Rehabilitation of LIS 2017-18 Repair and renovation works to LIS Koodallur in Anakkara Panchayath Palakkad District.

Amount

Appendix A- Civil Works

od331/2020_2021/IA : Supplying and engaging Coolie/Khalasi.

15.9.2 : Demolishing stone rubble masonry manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer -in- Charges:In cement mortar

15.14.1 : Dismantling wood work in frames, trusses, purlins and rafters up to 10 metres span and 5 metres height including stacking the material within 50 metres lead:Of sectional area 40 square centimetres and above

15.14.2 : Dismantling wood work in frames, trusses, purlins and rafters up to 10 metres span and 5 metres height including stacking the material within 50 metres lead:Of sectional area below 40 square centimeters

15.28.1 : Dismantling roofing including ridges, hips, velleys and gutters etc., and stacking the material within 50 metres lead of :G.S. Sheet

od329/2020_2021/IA : Supplying and engaging Fitter - for dismantling motor ,pump,pipe,starter for the construction work and making small repair and refitting the same after completion

od2232/2017_2018/IA : Supplying and engaging wire man - for dismantling motor ,pump,pipe,starter for the construction work and making small repair and refitting the same after completion

od2230/2017_2018/IA : Engaging Man Coolie for dismantling and stacking the old pipes of all diameter as per the directions of deptl. officers at site

2.6.1 : Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil

5.3 : Reinforced cement concrete work in beams, suspended floors, roofs, having slope up to 15⁰ landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with1:1.5:3 (1 cement : 1.5 coarse sand (Zone III) : 3 graded stone aggregate 20 mm nominal size).

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

4.3.1 : Centering and shuttering including strutting, propping etc. and removal of form work for:Foundations, footings, bases for columns

4.1.3 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

5.9.3 : Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.9.5 : Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.9.16.1 : Centering and shuttering including strutting, etc. and removal of form for:Edges of slabs and breaks in floors and wallsUnder 20 cm wide

5.1.2 : Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

50.6.1.5 : Solid block masonry using pre cast solid blocks ( Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 Part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement : 6 coarse sand) etc complete

10.5.1 : Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer.Using M.S. angels 40x40x6 mm for diagonal braces

13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

5.23 : Smooth finishing of the exposed surface of RCC work with 6mm thick cement mortar 1:3 ( cement : 3 fine sand).

13.61.1 : Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work

13.43.1 : Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

13.46.1 : Finishing walls with Acrylic Smooth exterior paint of required shade:New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

13.71 : Lettering with black Japan pint of approved brand and manufacture

Appendix B - Pipe and Allied works

od57151/2019_2020/IA : MS Pipes 350mm - Manufacturing supplying and fitting 350mm dia MS pipe of various length with shell thickness 6mm including painting with 2 coats of red oxide primer, laying the same to line and level as directed by departmental officers at site.

od57155/2019_2020/IA : MS - Flanges for 350mm pipe-Manufaturing supplying and fitting 350 mm dia MS Flange having shell thickness 10 mm depth 75mm with suitable bolt holes fixing the flange in position with required welding around the flange, pipe joint grinding for smoothing the welded portion, including painting with red oxide primer etc. complete

od57156/2019_2020/IA : MS Pipes 250mm - Manufacturing supplying and fitting 250mm dia MS pipe of various length with shell thickness 6mm including painting with 2 coats of red oxide primer, laying the same to line and level as directed by departmental officers at site.

od64553/2019_2020/IA : MS - Flanges for 250mm pipe-Manufaturing supplying and fitting 250 mm dia MS Flange having shell thickness 10 mm depth 75mm with suitable bolt holes fixing the flange in position with required welding around the flange, pipe joint grinding for smoothing the welded portion, including painting with red oxide primer etc. complete

od69178/2019_2020/IA : Manufacturing supplying and fitting 350mm dia M.S bend of various length with shell thickness 6mm including painting with 2 coats of red oxide primer, laying the same to line and level as directed by departmental officers at site..

od69179/2019_2020/IA : Manufacturing supplying and fitting 250mm dia M.S bend of various length with shell thickness 6mm including painting with 2 coats of red oxide primer, laying the same to line and level as directed by departmental officers at site..

od3221/2020_2021/IA : Providing and Fixing C.I Non Return Valves 250mm diameter complete with bolts,nuts,rubber insertions etc as per direction of Engineer - in - Charge

od69172/2019_2020/IA : Supplying ,Erecting and commissioning of new 10 HP Vacuum pumpset of Kirloskar make with suitable Starter Panel ,main switch etc for priming the suction lines of LIS as per direction of Engineer - in - Charge

od69173/2019_2020/IA : Supplying 2T capacity Chain and pulley set (lifting chain 10m long)-make "Indef"- with all necessary accessories

od69174/2019_2020/IA : Supplying Tripod for hanging the Chain & pulley for lifting the equipments - with 2" GI pipes- 3m long - 3 No.s and with Plate fabrication

od3222/2020_2021/IA : Supplying necessary tools for L.I.Scheme asper the list 1.Spanner Ring 6x7 Taparia, 2. Spanner Ring 30x32 Taparia, 3. Spanner Double End DEP 6x7 Taparia, 4. panner Double End DEP 30x32 Taparia, 5.Adjustable Spanner 1173 - 12" Taparia, 6. Screw Driver Flat 250x6, 826 Taparia, 7.Screw Driver Two in one 905 Taparia, 8. Tester 818 Taparia, 9.Tester 905 Taparia, 10. Hammer 1.5Lb wooden Handle Python/ Tiger HMC 11, 11. Hammer 2Lb wooden Handle Python/ Tiger HMC 11, 12. L Handle 1735 Taparia, 13. Tubular Box Spanner TS 6x7 Taparia, 14. Tubular Box Spanner TS 30x32 Taparia, 15. Grease Gun PLG 513 Prima, 16. Pipe wrench 1275 - 450mm Taparia, 17. Pipe wrench 1275 - 350mm Taparia, 18. Hacksaw Frame Tiger / Eastman Square HMC 44, 19. Hand Gloves Cotton PVC Coated Blue P 660 10",20 CVombination Plier 1621 - 8" Taparia, 21. Nose Plier Long 1430-6" Taparia, 22. Crow Bar 1.6, etc

M V KUNHI MOHAMED

Bidder Name

VT UMMER

M V KUNHI MOHAMED