Interior work for the Setting up of PIU Office in COIR BHAVAN ,Trivandrum for KERA Project.

Amount

CIVIL_PLUMBING AND ELECTRICAL WORKS

15.12.1 Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead Of area 3 sq. metres and below

50.17.1.4 Supplying and fixing CP Health faucet good quality including cost of materials and labour charges etc. complete as per the direction of site engineer-in-charge.

Providing and fixing CP brass long body bib cock of approved quality : with ISI mark 15 mm nominal bore

50.17.1.1 Supplying and fixing Stainless steel soap dish including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.

50.17.1.3 Supplying and fixing CP Towel rod 60cm or nearest available length including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.

17.31 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete

14.43 Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

13.26 Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

13.82.2 Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound) content less than 50 grams/ litre, of approved brand and manufacture including applying additional coats wherever required, to achieve even shade and colour. Two coats

15.39.3 Dismantling wooden boardings in lining of walls and partitions, excluding supporting members but including stacking with in 50 metres lead: Thickness above 25 mm upto 40 mm

Engaging un-skilled labours for extra where ever necessary as per instruction of engineer in charge

EXECUTIVE TABLE: Fabrication and installation of an Executive Table of size 1800x900x750 mm using 16 mm thick BWP Grade 710 marine plywood finished laminated on all sides with 1.00 mm thick decorative laminates (exterior) & 0.8mm balancing laminate (interior), including a single- side covered storage with telescopic channels and SS hinges. All visible edges shall be provided with 2mm PVC edge-band, and the unit will be provided with necessary ISI marked SS hardware such as handles, locks, and screws, complete in all respects as per design and instructions of Engineers in charge

SIDE STORAGE WITH SHUTTERS (Size:1000x 450X730mm ) : Fabrication, supply, and installation of Side Credenza made with 16 mm thick BWP Grade 710 Marine Plywood, laminated on all sides with 1.0 mm thick decorative laminate (exterior) and 0.8 mm balancing laminate (interior). All visible edges to be edge-banded with 2 mm PVC edge tape. Unit to include shutters & drawers. In addition, a desk open nichie with branded grommet shall be integrated on the top surface of the credenza & compartments as per approved design and fitted with all required brand, ISI marked hardware including hinges, handles, locks, magnetic catchers, etc.

EXECUTIVE TABLE (Size:1500x 750X750mm) : Fabrication and installation of an Executive Table of size 1500x750x750 mm using 16 mm thick BWP Grade 710 marine plywood laminated on all sided with 1.00 mm thick decorative laminates (exterior) an 0.8 mm balancing laminate(interior) , including a single-side storage cupboard and drawer with shutters telescopic channels and SS hinges. All visible edges will be 2mm PVC edge-banded, and the unit will be provided with necessary SS hardware such as handles, locks, and screws, complete in all respects as per design and instructions of Engineers in charge

REAR WALL CREDENZA/STORAGE UNIT(Size: 2500x300x900mm) : Fabrication and installation of approved size as per the design . The storage unit shall be made of 18 mm thick BWP Grade 710 marine plywood , with 1.00 mm thick decorative laminates (exterior) an 0.8 mm balancing laminate (interior) The unit shall be provided with three horizotal platforms to cover the entire length & vertical partitions where ever required, besides covering rear side of the unit 700mm. All visible edges will be provided with 2mm PVC edge-banded, and the unit will be provided with necessary Stailess Steel hardware such as handles, locks, and screws, complete in all respects as per design and instructions of Engineers in charge

CONFERENCE TABLE (Size:3000x 1000X750mm) : Fabrication and installation of an Executive Table of size 3000x1000x750 mm using 18 mm thick BWP Grade 710 marine plywood laminated on all sided with 1.00 mm thick decorative laminates (exterior) an 0.8 mm balancing laminate(exterior) , all visible edges will be 2mm PVC edge-banded. The top size would be 3000x1000mm of approved design. Besides full length central support, four additional vertical suppor & required supports to rest top plywood (if any) for stabiliy are also to be provided complete in all respects as per design and instructions of Engineers in charge

