5-star model of with cu

condensor for (b) 1.5 ton cap

Extra charges for the Items beyond standard

length For Single phase Split A.C. Machine

18 5.00 insulated pair of soft, copper tubing including Rmt

power and control cable up to 1.5 TR

Providing Approved make Triple Pole Metal

Clad Switch Fuse Unit 415/500 V. with HRC

fuse of suitable load and neutral link 6,790.00

confirming to IS 100 A/125 A

Approved make ELCBs / RCCBs conforming

to IS: 12640 and having sensitivity of

mA and Short Circuit withstand capacity of

KA and suitable for operation on single phase

20 1.00 240 V. having characteristic of quick Ea.

action & tripping with all advance feature & do

not incorporate any electronic component.

for following Max. rating erected as

directed (ii) 40Amps. DP Cat. III

Providing and erecting Sheet Steel powder

coated MCB distribution board - flush /

surface mounted fitted with busbar, neutral

link, earth bar and DIN rail, confirming to IS

21 1.00 13032 and BS 5486-1986 without MCB to Ea.

house appropriate nos. of MCBs.(The DBs

should be used of same company of MCB to be

used) (L) Three phase 6 way SS Double door

for single phase outgoing horizontal box

Providing Approved make Triple Pole Metal

Clad Switch Fuse Unit 415/500 V. with HRC

fuse of suitable load and neutral link 9,360.00

confirming to IS (a)200 A Cat.III

Existing A.C. Removing

Dismantling Existing Cup board

Dismantling of Necessary Existing Electrical

works 20,000.00

Primary light points controlled by one 6A

switch 1,350.00

27 1.00 Secondary light points controlled by one 6A No.

Supply, fixing, connection and testing of

5-pin 16 A power plug socket alongwith 16A

28 10.00 switch with top cover plate, PVC back box No.

suitable for modular plate with all accessories

to complete the job. (N.S.)

Supply, fixing, connection and testing of

5-pin 6 A power plug socket alongwith 6A

switch with top cover plate, PVC back box

suitable for modular plate with all accessories