Providing and Erecting to LED Flood Street Light Fittings for TRC Garden to Smashan Bhumi at Ukai

Name of work:- Providing and Erecting to LED Flood Street Light Fittings For TRC Garden to Smashan Bhumi at Ukai

Sr.No Qty Item Rate Rate in Words Per Amount

Replacing Old and u/s by Supplying and erecting Flexible PVC insulated

1 multi strand multi core 1.1 kv grade ISI marked copper wires of following

size to be erected as directed.

(e) 1.50 Sq.mm 3 core round PVC sheathed

Rupees FiftyEight Paise

FiftyEight Only

Replacing Old and u/s by Supplying and erecting LED street light /

Flood light fittings with High power White LEDs wattage of 3 Watt

and above assembled on single MCPCB, efficiency more than

lm/w and corrosion free High pressure die cast aluminum housing

with smooth finish powder coated and heat sink extruded aluminium

with diffuser and Polycarbonate optics/ lenses, with toughened

glass with company mark/name engraved or embossed 160 to

V,Power Factor more than 0.95, THD < 10 %, CCT 3000 K to

5700K,Uniformity ratio >0.45, Luminaire efficacy> 100 lumens/watt .

LED driver efficiency > 85 %.( fittings required LM-79 & LM-80

certificates)(NOTE: Below description have shown ranges of

Wattage capacity of LED fittings.The Engineer incharge may select

any wattage capacity between the ranges shown.)

(A) Street Light (IP-65), Surge protection -4KV integral and ,Light

must have 440VAC line supply with over-voltage protection.

(iii) 60 - 89 watts

Rupees Five Thousand Eighty

Paise Thirty Only

Replacing Old and u/s by providing and erecting Miniature circuit

breaker single pole 6A to 25A suitable to operate on 240 V A.C. Rupees One Hundred

3 90 system and having breaking capacity 10 KA to be erected in 123.22 TwentyThree Paise TwentyTwo Ea

existing box. confirming to IS 8828/1996 with ISI Mark (B) cat-(III) Only

Replacing Old and u/s by Providing and erecting XLPE (IS:7098)(I)-

88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV.

4 to be laid on wall with necessary clamps or in existing trench /

pipe of following size of cables

(A) 4 core 16 Sq. mm

Rupees One Hundred EightyFour

Paise EightyThree Only

Making trench in Hard Murrum / Tar Road of suitable width of

cm or required depth for laying any size of cable or locating the Rupees SeventyFour Paise

5 1350.00 fault all over the run and back filling the same and making the 74.74 Mtr

SeventyFour Only

surface as normal ground.

(B) If additional machinery like hammer driller or JCB use [Add]

Rupees Three Hundred

FiftySeven Paise FiftyFour Only

Replacing Old and u/s by Providing & laying approved make

Double walled corrugated pipes (DWC) of polyethylene(conforming

to IS 14930 II )with necessary connecting accessories of same

material at required depth in existing trench for laying of cable.

below ground / road surface for enclosing cable

(A)50 mm outer dia Rupees SixtyTwo Paise

Replacing Old and u/s by Solder less crimping type Aluminium lugs

conforming to IS suitable for cable of following size evenly crimped

8 with high pressure tool & connected to switchgear terminals with

brass/cadmium plated nut bolts in an approved manner.

15.15 Rupees Fifteen Paise Fifteen Only Ea.

Replacing Old and u/s by Supplying and erecting approved make

Octagonal pole made from HR sheet steel. The pole should be

made as per IS. and shall be coated with hot dip galvanizing as per

IS 2629/2633/4759, suitable suspend local wind speed with integral

Junction box consist of terminal plate of min 6mm Hylam sheet,

9 standard profile 35mmX7.5mm Din-Rail for MCB Mounting, stud

type terminal and arrangement for cable termination to be erected

With Suitable foundation (Included) as per details given by

manufacturer considering site requirement.

