REPAIR/MAINTS OF DRAINS, CULVERTS, BOUNDARY WALLS, HARDSTANDING AND PATHS ETC IN OTM ACCN IN SOUTHERN SECTOR UNDER AGE B/R-II AREA AT MIL STN KOTA

Amount

Taking down cement plaster of any description and thickness on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for like MH cover etc and removal all rubbish material outside of MoD land complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floor and pavings n.exc 15 cm thickness (below or above GL) and removal all rubbish material outside of MoD land complete all as specified and directed.

Demolition of brick work/stone boulder masonry, built in CM incl all quoins, arches, pillars etc but excluding ashlar facing, dressed stone work and precast concrete articles, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed.

M&L brick work with pulverized fuel Ash-lime bricks (Fly ash bricks - non modular size), straight or curved on plan exc 6 m mean radius, built in CM 1:6, complete all as specified and directed.

M&L walling of random rubble, uncoursed well bonded, bedded and solidly hearted, built in Cement Mortar 1:6, including finishing the joint, flush as the work proceeds complete all as specified and directed.

M & L for walling of random rubble, except stone i.e. using old serviceable stone obtained from demolition under serial item No. 4.00 (here-in-before), uncoursed well bonded, bedded and solidly hearted, built in Cement Mortar 1:6, including finishing the joint, flush as the work proceeds complete all as specified and directed.

Extra over sand stone walling for hammer dressing to face stones and dressing of face beds and joints, as specified, of random rubble walling, uncoursed or brought upto courses, with maximum depression on face from straight edge held against the dressed surface not exceeding 40 mm; to block in course masonry, complete all as specified and directed.

M&L Providing cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed.

M&L for providing precast cement concrete 1:2:4, type B-1 using 20 mm graded stone aggregate as in landings, cover slabs (for manholes etc), chajjas, water troughs, mangers, shelves and similar articles with plain faces including necessary formwork, set in CM 1:4, complete all as specified and directed.

M & L for providing cement concrete 1:2:4 type B-1 using 20 mm graded crushed stone aggregate as in surface channels and drains and benching & including finishing the top of benching even and smooth using extra cement complete all as specified and directed.

M & L for reinforced cement concrete 1:1.5:3 type A-1 using 20 mm graded crushed stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Form work (fair finished surfaces) to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.

M&L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, slabs, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality confirming to TMT bars complete all as specified and directed.

S&F in renewal of 2mm thick fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof, wall etc complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4, surface finished even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 15 mm thick on stone masonry surfaces or other than fair faces of brick work in cement mortar 1:4, surface finished even and smooth without using extra cement, complete all as specified and directed.

M&L for preparing newly plastered walls surfaces and applying two coats of cement base paint over and including a coat of primer complete all as specified as mentioned in note of the item and directed by Engineer-in-Charge. Note :- Steps to be followed for cement base paint :- Colour scheme of cement base paint passed by GE. (a) Curing the newly plastered surface of wall by spray gun. (b) Applying one coat of primer. (c) applying one coat of cement base paint (d) curing of surface by spray gun (e) Applying second coat of cement base paint after that curing of surface by spray gun.

M&L preparing old surfaces of walls, plastered or unplastered by brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots and applying one coat of cement base paint on walls by qualified painter & including cornices, pillasteres complete all as specified & as directed. Note :- Steps to be followed for cement base paint (a) Colour scheme of cement base paint passed by GE. (b) Filling of cracks by sika creem 888 group / doctor fixite crack filler or equivalent. (c) Curing of surface by spray gun (d) applying one coat of cement base paint (e) curing of surface by spray gun.

M&L for complete removal of existing treatment on walls by water jet/spray gun and brooming down or steel wire brushing/steel patti scrapping downn loose treatment, smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots and preparation of old plastered surfaces and applying two coats of cement base paint including a coat of primer by qualified painter complete all as specified as mentioned in note of the item and directed by Engineer-in-Charge. Note :- Steps to be followed for cement base paint. (a) Colour scheme of cement base paint passed by GE. (b) Complete removal of existing treatment by water jet/spray gun. (c) Filling of cracks by sika creem 888 group/doctor fixite crack filler or equivalent. (d) Curing of surface by spray gun (e) Applying one coat of primer (f) Applying one coat of cement base paint (g) Curing of surface by spray gun (h) Applying second coat of cement base paint after that curing of surface by spray gun.

M&L for preparing new steel surfaces exceeding 10cm width or girth and applying two coats of synthetic enamel paint over and including one coat of red oxide zinc chrome primer, complete all as specified and directed.

M & L for PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

S & F for mild steel work of angle iron or flat iron etc for hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts ; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

S & F of galvanised 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. (each line of wire to be measured) & including dismantling of old wire fencing complete all as specified and directed.

Re-straining, resecuring and including making good staples to galvanised 2 strand steel barbed wire any dia barbed with 2mm dia barbs at 75mm spacing and in any position etc complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors etc, laid, bedded and pointed in any mortar, complete all as specified and directed.

Dismantling of stone sett paving of any description or thickness, laid dry complete all as specified and directed.

M&L for PCC 1:3:6 type C-1 (using 20mm graded stone aggreate), 75 mm thick as in plinth protection/Path/PCC paving etc including finishing the surface even & smooth without using extra cement, with and including all necessary form work to divide the area in panels, finishing exposed edges fair or rounding or chamfering where dirtected and providing 6 mm wide joints throughout the thickness of plinth protection duly filled with mastic filling (one part of hot bitumen 85/25 and three parts of fine sand by weight), complete all as specified & directed.

M&L for machine pressed precast concrete interlocking paver block (glossy finish) any shape and size made with grey cement and pigment, confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade, laid over and including 25 mm thick sand cushioning, complete all as specified and directed.

M&L chequered cement concrete tiles 25 cm x 25 cm x 25 mm thick, set jointed and pointed in neat cement slurry with grey cement and pigments as in floors, laid over and including 20 mm thick screed in CM 1:6, complete all as specified and directed.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed.

M&L for 50mm thick PCC 1:2:4 mix type B1 (Using 20mm graded crushed stone agg) as in flooring, finishing surfaces even and smooth without using extra cement, complete all as specified and directed.

RAGHAV ENTERPRISES (BID ID -3084699)

S.S ENTERPRISES (BID ID -3085749)

SINGH ENTERPRISES (BID ID -3085023)

M/S MOHINI ENTERPRISES (BID ID -3085609)

ANNAPURNA ENTERPRISES (BID ID -3084633)

Ganesh Contruction (BID ID -3084785)

Aditya Enterprises (BID ID -3086173)