9.105.1 Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with Zinc coating of 120 gms/ (both side inclusive), consisting of floor and ceiling channel 50 mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete. 75 mm overall thickness partition with 12.5 mm thick double skin fire rated Glass Reinforced Gypsum (GRG),plaster board conforming to IS : 2095 : (part 3) 1996 (Board with BIS Certification marks)

SLIDING GLASS DOOR FOR CABINS (Size :900x 2100mm ): Providing & fixing of 12mm Thick toughened float glass door (clear or frosted as approved), with machine-polished and chamfered edges, mounted on a heavy-duty stainless steel top sliding track system with a 60 kg capacity and soft-close mechanism.with all necessary hardware's in all respects as per approved design and the direction of the Engineer-in-Charge

Fixed glass partitions: Providing & fixing of 12mm Thick toughened glass partition (clear/frosted as per approved design) with machine-polished and chamfered edges. Glass shall conform to IS:2553 (Part I) standards. All joints shall be silicone-sealed neatly with matching neutral-cure sealant. The work shall include all necessary approved hardware fittings such as brackets, clamps, corner connectors, spacers, and beading, complete in all respects , as approved by the Engineer-in-Charge.

FROSTED FILM: Providing and fixing of approved shade of 100 gsm frosted film as per design.The film will be applied after all necessary suface preparation.

ROMAN BLINDS :Providing and fixing roman blinds of approved shade & design, make imported superior polyester base fabric vanes with scotch guard application operated through a smooth and durable pulley with head rail mechanism, and fixed using standard brackets, screws, and accessories as manufacturer’s instructions and the direction of the Engineer-in-Charge.

Providing work station unit, Comprising of 15 units of different sizes, ie, L shape-2130X600X750mm- (10 nos) & (1200X600X750mm-5 nos) and storage unit of size(1280X600X750 mm) with following specification. Table and partition material to be used for the work station is 16mm thick 710 grade plywood laminated on both sides with 1 mm thick decorative lamition of approved shade and finish. User end of the work station table shall be 750mm and other sides shall not be less than 1400mm from FFL.(For all stations). For the central bay of work station (5 units) 3 sided ply wood partition to be provided and other two bays two sided partition to be provided. For all the 15 stations side drawyers are to be provided as per the drawing enclosed. Approximate size of side drawyers shall be 500X600X200mm & 500X600X500mm. All the drawyers are to be provided with SS handle (100 mm). Approved make lock & key SS auto closing hinges. Powder coated aluminium guide channels, magnetic stopper , desthole cut outs and gromments for cable routing etc complete. All sides of shutters, drawyers, partituons etc. shall be provided with 2mm thick PVC edge board. Additional storage unit(1no) shall also be provided with two open storage unit of size 1280X600X750 mm using 16mm thick 710 grade playwood for keeping stationery items Note: 1 unit of work station includes 15 indepentant work stations, central partitions, Drawyers for all 15 work stations etc.

OPEN STORAGE CABIN (Size:2000x 300X1200mm -1nos) : Fabrication and installation of storage cabin of approved size as per the design . The cabinet will be made of 16mm thick BWP Grade 710 marine plywood finished with 1.00 mm thick decorative laminates (exterior) an 0.8 mm balancing laminate(Interior) , the cabin should have 4 horizontal platform (2000mm) & 4 vertical supports (1200mm). All visible edges will be 2mm PVC edge-banded, as per design and instructions of Engineers in charge etc. as required.

TWO SETER SOFA (1400X850X900mm): Providing, supplying and placing of`two seater sofa (1400X850X900mm) with SEAT FOAM. The seat is made up of PU foam in Density 28 kg/cu.mtr 75 mm thick with an additional top layer of supersoft PU foam in Density 32 kg/cu, 50mm thick upholstered with fabric or leatherette. BACK FOAM The back is of PU foam in Density 28 kg/cu mtr with two additional top layer of supersoft foam of density 32 kg/cu mtr 100 mm thick, upholstered with fabric or leatherette. UNDERSTRUCTRE : Understructure 1s made up of 12 mm thick hot pressed plywood [moisture resistance & termite proof as per IS:303] & pinewood of cross sections devoid of major knots & surtace defects 6 nos per seat & 3.8mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose LEG ASSEMBLY: It is a welded Assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap.