(D) 6 Mtr. Long 70 mm Top X 135 mm bottom dia, 3 mm thickness

with 200mmX200mmX12mm base plate, 4-M20 Bolts and 600mm Rupees Nine Thousand Eleven

long with necessary G.I. J Bolts .Approx Pole weight 59 kg Paise TwentyTwo Only

Providing and erecting street light pole bracket comprising main B

Class GI pipe of 4.2 cm/require outside dia. complete with suitable

B Class G.I sleeve tubing of approx. 45cms.length and suitable for

76.5 mm / 80mm. / require size pole top having sufficient fasteners

for fixing the brackets and having spread of 1 mtr. length with

10 suitable rise as per site condition & suitable welded stiffener

reducer and nipple with check nut complete painted with one coat

of Red oxide / PU base primer and two coats of Aluminium / PU

paint. paint with following nos of arms.

[A] Single Arm bracket 0.5 Mtr

Rupees Four Hundred NinetyOne

Paise EightySeven Only

Replacing Old and u/s by Supplying & erecting approved make IP

55 grade Company fabricated Timer Panel of following capacity for

switch On-Off street lights on time scheduling basis made from 16G

CRCA sheet duly epoxy power painted inside and outside with

hinged doors and locking arrangement consisting of suitable size of

11 4 Pole MCB and 4 pole contactor (cat-III)with analog time switch,

auto manual switch of same make and suitable input and output

Bakelite terminals and with door earthing approved by Engineer in

Rupees Seventeen Thousand

FiftyNine Paise NinetyOne Only

Supplying & erecting earth pit of minimum bore dia.150mm size

approved make Earthing Electrode consisting Pipe-in-Pipe

Technology as per IS 3043-1987 made of corrosion free hot dipped

G.I.Pipes having Outer pipe dia of 50mm having 80-200 Micron

galvanising, Inner pipe dia of 25 mm having 200-250 Micron

galvanising, connection terminal dia of 12mm with constant ohmic

value surrounded by highly conductive compound with high charge

dissipation suitable for following type of applications with chamber

and heavy duty cover. (A)(approved make OEM has to submit test

12 certificate including value of earth resistance of installation duly

stamped and signed by agency and officer Incharge has to ensure

the value of earthing resistane mentioned in test Certificate) &

having back filling compound of (B) Inner chemical (CCM

Compound)- Resistivity:- 0.2 ohm / meter testing as per IEC 62561-

2017, Voltage drop:- < 1 volt at no load & dry form, Sulphar

content:- <2%(C) Back fill Compound :- Earthing compound should

be capable to retain moisture for long time Necessary test report

must be submitted by Agency.

(a) For Electrical Installation up to 440V in normal soil Rupees Four Thousand Five

8 Length of pipe - 1 Mtr 4591.46 Hundred NinetyOne Paise Ea

Back filling compound - 1 Nos Bag of 15 Kg. FourtySix Only

Providing and erecting HOT deep Galvanised iron strip/wire Rupees SeventySeven Paise

4.064mm to 1.626mm. SeventySeven Only

I/We am/are willing to carry out the work at ……………………………………………% above/below percent (shouldbe written in figured and words) of the

estimated rates mentioned above. Amount of my/our tender works out as under.

Estimated amount Estimated amount

Put to tender Rs______________ Put to tender Rs______________

Deduct : ___________ % Above RS__________ Deduct : ___________ % Above RS__________

*(Please strike out whitchever is not applicable).

Note 1 – All work shall be carried out as per public works department handbook and other specification of Division ot as directed.

Note 2 – All the columns is schedule should be filled in ink and the total of the entries in the last column should be struck by the contractor under his

Note 3 – Rates quoted include clearance of site (prior commencement of work and at its close ) in all respects and hold good for work under all

conditions, site, moisture,weather etc.

Note 4 – To be continued on additional sheets, if found necessary.

Note 5 - The rates quoted by the Contractor must be inclusive of all taxes prevailing on due date of bid submission except GST. However, any subsequent

changes in the tax structure by Government after due date of bid submission will be compensated (+/-) on availability or submission of actual

documentation. Contractor will have to intimate Engineer regarding changes occurred in the tax structure after bid submission. If the contractor fails to

provide such information and if any financial obligation may arise due to change in tax structure, same will be recovered from the contractor. GST will be

paid separately on the bills. Hence, it is the responsibility of the contractor to pay the GST to the concerned Authority.

Deputy Executive Engineer Executive Engineer

Electric Sub Division Ukai Division No.1