STORAGE BELOW TV CABIN (Size:1500x 350X300 mm ) : Fabrication and installation of tv cabinet , fabricated using 16 mm thick BWP Grade 710 Marine Plywood, 1.00 mm thick decorative laminates (exterior) an 0.8 mm balancing laminate(interior) . The unit consist of two no.s of horizontal platform (1500mm) & four vertical supports (300mm) besides covering of rear side as per approved design, and all visible edges shall be machine-edge banded using 2 mm thick PVC edge tape.

SEMI EXECUTIVE MEDIUM BACK REVOLVING CHAIR Providing and supplying of eargonomically designed fabric upholstered high back revolving chair.The seat cushion of the chair should be made up of 50mm thick high density of 45kg /m3 polyurethane mould and back cushion should be made up of 38mm thick high density 33 kg/m3 the polyurethane foam shall be as per manufacturer's specification.The hardness of foam shall be 20 kg on hampden machine and 25% compression and it should be covered with as per manufracturer's shade card.The arms of the chair should be black.The gas lift mechanism shoud be tested as per standars.The pedestal should be 5 legged injection mouldedin black nylonand fitted with 5 Nos twin wheel castors.The castors of the chair should be glass filled ,twin wheel castors and tested to perform 1 lakh cycles with 225 lbs load . note-The back and base of chair should be supplied with black polypropylene fabric upholstered.Overall height of chair should be minimum 1050 mm (incluseive of maximum adjustment of gas liG mechanism).

PREMIUM HIGH BACK REVOLVING CHAIR Providing and supplying of eargonomically designed fabric upholstered high back revolving chair.The seat cushion of the chair should be made up of 50mm thick high density of 45 kg /m3 polyurethane mould and back cushion should be made up of 38mm thick high density 33 kg/m3 the polyurethane foam shall be as per manufacturer's specification.The hardness of foam shall be 20 kg on hampden machine and 25% compression and it should be covered with as per manufracturer's shade card.The arms of the chair should be black.The gas lift mechanism should be tested as per standars.The pedestal should be 5 legged injection mouldedin black nylonand fitted with 5 Nos twin wheel castors.The castors of the chair should be glass filled ,twin wheel castors and tested to perform 1 lakh cycles with 225 lbs load . note-The back and base of chair should be supplied with black polypropylene fabric upholstered.Overall height of chair should be minimum 1225 mm (inclusive of maximum adjustment of gas liG mechanism).

SEMI EXECUTIVE CHAIR/ VISITORS CHAIR: Upholstered with 50mm thick moulded PU foam with density 32kg/m3 as per the shape ad covered with tapesly cloth of superior quality. Bottom frame is made from 32/25mm dia MS ERW Crc tube with necessary stiffners and powder coated in seven tank process. Back rest with breathless mesh fabric. Overall height of the chair not less than 900mm

Supply, Installation, Testing and Commissioning of 2 TR - 5 Star rated Inverter type split AC units , Hi-wall mounted, preferably with anti corrosive / powder coated outdoor units, fitted with hermitically sealed suction cooled energy efficient Scroll / Rotary compressor operating on R-32 / HFC-134a / 407 C / 410 A refrigerant suitable for operation on 220 V, 1 Ph, 50 Hz A/C supply. The units shall be inclusive of all standard accessories like power & control cables, good quality copper tubing of minimum 3 meter length to interconnect the outdoor unit with indoor unit for refrigerant lines, elastomeric Nitrile rubber insulation, clamps etc. Notes: (1) Condenser tubes, Evaporator tubes & connecting pipes should be made out of good quality copper. (2) High-energy efficient compressor of rotary / Scroll type (3) Cordless remote for setting Temp, on time, off time, power saving mode, auto mode operation, sleep mode, auto setting with memory backup, time delay feature, programmable timer, etc. with real-time clock. (4) Warranty: 5 Years on PCB, 10 years warranty on compressor and one year warranty for the total system from the date of handing over/ commissioning Make: Blue Star / Voltas / Carrier Midea / Hitachi / Daikin / Panasonic / Mitsubishi / Toshiba /Haier / O General or equivalent

"DG set of the rating 50 kVA Prime Diesel generating set comprising of diesel engine alternator, fuel tank, starting system, battery, battery charger, electronic governor etc with all accessories required for synchronising the DG with another DG's. The battery charger of auxillary DC power supply unit, with dry batteries with connecting leads and terminals with stationary type, high discharge perfomance, Valve Regulated Lead Acid (VRLA) sealed maintenance free, battery charger including all other accessories like interconnecting cables etc as required. The Generator set shall have a integral type acoustic enclosure as per latest CPCB II norms. Diesel engine shall be suitable for continuous operation of generator set and satisfies with EURO-II specifications. (Energy meter& CTs shall be tested and certificate shall be obtained from electrical inspectorate lab) Following sanction may be obtained by the contractor: (i) Sanctions from Municipality/ Corporation (ii)Sanction from Pollution control Board (ii) Sanction from electrical inspectorate Acoustic insulation material shall be mineral wool/ resin bounded fibre glass of grade 64 and 98 kg/meter cube, having an N.R.C value of 0.96 and 1.21 (with minimum thickness of 50mm. The 48kg/meter cube shall be with black glass tissued faced 40kg/meter cube. RP tissue shall be used in between metal and insulation. Doors shall be openable on either side. Exhaust fan of sufficient capacity tube lights etc. shall be provided inside the enclosure. Sufficient fresh air intake and hot air outlet with splitters to be arranged so that the temperature inside should not increase to 5 degree above ambient temperature. (The enclosure shall bare certificate from the generator manufacturer conforming the CPCB II norms and serial numbers of the test certificate). Exhaust pipe inside the enclosure upto and including silencer shall be enclosed with Al cladding over thermal insulation. Foundation shall be done by other agency."

1.10.3 : Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVCinsulated copper conductor single core cable in surface / recessed medium class PVC conduit,with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLSPVC insulated copper conductor single core cable etc as required.Group C

1.55.3 : Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.Group C

1.33 : Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden blockincluding connection etc as required.

1.14.1 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required 2x1.5 sq.mm + 1x1.5 sq.mm earth wire.

1.14.2 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

1.14.7 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required4 X 2.5 sq. mm + 2 X 2.5 sq. mm earth wire

1.14.3 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2 X 4 sq. mm + 1 X 4 sq. mm earth wire

1.21.1 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm

1.21.2 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm

1.21.3 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.32 mm

Supply and clamping the following size of corrugated pvc fiexible conduit with necessary locking ring and check nut at termination pointed using suitable size GI saddles spacing not exceeding 60 cms on surface including making good the damages, colour washing etc.as required 20mm dia .

Supply and clamping the following size of corrugated pvc fiexible conduit with necessary locking ring and check nut at termination pointed using suitable size GI saddles spacing not exceeding 60 cms on surface including making good the damages, colour washing etc.as required<br>25mm dia

1.17.5 : Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.5 X 1.5 Sq. mm

1.17.14 : Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.5 x 2.5 sq. mm

1.24.1 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 amps switch

1.24.3 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.15/16 amp switch

1.24.4 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.3 pin 5/6 amp socket outlet

1.24.5 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.6 pin 15/16 amp socket outlet

1.27.1 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.1 or 2 Module (75mmX75mm)

1.27.2 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.3 Module (100mmX75mm)

1.27.3 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.4 Module (125mmX75mm)

1.27.5 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.8 Module (125mmX125mm)

90.10.3.15 : Supply and Fixing the following modular switches & accessories in the existing front plates and giving necessary connections as required (RoHS compliant

1.27.6 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.12 Module (200mmX150mm)

1.58 Supplying and fixing PVC batten/ angle holder including connection etc. as required.

1.26 : Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

1.31 : Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residentia buildings).

Supply, conveyance, installation, testing and commissioning of led Slim panel Surface light with all accessories, housing made up of die cast aluminium for better heat management. Hight Transmittivity Diffuser for better light output and uniform light distribution without glare. Driver and accessories are pre wired for easy installation and long service. Voltage 230 v,CRI>80,Powerfactor>0.95, System Luminous efficacy 100LM/W;LED light source : SMD, Beam angle: 120 degree,CCT WH,WW NW, Color temperature>6000K, IP20, Ambient temp-0 to 45DegC, Driver efficiency>85%, THD<15%, Surge protection 4 KV, Multistage Isolated Constant Current operated driver with range 150-270V AC and Safety Extra Low Voltage Safe level<60V DC as per IEC standard.Round Slim surface mounted, Wattage 15 W, similar to Luker, Wipro ,crompton,or Equivalent with luminaire lumen 2000 lm and giving connection with 3 core round flex wire .etc .complete.<br>

Supply, conveyance, installation, testing and commissioning of led Slim panel Surface light with all accessories, housing made up of die cast aluminium for better heat management. Hight Transmittivity Diffuser for better light output and uniform light distribution without glare. Driver and accessories are pre wired for easy installation and long service. Voltage 230 v,CRI>80,Powerfactor>0.95, System Luminous efficacy 100LM/W;LED light source : SMD, Beam angle: 120 degree,CCT WH,WW NW, Color temperature>6000K, IP20, Ambient temp-0 to 45DegC, Driver efficiency>85%, THD<15%, Surge protection 4 KV, Multistage Isolated Constant Current operated driver with range 150-270V AC and Safety Extra Low Voltage Safe level<60V DC as per IEC standard.Round Slim surface mounted, Wattage 18 W, similar to Luker, Wipro ,crompton,or Equivalent with luminaire lumen 2000 lm and giving connection with 3 core round flex wire .etc .complete.<br>

Supply, conveyance, installation, testing and commissioning of led Slim panel Surface light with all accessories, housing made up of die cast aluminium for better heat management. Hight Transmittivity Diffuser for better light output and uniform light distribution without glare. Driver and accessories are pre wired for easy installation and long service. Voltage 230 v,CRI>80,Powerfactor>0.95, System Luminous efficacy 100LM/W;LED light source : SMD, Beam angle: 120 degree,CCT WH,WW NW, Color temperature>6000K, IP20, Ambient temp-0 to 45DegC, Driver efficiency>85%, THD<15%, Surge protection 4 KV, Multistage Isolated Constant Current operated driver with range 150-270V AC and Safety Extra Low Voltage Safe level<60V DC as per IEC standard.Round Slim surface mounted, Wattage 30 W, similar to Luker, Wipro ,crompton,or Equivalent with luminaire lumen 2000 lm and giving connection with 3 core round flex wire .etc .complete.<br>

Supply and installation of pedastial FAN<br>Supply and installation of wall fan, white colour, metal leaf, 5 star rated as per BEE complete with blades, casing , wall mounting accessories etc(Make Havells/bajaj/usha/V-guard/crompton)

Exhaust Fan: Supply of 250mm sweep, 900rpm light duty exhaust fan shutter type white colour, 9&quot; or 10&quot; star rated as per BEE, with its all accessories including mounting as required for complete installation.(Make Havells/bajaj/usha/V-guard)

Supply and installation of the 9W LED lamp and other accessories in the existing point

1.38 : Supplying and fixing call bell/ buzzer suitable for single phase, 230 volts, complete as required.

Supply and installation of Mirror lights of 9 Watts ; CCT : 3 in 1 ; Material: Alu Die Cast; Body colour: white ; IP rating : IP 20

90.11.1.15 : Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required6 way (8+18) - double cover TPN vertical DB with provision for fixing 4P MCB / Isolator/ RCCB/ RCBO as incomer and SP/ TP MCB as outgoing (IP 42/43)

90.11.1.18 : Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required4 way (8+12) - double cover TPN vertical DB with provision for fixing MCCB as incomer and SP/ TP MCB as outgoing (IP 42/43)

2.2.1 : Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required100 Amp, 16 KA, TPMCCB

2.10.1 : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole

2.10.5 : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Triple pole and neutral

2.13.2 : Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps

2.15.3 : Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps

5.17 : Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing as required.

90.16.1.3 : Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required3.15 mm copper conductor ( 10 SWG)

90.16.1.5 : Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required4.75 mm copper conductor (6 SWG)

90.16.5.3 : Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required.3.15 mm (10 SWG)

90.16.5.4 : Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required.4.00 mm (8 SWG)

90.16.5.5 : Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required.4.75 mm (6 SWG)

90.12.7.2 : Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.2 core 6 sq mm with factory made clamp

90.12.7.27 : Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.3.5 core 25 sq mm with factory made clamp

90.12.7.40 : Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.4 core 10 sq mm with factory made clamp

90.12.7.41 : Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.4 core 16 sq mm with factory made clamp

9.1.1 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.2 X 6 sq. mm (19mm)

9.1.20 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X25 sq.mm (28mm)

9.1.32 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 10 sq. mm (25mm)

9.1.33 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 16 sq. mm (28mm)

HIKVISION-7616NXI-K1 NVR : 16-ch 1U K Series AcuSense 4K NVR Up to 16-ch IP camera inputs, H.265+/H.265/H.264+/H.264 video formats, Up to 1-ch@12 MP or 2-ch@8 MP or 4-ch@4 MP or 8-ch@1080p decoding capacity, Up to 160 Mbps incoming bandwidth ,Adopt Hikvision Acusense technology to minimize manual effort and security costs

HIKVISION DS-2CD1023G0E ; 2 MP Fixed Bullet Network Camera High quality imaging with 2 MP resolution ; Ecient H.265+ compression technology, Clear imaging against strong back light due to DWDR technology ; Water and dust resistant (IP67) ; EXIR 2.0: advanced infrared technology with long IR range

Western Digital 4TB ; WD Purple Surveillance Internal Hard Drive HDD - SATA 6 Gb/s, 256 MB; Cache, 3.5" - WD42PURZ

Cat 6 Cable and Other items ; Supply and Installation Of Cat6 Cable, Pipe and Fitting, Camera Box, Camera ; Rack, Patch Panel, and other Items.

supply , installation, testing and commissioning of LED SMART TV 43" with Remote Control, Power Cord, Wall mount bracket, Black Color etc having minimum 3 year warranty of premium brand of approved color including the cost of materials, freight, loading & unloading charges etc complete. Connectivity options usually include three HDMI ports, two USB ports, Bluetooth, dual-band Wi-Fi, and Ethernet. Audio output may be supported by Dolby Audio or DTS, with speaker output ranging from 20W to 30W. (LG, Samsung, VU or equivalent )

supply , installation, testing and commissioning of LED SMART TV 55" with Remote Control, Power Cord, Wall mount bracket, Black Color etc having minimum 3 year warranty of premium brand of approved color including the cost of materials, freight, loading & unloading charges etc complete. Connectivity options usually include three HDMI ports, two USB ports, Bluetooth, dual-band Wi-Fi, and Ethernet. Audio output may be supported by Dolby Audio or DTS, with speaker output ranging from 20W to 30W. (LG, Samsung, VU or equivalent )

DS-3E1Hikvision 518P-EI/M 16 Port Gigabit Smart POE Switch ; 16 x gigabit PoE RJ45 ports, 1 × gigabit RJ45 port, 1 x gigabit ber optical ;port, Total PoE power budget 130 W, Unied cloud management for security ; systems, Network topology at your ngertips, Remote troubleshooting, Visualized topology management, Up to 300 m long-range PoE transmission, 6 kV surge protection

1.24.7 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.TV antenna socket outlet

1.53.1 Supplying and drawn of UTP 4 pair CAT 6 LAN cable in the existing surface/recessed steel/PVC conduit as required1 run of Cable

Supply , installation , testing and commissioning of SWITCH D-LINK 24 PORT GIGA(10/100/1000) DGS-1024D

Supply , installation , testing and commissioning of DLINK CAT6 24 PORT PATCH PANEL NPP-C61BLK241

Supply and Installtion of KEYSTONE JACK DLINK CAT

Supply and Installtion of FACE PLATE DLINK SINGLE

Supply and Installtion of D-LINK PVC 3x3 BACK BOX FOR SINGLE/DUAL

Cat6 Cable and Other items : Supply and Installation Of Cat6 Cable, Pipe and Fitting, Camera Box, Camera Rack, Patch Panel, and other Items.

supply and installtion of TP-Link Deco X20 : TP-Link Deco X20(3-Pack) 1800 Mbps Whole Wi-Fi 6 System Mesh Router

Supply and installtion of D-LINK CLOSED CABLE MANAGER 1U

supply and installtion of RACKSPACE RACK 9U 500D

Supply installation, testing and commissioning of following three phase to three<br>phase UPS indoor (IP20) in stand alone configuration,true online double<br>conversion DSP based UPS system in stand alone configuration with inbuilt<br>parallel kit capable of connecting UPS in parallel mode when required without<br>additional cost, with 15 min backup battery ( battery of reputed make) with, input<br>pf>.99, less input current consumption, with necessary battery circuit breaker.,<br>with input 415V, 50Hz three phase, output 240V, IGBT rectifier and IGBT inverter.<br>It shall be 100% generator compatabile with efficiency > 94% and output power<br>factor > 0.9 and including all accessories etc as required. The UPS system shall<br>be with automatic & manual maintenance bypass switch facility.UPS shall<br>have seperate battery bank, and batteries shall be connected in single string.The<br>system shall comply to IEC /EN 62040-1 and relevant IS standard.The acoustic<br>noise of the system should be less than 58dB.The system shall comply to IEC /EN<br>62040-1, EN/IEC 62040-2, EN/IEC 62040-3 and relevant IS standard.<br>5 kVA UPS - 1No Battery circuit Breaker-1No Battery - Required nos.<br>of SMF for providing 15 Minutes Back UP and Battery Accessories like battery<br>rack, interconnecting cables et

Disposal of building rubbish/ malba/ similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved

Providing and placing polyethylene water storage tank :ISI 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings with 4m height MS support- Temporary

Providing and placing Aluminium cool white LED Flood light 100 W including wiring

Supply and fixing of Green Net including the required supportings

Providing and placing of Portable FRP E-toilet (900x900x2250 mm) including Septic tank and plumbing materials

Supply of PPE (Helmets, Gloves, Safety boots, mask)

Providing and placing 3 litre capacity fire estiguisher

Providing provisions to instil workers to ensure a safe working environment, all statutory requirements as drected by the engineer in charge and the consultant environmentalist.

Supply and fixing 'KERALA CLIMATE RESILIENT AGRI VALUE CHAIN MODERNISATION PROJECT (KERA)' Name Board including logo using SS letter box 15 cm height

Supply and installation of a name board for the 'KERALA CLIMATE RESILIENT AGRI VALUE CHAIN MODERNISATION PROJECT (KERA)', including the logo, made of acrylic LED signage mounted on ACP (Aluminium Composite Panel), with letter height of 30 cm, complete with all necessary lighting arrangements. etc complete as per design and direction of engineer in charge

Supply and installation of the Top Hot & Cold 11L Water Purifier Kiosk, featuring an inbuilt RO+UV system, includes all necessary fittings. Dimensions of 380 x 340 x 1140 mm and operates at a rated power of 700 watts with a voltage of 230V. Plastic body

N.AJANTHA KUMAR (BID ID -2224886)

M K KAVITHA (BID ID -2224915)